PMC IDE Hard Disk Adapter, GFK-2079
GE Fanuc Automation
Programmable Control Products
IC697VHD100
PMC IDE Hard Disk Adapter
Installation Manual
GFK-2079
514-750432-000 A
April 2002
GFL-002
Warnings, Cautions, and Notes
as Used in this Publication
Warning
Warning notices are used in this publication to emphasize that hazardous voltages,
currents, temperatures, or other conditions that could cause personal injury exist in this
equipment or may be associated with its use.
In situations where inattention could cause either personal injury or damage to
equipment, a Warning notice is used.
Caution
Caution notices are used where equipment might be damaged if care is not taken.
Note
Notes merely call attention to information that is especially significant to understanding and
operating the equipment.
This document is based on information available at the time of its publication. While efforts
have been made to be accurate, the information contained herein does not purport to cover all
details or variations in hardware or software, nor to provide for every possible contingency in
connection with installation, operation, or maintenance. Features may be described herein
which are not present in all hardware and software systems. GE Fanuc Automation assumes no
obligation of notice to holders of this document with respect to changes subsequently made.
GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory
with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or
usefulness of the information contained herein. No warranties of merchantability or fitness for
purpose shall apply.
The following are trademarks of GE Fanuc Automation North America, Inc.
Alarm Master
CIMPLICITY
CIMPLICITY 90–ADS
CIMSTAR
Field Control
GEnet
Genius
Helpmate
Logicmaster
Modelmaster
Motion Mate
ProLoop
PROMACRO
PowerMotion
PowerTRAC
Series 90
Series Five
Series One
©Copyright 2001 GE Fanuc Automation North America, Inc.
All Rights Reserved
Series Six
Series Three
VersaMax
VersaPro
VuMaster
Workmaster
Contents
Chapter 1
Introduction, Description, and Specifications ......................................... 1-1
Reference Material and Other GE Fanuc Manuals................................................... 1-1
General Description ................................................................................................. 1-2
Safety Summary ....................................................................................................... 1-3
Chapter 2
Configuration and Installation.................................................................. 2-1
Physical Installation ................................................................................................. 2-2
Connector Pinouts .................................................................................................... 2-4
Chapter 3
Theory of Operation .................................................................................. 3-1
Chapter 4
Maintenance................................................................................................ 4-1
Appendix A
System Driver Software............................................................................ A-1
Introduction............................................................................................................. A-1
Ultra DMA/66/100 Driver Disk Preparation........................................................... A-2
GFK-2079
iii
Chapter
Introduction, Description, and Specifications
1
This manual describes installation of the IC697VHD100 PMC IDE Hard Disk Adapter.
Reference Material and Other GE Fanuc Manuals
For the most up-to-date physical description and specifications for the IC697VHD100, refer to:
GE Fanuc specification number GFK-2112.
The following IEEE Specifications apply to the IC697VHD100:
IEEE P1386.1 PMC Mezzanine Card (PMC) Specification
IEEE Standards Department
Copyright and Permissions
445 Hoes Lane, P.O. Box 1331
Piscataway, NJ 08855-1331
IEEE P1386 Common Mezzanine Card (CMC) Specification
IEEE Standards Department
Copyright and Permissions
445 Hoes Lane, P.O. Box 1331
Piscataway, NJ 08855-1331
PCI Local Bus Specification, Revision 2.1
PCI Special Interest Group
P.O.Box 14070
Portland, OR 97214
1-800-433-5177 (USA)
503-797-4207 (International)
GFK-2079
1-1
1
General Description
The IC697VHD100 provides access to both an on-board hard disk drive and to external disk drives.
The on-board hard disk is logically located on the Primary Channel and can perform Ultra DMA
transfers up to 66Mbytes/second with Bus Mastering.
Up to two external drives can be connected to the IC697VHD100. These drives are connected via
a 40-pin header extended through the front panel. These drives are logically located on the
Secondary Channel and can perform Ultra DMA transfers up to 100Mbytes/second with Bus
Mastering.
The IC697VHD100 is designed to meet all requirements, both physical and electrical, of the IEEE
P1386.1 PCI Mezzanine Card (PMC) Specification and the IEEE P1386 Common Mezzanine Card
(CMC) Specification. The user can connect this board to any GE Fanuc processor board
configured to receive a PMC-type card. The IC697VHD100 also conforms to Revision 2.1 of the
PCI Local Bus Specification.
Board Features
1-2
•
On-Board Ultra DMA 66 Hard Disk Drive
•
External Ultra DMA 100 Disk Drive interface via front bezel header
•
Drive activity LEDs for both Primary and Secondary Channels
•
PCI Local Bus Specification Revision 2.1 compliant
•
PCI interface 32 bits at 33MHz
•
3.3 volt/ 5.0 volt tolerant PCI signaling
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
GFK-2079
1
Safety Summary
The following general safety precautions must be observed during all phases of the operation,
service, and repair of this product. Failure to comply with these precautions or with specific
warnings elsewhere in this manual violates safety standards of design, manufacture, and intended
use of this product.
GE Fanuc assumes no liability for the customer’s failure to comply with these requirements.
Ground the System
To minimize shock hazard, the chassis and system cabinet must be connected to an electrical
ground. A three-conductor AC power cable should be used. The power cable must either be
plugged into an approved three-contact electrical outlet or used with a three-contact to two-contact
adapter with the grounding wire (green) firmly connected to an electrical ground (safety ground) at
the power outlet.
Do Not Operate in an Explosive Atmosphere
Do not operate the system in the presence of flammable gases or fumes. Operation of any electrical
system in such an environment constitutes a definite safety hazard.
Keep Away from Live Circuits
Operating personnel must not remove product covers. Component replacement and internal
adjustments must be made by qualified maintenance personnel. Do not replace components with
power cable connected. Under certain conditions, dangerous voltages may exist even with the
power cable removed. To avoid injuries, always disconnect power and discharge circuits before
touching them.
Do Not Service or Adjust Alone
Do not attempt internal service or adjustment unless another person, capable of rendering first aid
and resuscitation, is present.
Do Not Substitute Parts or Modify System
Because of the danger of introducing additional hazards, do not install substitute parts or perform
any unauthorized modification to the product. Return the product to GE Fanuc for service and
repair to ensure that safety features are maintained.
GFK-2079
Chapter 1 Introduction, Description, and Specifications
1-3
Chapter
Configuration and Installation
2
This chapter describes the physical installation and configuration of the PMC IDE Hard Disk
Adapter.
The IC697VHD100 is designed to be used within any GE Fanuc SBC system that allows the
installation of a PCI Mezzanine Card (PMC) interface based on the P1386.1 Specification. This
chapter contains step-by-step instructions for the physical installation of the IC697VHD100.
GFK-2079
2-1
2
Physical Installation
1.
The four host mounting screws attached to the IC697VHD100 must be removed before the
board can be installed into the Host chassis. Two of the screws are installed in the
standoffs, located closest to the PMC connectors. The other two are screwed into the
bezel. Remove the four screws (do not remove the screws that hold the bezel and the
standoffs to the PCB board).
Caution
Some of the components assembled on GE Fanuc’s products may be
sensitive to electrostatic discharge, and damage may occur on boards that
are subjected to a high energy electrostatic field. When the board is placed
on a bench for configuring, etc., it is suggested that conductive material be
inserted under the board to provide a conductive shunt. Unused boards
should be stored in the same protective boxes in which they were shipped.
2.
Turn off power to the SBC.
3.
Place the SBC in a position so that the PMC Interface is easily accessible.
4.
With the component side of the IC697VHD100 facing the SBC and oriented such that the
front panel bezel of the PMC board faces the front panel of the SBC, slip the front panel
bezel of the PMC board into the SBC PMC front panel port. See Figure 2-1.
Figure 2-1: Installing the IC697VHD100Board
2-2
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
GFK-2079
2
GFK-2079
5.
Taking care that the PMC alignment pin on the SBC aligns with the alignment hole
located near the PMC connectors in the IC697VHD100, connect the PMC board to the
PMC connectors on the SBC and press until the unit is snug.
6.
Install the screws that were removed from the board in step 1 through the host SBC into
the IC697VHD100 standoffs and bezel. Tighten until secure (do not overtighten). This
step secures the IC697VHD100 to the host SBC.
7.
Re-install the SBC/IC697VHD100 assembly into the Host chassis.
Chapter 2 Configuration and Installation
2-3
2
Connector Pinouts
The IC697VHD100 has several connectors for its I/O ports. Wherever possible, the IC697VHD100
uses connectors and pinouts typical for any desktop PC. This ensures maximum compatibility with
a variety of systems.
PCI Mezzanine Card Connectors
The IC697VHD100 utilizes standard PMC P1 and P2 connectors. Tables 2-1 and 2-2 provide the
pinout and Figure 2-2 illustrates the connector layout and location of pin 1.
Figure 2-2: IC697VHD100 Connector Layout
2-4
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
GFK-2079
2
Table 2-1: P1 Connector Pinout
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
1
NC
17
REQ#
33
FRAME#
49
AD9
2
NC
18
VCC 5.0V
34
GND
50
VCC 5.0V
3
GND
19
VCC IO
35
GND
51
GND
4
INTA#
20
AD31
36
IRDY#
52
C/BE[0]
5
NC
21
AD28
37
DEVSEL#
53
AD6
6
NC
22
AD27
38
VCC 5.0V
54
AD5
7
BUSMODE1#
23
AD25
39
GND
55
AD4
8
VCC 5.0V
24
GND
40
LOCK#
56
GND
9
NC
25
GND
41
NC
57
VCC IO
10
NC
26
C/BE[3]
42
NC
58
AD3
11
GND
27
AD22
43
PAR
59
AD2
12
NC
28
AD21
44
GND
60
AD1
13
CLK
29
AD19
45
VCC IO
61
AD0
14
GND
30
GND
46
AD15
62
VCC 5.0V
15
GND
31
VCC IO
47
AD12
63
GND
16
GNT#
32
AD17
48
AD11
64
NC
Table 2-2: P2 Connector Pinout
Pin
No.
GFK-2079
Signal
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
1
NC
17
NC
33
GND
49
AD8
2
NC
18
GND
34
NC
50
VCC 3.3V
3
NC
19
AD30
35
TRDY#
51
AD7
4
tied to pin 5
20
AD29
36
VCC 3.3V
52
NC
5
tied to pin 4
21
GND
37
GND
53
VCC 3.3V
6
GND
22
AD26
38
STOP#
54
NC
7
GND
23
AD24
39
PERR#
55
NC
8
NC
24
VCC 3.3V
40
GND
56
GND
9
NC
25
IDSEL
41
VCC 3.3V
57
NC
10
NC
26
AD23
42
SERR#
58
NC
11
BUSMODE2#
27
VCC 3.3V
43
C/BE[1]
59
GND
12
VCC 3.3V
28
AD20
44
GND
60
NC
13
RST#
29
AD18
45
AD14
61
NC
14
BUSMODE3#
30
GND
46
AD13
62
VCC 3.3V
15
VCC 3.3V
31
AD16
47
GND
63
GND
16
BUSMODE4#
32
C/BE[2]
48
AD10
64
NC
Chapter 2 Configuration and Installation
2-5
2
Secondary IDE Front Panel Connector
The IC697VHD100 utilizes a standard IDE configuration for the P3 connector. Table 2-3 provides
the pinout and Figure 2-2 illustrates the connector layout and location of Pin 1.
Table 2-3: P3 Connector Pinout
Pin
No.
Pin
No.
Signal
Pin
No.
Signal
Signal
Pin
No.
Signal
1
RESET#
11
DATA3
21
DMARQ
31
INTRQ
2
GND
12
DATA12
22
GND
32
DWORDSIZE#
3
DATA7
13
DATA2
23
DIOW#
33
DA1
4
DATA8
14
DATA13
24
GND
34
CBLIO#
5
DATA6
15
DATA1
25
DIOR#
35
DA0
6
DATA9
16
DATA14
26
GND
36
DA2
7
DATA5
17
DATA0
27
IORDY
37
CS0#
8
DATA10
18
DATA15
28
ALE#
38
CS1#
9
DATA4
19
GND
29
DMACK#
39
ACT#
10
DATA11
20
NC
30
GND
40
GND
1.8 inch Hard Drive Connector
The pin assignments for the P4 connector are shown in Table 2-4. Figure 2-2 illustrates the
connector layout and location of Pin 1.
Table 2-4: P4 Connector Pinout
Pin
No.
2-6
Pin
No.
Signal
Signal
Pin
No.
Signal
Pin
No.
Signal
A1
NC
8
DATA10
21
DMARQ
34
CBLIO#
B1
NC
9
DATA4
22
GND
35
DA0
C1
NC
10
DATA11
23
DIOW#
36
DA2
D1
NC
11
DATA3
24
GND
37
CS0#
E1
NC
12
DATA12
25
DIOR#
38
CS1#
F1
NC
13
DATA2
26
GND
39
ACT#
1
RESET#
14
DATA13
27
IORDY
40
GND
2
GND
15
DATA1
28
GND
41
VCC_3.3V
3
DATA7
16
DATA14
29
DMACK#
42
VCC_3.3V
4
DATA8
17
DATA0
30
GND
43
GND
5
DATA6
18
DATA15
31
INTRQ
44
NC
6
DATA9
19
GND
32
IOCS16#
45
GND
7
DATA5
20
NC
33
DA1
46
GND
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
GFK-2079
Chapter
Theory of Operation
3
The IC697VHD100 is compliant with both the Peripheral Communication Interface (PCI)
Specification 2.1 and PCI Mezzanine Card (PMC) P1386.1 Specification. The PCI Specification
2.1 requires that any interface to the PCI bus contain a PCI Configuration Space Register as shown
in Table 1-1. The registers are located in the configuration space and contain the base addresses of
the four PCI memory windows utilized by the IC697VHD100.
Figure 3-1: IC697VHD100 Functional Block Diagram
32-Bit, 33MHz, PCI Bus
PCI-IDE Bridge
CMD PCI-649
Primary EIDE Channel
Ultra DMA/66
On-Board
Toshiba 1.8-inch
Hard Disk Drive
GFK-2079
Secondary EIDE Channel
up to Ultra DMA/100
40-Pin Header
to External
Disk Drive(s)
3-1
3
Table 3-1 PCI Configuration Space Registers
31
16
15
00
Device ID (00C0h)
Vendor ID (102Ch)
00h
Status
Command
04h
Class Code 03h (Base Class) 00h (Sub Class)
BIST
Header Type
Latency Timer
Revision ID
08h
Cache Line Size
0Ch
PCI Base Address 0 for Memory-Mapped Configuration Registers
10h
Reserved
14h
Reserved
18h
Reserved
1Ch
Reserved
20h
Reserved
24h
Reserved
28h
Reserved
Reserved
3-2
2Ch
PCI Base Address for Expansion ROM BIOS
30h
Reserved
34h
Reserved
Max_Lat
Register
Address
Min_gnt
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
38h
Interrupt Pin
Interrupt Line
3Ch
GFK-2079
Chapter
Maintenance
4
This chapter provides information relative to the care and maintenance of the PMC IDE Hard Disk
Adapter.
If the product malfunctions, verify the following:
•
Software
•
System configuration
•
Electrical connections
•
Jumper or configuration settings
•
Boards fully inserted into their proper connector location
•
Connector pins are clean and free from contamination
•
No components of adjacent boards are disturbed when inserting or removing the board
from the VMEbus card cage
•
Quality of cables and I/O connections
User level repairs are not recommended. Contact your authorized GE Fanuc distributor for a Return
Material Authorization (RMA) Number. This RMA Number must be obtained prior to any
return.
514-000433-000
4-1
Appendix System Driver Software
A
Introduction
The IC697VHD100 is a PMC-based PCI-IDE hard disk drive adapter utilizing the CMD
Technology PCI-649 controller chip. The IC697VHD100 provides an on-board Ultra DMA/66 hard
disk drive on the primary channel and a 40-pin, front-panel accessible connector. The front panel
header allows for the connection of up to two Ultra DMA/66/100 devices on the secondary
channel.
To optimize performance of Ultra DMA/66/100 devices connected to the IC697VHD100, install
the driver software located on the distribution CD-ROM provided with the unit. Instructions for
installation of the drivers during the installation of Microsoft Windows NT 4.0 and Windows 2000
operating systems are provided in the following sections.
GFK-2079
A-1
A
Ultra DMA/66/100 Driver Disk Preparation
The Ultra DMA drivers for Windows NT 4.0 and Windows 2000 are provided on the distribution
CD-ROM. Before attempting the installation of one of these operating systems, the appropriate
driver files must be copied to a blank, user-supplied floppy disk.
To create a Windows NT 4.0 or Windows 2000 driver disk, browse to the \WinNT4\ or \Win2K\
directory respectively on the distribution CD-ROM. Copy all files and folders to a blank floppy
disk and label it ‘CMD CSA-64xx IDE Driver’.
Windows NT 4.0
1.
Begin the installation of Windows NT 4.0 according to the instructions accompanying the
Windows NT installation CD-ROM.
2.
When ‘Setup is inspecting your computer’s hardware configuration’ displays, press F6.
3.
Insert the CMD CSA-64xx IDE Driver disk in the floppy drive.
4.
When prompted to specify additional devices, press S, Enter, Enter. When ‘CMD CSA64xx IDE Driver’ displays, press Enter. After files are copied from the floppy, press Enter
to continue with the installation.
5.
After Windows NT 4.0 is completely installed, copy ‘Cmdcfgnt.exe’ from the driver
floppy to the \winnt\system32 directory. Run the executable to optimize the CMD
controller.
Note
The ‘readme.txt’ file on the driver disk provides additional information about the
installation of the driver.
Windows 2000
1.
Begin the installation of Windows 2000 according to the instructions accompanying the
Windows 2000 installation CD-ROM.
Note
Do not press F6 when prompted to install third-party drivers. The driver will be
installed after Windows 2000 is completely installed.
A-2
2.
Complete the installation of Windows 2000, allowing the host computer to restart as
necessary.
3.
When Windows 2000 is completely installed, right-click on ‘My Computer’ and click
‘Properties.’ Click the ‘Hardware’ tab. Click the ‘Device Manager’ button.
4.
Insert the CMD CSA-64xx IDE Driver disk in the floppy drive.
IC697VHD100 PMC IDE Hard Disk Adapter
Installation Manual – April 2002
GFK-2079
A
5.
Double click on ‘IDE ATA/ATAPI controllers’. Double-click on ‘Standard Dual Channel
PCI IDE Controller’. Click the ‘Driver’ tab. Click the ‘Update Driver’ button.
6.
When the ‘Upgrade Device Driver Wizard’ appears, click ‘Next’. Select ‘Search for a
suitable driver for my device’ and click ‘Next’. Select ‘Floppy disk drives’ and click
‘Next’. When the wizard locates the driver on the floppy disk, click ‘Next’.
7.
Click ‘Yes’, ‘Finish’, ‘Close’.
8.
Click ‘Yes’ to restart the computer.
Note
The ‘readme.txt’ file on the driver disk provides additional information about the
installation of the driver.
GFK-2079
Appendix A System Driver Software
A-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising