ETC® D40 - Times Square Stage Lighting

ETC® D40 - Times Square Stage Lighting
ETC®
D40™
Desire™ Series
D40
D40XT
D60
Vivid™
Lustr®+
Fire™
Ice™
This datasheet covers D40 fixtures as shown.
See other datasheets for other versions.
G E N E R A L I N F O R M AT I O N
O R D E R I N G I N F O R M AT I O N
ETC’s Desire Series D40 fixture puts the seven-color x7 system into
a round theatrical wash light. Highly efficient primary lenses and
careful color choices make the D40 fixture ideal for stage, studio
and anywhere strong color and high-intensity are requirements. The
Selador® x7 Color System™ produces the widest range of spectrallybalanced saturated and tinted color choices available. D40’s rugged
die-cast enclosure, noiseless fan-free operation, multiple lens options
and advanced user interface make it ideal for multiple applications.
Selador D40
D40 LED ARRAY OPTIONS
D40 fixtures are based on the x7 Color System that uses seven
different LED colors to achieve true, usable broad-spectrum color.
The D40 luminaire is available with any one of the following x7 color
arrays (not interchangeable) to best suit the intended application.
MODEL
DESCRIPTION
SELD40VI
D40 Vivid wash fixture – for high-intensity color
mixing across the spectrum for widest color
wash use
SELD40LI
D40 Lustr+ front light wash fixture – optimized
for skin tones and light tints for use as a
theatrical front light
Note: D
40 luminaires ship with hanging yoke, 25° secondary lens and Edison power
input lead. C-clamps are not included.
Other D40 Versions
• D40 Vivid™ – the x7 Color System array balanced for best
all-around use as a color-changing wash fixture
• D40 Lustr®+™ – optimized array with six colors plus high intensity white LEDs to create an ideal front light wash fixture
for full range color, with an emphasis on lighter colors
and white
• D40 Ice™ – uses the cool colors of the x7 System to provide
extra-high brightness color in the blue end of the spectrum
• D40 Fire™ – uses the warm colors of the x7 System to provide
extra-high brightness color in the red end of the spectrum
SELD40FI
D40 Fire special wash fixture – limited palette, high
brightness in the red (warm) end of the spectrum
SELD40II
D40 Ice special wash fixture – limited palette, high
brightness in the blue (cool) end of the spectrum
SELD40 V I – 0X
D40 Model Prefix
Color Mix
V = Vivid 7-color standard wash
L = Lustr+ front light
wash variant
F = Fire variant
I = Ice variant
Usage Rating
I = IP20 (interior)
O = IP66 (exterior)
Finish Options
0 = Black (standard)
1 = White
5 = Silver or other
custom color
(Contact factory)
Connector Options
X = Bare end
A = Parallel blade, U-ground (Edison)
Note – all IP-20 rated fixtures ship
standard with either bare-end power lead
or Edison connector-equipped power lead.
Other power lead options are shown in
the “Power Lead Options” table.
1 of 8
ETC®
D40™
Desire™ Series
S P E C I F I C AT I O N S
A D D I T I O N A L O R D E R I N G I N F O R M AT I O N
GENERAL
• 40 LED color mixing wash fixture
• ETL listed to UL1573 – the standard for stage and studio
lighting units
• IP20-rated for indoor use
• Power and DMX in/thru connections for easy setup
• User-friendly control interface with multiple modes and
fixture settings
PHYSICAL
• Rugged die-cast all-metal housing
• Easy access slots for secondary lenses and standard 7.5”
PAR accessories
• Available in black (standard), white or silver (optional) or
custom colors (contact factory)
• Hanging yoke standard. Optional yoke/floor stand available
ELECTRICAL
• 100VAC to 240VAC 50/60 Hz universal power input
• Neutrik power in and thru connections
• Up to 10 fixtures may be linked via power in/thru connectors
per 15A circuit
• Requires power from a non-dim source
LED*
• 50,000 hour LED life (50,000 hours to 70% intensity)
• 40 Luxeon® Rebel LED emitters
Power Input Cables
Use information below to order 5’ power input leads with factory fitted connectors
DESCRIPTION
DPA-A
5’ PowerCon™ to parallel blade U-ground
(Edison) connector
The above Edison power input lead ships standard with each
fixture. Other leads listed below are available as options.
DPA-B
5’ PowerCon to 20A two pin and ground (stage pin)
connector
DPA-C
5’ PowerCon to grounded 20A twistlock connector
DPA-X
5’ PowerCon to bare-end power input lead
DPA-M
1M Molex to bare end power input lead (XT fixtures
only; not included with fixtures)
Power Thru Jumpers
Note: Power thru jumpers connect to fixture’s output (thru) connector to provide link
to successive fixtures
*See additional LED notes on page three
COLOR
• Exclusive x7 Color System™ seven-color LED array
• Beautifully illuminates skin tones and other objects for
natural appearance and high color rendering
• Broad-spectrum color interacts seamlessly with
conventional sources
• Exclusive optional red-shift option emulates tungsten
dimming performance
OPTICAL
• Primary field angle of 17° and beam angle of 8°
• Secondary lenses available for multiple beam spread options
• Each fixture ships with a 25° lens; additional lenses must
be ordered separately
• Refer to accessories charts for lenses available
CONTROL
• DMX512 in and thru via five-pin XLR connectors
• Multiple control options including RGB, strobe, and console free Master/Slave mode
• See DMX Control Table for additional information
• 15-bit virtual dimming engine provides smooth, high quality
theatrical fades and minimizes color shift during dimming
• RDM functionality for address and setting changes
THERMAL
• Ambient operating temperature of -4° to 104°F (-20° to 40°C)
• Active electronic thermal management for
droop-free operation
• Noiseless, fan-free convection cooling for acoustically
sensitive installations
• Fixture is designed for continuous operation up to 104°F
(40°C) ambient temperature and requires free flow of air
around fixture housing
MODEL
MODEL
DESCRIPTION
DPJ-5
5’ PowerCon to PowerCon™ fixture to
fixture jumper
DPJ-10
10’ PowerCon to PowerCon fixture to
fixture jumper
DPSJ-25
25’ PowerCon to Edison input power cable with
inline switch
Fixtures Accessories
2 of 8
MODEL
DESCRIPTION
SELD40FSY
Yoke with floor stand attachment
400BD
Barn door (Use only as a flexible top hat to diminish
aperture glare. Not for beam shaping)
407CF
Color Frame (use for round and oblong lenses)
400L
Egg Crate Louver
400PTH3
Top Hat 3” Tube
400PTH6
Top Hat 6” Tube
400PHH
Half Hat 6” Tube
400CC
C-Clamp (does not ship with fixture)
400SC
Safety Cable (32”)
ETC®
D40™
Desire™ Series
A D D I T I O N A L O R D E R I N G I N F O R M AT I O N
NOTES ABOUT LED LUMINAIRES
Secondary Lens Options
All LED sources experience some lessening of light output and some
color shift over time. LED output will vary with thermal conditions.
Based on the LED manufacturer’s B50 L70 specification, a Selador
luminaire will achieve ~70% of its initial output after 50,000
hours of typical usage. In individual situations, LEDs will be used
for different durations and at different levels. This can eventually
lead to minor alterations in color performance, necessitating slight
adjustment to presets, cues or programs.
MODEL
DESCRIPTION: The following lenses are cut for
D40 fixtures and create round, linear or oblong
field patterns as described below. These lenses
are not sized for use in Selador® Classic (Vivid™,
Lustr®, Paletta™, etc.) fixtures.
Narrow
Linear Field
Note: This is the same material as Selador Classic
lenses
SELL20-7.5
7.5” 20° lens (narrow linear field)
SELL30-7.5
7.5” 30° lens (narrow linear field)
SELL40-7.5
7.5” 40° lens (narrow linear field)
SELL60-7.5
7.5” 60° lens (narrow linear field)
SELL80-7.5
7.5” 80° lens (narrow linear field)
Linear lenses
may be
combined
to create
desired field
size, i.e.
40° X 60°
C R I A N D C Q S R AT I N G S
Desire fixtures were evaluated for CRI and CQS performance using
measured output spectrum and optimized mix solutions for a best
spectral match to black body sources at 3200K and 5600K.
Fixture
CRI
CQS
Color
Fidelity
Duv
7.5” 25° lens (round field)
D40 Vivid™ at 3200K
87
89
89
0.000
7.5” 35° lens (round field)
D40 Vivid at 5600K
90
92
92
0.000
7.5” 45° lens (round field)
D40 Lustr+ at 3200K
86
88
88
0.000
7.5” 75° lens (round field)
D40 Lustr+ at 5600K
93
92
90
0.000
D40 Studio HD at 3200K
89
90
91
0.000
D40 Studio HD at 5600K
92
94
94
0.000
D40 Studio Daylight
at 5600K
71
70
69
0.001
D40 Studio Tungsten™
at 3000K
86
86
86
0.001
Round Field
SELR25-7.5
SELR35-7.5
SELR45-7.5
SELR75-7.5
™
-
Oblong Field
SELO2040-7.5
7.5” 20° x 40° lens (oblong field)
SELO3070-7.5
7.5” 30° x 70° lens (oblong field)
SELO3580-7.5
7.5” 35° x 80° lens (oblong field)
™
All D40 luminaire versions provide excellent color rendering to the
eye, particularly at higher color temperature settings such as 5600K.
In most cases the Duv is 0.000. A Duv rating of 0.000 indicates that
the color mix used is exactly on the black body line, with no green or
magenta tint.
Typical Lens Field Profiles
Narrow Linear
™
Round
Oblong
Power Consumption at Full Intensity
MODEL
VOLTAGE
(V)
CURRENT
(A)
WATTS
D40
120 / 240
1 / .5
110
3 of 8
ETC®
D40™
Desire™ Series
CONTROL OPTIONS
CONTROL OPTIONS
User settings on D40 fixtures allow multiple operational modes and
settings for either console operation via DMX protocol or stand-alone
operation. The expanded LCD display provides easy navigation to all
possible settings and options. Some of the setting options are:
• Multiple DMX choices ranging from a simple RGB
profile – which effectively controls all seven LED colors via
three channels – to nine-channel ‘direct’ color and
intensity control
• Multiple dimming curve options
• Preset colors and sequences for stand-alone (no console
required) operation
• White point selection – white light and color behavior based
on a specific color temperature white light, i.e. 3200K,
5600K, etc
• Loss of data behavior options – instant off, hold last look for
two minutes, etc
• Output modes – three output options that offer the user a
choice between maximum output and maximum consistency
See the user manual for a complete explanation of all of the control
settings and options for the D40.
DMX Input Channel Profiles
DMX
Profile
DMX
Channels
Channel
Assignments
Direct
9
1 – Red
2 – Orange
(white if Lustr+)
3 – Amber
4 – Green
5 – Cyan
6 – Blue
7 – Indigo
8 – Intensity
9 – Strobe
Direct control of each individual
color with a separate master
intensity channel. Color
calibration of LEDs is not active
in this mode. The nine-channel
profile will produce the highest
quality color cross-fades.
HSI
5
1 – Hue (coarse)
2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
High resolution hue (twochannels), saturation, and
intensity control. HSI mode will
produce arbitrary color crossfades around the color space.
HSIC
6
1 – Hue (coarse)
2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
6 – Color Point
(CCT)
High-resolution hue, saturation
and intensity control as above,
with the addition of a color
point channel to adjust the color
temperature of the fixture in both
white light and color. Color crossfade performance is the same
as HSI.
RGB
5
(Ch. 4
not used)
1 – Red
2 – Green
3 – Blue
4 – n/a
5 - Strobe
Effectively addresses all seven
colors via three channels of
control. RGB profile will produce
medium quality color cross-fades
1 – Intensity
2 – Color Point
(CCT)
3 – Tint
Controls fixture as a white light
unit. If no DMX, i.e. console
input, is present, fixture can
be adjusted for these three
parameters on the U/I at the back
of the unit.
Quick Setups
To assist in managing the numerous control and fixture behavior choices, five
combinations of operational settings are available to quickly get started. These
settings are specifically created for different applications and are easily accessible at
the fixture display. Each setting can then be modified as required to take advantage
of all of the possible control features.
Setting
Title
Profile
General
Direct
Factory Default:
For general purpose
use including interior
architectural applications
• Standard dimming curve
• Regulated output for
color consistency
Stage
HSI
Plus 7
Enabled
Theatrical lighting:
Duplicates the color and
dimming behavior of
tungsten stage lighting
fixtures.
• Incandescent dimming
curve
• Regulated output for
color consistency
• 3250K white point setting
HSI
Exterior Architectural lighting:
Provides a high degree
of color consistency in
high ambient temperature
environments.
• Standard dimming curve
• Protected output
• 3200K white point setting
Event lighting:
Enables quickest response,
simple RGB control and
strobe channel for maximum
effect usage
• Quick dimming curve
• Boost mode for
maximum intensity
• 5600K white point setting
Studio Factory Default:
Enables three parameter
control of white light
(intensity, white point, and
tint) via DMX from console
or from fixture display – no
console required
• Linear dimming curve
• Regulated output mode
for color consistency
XT Arch
High
Impact
RGB
Studio
Studio
Description
Typical Features*
Studio
3
Notes
Additional profile options
Plus 7
Seven additional color control channels are available
in RGB, HSI, HSIC, and Studio profile settings.
For example HSI with ‘Plus 7’ enabled becomes a
14-channel profile:
1 – Hue (coarse)
2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
6 – n/a
7 – Plus 7
Control on/off
8 – Red
9 – Orange
(white if Lustr+)
10 – Amber
11 – Green
12 – Cyan
13 – Blue
14 – Indigo
The desired color and intensity
is achieved by using the HSI or
RGB channels.
Placing channel seven at a value
over 51% gives the fixture a
14-channel profile.
Channels 8-14 represent the
native colors of the fixture and
allow the operator to adjust
individual color channels to fine
tune the color output.
*See user manual for complete list of features for each Quick Setup
Strobe
4 of 8
Variable strobe control: 0% is no strobe. The fixture
output will strobe more rapidly as the strobe channel
value approaches 100%.
ETC®
D40™
Desire™ Series
PHOTOMETRICS
Cosine Candela Plot
D40 Vivid™
Degree
Candela
Field
Lumens
Beam
Lumens
Lumens
Per Watt
Boost - Cold
17˚
101,900
2,540
1,200
26.7
Regulated
17˚
87,200
2,150
1,020
26.5
120000
100000
80000
Candela
Mode
X
60000
Y
40000
Metric Conversions: For Meters multiply feet by .3048
For Lux multiply footcandles by 10.76
20000
0
-15
-10
-5
0
5
10
15
17˚
Field Angle
8˚
Beam Angle
Degrees
Iso-Illuminance Diagram
(Flat Surface Distribution)
Y
Throw Distance (d)
10’
3.0m
15’
4.6m
20’
6.1m
25’
7.6m
319’
97m
Field Diameter
3.1’
0.9m
4.6’
1.4m
6.2’
1.9m
7.7’
2.3m
– Illuminance (fc)
1,019
453
255
163
1
Illuminance (lux)
10,968
4,875
2,742
1,755
10.76
10%
50%
% illuminance
foot candle
or lux
X
For field diameter at any distance, multiply distance by .308
For beam diameter at any distance, multiply by 0.145
.056
D40 Lustr+™
.167
Cosine Candela Plot
Degree
Candela
Field
Lumens
Beam
Lumens
Lumens
Per Watt
Boost - Cold
17˚
121,500
2,980
1,450
30.3
Regulated
17˚
109,100
2,680
1,300
29.8
120000
100000
80000
Candela
Mode
.111
X
60000
Y
40000
Metric Conversions: For Meters multiply feet by .3048
For Lux multiply footcandles by 10.76
20000
0
-15
-10
-5
0
5
10
15
17˚
Field Angle
8˚
Beam Angle
Degrees
Iso-Illuminance Diagram
(Flat Surface Distribution)
Y
Throw Distance (d)
10’
3.0m
15’
4.6m
20’
6.1m
25’
7.6m
348’
106m
Field Diameter
3.0’
0.9m
4.5’
1.4m
6.0’
1.8m
7.5’
2.3m
– Illuminance (fc)
1,215
540
304
194
1
Illuminance (lux)
13,078
5,813
3,270
2,093
10%
50%
% illuminance
foot candle
or lux
X
10.76
For field diameter at any distance, multiply distance by .301
For beam diameter at any distance, multiply by 0.145
.056
5 of 8
.111
.167
ETC®
D40™
Desire™ Series
PHOTOMETRICS
Cosine Candela Plot
D40 Fire™
90000
Degree
Boost - Cold
Regulated
Candela
17˚
94,900
17˚
82,500
Field
Lumens
Beam
Lumens
Lumens
Per Watt
2,540
1,200
28.7
80000
70000
60000
Candela
Mode
100000
X
50000
Y
40000
30000
2,220
1,040
27.7
20000
10000
Metric Conversions: F or Meters multiply feet by .3048
For Lux multiply footcandles by 10.76
-10
-5
0
5
10
15
Iso-Illuminance Diagram
Field Angle
17˚
-15
Degrees
Beam Angle
8˚
0
(Flat Surface Distribution)
Y
10%
Throw Distance (d)
10’
3.0m
15’
4.6m
20’
6.1m
25’
7.6m
308’
93m
Field Diameter
3.2’
1.0m
4.8’
1.5m
6.4’
1.9m
8.0’
2.4m
– Illuminance (fc)
949
422
237
152
1
10,215
4,540
2,554
1,634
10.76
Illuminance (lux)
50%
% illuminance
foot candle
or lux
X
For field diameter at any distance, multiply distance by .318
For beam diameter at any distance, multiply by 0.148
.056
D40 Ice™
.167
Cosine Candela Plot
Degree
Candela
Field
Lumens
Beam
Lumens
Lumens
Per Watt
Boost - Cold
17˚
70,900
1,830
890
18.1
Regulated
17˚
63,200
1,630
790
18.0
70000
60000
50000
40000
Candela
Mode
.111
X
Y
30000
Metric Conversions: For Meters multiply feet by .3048
For Lux multiply footcandles by 10.76
20000
10000
17˚
Field Angle
8˚
Beam Angle
0
-15
-10
-5
0
5
10
15
Degrees
Iso-Illuminance Diagram
(Flat Surface Distribution)
Throw Distance (d)
10’
3.0m
15’
4.6m
20’
6.1m
30’
9.1m
266’
81m
Field Diameter
3.1’
.9m
4.6’
1.4m
6.2’
1.9m
9.3’
2.8m
– Illuminance (fc)
Illuminance (lux)
Y
10%
709
315
177
78.78
1
7,632
3,392
1,908
848
10.76
50%
For field diameter at any distance, multiply distance by .310
For beam diameter at any distance, multiply by 0.147
% illuminance
foot candle
or lux
X
Throw Distance Multiplier (TDM)
To determine the distance from the center of the beam (Origin) to a certain illuminance level at a particular
distance, multiply the desired throw distance by the TDM desired on the Iso-Illuminance diagram.
Throw Distance (TD) x Throw Distance Multiplier (TDM) = Distance from the Origin (DfO) (distance from the center
of the beam)
Example: 25 feet (TD) x 0.047 (TDM) = 1.175 feet from center of beam (DfO)
For illumination with any lamp, multiply the candlepower of a beam spread by the multiplying factor (mf) shown for that lamp.
To determine illumination in footcandles or lux at any throw distance, divide candlepower by distance squared.
6 of 8
.056
.111
.167
ETC®
D40™
Desire™ Series
PHYSICAL
Selador D40 Weights and Dimensions
WEIGHT*
SHIPPING WEIGHT
lbs
kgs
lbs
kgs
14
6.4
17
7.8
* Does not include mounting hardware
19.3”
490mm
14.8”
375mm
11.7”
300mm
13.3”
340mm
8.3”
210mm
4.5”
115mm
4.2”
105mm
5.7”
145mm
6.4”
165mm
10.4”
265mm
7 of 8
8.5”
215mm
9.2”
235mm
10.6”
270mm
ETC®
D40™
Desire™ Series
Corporate Headquarters • 3031 Pleasant View Rd, PO Box 620979, Middleton WI 53562 0979 USA • Tel +1 608 831 4116 • Fax +1 608 836 1736
London, UK • Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK • Tel +44 (0)20 8896 1000 • Fax +44 (0)20 8896 2000
Rome, IT • Via Pieve Torina, 48, 00156 Rome, Italy •Tel +39 (06) 32 111 683 • Fax +44 (0)20 8752 8486
Holzkirchen, DE • Ohmstrasse 3, 83607 Holzkirchen, Germany • Tel +49 (80 24) 47 00-0 • Fax +49 (80 24) 47 00-3 00
Hong Kong • Room 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong • Tel +852 2799 1220 • Fax +852 2799 9325
Web • www.etcconnect.com • Copyright©2012 ETC. All Rights Reserved. All product information and specifications subject to change. 7410L1001 Rev. G USA 02/12
This product is protected by one or more of the following U.S. Patents: 6,016,038, 6,150,774, 6,788,011, 6,806,659, 6,683,423 and 7,023,543
8 of 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising