De'Longhi DL48P6G-E User's Manual

De'Longhi DL48P6G-E User's Manual
DUAL FUEL SELF CLEANING RANGE
for residential use only
Models:
DL 48 P6G
DL 48 P6GE
• INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
✓ Before beginning, please read these instructions completely and carefully.
✓ Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
✓ Please observe all local and national codes and ordinances.
✓ Please ensure that this product is properly grounded.
✓ The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with
the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part
280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on steel and aluminium parts.
This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
WARNING
• ALL RANGES CAN TIP
• INJURY TO PERSON COULD RESULT
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
• SEE INSTALLATION INSTRUCTIONS
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
✓ Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
✓ WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• lmmediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• lf you cannot reach your gas supplier, call the fire department.
✓ Installation and service must be performed by a qualified installer,
service agency, or the gas supplier.
2
DATA PLATE
CONVERSION LABEL
This appliance is designed and manufactured solely for the cooking of domestic (household)
food and in not suitable for any none domestic application and therefore should not be used
in a commercial environmement.
The appliance guarantee will be void if the appliance is used within a none domestic
environmement i.e. a semi commercial, commercial or communal environment.
3
INSTALLATION INSTRUCTIONS
WARNING!
THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a
qualified installer, service agent, or the gas supplier.
IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
TOOLS NEEDED FOR INSTALLATION
4
Screwdriver
2 - Wrench
Suitable protective
gloves
Hammer
T-handle
wrench
Pencil
Adjustable
wrench
Adjustable
pliers
Tape
measure
Drill
GENERAL INFORMATION
1. Installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1-Latest Edition.
2. Installation in manufactured (mobile) home: installation
must conform with the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part 3280 [formerly
the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD (Part 280)] or, when such standard
is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes
where applicable.
3. Installation in Recreational Park Trailers: installation must
conform with state or other codes or, in the absence of
such codes, with the Standard for Recreational Park
Trailers, ANSI A119.5.
4.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
The range must be electrically grounded in accordance
with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA No. 70-latest edition.
Installation should be made by a Iicensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
If an external electrical source is utilized, the installation must
be electrically grounded in accordance with local codes or, in
the absence of local codes, with the national Electrical Code,
ANSI/NFPA 70.
WARNING!!
This appliance shall not be used for space heating. This
information is based on safety considerations.
5. AlI openings in the wall behind the appliance and in the floor
under the appliance shall be sealed.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing
service on the range. Replacement parts are available from
factory authorized parts distributors. Contact the nearest parts
distributor in your area.
6. Keep appliance area clear and free from combustible
materials, gasoline, and other flammable vapors.
7. Do not obstruct the flow of combustion and ventilation air.
8. Disconnect the electrical supply to the appliance before
servicing.
9. When removing appliance for cleaning and/or service;
A. Shut off gas at main supply.
B. Disconnect AC power supply.
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward.
CAUTION: Range is heavy; use care in handling.
10. Electrical Requirement
Electrical installation should comply with national and local
codes.
11. Air Supply and Ventilation
The installer must refers to local/national codes.
12. Gas Manifold Pressure
Natural gas - 4.0” W.C.P.
LP/Propane - 11.0” W.C.P.
13. The misuse of oven door (e.g. stepping, sitting, or leaning
on them) can result in potential hazards and/or injuries.
14. When installing or removing the range for service, a rolling
lift jack should be used. Do not push against any of the
edges of the range in an attempt to slide it into or out of
the installation. Pushing or pulling a range (rather than using
a lift jack) also increases the possibility of bending the leg
spindles or the internal coupling connectors.
5
installation
PROXIMITY TO SIDE CABINETS
1. This range may be installed directly adjacent to existing 36"
(914 mm) high base cabinets.
Range dimensions:
• width: 47” 7/8 (1216 mm)
• depth: 23” 15/16 (608 mm)
• height (with backguard): MIN 44” 1/16 (1118 mm) - MAX 44”
1/2 (1130 mm)
• height (with island trim): MIN 39” 1/64 (991 mm) - MAX 39”
1/2 (1003 mm)
• backguard (height): 8” (203 mm)
• island trim (height): 3” (76 mm)
Gas line opening:
Wall - 21 /32” (16.5 mm) from the left/right sides to centre of
range; from 4” 7/32 (107 mm) to 4" 11 /16 (119 mm) [depending on feet regulation] from the floor. This area can be extended on left/right sides: 15" 3/4 (400 mm) from the floor; 2"
51/64 (71 mm) toward centre of range.
Grounded outlet:
Same as per gas line opening.
2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (914 mm) high.
There must be a minimum of 11” 13/16 (300 mm) side clearance from the range to such combustible surfaces TO THE
LEFT or TO THE RIGHT above the 36” (914 mm) high countertop.
IMPORTANT: One side (left or right) above the 36” (914
mm) high countertop must always be kept clear.
Installation with island trim: There must be a minimum of 12”
(305 mm) clearance from the back of the island trim to such
combustible surface on the back of the range above the 36”
(914 mm) high countertop.
3. The maximum upper cabinet depth recommended is 13” (330
mm). Wall cabinet above the range must be a minimum of 30”
(762 mm) above the countertop for a width of minimum 47”
7/8 (1216 mm): it has to be centred with the range. Side wall
cabinets above the range must be a minimum of 18” (457
mm) above the countertop.
(76 mm)
3"
MIN 36" 1/64 (915 mm)
23"
(60 15/16
8m
m)
MAX 36" 1/2 (927 mm)
8"
MIN 36" 1/64 (915 mm)
Island trim
23"
(60 15/16
8m
m)
MAX 36" 1/2 (927 mm)
(203 mm)
Backguard
7/8
7/8
47"
m)
6m
(121
Fig. 1.1a
6
47"
m)
6m
(121
Fig. 1.1b
GAS AND ELECTRIC CONNECTION
Rif.
inch
mm
A
15” 3/4
400
B
2” 51/64
71
C
21/32”
16.5
D
4” 7/32 - 4” 11/16 (*)
107 - 119 (*)
* : Depending on feet regulation
Dotted line showing the position
Area for GAS and ELECTRIC connection
C
B
C
B
D
A
Fig. 1.2
7
PROXIMITY TO SIDE CABINETS
13" max.
(330 mm)
30" min.
(762 mm)
11" 13/16
min. (300
mm)
18" min.
(457 mm)
RANGE WITH BACKGUARD
36"
(914 mm)
20" min
. (500 m
m)
0"
(0 mm
. (500 m
(0 mm
11" 13/16
min. (300
)
mm)
m)
36"
(914 mm)
20" min
0"
30 m m )
18" min.
(457 mm)
30" min.
(762 mm)
13" max. (3
)
0"
m)
(0 m
0"
8
(0 m m
)
Fig. 1.3b
Fig. 1.3a
13" max. (3
PROXIMITY TO SIDE
CABINETS
30 m m )
min
. (30
5m
18" min.
(457 mm)
12"
30" min.
(762 mm)
RANGE WITH ISLAND TRIM
m)
00 mm)
6 min. (3
/1
3
1
"
1
1
36"
(914 mm)
)
(500 mm
.
in
m
"
20
0"
m)
(0 m
Fig. 1.3c
0"
)
11" 13/16
min. (300
mm)
(330 mm)
30" min.
(762 mm)
13" max.
18" min.
(457 mm)
12 "
min
5m
. (30
m)
20" min
.(
500 mm
)
36"
(914 mm)
(0 mm
0"
(0 mm
)
0"
Fig. 1.3d
(0 mm
)
9
ASSEMBLING THE BACKGUARD
OR THE ISLAND TRIM
It is mandatory to install the
backguard or the island trim
A
• Assemble the backguard or the island trim as
shown in figure 1.4 or 1.5 and fix it by screwing the 5 screws “A”.
A
Fig. 1.4
A
A
Fig. 1.5
10
LEVELLING THE RANGE
The range is equipped with 6 LEVELLING FEET (already fitted on the appliance) and
may be levelled by screwing or unscrewing the feet (fig. 1.9).
It is important to observe the prescriptions of figures 1.6, 1.7, 1.8.
Fig. 1.6
Supplied with the range
in a separate kit
0 mm
0"
+ 5/16"
+ 8 mm
+ 5/16"
+ 8 mm
Fig. 1.7
+ 15/32"
+ 12 mm
Fig. 1.8
Fig. 1.9
11
YOU MUST USE STABILITY
ANTI TIP BRACKET TO
PREVENT UNIT FROM
TIPPING.
ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS
1. The anti-tip bracket has to be attached as shown on figure below (only rear central
position), it has to be fixed on the floor and on the rear wall by no. 4 (four) suitable
screws (not supplied).
2. After fixing the anti-tip bracket, slide range into place. Be sure the rear central foot
slides under the anti-tip bracket attached.
Dotted line showing the position
of the range when installed
=
ANTI-TIP STABILITY
DEVICE FIXING
=
Anti-tip
stability device
Rear central
feet of range
Fig. 1.10
12
gas connection
All gas connections must be made according to national and local codes. This gas
supply (service) line must be the same size or greater than the inlet line of the
appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane
gas.
The range is equipped for the use with NATURAL gas. It is design-certified by CSA
International for NATURAL and L.P. gases with appropriate conversion.
The model/serial rating plate, located on the back of the appliance, has information
on the type of gas that can be used. If this information does not agree with the type
of gas available, check with the local gas supplier. See page from 17 to 22 for L.P.
gas conversion instructions.
Explosion Hazard
Use a new CSA or UL approved
gas supply line.
1. Manual Shut-off Valve
(fig. 2.1):
The supply line shall be equipped with an approved shutoff valve. This valve should
be located in the same room as the range and should be in a location that allows
ease of opening and closing (in a position where it can be reached quickly in the
event of an emergency).
Do not block access to the shutoff valve. The valve is for turning on or shutting off
gas to the appliance.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure gas pressure does not exceed 14" water
column.
Examples of a qualified person
include licensed heating personnel, authorized gas company personnel, and authorized
service personnel.
Shutoff valve
“open” position
Failure to do so can result in
death, explosion, or fire.
To range
Gas supply line
Fig. 2.1
2. Pressure Regulator:
a) All heavy duty, commercial type cooking equipment must have a pressure regulator
on the incoming service line for safe and efficient operation, since service pressure
may fluctuate with local demand.
Before installing the regulator mount the 1/2” NPT (conical) male connector to the
regulator (see picture 2.2a). Gasket supplied have to be placed between 1/2” NPT
(conical) connector/extension pipe male pipe fitting (see picture 2.2b).
The regulator supplied with this range must be installed before any gas connections
are made.
Use supplied pressure regulator only.
13
PRESSURE REGULATOR INSTALLATION
STEP 1
Mount the 1/2” NPT (conical) male connector to the pressure
regulator and tighten by using a wrench.
Do not over tighten the connector.
Over tightening may crack regulator.
LOCK
Arrow
Fig. 2.2a
STEP 2
Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The
regulator cover must be oriented toward the front side of the range.
IMPORTANT: use two spanners to tighten the connection.
Regulator cover
14
Fig. 2.2b
GAS CONNECTION SPECIFICATION
Range
manifold
Manifold male pipe fitting
1/2” G cylindrical
(ISO 228-1) male
Gasket
1/2” G cylindrical
(ISO 228-1) female
To range
Extension
Extension
pipe female
pipe
pipe fitting
fitting
Extension
pipe
Extension
pipe male
pipe fitting
1/2” G cylindrical
(ISO 228-1) male
Gasket
1/2” G cylindrical
(ISO 228-1) female
1/2” NPT (conical)
male
Connector
1/2” NPT
female
To mains
connection
Pressure
regulator
1/2” NPT
female
Arrow
WARNING: check the right positioning
of the gas regulator. The arrow on the
back of the gas regulator must be
oriented toward the connector.
Fig. 2.3
15
b) Any conversion required must be performed by your dealer or a qualified licensed
plumber or gas service company. Please provide the service person with this
manual before work is started on the range. (Gas conversions are the responsibility
of the dealer or end user.)
c) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from
the factory adjusted for use with NATURAL gas.
TEST POINT ADAPTER
The Test Point adapter is available from
the After-Sales Service.
d) Manifold pressure should be checked with a manometer and by operating as below
detailed:
- Remove the injector from the front left burner and mount the proper test point
adapter which is available from the After-Sales Service (see side figure and the
“OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS”
chapter).
- Turn the front left burner control knob to the maximum position (
position)
- Press the knob and keeping it pressed check the manifold pressure with a
manometer; NATURAL gas requires 4.0” W.C.P. and LP/PROPANE requires 11.0”
W.C.P.
- Incoming line pressure upstream from the regulator must be 1” W.C.P. higher
than the manifold pressure in order to check the regulator.
- The regulator used on this range can withstand a maximum input pressure of
1/2 PSI (14.0” W.C.P). If the line pressure is in excess of that amount, a stepdown regulator will be required.
e) The appliance, its individual shut-off valve, and pressure regulator must be
disconnected from the gas supply piping system during any pressure testing of
that system at pressures in excess of 1/2 PSI (3.5 kPa).
f) The appliance must be isolated from the gas supply piping system by closing its
individual manual shut-off valve during any pressure testing of the gas supply
piping system at test pressure equal to or less than 1/2 PSI (3.5 kPa).
3. Flexible Connections:
If local codes permit, CSA design-certified, flexible metal appliance connector is
recommended for connecting this range to the gas supply line. Do Not kink or damage
the flexible connector when moving the range. The pressure regulator has 1/2" NPT
female pipe threads.You will need to determine the fittings required, depending on
the size of your gas supply line, flexible metal connector and shutoff valve.
Fig. 2.4
4. Rigid Pipe Connections:
If rigid pipe is used as a gas supply line, a combination of pipe fittings must be used
to obtain an in-line connection to the range. All strains must be removed from the
supply and fuel lines so range will be level and in line.
• Use joint compounds and gaskets that
propane gas on all male pipe threads.
are resistant to action of natural or
• Do not over tighten gas fitting when attaching to pressure regulator. Over
tightening may crack regulator.
5. Leak Testing:
IMPORTANT: Leak testing of the appliance shall be conducted as follows:
• After final gas connection is made, turn on manual gas valve and test all
connections in gas supply piping and appliance for gas leaks with a soapy water
solution. During this test all appliance gas valves have to be closed.
• In order to avoid property damage or serious personal injury, never use a Iighted
match. If a leak is present, tighten joint or unscrew, apply more joint compound,
tighten again and retest connection for leak.
16
CONVERSION TO LP/PROPANE GAS
Every range is provided with a set of injectors for the various types of gas.
Select the injectors to be replaced according to the “INJECTORS TABLE”.
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the
body of each injector.
SETTING THE PRESSURE REGULATOR
(fig. 2.5)
The pressure regulator is accessible by removing the left warmer drawer; the pressure
regulator is positioned on the rear left side of the range.
To remove the warming drawer:
1. Open the drawer completely (fig. 2.5)
2. Move down the lever of left guide (fig. 2.6) and up the lever of right guide (fig. 2.7).
3. Remove the drawer; the levers have to be keep moved (fig. 2.5).
Fig. 2.7
2
3
2
Fig. 2.6
Fig. 2.5
17
To set the pressure regulator (fig. 2.8):
1. Unscrew the regulator cover;
2. Unscrew the A component, reverse and screw it according to the LP/PROPANE
regulation.
Pressure
regulator
REGULATOR COVER
Fig. 2.8
1
2
A
NATURAL GAS
REGULATION
Fitting the warming drawer (fig. 2.9):
1. Insert the drawer guides into the range guides (fig. 2.9)
2. Gently close the drawer completely; the safety catchs will be automatically hooked.
Fig. 2.9
18
LP/PROPANE
REGULATION
INJECTORS TABLE
NOMINAL POWER
REDUCED POWER
BTU/hr
BTU/hr
LP/PROPANE
11” W.C.P.
NATURAL GAS
4” W.C.P.
BURNERS
Ø injector
By-pass
Ø injector
By-pass
[1/100 mm]
[1/100 mm]
[1/100 mm]
[1/100 mm]
Rapid (R)
10000
2000
94
42
155
adjustable
Triple ring (TC)
12000
5000
102
65
170
adjustable
55
27
Inner crown
2800
3500
for NATURAL GAS (*)
16000
15000
for NATURAL GAS (#)
1000 (*)
for LP/PROPANE GAS (*)
(no. 1 central)
80
(no. 1 central)
adjustable
Dual (D)
Outer crowns
Griddle
6500
4500
for LP/PROPANE GAS (#)
12000
72
for NATURAL GAS (#)
(no. 2 outer)
for LP/PROPANE GAS (#)
5000
105
130
60
(no. 2 outer)
65
175
adjustable
adjustable
(*) Power calculated only with inner crown operating
(#) Power calculated with inner and outer crowns operating
OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING
THE INJECTORS (Rapid, triple ring and dual burners)
✓ Remove the gratings and the burner covers;
✓ Using a wrench substitute the nozzle injectors “J” (figs. 2.10a - 2.10b - 2.10c) with
those most suitable for the kind of gas for which it is to be used.
The burner are conceived in such a
way so as not to require the regulation
of the primary air.
Triple ring
burner
Rapid
burner
J
J
Fig. 2.10b
Fig. 2.10a
DUAL
burner
J
Injector for inner crown
J
Injectors for
outer crowns
Fig. 2.10c
19
OPERATIONS TO BE EXECUTED FOR THE
REPLACEMENT OF THE INJECTOR OF THE
GRIDDLE BURNER
B
Fig. 2.11
■
Lift and remove the griddle stainless steel plate.
■
Unscrew the no. 2 (two) screws and remove the plate "B"
(fig. 2.11).
■
Unscrew the no. 2 (two) screws and remove the shield
"P" (fig. 2.12).
■
Unscrew the no. 4 (four) screws and remove the no. 4
(four) clips "S" (fig. 2.13).
■
Unscrew the no. 2 (two) screws and remove the
thermocouple protection "T" (fig. 2.14).
■
Unscrew the no. 2 (two) burner front fixing screws (fig.
2.15).
■
Gently unlock the safety valve probe "V" and the ignition
electrode "I" (fig. 2.16). Take care not to damage the probe
and the ignition electrode.
S
P
Fig. 2.12
Fig. 2.13
T
V
I
Fig. 2.14
20
Fig. 2.15
Fig. 2.16
■
Remove the burner as shown in figure 2.17.
■
Using a 7 mm box spanner, unscrew the injector
(indicated by the arrow in fig. 2.18) and replace it by the
proper one according to the kind of gas.
■
Then replace the burner and other components repeating
the above steps in reverse order.
IMPORTANT: Pay special attention to replace correctly
the safety valve probe "V" and the ignition electrode "I"
as per figures 2.19 and 2.20. Check the correct operation
of the safety valve and the ignition electrode.
Fig. 2.17
Fig. 2.18
Fig. 2.19
Fig. 2.20
I
V
Anchorage
clip
V
I
Anchorage
clip
21
SETTING THE BURNER MINIMUM
F
When switching from one type of gas to another, the minimum flow rate must also be
correct: the flame should not go out even when passing suddenly from maximum to
minimum flame.
To regulate the flame follow the instructions below:
Rapid, triple ring and griddle burners
–
–
–
–
Fig. 2.21
Light the burner
Set the gas valve to
position
Remove the knob
With a thin screwdriver pass by the hole of microswitch and turn the screw F until
adjustment is correct (fig. 2.21).
Inside crown of DUAL burner
H
–
–
–
–
Light the DUAL burner
Set the gas valve to
position
Remove the knob
Using a screwdriver turn the screw H until the correct setting is obtained (fig. 2.22).
G
Outside crowns of DUAL burner
–
–
–
–
Light the DUAL burner
Set the gas valve to
position
Remove the knob
Using a screwdriver turn the screw G until the correct setting is obtained (fig. 2.22).
For LP/PROPANE gas, tighten the adjustment screws completely.
Fig. 2.22
After regulation repeat the operations indicated in paragraph “2. Pressure regulator” at
page 13.
If the range has been disconnected and then connected again to the gas supply line
repeat the operations indicated in paragraph “5. Leak Testing” at page 16.
IMPORTANT:
After conversion to LP/PROPANE gas has been carried out affix on the back of the
appliance, near the data plate, the conversion label supplied and also affix a conversion
label at page 3 of this instruction manual.
22
electrical connection
ELECTRICAL REQUIREMENTS
• This appliance must be properly installed and grounded by a qualified technician in
accordance with the National Electrical Code ANSI/NFPA No.70 (latest edition) and
local electrical code requirements. IN CANADA: Electrical installation must be in
accordance with the current CSA C22.1 Canadian Electrical Codes Part1 and/or local
codes.
• This appliance may be connected by means of permanent “Hard Wiring” or “Power
Supply Cord”. Power supply cord is not supplied, but it is available through your local
electric supply house.
WARNING
TO AVOID ELECTRICAL SHOCK
HAZARD, BEFORE INSTALLING THE
APPLIANCE, SWITCH POWER OFF AT
THE SERVICE PANEL AND LOCK THE
PANEL TO PREVENT THE POWER
FROM BEING SWITCHED ON
ACCIDENTALLY.
• The range must be connected to the proper electrical voltage and frequency as specified on the rating plate.
• The range can be connected directly to the fused disconnect (or circuit breaker box)
through flexible, armoured or non-metallic sheathed, copper cable (with grounding
wire). Allow two to three feet of slack in the line so that it can be moved if servicing
is ever necessary.
ELECTRICAL CONNECTION WITH POWER CORD
Use a 3-wire power supply cord kit rated for 40 amps - 120/240 volts with closed loop
terminals and marked for use with ranges. Where local codes do not permit grounding
through neutral, use a 4-wire power supply cord.
The CSA/UL-listed cord must be secured to the range with the strain relief bracket. The
electrical connection is made at the terminal block, which is located behind the access
door on the back of the range.
ELECTRICAL CONNECTION WITH CONDUIT
Use 1/2” (1.3 cm) trade size CSA/UL-listed conduit with a conduit clamp, 12 AWG/600
volt copper conductor colored red for line 1 and black for line 2 and 12 AWG/600
volt copper conductor (or 10 AWG/600 volt copper conductor if grounding through
neutral) colored white for neutral with closed loop terminals marked for use with ranges.
Where local codes do not permit grounding through neutral, use a green 10 AWG copper conductor as directed in the 4-wire connector directions. The conduit must be
secured to the range with the strain relief bracket. The electrical connection is made at
the terminal block which is located behind the access door on the back of the range.
23
Fig. 3.1
Screws
3-Wire Flat Power Cord Installation
(See Figures 3.1 and 3.2)
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 4 fixing Screws (Figure 3.1).
2. Insert the Flat Power Cord through the Bracket; then tighten
the Flat Power Cord by using the Strain Relief. Allow enough
slack to easily attach the cord terminals to the Terminal
Block (Figure 3.2).
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
4. Plug the terminal holes of Flat Power Cord. The Neutral or
Ground Wire of the Flat Power Cord must be connected to
the neutral terminal located in the center of Terminal Block.
The Power Wires must be connected to the outside terminals
(Figure 3.2).
Terminal Block
Access Plate
5. Plug washers and tighten nuts securely.
Fig. 3.2
Terminal Block
Ground strap
Neutral Wire
Power Wires
Bracket
Flat
Power Cord
Strain Relief
24
6. Assemble the Terminal Block Access Plate (Figure 3.1).
3-Wire Power Cord Installation
Fig. 3.3
(See Figures 3.1, 3.3, 3.4 and 3.5)
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 4 fixing Screws (Figure 3.1).
Bracket
Fixing Screws
2. Remove the Bracket and Strain Relief group by unscrewing
the Bracket Fixing Screws (Figure 3.3).
3. Mount the Power Cord Bracket (supplied with the range in
a separate kit - make sure you are using the correct Power
Cord Bracket as indicated in Figure 3.4) inside the Opening
For Electrical Connection by screwing the 2 Fixing Screws
(as indicated in Figure 3.4).
4. Insert the Power Cord through the Power Cord Bracket;
then tighten the Power Cord by using the Power Cord Strain
Relief Bracket (fixed by 2 screws)(see Figure 3.5). The
Power Cord Strain Relief Bracket is supplied with the range
in a separate kit. Allow enough slack to easily attach the cord
terminals to the Terminal Block.
Bracket
Strain Relief
A: D=1" 9/64 (29 mm)
5. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
6. Plug the terminal holes of Power Cord. The Neutral or
Ground Wire of the Power Cord must be connected to the
neutral terminal located in the center of Terminal Block. The
Power Wires must be connected to the outside terminals.
Fig. 3.4
B: D=7/8" (22.5 mm)
Opening For
Electrical
Connection
7. Plug washers and tighten nuts securely.
Fixing Screws
8. Assemble the Terminal Block Access Plate (Figure 3.1).
Power Cord
Bracket
4-Wire Power Cord Installation
(See Figures 3.1, 3.3, 3.4 and 3.6)
Fig. 3.5
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 4 fixing Screws (Figure 3.1).
Terminal Block
Ground strap
2. Remove the Bracket and Strain Relief group by unscrewing
the Bracket Fixing Screws (Figure 3.3).
3. Mount the Power Cord Bracket (supplied with the range in
a separate kit - make sure you are using the correct Power
Cord Bracket as indicated in Figure 3.4) inside the Opening
For Electrical Connection by screwing the 2 Fixing Screws
(as indicated in Figure 3.4).
4. Insert the Power Cord through the Power Cord Bracket;
then tighten the Power Cord by using the Power Cord Strain
Relief Bracket (fixed by 2 screws) (see Figure 3.6). The
Power Cord Strain Relief Bracket is supplied with the range
in a separate kit. Allow enough slack to easily attach the cord
terminals to the Terminal Block.
Neutral Wire
Power Wires
Power Cord
Strain Relief Bracket
Screws
Power Cord
Bracket
Power Cord
5. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
Fig. 3.6
6. Remove the Ground Strap from the frame of range and terminal by removing its screw and cutting it as shown in Figure
3.6.
7. Plug the terminal holes of Power Cord. The Neutral Wire of
the Power Cord must be connected to the neutral terminal
located in the center of Terminal Block; the Power Wires
must be connected to the outside terminals; the Ground Wire
must be attached to the frame of range by using the
(Ground) identified Grounding Screw.
Terminal Block
Cut Ground Strap
Neutral Wire
Power Wires
8. Plug washers and tighten nuts securely.
Power Cord
Strain Relief Bracket
9. Assemble the Terminal Block Access Plate (Figure 3.1).
Screws
Grounding
Screw
Grounding Wire
Power Cord
Power Cord
Bracket
25
3-Wire Conduit Installation
Fig. 3.7
(See Figures 3.1, 3.7, 3.8 and 3.9)
Bracket
Fixing Screws
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 4 fixing Screws (Figure 3.1).
2. Remove the Bracket and Strain Relief group by unscrewing
the Bracket Fixing Screws (Figure 3.7).
3. Mount the Conduit Bracket (supplied with the range in a separate kit - make sure you are using the correct Conduit
Bracket as indicated in Figure 3.8) inside the Opening For
Electrical Connection by screwing the 2 Fixing Screws (as
indicated in Figure 3.8).
Bracket
4. Feed 1/2” (1.3 cm) trade size Conduit through the hole in the
Conduit Bracket and secure to the Conduit Bracket with a
Conduit Clamp (Figure 3.9).
Strain Relief
Fig. 3.8
5. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
A: D=1" 9/64 (29 mm)
B: D=7/8" (22.5 mm)
6. Plug the terminal holes of conductors. The Neutral or Ground
Wire of the Power Cord must be connected to the neutral
terminal located in the center of Terminal Block. The Power
Wires must be connected to the outside terminals.
7. Plug washers and tighten nuts securely.
Opening For
Electrical
Connection
8. Assemble the Terminal Block Access Plate (Figure 3.1).
Fixing Screws
Conduit
Bracket
4-Wire Conduit Installation
Fig. 3.9
(See Figures 3.1, 3.7, 3.8 and 3.10)
Terminal Block
Ground strap
2. Remove the Bracket and Strain Relief group by unscrewing
the Bracket Fixing Screws (Figure 3.7).
Neutral Wire
3. Mount the Conduit Bracket (supplied with the range in a separate kit - make sure you are using the correct Conduit
Bracket as indicated in Figure 3.8) inside the Opening For
Electrical Connection by screwing the 2 Fixing Screws (as
indicated in Figure 3.8).
Power Wires
Conduit Clamp
Conduit
Bracket
Conduit
Terminal Block
Cut Ground strap
Neutral Wire
Grounding
Screw
Conduit Clamp
Grounding Wire
26
Conduit
4. Feed 1/2” (1.3 cm) trade size Conduit through the hole in the
Conduit Bracket and secure to the Conduit Bracket with a
Conduit Clamp (Figure 3.10).
5. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
Fig. 3.10
Power Wires
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 4 fixing Screws (Figure 3.1).
Conduit
Bracket
6. Remove the Ground Strap from the frame of range and terminal by removing its screw and cutting it as shown in Figure
3.10.
7. Plug the terminal holes of conductors. The Neutral Wire of
the Power Cord must be connected to the neutral terminal
located in the center of Terminal Block; the Power Wires
must be connected to the outside terminals; the Ground Wire
must be attached to the frame of range by using the
(Ground) identified Grounding Screw.
8. Plug washers and tighten nuts securely.
9. Assemble the Terminal Block Access Plate (Figure 3.1).
L2
N
EARTH
ST4
ENCODER
2
EL 1000
SIEBE
ST2 +/- ∞C
1
EL1000
4
ETA
ETA
4
OVEN DOOR LATCH
LOCK/UNLOCK
RELAY 3
COOLING
FAN
ST1 PROBE
3
3 ETA
5
2
ETA
AUX ETA
AUX ETA
EL 1000
ST3
Door opened/closed
control device
AIR
SWITCH
1
2
B
E61
RELAY
A
2a
2
1a
1
L1 - L2 = 240V
L1 - N = 120V
L2 - N = 120V
DOOR SAFETY
PILOT LAMP
34 ETA
33 ETA
V
7a
7
OVEN FAN
7
6
G
8a
8
SPIT MOTOR
EL 1000
RELAY 2
THERMOSTAT
PILOT LAMP
CIRCULAR ELEMENT
11a
11
GRILL ELEMENT
EL 1000
RELAY 1
7
4
12a
12
B
B
BOTTOM ELEMENT INT.
TOP ELEMENT
15a
15
E61
THERMOSTAT
16
16a
9a
9
LF
OVEN LAMP
LINE
PILOT LAMP
Safety
Thermal overload
13a
13
5a
5
Safety
Thermostat
RELAY SWITCH
9
6
120
14a
14
A
3a
2
1
BOTTOM ELEMENT EXT.
3
Ignition switces
group
Ignition
coil
Griddle
relay
A2
RELAY
A1
S2
S1
4
P2
PILOT
Energy Regulator
LINE
PILOT LAMP
B
E61
RELAY
2
P1
6a
A
6
6a
9
3
S2
S1
4
P2
PILOT
Energy Regulator
LINE
PILOT LAMP
RELAY SWITCH
E61
2
P1
ST4
ENCODER
2
EL 1000
SIEBE
ST2 +/- ∞C
1
EL1000
4
ETA
ETA
4
OVEN DOOR LATCH
LOCK/UNLOCK
RELAY 3
COOLING
FAN
ST1 PROBE
3
3 ETA
5
2
ETA
AUX ETA
AUX ETA
EL 1000
ST3
Door opened/closed
control device
DOOR SAFETY
PILOT LAMP
34 ETA
33 ETA
Oven door
latch switch
B
AIR
SWITCH
1
2
E61
RELAY
A
2a
2
1a
1
V
7a
7
OVEN FAN
7
6
RELAY 2
G
8a
8
SPIT MOTOR
EL 1000
THERMOSTAT
PILOT LAMP
CIRCULAR ELEMENT
11a
11
GRILL ELEMENT
EL 1000
RELAY 1
7
4
12a
12
B
B
TOP ELEMENT
Safety
15a
15
E61
Safety
Thermal overload
13a
13
5a
5
2 Thermostat
1
RELAY SWITCH
THERMOSTAT
9
6
120
14a
14
A
3a
3
BOTTOM ELEMENT INT.
6
LEFT VARMING DRAWER
Oven door
latch switch
BOTTOM ELEMENT EXT.
L1
RIGHT VARMING DRAWER
9a
9
LF
OVEN LAMP
0422255
LINE
PILOT LAMP
16
16a
WIRING DIAGRAM
27
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in
the present booklet.
The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture
or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and
safety characteristics of the appliances.
Cod. 1102725 - ß3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement