Show literature - Carlisle Fluid Technology

Show literature - Carlisle Fluid Technology
EN
SB-E-2-856 ISS.03
Technical Bulletin
GTIPRO LITE G HVLP and High Efficiency Gravity
Spray Gun (For Industry)
Table of Contents
Topic
Page
EC Declaration of Conformity
3
Part Numbers
3
Operational Description
3
Kit contents
4
Construction Features
4
Materials of Construction
4
Specifications & Technical Data
4
Safety Precautions
5
Parts List
6
Exploded parts View
7
Installation, Operation, Preventive Maintenance & Cleaning
8
Parts Replacement/Maintenance
9
A. Servicing Air Valve
9
B. Needle Packing, Fluid Insert, Spreader Valve Assembly
11
C. Spray Head Seal Replacement
12
D. Chart 1 – Air Caps, Chart 2 – Fluid Nozzles &
Fluid Needles
13
Troubleshooting Possible Problems in Operation
14
Accessories
16
Warranty
16
2
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
EC Declaration of Conformity
We, Finishing Brands UK Limited, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the
manufacturer of the Spray gun model GTIPRO LITE G, declare, under our sole responsibility,
that the equipment to which this document relates is in conformity with the following standards
or other normative documents:
BS EN ISO 12100: 2010, BS EN 1953:2013; and thereby conform to the protection
requirements of Council Directive 2006/42/EC relating to Machinery Safety Directive, and;
EN 13463-1:2009, council Directive 94/9/EC relating to Equipment and Protective
Systems intended for use in Potentially Explosive Atmospheres protection level II 2 G X.
This product also complies with the requirements of the EPA guidelines, PG6/34. Transfer
efficiency certificates are available on request.
D. Smith, Director of Sales (EMEA)
5th May 2016
Finishing Brands UK Limited reserves the right to modify equipment specification without prior notice.
Part Numbers
The ordering code for the GTIPRO LITE G Spray gun is;
E.g. PROLT-GTE10-12 where;
G
=
TE10 =
12
=
Gravity Gun
TE10 Aircap
1.2 Nozzle
See charts 1 & 2 p13 for available Aircap/Nozzle sizes
Operational Description
This GTIPRO LITE G Spray Gun is a professional quality gun designed with both high volume,
low pressure (HVLP) technology or High Efficiency EPA compliant technology. HVLP
Technology reduces overspray and limits air cap pressure to 0.7 bar (10 psi). High Efficiency
complies with EPA by obtaining transfer efficiency above 65%.
IMPORTANT: These Sprayguns are suitable for use with both waterbased and solvent based
coating materials. These guns are not designed for use with highly corrosive and/or abrasive
materials and if used with such materials it must be expected that the need for cleaning and/or
replacement of parts will be increased. If there is any doubt regarding the suitability of a specific
material, contact your DeVilbiss Distributor or DeVilbiss direct.
NOTE: This gun is not to be used with halogenated hydrocarbon solvents or cleaning agents
such as 1,1,1,-Trichloroethane or methylene chloride. These solvents can react with the
aluminium components used in this gun and cup. The reaction can become violent and lead to
an equipment explosion.
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
3
Kit contents (all models)
1
1
1
1
GTIPRO LITE Gravity Feed Spraygun
GFC Gravity feed cup
Cup Filter
Set of 4 coloured identification rings
1
1
1
1
Spanner (10mm and 14mm A/F)
Torx/Flat blade screwdriver
Cleaning Brush
Service bulletin
Construction Features
Fan Air Adjustment (stepless regulation for fan
to round spray)
Fluid Adjustment (stepless regulation of fluid
volume)
Interchangeable Colour ID System (4 coloured
rings supplied)
Anodised, forged aluminium gun body
(ergonomic, good looking & durable, easy to
clean)
1
Air Cap (nickel plated brass for long durability)
10
2
Air Cap Retaining Ring (allows easy rotation of air
cap)
11
3
Fluid Nozzle (ideal for most paint systems)
12
4
Fluid Needle (grooved stem for easy removal)
13
5
Fluid Inlet (3/8 BSP thread – accepts DeVilbiss and
most other cup systems)
14
500cc Acetal Cup (easy clean, anti-static)
Air Inlet (universal thread, accepts G 1/4 & 1/4 NPS)
Self Adjusting Needle Packing (for trouble free
operation)
15
8
Trigger (ergonomic for comfort)
17
Cup Lid with Drip Free Vent (avoid drips)
Air Valve (design offers low pull force & low
pressure drop)
Gun acceptable for waterborne and solvent
borne applications
9
Trigger Stud & Screw (easy replacement design)
6
7
16
Materials of Construction
Gun Body
Anodised aluminium
Air Cap,
Nickle Plated Brass
Fluid Nozzle, Fluid Needle, Fluid Inlet, Trigger Stud
Stainless steel
Adjusting Knobs, Air Cap Retaining Ring,
Anodized aluminium
Springs, Clips, Screws
Stainless steel
Seals, Gaskets
Solvent resistant
Trigger
Chrome plated steel
Air Inlet, Body Bushing, Spreader Valve Body, Air Valve Nut.
Chrome plated brass
Air Valve Assembly
Aluminium
Specifications & Technical Data
Air Supply Connection
Maximum Static Air Inlet Pressure
Gun Air Inlet Pressure for HVLP
®
and High Efficiency
both with gun triggered.
Fluid Supply Connection
Service Temperature
Universal 1/4" BSP and 1/4" NPS male
P1 = 12 bar (175 psi)
Gun Weight (gun only)
(with cup)
446g
629g
0.69 bar (10 psi)
2.0 bar (29 psi)
3/8" BSP
0 to 40°C (32 to 104°F)
4
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
SAFETY WARNINGS
Fire and explosion
Solvents and coating materials can be highly flammable or combustible when sprayed.
ALWAYS refer to the coating material supplier’s instructions and COSHH sheets before
using this equipment.
Users must comply with all local and national codes of practice and insurance company
requirements governing ventilation, fire precautions, operation and house-keeping of
working areas.
This equipment, as supplied, is NOT suitable for use with Halogenated Hydrocarbons.
Static electricity can be generated by fluid and/or air passing through hoses, by the
spraying process and by cleaning non-conductive parts with cloths. To prevent ignition
sources from static discharges, earth continuity must be maintained to the spray gun
and other metallic equipment used. It is essential to use conductive air and/or fluid
hoses.
Personal Protective Equipment
Toxic vapours – When sprayed, certain materials may be poisonous, create irritation or
be otherwise harmful to health. Always read all labels, safety data sheets and follow any
recommendations for the material before spraying. If in doubt, contact your material
supplier.
The use of respiratory protective equipment is recommended at all times. The type of
equipment must be compatible with the material being sprayed.
Always wear eye protection when spraying or cleaning the spray gun.
Gloves must be worn when spraying or cleaning the equipment.
Training – Personnel should be given adequate training in the safe use of spraying equipment.
Misuse
Never aim a spray gun at any part of the body.
Never exceed the maximum recommended safe working pressure for the equipment.
The fitting of non-recommended or non-original spares may create hazards.
Before cleaning or maintenance, all pressure must be isolated and relieved from the equipment.
The product should be cleaned using a gun-washing machine, and should be removed and dried
immediately after cleaning is completed. Prolonged exposure to cleaning solutions can cause
damage to the product.
Noise Levels
The A-weighted sound level of spray guns may exceed 85 dB (A) depending on the setup being used. Details of actual noise levels are available on request. It is
recommended that ear protection is worn at all times when spraying.
Operating
Spray equipment using high pressures may be subject to recoil forces. Under certain
circumstances, such forces could result in repetitive strain injury to the operator.
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
5
PARTS LIST
REF.
NO.
DESCRIPTION
PART NO.
QTY
REF.
NO.
DESCRIPTION
PART NO.
QTY
1
Air Cap Retaining Ring
-
1
30
Gunbody
-
1
2
Slip Ring
-
1
31
Air Inlet
-
1
3
Air Cap
-
1
32
Colour ID Ring Kit (4
Colours)
SN-26-K4
1
4
Air Cap Retaining Clip
1
33
Air Inlet Kit
SN-9-K
1
5
Retaining Ring Seal
-
1
34
Needle Packing
-
1
6
Aircap & Ring
See chart 1
p13
1
35
Packing Spring
-
1
7
Air Cap Retaining Ring &
Seals
1
36
Packing Nut
-
1
8
Fluid Nozzle Kit
See chart 2
p13
1
*37
Packing, Spring and
Packing Nut Kit
9
Spray Head
-
1
*38
Trigger Screw
-
1
JGA-156-K5
PRO-420-K
SN-404-K
1
*10
Spray head Seal
SN-18-1-K2
1
39
Trigger
-
1
11
Spray head kit
SN-69-K
1
*40
Trigger Stud
-
1
*12
Circlip
-
1
41
Trigger Stud & Screw
Kit
SP-617-CR-K
1
13
Valve Body
-
1
42
Airflow Valve
PRO-407-K
1
*14
O Ring
-
1
43
Circlip - Kit of 5
25746-007-K5
1
*15
Spreader Valve Pin
2
44
Valve Head
-
1
1
45
Washer
-
1
1
46
Valve Body
-
1
-
1
16
17
Spreader Valve
Adjusting Knob
Spreader Valve
Assembly
PRO-406-K
18
Front Valve Seal
-
1
47
Valve Adjusting Knob
19
Valve Seat
-
1
48
Filter
20
Spindle
-
1
49
Gravity Cup
21
Air Valve Spring
-
1
50
Gravity Cup Lid
GFC-402
1
22
Rear Valve Seal
-
1
51
Drip Check Lid (kit of 5)
GFC-2-K5
1
23
Air Valve Kit
PRO-471
1
52
Gravity Cup Kit
GFC-501
1
24
Fluid Needle
PRO-301-K
1
+53
Air Valve Service Tool
25
Needle Spring
-
1
54
Tool kit
26
Spring Pad
-
1
27
Housing
SN-66-K
1
28
Fluid Adjusting Knob
SN-67-C-K
1
*29
Needle Spring Kit
PRO-472-K3
1
KGP-5-K5
-
1
1
-
1
SN-406
1
SERVICE PARTS
Spray Gun repair kit (includes
items marked *)
Seal and Pin Kit, kit of 5
(items 12, 14 and 15)
PRO-470
GTI-428-K5
+ Not included in the Gun Kit, only with ref 23
6
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
7
INSTALLATION
9.
For maximum transfer efficiency, do not use more
pressure than is necessary to atomise the material
being applied. NOTE: when using the HVLP do not
exceed 1.75 bar inlet pressure.
10.
1.
11.
2.
3.
Connect the gun to a clean, moisture and oil free
air supply using a conductive hose, of at least 8
mm I.D.
NOTE
Depending on hose length, larger I.D. hose may
be required. Install an air gauge at the gun
handle. When gun is triggered on, adjust
regulated pressure to 2.0 bar for High Efficiency
Aircaps and 1.75 bar for HVLP. Do not use more
pressure than is necessary to atomise the
material being applied. Excess pressure will
create additional overspray and reduce transfer
efficiency.
NOTE
If quick connect couplings are required, use only
high flow quick connects approved for HVLP
use. Other types will not flow enough air for
correct gun operation.
NOTE
If an air adjusting valve is used at the gun inlet,
use DGIPRO-502-BAR Digital Gauge. Some
competitive adjusting valves have significant
pressure drop that can adversely affect spray
performance. The DGIPRO Digital Gauge has
minimal pressure drop, which is important for
HVLP spraying.
12.
13.
14.
PREVENTIVE MAINTENANCE &
CLEANING
To clean air cap and fluid nozzle, brush exterior with
a stiff bristle brush. If necessary to clean cap holes,
use a broom straw or toothpick if possible. If a wire or
hard instrument is used, extreme care must be used
to prevent scratching or burring of the holes which
will cause a distorted spray pattern.
To clean fluid passages, remove excess material
from cup, then flush with gun wash solution. Wipe the
gun exterior with a dampened cloth. Never
completely immerse in any solvent or cleaning
solutions as this is detrimental to the lubricants and
life of the spray gun.
NOTE
When replacing the fluid nozzle or fluid needle,
replace both at the same time. Using worn parts can
cause fluid leakage. See page 13, Chart 2. Also,
replace the needle packing at this time. Torque the
fluid nozzle to 18–20 Nm. Do not over tighten.
Insert the filter (48) into the
inlet of the Gravity Cup.
Make sure the body of the
filter is pushed fully so the
body of the filter does not
protrude from the cup insert.
CAUTION
To prevent damage to fluid nozzle (8) or fluid
needle (24), be sure to either 1) pull the trigger
and hold while tightening or loosening the fluid
nozzle, or 2) remove fluid adjusting knob (28) to
relieve spring pressure against needle collar.
Attach the gravity feed cup
to the material inlet.
NOTE
Before using the gun, flush it with solvent to
ensure that the fluid passages are clean.
CAUTION
OPERATION
1.
2.
3.
4.
5.
6.
7.
8.
If finish is too wet, reduce fluid flow by turning
fluid adjusting knob (28) clockwise. If atomisation
is too coarse, increase inlet air pressure. If too
fine, reduce inlet pressure.
The pattern size can be reduced by turning
spreader valve knob (16) clockwise.
Hold gun perpendicular to surface being
sprayed. Arcing or tilting may result in uneven
coating.
The recommended spray distance is 150-200
mm.
Spray edges first. Overlap each stroke a
minimum of 75%. Move gun at a constant speed.
Always turn off air supply and relieve pressure
when gun is not in use.
IMPORTANT– the Gravity cup is made from
special anti-static materials, but it is still
important to avoid generating static charges. The
Cup must not be cleaned or rubbed with a dry
cloth or paper. It is possible to generate a static
charge by rubbing which, if discharged to an
earthed object could create an incendive spark
and cause solvent vapours to ignite. Only use a
dampened cloth or antistatic wipes if manual
cleaning is required within a hazardous area.
Mix coating material to manufacturer’s
instructions and strain material.
Fill the cup to no more than 20 mm from the top
of the cup. DO NOT OVERFILL.
Attach Cup Lid.
Turn fluid adjusting knob (28) clockwise to
prevent fluid needle movement.
Turn spreader valve adjusting knob (16) counter
clockwise to fully open.
Adjust inlet air pressure if required.
Turn fluid adjusting knob (28) counter clockwise
5 turns for full needle travel.
Test spray. If the finish is too dry, reduce airflow
by reducing air inlet pressure.
8
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
Parts
Replacement/Maintenance
AIR VALVE INSTRUCTIONS
Servicing Air Valve
Reasons to service air valve:
A) Air valve not functioning correctly
(may need cleaning).
B) Routine maintenance.
C) Air leaks.
1. Remove trigger screw (38) with Torx tool
(55) or Torx T20 key. (See fig 2).
2. Remove trigger stud (40) and remove
trigger (39) (See fig 3).
3. Remove fluid adjusting knob (28) and
spring (29). (See fig 4).
4. Remove fluid needle (24) (See fig 5).
5. Using a 6mm hex key, remove Valve
housing (27). (See Figs 6 and 7).
6. Remove spring (21) and valve spindle
(20). (See Fig 8).
7. Using service tool (53), engage groove
behind the valve seat (19) (See Fig 9).
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
9
8. Withdraw the valve seat (19) from the gun
body. (See fig 10).
9. Push out the front airvalve seal (18) with a
finger. (See fig 11).
10. Turn the Gun upside down and let the seal
fall out. (See fig 12).
11. Fit New front seal (18) to service tool (53).
Fit into gunbody and press firmly to ensure
Seal is engaged. (See fig 13).
12. Fit a new valve seat (19) to service tool
(53). Groove must face outwards. (See fig
14).
13. Fit valve seat (19) to gunbody. (See fig 15)
14. Remove rear airvalve seal (22) from housing
(27) with a hooked instrument. (See fig 16).
15. Fit new seal (22) to service tool (53). Groove
must face outwards. Press seal (22) to
housing (27). (See fig 17)
16. Reassemble remaining parts in reverse
order - valve (20), spring (21), housing (27)
and tighten with 6mm hex key, needle (24)
spring (29) and knob (28). Replace trigger
(39), fitting trigger stud (40), and screw in the
trigger screw (38) with Key (55) or Torx Key
T20.
17. Trigger gun fully and screw in fluid adjusting
knob (28) until it stops. Back it off 1/2 turn
and gun will have full needle travel.
18. Trigger gun several times to verify correct
operation.
10
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
Parts
Replacement/Maintenance
NEEDLE PACKING
REPLACEMENT INSTRUCTIONS
1. Remove trigger and needle following steps
1 to 6 on P9, servicing airvalve.
2. Loosen and remove packing nut using Key
(57) or a straight blade screwdriver. (See
figs 18 & 19)
3. Discard old packing (34) and packing spring
(35) if replacing.
Clean packing if reusing. Also clean packing
spring and nut (36). (See fig 20).
4. Re-assemble the packing, assemble into
gunbody by hand and then tighten. (See fig
21)
5. Complete re-assembly following 16 to 24 on
P10.
SPREADER VALVE ASSEMBLY
REPLACEMENT/MAINTENANCE
The spreader valve assembly can be replaced if
damaged. Remove using 14 mm Spanner (56)
(See figs 22 & 23). The internal seal can be
replaced and is included in the Gun Rebuild Kit
(See fig 24).
FLUID SUPPLY INSERT
The fluid insert and seal are NOT replaceable.
(See fig 25).
Do not remove these parts.
No maintenance is required for these parts
other than regular cleaning of the internal bore.
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
11
Parts Replacement/
Maintenance
SPRAY HEAD SEAL
REPLACEMENT
1. Remove air cap and retaining ring (6).
(See fig 26).
2. Remove fluid adjusting knob (28), spring
(25), and spring pad (26). (See fig 27).
3. Remove fluid needle (24) from gun body.
(See fig 28).
4. Remove fluid nozzle using 10mm
Spanner (56). (See fig 29)
5. Remove spray head (9) and Seal (10)
(See fig 30).
6. Remove seal (10) from spray head. (See
fig 31).
7. Clean front of gun if required, using a soft
brush, as well as the fluid nozzle, air cap,
and retaining ring.
8. Place a new seal (10) into the front of the
gun, making sure the flat of the seal is
aligned to the flat in the gun. (See fig 32).
9. Fit the spray head (9), making sure the
pin is engaged into the hole in the
gunbody. (See fig 33).
10. Fit fluid nozzle (8), air cap and retaining
Ring (6). Torque the fluid nozzle to 18–20
Nm (160–180 lbs.in). Do not over torque
the fluid nozzle. (See figs 34, and 35)
11. Reassemble remaining parts in reverse
order - fluid needle ( 24), Needle spring
and pad (29), and fluid adjusting knob
(28).
12. Trigger gun fully and screw in fluid
adjusting knob (28) until it stops. Back it
off 1/2 turn and gun will have full needle
travel.
13. Trigger gun several times to verify correct
operation.
12
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
Parts Replacement/Maintenance
Chart 1 – Air Caps
PART No. FOR
AIR CAP
TECHNOLOGY
MARKING ON
AIR CAP
RECOMMENDED
INLET
PRESSURE
(bar)
AIR FLOW
(L/min) @ 2
bar
PRO-102-HV30-K
HVLP
HV30
1.75
465
PRO-102-TE10-K
HIGH
EFFICIENCY
TE10
2.0
275
PRO-102-TE20-K
HIGH
EFFICIENCY
TE20
2.0
350
NOTE: When removing air cap from retaining ring, don’t remove the Slip Ring (2) or Retaining Ring Seal (5) from
the Retaining Ring. Damage to the parts may occur. Slip ring and Retaining Ring seal are not available as
replacements. Simply wipe parts clean and reassemble with new or clean air cap.
Chart 2 – Fluid Nozzle Range & Fluid Needle
PART No. FOR FLUID NOZZLE
PART No. NEEDLE
PRO-200-12-K
PRO-200-13-K
PRO-301-K
PRO-200-14-K
PRO-200-16-K
PRO-200-18-K
PRO-303-K
PRO-200-20-K
NOTE: When replacing the fluid nozzle or fluid needle, replace both at the same time. Torque to 18–20 Nm (160–
180 lbs.in). Do not over tighten the fluid nozzle. Use SN-28 (56) 10mm Spanner supplied with the gun and check
with a torque wrench.
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
13
Troubleshooting Possible Problems in Operation
CONDITION
CAUSE
CORRECTION
Heavy top
or
bottom
pattern
Horn holes plugged.
Clean. Ream with non-metallic
point.
Obstruction on top or bottom of fluid
nozzle.
Clean.
Cap and/or nozzle seat dirty.
Clean.
Left or right side horn holes plugged.
Clean. Ream with non-metallic
point.
Dirt on left or right side of fluid
nozzle.
Clean.
Heavy right
or left side
pattern
Remedies for the top-heavy, bottom-heavy, right-heavy, and left-heavy patterns:
1. Determine if the obstruction is on the air cap or the fluid nozzle. Do this by making a test spray pattern. Then,
rotate the cap one-half turn and spray another pattern. If the defect is inverted, obstruction is on the air cap.
Clean the air cap as previously instructed. Also check for dried paint just inside the cap centre hole opening;
remove by washing with solvent.
2. If the defect is not inverted, it is on the fluid nozzle. Clean nozzle. If problem persists, renew nozzle.
Heavy
centre
pattern
Split spray
pattern
Jerky or fluttering spray
Paint bubbles in cup
Fluid leaking or dripping from cup
lid
Spreader adjustment valve set too
low.
Turn out counter clockwise to
achieve correct pattern.
Atomising pressure too low.
Increase pressure.
Material too thick.
Thin to correct consistency.
Air pressure too high.
Reduce at regulator or gun handle.
Fluid adjusting knob turned in too
far.
Turn out counter clockwise to
achieve correct pattern.
Spreader adjusting valve set too
high.
Turn in clockwise to achieve
correct pattern.
Loose or damaged fluid nozzle/seat
Tighten or replace
Loose or broken cup fluid nipple
Tighten or replace cup
Material level too low
Refill
Container tipped too far
Hold more upright
Obstruction in fluid passage
Back flush with solvent
Loose fluid needle packing nut
Tighten
Damaged fluid needle packing
Replace
Fluid nozzle not tight.
Cup lid loose.
Tighten to 18–20 Nm (160–180
lbs.in).
Push in or replace.
Dirty cup or lid.
Clean.
Cracked cup or lid.
Replace cup and lid.
14
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
Troubleshooting Possible Problems in Operation (cont)
Inadequate material flow
Starved spray pattern
Excessive overspray
Blocked vent in Cup lid
Increase air pressure and
rebalance gun.
Air pressure to high.
Reduce air pressure.
Gun too far from work surface.
Adjust to correct distance.
Reduce air pressure.
Gun too far from work surface.
Fluid leaking or dripping
from front of gun
Fluid dripping or leaking
from bottom of cup
Runs and sags
Adjust to correct distance.
Slow down.
Gun motion too fast.
Fluid leaking from
packing nut
Clean lid and unblock vent
Low atomisation air pressure
Air pressure too high.
Dry spray
Wind fluid adjusting knob out or
change to larger fluid nozzle size
Fluid flow too low.
Wind out needle adjusting screw or
use larger nozzle size.
Packing worn.
Replace.
Fluid nozzle or fluid needle worn or
damaged.
Replace fluid nozzle and fluid
needle.
Foreign matter in fluid nozzle.
Clean.
Fluid needle dirty or stuck in needle
packing
Clean
Wrong size fluid needle or fluid
nozzle.
Replace fluid nozzle and fluid
needle.
Cup loose on gun.
Tighten
Cup fluid inlet seat dirty.
Clean.
Too much material flow.
Turn fluid adjusting knob clockwise
or switch to smaller fluid nozzle
and fluid needle size.
Material too thin.
Mix correctly or apply light coats.
Gun tilted on an angle, or gun
motion too slow.
Hold gun at right angle to work and
adapt to correct gun technique.
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
15
ACCESSORIES
DGi PRO Digital
Pressure Gauge
DGIPRO-502-BAR
Spanner
Torx driver
SN-406
Cleaning Brush
Cleaning Brush
4900-5-1-K3
Torx driver
SPN-8-K2
Gun Stand
GFV-50-F
600 cc Mixing
Cups pack of 50
MC-1-K50
10m x 8mm bore
rubber air hose
with ¼ fittings
H-6065-B (BSP)
H-6065-N (NPS)
Pack of four QD
fittings
MPV-463
MPV Swivel
MPV-60-K3
WARRANTY
This product is covered by Finishing Brands UK Limited one year warranty.
Carlisle Fluid Technologies,
Dba, Finishing Brands UK Limited,
Ringwood Road,
Bournemouth,
BH11 9LH,
UK.
Tel.No: 01202 571111
Fax No: 01202 581940
Website address http:// www.finishingbrands.eu
Registered office:
Finishing Brands UK Limited,
400, Capability Green,
Luton,
Bedfordshire,
LU1 3AE,
UK.
Registered in England: No. 07656273
Vat No: GB 113 5531 50
16
© 2016 Carlisle Fluid Technologies, dba Finishing Brands UK Ltd
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising