i series analog - Teledex Europe

i series analog - Teledex Europe
I SERIES ANALOG
USER GUIDE
For A Series, AC Series, and AT (Trimline) Series
Important Safety Instructions
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock, and injury
to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug the product from the wall outlet
before cleaning. Do not use liquid cleaner
or aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this product near water—for
example, near a bathtub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool.
5. Do not place this product on an unstable
cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and
the back or bottom are provided for
ventilation, to protect it from overheating.
These openings must not be blocked or
covered. The openings should never be
blocked by placing the product on the bed,
sofa, rug, or any other similar surface.
This product should never be place near
or over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
7. Never push objects of any kind into this
product through cabinet slots as they may
touch dangerous voltage points or short
out parts that could result in a risk of fire
or electric shock. Never spill liquid of any
kind on the product.
8. To reduce the risk of electric shock do
not disassemble this product. Take it to a
qualified service facility if service or repair
work is required. Opening or removing
covers may expose you to dangerous
2
voltages or other risks. Incorrect
reassembly can cause electric shock when
the appliance is subsequently used.
9. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
– When the power supply cord or plug is
damaged or frayed.
– If liquid has been spilled into the
product.
– If the product has been exposed to rain
or water.
– If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions, as
improper adjustment of other controls
may result in damage and may require
extensive work by a qualified technician
to restore the product to normal
operation.
– If the product has been dropped or the
cabinet has been damaged.
– If the product exhibits a distinct change
in performance.
10. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
11. Do not use the telephone to report a gas
leak in the vicinity of the leak.
PLEASE SAVE THESE INSTRUCTIONS.
FCC Interference Information
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna
for the radio or television that is receiving the
interference).
– Reorient or relocate and increase the
separation between the telecommunications
equipment and receiving antenna.
– Connect the telecommunications equipment
into an outlet on a circuit different from that to
which the receiving antenna is connected.
FCC RF Radiation Exposure
Statement
The installation of the base unit should allow
at least 20 centimeters between the base
and persons to be in compliance with FCC RF
exposure guidelines. For body-worn operation,
the portable part (handset) has been tested and
meets FCC RF exposure guidelines.
This device must not be co-located or operating
in conjunction with any other antenna or
transmitter. The changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
Industry of Canada Requirements
Note: This equipment meets the applicable
Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the
registration number. The abbreviation, IC, before
the registration number signifies that registration
was performed based on a Declaration of
Conformity indicating that Industry Canada
technical specifications were met. It does not imply
that Industry Canada approved the equipment.
Before installing this equipment, users should
ensure that it is permissible to be connected to
the facilities of the local telecommunications
company. The equipment must also be installed
using an acceptable method of connection. The
customer should be aware that compliance with
the above conditions may not prevent degradation
of service in some situations.
Repairs to certified equipment should be
coordinated by a representative designated by the
supplier. Any repairs or alterations made by a user
to this equipment, or equipment malfunctions,
may give the telephone communications company
cause to request the user to disconnect the
equipment.
Users should ensure for their own protection, that
the electrical ground connections of the power
utility, telephone lines, and internal metallic
water pipe system, if present, are connected
together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such
connections themselves, but should contact
the appropriate electric inspection authority, or
electrician, as appropriate.
Notice: The Ringer Equivalence Number (REN)
assigned to each terminal device provides an
indication of the maximum number of terminals
allowed to be connected to a telephone interface.
The termination on an interface may consist
3
of any combination of devices subject only to
the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not
exceed 5.
REN: Z
For warranty and service in Canada, please
contact:
Williams Telecommunications
5610 Kennedy Road
Mississauga, Ontario, L4Z2A9
Canada
Phone: 905-712-4242
Fax: 905-712-1754
Requirements of Part 15—
FCC Rules
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
1. Move the telephone away from the
receiver.
2. Consult the dealer or an experienced
radio/TV technician for help.
Any changes made by the user not approved by
the manufacturer can void the user’s authority to
operate the telephone.
4
Requirements of Part 68—
FCC Rules
This equipment complies with Part 68 of the FCC
Rules and the requirements adopted by ACTA.
On the bottom of this telephone is a label that
contains, among other information, a product
identifier in the format US:AAAEQ##TXXXX. If
requested, this number must be provided to
the telephone company. The USOC Jack for this
equipment is RJ11C.
A plug and jack used to connect this equipment
to the premises wiring and telephone network
must comply with the applicable FCC Part 68
rules and requirements adopted by ACTA. A
compliant telephone cord and modular plug are
provided with this telephone. It is designed to be
connected to a compatible modular jack that is
also compliant. See installation instructions for
details.
The Ringer Equivalence Number (REN) is used
to determine the number of devices that may be
connected to a telephone line. Excessive RENs
on a telephone line may result in the devices
not ringing in response to an incoming call. In
most but not all areas, the sum of RENs should
not exceed five (5.0). To be certain of the number
of devices that may be connected to a line, as
determined by the total RENs, contact the local
telephone company. For products approved after
July 23, 2001, the REN for this product is a part
of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 03
is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this telephone causes harm to the telephone
network, the telephone company will notify you
in advance that temporary discontinuance of
service may be required. But if advance notice is
not practical, the telephone company will notify
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
the customer as soon as possible. Also, you will
be advised of your right to file a complaint with
the FCC if you believe it is necessary.
The telephone company may make changes in its
facilities, equipment, operations, or procedures
that could affect the operation of the equipment.
If this happens, the telephone company will
provide advance notice in order for you to
make the necessary modifications to maintain
uninterrupted service.
If trouble is experienced with this equipment, for
repair or warranty information, please contact
Teledex at (800) 462-9446. If the equipment is
causing harm to the telephone network, the
telephone company may request that you disconnect
the equipment until the problem is resolved.
There are no user-serviceable parts contained in
this equipment.
Technical Specifications
This guide covers product made from 2009
forward with a serial number beginning with XX.
For all other models please refer to the Teledex
website for legacy product documentation.
DIMENSIONS
6.0” (w) x 9.0” (l) x 3.375” (h)
WEIGHT
With handset: 2.0 lbs.
POWER ADAPTER
7.5VDC 300mA Adapter (for cordless HDKIT)
9 VDC 300mA (Pass through adapter for cordless
telephone)
User Guides
Connection to party line service is subject to
state tariffs. Contact the state public utility
commission, public service commission, or
corporation commission for information.
If additional User Guides are needed, please go
to www.teledex.com to download the PDF.
If your home has specially wired alarm equipment
connected to the telephone line, ensure the
installation of this product does not disable your
alarm equipment. If you have questions about
what will disable alarm equipment, consult your
telephone company or a qualified installer.
When problems arise that cannot be resolved
using this or related documents, please go to
www.teledex.com/support for information about
customer support, technical support, warranty,
and product returns.
This telephone is hearing aid compatible.
Statement of Limited Warranty
These telephone devices are intended for
commercial use only, primarily in hotel guestrooms.
They must be used with a PBX (private branch
exchange), and are not intended to be connected
directly to a PSTN line (public switched telephone
network). There are no user-serviceable parts
inside the equipment.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
Service
Teledex product warranty information is available
at www.teledex.com.
5
Table of Contents
I Series A 1-Line Analog Phone Map
...........
7
I Series A 2-Line Analog Phone Map
...........
7
I Series AC 1-Line Analog Phone Map
.........
8
I Series AC 2-Line Analog Phone Map
.........
8
I Series AT Trimline Analog Phone Map
........ 9
I Series A Series (Analog Corded)
............
Unpacking Your Telephone . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caution Information . . . . . . . . . . . . . . . . . . .
Connecting the I Series A Series . . . . . . . . .
Converting from Desk to Wall Mount . . . . . .
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume Control . . . . . . . . . . . . . . . . . . . . . . .
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . .
Using the Speakerphone
(Speakerphone-Equipped Models) . . . . . . . .
Mute (Speakerphone-Equipped
Models Only) . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference (Two-Line Models Only) . . . . . .
Using the Hold Key (Two-Line Models
Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming . . . . . . . . . . . . . . . . . . . . . . . . . .
Guest Service Keys . . . . . . . . . . . . . . . . . . . . . . .
Pause Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care and Maintenance . . . . . . . . . . . . . . . . . . .
10
10
10
10
10
10
11
11
11
11
11
I Series AC Series (Analog Cordless)
.........
Unpacking Your Telephone . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caution Information . . . . . . . . . . . . . . . . . . .
Preparing to Use the AC Series . . . . . . . . . .
....
Handset/Base Registration Procedure
Charging the Battery . . . . . . . . . . . . . . . . . . .
Cleaning the Battery Contacts . . . . . . . . . . .
Battery Safety Instructions . . . . . . . . . . . . . .
Converting From Desk to Wall Mount . . . . .
14
14
14
14
14
14
15
15
15
15
6
11
12
12
12
12
12
12
13
13
13
13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting Speakerphone Volume . . . . . . . . .
Adjusting Handset Receive Volume . . . . . . .
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . .
Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Line 1 and Line 2
(Two-Line Models Only) . . . . . . . . . . . . . . . . .
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Hold Key . . . . . . . . . . . . . . . . . . . .
To Mute the Speakerphone . . . . . . . . . . . . . .
Conference (Two-Line Models Only) . . . . . .
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Dial Keys . . . . . . . . . . . . . . . . . . . . . . . .
Pause Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care and Maintenance . . . . . . . . . . . . . . . . . . .
I Series AT Series (Analog Trimline)
..........
Unpacking Your Telephone . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caution Information . . . . . . . . . . . . . . . . . . .
Connecting the Phone . . . . . . . . . . . . . . . . . .
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Waiting Indicator
(Models AT1101 and AT1201 Only) . . . . . . . .
Backlit Keypad . . . . . . . . . . . . . . . . . . . . . . . .
Analog Data Port . . . . . . . . . . . . . . . . . . . . . .
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . .
Initiating a New Call . . . . . . . . . . . . . . . . . . .
Adjusting the Ring Volume . . . . . . . . . . . . . .
Adjusting the Handset Volume . . . . . . . . . . .
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference (Two-Line Models Only) . . . . . .
Using the Hold Key (Two-Line Models
Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care and Maintenance . . . . . . . . . . . . . . . . . . .
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
16
16
16
16
16
17
17
17
17
17
18
18
18
18
18
19
20
20
20
20
20
20
20
20
20
20
20
20
20
20
21
21
21
21
21
21
21
I Series A 1-Line Analog Phone Map
I Series A 2-Line Analog Phone Map
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
7
I Series AC 1-Line Analog Phone Map
I Series AC 2-Line Analog Phone Map
8
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I Series AT Trimline Analog Phone Map
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
9
I SERIES A SERIES PHONES (ANALOG CORDED)
Unpacking Your Telephone
This package should contain the following:
• Handset
• Line cord
• Phone base unit
• Clear plastic overlay
• Coiled handset cord
• User guide
Installation
CAUTION INFORMATION
• Never install telephone or network wiring
during a lightning storm.
• Never install telephone or Ethernet jacks in
wet locations unless the jack is specifically
designed for wet locations.
• Never touch uninstalled telephone wires or
terminals unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying
telephone and network lines.
CONNECTING THE I SERIES A SERIES
1. Located on the left side of the I Series
phone (as the phone is facing you) is a
modular jack. Insert one end of the coiled
handset cord into this jack (you should hear
the coil cord click when properly inserted).
2. Insert the other end of the coiled handset
cord into the modular jack on the handset.
3. Turn the telephone so the back panel
is facing you. Insert either end of the
line cord into the jack on the back of the
telephone labeled LINE.
4. Insert the other end of the line cord into a
telephone wall outlet jack.
5. Once your telephone is connected, remove
the plastic overlay and place the paper
faceplate over the keys. Replace the plastic
overlay by hooking the tabs on the overlay
into the recessed slots located on both sides.
10
CONVERTING FROM DESK TO WALL
MOUNT
The I Series phone can be converted for wall
mounting applications. The conversion is easiest
when the handset and line cords are not connected.
1. Located on the top of the telephone above
the speaker grill is the wall/desk mount
clip. Remove this clip by firmly pushing
upward (towards the hookswitch).
2. Flip the clip over (top to bottom) so that
the protruding edge is towards the top of
the phone, and reinsert into cutout. This
protruding edge will hold the handset.
3. Turn the telephone over so the bottom is
up, facing you. Place the telephone on a
non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket,
firmly push back and pull up to remove two
of the four retaining tabs.
5. Rotate the mounting bracket 180 degrees
clockwise so that the mounting eyelet on
the bracket is facing in the same direction
as the other mounting eyelet located on
the bottom of the telephone.
6. Insert the top two retaining tabs of the
mounting brackets into the mounting
bracket slots (located near the middle of
the telephone). Then firmly push down to
insert the retaining tabs on the opposite
side of the mounting bracket.
7. Connect a short modular line cord into
the jack on the back of the phone (labeled
LINE). Route the line cord through the
line cord channel. Connect the other end
of line cord to the phone jack on the wall
mounting plate.
8. Turn the telephone over, and slide the
telephone down onto the mounting posts
in downward direction. Both eyelets should
line up with the mounting posts.
9. Complete the wall mounting by installing
the handset and handset cord.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES A SERIES PHONES (ANALOG CORDED)
Operation
3. To end the call, hang up by placing the
handset back in the cradle.
VOLUME CONTROL
ADJUSTING THE HANDSET VOLUME
To the left of the dialpad, locate the volume up/
down arrow keys. While using the handset,
either during an active call, or preparing to dial,
press either the up or down key to raise or lower
handset volume to the desired level.
ADJUSTING THE RING VOLUME
On the rear panel of the telephone, locate
the ringer volume slide swtich. There are two
settings: Low and High. Set the switch to the
desired setting.
ADJUSTING THE SPEAKERPHONE VOLUME
To the left of the dialpad, locate the volume up/
down arrow keys. With the speakerphone active,
press either the up or down key to raise or lower
speaker volume to the desired level.
INDICATORS
SPEAKER, MUTE, AND HOLD KEY
CONNECTING AND STATUS INDICATORS
Speakerphones are equipped with LED indicators
to show the current feature key status.
• Press the Speaker, Mute, or Hold feature key
to use that service—the LED will light red
when that key is IN USE.
CALLING
PLACING A CALL USING THE HANDSET
1. Lift the handset. The LINE LED will
illuminate. (On two-line models, if both
lines are inactive, Line 1 will be activated.
If one of the two lines is active, the inactive
line will be activated.)
2. Listen for dial tone. Dial the desired
number, or press an AUTO DIAL key to
automatically dial a number.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
PLACING A CALL USING THE SPEAKERPHONE
(ONLY MODELS WITH SPEAKERPHONE)
1. With the handset in the cradle, press
either the SPEAKER key or the LINE key
(on two-line models, select either inactive
LINE key). The telephone will go offhook
on the selected line with speakerphone
active.
2. Listen for dial tone, and dial the desired
number, or press an AUTO DIAL key to
automatically dial a number.
3. To end the call, press the SPEAKER key.
RECEIVING A CALL
TO ANSWER A CALL USING THE HANDSET
1. Lift the handset. On two-line models, if one
line is already in use, the I Series phone
will automatically select the ringing line.
2. To end the call hang up the handset.
TO ANSWER A CALL USING THE
SPEAKERPHONE
1. With the handset in the cradle, press the
line key associated with the ringing line.
The I Series phone will answer the line selected
with the speakerphone active. You may also:
2. Press the SPEAKER key. The I Series
phone will select the ringing line and
answer with the speakerphone active.
Note: The red SPEAKER LED will indicate that
the speakerphone is active.
USING THE SPEAKERPHONE
If you are talking on the handset and wish
to transfer to the speakerphone, press the
SPEAKER/HSET key, and hang up the handset in
the cradle. The speakerphone will now be active.
11
I SERIES A SERIES PHONES (ANALOG CORDED)
If you are talking on the speakerphone and wish
to transfer to the handset, pick up the handset
from the cradle. The speakerphone LED will go
out and the call can be continued on the handset.
MODELS ONLY)
1. To mute a call, press the MUTE key. The
red MUTE LED will light. You will continue
to be able to hear the other party, but they
will not be able to hear you.
2. Press the MUTE key again to turn off the
mute feature. The MUTE LED will go out.
ONLY)
On two-line telephones, the CONFERENCE key
allows the user to include two other parties in a
three-way conversation. After placing or receiving
a call to/from the first party, place that party on
hold by pressing the HOLD key. Using the second
line, place or receive the second call. Press the
CONF key to join all three callers.
REDIAL
To redial the last telephone number dialed:
1. Lift the handset from the cradle, or press
the SPEAKERPHONE key.
2. Press the REDIAL key. The last number
dialed will be redialed.
Programming
GUEST SERVICE KEYS
Depending on your I Series model, there may
be programmable guest service keys located
above the dialpad. These keys can be used for
one-touch access to commonly dialed numbers
or services. To program these auto-dial keys,
the telephone must be connected to an active
telephone line.
MODELS ONLY)
Programming of these keys is protected from
unauthorized tampering, and employs the use
of hidden programming keys located underneath
the faceplate. With the clear plastic overlay and
faceplate removed from the phone, locate the
STORE key as noted in the phone diagram. This
recessed key is located above number 3 in the
dialpad.
TO PLACE A CALL ON HOLD
To program an auto-dial, or guest service, key:
1. With a call active, press the HOLD key.
2. The red line LED will change to a slow
blink indicating the call is on hold.
TO REMOVE A CALL FROM HOLD
1. Press the line key of the call on hold. This
removes the call from hold.
2. The red line LED will remain illuminated
for the duration of the active call.
CHANGING PHONES AFTER PLACING A CALL
ON HOLD
1. Place the call on hold, as above.
2. Pick up the call at another telephone that
is on the same line.
12
1. Lift the handset from the cradle, or press
the SPEAKERPHONE key.
2. Press the recessed STORE key and release
it.
3. Enter the number or extension to be
programmed.
4. Press the auto-dial key where the number
is to be stored.
5. Repeat steps 3–4 as necessary for
additional auto dial keys.
6. Place the handset back in the cradle,
or press the SPEAKERPHONE key to
disconnect.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES A SERIES PHONES (ANALOG CORDED)
PAUSE KEY
The PAUSE key can be used to provide a timed
pause between dialed digits within a stored
auto dial number. The timing of the pause is
programmable, with the factory default set to
one (1) second. To change the pause timing:
1. Lift the handset or press the
SPEAKERPHONE key (speakerphoneequipped models).
2. Press the STORE key (see diagram on
inside front cover for key location).
3. Press an number from 0 to 5 on the
dialpad. The number selected will be the
pause timing in seconds (for example:
pressing the 3 key will insert a 3-second
pause, etc.).
4. Press the PAUSE key (see diagram for key
location).
5. Press the STORE key. The selected pause
is now inserted into the dialing string.
FLASH KEY
The FLASH key, when programmed behind an
auto dial key, provides a timed line interrupt
typically used for accessing PBX/CO features
such as transfer or conference. The timing of
the hookflash is programmable, with the factory
default set to 600 milliseconds. Some PBXs may
require you to change the hookflash timing from
this default. To change the hookflash timing:
1. Lift the handset or press the
SPEAKERPHONE key (speakerphoneequipped models).
2. Press the STORE key (see diagram on
inside front cover for key location).
3. Select 1–9 on the DTMF pad. The number
selected will be the new flash timing in
hundreds of milliseconds (i.e., pressing the
3 key will reset the flash to 300 ms, etc.).
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
4. Press the FLASH key (see diagram for key
location).
5. Press the STORE key. The selected flash
timing is now programmed.
MESSAGE
Pressing the touch bar automatically turns on
the speakerphone and then dials into a userprogrammed voice mail system to retrieve
messages.
1. Lift the handset.
2. Press the STORE Key.
3. Enter the number to be stored using the
numeric dial pad.
4. Press the red Message Waiting bar to
store.
5. Hang up the handset.
Care and Maintenance
• Keep the telephone dry. If it gets wet, wipe
it dry immediately. Liquids might contain
minerals that can corrode the electronic
circuits.
• Use and store the telephone in a normal
temperature environment. Temperature
extremes can shorten the life of electronic
devices and distort or melt parts.
• Keep the telephone away from excessive
dust and dirt which can cause premature
wear of parts.
• Wipe the telephone with a damp cloth
occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong
detergents to clean the system.
13
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
Unpacking Your Telephone
This package should contain the following:
• Cordless handset
• AC adapter
• Base unit
• User guide
• Ni-MH battery
• Clear plastic overlay
• Rubber battery screw cover
• Phillips screw
• 15-foot, 8-wire cable (with RJ-45 connector)
• 10-foot, 4-wire line cord (with RJ-11 connector)
Installation
CAUTION INFORMATION
• Never install telephone or network wiring
during a lightning storm.
• Never install telephone or Ethernet jacks in
wet locations unless the jack is specifically
designed for wet locations.
• Never touch uninstalled telephone wires or
terminals unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying
telephone and network lines.
PREPARING TO USE THE AC SERIES
1. Prepare to install the battery into the
cordless handset by removing the battery
cover and sliding it off. If cover is secured
with a screw, remove the screw first.
2. Insert the battery connector into the
handset’s connector. The connector is
“keyed” so it only goes in one way. Do not
force the connection.
Note: The handset may “beep” when the battery
is connected. This is not an indication that the
14
telephone is ready to use. To obtain optimal
performance of the telephone, be sure to charge
the battery for 10 to 12 hours.
3. Replace the battery compartment cover
and the retaining screw.
4. Insert the provided rubber screw cover.
5. Turn the telephone base so the back panel
is facing you. Insert either end of the
RJ-45 cable into the jack on the back of the
telephone labeled LINE.
6. Insert the other end of the cable into the
jack on the AC adapter labeled PHONE.
7. Insert one end of the RJ-11 line cord into
the jack on the AC adapter labeled LINE.
8. Insert the other end of this line cord into a
telephone jack.
9. Plug the AC adapter into an unswitched
electrical outlet.
10. Remove the plastic overlay and place the
paper faceplate (supplied separately) over
the keys. Replace the plastic overlay by
hooking the tabs on the overlay into the
recessed slots located on both sides.
11. Place the cordless handset on the base
unit. The handset/base registration
process will occur.
HANDSET/BASE REGISTRATION
PROCEDURE
This procedure establishes an exclusive link
between a specific handset and base, thereby
allowing no other access to this specific base.
To accomplish this procedure, place the handset
on the base in the charging position. The LINE
indicator will blink while the registration process
is occuring. This process only occurs the first
time a handset is placed on the charging cradle
of a new base.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
CHARGING THE BATTERY
The rechargeable Ni-MH battery must be fully
charged before using the phone for the first
time.
It is recommended that the battery be charged for
approximately 10 to 12 hours without interruption
before use. To charge the battery, place the
handset, keypad down, in the base unit. Ensure
that the CHARGE LED on the base lights.
IF THE LED DOES NOT LIGHT
1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is plugged into
an unswitched electrical outlet.
3. Ensure that the handset charging contacts
at the bottom of the handset are making
good contact with the base unit’s charging
contacts.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, it is important to
clean all charging contacts on the handset and
base unit. Use a pencil eraser or other contact
cleaner. Do not use any liquids or solvents.
BATTERY SAFETY INSTRUCTIONS
1. Use only Teledex-approved battery
replacements.
2. Make sure the battery is properly disposed
of.
3. Do not dispose of battery in fire, as it may
explode.
4. Charge the battery only while in the
handset, and only by using the base unit
to charge. Do not attempt to remove
the battery and charge it in a separate
charging unit.
5. Do not short-circuit the battery, as this
may cause it to explode or catch fire.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
CONVERTING FROM DESK TO WALL
MOUNT
The AC Series can be adapted for wall mounting
applications. The conversion is easiest to make
when the handset and cords are not connected.
1. Located on the handset cradle, above
the speaker grill, is the wall/desk mount
clip. Remove this clip by firmly pushing it
upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that
the protruding edge is towards the top of
the phone and replace it in its slot.This
edge will hold the handset when the phone
is mounted on the wall.
3. Turn the telephone over so the bottom is
up, facing you. Place it on a non-abrasive
surface to prevent scratching.
4. Locate and remove the mounting bracket.
Firmly push back and pull up to remove
two of the four retaining tabs.
5. Rotate the mounting bracket 180 degrees
clockwise, so that the mounting eyelet on
the bracket is facing in the same direction
as the other mounting eyelet located on
the bottom of the telephone.
6. Insert the top two retaining tabs of the
mounting brackets into the mounting
bracket slots (located near the middle of
the telephone). Then firmly push down to
insert the retaining tabs on the opposite
side of the mounting bracket.
7. Connect a 15-foot RJ-45 cord into the LINE
jack on the back of the phone.
8. Turn the telephone over, and slide the
telephone down onto the mounting posts
of the wall bracket. Ensure that both
eyelets line up with the mounting posts.
The Ringer Equivalence Number (REN) of this
device is 0.7B.
15
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
3. To end the call, place the handset in the
base unit cradle or press the OFF key on
the handset.
Notice: The Ringer Equivalence Number (REN)
assigned to each terminal device provides an
indication of the maximum number of terminals
allowed to be connected to a telephone interface.
The termination on an interface may consist of
any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5. This
telephone connects to the telephone network
under the connecting arrangement code CA11A.
TO ANSWER A CALL USING THE HANDSET
WHILE IT IS RESTING ON THE BASE
Operation
TO ANSWER A CALL USING THE
SPEAKERPHONE
ADJUSTING SPEAKERPHONE VOLUME
The speakerphone has eight (8) levels. To adjust
speakerphone volume, locate the volume up/
down keys, located on the front of the phone to the
left of the keypad. With the speaker active, press
the “down” arrow key to decrease the volume
level, and press the “up” arrow key to increase it.
ADJUSTING HANDSET RECEIVE
VOLUME
The handset has eight (8) volume levels. To adjust
the handset volume, locate the volume up/down
keys, located on the handset, below the “#” key.
Pressing the UP arrow key will decrease the
volume level, while pressing the DOWN arrow key
will increase it.
RECEIVING A CALL
An audible ring and flickering red LED indicate an
incoming call.
TO ANSWER A CALL USING THE HANDSET
WHILE IT IS NOT ON THE BASE
1. Pick up the handset.
2. Press the line key. The handset will go
“off-hook” answering the phone.
16
1. Pick up the handset from the base.
2. To end the call, replace the handset in the
base unit cradle, or press the ON key on
the handset.
1. Press the line key. The speakerphone will
go “off-hook”, answering the ringing line.
2. Alternatively, press the SPKR key.
3. To end the call, press the SPKR key or the
line key again.
PLACING A CALL
USING THE HANDSET
1. Pick up the handset and select either Line
1 or Line 2. Listen for dial tone and dial the
desired number, or press an auto dial key
to dial a preprogrammed number.
2. After the call is complete, press the key for
the selected line again to end the call.
USING THE SPEAKERPHONE
1. Press a key for either Line 1 or Line 2, or
press SPKR.
2. Listen for dial tone, and dial the desired
number, or press an auto dial key to dial a
preprogrammed number.
3. After the call is complete, press the SPKR
key to end call.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
SELECTING LINE 1 AND LINE 2
The AC Series employs PrimeLine/RingLine
Select, so selecting the correct line is as easy as
lifting the handset. This feature prioritizes the
ringing or idle line and reduces the confusion of
line selection. You may also manually select the
desired line by pressing either Line 1 or Line 2
keys.
TO MUTE THE SPEAKERPHONE
1. Press the MUTE key on the base unit.
The red LED above the MUTE key will
illuminate. The party on the other end will
not be able to hear you when the MUTE
LED is lit.
2. Press the MUTE key again to turn off the
mute feature. The MUTE LED will go out.
REDIAL
ONLY)
The AC Series can automatically redial the last
number dialed. On either the handset or base,
press the REDIAL key to redial the last number.
The CONF key allows for three-way conversations.
Depending on the situation, you may initiate a
conference call using one of these methods:
USING THE HOLD KEY
USER INITIATES TWO CALLS
The HOLD key places the call on hold locally at
the cordless telephone.
TO PLACE A CALL ON HOLD
1. With a call active, press the red HOLD key
on either the handset or base unit.
2. The red line LED will slowly blink,
indicating the call is on hold.
TO REMOVE A CALL FROM HOLD
1. Press the line key of the call on hold, or
the HOLD key again. This will remove
the call from hold, making the call active
again.
2. The red line LED will return to steady
illumination, indicating the line is active.
TO CHANGE PHONES AFTER PLACING A CALL
ON HOLD
1. Place the call on hold as above.
2. Pick up the call at another telephone that
is on the same line. The telephone will
activate the line and remove the hold at
the original telephone.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
1. Place call to first party, then place them on
hold by pressing the HOLD key.
2. Using the second line, place call to second
party.
3. Once that party is on the line, press CONF
to join all three parties.
USER INITIATES ONE CALL
1. After receiving a call from first party, place
them on hold by pressing the HOLD key.
2. Using the second line, place call to the
second party.
3. Once that party is on the line, press CONF
to join all three parties.
USER INCLUDES TWO PARTIES
1. After receiving a call from first party, place
them on hold by pressing the HOLD key.
2. After receiving call from second party,
press CONF to join all three parties.
To terminate a conference call, pressing a line
key will maintain the connection with that line,
while dropping the other line. To terminate the
17
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
call entirely, press either the CONF key or SPKR
key to disconnect both parties.
Programming
AUTO DIAL KEYS
The AC Series has either five (5) or ten (10)
programmable guest service (auto dial) keys,
depending on the model you own. These keys
can be programmed to automatically dial
telephone numbers, or to activate telephone
system features. To program the auto dial keys
(programming can only be done from base unit):
1. With the phone on hook (inactive) and the
faceplate removed, press the recessed
STORE key (see diagram).
2. Enter the desired telephone number (up to
15 digits in length) to be stored. To enter
a “pause” in the number string, press the
REDIAL key as necessary.
3. Press the STORE key again.
4. Press the auto dial key where the number
is to be stored. Programming is now
complete for that auto dial key. To program
additional keys, repeat this process.
PAUSE KEY
The PAUSE key can be used to provide a timed
pause between dialed digits within a stored
auto dial number. The timing of the pause is
programmable, with the factory default set to
one (1) second. To change the pause timing:
1. With the phone on hook (inactive) and the
faceplate removed, press the recessed
STORE key (see diagram).
2. Press the STORE key (see diagram on
inside front cover for key location).
18
3. Press an number from 0 to 5 on the
dialpad. The number selected will be the
pause timing in seconds (for example:
pressing the 3 key will insert a 3-second
pause, etc.).
4. Press the PAUSE key (see diagram for key
location).
5. Press the STORE key. The selected pause
is now inserted into the dialing string.
FLASH KEY
The FLASH key, when programmed behind an
auto dial key, provides a timed line interrupt
typically used for accessing PBX/CO features
such as transfer or conference. The timing of
the hookflash is programmable, with the factory
default set to 600 milliseconds. Some PBXs may
require you to change the hookflash timing from
this default. To change the hookflash timing:
1. With the phone on hook (inactive) and the
faceplate removed, press the recessed
STORE key (see diagram).
2. Press the STORE key (see diagram on
inside front cover for key location).
3. Select 1–9 on the DTMF pad. The number
selected will be the new flash timing in
hundreds of milliseconds (i.e., pressing the
3 key will reset the flash to 300 ms, etc.).
4. Press the FLASH key (see diagram for key
location).
5. Press the STORE key. The selected flash
timing is now programmed.
MESSAGE
Pressing the touch bar automatically turns on
the speakerphone and then dials into a userprogrammed voice mail system to retrieve
messages.
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES AC SERIES PHONES (ANALOG CORDLESS)
1. With the phone on hook (inactive) and the
faceplate removed, press the recessed
STORE key (see diagram).
2. Press the STORE Key.
3. Enter the number to be stored using the
numeric dial pad.
4. Press the red Message Waiting bar to
store.
5. Hang up the handset.
Care and Maintenance
• Use and store the telephone in a normal
temperature environment. Temperature
extremes can shorten the life of electronic
devices and distort or melt parts.
• Keep the telephone away from excessive
dust and dirt which can cause premature
wear of parts.
• Wipe the telephone with a damp cloth
occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong
detergents to clean the system.
• Keep the telephone dry. If it gets wet, wipe
it dry immediately. Liquids might contain
minerals that can corrode the electronic
circuits.
I SERIES ANALOG USER GUIDE
www.teledexeurope.com
19
I SERIES AT SERIES PHONES (ANALOG TRIMLINE)
Unpacking Your Telephone
Features
This package should contain the following:
MESSAGE WAITING INDICATOR
(MODELS AT1101 AND AT1201 ONLY)
• Handset
• Line cord
• Base
• Coiled handset cord
• User guide
Installation
CAUTION INFORMATION
• Never install telephone or network wiring
during a lightning storm.
• Never install telephone or Ethernet jacks in
wet locations unless the jack is specifically
designed for wet locations.
• Never touch uninstalled telephone wires or
terminals unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying
telephone and network lines.
CONNECTING THE PHONE
1. Located on the left side of the phone is a
modular jack. Insert one end of the coiled
handset cord into this jack (you should hear
the coil cord click when properly inserted).
2. Insert the other end of the coiled handset
cord into the modular jack on the bottom
of the handset.
3. Turn the telephone over and insert one end
of the line cord into the jack on the bottom
of the telephone.
4. Route the line cord through the cable
channel in the base of the phone, and
insert the other end into an analog
telephone jack.
WALL MOUNTING
The phone can be easily wall-mounted by placing
it over any standard wall mounting plate and
pressing down.
20
The message waiting indicator is located near the
top of the phone base. Most telephone systems
will turn on this indicator to alert you that there is
a message for you. Follow procedures outlined in
the guest directory for retrieving messages.
BACKLIT KEYPAD
The phone has a backlit keypad for easy of use
in a low-light environment. The backlight is
automatically switched on when the handset is
removed from the base.
ANALOG DATA PORT
The phone is equipped with a standard RJ-11
analog data port on the right side of the phone.
This provides access for a modem or fax machine
to be used on the same line.
Operation
PLACING A CALL
1. Lift the handset. Listen for dial tone. Dial
the desired number.
2. To end the call, hang up by placing the
handset back in the cradle.
RECEIVING A CALL
An audible ring and flickering red message
waiting light (models AT1102 and AT1202 only)
indicate an inbound call. To answer the call, lift
the handset and begin your conversation. To end
the call hang up the handset.
INITIATING A NEW CALL
The Teledex I Series Trimline is equipped with a
hook switch on the handset, so it’s easy to place
a new call without having to return the handset
to the base. To make a new call, simply press
www.teledexeurope.com
I SERIES ANALOG USER GUIDE
I SERIES AT SERIES PHONES (ANALOG TRIMLINE)
the large oval button on the keypad, next to the
volume keys. This performs the FLASH function.
MODELS ONLY)
ADJUSTING THE RING VOLUME
TO PLACE A CALL ON HOLD
Locate the ringer volume control on the back of
the telephone. Slide the switch to the desired
LOW or HI ring volume.
ADJUSTING THE HANDSET VOLUME
In compliance with the Americans with Disabilities
Act, this phone has an adjustable handset volume
feature. To adjust, locate the volume UP and
DOWN keys on the keypad. Press the desired key
to achieve the desired volume level.
REDIAL
To redial the last telephone number dialed, lift the
handset from the cradle and press the REDIAL
key.
TO REMOVE A CALL FROM HOLD
1. Press the line key of the call on hold. This
removes the call from hold.
2. The red line LED will remain illuminated
for the duration of the active call.
CHANGING PHONES AFTER PLACING A CALL
ON HOLD
1. Place the call on hold, as above.
2. Pick up the call at another telephone that
is on the same line.
Care and Maintenance
MUTE KEY
The phone has a momentary MUTE key on the
handset. To mute the handset microphone,
press and hold the MUTE key. To resume your
conversation, simply release the key.
ONLY)
On two-line telephones, the CONFERENCE key
allows the user to include two other parties in a
three-way conversation. After placing or receiving
a call to/from the first party, place that party on
hold by pressing the HOLD key. Using the second
line, place or receive the second call. Press the
CONF key to join all three callers.
I SERIES ANALOG USER GUIDE
1. With a call active, press the HOLD key.
2. The red line LED will change to a slow
blink indicating the call is on hold.
www.teledexeurope.com
• Keep the telephone dry. If it gets wet, wipe
it dry immediately. Liquids might contain
minerals that can corrode the electronic
circuits.
• Use and store the telephone in a normal
temperature environment. Temperature
extremes can shorten the life of electronic
devices and distort or melt parts.
• Keep the telephone away from excessive
dust and dirt which can cause premature
wear of parts.
• Wipe the telephone with a damp cloth
occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong
detergents to clean the system.
21
Telephone: +31 23 5670000
Fax: +31 23 5670009
info@stheurope.com
www.teledexeurope.com
© 2017 teledexeurope.com. Product specifications and descriptions in this document subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising