Panasonic WVCW860_SERIES User manual

Panasonic WVCW860_SERIES User manual
Operating Instructions
WV-CW860
WV-CW864E
ENGLISH
ITALIANO
ESPAÑOL
FRANÇAIS
Model No.
DEUTSCH
Colour CCTV Camera
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH VERSION
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the standards or other normative documents following the provisions
of Directives EEC/73/23 and EEC/89/336.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse
med standarddokument, eller andra normativa dokument
som framstölls i Direktiv 73/23/EEC och 89/336/EEC.
Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten,
overeenkomstig de bepalingen van Richtlijnen 73/23/EEC
en 89/336/EEC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavia standardeja tai
muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien
73/23/EEC ia 89/336/EEC. säädöksiä.
Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse med
den følgende standarder eller andre normative dokumenter
i følge bestemmelserne i direktivene 73/23/EEC og
89/336/EEC.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse med
følgende normer eller andre normgivende dokumenter som
fælger bestemmelsene i direktiven 73/23/EEC og
89/336/EEC.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK), NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Power disconnection. Unit with or
without ON-OFF switches has power
supplied to the unit whenever the
power cord is inserted into the power
source; however, the unit is operational only when the ON-OFF switch
is in the ON position. Unplug the
power cord to disconnect the main
power for all unit.
2
The wires in this mains lead are coloured in accordance with the following code.
Green-and-yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected
to the terminal in the plug which is marked with the letter E or by the
earth symbol I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L or coloured red.
The serial number of this product may be found on the
top of the unit.
You should note the serial number of this unit in the
space provided and retain this book as a permanent
record of your purchase to aid identification in the event
of theft.
Model No.
Serial No.
PREFACE .................................................................................................................. 4
FEATURES ................................................................................................................ 4
■ Camera Cleaning ............................................................................................... 5
■ Preset Data Uploading or Downloading ............................................................ 5
PRECAUTIONS ......................................................................................................... 5
CONSTRUCTION ..................................................................................................... 7
SETUP ...................................................................................................................... 8
■ Setup Menu ....................................................................................................... 8
■ Setup Menu Description .................................................................................... 11
SETTING PROCEDURES .......................................................................................... 16
■ Menu Display ..................................................................................................... 16
■ Presetting ........................................................................................................... 17
■ Deleting Preset Positions ................................................................................... 22
■ Home Position Setting (HOME POSITION) ........................................................ 22
■ Self Return Setting (SELF RETURN) .................................................................. 22
■ Auto Mode Selection (AUTO MODE) ................................................................. 23
■ Auto Pan Key Setting (AUTO PAN KEY) ............................................................ 25
■ Digital Flip Setting (DIGITAL FLIP) .................................................................... 25
■ Local/Remote Setting (LOCAL/REMOTE) ......................................................... 26
■ Special 1 Menu Setting (SPECIAL 1) ................................................................. 26
■ Camera Setting .................................................................................................. 36
■ RS485 Setup ...................................................................................................... 47
INSTALLATION ......................................................................................................... 49
■ Mounting the Camera ........................................................................................ 49
CONNECTIONS ........................................................................................................ 55
SYSTEM CONNECTIONS ......................................................................................... 57
PREVENTION OF BLOOMING AND SMEAR ........................................................... 58
SPECIFICATIONS ..................................................................................................... 58
ACCESSORIES ......................................................................................................... 59
OPTIONAL ACCESSORIES ...................................................................................... 59
APPENDIX ................................................................................................................ 60
3
ENGLISH
CONTENTS
PREFACE
The colour cameras WV-CW860 and WVCW864E are designed for installation in an outdoor video surveillance system.
The camera incorporates the digital signal
processor, pan/tilt mechanism, x22 zoom lens
and RS485 communication interface in a compact outdoor enclosure.
A newly developed 1/4” CCD makes the camera
suitable for use under extremely low illumination
conditions as well as in daylight.
Setup menus allow the camera to perform surveillance tasks by such means as motion detection, digital flip, patrol-learn and privacy zones.
FEATURES
• Outdoor enclosure based on IP66* of
IEC60529 standard
* Waterproof structure resistant to powerful
jetting as classified by the International
Protection code
• Provided with built-in heater and fan
• High quality picture of 752 x 582 pixels
• Minimum illumination of 0.5 lx for colour and
0.03 lx for black/white surveillance
(at AGC ON (HIGH), SENS UP x 2)
• Digital flip allows a 180 ° tilting to trace
objects passing under the camera.
• Privacy zone feature enables users to veil
unwanted zones.
4
• Protocol adaptability to Panasonic's protocol
• Auto black/white mode enables the camera
to switch between C/L and B/W in response
to input lights.
• A run of manual operations is memorized in
the patrol-learn mode for repetitive use in
future.
• Built-in digital motion detector and alarm outputs
• 64 preset positions
• 360 ° panning at a rotation speed of 300 °/s
• Sync selectable between internal, line-lock
or VD2
• Automatic gain control circuit
• Image hold
• Digital noise reduction effect
■ Camera Cleaning
Even if this function is used, noise may be produced on the monitor screen, or the preset position may
deviate in the course of prolonged use.
In such cases, activate the refresh mode on the special 2 menu. (See page 46.)
To use this camera with the WJ-SX550B Matrix Switcher, set the auto cleaning function activated on the
Matrix Switcher side, then clean WV-CW860/WV-CW864E one time a day.
■ Preset Data Uploading or Downloading
To download the preset data from the camera to the controller or upload the downloaded data to the
camera, set the following functions to OFF.
Downloading or uploading the data may not work normally if these functions are set to ON.
• Alarm (See page 32.)
• Preset alarm (See page 35.)
• Cleaning (See page 34.)
• Motion detection (See page 43.)
• Auto mode (See page 23.)
• Self return (See page 22.)
Aim the camera at a motionless object such as a wall, if possible, to download or upload the preset data.
Note: Take notice of the following when uploading the downloaded data to the camera.
• Preset positions may vary. If a preset position has deviated, delete the preset position and set
the correct preset position newly.
• Uploading of WV-CW860/WV-CW864E series preset data to other models (e.g. WV-CS850A
series) may cause an error and failure of the uploading process.
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside.
Ask a qualified service personnel for servicing.
2. Handle the camera with care.
Do not misuse the camera. Avoid striking,
shaking, etc. The camera could be damaged by improper handling or storage.
3. Consult an expert on the load bearing
capacity of the installation surface and
structure. If the surface is not strong
enough, the camera may fall down. Refer
to the product specifications for weights.
4. Do not install the camera in places where
it will be exposed to corrosive gasses,
e.g., in chemical plants, seaside, at swimming pools or the like. Otherwise corrosion of the bracket may cause the camera
to fall down.
5. Use the fall-prevention wires to reduce
the risk of the camera falling down.
Do not detach the fall-prevention wire securing the camera. Otherwise the camera could
fall down, causing injury to persons and
damage to the camera.
5
6. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when it
is dirty.
When the dirt is hard to remove, use a mild
detergent and wipe gently. Care should be
taken not to scratch the dome cover when
wiping it.
Afterwards, wipe off the remaining detergent
with a dry cloth.
7. Never aim the camera at the sun.
Whether or not the camera is in use , never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
8. Never aim the camera at strong light
sources for an extended period of time.
Alight source such as a spot light causes
burn-in on the display screen. Failure to
observe this may cause the image to
become discoloured due to deterioration of
the colour filter in the CCD.
9. Do not aim the camera at the same object
for a long time.
Burn-in of an image may be caused on the
fluorescent screen of CRT.
We recommend that you install the optional
sun shield when the camera is exposed to
direct sunshine where the ambient temperature exceeds +40 °C (104 °F).
Picture quality and camera performance are
not guaranteed until the inside temperature
has risen to –10 °C (14 °F) after turning on
the camera in a cold atmosphere. Wait until
the built-in heater warms up the unit and the
lens and pan/tilt head start searching their
origins.
13. Consumables
Parts having contacts such as the lens-drive
motors, cooling fan motor and slip-rings
inside the camera are subject to wear with
time. Please ask the nearest service centre
about replacement and maintenance of such
parts.
14. Do not install the camera in places subject to vibrations.
Shock absorbers should be installed together with the camera in such places as
bridges, airplanes, vehicles, or near vibration sources.
10. Do not install this camera upside down.
This camera is designed for mounting on the
ceiling or wall. Using this camera installed
upside down, for example, mounted on the
floor, may cause malfunction.
11. If “OVER HEAT” appears on the monitor
screen.
The temperature inside the camera exceeds
the normal level because of a malfunction of
the cooling fan etc. If this happens, turn the
power off immediately and refer servicing to
qualified service personnel.
12. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where
temperatures are between –30 °C and
+50 °C (–22 °F to 122 °F), preferably –10 °C
(14 °F) to +40 °C (104 °F), and humidity is
below 90 %.
The input power source is 220 V to 240 V AC
for WV-CW860 or 24 V AC for WV-CW864E.
6
• Matsushita Electric Industrial Co., Ltd. herewith declares that it will not be liable for any
damage, whether direct or indirect, caused
by using the product for business transaction or security, or malfunctioning of this
product.
CONSTRUCTION
q
w
e
r
i
TANT
INPOR
t
(WV-CW860)
WARNING
t*
(WV-CW864E)
y
u
o
!0
q Alarm Input Connector
y Attachment Pipe
w Alarm Output Connector
u Upper Base
e Video Output Connector
i Fall Prevention Wire
r Data Port
o Enclosure
t Power Cord for WV-CW860
!0 Dome
t* Power Cord for WV-CW864E
7
SETUP
Setup Menu
Setup menus are shown in the diagram below. You can adapt the camera to your requirements by setting
up the respective items in these menus. Menus are built in a hierarchical structure, from the Setup menu
at the top to Manual Mask Area Selection at the bottom.
These menus are described in the following pages for reference prior to setup.
Switches, keys and the joystick are used in the setup operations.
Setup
Menu
PRESET
Menu
Home
Position
Selection
MAP
Menu
Self
Return
Setting
Preset
No. SET
Menu
Auto
Mode
Selection
Auto Pan
Key
Setting
Digital
Flip
ON/OFF
Local/
Remote
Selection
Camera
Menu
Special
1
RS-485
Setup
To
Auto Pan
Setting
Menu
CAMERA ID
Editing
A
Light
Control
Shutter
Speed
Selection
ALC/MANUAL
AGC Mode
Selection
LOW/MID/
HIGH/OFF
Sensitivity
Up
ON/OFF
Sync
INT/LL
White
Balance
Motion
Detector
ON/OFF
AWC
ATW1/ATW2
AF MODE
Selection
To
B
Preset
Setting
Menu
Preset
ID
Setting
Position
Setting
Light
Control
Dwell Time
Setting
CAMERA ID
Display
Position
Scene File
Setting
BLC
OFF
BLC
ON
Manual
Level
Adjustment
(Contrast)
Manual
Mask
Area
Selection
INT
Manual
Selection
LL
Manual
Selection
VD2
Automatic
Selection
Manual
Level
Adjustment
Manual
Level
Adjustment
Manual
Level
Adjustment
ALC/MANUAL
Shutter
Speed
ON/OFF
Preset
ID
Editing
AGC Mode
Selection
LOW/MID/
HIGH/OFF
Electronic
Sensitivity
Up ON/OFF
White
Balance
AWC
ATW1/ATW2
Motion
Detector
ON/OFF
AF Mode
Selection
Manual
Mask
Area
Selection
V-phase
Manual
Adjustment
RS-485
Setup
BLC
OFF
Manual
Level
Adjustment
BLC
ON
Manual
Iris
Adjustment
Manual
Level
Adjustment
Manual
Level
Adjustment
Sensitivity
Level
Adjustment
Mask
Area
Selection
Manual
Mask
Area
Selection
A
Unit
Number
Selection
Demonstration
Display
SubAddress
BAUD
Rate
Selection
Data
Bit
Selection
Parity
Check
Selection
Pedestal
B/W
ON/OFF/AUTO
Selection
Burst
ON/OFF
Selection
Stop
Bit
Selection
Xon/Xoff
Selection
Wait
Time
Selection
Alarm
Data
Selection
Delay Time
Selection
B
Special
2
Privacy Zone
ON/OFF
Zone
Number
Selection
Zone
Parameter
Setting
8
Propo.
P/T
ON/OFF
Area Title
Selection
Direction
Setting
Patrol Learn
Play/Stop
Area Title
Editing
Area Title
Display
Learning
Display
Alarm
IN/OUT
Password
Lock
ON/OFF
Alarm
IN/OUT
Setting
Password
Verification
Password
Registration
Cleaning
ON/OFF
EL-Zoom
ON/OFF
Preset
Alarm
ON/OFF
Image Hold
ON/OFF
Chroma
Gain
Adjustment
Cleaning
Display
AP
Gain
Adjustment
Adjustment
B/W Auto
Duration
Digital Noise
Reduction
Mode selection
LOW1/LOW2/
HIGH1/HIGH2
Refresh
Camera
Reset
B/W Auto
Level
LOW/HIGH
9
The keys (switches) to use for setup are shown in the table below. The joystick on the connected controller may also be used for setup. The table also shows the functions versus the operations of the individual controllers. For details, see the manual for the controller to be used. Switches and controls are abbreviated as SW and CTRL respectively in the table.
[WV-CU550B]
Function/Controller
WV-CU550B
WV-CU360
WV-CU161
WV-RM70
Joystick
FOCUS Switch
ZOOM Switch
ALARM
CAM SETUP
key (for 2 seconds or more)
CAMERA SETUP
key (for 2 seco- See page 16
nds or more)
Close CAM SETUP F4 key
CAM SETUP
key (for 2 seconds or more)
CAMERA SETUP
key (for 2 seco- PROG SW
nds or more)
BUSY
F1
ACK
RESET
Open CAM SETUP See page 16
BACK FORWARD
SEQ SEQ ALT
F2
1
F3
2
3
F4
UP
IRIS
CLOSE OPEN
PRESET
LEFT
4
5
RIGHT
6
AF
AUX
1
DEC INC
–1CAM +1CAM STOP
2
7
8
9
MON
0
CAM
ESC
SET
ZOOM
TELE
FOCUS
NEAR
WIDE
FAR
DOWN
System Controller WV-CU
MON (ESC)
Key
550B
Move the cursor
Joystick
(←, ↑, ↓, →)
Joystick
(←, ↑, ↓, →)
Direction SW
(←, ↑, ↓, →)
Direction SW
(←, ↑, ↓, →)
Select a parameter
Joystick
(←, →)
Joystick
(←, →)
Direction SW
(←, →)
Direction SW
(←, →)
Adjust the level
Joystick
(←, →)
Joystick
(←, →)
Direction SW
(←, →)
Direction SW
(←, →)
Move the camera
direction
Joystick
(←, ↑, ↓, →)
Joystick
(←, ↑, ↓, →)
Joystick
(←, ↑, ↓, →)
Direction SW
(←, ↑, ↓, →)
Zoom & Focus
ZOOM CTRL & ZOOM CTRL & ZOOM CTRL & Direction SW
FOCUS CTRL FOCUS CTRL FOCUS CTRL (←, ↑, ↓, →)
Enter the setting
CAM (SET) key CAM (SET) key CAM (SET) key SET SW
Open a submenu
CAM (SET) key CAM (SET) key CAM (SET) key SET SW
Enter CAM ID &
PRESET ID
display position
SET SW
MON (ESC) key MON (ESC) key MON (ESC) key (for 2 seconds
or more)
Enter MASK
setting
SET SW
MON (ESC) key MON (ESC) key MON (ESC) key (for 2 seconds
or more)
All Reset
F3 key
4+5+6 key
(for 2 seconds
or more)
4+5+6 key
(for 2 seconds
or more)
R+SET+L SW
(for 2 seconds
or more)
F2 key
4+6 key
(for 2 seconds
or more)
4+6 key
(for 2 seconds
or more)
R+L SW
(for 2 seconds
or more)
CAM (SET)
Key
[WV-CU360]
Joystick
FOCUS Switch
ZOOM Switch
OPERATE
LOGIN
SET UP
FUNCTION
SHIFT
CAM SETUP
CAM FUNCTION
ALARM
MONITOR
UNIT
BUSY
CAMERA
PROHIBITED
System Controller WV-CU
360
CAMERA SITE CONTROL
IRIS
CLOSE
ALM RESET
ALM RECALL
OPEN
UP
IRIS RESET
HOME
SX
FOCUS
NEAR
ALM SUSPEND
VTR CAM
B/W
MULTI SCREEN
UNIT
L
FS
EL-ZOOM
FAR
AUTO FOCUS
DEF
R
ZOOM
AUX 2
STILL
WIDE
WIPER
TELE
DOWN
-1 CAM/DEC
+1 CAM/INC
AUX 1
SEQ PAUSE
SEQUENCE
AUTO
MON
BOOST
STOP
PATROL
ESC
PRESET
POSI
CAM
LOGOUT
SET
MON (ESC)
Key
CAM (SET)
Key
[WV-CU161]
Right Switch
Up Switch
Joystick
Left Switch
System Controller WV-CU
OPERATE
ALARM
SHIFT
1
2
3
4
5
6
PATROL
PAY
AUTO
B/W
UP
ALARM
RESET
SUSPEND
CAMERA
SETUP
WIPER
7
8
9
FAR
L
R
FOCUS
AUTO FOCUS
PROGRAM
RESET
AUX2
NEAR
SERUP
CAMERA
FUNCTION
DEF
AUX1
HOME
PRESET
WIDE
SET
CLOSS
0
ESC
TELE
IRIS
DOWN
OPEN
IRIS RESET
PROGRAM
PRESET
SET Key
CAM (SET) Key
Down Switch Open Special 2
[WV-RM70]
Up Switch
Right
Switch
Set Switch
NORMAL PROG
ALARM
RESET
OPERATE REMOTE
SYSTEM
ALARM OFF
Camera Controller WV-RM
Left Switch
10
70
Down
Switch
Notes:
• A changed parameter is entered only when you move the cursor to
another item or open a new menu. If you close the setup menu without
either of the above actions, the changed parameter will not be entered.
• Setting procedures on the following pages are described on the
assumption that the camera is used with the WJ-SX550B Matrix Switcher
and WV-CU550B System Controller.
■ Setup Menu Description
● Presetting
(1) Position (POSITION SET)
Aligns the camera position and focal point by panning, tilting, zooming and focusing.
See page 17 for the setting.
(2) Preset Identification (PRESET ID)
Assigns the name for preset IDs (identification of up to 16 alphanumeric characters) and can be
switched on or off on the monitor screen.
See page 19 for the setting.
(3) Light Control (ALC/MANUAL)
Selects the ALC or MANUAL mode for adjusting the lens iris.
See page 20 for the setting.
(4) Dwell Time (DWELL TIME)
Displays the picture at each camera position for the selected duration.
You can select a preset duration from the menu.
See page 21 for the setting.
(5) Scene File (SCENE FILE)
Stores up to 10 files.
Each file has a set of detailed parameters for the shutter speed, AGC, electronic sensitivity enhancement, white balance, motion detector and AF mode. The scene files can be recalled later to reproduce the parameter settings under the same conditions as stored in the files.
See page 21 for the setting.
● Home Position (HOME POSITION)
The home position is the camera’s basic position.
The camera returns to this position automatically after a specific time.
Following a manual operation. This setting functions only when AUTO MODE is OFF.
See page 22 for the setting.
● Self Return (SELF RETURN)
Self-return is the time-out parameter for returning to the home position.
In ON position, the camera returns to AUTO MODE after a specific time following a manual operation.
See page 22 for the setting.
● Auto Mode (AUTO MODE)
The auto mode is used for setting the movement of the camera.
You can select one of four automatic operation modes and one manual operation mode as follows:
OFF: No automatic operation. The camera can be operated only manually.
SEQ: The camera operates in the sequence of preset positions in numerical order.
SORT: The camera operates in the sequence of preset positions counterclockwise from Pan Starting
Point.
AUTO PAN: The camera automatically turns within the preset panning range.
PATROL: The camera operates in the patrol-learn function.
See page 23 for the setting.
11
● Auto Pan Key (AUTO PAN KEY)
This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the controller.
After this setting, the AUTO key performs as assigned.
Note: The AUTO PAN LED on the controller does not light if a mode other than AUTO PAN is assigned.
● Digital Flip (DIGITAL FLIP)
In ON position, digital flip widens the range to 0 ° - 180 ° by reversing horizontal and vertical scanning
when the camera is tilted through the 90 ° (downright position if the camera is installed on a ceiling). If
PAN LIMIT is in ON position, the tilt range is narrowed from 180 ° to 90 °.
● Local/Remote (LOCAL/REMOTE)
This setting determines whether the camera continues or stops the ongoing auto operation when the controller is turned off.
LOCAL: The camera continues operating in the auto mode when the controller is turned off.
REMOTE: The camera stops operating in the auto mode approx. 1 minute after the controller is turned
off.
See page 26 for the setting.
● Special 1 Menu
(1) Privacy Zone (PRIVACY ZONE)
This setting is used for masking unwanted zones, hiding them from display on the monitor screen. Set
PASSWORD LOCK to OFF(DIS) if you want to change this setting.
Up to 8 zones can be registered. Submenus are provided for zone number selection and parameter
setting. See page 26 for details.
(2) Proportional Pan-Tilt Speed (PROPO. P/T)
If ON is selected, the pan-tilt speed changes automatically corresponding to the zoom ratio. For
example, the pan-tilt speed slows down when the camera zooms in. See page 28 for details.
(3) Area Title (AREA TITLE)
Up to 8 area titles can be assigned to specific scenes on the DIRECTION (NESW) menu or by
alphanumeric (USER) assignment. The area title is displayed under the camera ID on the monitor
screen when the camera turns to a position that has been assigned an area title. See page 28 for
details.
(4) Patrol-learn and Patrol Play (PATROL)
A set of manual operations is stored (LEARN), reproduced (PLAY) or turned inactive (OFF). Patrol
operation stops if SEQ, SORT or AUTO PAN is set to AUTO MODE on the SETUP menu. See page 30
for details.
(5) Alarm Input/Output (ALARM IN/OUT)
Alarm input and output are set on a submenu. Preset positions are assigned to ALARM IN 1 to 4.
When alarm inputs are supplied via the alarm input connector, the camera turns to the respective
positions. Then the camera sends output signals via the alarm output connector or the coaxial cable
to the external devices. The B/W mode may be chosen if light is insufficient. CNT-CLS (Contact
Closure) 1, 2 and COAX ALM OUT are used for alarm output setting. See page 32 for details.
12
(6) Password Lock (PASSWORD LOCK)
This setting controls access to the privacy zone to be free or limited. If PASSWORD LOCK is set to
ON, ON(DIS) or OFF(DIS) for PRIVACY ZONE appears on the SPECIAL 1 menu.
(7) Cleaning (CLEANING)
This is used for refreshing the electro-mechanical contacts built into the camera. Use this function for
maintenance when the camera has been directed at a specific spot or panned over a specific range
for a long time.
(8) Electronic Zoom (EL-ZOOM)
Up to 10-fold electronic zooming is available besides 22-fold optical zooming.
(9) Preset Alarm (PRESET ALM)
Alarm signals are output in the following cases if ON is selected.
• When a preset positioning sequence is completed while AUTO MODE is set to SEQ.
• When a preset positioning sequence is completed while AUTO MODE is set to SORT.
• When positioning to the starting point is completed while AUTO MODE is set to AUTO PAN.
• When the self-return function has returned the camera to its home position.
• When preset positioning is completed by manual operation.
• When positioning to the starting point is completed while PATROL is set to PLAY.
(10) Image Hold (IMAGE HOLD)
The camera picture remains as a still image on the monitor screen or until the camera reaches the
preset position. This function is useful for surveillance via a local area network.
● Camera
(1) Camera Identification (CAMERA ID)
You can use the camera identification to assign a name to the camera. The camera ID consists of up
to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the monitor screen or not. See page 36 for the setting.
(2) Light Control (ALC/MANUAL)
You can select the mode for adjusting the lens iris. There are two modes as follows:
ALC: The lens iris is automatically adjusted according to the brightness of an object.
You can select one of two modes (BLC ON or BLC OFF) of backlight compensation.
Backlight compensation is available in the ALC mode. It eliminates strong background light
which makes the camera picture dark such as a spotlight.
MANUAL: The lens iris is fixed at the value that you have set regardless of the brightness of an
object.
• ALC Mode with BLC ON
An important object in a scene is usually placed in the centre of the monitor screen. By activating this
feature, more photometric weight is given to the centre of the screen than to the edge of the screen
(where bright backlight would most likely be located). In such a case, the object at the centre of the
screen can be still clearly seen even though the backlight may vary.
See page 37 for the setting.
• ALC Mode with BLC OFF
This mode is effective when the main object in the scene is not located in the centre of the screen but
a source of bright light is located near the centre of the scene. In this mode, the picture is divided
into 48 areas that mask the light to keep the clarity of the picture.
13
Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens
iris control in ALC mode.
(3) Shutter Speed (SHUTTER)
You can select a shutter speed from among 1/50 (OFF), 1/120, 1/250, 1/500, 1/1 000, 1/2 000,
1/4 000, and 1/10 000 seconds.
See page 39 for the setting.
(4) Gain Control (AGC)
You can set the gain of an image to automatic adjustment [AGC ON (LOW, MID, HIGH)] or fixed
(AGC OFF).
See page 39 for the setting.
(5) Electronic Sensitivity Enhancement (SENS UP)
The electronic sensitivity enhancement function varies the shutter speed to raise the sensitivity in low
light conditions.
You can select the following shutter speeds for SENS UP.
1/25 seconds (x2), 1/12.5 seconds (x4), 1/8.3 seconds (x6), 1/5 seconds (x10), 1/3.1 seconds (x16),
or 1/1.6 seconds (x32).
See page 39 for the setting.
There are two modes for SENS UP as follows:
AUTO: If you select x32, the sensitivity is raised automatically up to x32.
FIX: If you select x32, the sensitivity is raised to a fixed x32.
Notes:
• Moving objects will appear blurred when shot in electronic sensitivity enhancement mode since
SENS UP is equivalent to reducing the shutter speed in a still picture camera.
• The horizontal and vertical resolution will be lowered in this mode.
• If the iris opening is too small, the SENS UP/AUTO mode will not function.
(6) Synchronization (SYNC)
You can select the internal sync (INT) mode or the line-lock sync (LL) mode. Additionally, this model
accepts the VD2 signal from a specified component. Whenever the VD2 signal is supplied to this
camera, the camera automatically switches to the VD2 sync mode.
When you select the line-lock (LL) mode, you can adjust vertical phase .
See page 40 for the setting.
Important Notices:
The priority of sync modes is given as follows:
1. Multiplexed vertical drive (VD2) (highest)
2. Line-lock (LL)
3. Internal sync (INT) (lowest)
Note: The priority of the automatic sync modes is the same as shown above.
14
(7) White Balance (WHITE BAL)
You can select either of three modes shown below for white balance adjustment:
• Auto-Tracing White Balance (ATW1)
In this mode, the colour temperature is monitored continuously and thereby white balance is set automatically. The colour temperature range for the proper white balance is approx. 2 600 - 6 000 K.
Proper white balance may not be obtained under the following conditions:
1. The colour temperature is out of the 2 600 - 6 000 K range.
2. When the scene contains mostly high colour temperature (bluish) objects, such as a blue sky.
3. When the scene is dim.
In these cases, select the AWC mode.
• Auto-Tracing White Balance (ATW2)
This mode enables the camera to trace the white balance when it is used in an area lit by sodium
lamps.
• Automatic White Balance Control (AWC)
In this mode, accurate white balance is obtained within a colour temperature range of approx. 2 300 10 000 K.
See page 42 for the setting.
(8) Motion Detector (MOTION DET)
The motion detector detects motion in a scene by monitoring changes in the brightness level. You
can select the sensitivity level for the motion on the setup menu.
When the camera detects motion, it sends the alarm signal to the external equipment and stops at its
position for the preset dwell time.
See page 43 for the setting.
(9) Auto Focus (AF MODE)
The camera adjusts the focus automatically by sensing the centre of the picture. S, M and L stand for
the size of the sensing area: Small, Middle and Large.
See page 44 for details.
MANUAL S, M, L: Auto-focus is activated only when the AF key on the controller is pressed.
AUTO S, M, L: Auto-focus is activated automatically while a manual pan, tilt or zoom operation is performed.
Note: If SENS UP is set to ON except x2 FIX or x2 AUTO, the AUTO (S/M/L) mode is disabled and the
MANUAL (S/M/L) mode is automatically selected.
(10) Special 2 Menu (SPECIAL2)
This menu allows you to adjust and set up the following items and functions: chroma level, aperture
level, pedestal level, black and white function, digital noise reduction function and refresh function.
You can also reset your parameters to the factory default settings.
See page 45 for the setting.
● RS485 communication
Refer to the following pages for the communication parameter settings.
• Full/Half duplex (page 54)
• Camera units (96 units max.) (page 52)
• Transmission Speed (2 400 - 19 200 bps) (page 48)
• Termination ON/OFF (page 54)
• Parity bit, Stop bit, Flow control (page 48)
• Reset parameters (page 51)
• Wait time, Delay time, Alarm output (page 48)
15
SETTING PROCEDURES
The following setting procedures are described on the assumption that this model is used in combination
with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case a controller other than
the WV-CU550B is used, refer to the table on page 10.
■ Menu Display
● Setup Menu Display
WV-CU550B
1. Select the camera number you want to set up and a monitor to
display SET UP MENU.
2. Display the D4 menu on the LCD by pressing the appropriate cursor buttons.
3. Press the F1 button.
SET UP MENU appears on the monitor screen.
4. To close SET UP MENU, press the F4 button.
WV-CU360
Press the CAM SETUP key for 2 seconds or more to open the
SETUP menu.
WV-CU161
Press the CAMERA SETUP key for 2 seconds or more to open the
SETUP menu.
D4 menu
Camera Set Up Menu
On
Exit
F1 F2
F3 F4
Camera Set Up Menu
Res A.Res Exit
F1 F2
F3 F4
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
WV-RM70
1. Turn the MODE SELECTION switch to NORMAL or ALARM OFF.
2. Press the PROG switch for 2 seconds or more to open the
Program Menu.
3. Move the cursor to Camera Set Up Menu, and press the SET
switch to open the SETUP MENU.
● Submenu Display
The items marked O can be selected/changed on the submenu.
• Move the cursor to an item with the O mark and press the CAM
(SET) key. The submenu appears.
16
Submenu
(for RS485 setup)
** RS485 SET
UNIT NUMBER
SUB ADDRESS
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
UP **
1
----19200
8
NONE
1
NOT USE
OFF
AUTO2
---
■ Presetting
Setup menu
● Preset Menu Display
1. Displaying the preset menu directly
(1) Move the cursor to PRESET 1 O and select the position number by moving the joystick to the right or left.
(2) Press the CAM (SET) key.
The preset setting menu appears on the monitor screen.
2. Displaying the preset menu from the PRESET NUMBER SET menu
(1) Move the cursor to MAP O and press the CAM (SET) key.
The PRESET NUMBER SET menu appears on the monitor
screen.
(2) Move the cursor to the position number to be set and press
the CAM (SET) key.
The preset setting menu appears on the monitor screen. To
display position number 33-64, move the cursor to “33-64” in
the lower left of the screen and press the CAM (SET) key.
Notes:
• The * mark indicates that the position number has been preset.
• The character H refers to the home position.
• The second line from the bottom shows the preset ID corresponding to the selected number. “DOOR” next to “ID” in the
example shown right is for preset position number 1.
• Preset numbers 1 to 4 are linked to alarm inputs 1 to 4. If
alarm input 1 comes in, the camera turns to preset position 1,
or to other positions according to alarm input 2, 3 or 4.
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
PRESET NUMBER SET menu
(1-32)
** PRESET NUMBER SET **
1
5
9
13
17
21
25
29
2
6
10
14
18
22
26
30
ID:DOOR
33-64 RET
4
8
12
16
20
24
28
32
PRESET NUMBER SET menu
(33-64)
** PRESET NUMBER SET **
33
37
41
45
49
53
57
61
● Position Setting (POSITION SET)
3
7
11
15
19
23
27
31
34
38
42
46
50
54
58
62
35
39
43
47
51
55
59
63
36
40
44
48
52
56
60
64
ID:
1-32 RET
1. Move the cursor to POSITION SET on the preset setting menu and
press the CAM (SET) key.
The position setting menu appears.
Preset setting menu
PRESET NO. 1*
2. To Set Panning/Tilting Positions
(1) For PAN/TILT, move the cursor to PUSH SET and press the
CAM (SET) key. The PAN/TILT setting menu appears.
(2) Select panning/tilting positions by using the joystick, and
press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
17
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
ON
ALC
10S
OFF
••••••••|
L
H
DEL
PAN/TILT setting menu
Position setting menu
** POSITION 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
** POSITION 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
U TILT D/L PAN R
PAN OFFSET SET ← −0.0 →
PAN OFFSET SET ←
RET
FLOOR1
DOOR
RET
FLOOR1
DOOR
−0.0 →
3. Pan Offset
If the camera is replaced with a new one, the pan offset function
is used to adjust its positions to be the same as before except
patrol setting.
The system controller can download or upload the preset position
data.
Caution: The preset data for other cameras (WV-CS850A for
example) is incompatible with WV-CW860's. WV-CW860's
preset data will be destroyed if you upload the conventional
data. If this happened, reset the WV-CW860/WV-CW864E to
the default settings. Download the factory settings into the
controller and upload the correct preset data newly to the initialized WV-CW860/WV-CW864E.
(1) Display the PRESET NUMBER SET menu.
(2) Select a position number for the picture to be most enlarged
among the numbers by using the joystick. Then press the
CAM (SET) key. The position setting menu appears.
(3) Move the cursor to PAN OFFSET SET and select the right or
left arrow by using the joystick.
(4) Press the CAM (SET) key until the desired offset value
appears.
(5) Move the cursor to an item other than PAN OFFSET SET, and
press the MON (ESC) key.
Notes:
• Further adjustment of the other positions is unnecessary. This
adjustment applies to all other positions.
• Make sure to move the cursor before pressing the key in step
5. Otherwise the settings will be ignored.
• Retry the loading when the camera fails to upload or download the data.
PRESET NUMBER SET menu
(1-32)
4. To Set the Lens Zoom and Focus Positions
(1) Move the cursor to PUSH SET for ZOOM/FOCUS and press
the CAM (SET) key. The ZOOM/FOCUS setting menu
appears.
(2) Select a zoom position by moving the zoom control up and
down, and a focus position by moving the focus control up
and down, and then press the CAM (SET) key.
The positions are set and the screen returns to the position
setting menu.
Notes:
• When the camera is used at a nearly horizontal angle, the
focus may not be adjustable to a high level of accuracy.
• If you move the cursor to the position number and move the
joystick right or left, the position number can be selected.
The selected preset position number can also be set after
pressing the CAM (SET) key.
• The preset and camera IDs appear in the lower-left corner of
the position setting menu after setting them.
U ZOOM D/L FOCUS R
PAN OFFSET SET ← −0.0 →
5. Move the cursor to RET and press the CAM (SET) key to return to
the preset setting menu.
18
** PRESET NUMBER SET **
1
5
9
13
17
21
25
29
2
6
10
14
18
22
26
30
ID:DOOR
33-64 RET
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
Position setting menu
** POSITION 1 **
PAN/TILT
→PUSH SET
→PUSH SET
ZOOM/FOCUS
PAN OFFSET SET ←
−0.0 →
RET
FLOOR1
DOOR
Position setting menu
** POSITION 1 **
PAN/TILT
→PUSH SET
→PUSH SET
ZOOM/FOCUS
PAN OFFSET SET ←
−0.0 →
RET
FLOOR1
DOOR
ZOOM/FOCUS setting menu
** POSITION 1 **
→PUSH SET
PAN/TILT
→PUSH SET
ZOOM/FOCUS
RET
FLOOR1
DOOR
Position setting menu
** POSITION 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
PAN OFFSET SET ←
RET
FLOOR1
DOOR
−0.0 →
● Preset Identification Setting (PRESET ID)
Preset setting menu
1. Move the cursor to PRESET ID on the preset setting menu and
select ON or OFF by moving the joystick to the right or left.
The factory default setting is OFF.
ON: Preset ID appears on the monitor screen.
OFF: Preset ID does not appear.
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
2. Press the CAM (SET) key to display the preset ID setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using the joystick,
and press the CAM (SET) key.
(2) The selected character appears in the editing area. (The
pointer in the editing area moves to the right automatically at this moment.) To enter a blank, select SPACE.
(3) Repeat the above procedure until all characters are
entered.
ON
ALC
10S
OFF
••••••••|
L
H
DEL
Preset ID setting menu
Character Cursor
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
Character
Area
Command
Editing
Area
Pointer
To Copy a Preset ID from Another Position
(1) Move the cursor to COPY and press the CAM (SET) key. The
preset ID in the preceding position is immediately shown.
Each consecutive pressing of the CAM (SET) key displays the
ID preceding the one currently displayed.
(2) Display the most prospective ID.
(3) Follow the step “To Change an Entered Preset ID” if necessary.
To Change an Entered Preset ID
(1) Move the pointer to the character to be edited in the editing
area by using the joystick.
(2) Select a new character by using the joystick.
(3) Press the CAM (SET) key to determine the Preset ID.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
To Delete an Entered Preset ID
Move the cursor to RESET and press the CAM (SET) key.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
19
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM (SET) key. The
display position set menu appears.
(2) Move the ID to the desired position by using the joystick, and
press the MON (ESC) key. The display position is set and the
monitor screen returns to the preset ID setting menu.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
Display position set menu
FLOOR 1
DOOR
To Enter the Next ID without Returning to the Preset Setting
Menu
(1) In the preset ID setting menu, move the cursor to the top line
and select a desired position number by moving the joystick
to the right or left.
(2) Enter, copy, change or delete the ID as described above.
PRESET NO. 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
COPY POSI RET RESET
DOOR............
To Return to the Preset Setting Menu
Move the cursor to RET and press the CAM (SET) key.
● Light Control Setting (ALC/MANUAL)
1. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
moving the joystick to the right or left.
The factory default setting is ALC.
ALC: The lens iris is automatically adjusted to suit the brightness
of the object.
MANUAL: The lens iris is fixed at the set value regardless of the
brightness of the object.
2. In case of ALC O
Press the CAM (SET) key. The backlight compensation menu
appears on the monitor screen. See page 37 for the setting.
3. In case of MANUAL O
Press the CAM (SET) key. The setting menu appears on the monitor screen. Set the lens iris level as desired by moving the joystick
to the right or left.
20
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
ON
ALC
10S
OFF
••••••••|
L
H
DEL
Manual setting menu
** MANUAL CONT **
IRIS
RET
••••|••••
CLOSE
OPEN
● Dwell Time (DWELL TIME)
Preset setting menu
• Move the cursor to DWELL TIME and set a dwell time by moving
the joystick to the right or left. The factory default setting is 10S.
Dwell time changes as follows:
2S
3S
5S
10S
30S
1MIN
2MIN
3MIN
4MIN
S stands for second(s), and MIN stands for minute(s).
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
ON
ALC
10S
OFF
••••••••|
L
H
DEL
Preset setting menu
● Scene File Setting (SCENE FILE)
1. To set a scene file number
Move the cursor to SCENE FILE and select a scene file number (1
to 10, or OFF) by moving the joystick to the right or left. The factory default setting is OFF. No scene file is selected at OFF.
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
2. To set scene file details
Move the cursor to a scene file number and press the CAM (SET)
key. The setting menu appears.
See the pages below for the setting.
Shutter speed: page 39
AGC: page 39
Electronic sensitivity enhancement: page 39
White balance: page 41
Motion detector: page 43
Auto focus: page 44
● Preset Speed Setting (PRESET SPEED)
• Move the cursor to PRESET SPEED and select a speed by moving
the joystick to the right or left.
● To Return to the Preset Number Set Menu
• Move the cursor to RET and press the CAM (SET) key. The PRESET NUMBER SET menu appears with the * mark on the right of
the preset position number.
● To Return to the Setup Menu
• Move the cursor to RET and press the CAM (SET) key.
ON
ALC
10S
1
••••••••|
L
H
DEL
Scene file setting menu
** SCENE FILE 1 **
SHUTTER
AGC
SENS UP
WHITE BAL
MOTION DET
AF MODE
OFF
ON(MID)
X2 AUTO
ATW1
OFF
MANUAL S
RET
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
ON
ALC
10S
OFF
••••••••|
L
H
DEL
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
ON
ALC
10S
OFF
••••••••|
L
H
DEL
PRESET NUMBER SET menu
** PRESET NUMBER SET **
1*
2
5
6
9
10
13
14
17
18
21
22
25
26
29
30
ID:DOOR
33-64 RET
21
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
■ Deleting Preset Positions
Setup menu
1. Move the cursor to PRESET 1 and select the position number to
be deleted by using the joystick.
2. Press the CAM (SET) key to display the preset setting menu.
** SET UP MENU **
PRESET 1*
MAP
HOME POSITION OFF
SELF RETURN
OFF
AUTO MODE
OFF
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
Preset setting menu
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET
3. Move the cursor to DEL and press the CAM (SET) key.
This deletes the preset position and the PRESET NUMBER SET
menu appears. The * mark on the right of the number disappears.
Note: Your selected preset number is cancelled only in the SEQ
and SORT mode. The previously set parameters (for PAN,
TILT positions, etc.) are not changed. If you want to change
these parameters, you must set them again.
■ Home Position Setting
(HOME POSITION)
■ Self Return Setting (SELF RETURN)
To set a time-out parameter for return to the home position
• Move the cursor to SELF RETURN and select a return time by
moving the joystick to the right or left.
The factory default setting is OFF.
Return time changes as follows:
OFF
2MIN
3MIN
60MIN
5MIN
30MIN
10MIN
20MIN
MIN stands for minute(s).
Note: The camera will return to the auto mode if that is set to SEQ,
SORT, AUTO PAN or PATROL when a specific time has
elapsed after a manual operation.
22
DEL
PRESET NUMBER SET menu
** PRESET NUMBER SET **
1
5
9
13
17
21
25
29
2
6
10
14
18
22
26
30
ID:DOOR
33-64 RET
3
7
11
15
19
23
27
31
4
8
12
16
20
24
28
32
Setup menu
1. To set a position number for the home position
Move the cursor to HOME POSITION and select a desired position number by moving the joystick to the right or left.
The factory default setting is OFF.
2. Select OFF if you are not using the home position function.
Note: This setting functions only when AUTO MODE is set to OFF.
1MIN
ON
ALC
10S
OFF
••••••••|
L
H
** SET UP MENU **
PRESET 1
MAP
HOME POSITION 15
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
10MIN
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
■ Auto Mode Selection (AUTO MODE)
1. To set auto mode
Move the cursor to AUTO MODE and select a mode by moving
the joystick to the right or left.
The factory default setting is OFF.
Modes change as follows:
OFF
SEQ
SORT
AUTO PAN
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
AUTO PAN
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
PATROL
AUTO PAN setting menu
** AUTO PAN **
OFF: No automatic operation. The camera can be operated only
manually.
SEQ: The camera operates in the sequence of preset positions in
numerical order.
SORT: The camera operates in the sequence of preset positions
counterclockwise from the Pan/Tilt starting point.
AUTO PAN: The camera automatically turns within the preset
panning range.
PATROL: The camera operates in the patrol-learn function.
2. When the AUTO PAN mode is selected, set details as follows:
Move the cursor to AUTO PAN O and press the CAM (SET) key
to display the AUTO PAN setting menu.
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
START
END
••••|••••
L
H
OFF
OFF
1S
RET
** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
START
END
••••|••••
L
H
OFF
OFF
1S
RET
3. To set a panning starting point and panning endpoint
Follow the steps below.
(1) Move the cursor to POSITION and press the CAM (SET) key.
The cursor moves to START.
(2) Move the joystick to the right or left to select a panning starting point and press the CAM (SET) key.
This determines the starting point and the cursor moves to
END.
(3) Move the joystick to the right or left to select a panning endpoint and press the CAM (SET) key.
This determines the endpoint and the cursor moves to POSITION.
** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RET
** AUTO PAN **
POSITION
SPEED
4. To set a panning speed
Move the cursor to SPEED, and set a panning speed by moving
the joystick to the right or left .
The panning speed increases when the joystick is moved to the
right, and decreases when it is moved to the left.
Caution: If the panning range is changed after the camera has not
panned for a long time or has been panning in the same panning
range, the picture may not be clear or noise may appear. In this
case, pan the camera fully several times.
If this does not eliminate the problem, refer servicing to qualified
service personnel.
23
START
END
••••|••••
L
H
OFF
OFF
1S
PAN LIMIT
ENDLESS
DWELL TIME
RET
START
END
••••|••••
L
H
OFF
OFF
1S
5. To set pan limit ON/OFF
Endpoint
Move the cursor to PAN LIMIT and select ON or OFF by movCamera
ing the joystick to the right or left.
Start-end
range of
The factory default setting is OFF.
ON: Manual pan is limited from the starting point to the end- auto pan
point specified by position setting. Set ENDLESS to OFF
before PAN LIMIT is set to ON.
Starting point
OFF: Manual pan is not limited.
Self-end
range of
pan limit
Note: When ON is selected for PAN LIMIT, manual pan moves the
camera away from the other side (PAN LIMIT) of the start-end
range.
6. To set ENDLESS to ON/OFF
Move the cursor to ENDLESS, and select ON or OFF by moving
the joystick to the right or left.
The factory default setting is OFF.
ON: The camera pans from the starting point to the endpoint, and
keeps rotating in the same direction to return to the starting
point. Set PAN LIMIT to OFF before ENDLESS is set to ON.
OFF: The camera pans from the starting point to the endpoint,
and rotates backward to the starting point.
This movement is repeated over and over.
7. To set a dwell time
Move the cursor to DWELL TIME and select a dwell time by moving the joystick to the right or left.
The factory default setting is 1S.
Dwell time changes as follows:
** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
START
END
••••|••••
L
H
OFF
ON
1S
RET
** AUTO PAN **
0S
30S
1S
20S
2S
10S
3S
POSITION
5S
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
Notes:
• When the panning, tilting, zooming or focusing in the SEQ,
SORT or PATROL mode is controlled manually, the Auto
mode function should be cancelled.
To activate the auto mode, select the desired auto mode
again or set a time for SELF RETURN in the SET UP menu.
• When 0S is selected, the camera stops without dwelling and
starts.
• Auto refreshing may be activated during the patrol play or the
auto mode to calibrate the lens position.
24
RET
START
END
••••|••••
L
H
OFF
OFF
1S
■ Auto Pan Key Setting
(AUTO PAN KEY)
Setup menu
This is used for assigning one of the following auto functions to the
AUTO key on the controller. Pressing the AUTO key activates the
assigned function after this setting.
• Move the cursor to AUTO PAN KEY and select an auto function by
moving the joystick to the right or left.
The factory default setting is AUTO PAN.
Mode changes as follows:
AUTO PAN
SEQ
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
SORT
PATROL
AUTO PAN: Assigns the auto panning function to the key.
SEQ: Assigns the sequence function to the key.
SORT: Assigns the sort function to the key.
PATROL: Assigns the patrol play function to the key.
Note: Auto pan LED on the controller does not light if a function
other than the auto pan function is assigned. The auto pan
function cannot be stopped with the AUTO PAN key.
■ Digital Flip Setting (DIGITAL FLIP)
• Move the cursor to DIGITAL FLIP and select ON or OFF by moving the joystick to the right or left.
The factory default setting is ON.
OFF: Tilt range is limited from 0 ° to 90 °.
ON: The digital flip function allows the tilt angle to widen up to
180 °. The image on the monitor screen is flipped horizontally
and vertically at the tilt angle of approx. 135 ° (If the camera is
installed on a ceiling).
Note: Tilt range narrows from 180 ° to 90 ° if PAN LIMIT is set to
ON.
Notes:
• Digital flip functions while moving the joystick downwards. In case
of moving the joystick to other directions, it does not function.
• When OFF is selected for DIGITAL FLIP, the following operations
are required to move the camera 180 ° vertically.
1) Move the joystick downwards to aim the camera down.
2) Move the joystick to the right or left to rotate the camera 180 °
horizontally.
3) Move the joystick upwards.
• To set preset position directly from the WV-CU360, WV-CU550B
or WV-CU161 System Controller, it is temporarily required setting
both the electronic zoom function and digital flip function to OFF.
Tilt range setting is disabled between 90 ° and 180 °.
25
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
■ Local/Remote Setting
(LOCAL/REMOTE)
• Move the cursor to LOCAL/REMOTE, and select LOCAL or
REMOTE by moving the joystick to the right or left.
The factory default setting is LOCAL.
Note: The REMOTE mode does not work when the WV-RM70,
WV-CU360, WV-CU161, WJ-FS616 or WV-CU550 series is
connected. Make sure that LOCAL mode is selected in this
case.
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
■ Special 1 Menu Setting (SPECIAL 1)
● Privacy Zone (PRIVACY ZONE)
Up to 8 unwanted zones can be masked on the monitor screen.
1. Move the cursor to PRIVACY ZONE and select ON (ENB) or OFF
(ENB) by moving the joystick to the right or left. Press the CAM
(SET) key to display the ZONE NUMBER setting menu.
The factory default setting is OFF (ENB).
ON (ENB): Preset privacy zones are veiled on the monitor screen.
OFF (ENB): The veiling function does not work.
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
ZONE NUMBER setting menu
** ZONE NUMBER 1*/8 **
Note: If ON(DIS) or OFF(DIS) appears for PRIVACY ZONE, the
steps from 2 onward are not applicable. Select OFF for PASSWORD LOCK to take the following steps.
RET
2. Select a zone number by moving the joystick to the right or left,
and press the CAM (SET) key.
• A zone number followed by * (asterisk) indicates that the zone
has already been registered.
• When a zone number having no * is selected, the picture is
zoomed out fully.
• When a registered zone number is selected, the camera
moves to the preset position. Note that if you move PAN/TILT,
ZOOM/FOCUS or ZONE SCALE in that position, the registered zone number having “*” is cancelled.
• The zone frame appears in the centre of the screen if 3 or
fewer mask areas exist in that picture and if the zone number
is not registered yet.
• The privacy zone may appear on the monitor screen depending on the direction of the camera.
• The privacy zone function will not work at start-up immediately after turning the power on.
26
ZONE setting menu
** ZONE NUMBER 1*/8 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
ZONE SCALE
SET DEL
RET
••••|••••
–
+
ZONE setting menu
** ZONE NUMBER 1*/8 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
ZONE SCALE
SET DEL
RET
••••|••••
–
+
3. To register a new zone
3-1 For PAN/TILT, move the cursor to PUSH SET and press the
CAM (SET) key.
PAN/TILT setting menu
** ZONE NUMBER 1*/8
PAN/TILT
→PUSH
ZOOM/FOCUS
→PUSH
U TILT D/L PAN
**
SET
SET
R
3-2 Adjust the pan and tilt position so that the desired position
comes into the zone frame by using the joystick.
Note: Zone setting is not available while the zone frame is not
shown, for example, when the camera is tilted downward by
more than 45 °.
3-3 For ZOOM/FOCUS, move the cursor to PUSH SET , and press
the CAM (SET) key.
ZONE SCALE
SET DEL
RET
ZOOM/FOCUS setting menu
** ZONE NUMBER 1*/8
PAN/TILT
→PUSH
ZOOM/FOCUS
→PUSH
U ZOOM D/L FOCUS
ZONE SCALE
SET DEL
RET
3-4 Adjust zoom and focus, and press the CAM (SET) key.
Zoom can be adjusted within the range of 1 to 10 magnifications.
3-5 Move the cursor to ZONE SCALE, and move the joystick to
the right or left to adjust the zone frame. Press the CAM (SET)
key after the adjustment.
Moving the joystick in the L direction decreases the zone
frame, and moving it in the H direction increases it. However,
the aspect ratio is fixed at 3 to 4.
The privacy zone setting has been completed.
The menu returns to the ZONE NUMBER setting menu. If DEL
is selected, zone setting is released and the ZONE NUMBER
setting menu appears.
Notes:
• To complete new settings and repeat other settings, move the
cursor to SET and press the CAM (SET) key. The ZONE NUMBER setting menu returns.
• To cancel new settings and return to the SPECIAL 1 menu,
move the cursor to DEL and press the CAM (SET) key. New
settings are not registered.
• To complete new settings and return to the SPECIAL 1 menu,
move the cursor to RET and press the CAM (SET) key.
27
••••|••••
–
+
**
SET
SET
R
••••|••••
–
+
ZONE SCALE setting menu
** ZONE NUMBER 1*/8 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
ZONE SCALE
SET DEL
RET
••••|••••
–
+
● Proportional Pan/Tilt (PROPO. P/T)
• Move the cursor to PROPO. P/T and select either ON or OFF by
moving the joystick to the right or left.
Factory default setting: ON
ON: Pan/tilt speed is in inverse proportion to the zoom ratio as follows:
Zoom ratio
Speed level
x1
7 (fastest)
x2
5
x4
3
x8
1
x15 or more
0 (slowest)
* The speed level values are approximate.
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
OFF: The speed is constant at the fastest level regardless of the
zoom ratio.
● Area Title (AREA TITLE)
Special 1 menu
Up to 8 area titles can be added in specific positions.
1. Select ON (NESW), ON (USER) or OFF by moving the joystick to
the right or left.
ON (NESW): An area title is displayed for indicating the camera
direction: North (N), North-East (NE), East (E), South-East
(SE), South (S), South-West (SW), West (W) and North-West
(NW).
ON (USER): A user customized area title appears in a maximum
of 16 characters.
OFF: Area tittle does not appear.
Factory default setting: ON (USER)
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
2. Turn the camera north by using the joystick, and press the CAM
(SET) key. The origin of the direction (North) is set.
Note: Area titles are highlighted until the origin is set.
28
OFF
OFF
ON
OFF
OFF
AREA TITLE (NESW) setting menu
** DIRECTION(NESW) **
→PUSH SET
PAN/TILT
→PUSH SET
ZOOM/FOCUS
POSI
2. Press the CAM (SET) key. A submenu appears except when OFF
is selected.
When ON (NESW) is selected:
1. Move the cursor to PUSH SET for PAN/TILT, and press the CAM
(SET) key. PAN/TILT is highlighted and “U TILT D/L PAN R”
appears.
1 **
OFF(ENB)
ON
ON(NESW)
STOP
+
N
RET
PAN/TILT setting menu
** DIRECTION(NESW) **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
POSI
U TILT D/L PAN R
+
N
RET
3. Move the cursor to PUSH SET for ZOOM/FOCUS, and press the
CAM (SET) key. ZOOM/FOCUS is highlighted and “U ZOOM D/L
FOCUS R” appears.
ZOOM/FOCUS setting menu
** DIRECTION(NESW)
PAN/TILT
→PUSH
→PUSH
ZOOM/FOCUS
POSI
U ZOOM D/L FOCUS
4. Adjust the zoom or focus by using the joystick.
5. Move the cursor to POSI O, and press the CAM (SET) key. The
area title position appears on the monitor screen. If needed,
change the display position by using the joystick, and press the
MON (ESC) key.
An area title always appears under the camera ID.
If the camera ID and an area title are set to be shown in separate
positions, the area title appears above the camera ID.
6. Move the cursor to RET, and press the CAM (SET) key. The SPECIAL 1 menu appears again.
**
SET
SET
R
+
N
RET
Display Position setting menu
FLOOR 1
N
Setting [ON (USER)]
If ON (USER) is selected on the SPECIAL 1 menu, the Area Title
selection menu appears. The screen has a number column and
title column above RET and RESET.
Note: An area number followed by an asterisk * has already been
preset.
1. To select a camera direction, move the cursor to the desired number, and press the CAM (SET) key. The direction menu of the
selected number appears.
2. Adjust PAN/TILT, ZOOM/FOCUS and display the position in the as
same way as AREA TITLE, DIRECTION (NESW). See page 28.
3. To add a user-customized title, move the cursor to the title of the
desired number, and press the CAM (SET) key. The AREA TITLE
menu of the selected number appears.
Area Title Editing
1. Move the cursor to the desired character in the character field
using the joystick, and press the CAM (SET) key.
2. The selected character appears in the editing field and the blinking cursor moves one position to the right.
3. Repeat steps 1 and 2 until one area title is completed.
4. Move the cursor to POSI O, and press the CAM (SET) key. The
area title appears on the monitor screen. If needed, change the
display position by using the joystick, and press the MON (ESC)
key.
29
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
AREA TITLE (USER) selection menu
** AREA TITLE(USER) **
1*
NORTH
2
3
EAST
4
SOUTH-EAST
5
SOUTH
6
SOUTH-WEST
7
8
NORTH-WEST
RET
RESET
DIRECTION (USER) setting menu
** DIRECTION(USER) 1 **
PAN/TILT
→PUSH SET
ZOOM/FOCUS
→PUSH SET
+
NORTH
RET
DEL
To Quit Editing
• To return to the AREA TITLE menu, move the cursor to RET, and
press the CAM (SET) key.
• To cancel one area title, move the cursor to RESET in the AREA
TITLE menu, and press the CAM (SET) key.
• To return to the SPECIAL 1 menu, move the cursor to RET, and
press the CAM (SET) key.
• To erase all the area titles, move the cursor to RESET in the AREA
TITLE (USER) selection menu, and press the CAM (SET) key.
AREA TITLE menu
AREA TITLE 1*
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
POSI RET RESET
................
Display Position setting menu
Notes:
• An area title appears under the camera ID if both are set in
the same position. If the setting is different, they appear in the
area title position.
• In case of sharing a common subject in a scene of other camera number, the nearest area title appears while the camera
direction deviates within 45 ° from the set position. If two or
more area numbers are set in the same position, the title of
the highest number appears.
FLOOR 1
NORTH
● Patrol-learn and Patrol Play (PATROL)
A routine of manual operations can be stored for 30 seconds at the
maximum and reproduced repetitively.
1. Set the following parameters for the patrol-learn starting position.
These parameters are stored when the patrol-learn mode starts.
• PAN/TILT/ZOOM/FOCUS
• IRIS
• SHUTTER
• AGC
• SENS UP
• WHITE BALANCE
• IMAGE HOLD
• AREA TITLE
• DIGITAL FLIP
• PRIVACY ZONE
• CAMERA ID
• PROPO.PT
• PAN LIMIT
• BURST
• CLEANING
After starting the patrol-learn, the following manual operations are
stored.
• PAN/TILT/ZOOM/FOCUS operation
• IRIS operation
• Preset positioning
2. Open the SET UP menu and move the cursor to SPECIAL 1. For
PATROL, select LEARN, PLAY or STOP by moving the joystick to
the right or left.
The factory default setting is STOP.
LEARN: A series of manual operations is stored.
PLAY: Stored operations are reproduced.
STOP: LEARN or PLAY is not activated.
30
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
Patrol-learn with a Controller Having the PATROL Key
1. Press the PATROL LEARN key and PROGRAM key simultaneously to start patrol-learn. The setup menu displays “LEARNING”, and
the starting points are stored.
2. Operate patrol-learn manually. The operation data is stored.
3. To stop patrol-learn, press the PATROL STOP and PROGRAM key
simultaneously.
PATROL LEARN
LEARNING
Patrol-learn with a Controller not Having the PATROL Key
1. Select patrol-learn in the setup menu, and then close the menu.
Starting points are stored and “LEARNING” appears on the monitor screen.
2. Operate patrol-learn manually.
3. Open the SET UP menu to stop learning.
Notes:
• It is recommended to set PAN LIMIT to ON for patrol-learn. Otherwise PAN LIMIT is invalid in
playback.
• If the power fails during the patrol-learn mode, start the patrol-learn function again from the starting point.
• LEARN also stops 30 seconds after starting if the memory is full.
• Auto refreshing may be activated during the patrol play mode or the auto mode to calibrate the
lens position.
Patrol Play with a Controller Having the PATROL Key
1. Press the PATROL PLAY key. The camera turns to the starting point and reproduces the operations
stored in the memory. Iris operation is valid only in the playback mode.
2. Press the PATROL STOP key and PROGRAM key simultaneously to stop playback or press any manual operation key (e.g., PAN/TILT/ ZOOM/FOCUS) except the iris keys.
Patrol Play with a Controller not Having the PATROL Key
1. Select patrol play in the setup menu, and then close the menu. The camera turns to the starting point
and the operations stored in memory are reproduced. Iris operation is valid only in the playback
mode.
2. Open the SET UP menu, or press any manual operation key (e.g., PAN/TILT/ ZOOM/FOCUS) except
the iris keys to stop playback.
Patrol Play with the AUTO PAN Key
1. If the PATROL PLAY function is assigned to the AUTO PAN key, press the AUTO PAN key to turn the
camera back to the starting point and to reproduce the operation data stored in the memory.
2. To stop playback, press the PATROL STOP key and PROGRAM key simultaneously or any manual
operation key (e.g., PAN/TILT/ZOOM/FOCUS) except the iris keys.
Notes:
• During the patrol play mode, the camera movement may occasionally deviate from the entered routine when the routine includes a move to a preset position. If this happens, re-enter the routine of
manual operations for patrol-learn.
• During the patrol play mode, black and white automatic switching does not work.
• During the patrol play mode, when the power of the controller is turned on or off, the patrol play
stops. In this case, press the PATROL PLAY key again. (If SELF RETURN is set to ON, the patrol play
will start again after elapsing the setting return time.)
31
● Alarm Input/Output (ALARM IN/OUT)
Move the cursor to ALARM IN/OUT, and press the CAM (SET) key.
The ALARM IN/OUT submenu appears.
Note: While the camera is in the AF mode or the lens moves between
WIDE and TELE, alarm input may be ignored if several alarm
inputs are received in succession.
ALARM IN 1-4
Alarm input signals are supplied from external devices through
the ALARM IN connector to turn the camera to a preset position.
1. Move the cursor to ALARM IN 1* and select a preset position or
OFF by moving the joystick, then press the CAM (SET) key.
The factory default setting is OFF.
* Set ALARM IN 2, 3 and 4 in the same way as ALARM IN 1.
1 POSI, 2 POSI, 3 POSI and 4 POSI: Preset position. If an alarm
input is received, the camera turns to a preset position, and
sends an alarm output signal. The position number corresponds to the alarm input numbers (1-1, 2-2, 3-3 and 4-4).
B/W: Available for ALARM INPUT 4 only. The camera changes its
mode from colour to black and white if ALARM IN 4 is supplied.
OFF: The camera ignores alarm inputs.
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
ALARM I/O submenu
**
ALARM
ALARM
ALARM
ALARM
ALARM IN/OUT **
IN 1
OFF
IN 2
OFF
IN 3
OFF
IN 4
OFF
CNT-CLS 1
TIME OUT
CNT-CLS 2
COAX ALM OUT
OFF
100MS
OFF
OFF
RET
Note: If two or more alarm inputs are received while the camera is
moving to a preset position, the camera starts to aim at preset
positions in small preset numerical order after current positioning.
CNT-CLS 1, 2 (Output)
Two contact closure signals (Open collector type) are output through the Alarm Output connector.
1. Move the cursor to CNT-CLS 1, and select OFF, ALARM or AUX 1 by moving the joystick to the right
or left.
The factory default setting is OFF.
When ALARM is selected, TIME OUT appears. Select an appropriate duration from among 100 MS,
200 MS, 1000 MS (1 s), 2000 MS (2 s) or 4000 MS (4 s) by moving the joystick to the right or left.
The factory default setting is 100 MS.
Note: The shorter the duration, the more frequent will be the detection output.
2. Move the cursor to CNT-CLS 2, then select OFF, B/W or AUX 2 by moving the joystick to the right or
left.
The factory default setting is OFF.
OFF: Contact closure signals are deactivated.
ALM: Available for CNT-CLS 1 only. A motion detection signal is output.
AUX 1(2): An alarm signal is output when the camera receives a command from the controller.
B/W: Available for CNT-CLS 2 only. ON (active) is output when the camera operates in the black and
white mode if ALARM IN 4 is set to B/W.
Note: It is recommended to set the connected external device to ignore the shorter alarm outputs of
90 ms or less from the camera.
32
COAXIAL ALARM OUT
Alarm output signals are supplied through the coaxial cable.
1. Move the cursor to COAX ALM OUT and select ON or OFF.
2. Press the CAM (SET) key.
The factory default setting is OFF.
ON: The camera sends an alarm output signal after it turns to a preset position.
OFF: The camera does not send the output signal.
Notes:
• The camera ignores alarm inputs during manual operation.
• Select OFF when the camera downloads or uploads the preset data.
● Password Lock (PASSWORD LOCK)
Caution: For security do not operate your VTR for recording while the
password menus are displayed on the monitor screen.
A 3-digit number is used for a password to limit access to the privacy
zone settings.
1. Move the cursor to PASSWORD LOCK, then select ON or OFF by
moving the joystick to the right or left.
The factory default setting is OFF.
Note: ON or OFF can be selected only after going through the
password verification.
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
ON
OFF
ON
OFF
OFF
PASSWORD
OFF: Access to the privacy zone settings is free. ON(ENB) or
OFF(ENB) for PRIVACY ZONE appears on the SPECIAL 1
menu.
ON: Access is limited in the verification menu. ON(DIS) or
OFF(DIS) for PRIVACY ZONE appears on the SPECIAL 1
menu.
2. Press the CAM (SET) key.
Password Verification
3. The password verification menu appears.
3-1 Select a numeral for the first digit by moving the joystick to
the right or left, and press the CAM (SET) key. Though the
entered password is not displayed, the up-arrow moves one
character to the right.
3-2 Repeat the above step for the 2nd and 3rd digits.
Default: 123
3-3 The cursor moves to OK after all the three digits have been
entered. Unless you want to change the password, press the
CAM (SET) key.
If the password entered is entered, the screen returns to SPECIAL 1. ON and OFF settings are the same as made on the
SPECIAL 1 menu is as set in step 1.
If a wrong password is entered, the screen returns to the verification menu. Repeat steps 3-1 to 3-3 to verify the password.
3-4 To cancel an incomplete password,. move the cursor to
RESET, and press the CAM (SET) key. The screen returns to
the verification menu.
33
** PASSWORD? **
0 1 2 3 4 5 6 7 8 9
. . .
↑
OK RESET
NEW PASSWORD
RET
3-5 To return to the SPECIAL 1 menu without verifying the password, move the cursor to RET, and press the CAM (SET) key.
New Password
4. To change the password in step 3-3 above, move the cursor from
OK to NEW PASSWORD, and press the CAM (SET) key. The NEW
PASSWORD menu appears.
Notes:
• The NEW PASSWORD menu is accessible only after the verification has been completed.
• The following operations for NEW PASSWORD will not affect
the ON/OFF setting for PRIVACY ZONE on the SPECIAL 1
menu.
NEW PASSWORD
**
NEW PASSWORD? **
0 1 2 3 4 5 6 7 8 9
. . .
↑
. . .
OK RESET
RET
The up-arrow mark appears indicating the first digit on the first
line.
4-1 Enter a new three-digit password in the same way as in steps
3-1 to 3-2.
4-2 The cursor moves to OK after all three digits have been
entered. Press the CAM (SET) key to move the cursor to the
first digit on the second line.
4-3 Enter the same password as the one you have entered on the
first line.
4-4 The cursor moves to OK. Press the CAM (SET) key. If the new
password is successfully entered, the screen returns to SPECIAL 1.
4-5 Retry steps 4-1 to 4-4. If the first entry for the password is different from the second one, the screen returns to the NEW
PASSWORD? menu.
4-6 To return to the SPECIAL 1 menu without changing the password, move the cursor to RET, and press the CAM (SET) key.
● Cleaning (CLEANING)
With CLEANING in the ON position, the camera’s built-in electromechanical contacts are cleaned at regular intervals (approx. every 7
days).
A dry contract adversely affects picture quality and motors operation.
1. Move the cursor to CLEANING and select ON or OFF by moving
the joystick to the right or left.
The factory default setting is OFF.
ON: The contacts are cleaned for approx. 1 minute. “CLEANING”
disappears when over the cleaning process is completed.
OFF: No contact cleaning.
Note: Select OFF when the camera downloads or uploads the
preset data.
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
ON
ON
OFF
OFF
CLEANING
CLEANING
34
● Electronic Zoom (EL-ZOOM)
The electronic zoom magnifies a scene 10-fold. With a 22-fold optical
zoom lens, the camera is capable of 220-fold zoom.
1. Move the cursor to EL-ZOOM and select ON or OFF by moving
the joystick to the right or left, and then press the CAM (SET) key.
The factory default setting is ON.
ON: 10 - fold electronic zoom is available with the ZOOM switch
on the controller.
OFF: The electronic zoom function is not used.
Notes:
• A scene magnified by the electronic zoom function may be
inferior in picture quality to a non-magnified one.
• The electronic zoom does not function in the preset position
setting mode.
• To set preset positions directly from the WV-CU550B, WVCU360 or WV-CU161 System Controller, you need to set the
electronic zoom function temporarily to OFF.
● Preset Alarm (PRESET ALM)
An alarm output is sent when the camera moves to the designated
position depending on the mode.
1. Move the cursor to PRESET ALARM and select ON or OFF.
The factory default setting is OFF.
ON: Alarm signals are output in the following cases.
• When a preset positioning sequence is completed while
AUTO MODE is set to SEQ.
• When a preset positioning sequence is completed while
AUTO MODE is set to SORT.
• When positioning to the starting point is completed while
AUTO MODE is set to AUTO PAN.
• When the self-return function has returned the camera to its
home position.
• When preset positioning is completed by manual operation.
• When positioning to the starting point is completed while
PATROL is set to PLAY.
OFF: Alarm signals are not output.
Note: Select OFF when the camera downloads or uploads the
preset data.
● Image Hold (IMAGE HOLD)
The camera picture remains as a still image on the monitor screen
until the camera reaches the preset position. This function is useful for
surveillance via local area network.
1. Move the cursor to IMAGE HOLD and select ON or OFF.
The factory default setting is OFF.
35
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
OFF
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
ON
OFF
Special 1 menu
** SPECIAL
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
ALARM IN/OUT
PASSWORD LOCK
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
RET
1 **
OFF(ENB)
ON
ON(USER)
STOP
OFF
OFF
ON
OFF
ON
ON: The last displayed still image is shown till the camera finishes
moving to a preset position. However, the still image may be
distorted with the effect of panning or tilting.
OFF: The current image is being displayed while the camera is
moving to a preset position.
■ Camera Setting
To Display the Camera Setting Menu
• Move the cursor to CAMERA O, and press the CAM (SET) key.
The camera setting menu appears.
Setup menu
** SET UP MENU **
PRESET 1
MAP
HOME POSITION OFF
OFF
SELF RETURN
OFF
AUTO MODE
AUTO PAN KEY AUTO PAN
DIGITAL FLIP ON
LOCAL/REMOTE LOCAL
SPECIAL1
CAMERA
RS485 SET UP
Camera setting menu
● Camera Identification (CAMERA ID)
1. Move the cursor to CAMERA ID, and select ON to display the
camera identification by using the joystick.
The factory default setting is OFF.
2. Follow the steps below to edit the camera ID characters:
2-1 Move the cursor to CAMERA ID and press the CAM (SET) key
to display the character editing menu.
2-2 Move the cursor to the character you want to edit or change
by using the joystick, and press the CAM (SET) key. The
selected character appears in the editing area.
2-3 Repeat the steps above until all characters are edited.
3. After editing the camera identification characters, follow the steps
below to decide the position of the CAMERA ID.
3-1 Move the cursor to POSI, and press the CAM (SET) key to
display the ID position menu.
3-2 Decide the position of the camera ID by using the joystick.
Press the MON (ESC) key to fix the position, and return to the
character editing menu.
Notes:
• When you want the pointer to move to a specific character in
the editing area, select a new character, and press the CAM
(SET) key. This function allows you to edit or correct a specific character.
• To enter a blank space into the camera ID, move the cursor to
SPACE, and press the CAM (SET) key.
• To erase all characters in the editing area, move the cursor to
RESET, and press the CAM (SET) key.
36
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
** SET UP **
CAMERA ID
ON
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
Character editing menu
CAMERA ID.––
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
–––– POSI RET RESET
CAM1............
CAM1
• The CAMERA ID moves faster when the joystick is kept at the
right or left for one second or more.
• Move the cursor to RET to return to the SET UP menu, and
press the CAM (SET) key.
CAMERA ID.––
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
–––– POSI RET RESET
CAM1............
CAMERA ID.––
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
–––– POSI RET RESET
CAM1............
● Light Control Setting (ALC/MANUAL)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to ALC/MANUAL and select ALC or MANUAL by
using the joystick.
The factory default setting is ALC.
When you select ALC, set backlight compensation.
Note: The backlight compensation submenu associated with this
menu is described separately and should be set up after
installing the camera at the site and observing the actual site
picture.
3. When MANUAL is selected, quit the setup menu by pressing the
MON (ESC) key. Press the OPEN or CLOSE key on the controller
for iris adjustment.
(1) ALC Mode with BLC ON
1. Press the CAM (SET) key after selecting ALC. The ALC CONT
menu appears.
2. Move the cursor to the BLC and select ON.
3. If you want to adjust the video output level, move the “I” cursor for
LEVEL. Adjust it to the desired level by using the joystick.
4. Move the cursor to RET and press the CAM (SET) key to return to
the CAM SET UP menu. To return to the camera picture, press the
F4 button.
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
Backlight compensation menu
** ALC CONT **
BACK LIGHT COMP
BLC
OFF
MASK SET
LEVEL
••••|••••
+
RET
** ALC CONT **
BACK LIGHT COMP
BLC
ON
LEVEL
••••|••••
+
RET
37
(2) ALC Mode with BLC OFF
1. Move the cursor to BLC and select OFF. (When you select MANUAL, BLC is not available.) The MASK SET appears on the menu.
2. Move the cursor to MASK SET and press the CAM (SET) key. The
48 mask areas appear on the monitor screen. The cursor is blinking in the top left corner of the screen.
3. To mask an area where backlight is bright, move the cursor to the
area and press the CAM (SET) key. The mask turns white. Repeat
this procedure to mask the desired area.
4. To cancel a masked area, move the cursor to the area, and press
the CAM (SET) key. To cancel all masking areas, press the F2
button of the WV-CU550B.
For the WV-RM70, press the right and left switches simultaneously.
Blinking
Blinking
Turns to white
Blinking
5. After masking is completed, press the MON (ESC) key. The 48
mask areas on the monitor screen disappear and the ALC CONT
menu appears.
6. If you want to change the picture contrast, move the “I” cursor for
LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM (SET) key to return to
the CAM SET UP menu.
To return to the camera picture, press the F4 button.
** ALC CONT **
BACK LIGHT COMP
BLC
OFF
MASK SET
LEVEL
••••|••••
+
RET
** ALC CONT **
BACK LIGHT COMP
BLC
OFF
MASK SET
LEVEL
RET
38
••••|••••
+
● Shutter Speed Setting (SHUTTER)
Camera setting menu
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to SHUTTER and select the electronic shutter
speed by using the joystick. The factory default setting is OFF.
The electronic shutter speed changes as follows by using the joystick:
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
OFF (1/50)
1/10 000
1/120
1/4 000
1/250
1/2 000
SPECIAL2
1/500
1/1 000
● Gain Control (AGC)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to AGC and select ON (LOW), ON (MID), ON
(HIGH) or (OFF) by using the joystick.
The factory default setting is ON (MID).
ON (LOW): Selects lower auto gain control.
ON (MID): Selects normal auto gain control.
ON (HIGH): Selects higher auto gain control.
OFF (Fixed Level): Disables the gain control function.
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
Notes:
• Even if AGC is set to ON and if the noise reduction function is
enabled, afterimages may be produced by shooting a moving
object or by panning or tilting the camera.
• For more information, refer to Digital Noise Reduction on page 46.
● Electronic Sensitivity Enhancement (SENS UP)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to SENS UP and select the desired electronic
sensitivity enhancement mode by using the joystick.
The factory default setting is X2 AUTO.
The electronic sensitivity enhancement mode changes as follows
by operating the joystick:
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
OFF
X2 AUTO
X16 AUTO
X6 FIX
X4 AUTO
X32 AUTO
X10 FIX
OFF
X16 FIX
X6 AUTO
X2 FIX
X10 AUTO
X4 FIX
X32 FIX
Note: While the SENS UP function is selected, noise or spots may
appear in the picture when the sensitivity of the camera is
increased. This is a normal phenomenon.
39
SPECIAL2
● Synchronization (SYNC)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to SYNC and select LL or INT by using the joystick.
The factory default setting is INT.
Important Notices:
1. The priority of SYNC modes is as follows:
1. Multiplexed vertical drive (VD2) (highest priority)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. To use internal sync, select INT.
3. Whenever the vertical drive pulse (VD2) is supplied to the camera, the camera sync mode is automatically switched to the multiplexed vertical drive pulse (VD2) regardless of the selected sync
mode.
Line-lock Sync Mode (LL)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to SYNC and select LL by using the joystick. LL
sync mode is not available when the multiplexed vertical drive
(VD2) pulse is supplied.
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
LL
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
3. After selecting LL, press the CAM (SET) key.
The SYNC menu appears on the monitor screen.
SYNC menu
4. Supply the video output signal of the camera to be adjusted and
the reference video output signal (for example, Camera 1) to a
dual-trace oscilloscope.
** SYNC **
V PHASE
COARSE
1(1--16)
FINE
•|•••••••
+
5. Set the dual-trace oscilloscope to the vertical rate and expand the
vertical sync portion on the oscilloscope.
RET
6. Move the cursor to COARSE by using the joystick.
7. Match the vertical phases for both video output signals as closely
as possible by using the joystick. The coarse adjustment can be
incremented in steps of 22.5 degrees (16 steps) with the joystick.
1 (1 - - - 16): 0 degrees
2 (1 - - - 16): 22.5 degrees
16 (1 - - - 16): 337.5 degrees
Note: After the 16th step, the adjustment returns to the first step.
40
** SYNC **
V PHASE
COARSE
1(1--16)
FINE
•|•••••••
+
RET
8. Move the cursor to FINE by using the joystick.
9. Match the vertical phase for both video output signals as closely
as possible by using the joystick.
** SYNC **
V PHASE
Notes:
• When the “|” cursor reaches the “+” end, it jumps back to “–”.
At the same time, COARSE is incremented by one step to
enable a continuous adjustment. The reverse takes place
when the “|” cursor reaches the “–” end.
• When the joystick is kept at the right or left for one second or
more, the “|” cursor moves quickly.
• To reset COARSE and FINE to the preset values, press the F2
button of the WV-CU550B. For the WV-RM70, press the Right
and Left switches simultaneously. COARSE is preset to zerocrossing of the AC line phase.
• If the AC line phase contains spike noise, etc., the vertical
phase of the video output signal may be disturbed.
COARSE
4(1--16)
FINE
••••••|••
+
RET
** SYNC **
V PHASE
COARSE
1(1--16)
FINE
•|•••••••
+
RET
● White Balance (WHITE BAL)
(1) Auto-Tracing White Balance Mode (ATW1/ATW2)
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to WHITE BAL and select ATW1 by using the joystick.
The factory default setting is ATW1.
The white balance of the camera is automatically adjusted.
3. For fine adjustment of ATW1/ATW2, press the CAM (SET) key. The
ATW1/ATW2 fine adjustment menu appears on the monitor
screen.
4. Move the cursor to R.
Obtain the optimum red gain by moving the joystick to the right or
left.
5. Move the cursor to B.
Obtain the optimum blue gain by moving the joystick to the right
or left.
6. Move the cursor to RET by using the joystick and press the CAM
(SET) key to return to the SET UP menu.
41
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
ATW fine adjustment menu
**
R
B
RET
ATW1
**
••••|••••
+
••••|••••
+
Camera setting menu
(2) Automatic White Balance Control Mode (AWC)
1. Display SET UP MENU on the monitor screen by referring to page
16.
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
AWC→PUSH SW
OFF
MOTION DET
MANUAL S
AF MODE
2. Move the cursor to WHITE BAL and select AWC → PUSH SW by
using the joystick.
3. Press the CAM (SET) key to start the white balance setup. PUSH
SW is highlighted to indicate that white balance is being set.
RET
SPECIAL2
AWC fine adjustment menu
4. PUSH SW returns to normal when balance setting is completed.
**
5. For fine adjustment of the AWC, move the cursor to AWC and
press the CAM (SET) key. The AWC fine adjustment menu
appears on the monitor screen.
8. Move the cursor to RET by using the joystick and
press the CAM (SET) key to return to the SET UP
menu.
**
••••|••••
+
••••|••••
+
B
6. Move the cursor to R.
Obtain the optimum red gain by moving the joystick to the right or
left.
7. Move the cursor to B.
Obtain the optimum blue gain by moving the joystick to the right or left.
AWC
R
RET
Bluish
10000 K
Blue sky
9000 K
Rainy
8000 K
AWC
Cloudy
7000 K
Partly cloudy
ATW
6000 K
Fine
Fluorescent
lamp
5000 K
4000 K
Halogen lamp
Tungsten
lamp
3000 K
2000 K
1000 K
Reddish
42
Candle
● Motion Detector (MOTION DET)
Camera setting menu
1. Display SET UP MENU on the monitor screen by referring to page
16.
2. Move the cursor to MOTION DET and select ON or OFF by using
the joystick.
The factory default setting is OFF.
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
ON
AF MODE
MANUAL S
RET
3. If ON is selected, press the CAM (SET) key.
The MOTION DETECT menu appears.
You can mask the areas in this menu.
SPECIAL2
Motion detect menu
** MOTION DETECT **
LEVEL
4. Move the cursor to MASK SET and press the CAM (SET) key.
48 mask areas appear on the monitor screen.
Refer to the Light Control Setting on page 37 for masking operations.
DISPLAY MODE
ALARM
6. Move the cursor to ALARM and select ON or OFF by using the
joystick.
The factory default setting is OFF.
ON: The alarm signal is supplied while the display mode is activated.
OFF: The alarm signal is not supplied while the display mode is
activated.
7. Move the cursor to DISPLAY MODE.
Press the CAM (SET) key to see the present setting. The areas
that detect the motions blink.
8. Move the cursor to LEVEL by using the joystick.
Obtain the optimum detection level by moving the joystick to the
right or left.
Note: Repeat the above procedures until you obtain the adjusted
results.
9. Move the cursor to RECOVER TIME by using the joystick.
The factory default setting is 1 MIN.
You can select the following recover times.
OFF
60MIN
1MIN
2MIN
30MIN
3MIN
20MIN
5MIN
10MIN
10. Move the cursor to RET and press the CAM (SET) key to return to
SET UP.
43
OFF
MASK SET
RECOVER TIME
RET
5. After masking areas, press the MON (ESC) key. The MOTION
DETECT menu appears on the monitor screen.
••••|••••
+
1MIN
Important Notices:
• The motion detection should meet the following conditions.
1) The picture size on the screen should be larger than 1/48 of the actual picture size.
2) The contrast ratio between the object and the background picture should be more than 5 % at
the maximum detection level.
3) The time it takes the object to move from one end of the screen to the other should be more than
0.1 seconds.
• Also under the following conditions, mask or adjust the detection level to prevent malfunction.
1) When leaves, or curtains, etc., are swayed by the wind.
2) When a picture has a high noise content due to low light conditions.
3) When the object is illuminated by lighting equipment that constantly turns on and off.
• The alarm signal will take approx. 0.2 seconds to reach the alarm terminal of the VTR, after the camera detects the object.
Because the alarm signal is multiplexed on the video signal it may be mistakenly interpreted by other
video equipment as a time code signal. Therefore, when this camera is not used in a Panasonic
Intelligent CCTV System, select OFF to prevent the above from occurring.
• The motion detection function is not designed specifically for prevention of theft, fire, etc.
● Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the following mode by
moving the joystick to the right or left.
The factory default setting is MANUAL S.
S, M and L stand for Small, Middle and Large areas respectively
in the centre of a scene that are used for sensing sharpness in
auto-focusing.
AUTO S
MANUAL L
AUTO M
AUTO L
MANUAL M
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
MANUAL S
MANUAL S, M, L: Auto focus is activated only when the AF key
on the controller is pressed.
AUTO S, M, L: Auto focus is activated automatically while the
pan, tilt or zoom operation is manually performed. These may
be selected in the same way as MANUAL by pressing the AF
key on the controller.
2. To confirm auto-focus operation, press CAM (SET) key.
Notes:
• When the electronic sensitivity enhancement (SENS UP) is activated except in the x2 FIX or x2 AUTO
mode, this function is automatically set to MANUAL (S, M, L).
• The auto focus lens does not function properly in the AUTO mode after using the WIDE lens.
• The auto focus lens may not function properly in the AUTO mode under the following conditions.
1. Dirt or water on window glass.
The auto focus may focus on the dirt or water.
2. Low lighting or illumination.
3. Bright objects or high intensity objects.
4. Single colour object such as a white wall or fine felt
5. No centre objects and sloping objects
6. Far and near objects on the screen
44
● Special 2 Menu (SPECIAL2)
This menu lets you adjust and set up the picture quality to meet your
requirements.
• Display SET UP on the monitor screen by referring to page 16.
• Move the cursor to SPECIAL2 and press the F2 button of the WVCU550B. The special menu appears on the monitor screen.
For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.
(1) Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN. The “I” cursor is highlighted.
2. While observing the vectorscope or colour video monitor, adjust
the chroma level by moving the joystick to the right or left.
To reset the level to the factory default setting, press the F2 button
of the WV-CU550B.
For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.
Camera setting menu
** SET UP **
CAMERA ID
OFF
ALC/MANUAL
ALC
SHUTTER
OFF
AGC
ON(MID)
SENS UP
X2 AUTO
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
AF MODE
MANUAL S
RET
SPECIAL2
Special 2 menu
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
PEDESTAL
•|•••••••
+
OFF
BW
ON
BURST(BW)
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
(2) Aperture Level Setting (AP GAIN)
1. Move the cursor to AP GAIN. The “I” cursor is highlighted.
2. While observing the video monitor, adjust the aperture level by
moving the joystick to the right (sharp) or left (soft).
To reset the level to the factory default setting, press the F2 button
of the WV-CU550B.
For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.
(3) Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL. The “I” cursor is highlighted.
2. While observing the waveform monitor/oscilloscope or video monitor, adjust the pedestal level (black level) by moving the joystick
to the right (high, bright) or left (low, dark).
To reset the level to the factory default setting, press the F2 button
of the WV-CU550B.
For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.
(4) Black and White Setting (BW)
1. Move the cursor to BW and select AUTO, ON or OFF by moving
the joystick to the right or left. Factory default setting: OFF.
AUTO: The camera selects the black and white mode if the picture is dark, or the colour mode if the picture is bright enough.
ON: The black and white mode is selected.
OFF: The color mode is selected.
Note: Selecting the colour mode is disabled if ALARM IN 4 is
set to B/W on the Special 1 menu.
45
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
PEDESTAL
•|•••••••
+
BW
OFF
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
•|•••••••
PEDESTAL
+
BW
OFF
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
•|•••••••
PEDESTAL
+
BW
AUTO
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
2. If you have selected AUTO, press the CAM (SET) key to open the
BW AUTO submenu.
3. Select HIGH or LOW for the threshold level at which the camera
automatically switches to BW or colour mode. Default: HIGH
The illuminance shown below is based on the assumption that the
camera is used in an area lit by halogen lamps, and that AGC on
the menu is set to MID.
HIGH: approximately 6 lux
LOW: approximately 2.5 lux
Note: When near-infrared lamps are used, the image may be
displayed out of focus and mode switching may not perform automatically.
4. Move the I cursor to set DURATION TIME. Default: 30 seconds
The camera determines whether to switch the mode when the
time set for holding a picture motionless on the screen has
elapsed.
Available duration times: (S) 10 s ↔ 30 s ↔ 60 s ↔ 300 s (L)
Note: A pan/tilt, zoom or focus operation will restart the holding time.
(5) Black Burst Setting [BURST (BW)]
Move the cursor to BURST (BW) and select ON or OFF by moving
the joystick to the right or left. Default: ON.
ON: The burst signal is supplied along with the black and white
composite video.
OFF: The burst signal is not output.
Note: It is recommended to select ON usually.
(6) To Restore the Camera Default Position (REFRESH)
Move the cursor to REFRESH by using the joystick and press the
F2 button of the WV-CU550B.
For the WV-RM70, WV-CU360 or WV-CU161, keep pressing the
Right and Left switches simultaneously for 2 seconds or more.
** BW AUTO **
HIGH
LEVEL
DURATION TIME •|••
S L
RET END
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
PEDESTAL
•|•••••••
+
BW
OFF
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
** SPECIAL2 **
••••|••••
CHROMA GAIN
••••|••••
AP GAIN
PEDESTAL
•|•••••••
+
OFF
BW
ON
BURST(BW)
→PUSH SW
REFRESH
CAMERA RESET →PUSH SW
DNR
LOW1
RET
(7) Camera Resetting (CAMERA RESET)
Move the cursor to CAMERA RESET by using the joystick and
press the F3 button of the WV-CU550B.
The camera is reset to the factory default settings.
For the WV-RM70, keep pressing the Right, Left and Set switches
simultaneously for 2 seconds or more. For the WV-CU360 or WVCU161, keep pressing the Right and Left switches and the numeric button 5 simultaneously for 2 seconds or more.
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
PEDESTAL
•|•••••••
+
BW
OFF
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
46
(8) Digital Noise Reduction (DNR)
DNR may be used to improve quality under low light conditions. There are 4 levels of DNR, which may be selected
depending on local site conditions. Factory default setting:
LOW1
You may need to try different settings to find the most suitable
conditions for your application.
Move the cursor to DNR and select LOW1, LOW2, HIGH1 or
HIGH2 by moving the joystick to the right or left.
LOW1: DNR level is low. The after-image remains.
LOW2: DNR level is low. The after-image is reduced.
HIGH1: DNR level is high. The after-image remains.
HIGH2: DNR level is high. The after-image is reduced.
(9) To Close the SPECIAL2 Menu
Move the cursor to RET and press the CAM (SET) key.
The setup menu appears on the monitor screen.
** SPECIAL2 **
CHROMA GAIN
••••|••••
••••|••••
AP GAIN
•|•••••••
PEDESTAL
+
BW
OFF
ON
BURST(BW)
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
** SPECIAL2 **
CHROMA GAIN
••••|••••
AP GAIN
••••|••••
PEDESTAL
•|•••••••
+
BW
OFF
BURST(BW)
ON
REFRESH
→PUSH SW
CAMERA RESET →PUSH SW
DNR
LOW1
RET
Reset to the Factory Default Settings
Any of the above settings plus the ALC/MANUAL level control and
phase adjustments can be reset to the factory default settings by
placing the cursor over the desired mode and then pressing the
F2 button of the WV-CU550B.
For the WV-RM70, keep pressing the Right and Left switches
simultaneously for 2 seconds or more.
■ RS485 Setup
● Initial Camera Communication Parameters
In an RS485 chain, the matrix switcher, PC, controllers and cameras should be set to the same protocol and parameters for communication. Confirm the system protocol and parameters prior to
setting the communication parameters for the camera.
The initial communication parameters for WV-CW860 and WVCW864E are shown on the RS485 setup menu below. Other than
the on-screen setup parameters, the 4-bit DIP switch may be used
to select 2-line (Half Duplex) or 4-line (Full Duplex) communication.
● Changing the Camera Communication
Parameters
You can remotely control this camera by using a specified extension unit such as a computer with a modem.
1. Display the SET UP MENU. Move the cursor to RS485 SET UP
and press the CAM (SET) key. The RS485 SET UP menu
appears on the monitor.
2. Move the cursor to the item and select the parameter by moving the joystick to the right or left.
47
RS485 Setup menu
** RS485 SET
UNIT NUMBER
SUB ADDRESS
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
UP **
1
----19200
8
NONE
1
NOT USE
OFF
AUTO2
---
Unit Number (UNIT NUMBER)
Displays the unit number set by the DIP switch. If the switch is set to
1-96, select a number by moving the joystick to the right or left. In an
RS485 chain each unit must have a unique number.
Factory default setting: 1. See INSTALLATION for DIP switch setting.
Sub Address (SUB ADDRESS)
Do not set.
RS485 Setup menu
** RS485 SET
UNIT NUMBER
SUB ADDRESS
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
UP **
1
----19200
8
NONE
1
NOT USE
OFF
AUTO2
---
Baud Rate (BAUD RATE)
Specifies the transmission speed (2 400, 4 800, 9 600, 19 200 bit per second) for the RS485 communication. The factory default setting is 19 200.
Data Bit (DATA BIT)
Specifies the number of data bits (7 or 8 bits) for the RS485 communication. The factory default setting is
8.
Parity Check (PARITY CHECK)
Specifies the parity check mode (NONE, ODD, EVEN). The factory default setting is NONE.
Stop Bit (STOP BIT)
Specifies the number of stop bits (1 or 2 bits). The factory default setting is 1.
X ON/X OFF (X ON/X OFF)
Specifies whether to apply flow control or not (USE or NOT USE). The factory default setting is NOT USE.
Wait Time (WAIT TIME)
Specifies the time to wait until retrying after confirming that no data is received from the controller.
(OFF: no retry, 100, 200, 400, 1 000 ms).
The factory default setting is OFF.
Alarm Data (ALARM DATA)
Specifies the alarm transmission mode depending on the protocol selected by the 8-bit DIP switch.
POLLING: Transmits the alarm data in response to requests from the controller.
AUTO 1: Transmits the alarm data each time an alarm signal is received by the camera.
AUTO 2 (Default): Transmits alarm data at intervals of 5 seconds.
Delay Time (DELAY TIME)
Specifies the time to transmit the acknowledge request when communicating on a 2-line connection.
[----, 100 ms] Factory default setting: ---- (no set).
This menu appears only when a 2-line communication is used. Make sure to be 100 ms when connecting
the camera with the WJ-FS616 Video Multiplexer or Matrix Switcher WJ-SX350 in a 2-line communication
system.
The settings become effective with the closing of SET UP MENU.
Note: Set the same parameters for the cameras, controllers and personal computers in an RS485 chain.
48
INSTALLATION
Precautions
• The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes.
• Be sure to switch the camera off before installation and connection.
• Do not install the camera near the air outlet of an air conditioner.
■ Mounting the Camera
Ceiling mount
The figure shows an example of the camera mounted on a
ceiling with a locally procured bracket.
Refer to the instructions included with the bracket for filling
gaps and holes with waterproof material.
Wall mount
The figure shows an example of the camera mounted on a
wall with the optional WV-Q110E Wall Mount Bracket. See
instructions included with the optional bracket.
Sun Shield
Use the optional WV-7176E Sun Shield to protect the camera from direct sunlight. See instructions included with the
sun shield.
49
1. Preparations
3. Mounting the Bracket
(1) Procure a ceiling mount bracket.
(2) Installation Surface
CAUTION: Consult an expert on the
load bearing capacity of the installation surface and structure. If the surface is not strong enough, the camera may fall down. Refer to the product specifications for weights.
Prepare appropriate hardware (e.g. wall
nuts, anchor bolts, etc.) for fixing on the
installation surface.
(1) Fix the bracket to the installation surface
using appropriate bolts, nuts or the like
(not supplied).
Attachment Pipe
2. Disassembling the Camera
(1) Remove the upper base from the camera by loosening 3 screws. Turn the
upper base and separate it.
x3
(2) Fix the attachment pipe to the bracket.
(3) Thread cables through the bracket.
Connect cables, referring to CONNECTIONS.
Cables
Upper Base
(2) Remove the attachment pipe from the
upper base by loosening 4 screws.
(4) Fix the upper base to the attachment pipe
using 4 screws, and fill the gap between the
bracket and attachment pipe with waterproof
material such as silicon clay. See instructions of the bracket for details.
Waterproof Material
x4 Screws
x4
Upper Base
50
4. Setting the Switches
The 8-bit DIP switch has two functions. It is
used to restore the factory default settings
and to specify the unit number. Before setting, peel off the seal covering the switch
holes. After setting the switch, replace the
seal. The 4-bit DIP switch selects termination ON/OFF and half/full duplex for RS485
communication. The switch settings are
read into the camera when the power is
turned on. After changing the switch settings, be sure to turn the power off, then turn
it back on again. Switch positions and functions are shown below.
Camera top view
REAR
S TA R
AC24
T
VO
1
SW
NLY
RS4
85Se
tting
2
SW
Seal
ON
RS485 Parameter Setup
The selected protocol, communication parameters, and set unit numbers are read into
the camera when the power is switched on.
1
3
SW
2
1
4
8-b
5
it D
7
IP
6
2
SW
8
SW
ON
(1) Switch off the camera.
1
3
2
4
IP
SW
it D
b
4-
(2) Set the switch as shown in the table
below.
(3) Set the unit number with the DIP switch
(see the next page).
Switch view
Switch position
Returns to the factory default settings.
ON
(4) Switch on the camera to read in the
changed switch settings.
Note: The changed communication
parameters are displayed on the
RS485 SETUP menu after the camera has been switched on.
1
3
4
5
6
7
8
Switch position
Baud rate
Parameter selection
Parity
Data bit
check
Stop
bit
ON
1 2
ON
3
4
5
6
7
8
1 2
ON
3
4
5
6
7
8
3
4
5
6
7
8
1
51
2
2
19 200
8
None
1
9 600
8
None
1
4 800
8
None
1
Unit Number
Switch 1, an 8-bit DIP switch, specifies the unit number or
restores the factory default settings when using the Panasonic
protocol.
When the switch position corresponding to the unit number 196* is selected, setting should be made on the RS485 SET UP
menu (see page 47).
SW1
ON
1
2
3
4
5
6
7
8
8-bit DIP SW
For Panasonic’s Protocol
Switch position
Unit
number
2
3
4
5
6
7
8
1-96*
ON
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
2
3
4
5
6
7
8
3
2
3
4
5
6
7
8
4
2
3
4
5
6
7
8
5
2
3
4
5
6
7
8
6
2
3
4
5
6
7
8
7
2
3
4
5
6
7
8
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
11
2
3
4
5
6
7
8
2
3
4
5
6
7
8
12
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
14
1
2
3
4
5
6
7
8
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
3
4
5
6
7
8
47
1
2
3
4
5
6
7
8
48
1
2
3
4
5
6
7
8
49
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
31
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
32
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
53
54
55
1
56
34
1
57
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
35
1
58
ON
36
1
59
ON
2
3
4
5
6
7
8
37
60
1
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
61
1
ON
62
1
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
63
1
ON
64
1
ON
65
1
ON
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
66
1
44
ON
1
52
ON
ON
1
51
ON
33
43
1
50
ON
42
1
22
2
41
1
21
ON
1
30
ON
3
1
ON
20
1
29
ON
2
46
ON
19
1
28
ON
ON
8
40
1
ON
7
ON
18
1
27
ON
3
6
39
1
ON
1
26
ON
2
5
ON
17
1
4
ON
16
ON
3
38
1
ON
2
ON
15
1
25
ON
2
1
ON
ON
ON
1
24
ON
13
ON
1
3
ON
ON
1
2
ON
ON
1
1
Unit
number
ON
ON
10
ON
1
23
ON
ON
1
8
ON
ON
1
7
ON
ON
1
6
ON
ON
1
5
ON
ON
1
4
ON
ON
1
3
ON
ON
1
1
Switch position
ON
2
ON
ON
1
1
ON
ON
1
Unit
number
ON
ON
1
Switch position
ON
1
45
67
ON
1
68
(to be continued)
52
Switch position
Unit
number
2
3
4
5
6
7
8
69
ON
1
2
3
4
5
6
7
8
70
2
3
4
5
6
7
8
71
2
3
4
5
6
7
8
72
2
3
4
5
6
7
8
73
2
3
4
5
6
7
8
74
2
3
4
5
6
7
8
75
53
7
8
1
1
1
1
1
1
2
3
4
5
6
7
8
76
1
2
3
4
5
6
7
8
79
3
4
5
6
7
8
77
1
1
2
3
4
5
6
7
8
87
1
2
3
4
5
6
7
8
88
2
3
4
5
6
7
8
89
2
3
4
5
6
7
8
90
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
2
3
4
5
6
7
8
80
1
ON
2
3
4
5
6
7
8
81
1
ON
2
3
4
5
6
7
8
82
1
91
ON
2
3
4
5
6
7
8
83
1
92
ON
2
3
4
5
6
7
8
84
1
93
ON
2
3
4
5
6
7
8
85
1
94
ON
ON
2
Unit
number
ON
ON
ON
1
6
ON
ON
1
5
ON
ON
1
4
ON
ON
1
3
ON
ON
1
2
ON
ON
1
1
Switch position
ON
78
ON
ON
1
Unit
number
ON
ON
1
Switch position
2
3
4
5
6
7
8
86
1
95
RS485 Setting
The 4-bit DIP switch is used for
RS485 termination.
(2) Be sure to hook the fall prevention wire
into the bracket.
SW2
ON
1
2
3
4
4-bit DIP SW
BP 1
Switch
position
Function
ON
Termination ON
OFF
Termination OFF *
BP 2 BP 3 BP 4
Function
Fall Prevention
Wire
Switch ON ON ON Half duplex (2 line)
position OFF OFF OFF Full duplex (4 line) *
Notes:
• Defaults are marked with *.
• BP stands for Bit Position.
• Full duplex is not available in a daisy chain
connection. (Panasonic system controllers
only)
(3) Fix the camera to the upper base.
• Move the camera up so that its
guide pins fit into the guide holes of
the upper base.
• Turn the camera counter-clockwise
to the end, viewed from the bottom.
• Fasten 3 screws.
5. Mounting the camera
(1) Aim the “START” arrow at the bent portion of the leaf spring.
Bending
S TA R
Leaf Spring
T
x3 Screws
Upper Base
Enclosure
54
CONNECTIONS
Precautions
• The following connections should be made by qualified service personnel or system installers in
accordance with all local codes.
• See the reverse side of the cover page for mains lead connection.
220 V - 240 V AC (WV-CW860)
24 V AC cable
24 V AC (WV-CW864E)
Data port
RS485 cable
Coaxial cable
Video output
Alarm in
BNC plug
To VIDEO IN
(CAMERA IN)
BNC plug
To sensors
To indicators
Alarm out
✻ The coaxial cable length (RG-6/U, 5C-2V) for the connection is up to
1 200 meters (4 000 ft.)
Note: When powered up, the unit performs a self-check (including one panning, tilting, zooming and
focusing operation).
• 24 V AC Power Supply Connection
Recommended wire gauge sizes for 24 V AC line
Copper wire size
(AWG)
Length
of cable
(approx.)
#20
#18
#24
#22
(0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
(m)
20
30
45
75
(ft)
65
100
160
260
Accessory Connector Information
Pin no.
Up
Up
Power source
1
24 V AC LIVE
2
24 V AC NEUTRAL
4
3
3
Ground
2
1
4
Not use
How to Assemble the Cable with the
Accessory Connector
Strip back the cable jacket approx. 3 mm (0.1
inch) and separate the individual conductors.
Approx.
Approx.
33 mm
(0.1 inch)
inch)
mm (0.1
Wire
Wire
Up A
Up
Contact
Contact
Insert
Insert
wire until
untilAAposition
position
Insert the wire
and
contacts.
and clamp
clamp the contacts.
55
Prepare the individual conductors for clamping.
Use MOLEX band tool part number 57027-5000
(for UL-Style Cable UL1015) or 57026-5000 (for
UL-Style UL1007) for clamping the contacts.
After clamping the contacts, push them into the
proper holes in the accessory connector of this
camera until they snap in place.
Wire
Wire
Contact
Contact
CAUTIONS
• Shrinking the cable-entry seal is a onetime procedure. Do not shrink the cableentry seal until it has been ascertained
that the unit is functioning.
• CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY.
• RS485 Connection
Brown
GND
Red
Data transmission
T (B)
Orange
T (A)
Yellow
Data reception
R (B)
Green
R (A)
Note:
Use the cable that is described below for RS485 site communication.
• Shielded, twisted pair cable
• Low impedance
• Wire gauge size is thicker than AWG #22 (0.33 mm2).
• ALARM IN Connections
An 8-pin and a 4-pin harness are supplied with the camera as standard accessories. Connect external sensors to this connector. Input specifications are low-active, non-voltage contact (ON when
active) or open collector (Low when active). The table below shows wire colours versus pin functions.
Alarm IN (8-pin)
Wire colour
Function
Black
IN 1
Brown
GND
Red
IN 2
Orange
GND
Yellow
IN 3
Light blue or green
GND
Blue
IN 4
Purple
GND
• ALARM OUT Connections
Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications
are low-active, open-collector and a drive capacity of 16 V DC 100 mA maximum. The table below
shows wire colours versus pin functions.
Alarm OUT (4-pin)
Wire colour
Function
Grey
OUT 1
White
GND
Pink
OUT 2
Yellow green or light blue
GND
Note: Use a relay if the voltage or current of the connected device exceeds the ratings.
56
SYSTEM CONNECTIONS
Colour CCTV cameras
Max. 64 cameras
Matrix
switcher
Personal computer
RS-232C port
VTRs (up to 16)
Alarm inputs
Printer
System status
monitor
Monitors (up to 16)
ALARM
BUSY
ALARM
F1
ACK
RESET
BACK FORWARD
SEQ SEQ ALT
1
F2
2
F3
3
F4
PRESET
5
ALARM
F1
UP
IRIS
CLOSE OPEN
ACK
RESET
LEFT
4
BUSY
BACK FORWARD
SEQ SEQ ALT
1
F2
2
F3
3
2
DEC INC
–1CAM +1CAM STOP
7
8
9
MON
0
CAM
ESC
SET
F4
PRESET
5
F1
ACK
RESET
LEFT
4
ALARM
UP
IRIS
CLOSE OPEN
RIGHT
6
BACK FORWARD
SEQ SEQ ALT
1
F2
2
F3
3
FOCUS
NEAR
WIDE
FAR
AUX
DOWN
System Controller WV-CU
1
550B
2
DEC INC
–1CAM +1CAM STOP
7
8
9
MON
0
CAM
ESC
SET
F4
5
BUSY
F1
UP
IRIS
CLOSE OPEN
ACK
RESET
LEFT
4
BACK FORWARD
SEQ SEQ ALT
1
F2
2
F3
3
FOCUS
NEAR
WIDE
FAR
AUX
DOWN
System Controller WV-CU
1
550B
2
DEC INC
–1CAM +1CAM STOP
7
8
9
MON
0
CAM
ESC
SET
F4
UP
IRIS
CLOSE OPEN
LEFT
4
5
RIGHT
6
AF
ZOOM
TELE
PRESET
RIGHT
6
AF
ZOOM
TELE
PRESET
RIGHT
6
AF
AUX
1
BUSY
AF
ZOOM
TELE
FOCUS
NEAR
WIDE
FAR
AUX
DOWN
System Controller WV-CU
1
550B
2
DEC INC
–1CAM +1CAM STOP
7
8
9
MON
0
CAM
ESC
SET
ZOOM
TELE
FOCUS
NEAR
WIDE
FAR
DOWN
System Controller WV-CU
550B
System controller
Note: When any peripheral is turned off and turned on again, the camera is also turned off and turned
back on.
57
PREVENTION OF BLOOMING AND SMEAR
;
;
;
;
;
;
When the camera is aimed at a bright light, such
as a spotlight, or a surface that reflects bright
light, smear or blooming may appear. Therefore,
the camera should be operated carefully in the
vicinity of extremely bright objects to avoid
smear or blooming.
Smear
Bright object
SPECIFICATIONS
WV-CW864E
Effective pixels
Scanning area
Synchronization
Horizontal scanning frequency
Vertical scanning frequency
Video output
Horizontal resolution
Vertical resolution
Signal-to-noise ratio
Minimum illumination
Zoom speed
Focus speed
Iris
Maximum aperture ratio
Focal length
H
Angular field
of view
V
Electronic shutter
AGC
SENS UP
BLC
Zoom ratio
Iris range
Power source
Power consumption
Ambient operating
temperature
Dimensions
Weight
WV-CW860
752 (H) x 582 (V)
3.65 mm (H) x 2.71 mm (V), 1/4”
internal/line-lock / multiplexed vertical drive (VD2)
15.625 kHz
50.00 Hz
1.0 V[p-p] PAL composite/75 Ω
more than 480 lines at centre (C/L), 570 lines at centre (B/W)
more than 400 lines at centre
50 dB (AGC OFF, weight on)
0.5 lx (0.05 foot-candle) C/L, 0.03 lx (0.003 foot-candle) B/W at SENS UP x 2 (AGC HIGH)
approx. 4.5 s (TELE/WIDE) in manual mode
approx. 6.0 s (FAR/NEAR) in manual mode
automatic (open/close is possible)/manual
1 : 1.6 (WIDE) - 3.0 (TELE)
3.79 - 83.4 mm
2.6 ° - 51.7 °
2.0 ° - 39.9 °
1/50 (OFF), 1/120, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s
ON (LOW)/ON (MID)/ON (HIGH)/OFF
max 32 times, AUTO/FIX
selectable ON/OFF (SETUP MENU)
x 22 +digital zoom x10
F1.6 - 22, CLOSE
24 V AC, 50 Hz
18 W, (59 W at heater ON)
220 V - 240 V AC, 50 Hz
18 W, (61 W at heater ON)
−30 °C - +50 °C (–22 °F - 122 °F) * See note.
200 mm (D) x 360 mm (H)
(7-7/8” (D) x 14-3/16” (H))
approx. 5 kg (11 lbs)
* Note: The picture quality and camera performance are not guaranteed until the inside temperature
rises up to –10˚C (14°F).
58
Auto focus
Auto mode
Auto pan key
Digital flip
Camera ID
Motion DET
Alarm IN
Alarm OUT
B/W mode
Privacy zone
Proportional PAN/TILT
Patrol
Cleaning
Image Hold
MANUAL/AUTO
OFF/SEQ/SORT/AUTO PAN/PATROL
SEQ/SORT/AUTO PAN/PATROL PLAY
ON/OFF
preset ID, camera ID, area title : up to 16 characters
ON/OFF
4 inputs (ALARM IN 1 - 4)
2 outputs (ALARM/AUX1, B/W/AUX2)
AUTO/ON/OFF
ON/OFF, up to 8 zones
ON/OFF
LEARN/PLAY/STOP, up to 30 seconds
ON/OFF
ON/OFF
Panning range
Panning angle setting
Panning mode
360 ° endless
possible (in auto-pan mode)
manual/sequential position/sort position/auto pan
manual : approx. 0.1 °/s - 120 °/s 8-steps/64-steps
sequence position : maximum approx. 300 °/s
0 ° to 180 °
manual/sequential position/sort position
manual : approx. 0.1 °/s - 120 °/s. 8-steps/64-steps
sequential position : maximum approx. 300 °/s
pan/tilt, lens, 64 preset positions, home position
Panning speed
Tilting range
Tilting mode
Tilting speed
Controls
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
ACCESSORIES
Alarm in cable .................................................................. 1 pc.
Alarm out cable ................................................................ 1 pc.
Connector for 24 V AC (only for WV-CW864E) ................ 1 pc.
OPTIONAL ACCESSORIES
Wall mount bracket ................................................................................. WV-Q110E
Sun shield ............................................................................................... WV-7176E
59
APPENDIX
Shortcuts
Shortcut operations are available for controllers having the CAM FUNCTION key. Entering from one to
three digits using the numeric key(s) and pressing the CAM FUNCTION key will create a shortcut to the
respective functions. The CAM FUNCTION key is abbreviated as [CAM FUNC] in the table below.
Function
Key
Selecting a PRESET position From #1 to #64
#1
[1] + [CAM FUNC]
#10
[1] + [0] + [CAM FUNC]
#64
[6] + [4] + [CAM FUNC]
AUTO PAN
ON
[6] + [5] + [CAM FUNC]
OFF
[6] + [6] + [CAM FUNC]
Speed Up
[6] + [7] + [CAM FUNC]
Speed Down
[6] + [8] + [CAM FUNC]
Setting Start Point
[6] + [9] + [CAM FUNC]
Setting End Point
[7] + [0] + [CAM FUNC]
Setting PAN Reverse
[7] + [4] + [CAM FUNC]
AUTO MODE
MODE Off
[7] + [1] + [CAM FUNC]
SEQ On
[7] + [2] + [CAM FUNC]
SORT On
[7] + [3] + [CAM FUNC]
ENDLESS PAN
On
[7] + [6] + [CAM FUNC]
Off
[7] + [7] + [CAM FUNC]
DIGITAL FLIP
On
[7] + [8] + [CAM FUNC]
Off
[7] + [9] + [CAM FUNC]
PROP. PAN/TILT
On
[8] + [0] + [CAM FUNC]
Off
[8] + [1] + [CAM FUNC]
BLC
On
[8] + [4] + [CAM FUNC]
Off
[8] + [5] + [CAM FUNC]
AUTO FOCUS
STOP AF On*
[8] + [6] + [CAM FUNC]
STOP AF Off*
[8] + [7] + [CAM FUNC]
AF On (Activate)
[8] + [8] + [CAM FUNC]
HOME POSITION
Move to HOME
[8] + [9] + [CAM FUNC]
B/W or C/L
B/W On*
[9] + [0] + [CAM FUNC]
B/W Off*
[9] + [1] + [CAM FUNC]
B/W AUTO*
[9] + [2] + [CAM FUNC]
CAMERA ID
On
[9] + [3] + [CAM FUNC]
Off
[9] + [4] + [CAM FUNC]
AREA TITLE
NESW On
[9] + [5] + [CAM FUNC]
USER On
[9] + [6] + [CAM FUNC]
TITLE Off
[9] + [7] + [CAM FUNC]
Function
EL-ZOOM
On
Off
RESTART
Begin
Memorize PRESET
Position #1
Position #10
Position #64
PATROL
PLAY
STOP
LEARN (Start)
IRIS
Open
Close
EL-SHUTTER
On
Off
Speed Up
Speed Down
AGC
On
Off
SENS UP
On
Off
Up
Down
SENS UP AUTO
On
Off
Up
Down
LL SYNC phase
INC
DEC
PAN
180 ° turn
CLEANING
On
Off
BW SW AUTO
30 sec.
60 sec.
300 sec.
600 sec.
Key
[9] + [8] + [CAM FUNC]
[9] + [9] + [CAM FUNC]
[1] + [0] + [0] + [CAM FUNC]
From #1 to #64**
[1] + [0] + [1] + [CAM FUNC]
[1] + [1] + [0] + [CAM FUNC]
[1] + [6] + [4] + [CAM FUNC]
[1] + [6] + [5] + [CAM FUNC]
[1] + [6] + [6] + [CAM FUNC]
[1] + [6] + [7] + [CAM FUNC]
[1] + [6] + [9] + [CAM FUNC]
[1] + [7] + [0] + [CAM FUNC]
[1] + [7] + [1] + [CAM FUNC]
[1] + [7] + [2] + [CAM FUNC]
[1] + [7] + [3] + [CAM FUNC]
[1] + [7] + [4] + [CAM FUNC]
[1] + [7] + [5] + [CAM FUNC]
[1] + [7] + [6] + [CAM FUNC]
[1] + [7] + [7] + [CAM FUNC]
[1] + [7] + [8] + [CAM FUNC]
[1] + [7] + [9] + [CAM FUNC]
[1] + [8] + [0] + [CAM FUNC]
[1] + [8] + [1] + [CAM FUNC]
[1] + [8] + [2] + [CAM FUNC]
[1] + [8] + [3] + [CAM FUNC]
[1] + [8] + [4] + [CAM FUNC]
[1] + [8] + [5] + [CAM FUNC]
[1] + [8] + [6] + [CAM FUNC]
[1] + [8] + [7] + [CAM FUNC]
[1] + [8] + [8] + [CAM FUNC]
[1] + [8] + [9] + [CAM FUNC]
[1] + [9] + [0] + [CAM FUNC]
[1] + [9] + [1] + [CAM FUNC]
[1] + [9] + [2] + [CAM FUNC]
[1] + [9] + [3] + [CAM FUNC]
Notes:
• Shortcut operations marked with * will change parameter settings only. Actual operation takes place
when the conditions for the changed settings are met.
• When entering shortcuts marked with **, “NO REGS. ; FLIP ON” may appear on the monitor. Re-enter
the shortcut.
• Shortcuts may be ignored while PAN/TILT, ZOOM or FOCUS is in operation.
• PATROL LEARN saves only [1] through [6]+[4], [1]+[6]+[9] and [1]+[7]+[0] in the memory.
• PATROL PLAY stops when a shortcut other than [1]+[6]+[9] or [1]+[7]+[0] is entered.
60
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
N1201-1022
2001
© Matsushita Communication Industrial Co., Ltd. All rights reserved.
V8QA5949BN
N 19
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Stampato in Giappone
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement