EasyLoader
EasyLoader
AV-2008, AV-2016
Dublo
(for LCD keypad)
Expandable to 16 or 32 zones Alarm
Control/Communicator with
DTMF Remote Control
Installation and Operation Manual
Version 3.05
Edition I
This product is subject to continuous enhancements and therefore
specifications may be changed or altered without prior notice
Item 4712_DBL
Table of Contents
Contents
Page
SECTION I: SYSTEM FEATURES ..................................................................................... 4
1. INTRODUCTION...................................................................................................... 4
1.1 
1.2 
1.3 
1.4 
1.5 
1.6 
General Description.......................................................................................... 4
AV-2008, AV-2016 Dublo Built-in Features ................................................... 4
Programmable Features .................................................................................... 5
Alarm and Power Outputs ................................................................................ 5
Ordering Information........................................................................................ 6
AV-2008 Dublo Technical Specifications........................................................ 7
SECTION II: INSTALLATION ..................................................................................... 9
2. MOUNTING .............................................................................................................. 9
2.1 
2.2 
2.3 
Control Panel Mounting ................................................................................... 9
Wiring AV-208 and AV-816 Expander............................................................ 11
Keypad Wiring.................................................................................................. 12
3. ALARM OUTPUTS................................................................................................... 13
3.1 
3.2 
3.3 
Sirens ................................................................................................................ 13
Remote Indication Terminals ........................................................................... 14
Wiring and Connection of Relay Module......................................................... 15
4. WIRING AND POWERING UP ............................................................................... 15
4.1 
4.2 
4.3 
4.4 
4.5 
4.6 
4.7 
4.8 
Grounding – Lightning Protection.................................................................... 15
Back-up Battery................................................................................................ 15
Before Powering Up ......................................................................................... 16
Connecting Smoke Detectors ........................................................................... 16
Telephone System Dialing................................................................................ 17
SVM – Voice Module ...................................................................................... 17
Remote Key and Wireless Arming & Disarming ............................................. 18
Remote Access via DTMF ............................................................................... 18
SECTION III: LCD KEYPAD ....................................................................................... 21
1.1 
1.2 
1.3 
1.4 
1.5 
1.6 
Standard Keypad Functions.............................................................................. 21
Hold-Down Functions ...................................................................................... 22
Keypad Sounder................................................................................................ 26
LED Indicators.................................................................................................. 27
Arm and Disarm System................................................................................... 28
Auto Arming..................................................................................................... 29
2
SECTION IV: PROGRAMMING.................................................................................. 30
1. SYSTEM CODES ...................................................................................................... 30
1.1  User Code Programming via AV-706, AV-707 ................................................... 31
2. FEATURE PROGRAMMING AT INSTALLER LEVEL ........................................ 32
2.1  Programming Table AV-2008, AV-2016 Dublo (V 3.05) ............................... 32
2.2  Introduction ...................................................................................................... 37
2.3  Programming Sheet Explanation ...................................................................... 37
2.4  Glossary of Programmable Features................................................................. 39
2.7  Step - By - Step Programming.......................................................................... 44
2.8  Reset System to Default Programming............................................................. 46
2.9  Dialer- Communicator; explanation and Programming ................................... 46
2.9.1  Deleting Telephone Numbers............................................................................ 48
2.9.2  User Programming of ‘Follow-Me’ Telephone Number................................... 48
2.10  Quitting Programming Mode ............................................................................. 48
2.11  Verification of Current Programming ................................................................ 48
2.12  Downloading from a computer........................................................................... 48
4. TROUBLESHOOTING ............................................................................................. 54
SECTION V: Wiring Diagram........................................................................................ 57
SECTION VI: Index........................................................................................................ 58
Av-Gad Limited Warranty .............................................................................................. 60
@ All Rights Reserved to Av-Gad Systems Ltd, Tel Aviv, Israel. POB 49 080 Tel-Aviv, Israel. May 2007/ VER. 3.05, AV-2008, AV-2016 Dublo. Item 4712_DBL
3
SECTION I: SYSTEM FEATURES
1. INTRODUCTION
1.1  General Description
Av-Gad's EasyLoaderTM AV-2008, AV-2016 Dublo is an expandable microprocessor based
intruder alarm panel with integrated communicator. Use expander AV-208 for AV-2008 Dublo
and expander AV-816 for Av-2016 Dublo. Series 2000 represents the state-of-the-art in userfriendly, reliable alarm control panels for security requirements of small and medium-size
commercial, residential, and industrial installations.
 Av-Gad's EasyLoaderTM AV-2008, AV-2016 Dublo versatile control panels meets and
surpasses all requirements for reliability and maintainability and provides the added benefits of
easy installation and simple operation.
 The AV-2008, AV-2016 Dublo are compatible with AV-705, AV-706, AV-707 and AV-707B
LCD keypads.
 The AV-2008, AV-2016 Dublo comprises an enhanced power supply, improved electronics,
and additional signaling indicators.

Version 3.05 news: , “2nd Aux. Key at last zone” 075-5, “Enable buzzer at home mode” 078-1.
1.2  AV-2008, AV-2016 Dublo Built-in Features





















Accepts Normally Closed or Normally Open alarm devices
All features are programmable via system keypad
Automatic battery test upon arming and during Disarmed or Armed mode
True low battery indication
Built-in central station Contact ID communicator and dialer
Chime programmable for each zone
Digital zone status display
Double-Pole zones. Tampering indication for each zone
Keypad sounder during local alarm
Local clock and date
Modulated tone siren from 24H and panic zone(s), 3-tone alarm from burglary zones
Programmable 4 and six outputs drivers for remote signaling and reset of smoke detectors
Programmable 8 to 32 EOL resistor zones, or non-EOL zones
Pulse-operated battery charging circuit
Two dialing modes: Pulse or DTMF
Signals to central station monitoring (via telephone or wireless transmitter)
Remote control via DTMF phone and Home Automation
Up and Download from a computer, or via telephone line
Up to 250 alarm logs, with event time
Up to 16 user codes, each code one to six digits. One installer code, access control code
Up to 24 EOL supervised double-zone. One Panic zone at keypad
4
1.3  Programmable Features
 Up to Thirty Two End-Of-Line zones (with AV-2016+AV-816), EOL zone enable or disable
 Individual entry delays for two zone groups.
 Automatic bypass of open (troubled) ‘instant’ zones upon arming
 Selective and Zone Group Bypass (Group Shunt for Home Mode)
 24-hour zones, fire zone
 Zone types: Delayed, Follower, Fire, Not in use, Day, Tamper, Panic zone and more
 Selectable response time for individual zones
1.4  Alarm and Power Outputs
 Five programmable open collector output drivers for remote alarm signaling
 Contains auxiliary output for electric strike operation
 Communicator to central station, with AV-707B three Panic reported via Contact ID
 Keypad sounder alarm programmable by zone
 Two timed siren outputs, protected by separate fuses
 Variable sirens alarm sound for different types of zones
 Two separate fused protected auxiliary power (12V)
 Signal test to central station, signaling time and day are programmable
 Programmable ‘Bell Mode’
 Remote Signals:
 24H-zone Alarm
 On/Off (Arming/Disarming) indication
 Central station Signal Test. Transmitting time is programmable
 Three Panic types, Tamper alarm
 Programmable output for each zone or event (SLO output)
5
1.5  Ordering Information
Item Code
Description
AV-2008, AV2016 Dublo
8 + 1 or 16 +1 double-zone Expandable Alarm Control Panel and
Communicator and Dialer. Supports AV-705, AV-706, AV-707
keypad. Approved for EEC telephone system
AV-208
8 zone expanding module for AV-2008 Dublo
AV-816
16 zone expanding module AV-2016 Dublo
2008_3DBL
Board only for AV-2008 Dublo
2016_3DBL
Board only for AV-2016 Dublo
TMP
Tamper switch with wires for main alarm metal box. Not
supplied, requires special order
AV-705
AV-706
AV-707
4-wire Keypad. LCD Display, 4 LEDs, 12 silicon rubber keys.
Built-in Micro-Processor.
AV-707 is available in few colors. Tamper switch is optional for
Av-705, AV-706 and AV-707
5003TER
Fuse-protected 220V step-down to 16V-1.2A AC transformer for
AV-2008 Dublo Series
5005TER
Fuse-protected 220V step-down to 16V-1.7A AC transformer for
AV-2016 Dublo Series
RELAYMO
Relay module for driving self-powered siren in Series 2000.
(Used in France, Italy, UK and other countries.)
SVM-40/60
Speech module, record & play, message stored without power, 40
or 60 seconds message. Two channels. For message recording an
on-board microphone is included
AV-21, AV-21B
and AV-40
Extra 12V (1A or 4A) power supply and charger, supplying the
power for large installations. AV-21 supplied as PCB, with AV21B the PCB housed in metal box. AV-40 is 12V 4A with battery
monitor and controlled charging.
6
1.6  AV-2008 Dublo Technical Specifications
Operating Temperature
Relative Humidity
Input AC Power
Dynamic Inner Memory
Auxiliary Power Output
-10C to 60C
80% maximum
16V AC step-down Transformer 1.2 Amp
EPROM and SRAM
13.8 Volts +/- 5%, Regulated
Short & Overload circuit protection
Siren Outputs (x2)
Siren or Bell Selectable
Bell Mode: 14V DC-2 x 0.7A (1.4A)
Siren: 8 Ohms, 20W Max.
Programmable Dialer: 3 telephone numbers Pulse Dialing parameters programmable
& 1 Follow Me telephone number (4 phone DTMF: Touch Tone dialing 
numbers)
Max. Telephone number length: 16 digits
Contact ID central-station communicator
and 4 pauses
Remote Indications on Wire Terminal
Open Collector type output
300 mA Max. @ 12V DC
EOL Zone Loop Resistor (Burglary)
2,200 Ohms, 0.25W, +/- 5%
EOL Zone Loop Resistor (Tamper)
4,700 Ohms, 0.25W, +/- 5%
Zone Loop Voltage
5 to 6.5V DC
Zone Loop Current
3 mA with End-Of-Line Resistor
Line Protection
Zone line shorting, cutting, high voltage
lightning protection, RF Metal Screen,
Electro Static Discharge Traps, RF Filters.
Telephone line Lighting protection circuit
Auxiliary Power (Max.)
13.8V DC 0.9A Combined AUX. Power
and outputs
Battery Charging Current (Max.)
550 mA, current limitation
Battery Test: Indication at keypad or remote Performed at 0.5A load for 1 second.
indication via communicator
Low Battery indication below 10.5V
Tested upon Arming, and every 4 minutes
during Armed, every 1 hour during
Disarmed
Standby Power Consumption at disarmed
110 mA, +/- 10 %
mode, and Keypad display is Off
Max. Remote Station (Keypads)
Three keypads of AV-706, AV-707
AV-2016: Five of AV-706, AV-707
Remote Station Current Consumption
AV-706/7: 60 mA. AV-705: 30 mA
Housing
Anodized, lockable large metal box
Epoxy anti-static powder painted
7
Housing Dimensions
AV-2008 (ABS): (H)30, (D)9, (W)23 cm
AV-2016 (MTL): (H)32, (D)9, (W)36 cm
AV-2008: 2.3 kg. 6 PC’s. per box
AV-2016: 3.6 kg. 3 PC’s. per box
Auxiliary Power: 1.5A Electronic
Sirens: 2 X 1.5A Electronic
Backup Battery Fuse: 3A Electronic
AV-2016 Keypad Power: 1.5A Electronic
Gross Shipping Weight
Fuses: Electronic Resetable Fuse
Av-Gad Systems Ltd. reserves the right to modify and upgrade products without prior notice.
Electronic Fuse Overview
The Electronic Fuse device included as a series element in electric circuit. In response to an over current it
protects the circuit by going from a low-resistance to a high-resistance state that reduces the current to a level
that’s safe for the circuit elements. The change in resistance is the result of a rapid increase in the
temperature of the device. Like traditional fuses, Electronic Fuse devices interrupt the flow of dangerously
high current. However, unlike traditional fuses, they automatically reset after the fault cleared and power to the
circuit removed. Because they are solid-state, Electronic Fuses are also better able to withstand mechanical
shock and vibration, and provide reliable protection in a wide variety of applications. In case of over current,
carefully touch the fuse body (yellow round disc), hot body means the Electronic Fuse in protection mode,
disconnect the load and wait 2-3 minutes until the fuse body get cooler.
Tips to first time installer
If you are a first time installer, do not hook up any remote sensors at first. The most common
confusion comes about when the alarm will refuse to arm, because a zone is “troubled”.
Complete the power supply, siren, keypad and strobe wiring, and for the moment connect ALL
the zone terminals to –V. This will simulate a system with all zones looped out through closed
switches. The alarm is supplied already programmed with an “average” list of settings (default)
and can be used straight away, a few of the program locations may have to be changed to suit the
actual sensors and output devices used.
 Read this manual carefully, it looks complicated, but all the information is there
 Carefully read the manual supplied with your LCD keypad
 To start with: Hook up the keypad, connect all zones to –V, power-up by applying AC only
 In case the keypad displays ‘garbage’ verify the minus (-V) wire connection
 Arm and disarm the system, when the Status LED light (not blinking), enter your master code; 1234
 Try the hold-down functions. Hold each key for approximately 2 seconds, press # (enter) to confirm the
hold down command
 Set the system time by holding-down key ‘0’ then ‘1’, set time in 24H format, blinking ‘Set Time’ stop
 The default programming is set for siren alarm device that requires 12V to alarm (Bell Mode)
 Connect the strobe light to the SLO output (requires programming). The SLO supplies –V during alarm
 Make sure you are using the Earth terminal
for Grounding; it is not a minus terminal
 Typing six erroneous codes will lock the keypad keys for 30 seconds
 Fast test for AV-2008, AV-2016 Dublo: Verify “Dial LED" Self Test at Initialization (STI) - Blinks for the first
50 seconds after power on, confirms panel is operative, from keypad wait to six beeps to confirm
communication OK.
8
SECTION II: INSTALLATION
System planning
When the panel reaches you it features set at “Factory Defaults”. This done for testing purposes
and also for installation if required without first entering to programming. This present program
is referred to as ‘Factory Defaults.’ The engineer should be familiar with all the features and
options before attempting to program. System supplied with or without transformer according to
approval requirements in each country. Specify and order the keypad (several types available).
Default arming code is 1,2,3,4. Default programming code is 1,9,9,4.
2. MOUNTING
2.1  Control Panel Mounting
Refer to detailed wiring diagram on section V.
Select a mounting location accessible to the following:
1. A continuously powered (non-switched) AC power source, compatible with step-down
transformer. Make sure the mains (110 or 220V) are fused
2. A cold water pipe Ground, ideally no farther than 3 meters (10 feet) from the panel. Use
16 AWG (0.5 mm2 wire)
3. Telephone line socket
Always install the control panel box in a hard-to-access location.
Locate one of the Keypads near the Entrance/Exit door.
Install a tamper-switch to prevent opening or removal of the control panel box. Connect the
tamper-switch to a 24H zone.
Zone Wiring Mode
Via programming, select either End-Of-Line (EOL) Resistor Protection, or non-EOL mode.
If EOL mode selected (recommended), install the EOL Resistor (2.2K/0.25 or 0.5W) inside the
detection device (e.g. PIR, Magnetic Switch). To disable EOL enter ‘0’ to EOL zones address.
Note: ‘Zone’ and ‘Sector’ are interchangeable terms in this manual.
IMPORTANT! Never run wire zones alongside telephone wires, high voltage wires, or
transmitting antennae.
Double-Pole Zone wiring
This feature saves on wiring and doubles the zone quantity by using two wires instead of four,
for both TAMPER and ALARM indications.
Recommended to always use an EOL resistor; EOL prevents EMI and RFI interference
9
To activate Tamper Alarm, fit the zone with two EOL resistors, program ‘Enable Zone Tamper’
feature (address number 144, 145, 146, 147) and enable ‘EOL Resistor Zone’, entering the data
at address (140, 141, 142, 143).
To enable the EOL mode program the zone selected as EOL zone. For example: To enable zones
1, 2, 3 as EOL zones; in address 144 program 1, 2, 3 removed.
Any EOL zone will report Tamper alarm in case of zone shorting (if it has been EOL
programmed). To enable Tamper zone as 24H zone refer to address 075/1.
Upon Tamper alarm, a ‘t’ displayed, followed by the zone number. To disable Tamper alarm,
hold down key ‘9’. To display Tamper zone history, hold down key ‘0’ then key ’3’.
Use PIR, other sensor or Siren box alarm device that contains two separate switches or relay
contacts: One for Alarm and one for Tamper. Connect each contact to a different EOL resistor.
Alarm contact connected in series with 2.2K and Tamper contact with 4.7K resistors. Both
resistors supplied with each system. When using Av-Gad Eye-Spy II PIR wiring is simplified, as
the Alarm and Tamper EOL resistors are built-in the sensor.
Figure 1: Double-Zone Wiring
Some countries are used to different double-pole wiring as shown in figure 1A. For this wiring,
follow the drawing. European double-pole wiring requires 1.5K resistors (1.5K resistors not
supplied).
10
PIR Sensors wires Terminal
Tamper
N.C.
Power
Alarm
C
N.C.
C
-V
+V
1.5K Ohm
1.5K Ohm
Zone Common
Zone Input
+12V
Figure 1A: European Double-Pole wiring drawing
2.2  Wiring AV-208 and AV-816 Expander
Screw
AV-816 board
SIR1 AND SIR2 FUSES
D34
VA1
C16
R43
+ +
R1
Zone
R2
1.25A
R3
17
F10
+ +
D10
19
D3
D2
R6
20
-BATTERY
R7
+BATTERY
R8
D18
+
21
+
R40
R93
VA1
R59
R97
CB E
U7
R94
Q1
D25
R37
R99 R100
23
SIR1
RF1
SIR-
C19
U1
KEY
R10
Connecting the AV-208 or AV-816 Expander
RF4
VA6
R102 R101
R62
VA5
RN1
R13
28
R14
(-)
29
R51
D21
R33
R24
R22
R26
R16
with screws
3. Insert the AV-816 plug to AV-2008 J1 socket (as drwaing)
R98
R53
U3
VA8
R12
27
1. Disconnect AC and Battery power
2. Attach the board to metal box and with screws
R36
R60
+
R11
26
D14 D17
D16
C11
SIR2
R9
VA2
25
R52
D15
VA2
(-)
+12V
R41
D19
D9
AC
C1
D20
D4
R44
BAT. FUSE
AC
22
24
AV-2008 Dublo board
D5
R46
R5
(-)
+
C12
D1
F11
+
+
C13+
D32
R4
18
C15
C17
Q5
R42
1.25A D33
R20
30
R35
31
R34
J1
32
C10
(-)
+ +
VA9
VA3
U2
AV-GAD AV816
Colored Wire
Screw
J1
+12V -12V
AV-816 EXPANDER
Figure 2: Expander Wiring
Mounting
Place the AV-208 expander board on the left side of the AV-2008 Dublo board as the drawing
shows. The AV-208 supplied with four plastic holders to assemble the board to metal box.
Important! The AV-816 is compatible with AV-2016 Dublo and require different mechanical
setting that is not available in AV-2008 metal box.
Connection
Make sure power and battery are disconnected. The AV-816 fits the AV-2016 only.
11
Plug the wires connector of AV-208 or AV-816 to J1 socket at the AV-2008, AV-2016 Dublo,
refer to figure 2 drawing.
Zone Wiring Mode
Via programming, select either End-Of-Line (EOL) Resistor Protection, or non-EOL mode.
If EOL mode selected, install EOL Resistor (2.2K/0.25 or 0.5W) inside the detection device (e.g.
PIR, Magnetic Switch).
To enable EOL mode programming and resistors required.
To enable the Tamper Alarm of each zone, refer to the programming table and set the required
zone by programming address number 144, 145, 146, 147.
Wiring details are available in the AV-2008 Dublo manual, see Double-Zone wiring chapter.
Programming
Program the ‘Zone in Use’ feature for the required zones (address 102 and 103). By default,
program zones 1-16 were set as ‘Zone in Use’.
2.3  Keypad Wiring
Up to three AV-706 or AV-707 Keypads can be connected to AV-2008 Dublo, up to eight at
AV-2016 Dublo Control Panels.
Important: Consider adding a power supply when using more than six keypads
Connect all keypads in parallel. Do not connect keypad with power on. Each keypad contains
four wires terminal:
Red  (+) Power, connect to + Aux. Power
Orange  System Data, connect to OR
Black  (-) Power, connect to - Aux. Power
Yellow  System Strobe, connect to YE
For proper connection, refer to wiring diagrams on next page and at the end of the manual.
IMPORTANT! Never run Keypad wires alongside telephone wires, high voltage wires, or
transmitting antennae. Wire the keypad wires separately and not in same cable with other
devices (telephone, PIR's etc.). Do not use the keypad wires for supplying power to sensors
or other devices. Keypads have no polarity protection; verify 12V power carefully during
wiring.



Wire length for each should not exceed 200 meters (using 0.5 mm2 wires).
If installation requires keypad wire length of more than 100 meters, or more than five
keypads:
1. Add a 470-ohm resistor between +12V and YE terminal in the control panel
2. Use two wires for the –V that supplies the keypad power
Power at Keypad should be a minimum of 11.5 Volts.
AV-705, AV-706, AV-707, LCD keypads are compatible with PRO and Dublo panels, for
keypad operation and programming refer to separate manual included with the LCD
keypad.
12
Note: If a No Communication message displayed and keys do not respond, it is an
indication that the keypad is not communicating with the panel. Check wiring. Polarity
error may blow the panel fuse.
Panel
Panel
Wrong Wiring
Correct Wiring
Figure 4: Keypad best way wiring
For trouble free operation follow the recommended wiring as shown in figure 4 drawing, wire
each keypad to the panel directly, avoid to run wires from one keypad to next (as shown the on
the ‘Wrong Wiring’).
Keypad Tamper Switch
The AV-706TP and AV-707BTP keypads (keypad with tamper switch) contain a Tamper switch
that activates upon removing keypad’s front part. Connect the Tamper switch to Tamper, Day or
24H-type zone. For connection, refer to keypad’s wiring diagram.
3. ALARM OUTPUTS
3.1  Sirens









AV-2008, AV-2016 Dublo control panels enables driving of two separate sirens.
Use 8 to 16 ohm speaker siren, 14 watts minimum, or 12V DC siren (Bell).
Bell mode is available via programming.
Speaker siren issues a multiple-tone alarm.
Enclose the outdoor siren in a metal box tamper-switch protection.
Protect siren or bell box with tamper-switch connected to a 24H zone.
The control panel contains two siren outputs, for internal and external siren, individually
protected by fuses.
If Siren mode selected, use speaker type siren with a minimum power of 15W, 8 Ohms
impedance. Enclose the outdoor siren in a metal housing, with anti-tamper switch
protection.
Siren mode (Bell) is default-set at factory. Default factory program is for DC type sirens
(Bell).
13







The alarm issued by the Siren (not Bell mode) differs according to the type of zone.
‘Bell Mode‘ converts Siren outputs into 13.6V DC outputs (no sound is issued). Bell mode
is applicable for driving self-powered sirens or bells, or combined sirens and strobes.
In Bell mode, connect only Bell or sirens that contain a 12V sound driver or electronic
modules. Bella sirens are compatible and feature high sound level at very low current use.
Self-contained Bell mode is programmable (address 071). This mode allows connection of
Bells or Sirens that require 12 – 13.6V DC at ideal and 0V during alarm. The Bell output
voltage regulated at about 13.6V. For self-contained siren it is recommended using Av-Gad
Bella 2 siren plus Xenon strobe light.
Contact manufacturer's consultant before connecting higher power loads.
To connect self-contained sirens, Bells, and inner-oscillating sirens, refer to address 072;
see Bell mode.
Contact manufacturer's consultant before connecting higher power loads.
3.2  Remote Indication Terminals
Indication
Application
ON
OUT 1 (A1)
(-V) on closing (Arming) or activate ADSL module AV-03 (072-4)
Programmable. (-V) during alarm from the programmed zone or
event (tamper alarm or panic)
Programmable.(-V) during alarm from the programmed zone
Resets only upon disarming (SLO is a non-timed output).
Most useful for strobe light connection.
Programmable.(-V) during Smoke reset or Code 7 entry (070-7)
SLO Output
SLO 1 Output
Warning: The remote indications are capable of driving maximum 300 mA, overloading
or applying +12V to the remote indications is dangerous and not assured by warranty
To drive a low current Strobe Light (Xenon Tube type) consuming up to 300 mA, connect the
strobe to SLO. Do not connect simple bulb type strobe light to any of the outputs, if using such
strobe light use a relay.
Inverting output polarity - Enables programming the listed outputs to supply float output (0V)
during alarm and -V at ideal. Refer to address 073-8.
In case other features selected for the same output, this feature is not applicable.
When connected a relay the remote indication, connect a diode must to the relay coil in reserve
polarity to the supplied voltage, or use AV-01/02 relay module. For LED driving, connect a
2.2K resistor in series.
Hardware Tests for Outputs
This feature enables testing of devices connected to the remote indications.
In programming mode, using 200 + commands:
30 - On Output: ON
31 - On Output: OFF
32 - A1 Output: ON
33 - A1 Output: OFF
14
34 - A2 Output: ON
35 - A2 Output: OFF
36 - SLO Output: ON37 - SLO Output: OFF
38 - SLO1 Output: ON
39 - SLO1 Output: OFF
42/43 LCD display - Display pattern test
3.3  Wiring and Connection of Relay Module
The Relay Module enables connection of EasyLoader 2000 Series panels to most types of Bells
and self-contained internal battery Bells or Sirens (the term ‘Bell’ will apply to both Bells and
Sirens).
Trigger the Relay Module via the siren output of the control panel. The power which drives the
Bell may be supplied either from the Aux. Power of the control panel, or from an external power
supply in case the Bell requires higher current than the 0.7A supplied by the control panel.
Full installation details enclosed with the relay module.
4. WIRING AND POWERING UP
4.1  Grounding – Lightning Protection
The control panel must be earth grounded for lighting protection to work effectively, and in
order to prevent RFI and EMI interfaces. Attach the ground connection to a verified cold-water
pipe using a minimum 16 AWG (or larger) wire, or according to the country grounding standard.
Run the ground wire via the shortest possible route.
System grounding is compulsory. For trouble free system, use a good ground.
Connect the Grounding wire to main board and to the metal box.
Note: Connect the Ground wire to the terminal marked
. This is not a Minus (-V).
Beware of static discharge; before handling the main board touch a grounded metal.
Before grounding the system, make sure ground properly connected and does not transfer high
voltages. If ground is not available, run a ground wire and connect to a cold water pipe as close
as possible to earth.
4.2  Back-up Battery
Connect the Battery in the correct polarity!

The system's Red wire is the positive pole (+) and the Black wire is the negative pole (-).

The battery will provide power back-up in case of AC power failure.

Connect back-up battery to ensure proper operation of the system.

Recommended battery: 5 to 7.2 Amperes per Hour (AH), 12V SLA (Sealed Lead Acid) type.

7.2 AH battery provides power back-up to control panel and to a single LCD keypad for
approximately 6 to 8 hours.

An Electronic Fuse protects the battery circuit.
15
4.3  Before Powering Up









Place the Control Panel in a well-ventilated location, as far as possible from heat sources.
High power RF transmitters place at least 2 meters away from the control panel.
Check for proper grounding. Un-charge your body by touching the Ground terminal.
Make sure polarity of detectors, keypads and other devices is correct.
Connect a momentary voltage to the siren; making sure a ‘beep’ is sounded. If there is no
beep, check for a short circuit or improper connected wires.
Initial power-up with AC transformer only. Connect battery only after keypad and sensors
seem to be operating well. (Do not Power-up with battery alone.) Verify power polarity of
keypads.
Do not connect any devices to the battery terminals.
The AV-2008, AV-2016 Dublo contains Electronic Fuse, in case the fuse blows return to
factory for replacement. Refer to further details at page 9.
AV-2008, AV-2016 Dublo: Observe the dial LED Self Test at Initialization (STI) - Dial
LED blinks for the first 50 seconds after power on, confirms that the panel is operative.
Also, wait for the six beeps from the keypad to confirm that the keypad is communicating
with the panel.
4.4  Connecting Smoke Detectors
AV-2008, AV-2016 Dublo accommodate Heat, Ionization or Optical type 12V Smoke
Detectors. Connect up to five smoke detectors to each zone. Because most smokes are Open
Collector output, programming a zone as Fire, Normally Open (N.O.) zone type will be
automatically enabled. It means; a zone programmed as Fire (but no EOL) the zone will be also
N.O. type. In this case, do not connect the EOL resistor as wiring diagram show. The smoke
detector LED will remain constantly lit and the relay or output will remain in ‘Alarm’ until the
smoke detector power is disconnected for a short while (reset).

The AV-2008, AV-2016 Dublo Series is compatible with 12V smoke detectors with open
collector or relay (-) output on alarm.
Reset Relay (or switch)
Relay Module like AV-01 or Switch mode, should be Normaly Close (N.C.)
For reset cut power for Smoke during 2 Sec's
Av-Gad Systems Panels
Reset Switch or Relay Module
EOL resistor 2.2K
Resistor
-V at alarm
-V
N.C.
+
LAMP
-
12V, Aux. Power
- +
-V
TFB 110
TFB 110
+
-V
-
LINE
+
-
To Zone Input
+12V
Draw: W2/SMK868NW
-V via the Reset Switch
Do Not! Connect EOL Resistor at last smoke
Figure 6: T F Smoke Detectors b a s e s m o k e w i r i n g t o A v - G a d p a n e l s
16
To reset AV-2008, AV-2016 Dublo smoke detector program the SLO 1 output to drive -V
while holding-down key 9 (a momentary switch or relay that disconnects power during 2-3
seconds to smoke detector after a smoke alarm). Refer to smoke wiring diagram figure 6.
 When Fire Alarm occurred, hold-down key ‘9’ for reset, enter valid code to disable alarm.

4.5  Telephone System Dialing
It’s recommended to connect the control panel to an independent telephone line, if a device is in
parallel with the alarm panel, this may grab the call first (like a message answer/fax) during
remote up and download.
Do not connect fax or answering machine in parallel on the same telephone line.
In case of alarm the dialer dials to the programmed numbers, siren sound or voice message (if
SVM-40 connected) will be transmitted to the telephone. Voice module types SVM-40 or SVM60 are compatible with AV-2008, AV-2016 Dublo EasyLoader panels. The voice module will
apply spoken message over the telephone upon alarm.
Default dialing mode is DTMF. If PULSE dial is selected, the default is European Make/Break
rate of 40/60 milliseconds (in Pulse dialing). The Make/Break rate is programmable.
Dialing mode is programmable (refer to programming sheet addresses 088 and 089).
Connect the telephone line to ‘TEL-LINE’ terminal, if handsets connected to same line connect
them to ‘PHONES’, when system attempt to dial the ‘PHONES’ is disconnected. Do not
connect to ISDN or other digital telephone system. Most ISDN converters have an Analog line;
connect the Analog line of the ISDN the TEL-LINE terminal. Option: To protect your line add
the Tele-Spy, it is a 24H telephone line monitor separate module. Note: To perform telephone
line test enable Dial Tone detection at address 083.
For telephone line with ADSL add the AV-03 module for filtering and line cut, refer to address
072-4 “Activate ADSL filter (AV-03) line cut”. If feature selected the ON output deliver –V
when dialing starts to activate the relay of AV-03.
For AUSTEL installations: At address 074 enter 8, at address 087 enter 2 (maximum), don’t
connect any phones in parallel with TEL-LINE terminal. Software Dial Tone telephone monitor
is included, refer to address 094, 076 options 5,6. Dialing problems may occur when system
telephone line is connected to Telstra Duet system or similar.
4.6  SVM – Synthesized Voice Module
The SVM-40 and SVM-60 Synthesized Voice Modules and are optional (not supplied with the
panel). The SVM allows the recording and playback of two messages, with optional playback
through an external speaker (not included). SVM-40 message duration is 40 seconds; SVM-60
message duration is 60 seconds. The SVM contains an on board microphone.
The SVM is a high technology device, electronically stores messages with or without power.
The SVM is as a digital message source in Series 2000 Alarm Control Panels, telephone dialers
or in other applications. The SVM supplied audio is capable to drive audio amplifier, message
center, automatic dialer or other device.
17
When connected to AV-2008, AV-2016 Dublo, program the SVM option (at programming table
072-7). Follow the wiring procedures (included in SVM manual) simulate alarm, the panel will
dial first the Communicator telephone number (telephone number 2 and 3), then dial to other
programmed numbers.
After dialing, the panel will trig the SVM to send the recorded message. If address 071 (1) is
programmed Telephone 1 is erased within arming and disarming.
4.7  Remote Key and Wireless Arming & Disarming






The AV-2008, AV-2016 Dublo enables Arming/Disarming by remote momentary or latch
key-switch (as programmed in address 071), which is connected to terminals ‘KE’ and
‘- Aux. Power.’
When using remote key-switch, wire length should not exceed 10 meters.
A Momentary pulse (momentary trig) between ‘KEY’ and ‘-V’ terminals will Arm and
Disarm the control panel. (Before arming close ‘instant’ and ‘24H’ zones)
System reverts to previous status with next momentary pulse. (Refer to AV-2008, AV-2016
Dublo Wiring Diagram.)
Arming by key will cause a long beep at the keypad if "Enable two siren beeps at disarm"
(073 - 6) is programmed.
For Arming/Disarming via Wireless Radio Remote, connect receiver's relay to ‘KE’ and
‘- Aux. Power’ terminals. Verify the receiver relay mode, momentary, or latch, and set
system accordingly.
4.8  Remote Access via DTMF
General Description
Remote DTMF enables remote control of the alarm panel form a DTMF phone, this unique
feature provides Home Automation function and other functions as detailed below.
DTMF commands are possible when the panel call your phone, or by calling the panel. The
DTMF remote control functions:
 Check the status of the control panel (Armed/Disarm, Alarm in progress)
 Arm or disarm the control panel
 Bypass zones or clear all bypassed zones
 Stop the dialer report during alarm
 Momentary activate A1 (alarm) output for three seconds
 First Alarm indication - by a number of beeps per zone, special tune for Panic alarm
The same options are available when a call is received from the control panel during an alarm
condition.
To enable the DTMF control program address 076/4 “Enable remote access by telephone”, and
076 - 2 “Enable A1 activation by telephone”.
Keypad online conformation and DTMF functions history
When the control panel detects the first DTMF key, five short beeps will be sounded at the
keypads. The keypad activation shows the user at the remote site that a DTMF connection takes
place (in case of mistaken connection or similar).
18
During the remote access the keypad display 'd' and all LEDs blink fast from time to time.
At call ends, the three short beeps will be sounded at the keypads. When the user code is in
process, the keypad display shows a line for each code number entry (disclose the code), then
each DTMF number pressed show the received number.
History log: Each call, confirmed by a valid user code, is recorded in the events history. Each
"Arming/Disarming" is recorded in the events history.
"Last users" history will display 'ut' for "user "telephone, followed by the User number.
Notes: 1. The keypad buzzer or other loud sounds may jam your DTMF entries, in case the
keypad is close to your DTMF telephone, during testing disable the buzzer.
2. When entering the DTMF commands wait for “quit” period, if entering commands
during the system confirmation tunes, or other tunes the panel may miss the DTMF
entries.
The panel calls the user during alarm
When the control panel calls the user during alarm, it will first generate the siren sound for about
30 seconds (to shorten this feature at address 085 “Tel. Message Time”, to 30, as default is 50
seconds). The siren sound will stop ten (10) seconds before the end of the call and a greeting
tune will be sounded, after the greeting tune enter your code followed by #. To stop the dialer
enter 6#, to get panel status enter 7#, to disarm the panel enter 2#. To end the process press 9#.
The control panel will answer the call after the number of rings programmed at address 091 (or
following the “bypass answering machine" procedure).
Commands
Each command must be followed by the '#' key (Enter) in the remote phone. The control panel
waits 4 seconds between the keys typed. When this time expires, previous keys input will be
discarded.
The key '*' cancels previous input. It’s recommended to start with "learn" function [8X #] to
identify the various confirmation tune.
The commands:
[0 X #] - Bypass zone (# is the Enter key)
X is Bypassed zone 1 to 8
To clear all bypassed zone: 0 9 #
The zone bypass command is valid only when the system is in Disarm position and not in Alarm
position.
[1 #] - Arm control panel. The control panel will be armed even with open zones. After the
arming, a confirmation tune followed by an "armed" tune will be sounded ("Armed" tune: Short
beep followed by a long tone.).
The user can wait a few seconds to be sure that no alarm has been caused by open zones. In this
case, an Alarm tune (siren sound) will be sounded.
[2 #] - Disarm control panel. The control panel will be disarmed. A confirmation tune followed
by a "disarmed" tune will be sounded ("Disarmed" tune: Five short beeps).
[31 #] - Activates A1 output for 3 seconds (enabled by programming 076-2)
19
[33 #] - Activates SLO 1 output for 5 seconds, keypad sounds 7 short beeps (enabled if SLO 1
is not used with zones alarm events or for Chime activation)
[6 #] - Stops dialer. The dialer will stop calling the programmed telephone numbers. This will
affect only the current dialing process. A new alarm will re-start the dialer.
Note that if the user answered a call from the panel or called the panel during a dialing period
without Arming/Disarming/Stopping the dialer, the dialer will restart the cycle from the
beginning.
[7 #] - Check control panel status. The control panel will answer with an Armed or Disarmed
tune followed by an Alarm tune if it is in an alarm condition.
[7 and 7 #] - First Alarm Zone Report, beeps count for the zone number. Report user the first
zone that caused alarm. Arming or Disarming clears the First alarm zone reported by DTMF.
Zones 1 - 10: 1 to 10 short high tones
Zones 11 - 19: One long low beep for 10 followed by 1 to 9 short high beeps.
For example, zone 14: Reported as one long - low beep followed by 4 short beeps.
Zone 20: Two long - low beeps.
Zones 21 - 24: Two long - low beeps followed by 1 - 4 short high beeps.
[8X #] - Learn function. Using this command, the user can become familiar with the various
sounds used by the control panel in the remote access procedure. Further details find in the
dedicated paragraph. (X - The required sound).
[9 #] - End call. The control panel will sound a confirmation tune and will hang up.
20
SECTION III: LCD KEYPAD
1.1  Standard Keypad Functions
AV-GAD
ARMED
EASYLOADER AV-706
STATUS
SHUNT
Zone Failure
16 Av-Gad Lobb y
FIRE
Zone Description
Zone Number
Siren
1
Shunt
Display
2
Status
Delay
Delete
4
Chime
Test
7
Program
5
Telephon
*
Shunt
8
0
3
6
Reset
9
#
Keys function in text edit mode
Figure 7: AV-706 Keypad Layout
Common Terms in this Manual
 ‘SHUNT‘ and ‘BYPASS’ are interchangeable terms
 Program Mode - Enables features programming, ‘P’ is displayed, alarm is disabled
 Use Mode – System is disarmed and not in alarm or program mode
 AV-706, AV-707 or AV-707B are identical
 For code entry with LCD keypad press # (enter) to confirm


Standard Keypad functions are accessed by pressing keys (short press). The 1 to 0 keys used
for Arming/Disarming (ON/OFF), Zone Shunt (Bypass) and other programming
functions.
A short beep confirms each key press.
A short press on keypad key accesses the following special functions:
Chime
5
Instant Arming, by pressing key ‘5’ (requires programming).
Shunt
0
Zone Bypass, by pressing key ‘0,’ followed by entering the Zone numbers 01 to 32.
21
0
0 Group Bypass, press 0 and two presses on key ‘0.’ Groupthen
Bypass is operative only if System is armed within 60 seconds from the entry of this feature.
Yellow LED will flash and ‘h’ (Home) displayed for 1 second in confirmation.
Shunt
0
Shunt
Shunt
The AV-2008, AV-2016 Dublo version Group Bypass operates in different way:
Commands:
 0 & hold-down key 1 - Arm with group 1 bypass, or 0+0 - Group 1 Bypass
 0 & hold-down key 2 - Arm with group 2 bypass, or 0+0+0 - Group 2 Bypass
 0 & hold-down key 0- Arm with group 1+2 bypass, or 0+88 - Group 1+2 Bypass
Each command works as a toggle SET/CLEAR.
The AV-707B provides arming and group bypass by pressing one key (refer to keypad manual).
0 . Press key ‘0’ twice for Group Bypass. Operative only if system is
and
Armed within 20 seconds after entry of this feature. Yellow LED will flash; ‘h’ (Home) will be
displayed for 1 second in confirmation.
To activate Group Bypass II press key ‘0’ three times. To activate both group bypass groups,
press 0 then 88.
When Group Bypass is selected, the buzzer and LEDs react as follows:
 Shunt LED stops blinking 8 seconds after Arming, (prevents LED light from disturbing
sleepers near the keypad)
 There is no exit/entry delay-warning buzzer, and keys beep at the keypad.
 There are no ‘beeps’ at the keypad until an alarm occurs, or until Group Bypass is canceled.
 When the keypad LEDs are turned off after Arming (requires programming), touching the
keypad will turn them on for 5 seconds.
Shunt
0
Shunt
1.2  Hold-Down Functions


Holding down the key for approximately 2 seconds accesses hold-down functions
Hold down functions are confirmed by a long beep
Hold-Down Functions:
Siren
1
Shunt
Display
2
Status
3
Key 1  SIREN TEST
Key 2  SHUNT DISPLAY
Displays shunted zone(s).
Key 3  STATUS DISPLAY
Displays troubled or malfunctioning zone(s).
22
Delay
Delete
4
Chime
5
Telephone
Key 4  DELAY DELETE (INSTANT PROTECTION)
Cancels Entry delays in zones selected as ‘Delayed’ zones. All zones become
Instant.
‘d’ is displayed in confirmation. Instant Protection becomes effective only if System
is Armed within 20 seconds following hold-down of key 4.
Key 5  DOOR CHIME
Enables Chime when opening zone. Door Chime operates on Chime-programmed
zones. Hold-down key 5 enables and disables the function.
Chime mode is confirmed by ‘c’ display on keypad.
6
Key 6  DIALER TEST & FOLLOW-ME PROGRAMMING
Test is performed in ‘DISARMED’ mode.
Function
Displays Programmed Follow
Me Telephone Number Without
Dialing
Follow Me telephone number
programming
Programmed Telephone number
Verification (Display and Dial 4
telephone numbers)
Via AV-707 Series Keypad
Hold-down key [6]
Hold-down key [6] then holddown [6] again
Hold-down [6] then holddown [7], number not
displayed
Display programmed telephone numbers without dialing: Within few seconds, ‘c’ will appear on
the display, followed by the (programmed) ‘Follow Me’ telephone number.
When programming telephone numbers which require an inter-digit delay (‘Pause’) during
dialing; Hold-Down key [0], a momentary ‘P’ will be displayed (Delay duration is 3 seconds).
The ‘FOLLOW-ME’ number will be displayed, or displayed and dialed, followed by displayand-dial of up to three additional telephone numbers.
6
and Siren 1
Address 092 enables ‘Answer now‘ feature, the system answers
remote computer after one ring. This feature is important if the control panel programmed not to
answer incoming calls (programming of 21 rings or greater at address 091). To enable ‘Answer
Now’ feature program 01 at address 092.
Hold-down key 6 and then key 1, before the computer and modem connect (dial) the control
panel. The panel will acknowledge the command with two beeps and display an ‘A.’ The feature
remains active for 5 minutes after entered, enabling to remotely program (from remote
computer) the panel.
Other possibility to connect to a system connected on same line with a fax or answering machine
is to use the “Answer machine bypass” feature.
Telephone
23
Test






7
Key 7  FAULT FIND
Fault Find enables testing of all detection devices.
Fault Find mode is accessible only during 15 seconds following System Disarm.
24H, Fire or Panic alarm will stop Fault Find mode.
Hold down key 7.
Open and close each zone to test the zone regularity. A one-second beep confirms detection
of zone opening. Three beeps indicate zone closing.
Quit Fault Find mode by Arming the system.
Program
8
Reset
9
1.
2.
3
4.
5.
Key 8  PROGRAM
Key 8 accesses ‘Program’ mode and user code programming (followed by password)
Key 9  RESET. ‘Reset’ performs the following functions:
Cancels last Keypad entry
Stops the communication test (triggered by hold-down key 6)
Activates output 2 for resetting the Smoke Detector (requires programming)
Resets Day Zone Alarm at Keypad
Exits Programming mode (features, telephone numbers, etc.). To exit programming
mode enter 999 plus #
Key Zero Hold-Down functions
0 Key 0 Concise Alarm History: Hold down key ‘0’ to display the last alarm
1.
sequence.
Shunt
0 and
0 Detailed Events History (requires programming): Hold down key
2.
‘0’ and again hold down key ‘0’ to display up to 36 events, including: System opening and
closing by user number, opening or closing time, alarming zone and AC fail.
By holding-down key Shunt 0 twice, 3 LEDs start blinking, to indicate a special operation mode.
The events are displayed from the most recent event to the oldest.
Shunt
Shunt
24
Event
AV-707, 706 display
Time set
xx Time Set
Date set
xx Date Set
Installer programming
xx Installer Prg
User programming
xx User Program
Factory defaults
xx Fctry. Default
Communication (to CS) failure xx Comm. Failure
Panic from Panic zone
xx PANIC
Keypad locked (code error)
xx Keypad Locked
Low Battery
xx Low Battery
Table 1: Events as displayed at AV-2008, AV-2016 Dublo
Browsing through Events History
Keys used for browsing:
Shunt
Display 2
 Skip forward to next event
5  Display current event again
8  Skip backward to previous event
Reset 9
 Cancel History Event Mode and exit
Upon display of last event, if an attempt is made to move forward (key 2), a blank sign ‘-‘ is
displayed, along with a warning beep indicating that this is the last event. Press key 8 may to
move backward. If no key is pressed, Event History stops and system returns to Use mode.
When starting History Events mode the events are displayed from beginning to end without any
break, until any browsing key is pressed.
Chime
Program
During History Events, browsing system will respond only to alarm or panic, Arming
denied.
Alarm or Panic during History Event mode will quit this mode and system will set to Use
Mode (normal operation mode).
For easier detailed alarm history, use the downloaded from panel to remote computer. History
queue log of up to 250 events are displayed at panel keypad and in the EasyLoad PC software.
0 and
4.
Display and Setting of System Time: Hold down key ‘0’ and then
hold-down key ‘1,’ 3 LEDs will blink. Wait for the display of system time in 4-digit format.
To set new time, hold down key ‘0’ and then hold down key ‘1.’ Do not wait for time display;
enter the new time in 24-hour format. The local clock time is not stored in system memory;
clock must be adjusted after power-up. After powering-up system, time is reset to 00:00, ‘h’ will
be displayed to remind user to set time; ‘h’ will disappear after setting the time. If Auto-Arming
enabled the clock setting is form user Programming mode only, refer to Auto-Arming section.
Shunt
Siren
1
25
Shunt
Shunt 0
2
5.
and Display
Display and Setting of System Date: Hold down key ‘0’ and then
hold-down key ‘2’; 3 LEDs will blink. Enter date: ‘dd mm yy.’ The up and download PC
software displays time and date, along with event history.
The local date is stored in system memory; adjust date after long power-fail.
Years 00 through 77 translated as 2000 to 2077
0 and Status Concise History of Tampered Zones: Hold down key ‘0’ and then
5.
hold down key ‘3’ to display the Tampered zone alarm sequence.
New alarm will create a new history event instead of old one.
3
Shunt
Shunt
Delay
Delete
0
4
6.
and
Reset Events Memory (history): Not available.
Instead, during the installer-programming mode, clear history by command 200+04.
5
0 and
7.
Display Last 2 Users: Hold down key ‘0’ and then hold down key 5
to display user number and System opening or closing time.
‘o’ is displayed for Opening (Disarming); ‘c’ is displayed for Closing (Arming).
Chime
Shunt
0 Press (not hold-down) and press
8.
cancel all Bypassed Zones.
Shunt
*
Keypad Panic
Reset
9
(not hold-down), will display ‘-’ to
#
Keys  PANIC BUTTON
Holding down * and # keys will trigger Panic alarm. H will be displayed (zone ‘H’).
’
To cancel Hold-Down function accessed by keys [0], [6] and [7]; Hold-Down key 9 (Reset).
To quit zero hold-down functions, hold-down ‘9
1.3  Keypad Sounder
The Keypad sounder enhances the use of system operation and serves as a local alarm device
(requires programming).
The sounder emits sounds in the following instances:
OPERATION
SOUNDER RESPONSE
Pressing of any key
Short confirmation beep
Power up
Six beeps
Hold-down functions
Long confirmation beep
Faulty programming input
Long beep (+ ‘E’ display)
26
Delayed Zone triggering
Three long beeps
Exit delay starting (if programmed)
Warning beeps until the delay is over
Completion of Arm/Disarm
programming code
Programming Telephone numbers
One long confirmation beep
Completion of address programming
Two confirmation beeps
Pressing ‘Code 7’ for driving door
opening
Arming of System with Instant, Fire or
24H troubled zones
 Feature programming
Seven confirmation beeps
 Follow-Me number programming
Two confirmation beeps
During alarm (requires programming)
Intermittent beep until alarm reset
Two confirmation beeps
Five warning beeps + troubled zone
display
Two confirmation beeps
The buzzer of each keypad can be turned ON/OFF by holding down keys "0" and
"#"simultaneously. When the buzzer is ON, it will sound while the keys "0" and "#" are being
held down. When the buzzer is OFF, hold down the keys for 2-3 seconds, sounder feedback
heard in this case only after releasing the keys.
The buzzer set ON at "Power On" and every time the keypad is in programming mode.
1.4  LED Indicators
AV-705, AV-706 and AV-707 Keypads: Four LEDs provide visual indication of System status,
as well as confirmation of various modes.
Keypad LED’s indication
Armed LED-Red
Off
Blink slowly
ON steady
Blink fast
AV-2008, AV-2016 Dublo
System Disarmed
An alarm is triggered
System Armed
Mode does not exist
Status LED-Green
Off
Blink slowly
ON steady
Blink fast
AV-2008, AV-2016 Dublo
System Disarmed
Some zones are open
All zones OK
Some zones have been tampered
27
Shunt LED-Orange
ON steady
Blink slowly
Blink slowly
AV-2008, AV-2016 Dublo
Some zones are bypassed
Group bypass entered
8 seconds after Armed with
Group Bypass
Fire LED-Red
AV-2008, AV-2016 Dublo
Warning before Fire alarm
Blink slow
During and after Fire alarm
Blink fast
Note: At alarm time Troubled Zones are displayed at the Keypad.
 Red ARMED/ALARM Indicator - Lights up when system is armed, and blinks after an
alarm is triggered at any zone. Blinking indicates alarm history in memory.
 Green STATUS Indicator - Blinks when zone/s are troubled and remains lit as long as
zones are clear, rapid blinking during Tamper alarm.
 Yellow SHUNT (Bypass) Indicator - Lights up upon zone bypass.
(Note: may light automatically upon arming if Auto Bypass was programmed).
The indicator also lights up and blinks if a Group Bypass was entered by pressing ‘0’ twice.
 Red FIRE (Trouble) Indicator - Rapid blinking when a Fire Zone is troubled.
 Two LEDs Flashing (Left Most LEDs) - In user code programming mode, rapid blinking
indicates code or code index to be entered. In Installer programming mode, it indicates address
entry.
In Disarmed mode, the two left-most LEDs blinking + zone number display indicate 24H-alarm
mode.
 Three LEDs Flashing - In Disarmed mode, rapid blinking indicates AC power failure.
AC power fail event is displayed in Events. In Armed mode, rapid blinking indicates system
restored after AC Power Failure mode.
During programming Follow-Me Telephone Number, three flashing LEDs indicate to enter a
new telephone number.
 Four LEDs Flashing - Upon holding-down key ‘8,’ the system is ready for code to be
entered. (Same LED indication when code is expected for Bypass via code.)
1.5  Arm and Disarm System
1. Make sure that all burglary zones are closed.
2. The green Status LED indicator will remain lit (not blinking) while all zones are closed.
3. Green indicator will blink when a zone is troubled. Press key 3 for display of troubled zone
on keypad. An open delayed zone (exit zone) will also cause indicator to blink.
If instant zones or 24-Hour zones are troubled open zones will be displayed.
4. To bypass a zone, press key 0, followed by the zone number plus #, use two digits format.
28
5. Arming: Enter the Arm/Disarm code (No. 1 default code is 1,2,3,4), the Red Armed
indicator will light up. If any zone (not Delayed or Follower) is troubled,  will be displayed
and system will remain Disarmed.
System Arming is disabled if Instant zone troubled.
6. For Instant Arming, press key 5 (if previously programmed). See address 071.
Red ‘Armed’ indicator light up. The system is now armed.
7. Disarming: you may have to hold-down key 9 (reset) to clear any previous key presses, and
then enter arm/disarm code (or turn optional key-switch); the Red ‘Armed’ indicator will go
off.
Alarm history displayed upon disarming. If a 24H alarm occurs during Disarm mode Enter
Arm/Disarm code.
8. Keypad Keys Self Locking: In Armed and Disarmed mode, after six attempts to enter fault
code, the keys will not react to any key entry. This prevents code learning or other code
break exigency. After a 30 seconds delay, the keys will revert to code entry mode. Each new
erroneous code will lock system for another 30 seconds.
1.6  Auto Arming
Programming the time for Automatic Arming:
To set systems clock when Auto Arming enabled: Press 20 and enter the time in 24H format,
confirm with #. Press 20 and # to display the system clock.
To set Auto Arming Time: Press 21 and enter the time in 24H format, confirm with #. Press 21
and # to display the Auto Arming time.
Enter to user programming mode. Hold down '8' ('A' is displayed); type hour and minutes in 24
hours format. To display, hold down '8' and wait. To disable Automatic Arming program 0000.
After Automatic Arming is programmed, the system time can be set only via User Programming
Mode: Enter User Programming Mode (hold-down 8 and 1234), hold down '1' ('t' is displayed)
and type hour and minutes. Hold down key '1' and wait for the time display. Holding down keys
'0' then '1' (in use mode) to program the time is possible only if the Automatic Arming is
disabled (otherwise an 'Error’ warning is displayed). Those settings procedure at PRO and Dublo
panels are different; refer to the AV-706/7 keypad manual.
Automatic Arming will not operate if the system time has not been set (blinking 'h'). Automatic
Arming will not operate if the control panel is already armed.
Automatic Arming will operate even if the control panel is currently in alarm.
When the Automatic Arming programmed time arrives, the system starts at a 30-second
countdown. An 'A' is intermittently displayed and beeps are sounded at the keypad.
During the countdown period, to abort Automatic Arming enter a valid user code (not code No.
7, if used to ‘open’ a door).
29
SECTION IV: PROGRAMMING
1. SYSTEM CODES
Up to sixteen different Arm/Disarm codes and one installer (dealer) code are available; each code
consists of 1 to 6 digits.
Do not use ‘0’ as the first digit in a code.
Do not use ‘5’ as first digit in a code number if Instant Arming via key 5 was programmed.
User code must not start with the same numbers as the installer programming code (1994).
Do not use same codes or same first digit for different codes. For example if code No .1 is 1234,
programming code No. 2 cannot be 1256.
1. Default Arming and Disarming Code ‘1 2 3 4’ (Code No. 1) - Use ‘1234’ as Arming
Code (also called Owner Code). Use code No. 1 to program a new user code.
Upon setting new Arming & Disarming code, default user code ‘1234’ automatically replaced.
For setting default codes, Power up by applying AC and battery and immediately
Press both
2.
3.
4.
5.
6.
# after 2nd beep, release keys, ‘U’
* together
(during 20 seconds) hold-down keys
displayed three times in confirmation. To set codes to default during programming; in address,
200 enter 05, all codes will restore to default.
Code number 7 for access control (requires programming) - Arm/Disarm code No. 7
activates the SLO (Selective Output) output, which is used for such functions as opening an
electric lock.
Code number 7 is operative during both, ARM and DISARM modes, confirmed by seven
short beeps. Code 7 drives the SLO output as ‘Momentary’ output.
Pulse duration is 5 seconds.
Code number 8 as Visitor Code (requires programming) - Arm/Disarm code No. 8 is for
‘one time code’ (employees and one-time visitors). This code is valid for 30 seconds from
Arming. After 30 seconds, the code is rendered as invalid.
Entering code 8 will delete zone bypasses, including auto-bypass.
Code number ‘9’, Programming Code (Installer Code) - Code No. 9 enables entering the
programming mode (system features programming) at the Installer level.
The factory default programming code is ‘1 9 9 4.’
The programming code may be installer-programmed. Installer code does not Arm or Disarm
system.
User Codes - (Arming and Disarming code). Each code consists of 1 to 6 digits. System
provides eight user programmable codes.
Key Visual Feedback - Visual ‘feedback’ from the keypad display upon entering of code.
This feature indicates the code entry progress and is most practical when the keypad buzzer is
disabled at Group Bypass mode, or if selected by programming. Entry of code by user or
installer is confirmed at keypad display. Display segments will light up clockwise, indicating
the sequence of the digits entered.
Typing six erroneous codes will lock the keypad keys for 30 seconds
30
1.1  User Code Programming via AV-706, AV-707
Set New User Code
User Programming
8
1. Hold down key
2. While the four LEDs are blinking, enter code No. 1 (default 1 2 3 4)
3. If code is valid, “User Programming” displayed
4. The 2 left-most LEDs blink to indicate that the system is waiting for a new user code index
(user 01 to 16) to be entered
5. Enter the code index (01 for code No. 1; 02 for code No. 2, etc.)
6. The 3 right-most LEDs blink to indicate that the system is waiting for a new code (1 to 6 digits)
to be entered. The code is voided if user code not entered.
7. Enter the new code; new code and user index is displayed for confirmation. If during 60
seconds data not entered system automatically escape from code setting.
8. To quit code setting press ‘99’ plus #.
Program
Set new Installer Program Code
8 , while the four LEDs are blinking, enter 1994 (default code) plus #.
1. Hold down key
“Installer Progr.” displayed, 2 left-most LEDs blinking.
2. While system is in installer program mode, enter address 099, Installer Code displayed 1 9 9 4
3. Enter 099, than the new code plus #
4. New code displayed for conformation. System revert to Installer Programming mode.
5. Enter 999 plus # to exit
Program
Delete a User Code
8
1. Hold down key
2. While four LEDs are blinking, enter code No. 1 (default 1 2 3 4)
3. To erase an existing code: Enter user index number (01, 02, 03....), Hold Down simultaneously
the '*' and ' #' keys, followed by #, E (erased) will be displayed.
The Master (code number 01) cannot be erased.
Program
5 is a programmable feature, which may cause erroneous
Instant Arming by key number
Arming. It is recommended to disable this feature. Do not to use 5 or 0 as the 1st digit of the code
Chime
31
2. FEATURE PROGRAMMING AT INSTALLER LEVEL
2.1  Programming Table AV-2008, AV-2016 Dublo (V 3.05)
1) ZONE 1 to 16 FEATURES
Zone Number 
Feature 
Zone In Use
Entry/Exit Delay 1
Entry/Exit Delay 2
Entry / Exit Follower
24-Hour Zone
Fire zone
Day Zone
Green Zone
Swinger Shut-Down
Chime
EOL Resistor Zone
Enable Tamper Zone
Delayed Power-Up
Fast Response
Group Bypass
Group Bypass II
Manual Bypass
Siren Out
Alarm 1 Output
Alarm 2 Output (only 2016)
SLO output 2
Dial on Alarm
Keypad sounder on Alarm
Normally Open (N.O.)
Panic Zone
1
Add.
100
104
108
112
116
120
124
128
132
136
140
144
148
152
156
160
164
168
172
176
180
184
188
192
196
4 5 6
Group 1
3 4 5 6
7
8
2
3
4
5
6
7
8
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
7
7
7
8
8
8
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
1
1
2
2
3
7
8
2
1
1
9
Add.
101
105
109
113
117
121
125
129
133
137
141
145
149
153
157
161
165
169
173
177
181
185
189
193
197
ZONE 17 to 32 FEATURES
Zone Number 
17 18 19 20 21 22 23 24
Feature 
Add.
Add.
Group 3
Zone In Use
102
103
Entry/Exit Delay 1
106
107
Entry/Exit Delay 2
110
111
Entry / Exit Follower
114
115
24-Hour Zone
118
119
Fire zone
122
123
Day Zone
126
127
Green Zone
130
1 2 3 4 5 6 7 8
131
Swinger Shut-Down
134
135
Chime
138
139
EOL Resistor Zone
142
143
Enable Tamper Zone
146
147
Delayed Power-Up
150
151
Fast Response
154
155
Group Bypass
158
159
Group Bypass II
162
163
Manual Bypass
166
1 2 3 4 5 6 7 8
167
Siren Out
170
1 2 3 4 5 6 7 8
171
Alarm 1 Output
174
1 2 3 4 5 6 7 8
175
178
179
Alarm 2 Output (only 2016)
SLO output 2
182
183
Dial on Alarm
186
1 2 3 4 5 6 7 8
187
Keypad sounder on Alarm
190
1 2 3 4 5 6 7 8
191
Normally Open (N.O.)
194
195
Panic Zone
198
199
2 SLO is a non-timed output. SLO = Selective Output.
Factory Default Program is as shown in table; Blank Square means no default program
32
1
10 11 12 13 14 15 16
Group 2
2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
7
7
7
8
8
8
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
25 26 27 28 29 30 31 32
Group 4
1
2
3
4
5
6
7
8
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
7
7
7
8
8
8
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
2) TELEPHONES, SIGNAL TEST TIME
Tel. 1
Tel. 2
Tel. 3
Tel. 4
010
011
012
013
Test Signal Time
Address 
Time 
Tel. 1 is ‘Follow Me’. Tel. 2 and 3 are communicator option. Tel. 4 is Dialer.
(According to programming). Maximum 16 digits + 4 pauses each Tel. Number.
Auto Arm Time
014
016
(00:01)
00:00
Test signal to central station. Codes define at
address. 237 & 255. Enter time in 24 hour format
NB: Press and hold the ‘9’ key until the keypad beeps, after the address to erase telephone numbers.
To insert * in the phone number: Enter to program mode, program system to dial in DTMF, Hold-down keys # and * (as panic), ‘A’ will be displayed.
To enter Pause during dialing hold-down key ‘0’.
3) OUTPUTS and TIME-OUTS
Ac Fail
Rpt Delay
Minutes
058
1
0
Entry
Delay 1
Sec's
060
1
2
Entry
Delay 2
Sec's x 4
061
0
0
Exit
Delay
Sec's x 4
062
0
8
Siren
Time
Minutes
063
0
4
ON Siren
Time
Sec's
064
1
5
OFF Siren
Time
Sec's
065
0
4
A1
Time
Sec's
066
3
0
Reserved
******
067
0
4
Chime
Time
Beeps
068
0
3
Abort
Delay
Sec's
069
0
4
4) SYSTEM FEATURES
Feature
Enable-Siren/Bell Test upon Arming
Enable-3 Beeps upon Disarming
Enable-Buzzer upon Entry Delay
Reserved
Disable-4 LEDs display during Armed
Enable-Battery Test upon Arming
Enable-Code No. 7 for Access Control 1
Enable-Keypad Panic
070
1
(2)
(3)
(4)
5
(6)
7
(8)
Feature
Enable-Erase F. Me number on Disarm
Enable-Instant Arming via Key 5
Enable-SLO 1 as reset for smoke detector
Enable-Display Troubled/Open Zone
Enable-Manual Bypass via Code No. 1
Lock in Armed after Tamper Alarm
Enable-Momentary Key-Switch
Enable-Code ‘8’ as one time code
071
1
2
3
4
5
6
(7)
8
Feature
Enable-Bell mode
Enable-Detailed alarm history
Enable-Report Opening/Closing
Enable-ON output as for AV-03 line cut
Enable-Report bypassed zones at Arming
Enable-Exit delay when delayed zones clear
Enable-’ON’ output as SVM trigger
Enable-Codes reset to default by hold *& #
072
(1)
(2)
(3)
4
5
6
7
(8)
Feature
Reserved
Enable-Test to central station each hour
Enable-Self contain Bell (0V at alarm) **
Enable-Buzzer upon exit delay
Enable- Group Bypass when Armed by Key
Enable- 2 Siren Beeps at Disarming by Key
Enable – A1 output follows Siren time
Enable – Inverting of Outputs polarity
073
1
2
3
4
5
6
(7)
8
Keypad Panic Alarm
Siren on Panic
Alarm 1 On Panic
Alarm 2 On Panic
SLO On Panic
Telephone Report
Buzzer alarm on Panic
Enable Emergency Buttons
Reserved
074
1
2
3
(4)
(5)
6
7
8
Tamper Alarm
Tamper zone 24H zone
Alarm 1 on Tamper
Alarm 2 On Tamper
SLO on Tamper
2nd Aux. Key at last zone on the board
Tel. Line test at Disarmed Mode
Activate SLO at Tel. Line fail
Dialer reports on AC fail
075
1
2
3
4
5
6
7
8
*
Feature
076
Feature
Enable -’SLO1’ output for SVM trigger
1
Enable K”P and Siren sounds at home mode
Enable – Remote A1 activation by DTMF
2
Auto Reset before alarm time out
3
Enable – Alarm panel DTMF control
(4)
Enable – Sounder for Tel. line fault
5
Enable – Siren for tel. line fault
6
Enable - Bypass Answering Machine
7
Enable-Echo Cancellation Tone (AUSTEL)
8
1
- Code No. 7 for access control drives SLO 1 output ** Self-contained Bell is operative if Bell mode selected
*** Available in AV-2008, AV-2016 Dublo. In Australia program ‘8’ in address 076.
* Those features cannot be enabled at the same time.
078
1
2
3
4
5
6
7
8
Address 077, CS test day: 1 - Sun 2 – Mon, 3 – Tues, 4 – Wed., 5 – Thu., 6 – Fri., 7 – Sat., 8 - All week's days, 0 – Clear all
33
*
***
5) DIAL AND MODEM PARAMETERS
PreDial
Delay
Wait
for
Dial
Tone
AntiJam
Delay
Sec's
Sec's
Sec's
080
0
081
2
0
082
4
1
0
Dial
tone
detection
Dial
Mode
Tel.
MSG
Time
InterCall
Delay
ReDial
Cycle
s
(max.
)
Pulse
Make
Pulse
Break
Inter
Digit
Delay
00 = No 0= Pulses Sec's
01 = Yes 1= DTMF
083
084
085
0
1
0
1
5
0
Sec's
XX Cycle
5 mS
5 mS
50 mS Tel. Rings 00 = No
01 = Yes
090
091
092
2
0
1
0
0
1
2
086
0
0
087
3
088
0
089
8
1
2
Rings
qut'y
for
mode
m
Instant
mode
m
answer
MODEM PARAMETERS
Rings
before
Answer
Answer
Now
(Modem)
Reserved
Min.
Ring
Length
Min.
Ring
Cycle
Tel. Line
Test
Intervals
Ring
Time out
Rings
00 = No
01 = Yes
092
0
1
*****
10 m’S
(10-20)
094
1
5
100 m’S
(7-25)
095
1
5
Minutes
(Max 99)
096
0
0
Seconds
(4-35)
097
0
6
091
1
0
093
1
9
Note address 091: The download is ENABLED by default. Enter a value of 21 at address 091 to disable modem (21 rings for
modem not accepted by telephone net). To ENABLE enter 01 to 20 at address 091. To enable Instant Modem Answer function
(Answer Now), hold-down key 6 then hold-down key 1. ‘A’ displayed in confirmation.
6) USER CODES SETTING Address 099 provides setting of user codes 01 to 17
USER 01
1,2,3,4
USER 09
USER 02
USER 03
USER 04
099
USER 05
USER 06
USER 07
USER 0 8
USER 10
USER 11
USER 12
USER 13
USER 14
USER 15
USER 16
Installer Code
USER 17
1,9,9,4
For programming End-User codes 1 to 17 (Arm/Disarm & Programming codes) via installer programming mode; enter to
address No. 099, then program new codes by first entering the code index (01, 02, 03..). User 1 code is the Master code (for
changing codes), user 17 code is the programming code - If changed code 1 or 17 make a note of the new codes.
To erase a code does not enter any digit after the code index number.
To send the Force Opening Code (Ambush) the user should enter the Disarming code in reverse order.
7) FACTORY DEFAULT SETTING: Enter 6 9 in address 200, to revert to factory default programming
8) COMMUNICATOR PARAMETERS
TELEPHONE
Receiver
Format
021
No. 2
0
TELEPHONE
Handshake
Frequency
023
0
Receiver
Format
0
0

0
0
0
0
0
Protocol
Type
026
2

027
0
Data
Format
024
0
Protocol
Type
025
2
Handshake
Frequency
022
No. 3
Data
Format
028
0

0
0

Check
Sum
(Parity)
029
Transmit
Rounds
0
0
0
031
0
Sum
Check
(Parity)
030
Transmit
Rounds
0
0
0

032
0

Inter Rnd
Delay
Time
033
3
0
Inter Rnd
Delay
Time
034
3
0

Wait for
Handshake
Time
035
2
0
Wait for
Handshake
Time
036
2
0

00=1400 Hz 00=3 X 1 00=Standard
00=None
00=2 Rnd
00=0.1 Sec
XX=Sec's
00 - Dialer only (No Communicator)
01 - Ademco, Silent Knight Slow,
01=2300 Hz 01=4 X 1
01=Extend 01=S.Check
01=1 Rnd
30=3 Sec
Scantronic
02 - Radionics Fast
02=Hi/Low
3 Sec's is
03 - Sescoa, Vertex, DCI, Franklin
02=4 X 2
Default
04 - Silent Knight Fast
02=Hi/Low
05 - Radionics, DCI, Franklin Slow
03=3 X 2
06 - Universal High Speed
**
07 - Contact ID/Ademco Fast*
00 - ‘No Communicator,’ is identical to ‘Dialer’ that generates sound upon alarm. ** For Contact ID, program 07 in 021 & 022 address.
* For Ademco Fast Receiver type 685 enter 02 at address 023 & 024.
34
11) SELECT ZONES FOR PARTITION (Partition No. 01 is by default zone 1 to 32)
Zone Number 
Partition 
Partition 01
Partition 02
Partition 03
Partition 04
Partition 05
Partition 06
Partition 07
Partition 08
Add.
500
504
508
512
516
520
524
528
Zone Number
Partition 
Partition 01
Partition 02
Partition 03
Partition 04
Partition 05
Partition 06
Partition 07
Partition 08
Add.
502
506
510
514
518
522
526
530
1
1
2
2
3
4 5 6
Group 1
3 4 5 6
7
8
7
8
17 18 19 20 21 22 23 24
Group 1
1 2 3 4 5 6 7 8
9
Add.
501
505
509
513
517
521
525
529
Add.
503
507
511
515
519
523
527
531
1
10 11 12 13 14 15 16
Group 2
2 3 4 5 6 7 8
25 26 27 28 29 3
Group 2
1 2 3 4 5 6
31 32
7
8
12) SELECT USERS FOR EACH PARTITION.
Maximum 8 partitions. (By default Users 01 to 16 are linked Partition No. 01). Partition number should be entered in 2 digits.
1
-
Group 1
Group 2
Partition
User 1-8
Partition
User 9-16
2
3
4
5
6
7
8
533 534 535 536 537 538 539
01 01 01 01 01 01 01
USER
ADDRESS
 PARTITION 
9 10 11 12 13 14 15 16
540 541 542 543 544 545 546 547
01 01 01 01 01 01 01 01
UNDER BUILDING ON 13) AUTOMATIC ARM AND DISARM TIMERS
Auto Arm
Time
(00:01)
550
Enable = 01
Disabled = 00
00
582
Auto Disarm
Time
(00:01)
566
Enable = 01
Disabled = 00
00
590
Partition
Number
01
598
Cycle 2
Address
(00:01)
552
00
583
(00:01)
568
00
591
01
599
Cycle 3
Address
(00:01)
554
00
584
(00:01)
570
00
592
01
600
Cycle 4
Address
(00:01)
556
00
585
(00:01)
572
00
593
01
601
Cycle 5
Address
(00:01)
558
00
586
(00:01)
574
00
594
01
602
Cycle 6
Address
(00:01)
560
00
587
(00:01)
578
00
595
01
603
Cycle 7
Address
(00:01)
562
00
588
(00:01)
574
00
596
01
604
Cycle 8
Address
(00:01)
564
00
588
(00:01)
580
00
597
01
605
AUTO ARM &
DISARM CYCLE
Cycle 1
Address
Enter time in 24-hour format.
35
14) TEL. 2 COMMUNICATOR - SUBSCRIBER ID CODES
Note: For subscriber ID that contains a ‘0’ (zero), enter 10 in place of 0. ‘0’ will be displayed as ‘A.’ Do not enter 0 0.
Group 1
Group 2
Group 3
Group 4
Group 5
Users 1-9
Users 9-16
Alarm / Restore
ID
Alarm / Restore
ID
Alarm / Restore
ID
Alarm / Restore
ID
Alarm / Restore
ID
Opening/Closing
ID
Opening/Closing
ID
610 611 612 613 618 619 620 621 626 627 628 629 634 635 636 637 642 643 644 645 650 651 652 653 658 659 660 661
EASY PROGRAMMING - TEL. 2 COMMUNICATOR - SUBSCRIBER ID CODES
Group 1
Group 2
Group 3
EASY Program
EASY Program
EASY Program
Alarm / Restore ID Alarm / Restore ID Alarm / Restore ID
710
718
726
Group 4
Group 5
Users 1-9
Users 9-16
EASY Program
EASY Program
EASY Program
EASY Program
Alarm / Restore ID Alarm / Restore ID Open. / Closing ID Open. / Closing ID
734
742
750
758
To program the subscriber ID number more easily (as a sequence of 4 digits), use the EASY.
Even if your code is only three digits, you must still enter four digits. The 4th digit can be any digit, and the system will disregard the 4th
digit.
TEL. 3 COMMUNICATOR - SUBSCRIBER ID CODES
Group 1
Group 2
Group 3
Alarm / Restore ID Alarm / Restore ID Alarm / Restore ID
Group 4
Group 5
Users 1-9
Users 9-16
Alarm / Restore ID Alarm / Restore ID Opening/Closing ID Opening/Closing ID
614 615 616 617 622 623 624 625 630 631 632 633 638 639 640 641 646 647 648 649 654 655 656 657 662 663 664 665
EASY PROGRAMMING - TEL. 3 COMMUNICATOR - SUBSCRIBER ID CODES
Group 1
Group 2
Group 3
EASY Program
EASY Program
EASY Program
Alarm / Restore ID Alarm / Restore ID Alarm / Restore ID
714
722
730
Group 4
Group 5
Users 1-9
Users 9-16
EASY Program
EASY Program
EASY Program
EASY Program
Alarm / Restore ID Alarm / Restore ID Open. / Closing ID Open. / Closing ID
738
746
754
762
To program the subscriber ID number more easily (as a sequence of 4 digits), use the EASY Program (available only from VER 1.04 and up).
Even if your code is only three digits, you must still enter four digits. The 4th digit can be any digit, and the system will disregard the 4th
digit.
Values beneath addresses are default programming.
Address - a location on the programming sheet.
AV-2008, AV-2016 Dublo addresses reside between 003 and 762.
Value - determines the characteristics of an address.
36
2.2  Introduction



The program determines most of the control panel features. Programming is performed in
order to enable maximum compatibility of the control panel with the specific site.
The control panel is supplied with the basic ‘Factory Default Program,’ which is in effect at
system power up. (See also: Factory defaults programming.). Factory default setting:
Enter 6 9 in address 200, to revert to factory default programming.
Before starting programming, mark the desired values on the programming sheet.
2.3  Programming Sheet Explanation
Table 1: Enter the zone feature by zone number, as described in addresses 100 to 191.
Table 2: Addresses 010 to 013 used to enter the telephone numbers that dialed upon alarm or at
other events (when communicator to central station has been programmed).
Telephone numbers 2 & 3 are for communicator (if selected), or non-communicator, according to
programming of addresses 021 & 022. Telephone numbers 1 & 4 are only for regular telephone
dialer with sound alarm.
Table 3: Addresses 060 to 069 indicate the times out. Enter the time in two digits. (e.g. for two
seconds, enter 0 and then 2).
Address 074 and 075 manage five different features that specify the alarm outputs upon Panic and
Tamper alarm.
Note: entering a ‘0’ value at address 074 or 075 will delete all four-alarm outputs during Panic or
Tamper alarm at that address zone.
Table 4: Addresses 070 to 072 indicate special features of the system. Enter the required features
by their number in each address. Each address contains 8 different parameters.
Table 5: Addresses 080 to 092 indicate telephone specifications according to local telephone
company requirements. Address 091 and 092 sets the up and download modem.
Table 6: Address 099 provides setting of user codes 1 to 17 within the programming mode.
Table 7: Address 200 reverts system to factory default by entering 69. Entering 77 in address 200
sets panel to local up and download.
Table 8: Addresses 021 to 036 sets the communicator parameters according to your central
station's specifications. Contact the central station for full details.
Table 9: Addresses 040 to 054 provides selection of the required events to be reported. For
example, to select zones 1,2 and 6 for Zone Restore report program 1,2 and 6 in address 045. Do
not program if Contact ID format selected.
Table 11: NOT OPERATIVE YET (marked with cross lines). Addresses 500 to 531 provides to set
the required zone for each partition. The default is zone 1-32 to be in partition No. 01.
Table 12: NOT OPERATIVE YET (marked with cross lines). Addresses 532 to 547 provides to set
the required users for each partition. The default is users 1 to 16 to Arm and Disarm partition No.
01.
Table 13: NOT OPERATIVE YET (marked with cross lines). Addresses 550 to 605 the time set
for each timer, and selects which partition will be Armed and Disarmed at this time. Each
automatic Arming or Disarming can enabled or disabled.
Table 14: Addresses 610 to 762 contains the communicator Subscriber ID Code transmitted to the
central station. Follow EASY program instructions for fast subscriber ID codes programming.
Programming Mode automatic timeout is three minutes for user programming mode and
fifteen minutes for installer programming mode
38
2.4  Glossary of Programmable Features
Note! A zone not programmed as a 24H, Delayed, Fire or Follower zone, is automatically
acknowledged as an Instant zone
24-Hour Zone - Zone programmed for 24-hours protection. Alarm sounded in both Armed and
Disarmed modes, indicated by Armed LED blinking. If 24H zone remains troubled after disarming
the system a warning buzzer will sound after 10 seconds (allows the user to repair or bypass the
troubled zone) from disarming. After another 10 seconds, alarm is on.
Address: 116-119.
Abort Report (to CS) - If the system disarmed during the "abort delay" there will be no report to
central station. Events during this period recorded in history. Address: 069
Answering machine bypass - In case the alarm panel is connected with fax or answering machine
on the same line, this feature provide to connect to the control panel for up and download. If this
feature is not enabled the fax or answering machine answers before the panel, connection is
impossible. Program at least 20 seconds at address 097 (ring time out), Program 7 at address 076.
Code ‘8’ as One Time Code - This feature enables user code no. 8 as one time Arming code.
When this feature selected, the code will be operative during 30 seconds after Arming with code 8.
During the 30 seconds, Code No. 8 will be active for both Arming and Disarming. Enter ‘8’ at
address 071 to enable this feature.
Day Zone - A zone programmed as a Day Zone enables alarm from keypad's buzzer during
daytime (system is usually disarmed). The day zone will trigger the keypad sounder and the zone
number will flash on keypad display. To reset Day Zone alarm, hold-down key 9 (reset key).
During Arm mode, this zone will act as burglary zone and will sound an alarm when troubled.
Address: 124-127.
Delayed Zone - A zone programmed as a Delay Zone provides exit and entry delay time from
moment of arming. See Entry Delay 1 and 2.
Dial Parameters - Enables adjustment of dialing specifications according to local requirements.
The most critical are the Pulse Make and Pulse Break times (Pulse Dial mode), which may be
different in each area. Steps are by 5 milliseconds (ms), which is sufficient according to tolerance
requirements of +/- 2 milliseconds. Contact the local Telephone Company for full specifications in
your area. Addresses: 080-096.
Enable Siren Test upon Arming - Short beep sound for siren test upon arming, indicating that
the system armed and siren is OK. To enable this feature (Siren Test upon Arming), enter value
‘1’ in address 070.
39
Enable SLO 1 for Smoke Detector Reset - After the smoke alarm is triggered, reset is required.
Pressing key ‘9’ activates SLO 1, which shortly disconnects smoke detector power (via optional
relay) and resets automatically. Address: 071- 3.
Entry Delay 1 and 2 - To enable two different entry delay periods, program-selected zone(s) for
Entry Delay 1, and other zones for Entry Delay 2. To cancel entry delay, hold - down key 4 before
Arming.
Entry Delay 1 maximum delay time is 99 seconds, and Entry Delay 2, up to 396 seconds (see
addresses 060 and 061).
Addresses: 104, 106, 108, 110.
Entry/Exit Follower Zone - Reacts instantly upon detection without previous triggering of
delayed zone. Exit delay affects follower zones. Follower zone acts as delayed zone during exit
delay and after entering via delayed zone. Try to avoid installing magnetic switches for protection
of a follower zone. (Use magnetic switch in delayed zone only for entry/exit door).
Address: 112-115.
Erase ‘Follow-Me‘ Number upon Disarming - After disarming the system, the Follow-Me
number is deleted. If ‘Erase’ feature is not programmed, the ‘Follow-Me’ number will be stored in
the system memory as the first Dialer number.
Address: 071-1.
Exit Delay - Determines the delay period (for delayed or follower zones) before zone becomes
active. Countdown starts upon system arming. Maximum exit delay is 396 seconds.
Address: 062.
Exit Delay when Delayed Zones Clear - Enables system Arming only when all delayed zones are
clear. Exit Delay will start the countdown. Applicable when long or variable exit delay is required.
Address: 072.
Fire Zone - Zone programmed for connection of fire or smoke detector. Alarm sounded in both
Armed and Disarmed modes. Activate the Fire LED. If Fire zone remains troubled after disarming
the system a warning buzzer will sound after 10 seconds from disarming (allows the user to repair
or bypass the troubled zone). After another 10 seconds, the alarm is on.
The siren sounds different at 24H zone alarm (not same as burglary alarm).
Address: 120-123.
Fast Response Zone - Fast Response time of 100 ms (standard response time is 750 ms).
Use Fast Response zone for connection of shock (inertia) or beam type detectors. The response
time for zones programmed as ‘fast Response’ is not adjustable in AV-2008, AV-2016 Dublo.
Note: Applicable for very short open time contacts. Warning: Fast response zones increase the
probability of false alarms. Addresses: 152-155.
40
‘Follow-Me’ Number - Telephone number programmed by user before Arming, enables user to
program a telephone number that will call (follow) him at the locations he go to in case of alarm.
Addresses: 010.
Forced Opening (Ambush) - Forced Opening (disarming) is operative only if ‘Report to Central
Station’ is selected (refer to program table address 256). By disarming the system with the
opposite sequence, code (arming with 1234 code, and disarming with 4321 code) the system will
report a forced opening (forced Disarming).
Group Bypass (Home Mode) - Group Bypass enables removal of several zones from the system.
The group of zones to be bypassed (shunt) is programmable. Refer to address 156-161, 158-163.
To activated Group Bypass is press key ‘0’ twice before arming the system, and is effective only if
system is armed within 20 seconds of ‘Group Bypass’ entry. There are two bypassed groups. AV707B keypad enables arming and group bypassing by one key entry.
Upon Group Bypass activation, the Yellow LED flashes, and ‘h’ (Home) is displayed for 1
second.
Green Reset Zone - This feature disables zones in alarm to keep alarming as long as the zone is
troubled. Useful in case of wire cut, broken sensor, etc. In such case, the zone will alarm one siren
cycle and will alarm again only after zone cleared and troubled again.
Green Reset Zone required by the environment authorities to keep the alarm noise as short as
possible. Zones programmed as a ‘Green Reset Zone,’ will not signal another alarm if the zones
remain troubled.
Address: 128-131.
Inter Call Delay - Time delay until dialer proceeds to next telephone number.
Address: 086. (Recommended and default value: 20)
Instant Arming - For instant arming press key ‘5.’
It is recommended to disable this feature if keypad is too easily accessible.
Address: 071-2.
Keypad Sounder on Alarm - This feature enables keypad sounder during alarm. When alarm is
on, a modulated tone will sound until disarming of the system.
Address: 188, 189, 190, 191.
Lock in Arm after Tamper Alarm - Not operative with PRO and Dublo. Addresses: 071.
Manual Bypass (Manual Shunt) - Any zone (1 to 32), selected as Selective Bypass, maybe
bypassed (removed from the system) by pressing key ‘0’ and then the zone number. The Yellow
LED will light up in confirmation. It is not possible to bypass all zones. Upon Disarming, all
bypassed zones will automatically become non-bypassed.
41
EOL Resistor Zone - Programmed zone(s), wired with an End of Line resistor, will be activated
upon opening the loop between the zone and common (-). Shorting the resistor cause Tamper
Alarm. Address: 140-143.
‘Off’ Siren Time - Determines silent period during an alarm cycle. This feature helps prevent
over-heating of sirens and electronic components and prevent noise. Required against noise
pollution by environmental authorities. (Recommended default value: 04).
Address: 065.
‘On’ Siren Time - Determines siren sounding period during the alarm cycle.
Programming a value of ‘0’ will render audible in all types of zones.
(Recommended and default value: 15).
Address: 064.
Outputs Deliver High at Alarm - If programmed during alarm, the A1, ON, SLO outputs will
deliver High (drives Low when disabled) at alarm. This feature is most applicable for driving
wireless central station RF transmitters or other devices requiring High (max. 100 mA) when
triggered. If another feature is selected for the same output, this feature will be canceled.
Normally Open Zones – Zone defined as Normally Open cause alarm when the zone is connected
to –V. The N.O. relay in alarm will cause a SHORT condition, which will trigger the alarm.
Sensor with Normally Open (N.O.) relay can be wired without EOL resistor. If several N.O.
devices are used, wire them in parallel. If N.O. feature is not programmed, N.O. devices, such as
push-button, should be wired in parallel to the EOL resistor.
Address: 192-195.
Programming Code – The programming code provides access to the Installer Programming
mode.
To program is possible if the current Programming Code is known.
Default programming code is ‘1 9 9 4.’
Panic Alarm - Holding down * and # keys will trigger Keypad Panic alarm; H is displayed (zone
‘H’).
To reset the alarm enter a valid code. Panic Zone included at address 196-199, the default is 0.
The Panic zone provides to use remote panic buttons. When AV-707B keypad is interfaced Panic,
Medical and fire button are included, to enable them program at 074 a 7.
Contact ID format reports Panic, Medical and Fire alarm to central station. Siren sounds: If Siren
(not Bell) in use, the sound is different, not the same sound as Burglary alarm. Panic alarm
recorded in history, in LED keypad displayed as H (z). (Z: Zone number, 1-32). For Silent Panic
alarm, remove siren and buzzer activation by programming the Panic Zone so. Address: 196-199.
Re-Dial Cycles - The number of times dialer or communicator will dial the programmed
telephone numbers. Address: 087. (Recommended value: 3)
42
Report Opening/Closing (Enable-Disable) - This feature enables or disables the Opening and
Closing report for central station. Applicable for residential installation when Opening and
Closing reports are not required. Address: 072.
Report Bypassed Zones at Arming (Enable-Disable)- Insurance companies require this feature
in certain areas. Address: 072.
Siren Time - Determines the duration of the alarm when zones are activated. Fire and Panic alarm
issues a modulated 2-tone siren. 24H and Burglary alarm issues a modulated 3-tone siren.
Modulated tones are disabled when Bell Mode is programmed (Address 072).
A programmed value of ‘0’ will issue an inaudible alarm. Address: 063.
Swinger Shut-Down Zone - Zones 1 to 32 which have been programmed as Swinger Shut-Down
zones will reset twice (3 alarm cycles). This feature prevents repeated false alarms and lowers the
security level. Address: 132, 133, 134,135.
SVM (Synthesized Voice Module) Module - Optional module that enables transmission of
recorded message upon alarm. Special interface is requires connecting the SVM module. To
trigger the SVM unit, program address 072, location 7. SVM pack contains the wiring
instructions.
Signal Test to Central Station (Enable-Disable) - This feature enables setting up time of signal
test, which is transmitted by the communicator at the required time. The time is set at address 014
in a 24-hour format. Test performed 1 minute after: Powering-up, disarm, programming exit.
For example: If the transmitting time is every night at midnight, enter 0000. To enable the signal
test, program ‘4’ at address 072.
Address 073 ‘2’ enables the signal test every hour. Other periodical or manual via keypad, CS
tests are not possible. (CS is shortening of Central station).
The test signal is on automatically every 24 hours to confirm that system is operative.
The system status (Armed or Disarmed) reported also if extended, or if two-digit format selected.
For example: ‘A’ in address 236 for Armed, and ‘D’ in address 254 for Disarmed.
Signal Test enabled by days of the week programmed at address 077. As 1 is Sunday, 7 is
Saturday. An eight (8) enable test for all the week days, 0 clear all.
Even if the test programmed at each hour, it will perform only on the programmed days.
Address: 072, 073, 077, 236, 237, 254 and 255.
Telephone Line Monitor - Telephone line test will begin six seconds after power-up or arming.
If address 083 (dial tone detection) is programmed as 0 (zero), the telephone line test will not be
performed. By selecting the test Abort Delay forced 00 at 069.
Address 096: Time interval between telephone line tests range 00 to 99 minutes.
If ‘00’ is selected no test performed, but failure to get a dial tone when dialing will cause a
"Phone line fault" event (recorded in history events). To test the telephone line when the panel is
Disarmed, program 075 – 6, see also 075-7.
43
Zone In Use - A zone programmed as an ‘In Use Zone’ enables activation of the programmed
zone. This feature eliminates the need to bypass zones by wire or End of Line Resistor.
Address: 100-103.
2.7  Step - By - Step Programming
Entering Installer (Engineer) Programming Mode Via AV-706 or AV-707 Keypad
Easy Tip: You may program any address by entering the address, followed by the value in
sequence.
Power up by connecting AC power with or without battery.
8 (hold-down function).
1. Hold down keypad key
Delay
1 Reset 9 Reset 9 Delete
4.
2. While four LED's are blinking enter programming code (‘1 9 9 4’)
3. If code is valid ‘Installer Progr.’ will be displayed. The two left LED's (Red & Green) blink to
indicate that system is waiting for a new address.
4. Enter the address you want to program (see programming sheet). Current value of address is
displayed, and LEDs will blink.
Note: Blinking of 2 left most LEDs, means system is waiting for new address to be entered;
Enter a 3 or 2-digit address (according to address length.)
Note: 3 blinking LEDs means system is waiting for new value to be entered;
Enter a 2-digit value, or as required.
Program
Siren
EXAMPLE 1:
System in program mode; ‘Installer Progr.’ is displayed and the two left-most LEDs are blinking.
1. Program zones 1 and 4 as ‘Exit/Entry Delayed 1’ zone.
2. Address 104 represents the ‘Exit/Entry Delayed 1’ zones.
Delay
1 Shunt 0 Delete
4 #; current value of this address is ‘1’ (default program.)
3. Press
Three LEDs will blink and a ‘Loc 104 1 - - - - - - -’ will be displayed (default program).
4. To enter new required value press the address number > 104; followed by the new
Delay
1 Delete
4 in uninterrupted sequence; new setting
required value (‘1’ and ‘4’) by pressing
will be displayed to confirm ‘Loc 104 1 - - 4 - - - -’
Siren
Siren
EXAMPLE 2:
1. Program zone 8 as 24H zone (in default, this is an Instant Zone).
2. Address 116 represents the 24H zones.
1
1
6 #; current value of the address is ‘‘Loc 116 - - - - - - - -’’ (‘-’ means
3. Press
blank - no 24H zone is programmed).
1
1
6 #; cursor move to
4. To enter new required value press the address number
8 (zone 8); new setting will be displayed
Upper raw, then enter new value ‘8,’ by pressing
confirms programming updating.
Siren
Siren
Telephone
Siren
Siren
Telephone
Program
Note: At programming enter ‘0’ in order to delete a feature
44
EXAMPLE 3:
1. Program Siren Time for a 2-minute duration (default 4 minutes).
2. Address 063 represents the Siren Time.
6
3 #; current value of the address is 04;
3. Press Shunt 0
Two LEDs blink and ‘04’ will be displayed (default program).
Shunt
4. Enter 063, then a new value of ‘02’ by pressing Shunt 0 Display 2 #. New setting display, confirms
programming updating.
Telephone
Status
EXAMPLE 8: Report to Central Station
Note: To enter data use two digits entry, i.e. in address 201 to change the transmitted code
from the default value ‘3’ to ‘5’, at keypad enter ‘0’ and ‘5’ (not 5).
If ‘5’ entered, an ‘E’ (Error) appears
 Enable communicator to report to central station (in default programming communicator is
disabled, and dialer is activated upon alarm). Telephones 2 and 3 (refer to program sheet) are used
to communicate to central station.
 Contact the central station to get receiver format, event codes, subscriber number,
handshake frequency (1400 or 2300 Hz), and telephone number(s). Two telephone numbers are
available, ‘Tel. 2’ is main central station Tel. Number and ‘Tel. 3’ is backup, in case ‘Tel. 2’ fails.
Do not program different formats for each telephone.
 Refer to part ‘7’ of the programming sheet. Fill in central station’s details. Most important
parameters are the Receiver Format, Handshake frequency and Data Format.
Opening and Closing Reporting to Central Station
By default, (address 072) Closing/Opening reported to central station. The report contains the
subscriber ID; the Closing/Opening events, and the user number (1 to 16).
In order to avoid reporting Closing or Opening for specific user erase the user Closing or Opening
code. The system will check for non-reporting programming and will not initiate dialing if the user
is programmed for non- reporting of Opening or Closing.
If you check the contents of address 242 (00 is programmed), a '-' will be displayed, indicating that
this location is blank (empty).
Communicator’s Subscriber ID Codes - EASY Programming
Refer to part 10 of the programming table; System is in program mode, enter ID address, 4 LEDs
are blinking, enter the subscriber ID code in sequence.
Example: Your subscriber ID number is 2170 for Closing/Opening of telephone 1; refer to address
number 376. Keypad in programming mode, ‘P’ is displayed, press 376, four LEDs are blinking,
enter 2170.
Note: EASY Programming is not included in the EasyLoad screen (programming via
computer).
45
Note: Even if your communicator receiver requires three digits for the subscriber ID, enter
four digits. The system will ignore the fourth digit.
If your central station requires programming of letters as well as numbers, refer to the HEX
programming description. Use the regular programming method of entering each letter or number
in each address, as explained in the programming table (HEX method).
Contact ID Format (known also as Ademco Express): This is the fastest to program and easiest
to use format, with communication speed achieved by the DTMF signaling.
When using this format, program only the CS telephone numbers and subscriber ID; all reports
automatically transmitted, without programming anything else.
To select the Contact ID format: In address 021 enter 07, same for address 022 is you need the
back up reporting, enter the subscriber ID (refer to part 10 of programming table).
The system programmed to report to central station with Contact ID format.
2.8  Reset System to Default Programming
In case you made programming changes and the system operation is wrong it is recommended to
set system to the defaults program. Warning, this function erases all codes and system
programming settings.
1. Enter program mode.
2. Go to address 200 and enter ‘6’ and ‘9’. Display will show Factory Default, and system will
revert to factory default program and codes (Code No. 1 is 1 2 3 4; programming code will be 1 9
9 4)
Note: Erroneous or conflicting programming features are discarded by the system upon quitting
program mode. For example: Programming the same zone as 24H type and Delayed zone will be
recognized only as a 24H zone.
Reset System to Default Codes (In case code is lost)
To enable this feature, verify value 8 in programmed in address 072.
Power down, than power up by applying the AC power. After power up wait until the keypad
display the panel version, and status LED light on.
Press both
# during 5 seconds (after applying AC); sounder beeps during
* together
Hold-down keys
the hold-down, release keys; **** OK **** displayed in confirmation.
User code No. 1 (1234) and programming code (1994) will reset to default.
2.9  Dialer- Communicator; explanation and Programming
Series 2000 Defining the Communicator and Dialer feature
46
Communicator
The Communicator is in essence, a dialer that enables communications with a central station
digital receiver. The Communicator reports (upon programming) panel events such as Opening,
Closing, Alarm, and Low Battery.
The Communicator's programmable features enable compatibility with different central station
receivers. The receiver’s most important features are the Format (Radionics, Contact ID, etc.) and
Data Transfer Mode (1 x 3, 2 x 4). The Dublo series supports only Contact ID format.
The four programmable telephones (telephones 1 to 4) act as dialers, while Tel. 2 and 3 (Tel. 3 is
backup for Tel. 2) are optional as communicator or dialer.
Program the communicator and dialer options at addresses 201 and 202. Do not program only
Telephone 3 as communicator. At alarm, Tel. 2 and 3 are in priority, if programmed as
communicator. The communicator phones are first to communicate (before dialer phones).
In the ‘Communicator’ mode, the panel will dial several times until the central station sends a
confirmation signal (Kiss-Off) that all events received. The Kiss-Off signal turns the
communicator off until the next event occurs. If the CS telephone number is busy, panel will redial automatically. The number of dialing attempts (cycles) is programmable at address 087.
In case first central station telephone number (Tel. 2) does not get Kiss-Off after several attempts,
the system will dial the back-up number - Tel. 3. Program both Tel. 2 and Tel. 3 as communicator.
Program the same reporting format for Tel. 2 and Tel. 3. When the system is disarmed, AC Fail is
reported 30 minuets after power fail to prevent false alarms.
To cancel the communicator dialing: Enter to Program Mode and Exit program.
Dialer
The Dialer acts similarly to the communicator, except that the panel sends a recorded alarm tone
or vocal message with SVM-40/60, (not a digital signal) to a regular or mobile telephone. Unlike
the communicator, the dialer does NOT identify busy signals; program the dialer to re-dial several
times (default is 3 cycles). This feature is programmable at address 087. A ‘Follow-Me’ feature
(see explanation in Glossary section) is applicable only with the dialer, in alarm the Follow-Me
number dialed first if communicator not selected.
To cancel the dialer dialing: Arm and then Disarm the system.
Note: Upon alarm, the communicator has dialing priority over the dialer.
Programming Telephone Numbers
1. Enter Program mode as described in programming description.
2. Select Dialer or Communicator mode (addresses 201, 202). For dialer selection, enter 00 in
address 201 for Tel. 2, and in address 202 for Tel. 3. (Tel. 1 to 4 is in Dialer mode by default).
If communicator is selected, use both Tel. 2 & 3 (not Tel. 03 only). Tel. 3 is backup for Tel. 2.
3. Enter the required telephone numbers (maximum 16 digits) at address 010 to 013. For
example program Tel. 1 to be 00972-36816767; Press 010, the two left LED's blink, enter the
number 00972 in sequence, hold-down ‘0’ (pause), enter 36816767; wait for ‘u’ confirmation.
To insert * in the telephone number; Hold-down keys # and * (panic); * will be displayed as
‘A.’ (* is valid during dialing in DTMF mode).
47
For Dialing Pause hold-down key ‘0.’ Note: Two pauses (one following the other, or a pause
at the end of the telephone number) are not valid. Maximum 4 pauses per Tel. number.
4. To quit the programming mode Hold-Down key ‘9’.
2.9.1  Deleting Telephone Numbers
1. Enter program mode
2. Press 010 plus # (address 010) for telephone No. 1, current telephone number displayed
3. Press 010, cursor move to upper raw, hold down * and # for two seconds, E displayed to
confirm the number Erased. To exit 999 #
2.9.2  User Programming of ‘Follow-Me’ Telephone Number
To program the Follow-Me number, disarm the system (‘USE’ mode).
1. Hold down key [6] twice, ‘Follow Me Phone’ displayed
2.Enter Telephone Number (maximum 16 digits and 4 pauses) plus #, ‘Follow-Me’ number
programmed.
3.010 – Phone # 1 displayed in confirmation
2.10  Quitting Programming Mode
Upon completion of programming, press 99 # to quit User Programming and 999 # to Quit
Installer programming mode
2.11  Verification of Current Programming
(Programmed Values)
8 and enter programming code (1994) plus #.
Enter to Program Mode by holding down key
Enter address to be verified. The value of that address will be displayed, press # (enter) move to
go to next address, press * to move to previous one.
Program
2.12  Downloading from a computer
Up and downloading via Modem and Computer (EasyLoad DOS version 3.00 and higher)
EasyLoad Introduction
The remote up and download feature enables fast and simple programming of EasyLoader panels.
Programming tables, codes and other features may be up & downloaded from an onsite PC (DOS
Mode, 386 or higher) by using an AV-232 adapter cable, or via telephone using a modem and
‘EasyLoad’ software. ‘EasyLoad’ is compatible with DOS Windows XP and Windows 95/98.
To program EasyLoader control panel by remote PC, a compatible modem required. The modem
specifications is critical, before attempting to operate the EasyLoader make sure your modem meet
the following: Supports the Hayes AT command, Bell 103 compatible, DOS mode is selectable.
48
EasyLoad software supports most modems manufactured after 1994, including: US Robotics,
Hayes, Viva, Boca, Microcom, Netcom Roadster 288, Acer 336, PCMIA 3 com 3CCM156B,
Motorola Lifestyle 28.8, Dataplex Multispeed V.32bis, Netcom Smart modem 56, Acer AMEMU00, ABC 56K V.90, and other Hayes and Bell 103 compatible modems.
Installing EasyLoad on your Computer
Insert the EasyLoad diskette in the floppy drive A (or B) and type ‘A:’ (or ‘B:’). At prompter
‘A:>‘ type ‘AVGAD3’ (AVGAD3 is the file name). The installation program will guide you, and
will install EasyLoad automatically by creating a new directory on your hard drive, called
AVGAD, or a name of your choice.
To start your EasyLoad: at the prompt ‘C:\AVGAD>‘ type ‘ESAV’.
IMPORTANT! The most current updates and EasyLoad features are in the READ ME file.
Read it carefully before using the EasyLoad.
Factory default access code is AVGAD123. Change it when installed. Update it periodically.
The first time you run the program, missing “Files Message” displayed (the database), answer
‘Yes’ to create them.
The main EasyLoad menu contains seven selectable fields. Enter those fields by using the
navigation arrows on your keyboard, or by typing the field number.
Using a mouse is highly recommended. The keyboard can also be used to navigate through the
fields, e.g. Move from field to field using arrows (when possible), the TAB key (forward), SHIFT
+ TAB (backward), ALT key + Highlighted letter. Confirm input in text fields by hitting the
ENTER (return) key. In the main menus, you may type the highlighted digits for fast access.
Step 1: Configuring your Modem
Configure your communication port using the SET-UP entry from the main menu (entry 7).
For DOS modems the required COM/IRQ combinations are:
COM1, COM3 - IRQ 4
COM2, COM4 - IRQ 3
To initialize the modem properly, use the Auto Detect option before trying to CONNECT, ignore
errors that are reported during initialization.
The integrated modem in EasyLoader control panels operates in ANSWER mode.
The dial suffix from the Set-Up screen is no longer relevant! The modem will be silent until the
control panel answers the call, then the Modem noise is on (the carrier detection procedure).
After connection made, the modem's speaker will turn OFF. In this operation mode, you will be
able to hear the call progress tones (dialing, ringing or busy). If the phone line is busy, the program
will notify you and will disconnect the telephone line.
To get an outgoing telephone line from an extension, fill in the PABX entry on the set-up screen.
Type the digit needed for the outgoing line (usually 0 or 9) followed by a W. The ‘W’ will pause
the modem until it gets the second dial tone (from the outgoing line) thus avoiding blind dialing.
Troubleshooting: Where a PABX installed, local PABX stations (telephone system) are fitted
with internal modems for remote set-up. These stations, much like the control panels, activate
their modems in ORIGINATE mode.
49
When connecting through PABX to a telephone number without getting an answer, the station will
eventually activate its modem in response to the computer's modem. The communication program
then informs you that connection to the panel established! A few moments later, it will disconnect,
because there is ‘no response from panel!’ If you usually dial to control panels that will answer
after a long while and the phone station interferes each time, try to use a direct line.
Step 2: Opening a Client Account
When opening a client account (selection 1 in the main menu), make sure to enter the ‘Panel
Phone Number.’ This is the telephone number to which the EasyLoad program will dial for the up
and download operation. Fill in all client details.
The first time you open (create) a client account, you must choose the control panel model. You
cannot modify it later!
To open another client account, select New and enter the account number.
To display the list of all the client accounts, press on the ‘List’ button. You will get a sorted list of
the clients. Press the SPACE bar to have the list sorted by NAME or Account Number.
To search for a name or any string, press the ‘Search’ button.
Pay attention to the panel models! There are few models.
AV-2008, AV-2016 Dublo internal modem operate in Answer mode.
This code is initially empty (a string of spaces). When leaving the factory, the control panel is
initialized to an empty code too.
The first time the PC contacts a ‘virgin’ control panel it transfers the dealer code (from the client
record) to the panel's memory.
From this moment, any further dialog with that panel will require the dealer code. Note that the
dealer code in the client record is empty, it ‘matches’ the panel empty code and communication is
possible.
This means you can choose not to use dealer codes. On the other hand, once a dealer code
transferred to the panel, to erase or modify the code is impossible. Access to the panel is
granted only with this code.
To open another client account, select New and enter the account number.
Step 3: Modifying the Programming Table
Select field 2 from the main menu. This will take you to the Programming menu. All settings are
the factory defaults.
Select the programming table section you would like to modify. Save and exit.
Feature and code modifications are updated on the control panel at upload.
You can modify or inspect the programming table while connected to the control panel (‘on-line’).
Warning: The control panel will answer an incoming call upon the number of rings set in the
Dialing Parameters, in address 091. The control panel will not answer the telephone when this
number is set above 20 rings. The factory default is 10.
Step 4: Connecting
Check your PC time and date before connecting to a control panel!
50
Upon selecting ‘Connect,’ the modem will dial to the currently selected client (see Step 2, for
programming client telephone number).
While the connection established, a high-pitched tone is heard through the modem's speaker (this
is the carrier sound). Learn to recognize the tones, and pay attention to the sound, because in its
special operating mode, the modem cannot detect BUSY and other call progress signals.
The PC modem will hang up automatically if it does not get an answer from the remote panel in
60 seconds.
When the remote Control Panel answers a call and detects the carrier from the PC modem, the
panel enters the programming mode and will remain in this mode until it gets a disconnect
command from the PC, or connection is lost due to bad phone line (loss of carrier). After
disconnecting, the Control Panel remains in its previous operating mode unless its status was
modified in the ‘Commands to Panel’ section.
If a user attends the remote panel, cancel connection by holding down the ‘9’ key on the keypad.
While connected, the programming table can be downloaded, modified and uploaded to the
control panel.
If the history log is downloaded, it can be viewed also after disconnecting. At present to print
history is not available.
Important: The Control Panel status (Armed/Disarmed), as set by the communication
program, is changed AFTER disconnecting from the remote PC.
Upon reception of the ‘change mode’ command, the control panel replies with the ‘new’ mode. It
might be different from the one displayed on the computer monitor.
For example: Group Bypass will not be acknowledged if no such zones were programmed. The
same applies to manual bypassed zones. If one accidentally tries to bypass all the zones, the
control panel will discard all bypassing.
Address 092 enables ‘Answer Now’ (answers remote computer after 1 ring). The user attending
the control panel can reduce the number of rings before answer to one ring.
Answering machine bypass
In case the alarm panel connected with fax or answering machine on the same telephone line (not
recommended) enable the Answering Machine Bypass or Answer Now features (otherwise
connection is impossible).
To enable the feature:
1. Program 7 at address 076
2. Program at least 20 seconds at address 097 (Ring Time Out)
Now dial to the control panel, count at least three rings and disconnect, dial again immediately –
the panel will answer at first ring.
51
When Answering Machine Bypass enabled, the control panel will answer at first ring if:
- There was a pause of at least 10 seconds from last ring
- The panel already counted at least three rings before the pause
- Number of rings to answer (at address 091) is less than 20
Notice:
The panel will answer (in a normal mode) if there is no pause and the rings counted exceed (or
equal) the number programmed at 091.
Step 5: Disconnecting
When download completed, disconnect the PC from the remote Control Panel by selecting
‘Disconnect’ from the main menu.
Control panel status after disconnection:
A remote PC might connect the control panel while unattended by the owner, the following must
be taken in account:
 The panel will always ARM (if told so by the remote) regardless of the status of zones. That
means that currently open zones will not prevent the panel from Arming (not possible with the
keypad).
 After a remote connection the history log is not cleared.
 For Belgian standard user: If the alarm was caused by ‘Tampering’ the zones, and the ‘Lock
System After Tampers Alarm’ feature was programmed, the system will remain locked while it is
Armed.
 If the control panel was contacted after an alarm, and then Armed or Disarmed, the last events
are not cleared. Thus, even after being disarmed by the remote PC, the keypad still displays the
zones that caused previous alarms and the status LED blinks (although there are currently no open
zones). Pressing the Reset (hold down '9') key will clear these alarms.
 Instruct the owner to clear the history log from time to time. This will keep the history log
reasonably short (the maximum event number is 250) and will cut down the download time.
Zone Description Transfer
Zones and Logo texts are possible to Upload/Download via PC. Texts uploaded automatically to
the keypads after communication is closed.
Events logging
‘History’ events are ‘date’ stamped. The control panel time and date are synchronized to the
remote computer when connection is made (as well as when the control panel status is changed by
remote PC command).
The control panel date can also be locally set, using the keypad by the hold-down
‘0’+’2’+ddmmyy (‘0’ and ‘2’ mean ‘hold down’ keys 0 and 2).
Instruct the control panel user to update the system time and date after a total power loss (‘h’ is
repeatedly displayed at the keypad).
The EasyLoad software designed to support international users, to modify and translate the
LANGUAGE.TXT, LANGPROG.TXT, LNGPRG16.TXT, and HELPPROG.TXT files use an
ASCII editor. You can translate captions in these files to other languages.
52
In the DEFXXXX.TPL, DEFXXXX.TPL and DEFXXXX.TPL files (XXXX represent the panel
type), some captions can be translated (be careful with these files!). Caution! Make sure to
backup the files before altering them. See details in the files themselves.
Local Up and Download via PC
When using the AV-232 interface (special RS-232 cable and interface connecting the PC to the
Av-Gad control panels) you must set panel to programming mode. In programming mode
(Installer Prog. is displayed), type 77 at address 200 (i.e. type 20077) before attempting to
establish connection timeout is 4 minutes). When using the AV-232 interface, the transfer rate is
eight times faster than through the modem. With local PC, use the same procedures as describe
below.
Copying the Programming Table
To cut down the time spent on programming several accounts with practically the same data
(communicator parameters, communicator codes, central station telephone numbers, etc.) you may
create a few ‘master’ accounts. For each control panel model you intend to use, create a ‘master’
account containing the relevant programmable data. This ‘master’ account is in no way different
from a regular account. Choose an account number that is easy to remember and enter a short
description instead of the ‘client name.’
After creating a new client account, exit to the main menu and choose ‘Copy Programming Table’
(entry 6) option. In this screen, type the number of the ‘master’ account you want to copy.
Confirmation of the copy operation will transfer the whole programming table of the master
account to the currently open client file. You can now make other adjustments by choosing the
‘Modify Programming Table’ (entry 2).
Full instructions and latest features enclosed in the EasyLoad software diskette.
Manual Answer Now Modem Setting
See address 092, set to ‘0’ to disable or ‘1’ to enable (1 by default).
Procedure
1. Address 092 set to 1
2. Enter User 01 code (1234 by default), hold-down key 8.
3. ‘u’ is displayed.
4. Enter 66, ‘A’ displayed and few beeps in confirmation, no other indication. For next 5 minutes,
after the first ring, the modem is connected.
53
4. TROUBLESHOOTING
Symptom
Possible Cause
Remedy
Keypad failure
 Incorrect
 Check
Keypad displays ‘8,’ but does
not react to pressing of keys
wiring
 Blown fuse
Incorrect connection of
data wires
 Hardware fail
color wire connection
 Check power at panel
Check Orange and Yellow wire
(or terminal block) connections
at keypad and system
Close or bypass zone 8
(zone 8 is 24H-type by default)
 Connect AC power, verify
that main socket is alive
 Check transformer
Arm and disarm
Panic alarm address should
have a value greater than ‘0’
(zero). See address 050.
 Siren time-out addresses
should have a value greater
than ‘0’ (zero)
 Check fuses and
 Check that sirens operates
 Check address 201 and 202
 Test telephone line
 ‘EOL Zone’
 If
Keypad displays ‘Zone 8,’ and
keypad buzzer is sounding
3 LEDs flashing, AC fail is
displayed
Zone 8 is troubled
‘H’ is displayed
No siren upon keypad panic, but
siren test is OK
Panic keys were pressed
Faulty programming
No siren upon alarm at troubled
zone
 Programming
Dialer dials, but no alarm
message is transmitted on
telephone
Zone is troubled even though
EOL resistor is connected or
zone is wire bypassed
 Faulty programming
System self-arming
 Remote
Display of ‘Open Zone’ and
Arming is denied
Power failure
 Siren
fuse
 Alarm device blown
feature
incorrectly programmed
 Incorrect resistor value
key wires are
too long
 Key ‘5’ was
programmed for ‘Instant
Arming’
Instant zone is troubled
54
EOL mode is programmed,
connect resistor across zone
terminal for testing
 Use 2.2K resistor
 Run shorter wires from panel
to remote key
 Disable key ‘5’ (instant
arming) by reprogramming
address 071
Bypass or clear the troubled
zone
Symptom
Possible Cause
Remedy
Cannot disarm system
 Code
 Keypad
Power to keypad is OK,
communication wires are
incorrectly connected, or
are disconnected
Battery fuse failure
 Test
‘P’ displayed after attempt to
change end-user code
‘8’ displayed keypad keys do
not response
‘Low Battery’ displayed upon
arming, but battery is OK
was changed
before instant arming
 ‘Lock in tamper mode’
Verify the last User-Code
In alarm mode, Aux. power
drops below 10V
Aux. power overloaded
No Entry delay
Key ‘4’ (delete delays)
was held down
Faulty programming
Programming fails to update
features
Upon Arming, Bypass (shunt)
Orange and Red LEDs light up
Dialer does not dial on alarm,
even though line and connection
are OK
Remote signaling outputs do not
drive (-)
wires are too long
 Disable instant arming
 Verify address 071 value ‘6’
You may proceed with ‘Default
Programming’ to revert system
to default codes
 Make sure wiring is correct
 Check wires at panel
 Replace keypad
system without AC
power; if inoperative, battery
fuse not rested
 Disconnect battery wires and
wait 5 minutes
If current consumption of Aux.
power exceeds max. rate, add
external power supply (AV-21)
Arm and then disarm to cancel
this function
Verify programming features
Auto bypass of instant
zone was programmed
Programming error
Verify programming address
034 - Zone Auto Bypass
 Dialer or communicator timeout addresses should have a
value greater than ‘0’ (zero)
 Overload
 Current
 Incorrect
testing
55
consumption from
output to load should be not
higher than 50 mA (test outputs
by connecting voltmeter from
output to (+) Aux. power; upon
signaling, meter should read
12.5 to 13.6 Volts)
Symptom
Possible Cause
Remedy
Buzzer sounds in disarm mode
Hold-down function was
entered or Day zone
triggered
User code is unknown
User forgot the Arming
code
 AC power is too high
 Power supply
overloaded or faulty
battery (shorten)
Arm and then disarm to cancel
chime and fault find features, or
hold-down key ‘9’ to reset day
zone alarm
Refer to ‘Resetting Codes to
Default’ feature
 Measure the low AC power;
should not exceed 17V
 Try to disconnect sensors,
keypads or other loads that
consume high current
Panel’s PCB is getting hot,
system doesn’t function
normally
For additional assistance, please contact first your local distributor, in case problem
not solved contact Av-Gad Systems Ltd, mention your vendor.
Our telephone: +972-3-681 67 67, Fax: +972-3-683 5505, E-mail: avgad@inter.net.il
Mail: POB 49 080, Tel-Aviv 61 490, Israel. Web site: www.av-gad.com
56
SECTION V: WIRING DIAGRAM
Figure 9: AV-2008 Dublo Wiring Diagram
WARNING:
To prevent
electrical shock,
disengage the
System and
disconnect the
telephone line
before servicing
this unit.
-
BATTERY
+
Q11
D12
C38
C37
Q12
R71
R83
-V
C20
E
B
E
B
30
R80
R79
Q10
D13
Fuse
-SIR
AC 16V
JP1
6
1
U5
R51
R50
R53
R1
D1
R31
JP4
R32
CBE
R58
AC
AC
Q2
D8
C14
+
R60
R97
R20
VA10
C3
R114
U2 Q17
AV-GAD
Fuse
R7
R5
R10
R6
R4
Expander
Connector
D7
E
R116
U1
R98
R59
E BC
B
1
C42
C13
R54
1
J1
R92
Q4
Q3
RF2
R9
R2
R93
13
+
Y1
R3
CBE
C47
1
C9
R25
AC 16V
Indoor
Siren
21
38
U8
SIR2
SVM IN
U9
T1
38
C26
C6
SERIAL
(AV-232)
JP2
R100
D17
VA13
R78
C5
C1
+V
TX
C36
13
88
C48
C23
R109
KEY
SIR1
U6
63
C27
R73
C15
C31
-V
R102
+ VA12
C39
C29
R76C28
R74
C43
R106
1
R85
+Q9
D9
5
R103
R101
+
C41
U7
I
D10
+BATT
Outdoor
Siren
C44
C40
Fuse
RX
++
+
R94
R61
D11
-BATT
D16
JP3
R95
C45
R90
C25
Fuse
KEY
R87
R96
R91
Q15
R86
R104
B
R111
R88
D15
R12
R14
R11
R13
R16
R19 R23
R17 R18
C E
B B
E C
U4
DIAL
Q18
VA14
R22 D3
D2
TEL. LINE
R15
PHONES
AUSTEL
MAX 1A
+12V -V
1
2
3
4
5
6
7
8
-V +12V OR YE A1 ON SLO SLO 1
2000 SERIES V3
Fuse 0.5A
220V
To 220V AC
Cold Water
Grounding
Use
3m"m
Wire, run five
meters Max.
A1 ON SLO SLO1
AV-GAD EASYLOADER AV-701
ZONE
DISPLAY
A1 Remote Indication
Siren
1
Shunt
Display
2
Status
3
Delay
Delete
4
Chime
5
Telephone
6
Test
7
Program
8
Reset
9
*
EOL Resistors are 2,220K Ohms
Shunt
0
#
ON Indicates Arming
SLO (Selective Output)
SLO 1 (Selective Output)
1 Transformer: Connect fused (0.5A) transformer to a non-switched main outlet.
5 EOL Resistors: Use 2200 ohms (2K2) resistor.
Make sure to use fused main not connected to an automatic switch.
6 Keypad: Connect maximum of three AV-706, 707 keypads.
2 Grounding: Connect Ground from the board to Cold Water pipe (ground),
7 Remote Arming: Use spring-return lock type; run wires of 20 meters
using 2-2.5 m2 wire, as short a length as possible, and no more than 4 meters.
maximum, or use wireless remote device to Arm/Disarm System.
3 Fuses: All fuses are Electronic type. If fuse hot, power down and wait
4 Battery: Non-replaceable type Fuse. Recommended Battery: Sealed Lead
8 Sirens: Connect horn-type siren (speaker) or 12V DC type (Bell). If using Bell
Acid type 12V - 7.2 AH.
9 Tel Line: Dialing is applicable for DTMF and PULSE telephone systems.
adhere to maximum ratings (see Siren paragraph).
SECTION VI: INDEX
A
Double-Pole Zone, 9
Downloading, 49
DTMF remote control, 18
Abort Report, 39
AC Power, 7
Address, 36
Answer Now, 23
Answering machine bypass, 39, 52
Arm and Disarm, 28
Arming - Upon all Delayed Clear,
40
Arming & Disarming Key and
Wireless, 18
Arming Code, 30
Audible Test on Arming, 39
Auto Arming, 29
AV-232, 53
AV-816 Connection, 11
E
End-User Code, 30
Entry Delays 1 and 2, 40
Events History, 25
Exit Delay, 40
Expander, 11
F
Factory Default, 37
Fast Response, 40
Fault Find, 24
Fire Zone, 40
Follow Me Programming By User,
48
Follower Zone, 40
Follow-Me Erased Automatically,
40
Force Opening Code, 34
Fuses, 8
B
Back-Up Battery, 15
Battery Charging, 7
Battery Test, 7
Bell Mode, 7
Bell Mode, Connection, 14
Buzzer, See Sounder, 26
Bypass Group, 41
Bypass Manual, 41
G
Green LED, 28
Grounding, 15
Group Bypass, 22
Group Bypass (Home Mode), 41
C
Chime, 23
Code 8, Visitor Code, 30
Code No. 7 for Access Control, 30
Communicator
Report-Central
Station, 45
Contact ID, 46
H
History Events-Detailed, 24
Hold-Down Function-Cancel, 26
Hold-Down Functions, 22
Housing, 7
Humidity, 7
D
Day Zone, 39
Default Programming Setting, 46
Default Programming Table, 36
Delay Delete, 23
Delayed Zone, 39
Dial Parameters, 39
Dialer, 7
Dialer Test, 23
Dialing, Default, 7
Display Last 2 Users, 26
Door Chime, 23
I
Instant Arming, 41
Instant Zone, 39
K
Keypad Functions, 21
Keypad Keys Self Locking, 29
Keypad Mounting, 9
Keypad Wiring, 12
58
Off Siren Time, 42
On Siren Time, 42
Opening/Closing Reporting, 45
Shunt Display, 22
Siren Test, 22
Siren Test, upon Arming, 39
Smoke Detector Reset, 40
Sounder, 26
Sounder Response, 26
Specifications, 7
Status Display, 22
SVM Module, 43
SVM-40 Voice Module, 17
Swinger Shut-Down Zone, 43
P
T
Panic Button, 26
Power Failure, LEDs Indication, 28
Powering Up, 16
Program, Verify, 48
Programming Auto Dialer, 47
Programming Code, 30
Programming Code (Code 17), 42
Programming Examples, 44
Programming Quitting, 48
Programming Sheet, 32
Tamper Alarm-Lock in Arm, 41
Tampered Zones History, 26
Telephone Numbers, Delete, 48
Telephone System Dialing, 17
Temperature, 7
Test Signal to Central Station, 43
Testing Detection Devices, 24
Time Setting, 25
Troubleshooting List, 54
Twenty Four (24H) Hours Zone, 39
R
U
Red Fire Led, 28
Red LED, 28
Re-Dial Cycles, 42
Relay Module, 15
Remote Momentary Key, 18
Report Bypassed Zones, 43
Reset Events Memory, 26
Reset for Smoke Detectors, 40
Reset Functions, 24
Resistor (EOL), 7
Up and Download, 49
L
LEDs Flashing, 28
N
No EOL Resistor, 42
No Reset Zone, 41
O
V
Value, 36
Y
Yellow LED, 28
Z
Zone In Use, 44
Zone Wiring Mode, 9, 12
Zones Reset, 41
S
Shunt, 21
59
AV-GAD LIMITED WARRANTY
Av-Gad Systems Ltd. (Av-Gad) warrants it’s products to be free from production defects in components;
materials used and labor for twelve months following the date of production. Av-Gad will within the
mentioned period, as its option, repair or replace any product failing to proper operation without
charging the purchaser.
This warranty shall not apply to any equipment, or any part thereof, which has been
repaired by others, installed not properly, used improperly, abused, altered damaged or
subjected to forces of nature or on which the serial and data code is altered or removed.
Av-Gad will not be responsible for any dismantling or reinstallation expenses. In order to
exercise the warranty, the purchaser must return the product; delivery and transportation
costs will be prepaid and insured to Av-Gad.
After repair or replacement, Av-Gad assumes the cost of returning products under
warranty.
There are no warranties, expressed or implied, which extend beyond the description of the
face hereof.
There is no express or implied warranty of merchantability or a warranty of fitness for
particular purpose. Additionally, this warranty is in lieu of all other obligations or
liabilities on the part of Av-Gad.
Any action for breach of warranty, including but not limited to any implied warranty of
merchantability, must be brought within three months following the end of the warranty
period. In no case shall Av-Gad be liable to anyone for any consequential or incidental
damages for breach of this or any other warranty, expressed or implied, even if the loss or
damage is caused by the seller’s own negligence or fault.
Av-Gad is not an insurer of either the property or safety of the user’s employees, family,
or 3rd part and limits its liability for any loss or damage including incidental or
consequential damages to Av-Gad original selling price of the product regardless of the
cause of such a loss or damage.
Av-Gad hereby declares that service, technical support and spare parts will be supplied for 60 months
following the date of production. Price list for such services to be updated from time to time.
Item 4712_DBL
60
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising