Dynasty Spas SSPA-1 is a single-pump spa system that offers a range of features for a relaxing and enjoyable spa experience. With its simple keypad interface, you can easily control the pump, light, and water temperature. The built-in timer ensures that the pump and light automatically turn off after a set period, saving energy. The SSPA-1 also includes a water heater that maintains the desired temperature, with an indicator light to signal when it's on. Enjoy customized filtration cycles and automatic freeze protection with Smart Winter Mode.
advertisement
SSPA-1 SPA PACK
•
Single-Pump System
•
This Quick Reference Card is a summary of your spa's main functions and provides a quick overview of operations accessible from your spa side keypad.
To start the pump:
Press the Pump key to turn the pump on at low speed.
A second press will turn the pump to high speed. A third press will turn the pump off. A built-in timer will shut the pump off after 20 minutes unless it has been manually deactivated.
The "Pump" indicator light will be on when the
Pump is running.
"Pump" indicator light
To turn the light on:
Press the Light key to turn the light on. A second press will turn the light off. A built-in timer will shut the light off after 2 hours unless it has been manually deactivated.
The "Light" indicator will be on when the light is on.
"Light" indicator
To change the water temperature:
Press the Up or Down arrow key to increase or decrease the desired water temperature. The selected temperature setting will be displayed for 5 seconds as a confirmation.
The "Set Point" indicator light indicates that the temperature shown is the desired, and not the current, temperature of the water!
The temperature can be adjusted in 1-degree increments from 59 to 104˚F (15 to 40˚C).
Water heater automatic start:
When the water temperature is 1˚F (0.5˚C) lower than the set point, the heater will be turned on automatically until the water temperature reaches the set point plus 1˚F (0.5˚C).
The "Heater" indicator light will be on when the heater is on.
Note: If your system is configured in Low Current Mode, the heater will not start if the pump is running at high speed.
"Heater" & "Set Point" indicator lights
Quick Reference Card
HOW TO PROGRAM THE FILTER CYCLE DURATION
The system will automatically perform two filtration cycles per day, 12 hours apart. During a filter cycle, the pump runs at low speed for a predetermined number of hours. The ozonator is also activated. The "Filter" indicator light will be on when a filter cycle is in progress.
To set the filter cycle duration:
Press and hold the Light key for
5 seconds. The display will show the currently set filter cycle duration in hours.
Use the Up or Down arrow key to change the setting.
0 = no filtration
12 = continuous filtration
An irregularly flashing "Filter" indicator light indicates that the system has stopped filtering after 3 hours because the water temperature exceeds the set point by more than
2˚F (1˚C). If the temperature cools down to 1˚F (0.5˚C) above set point before the scheduled end of the cycle, filtering will resume for the remaining of the programmed duration.
When the desired setting is displayed, press the Light key to confirm. A filter cycle will start immediately.
Note: After a power failure, the filter cycle duration will return to its default value (6 hours). In this case, the first filter cycle will start 12 hours after power has been restored.
TROUBLESHOOTING
Pumps have started up for one minute on several occasions and
"Filter Cycle" indicator is flashing.
Not a bug but a feature!
Our Smart Winter Mode protects your spa from the cold by automatically turning pumps on for one minute several times a day to prevent water from freezing in pipes.
3 flashing dots are displayed.
A problem has been detected.
Do not enter the water! Check and open water valves.
Clean filter if necessary. Check water level. Add water if necessary.
Shut power off and power your spa up again to reset the system.
Call your dealer or service supplier if problem persists.
Water temperature is flashing.
The display is flashing.
Water temperature in the spa has reached 112˚F (44˚C).
Do not enter the water! Allow water to cool down. The system will reset automatically when water temperature reaches 109˚F (43˚C).
Call your dealer or service supplier if problem persists.
A power failure has occurred. Press any key to reset the system, then reprogram all desired parameters.
• E
Q U
I P P
E D W
I T H G E C K O ' S E X C L
U S I V
E •
Smart
Winter
Mode
TM
1.800.78.GECKO
9919-100099-B
GECKO
advertisement
Key Features
- Single-Pump System
- User-Friendly Keypad
- Automatic Filtration Cycles
- Adjustable Filtration Cycle Duration
- Smart Winter Mode
Related manuals
Frequently Answers and Questions
How do I set the filter cycle duration?
What is the purpose of the Smart Winter Mode?
What does it mean when the "Filter" indicator light flashes irregularly?
advertisement