Dynex | 57" Combination Monopod-Tripod - Black | Quick Setup Guide | Dynex 57" Combination Monopod-Tripod - Black Quick Setup Guide

Dynex 57" Combination Monopod-Tripod - Black Quick Setup Guide
Converting to a monopod
Storing your tripod
1 Holding the tripod firmly, unscrew the monopod leg from the
main tripod assembly.
1 Remove your camera.
2 Loosen the center column locks. Raise the column as far as it
will go, then tighten the bottom lock. Lower the top section as
far as it will go.
3 Twist each leg lock counterclockwise and collapse the legs.
4 Wrap your hand around all four leg locks, then twist clockwise
to tighten them all at once.
5 Pull out the leg release tabs and flip the legs up.
Note: You may need to rotate the head slightly so the legs fit between
the knobs.
6 Store the tripod into the carrying case.
Monopod leg
2 Unscrew the center column locking screws, unscrew the bottom
hanging hook, then remove the center column from the tripod
base.
Center column
Hanging hook
3 Screw the center column (with ball head) into the monopod leg.
DX-TRPMN57
57" Compact
Tripod-Monopod Combo
Important safety instructions
• Make sure that all leg locks are correctly tightened and that the
legs are fully opened before use.
• Do not carry or transport your tripod with camera equipment
attached (for example, over your shoulder or cradled in your
arms).
• Do not expose your tripod to excessive heat or cold, or use near
any flame or fire.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod. Use
only a mild detergent and wipe dry with a soft, lint-free cloth.
• Do not exceed the load limit of this tripod.
Specifications
•
•
•
•
•
•
•
•
•
Maximum operating height: 57.1 in. (145 cm)
Minimum operating height: 6.7 in. (17 cm)
Folded height (reversed legs): 13.4 in. (34 cm)
Net weight: 2.7 lbs (1.24 kg)
Max operating load: 8.8 lb (4 kg)
Number of leg sections: 5
Quick release thread: 1/4 in. (0.6 cm)
Panoramic angle: horizontal: 360° and vertical: 90°
Material: aluminum alloy
One-year limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex:
For customer service, call 800-305-2204 (U.S. and Canada) or
01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a registered trademark of BBY Solutions, Inc.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 BBY Solutions, Inc. All Rights Reserved.
4 To adjust the height, unscrew the leg twist locks, extend the leg
to the height you want, then tighten the leg locks.
Before using your new product, please read
these instructions to prevent any damage.
V1 ENGLISH 14-0371
QUICK SETUP GUIDE
Package contents
Setting up your tripod
• Tripod
• Carrying case
• Quick Setup Guide
1
2
3
4
Swing each leg down.
With one hand, grab all the leg locks on one leg and twist them
counterclockwise to loosen them.
Extend the leg sections to the height you want.
Twist each leg lock clockwise to tighten it. Repeat for each leg.
Caution: Incorrectly securing a leg lock can cause the tripod leg to
retract unexpectedly and could result in damage to the tripod or to the
attached camera or camcorder.
Features
• Compact portable size, with built in bubble level, can support a
camera up to 8.8 Ibs (4 kg)
• One leg conversion to use as a monopod
• Super-low 6.7 in. (17 cm) shooting angle
• Reversed folding reduces storage space requirement to 13.4 in.
(34 cm)
5
6
7
8
9
To set the angle position, pull out the angle adjusting tab and
lift the tripod leg, then press the angle adjusting tab in place.
Adjust the center column by unscrewing the center column
locks and raising the center column to the height you want,
then tighten the center column locks.
To remove the quick-release mounting plate, unscrew the
quick-release mounting plate locking knob, then lift the plate
away from the head.
Align the bottom of your camera or camcorder with the 1/4"
mounting screw, then secure your camera or camcorder to the
plate with the screw. The screw should be tight.
Slide the plate onto the tripod head. Turn the quick-release
mounting plate locking knob until it stops to secure the plate.
Using your tripod
Reversed
folding
One leg monopod
conversion
#
Item
Description
1
Quick-release
mounting plate
Mount your device to this removable plate.
2
Mounting base
plate
Holds the quick-release mounting plate.
3
Variable angle
ball head
Allows the camera to be adjusted to any angle.
4
Pan locking knob Locks the horizontal movement of the ball head.
5
Quick-release
mounting plate
locking knob
Locks the quick-release mounting base plate to
the tripod.
6
Ball head locking
knob
Lets you adjust the angle of the ball head.
7
Center column
locks
Lock the first and second sections of the column.
8
Angle adjusting
tab
Lets you adjust the leg angle position.
9
Center column
Adjustable column provides a quick height
adjustment.
10 Grip sponge
Grip the tripod comfortably.
11 Hanging hook
Hang a heavy item on this hook to add stability to
the tripod.
12 Twist screw leg
lock
Locks the legs in place.
13 Rubber feet
Provide a secure, non-slip footing for your tripod.
1 To adjust the horizontal movement of the ball head, turn the
pan locking knob counter-clockwise, move the ball head into the
position you want, then lock the ball head in place by turning the
knob clockwise until tight.
2 To adjust the head ball, turn the ball head locking knob counterclockwise, adjust the ball head, then lock the ball head in place
by turning the knob clockwise until tight.
3 For low angle shooting, unscrew the hanging hook, then remove
the center column. Reverse the direction of the center column,
then insert the column into the base. Screw the hanging hook
into place.
Hanging hook
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising