Cal-Royal 430-P ALUM 400 Series Dual Valve Door in Satin Nickel Installation Manual

Add to my manuals
4 Pages

advertisement

Cal-Royal 430-P ALUM 400 Series Dual Valve Door in Satin Nickel Installation Manual | Manualzz

Installation Instructions

REGULAR ARM INSTALLATION

Closer is installed on PULL/HINGE side of door

TOP JAMB INSTALLATION

Closer is installed on frame on

PUSH/STOP side of door

Surface Mounted

Interior Door Closer

Series: 400

Model: 420-P Size: 2

No Hold-Open/Hold-Open

Optional Back check

PARALLEL ARM INSTALLATION

Closer is installed on PUSH/STOP side of door

Illustration:

Non Hold Open Arm

Left Hand Door - LH or

Right Hand Reverse - RHR

SEE PAGE 2

Illustration:

Non Hold Open Arm

Right Hand Door - RH or

Left Hand Reverse - LHR

SEE PAGE 3

Illustration:

Non Hold Open Arm

Right Hand Door - RH or

Left Hand Reverse - LHR

SEE PAGE 4

CLOSER ADJUSTMENT

CLOSING CYCLE

NOTE: Closing arcs (”CLOSE” and “LATCH”) are controlled by two (2) separate speed valve adjuster.

Adjust the CLOSING speed first, then adjust the LATCHING speed.

1. “CLOSING” speed adjustment is accomplished by full rotations of the speed valve adjuster.

- Turn the speed valve screw CLOCKWISE for a slower close arc closing speed.

- Turn the speed valve screw COUNTER-CLOCKWISE for a faster close arc closing speed.

2. “LATCH” speed adjustment is accomplished by full rotations of the speed adjuster valve.

- Turn the speed valve screw CLOCKWISE for a slower latch arc closing speed.

- Turn the speed valve screw COUNTER-CLOCKWISE for a faster latch arc closing speed.

CAUTION!! Do not turn speed adjuster valve more than two (2) full turns counter-clockwise from its factory

default position, as the two speed valve adjusters could become dislodge from the door closer body,

resulting in the loss of internal fluid and failure of the device.

CLOSING SPEED

LATCHING SPEED

LATCHING

SPEED VALVE

2 1

CLOSING

SPEED VALVE

ILLUSTRATION TO DETERMINE HAND OF DOOR

PULL SIDE PULL SIDE

PUSH SIDE PUSH SIDE

LEFT HAND DOOR RIGHT HAND DOOR

6605 Flotilla St. Commerce, CA 90040 USA

Tel: 800-876-9258; 323-888-6601 ; Fax: 800-222-3316; 323-8886699

Web: www.cal-royal.com ;Email: [email protected]

Series: 400

Model: 420-P

Size: 2

Installation Instructions for REGULAR ARM (PULL SIDE) Mounting

A

5-3/4”

(146mm)

1-9/16” (39.7mm)

1”(25.4mm)

SIZE: 2

Model: 420-P

OPENING

To 120°

120°-180° 3/4”

(19mm)

6-5/8”

(168.3mm)

1-1/4”

(31.75mm)

DIM. A

3-3/4” (95.25mm)

2-9/16” (65mm)

Right hand door shown

Left hand door opposite

Dimensions are in inches

Do not scale drawing

CL

Hinge or

Pivot

INSTALLATION INSTRUCTIONS

1. Select Door opening angle and use dimensions shown above.

Mark four(4) on door for door closer and two(2) holes on frame

for arm shoe.

2. Drill pilot holes on door and frame , #14 all- purpose screws or

drill and tap for 1/4-20 machine screws.

3. Install forearm/arm shoe assembly to frame using screws

provided.

4. Mount closer on door using screws provided. SPEED ADJUSTER

VALVE MUST BE POSITIONED TOWARDS HINGE EDGE.

5. Install main arm to top pinion shaft, perpendicular to door as

shown below, secure tightly with arm screw/washer assembly

provided.

6. Adjust length of forearm so that forearm is perpendicular to

frame when assembled or preloaded main arm (Illustration

below). Secure forearm to main arm with screw/washer

assembly provided.

7. Snap pinion cap over shaft at bottom of closer.8. Adjust closing

speed of door, following instructions as shown in page 1.

OPENING CYCLE

NOTE: These instructions apply only to closers equipped with backcheck.

- To increase backcheck intensity, turn valve marked “BC” clockwise

- To decrease backcheck intensity, turn valve marked “BC”

counter-clockwise.

OPENING CYCLE

Backcheck Range

DECREASE

INCREASE

Backcheck Intensity “BC”

Never close this valve completely

TOP VIEW TYPICAL INSTALLATION

SPEED

ADJUSTER

SCREW

PRELOAD

“BC” ADJUSTING SCREW

PRELOAD

SPEED

ADJUSTER

SCREW

PAGE 2

Series: 400

Model: 420-P

Size: 2

Installation Instructions for TOP JAMB (PUSH SIDE) Mounting

6-5/8” (168.3mm) A

3/4” (19mm)

1/2”

(12.7mm)

1-3/4” (44.4mm)

SIZE: 2

Model: 420-P

OPENING

To 120°

120°-180°

5-3/4”

(146mm)

1-9/16”

(39.7mm)

DIM. A

3-3/4” (95.25mm)

2-9/16” (65mm)

Right hand door shown

Left hand door opposite

Dimensions are in inches

Do not scale drawing

CL Hinge or

Pivot

INSTALLATION INSTRUCTIONS

1. Select Door opening angle and use dimensions shown above.

Mark four(4) on door for door closer and two(2) holes on frame

for arm shoe.

2. Drill pilot holes on door and frame , #14 all- purpose screws or

drill and tap for 1/4-20 machine screws.

3. Install forearm/arm shoe assembly to frame using screws

provided.

4. Mount closer on door using screws provided. SPEED ADJUSTER

VALVE MUST BE POSITIONED TOWARDS HINGE EDGE.

5. Install main arm to top pinion shaft, perpendicular to door as

shown below, secure tightly with arm screw/washer assembly

provided.

6. Adjust length of forearm so that forearm is perpendicular to

frame when assembled or preloaded main arm (Illustration

below). Secure forearm to main arm with screw/washer

assembly provided.

7. Snap pinion cap over shaft at bottom of closer.8. Adjust closing

speed of door, following instructions as shown in page 1.

OPENING CYCLE

NOTE: These instructions apply only to closers equipped with backcheck.

- To increase backcheck intensity, turn valve marked “BC” clockwise

- To decrease backcheck intensity, turn valve marked “BC”

counter-clockwise.

OPENING CYCLE

Backcheck Range

DECREASE

INCREASE

Backcheck Intensity “BC”

Never close this valve completely

TOP VIEW TYPICAL INSTALLATION

SPEED

ADJUSTER

SCREW

PRELOAD

“BC” ADJUSTING SCREW

PRELOAD

SPEED

ADJUSTER

SCREW

PAGE 3

Series: 400

Model: 420-P

Size: 2

Installation Instructions for Parallel Arm (PUSH SIDE) Mounting

1-3/4”

1/2”

A

7/16 ”

2-11/16” (68.26mm)

3/4”

Parallel bracket

SIZE: 2

Model: 420-P

OPENING

To 120°

DIM. A

5-7/8”

(149.2mm)

120°-180°

4-11/16”

(119mm)

DIM. B

4-11/16”

(119mm)

3-1/2”

(88.9mm)

B

3” (76.2mm)

Right hand door shown

Left hand door opposite

Dimensions are in inches

Do not scale drawing

3/4”(19mm)

Hinge or

Pivot

6-5/8”

(168.3mm)

INSTALLATION INSTRUCTIONS

OPEN CYCLE

1. Select door opening angle and use dimensions shown above,

mark four (4) holes on door for door closer and three(3)

holes underside of frame for parallel bracket.

2. Drill pilot holes in door and frame for #14 all-purpose

screws or drill and tap for 1/4-20 machine screws.

3. Mount closer on door using screws provided. SPEED ADJUSTER

VALVE MUST BE POSITIONED AWAY FROM HINGE EDGE.

4 Install Parallel Arm Bracket to frame using screws.

5. Using a wrench on the square shaft at bottom of closer, rotate shaft

approximately 45° toward hinge edge of door. Hold and place main

arm of shaft on top of closer at proper index mark as inllustrated.

NOTE: These instructions apply to closers equiped with backcheck

counter-clockwise

FOR LEFT HAND DOOR “L” (illustration “A”) FOR RIGHT HAND

DOOR “R” (illustration “B”). Tighten arm screw with lockwasher securely.

6. Remove arm shoe from forearm and discard. Install ROD end of

forearm to bracket using screw/washer assembly provided.

7. Adjust length of adjustable forearm so that adjustable forearm is

parallel to frame.

8. Adjust closing speed of door, following instructions as shown in Page 1.

To increase backcheck intensity, turn valve marked “BC” clockwise.

To decrease backcheck intensity, turn valve marked “BC”

Backcheck Range

DECREASE

INCREASE

Backcheck Intensity “BC”

Never close this valve completely

RIGHT HAND DOOR LEFT HAND DOOR index mark

R

L

(A)

“BC” or “DA”

Adjusting Valve

Spring Power

Adjusting NUT

(B)

L index mark

R

PAGE 4

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement