Dynex | DX-TVM111 | User's Manual | Dynex DX-TVM111 User's Manual

Dynex DX-TVM111 User's Manual
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 1 Friday, March 22, 2013 4:12 PM
A S S E M B LY G U I D E
DX-TVM111
TV Wall Mount
Safety information and specifications . . . . . . . . .
Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation instructions . . . . . . . . . . . . . . . . . . . . . . .
For either wood-stud or
concrete wall installations
Before using your new product, please read these instructions to prevent any damage.
2
2
3
4
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 2 Friday, March 22, 2013 4:12 PM
2
DX-TVM111
Safety information and specifications
Safety information and specifications
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any
purpose not explicitly specified by Dynex.
Improper installation may cause property
damage or personal injury. If you do not
understand these directions, or have
doubts about the safety of the installation, contact
Customer Service or call a qualified contractor. Dynex is not
responsible for damage or injury caused by incorrect
installation or use.
The weight of your TV must not exceed 30 lbs. (13.6 kg). The
wall must be capable of supporting five times the weight of
your TV and wall mount combined.
This product contains small items that could be a choking
hazard if swallowed. Keep these items away from young
children!
Maximum TV weight: 30 lbs. (13.6 kg)
Screen size: 13 in. to 26 in. diagonal
Overall dimensions (H × W ):
5.4 × 8.7 in. (13.7 × 22 cm)
Wall-mount weight: 1.7 lbs.
We’re here for you
www.dynexproducts.com
For customer service, call:
800-305-2204 (U.S./Canada markets)
Tools needed
You will need the following tools to assemble your new TV wall mount:
ardware
Level
Edge-to-edge stud
finder
Drill
Pencil
Phillips screwdriver
Socket wrench with
7/16" (11 mm) socket or
adjustable wrench
1/8" (3 mm) wood drill bit for
wood stud wall
OR
1/2" (12 mm) masonry drill
bit (concrete only)
Tape
Measuring tape
Hammer
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 3 Friday, March 22, 2013 4:12 PM
Package contents
DX-TVM111
Package contents
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
A TV Bracket (1)
B Wall Plate (1)
J Wall mount template (1)
B
A
J
TV Hardware Bag
Label
C
D
Hardware
M4 × 12 mm
screw
M4 × 30 mm
screw
Qty.
4
Label
G
F
M4 washer
M4 spacers
Qty.
2
1/4" × 2 1/2" lag bolt
4
H
E
Hardware
Concrete anchor
2
4
4
I
1
Locking bar
3
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 4 Friday, March 22, 2013 4:12 PM
4
DX-TVM111
Installation instructions
Installation instructions
STEP 1 - Determine wall-mount location
Notes:
• For more detailed information on determining where to drill your holes, visit our online height-finder at:
http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder
• Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the
ground.
The center of your TV will match the center of the wall plate (B). Before you drill holes in the wall:
1 Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is
measurement a.
2 Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall. Keep in
mind that the bottom of the TV should be placed above any furniture (such as entertainment centers or TV
stands). The TV should also be above items placed on top of the furniture (like a Blu-ray player or cable box).
This measurement is b.
3 Add a + b. The total measurement is the height where you want the center of the wall plate (B) to be on the
wall.
4 Use a pencil to mark this spot on the wall.
a
b
You’ll need
Measuring tape
Pencil
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 5 Friday, March 22, 2013 4:12 PM
Installation instructions
DX-TVM111
5
STEP 2 - Option 1: Installing on a wood stud* wall
Note: Any wallboard or material covering the wall must not exceed 5/8" (16 mm).
1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.
2 Align the wall plate template (J) at the height you determined in the previous step and make sure that it is
level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).
Remove the wall plate template.
3 Drill pilot holes to a depth of 3 in. (75 mm) using a 1/8" (3 mm) wood drill bit.
4 Align the wall plate (B) with the pilot holes, insert the lag bolts (G) through the holes in the wall plate, then
tighten the lag bolts only until they are firm against the arm assembly.
CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the lag bolts (G).
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm)
nominal 11/2 x 31/2 in. (38 x 89 mm).
3 in.
(75 mm)
You’ll need
DX-TVM111
Template • Gabarit • Plantilla
Top
Haut
Parte superior
Tools Needed
Outils nécessaires
Herramientas requeridas
G (2)
Note
Remarque : Pour une construction à ossature de bois,
localiser d'abord les montants en bois, à l'aide d'un
détecteur de montants.
Nota: para la instalación en construcciones de armazón de
madera, primero debe localizar las vigas de madera con un
localizador de vigas.
Pencil
Need more information about your mount? Scan
this QR code or visit www.dynexproducts.com.
<FR>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
<SP>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
Edge-to edge
stud finder Template (J)
http://san.us/284
Level
Wall plate (B)
Drill
V1 13-0138
Tape
1/8" wood
drill bit
7/16" socket
wrench
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 6 Friday, March 22, 2013 4:12 PM
6
DX-TVM111
Installation instructions
STEP 2 - Option 2: Installing on a solid concrete* or concrete block wall
CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount wall plate
directly onto the concrete surface.
1 Align the wall plate template (J) at the height you determined in the previous step and make sure that it is
level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).
Remove the wall plate template.
2 Drill pilot holes to a depth of 3 in. (75 mm) using a 1/2 in. (12 mm) diameter masonry drill bit.
3 Insert the concrete wall anchors (H) into the pilot holes and use a hammer to make sure the anchors are flush
with the concrete surface.
4 Align the wall plate (B) with the anchors, insert the lag bolts (G) through the holes in the wall plate, then
tighten the lag bolts only until they are firm against the wall plate.
CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the lag bolts (G).
* Minimum solid concrete thickness: 8 in. (203 mm)
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
3 in.
(75 mm)
You’ll need
DX-TVM111
Template • Gabarit • Plantilla
Top
Haut
Parte superior
Tools Needed
Outils nécessaires
Herramientas requeridas
G (2)
Level
Note
Remarque : Pour une construction à ossature de bois,
localiser d'abord les montants en bois, à l'aide d'un
détecteur de montants.
Nota: para la instalación en construcciones de armazón de
madera, primero debe localizar las vigas de madera con un
localizador de vigas.
Need more information about your mount? Scan
this QR code or visit www.dynexproducts.com.
<FR>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
<SP>Need more information about your mount?
Scan this QR code or visit www.dynexproducts.com.
http://san.us/284
H (2)
Drill
Template (J)
Wall plate (B)
1/2" masonry
drill bit
Pencil
V1 13-0138
Hammer
Tape
7/16" socket
wrench
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 7 Friday, March 22, 2013 4:12 PM
Installation instructions
DX-TVM111
7
STEP 3 - Determine whether your TV has a flat, irregular, or obstructed back
1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages
and scratches.
2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV
for instructions.
3 Temporarily lay the TV bracket (A) on the back of your TV.
4 Align the screw holes in the TV bracket with the mounting screw holes on your TV.
5 Identify which type of back your TV may have:
• Flat back: The bracket lays flush against the back of your TV and do not block any jacks. You do not need spacers when
assembling the wall mount.
• Obstructed back: The bracket blocks one or more of the jacks on the back of your TV. You will need spacers when
assembling the wall mount.
• Irregularly-shaped back: There is a gap between the bracket and some part of the back of your TV. You will need
spacers when assembling the wall mount.
6 Remove the TV bracket (A).
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 8 Friday, March 22, 2013 4:12 PM
8
DX-TVM111
Installation instructions
STEP 4 - Select screws, washers, and spacers
1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting
hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back
of the TV.)
Select one of the following types of screws:
M4 × 12 mm screws (C) for a flat back TV.
M4 × 30 mm screws (D) for an irregular or obstructed TV back.
For an irregular or obstructed TV back, use the following spacers:
Universal spacers (F)
Screw fits
correctly
Screw is
too long
CAUTION: To avoid potential personal injuries and
property damage, make sure that there are adequate threads
to secure the brackets to your TV. If you encounter resistance,
stop immediately and contact customer service. Use the
shortest screw and spacer combination to accommodate your
TV. Using hardware that is too long may damage your TV.
However, using a screw that is too short may cause your TV to
fall from the mount.
Screw is
too short
2 Remove the screws.
3 For a flat back TV, go to “STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on
page 9.
-ORFor an irregular or obstructed back, go to “STEP 5 - Option 2: Attaching the mounting hardware to TVs with
irregular or obstructed backs” on page 10.
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 9 Friday, March 22, 2013 4:12 PM
Installation instructions
DX-TVM111
STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back
1 Align the TV bracket (A) with the screw holes on the back of the TV.
2 Install washers (E ), and screws (C) into the top two holes in the back of the TV.
NOTE: If the hole pattern on your TV is 75 mm x 75 mm, do not use the washers (E).
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
You’ll need
Screws
C (4)
Washers
Phillips screwdriver
E (4)
TV bracket (A)
9
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 10 Friday, March 22, 2013 4:12 PM
10
DX-TVM111
Installation instructions
STEP 5 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed
backs
1 Align the TV bracket (A) with the screw holes on the back of the TV.
2 Place spacers (F) behind the TV bracket and the washers (E) over the holes in the TV bracket, then insert the
screws (D) through the washers, TV bracket, and spacers.
NOTE: If the hole pattern on your TV is 75 mm x 75 mm, do not use the washers (E).
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
You’ll need
Screws
D (4)
Washers
Spacers
Phillips screwdriver
E (4)
F (4)
TV bracket (A)
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 11 Friday, March 22, 2013 4:12 PM
Installation instructions
DX-TVM111
11
STEP 6 - Mounting the TV to the wall plate
• Place the TV bracket (A) into the slotted flanges of the wall plate (B). The TV can be mounted either (1) vertically, or (2)
with a 5° tilt.
HEAVY! You will need
assistance with this step.
1 - Vertical mount
Note: Attach the TV bracket to the flange that is closest to the wall plate.
2 - Tilt mount
Note: Attach the TV bracket to the flange that is farthest from the wall plate.
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 12 Friday, March 22, 2013 4:12 PM
12
DX-TVM111
Installation instructions
STEP 7 - Locking the TV to the wall plate
• Slide the locking bar (I) through the TV bracket (A) and the wall plate (B) to secure the TV. A padlock (not included) may
be used for extra security.
Vertical mount
Tilt mount
You’ll need
Locking bar (I)
DX-TVM111_12-1055_MAN_V1_ENG - GIF.fm Page 13 Friday, March 22, 2013 4:12 PM
www.dynexproducts.com (800) 305-2204
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2013 BBY Solutions, Inc. All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
6907-002009 <02>
V1 ENGLISH 12-1055
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising