1) Characteristics

• Power supplied by three 1.5 V alkaline batteries of type LR03 or AAA (last for more than 1 year)

• Battery replacement indicator

• Insulation class III

• Mode selector switch (7 positions)

• Choice of 3 permanent temperature settings - Frost protection, Night-time temperature, Daytime temperature - and one user-programmable cycle per day

• The 3 temperature settings can be programmed as follows : between 5° and 30°C for Night-time and Daytime temperatures and between 5° and 15°C for Frost protection

• Proportional-plus-integral control (category B), time base 15 min

• Stand-by mode

• Transmission frequency : 433 MHz

(Standard I-ETS 300 220)

• Average range between transmitter and receiver :

100m outside, 30m inside.

• Addresses: 65536 combinations

• Digital display

• Enclosure dimensions: 128 × 85 × 31 mm

• Wall mounting or on base

• Degree of protection: IP 30

This system is incompatible with items of wireless equipment which operate on the same frequency band (433 MHz), in permanent transmission mode

(headphones, wireless loudspeakers...) as they may interfere with the signal.

2) Installation

2.1Choice of location

2.1.1 Radio transmission

The location of the thermostat should be chosen carefully as some furnishings could absorb or reflect the radio transmissions.

We therefore advise that the mode of transmission and the quality of reception is checked last (§ 3.4).

2.2 Mounting

2.2.1 Wall mounting

In order to mount the thermostat on the wall, it must be separated from its base, as shown in figure 1.

The base is then fixed to the wall using screws and plugs or on a flush-mounting box (centre-tocentre distance 60 mm) using the holes ➊.

2.1.2 Temperature measure

The thermostat must be positioned correctly. The recommended height is 1.5 m in an accessible place, away from heat sources (fireplace, sunlight) and draughts

(window, door).

2.2.2 Base mounting

The thermostat has a foldaway base and can be used away from its wall mounting. For example it can be placed on a table or other furniture. It must be remembered that its location could have an effect on the transmission of the radio signals and that it must be kept away from direct heat sources and draughts (§ 2.1).

1,50 m

Mini 20 cm

If the thermostat is mounted on its base, it can be used as a real heating remote control and so you can take it with you wherever you are.

WARRANTY

This thermostat is guaranteed for t hree years from its date of delivery.

To benefit from this guarantee, a proof of purchase bearing the date of acquisition must be enclosed with your faulty thermostat when you return it.

The guarantee covers replacement of faulty parts, labour, and return shipping to the customer.

The following are excluded from the guarantee :

- thermostats whose serial numbers have been damaged, altered or erased,

- thermostats whose installation or use did not conform to the instructions given on the device or in the manual,

- thermostats modified without prior agreement from the manufacturer,

- thermostats damaged by impacts.

3) Set up

3.1Battery installation

Your thermostat is powered by three 1,5V alkaline batteries, type LR03 or AAA.

See user guide on the back (§ 5).

3.2Time setting

See user guide on the back (§ 6) .

3.3 Programming / Reprogramming

In the programming mode, every receiver can be allocated a transmitter. (When extending your system, it is possible to program several receivers to one transmitter without any problems). Additionally, this mode is also used for checking the transmitting quality.

➊ Turn the transmitter's selector switch to the

➋ Press the button

(3 sec.) until CnF appears on the display.

position

The transmitter sends its data to the receiver

➌ Receiver :

• If the green pilot lamp (OK) lights up continuously, the receiver has already been programmed.

To reprogram, keep the button pressed for 10 seconds until the green "OK" lamp starts to flash slowly, then release it.

Press the button on the receiver again.

The green "OK" lamp lights up continuously, the receiver has been reprogrammed.

• If the green pilot lamp (OK) flashes slowly, the receiver has not been programmed.

Press the button on the receiver again. The green

"OK" lamp lights up continuously, the receiver has been reprogrammed.

3.4 Checking the quality of transmission

➊ Turn the transmitter switch to the position.

➋ Press the display.

button (3 sec.) until tESt appears on the

The transmitter sends its data to the receiver.

➍ Press the key on the transmitter to leave programming mode. The receiver's output executes the transmitter's command.

The red pilot lamp

On = Contact indicates the state of the contact.

Off = No contact

The green OK lamp flashes 3 times every time data is received correctly.

➌ Press the button to leave transmission test mode.

3.5 A Problem?

The green "OK" lamp is flashing (the receiver has not received any data for more than an hour).

1) Check the batteries in the transmitter

2) Enter transmission test mode

- If the green "OK" lamp does not flash (3 times) every time data is received move the transmitter to another position

- If the problem continues, reprogram both devices.

Equipment conforming to the requirements of directives

CEE 89/335 (Electromagnetic Compatibility) and CEE 73/23 amended by CEE 93/68 (Low voltage safety).

4) Description

1 1

1 5

7.4 Temperature display

Press the key.

The thermostat displays four dashes.

1 2

5) Fitting the batteries

Three 1.5 volt alkaline batteries of type LR03 or AAA

(last for more than 1 year).

Do not use rechargeable batteries.

0h 2 4 6 8 10 12 14 16 18 20

22 24

6) Time setting

1 3

Press time.

Turn the selector switch to the or to adjust the

1

2

3

4

5

6

7 position.

The day changes after every 24 hours.

Pressing briefly : advances the time in minute increments

Press and hold : Fast forward

Nota : When adjusting the hour, the heating is OFF.

Fig. 3 Fig. 4

To replace used batteries, remove the thermostat from its base. Insert new batteries making sure that they are fitted the right way round. Then replace the thermostat on its base.

Battery replacement

When the battery replacement indicator appears, the batteries in the thermostat are flat and must be replaced. Never leave flat batteries in the device (the warranty does not cover damage caused by leaking batteries).

New batteries must be fitted within approx. 1 minute to ensure that the programmed information is not lost.

1 4

7) Temperature settings

7.1 Setting the Frost-protection temperature

Default setting : 7 °C

➊ Turn the selector switch to

➋ Press or to adjust the temperature

(between 5 and 15 °C)

7.2 Setting the Economy temperature

Default setting : 16 °C

➊ Turn the selector switch to

➋ Press or to adjust the temperature

(between 5 and 15 °C)

7.3 Setting the Comfort temperature

Default setting : 19 °C

➊ Turn the selector switch to

➋ Press or to adjust the temperature

(between 5 and 15 °C) http://www.deltadore.com

Fax : 33 (0)2 99 73 44 87 l. : 33 (0)2 99 73 45 17 Té

35270 COMBOURG (France)

Bonnemain

1 6

8) Weekly programming

8.1 Define your weekly programming

You have 4 preset programs. You can select one of them by turning the selector switch.

Permanent Frost protection

(adjustable from 5 to 15 °C)

4

5

6

7

1

2

3

Permanent

Comfort

(adjustable from 5 to 30 °C)

A

U

T

O

Permanent

Economy

(adjustable from 5 to 30 °C)

At the first use,

Comfort from 6 a.m to 23 p.m for each day of the week.

5

6

7

1

2

3

4

0h 2 4 6 8 10 12 14 16 18 20 22 24

4

5

6

7

1

2

3

0h 2 4 6 8 10 12 14 16 18 20 22 24

4

5

6

7

1

2

3

0h 2 4 6 8 10 12 14 16 18 20 22 24

You can modify this program.

1 7

8.2 Modifying and validating your program

P

R

O

G

– Switch the selector to PROG

The temperature display disappears and you can see the program for the first day.

The first time slot flashes.

— Press for 1 hour of Comfort or for 1 hour of

Economy (The second time slot flashes))

Repeat the same procedure for each time slot.

˜ Press immediately following day.

to validate and to access to the

Repeat the operations ➋ and ➌ for each day.

™ After programming, switch the selector on AUTO.

Note : For modes , and AUTO, the displayed temperature is the temperature setting for the current time period.

e.g. Day 3, it is 8.15 p.m.

The corresponding time period

5

6

7

1

2

3

4 blinks. The comfort temperature is programmed, so its value is displayed.

0h 2 4 6 8 10 12 14 16 18 20 22 24 or Day 3, it is 4.20 a.m.

The Economy temperature setting is displayed.

1

2

3

4

5

6

7

0h 2 4 6 8 10 12 14 16 18 20 22 24

1 8

9) Heating shutdown

- Stand-by mode

The thermostat is switched to stand-by mode in periods when heating is not required.

Switch the selector to position .

The thermostat displays four dashes.

10) A Problem?

The

Nothing is displayed on the screen.

Problem symbol appears.

Diagnosis / Solutions

• The batteries are discharged.

Replace the batteries (see p. 12)

• No power supply

- 230V mains model : check the 230V power supply

- battery model : replace the batteries or check their polarities (direction)

The whole display is blinking

The Micro-TYBOX has just been switched on.

Check and if necessary adjust the clock and the temperatures, otherwise press a key.

Micro TYBOX H

RADIO X2D

Wireless week-day programmable room thermostat

3

4

5

1

2

6

7

0h 2 4 6 8 10 12 14 16 18 20 22 24