LIGHT AND EASY LED-0808 User Guide
LIGHT AND EASY
LED-0808
User Guide
Please read these instructions carefully before use
1B
CONTENTS
1. Features ................................................................................................ 3
2. General Instruction..................................................................................4
3. Overview .................................................................................................5
3.1 Front View ............................................................................................. 5
3.2 Rear View.............................................................................................. 6
4. Operation Guide......................................................................................6
4.0 Channel Asignment……………………………………………………..…6
4.1 Store Saved Colours .............................................................................8
4.2 Delete Saved Colours ...........................................................................7
4.3 Program Chase .....................................................................................9
4.4 Insert step to Chase ..............................................................................8
4.5 Delete Step From Chase ......................................................................9
4.6 Delete Chase ...................................................................................... 11
4.7 Factory Reset...................................................................................... 10
4.8 Manual Mode ...................................................................................... 12
4.9 Run Saved Colours .............................................................................10
4.10 Run CHASE ...................................................................................... 14
4.11 Run Pre Set Colours…………………………………………………….12
4.12 Over control ...................................................................................... 15
4.13 Strobe ................................................................................................ 16
4.14 Blackout .......................................................................................... 16
4.15 Foot Switch (CA-8F) .........................................................................16
4.16 Update by USB driver .......................................................................16
2B
1. Features
1. Light and Easy is a user friendly LED controller.
2. Designed to work on all 8-Channel LED lighting fixtures
3. Control up to 64 channels of 8 LED groups
4. 8 individual buttons for selecting 8 groups of lighting fixtures
5. LED display for easy navigation
6. 8 Color pre-set buttons
7. 6 saved colour with 4 Banks.
8. 8 Chases, each can save up to 32 steps.
9. 3 operation modes:Auto Chase, Sound Chase, Manual Control.
10. Optional Foot Controller (CA-8F) for ease of operation.
NOTE:
A knowledge of DMX is required to fully utilize this unit.
3B
2. General Instruction
Please read the user manual carefully, as it includes important information regarding
details of operation, maintenance, and technical data. Keep this manual with the unit for
future consultation.
WARNINGS!

Avoid any inflammable liquids, water or metal objects entering the unit.

Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit

STOP using the unit immediately In the event of serious operation problems and

DO NOT open the unit--there are no user serviceable parts inside.

NEVER try to repair the unit yourself. Repaired by unqualified people could cause
immediately.
contact your local dealer for a check immediately.
damage or malfunction.
CAUTIONS!

After removing the packing Make that the unit is NOT damaged in any way. If in doubt,

Packaging material (plastic bags, polystyrene foam, nails, etc.) MUST NOT be left

This unit must only be operated by adults. DO NOT allow children to tamper or play

NEVER use the unit under the following conditions:
DON'T use it and contact an authorized dealer.
within children's reach, as it can be dangerous.
with it.
In places subject to excessive humidity.
In places subject to vibrations or bumps.
In places with a temperature of over 45℃/113℉ or less than 2℃ /35.6℉.

Protect the unit from excessive dryness or humidity (ideal conditions are between 35%

DO NOT dismantle or modify the unit.
and 80%).
4B
3. Overview
3.1 Front View
1. FIXTURE SELECTOR 1-8
use to select fixtures
2. AUTO CHASE
To run the chase automatically
3. SOUND CHASE
Run the chase to the music
4. AUTO FADER
5. MANUAL CONTROL
Press the button, you can turn to Manual control
6. CHANNEL ASSIGNMENT
Channel assignment
7. USB PORT
Use to update and connect with gooseneck lamp
8. PRESET COLOURS
Setting p,
9. SAVED COLOURS
Select 24 colors by UP/SOWN button
10. LED DISPLAY
The operation states will show on the LED display
11. PROGRAM/RECORD
enter or exit program/record
12. INSERT/TAP
Insert one step/set up a tap for chase
13. UP/DOWN button
Select bank, run chase manually, adjust the sound
sensitivity and the times chase auto run
5B
14. DEL/CLEAR
delete preset color, chase or step/clean output
15. SAVED CHASES
use to select chase 1-8
16. FADER 1-6
adjust the output of 1-8 channels
17. USER DIFINITION FADER
Keep for user-defined
18. MANUAL/MUSIC/AUTO
When using the CA-8 to control, the corresponding
LED on indicating Manual Mode, Sound Mode or
Auto Mode.
19. BLACKOUT/FOOTSWITCH
Blackout/change to the footswitch control status
20. STROBE
strobe
21. CHASE SPEED
Use to adjust the chase speed
22. FADER SPEED
use to adjust the fade speed which show as
percentage of the run time
3.2 Rear View
①
②
③
④
○
5
○
6
POWER SWITCH
POWER IN
3pin DMX Out
5pin DMX Out
RJ45 CONNECTOR
CA-8F FOOT CONTROLLER
Power on/off the unit
9-12DC min 300mA
3 pin DMX-512 output
5pin DMX512 output
RJ 45 Cable port
CA-8F connector
4
4. Operation Guide
Turn on the power, the controller access to the last control status of
LED-0808 or CA-8F. Press BLACKOUT/FOOT SWITCH button to
switch to LED-0808 or CA-8F control. Follow functions will be
available under LED-0808 controlling.
1、CP1.1-CP4.6
2、CAS1-CAS8
Saved colour, 4 banks, each bank with 6 saved colour
chase
6B
chase step
data
chase speed (the interval time between two steps)
3、ST01-ST32
4、D000-D255
5、0.1 /08.8
(1) one digital after radix point: the unit is second
21.30 /60.00
(2) Two digital after radix point: the digital before
radix point is minutes, and the digital after radix
point is seconds.
fade time: the percent of the chase speed
sound sensitivity
loop
null
Lock
6、P000---P100
7、M001-M100
8、L001-L200
9、NULL
10、LOCH
4.0 Channel Assignment
Enter programming mode: Hold PROGRAM/REC button for 3 seconds,
when the LED display shows “LOCK”, you should press
fixture selector button 6 for six times to unlock. That means the code is
“666666”. Then the PROGRAM/REC button and the LED indicator above the
saved colors button as well as the saved chases button will flash indicating
program is active.
1.
Enter programming mode
2.
Press CHANNEL ASSIGNMENT button for 3 seconds, the
LED indicator above bright indicating the program is active.
3.
4.
Press FIXTURE SELECTOR 1-8 button to choose fixture units.
Push FADER 1-8 to assign the color for each channel (1-8), that
all depends on the channel of the light. For example, if the first
channel of light is blue, then you should push the third fader
blue on the position of one, at the same time the display above
the fader will show the number ”1” on it.
7B
5.
Pressing the PROGRAM/REC button, the all LED indicator
flash for 3 times and then go out indicating that has already
stored in it successfully.
6.
Repeat steps 3-5 to assign all other color for the channel of the assigned lights.
Note:
The value of the fader is 0 to 8, and then 1 to 8 means the channels which
you will assign for the fixtures. The value “0” that means you will turn off the channel
output. After you finish your setting for the channel turn on/off just press the
PROGRAM/REC button once then all the light will flash for 3 times, that means you
have saved the setting successfully.
7.
Hold CHANNEL ASSIGNMENT button for 3 seconds to exit the channel assignment
mode, and the LED indicator above it will be off. Or hold PROGRAM/REC button for
3 seconds to exit programming mode.
4.1 Store Saved Colour (Scene)
1
Enter programming mode.
2
Press FIXTURE SELECTOR 1-8 button to choose units.
3
Push fader FADER 1-8 to adjust the output.
4
Press PROGRAM/REC button.
5
Press UP/DOWN button to choose bank 1-6 to store saved color
(Jump this step if you have chosen a bank before).
8B
6
Press SAVED COLOURS button, all LED indicator flashing for 3
times and then go out, the corresponding LED flashing
indicating that has already stored successfully (when the LED
indicator off, means there is null color saved).
7
Repeat steps 2-6 to store more saved color.
8
Hold PROGRAM/REC button for 3 seconds to exit programming mode, the LED
indicator above PROGRAM/REC will be off.
9
4.2 Delete saved Color (Scene)
1
Enter programming mode.
2
Use UP/DOWN button to choose bank 1-6 the saved color
(Jump this step if you have chosen bank before).
3
Hold DEL/CLEAR button, press SAVED COLOURS 1-6, all LED
flashing for 3 times and then go out, the corresponding LED off
indicating the saved color have deleted successfully.
4
Repeat 2-3 steps to delete more color presets.
5
Hold PROGRAM/REC button for 3 seconds to exit programming
mode, the LED above PROGRAM/REC button will be off.
4.3 Program Chase
1
2
Enter programming mod.
Press CHASE 1-8 button to choose chase which
desired to store in.
3
Press FIXTURE SELECTOR 1-8 button to choose units, pushing
fader 1-8 to adjust the light effect, or open a saved color stored.
4
Press PROGRAM/REC button, all LEDs flashing for 3 times and then go out
9B
indicating that one step has stored successfully ( it will show “NULL” and do not store
if all outputs are ”0” ).
5
Repeat steps 3-4 to store more steps, each chase 32 steps maximum, it will show
“FULL” when up to 32 steps.
6
Repeat steps 2-5 to store more chases.
7
Hold PROGRAM/REC button for 3 seconds to exit programming
mode, the LED indicator above PROGRAM/REC will be off.
ATTENTION: Before using any saved color or lighting effect, press DEL/CLEAR button
to clean the output you set inadvertently, so that you can avoid storing the lighting effect
that unwished.
4.4 Insert step to Chase
1
Enter programming mode.
2
Press CHASE 1-8 button to choose the chase desired to insert
step.
3
Press INSERT/TAP button, the LED indicator above it will on, the
present step will show on the display (for example, it will show
“ST00” when there is no step).
4
Use UP/DOWN button to select the position of inserted steps ( If
you want to insert fifth step, you should set the present step to be
“ST05”).
5
Press FIXTURE SELECTOR 1-8 button to choose units, use
UP/DOWN button to choose saved color or push the FADER 1-8
to adjust the lighting effect.
10B
6
Press PROGRAM/REC button, all LEDs flashing for 3 times and
then go out indicating it succeed in inserting one step.
7
Repeat steps 3-6 to insert more steps, 32 steps maximum,
exceeding this it will show “FULL”.
8
Hold PROGRAM/REC button for 3 seconds to exit programming mode, the LED
indicator above ROGRAM/REC will be off.
4.5 Delete Step From Chase
1
Enter programming mode.
2
Press CHASE 1-8 button, choose the chase whose step desired
to delete.
3
Press INSERT/TAP button, the LED indicator above it will light up,
the present step show on the display (it will show “ST00” if none
step has been stored).
4
Press UP/DOWN button to choose the step desired to delete ( if
you want to delete the fifth step, set the present display to “ST05”).
5
Press DEL/CLEAR button, all LEDs flashing for 3 times and then
go out indicating it has been deleted successfully. (The steps
behind it will move forward one step, for example, if you delete the
fifth step, the sixth step will move to be the fifth step. If there is none step behind the
step deleted, it will show the last step. Delete all steps, and then it will show “NULL”.)
6
Repeat steps 4-6 to delete more steps.
7
Hold PROGRAM/REC button for 3 seconds to exit programming
mode, the LED indicator above PROGRAM/REC will be off.
4.6 Delete Chase
1
Enter programming mode.
2
Hold DEL/CLEAR button, and press one of the CHASE 1-8 button.
11B
All LEDs flashing for 3 times and then go out, the corresponding LED indicator
off indicating deleted successfully.
3
Repeat steps 2-3 to delete more chases.
4
Hold PROGRAM/REC button for 3 seconds to exit programming
mode, the LED indicator above PROGRAM/REC will be off.
4.7 Factory Reset
Be careful, factory reset will delete all the settings!
1
Turn off the power.
2
Press the PROGRAN/REC and DEL/CLEAR button at the same
time, turn on the power, wait until all LEDs flashing, release the
buttons,
the
LEDs
stop
flashing
indicating
factory
reset
successfully.
4.8 Manual Mode
1
Insure the LED above the BLACK OUT button is off.
2
Press FIXTURE SELECTOR 1-8 button to choose units desired.
3
Push FADER 1-4 to adjust the effect.
ATTENTION: The LED which besides FIXTURE SELECTOR button on
indicating the corresponding units could be controlled by faders; you can delete the setting
that you do not want to store by pressing DEL/CLEAR button.
4.9 Run Save Colours
1
Insure the LED above the BLACK OUT is off.
2
Use UP/DOWN button to choose BANK 1-6 which stored the
SAVE COLOURS.
12B
3
Press saved colour1-6 button to run SAVED COLOURS.
4.10 Run CHASE
Be sure there are CHASES stored. Press CHASE 1-8 buttons to
run CHASE directly, the correspond LED will be on. If you choose
more than one CHASE at a time, then the first correspond LED will be on
and others will flashing (1Hz), all the CHASE will cycle run one by one.
There are three modes: Manual Mode, Sound Mode and Auto mode.
A. Manual mode
1
Insure the LED above BLACK OUT button is off.
2
Press CHASE 1-8 button to run the CHASE, the display will
show the present CHASE.
3
Press MANUAL/MUSIC/AUTO button to choose Manual Mode,
the MANUAL LED on indicating into Manual Mode.
4
Press UP/DOWN button to change the step, UP to the last step,
DOWN to the next step.
B. Sound Mode
1
Insure the LED above BLACK OUT is off.
2
Press CHASE 1-8 button to run the CHASE, the display will
show the present CHASE.
3
Press MANUAL/MUSIC/AUTO button to choose Sound
Mode, the MUSIC LED on indicating Sound Mode.
13B
4
Press UP/DOWN button to adjust the sound sensitivity, the
CHASE will run to the music.
C. Auto mode
1
Insure the LED above BLACK OUT button is off.
2
Press CHASE 1-8 button,the display will show the present
CHASE.
3
Press MANUAL/MUSIC/AUTO button to choose Auto Mode,
the AUTO LED on indicating Auto Mode.
4
Push CHASE SPEED fader to adjust the CHASE speed, push
FADE SPEED to adjust the fade time (the percent of the chase
speed). Press UP/DOWN button to set the run time for CHASE
(It’s useful when you run more than one CHASE at one time).
You can also change the CHASE speed via INSERT/TAP
button. When running the CHASE, press the INSERT/TAP
button and the indicator will flashing, then press the
INSERT/TAP button and the indicator off, the flashing time will
be the CHASE speed.
4.11 Run Pre Set Colours
Please note that before running the Pre Set Colors ensure the procedure 4.0 channel
assignments have been finished, or it will result in the invalidation of the following operation.
There are three modes: Auto mode, Sound Mode, Auto Fade. Before choose the three
modes, you should select fixtures first, otherwise, the buttons will be unavailable.
A. Auto Chase Mode
14B
1
Insure the LED indicator above BLACK OUT is off.
2
Press AUTO CHASE button, the LED indicator above it on
indicating that has switched to the Auto Mode.
3
Press PRE SET COLOUR1-8 button, all the CHASE will run
one by one circularly.
4
Press CHASE SPEED to adjust the CHASE speed.
B. Sound Mode
1
Insure the LED indicator above BLACK OUT is off.
2
Press SOUND CHASE button, the
LED indicator on
indicating that has switched to the Sound Mode.
3
Press UP/DOWN button to adjust the sound sensitivity, the
CHASE will run to the music.
C. Auto Fade mode
1. Insure the LED indicator above BLACK OUT is off.
2. Press AUTO FADE button, the LED indicator above it on indicating that has
switched to the Auto Fade Mode.
3. Press PRE SET COLOUR1-8 button, all the CHASE will run one by one circularly.
4. Press FADER SPEED to adjust the fade time (the percent of the chase
speed).
4.12 Over control
It can manually control this units when running COLOUR PRESET or CHASE.
1
Ensure the LED indicator above BLACK OUT is off.
2
Run COLOUR PRESET or CHASE directly.
3
Press FIXTURE SELECTOR 1-8 button to choose units.
15B
4
Push FADER 1-8 to adjust the lighting effect, the changes of the channel values
are in dependent on the COLOUR PRESET or CHASE.
5
Back to the normal mode, please press DEL/CLEAR button.
4.13 Strobe
Hold Strobe button, all the light will strobe, and at this time you can adjust the
strobe speed by pressing the Strobe speed Fader.
4.14 Blackout
Press Blackout button, the LED indicator above it will light up, that means you have already
entered into the Blackout mode.
When you hold the Blackout button for about 3 seconds, the LED indicator above it will flash,
that means you have entered into the Foot Switch (CA-8F) Mode. At this time, on this unit
panel only the Dimmer Fader can be used to adjust the total lighting intensity, any other
button on the panel will deactivated. You can use the foot switch (CA-8F) to control the
LED-0808.
4.15 Foot Switch (CA- 8F)
LED-0808 can work with CA-8F, when the CA-8F connected with the LED-0808, hold the
BLACKOUT/FOOT SWITCH button for 3 seconds and the LED indicator above it flashing
that means the CA-8F has already been activated.
1.
STANDBY button used to active the CA-8F or interrupt the connection. Holds it
for about 2 seconds, the LED indicator will go out, then CA-8F have been active.
2.
MODE button used to switch the mode, pressing it, when the LED indicator
beside it light up but not flashing that means it has entered into the chase mode,
pressing the FUNCTION button can change the chase.
3.
When pressing the MODE button till to the indicator beside it light up and flash,
16B
that means it has entered into the step mode, pressing the FUNCTION button
can change the step and the number of step will display on the screen.
4. When pressing the MODE button till to the indicator beside it goes out. Then you
press the FUNCTION button, all the fixtures’ channels will be on 255. That
means all light up.
5.
When you activate the CA-8, all the function buttons on the LED-0808 are
deactivated, except the master dimmer.
CA-8F
4.16 Update by USB drive
Power off the unit, and then insert the USB drive with the specific program in it. Hold
Program/REC button, DOWN button and MANUAL/MUSIC/AUTO button simultaneously,
then power on the unit, when all the lights light up, you can release the button now. The LED
display will show “USB-LINK”. The program will update automatically, after it finish the
update, the LED display will show “UPDAP OK”. You restart the unit and the unit has been
updated successful.
4.17 Upload the files to the USB memory
1. Insert the USB memory to the controller.
2. Hold Bank UP button and MANUAL/MUSIC/AUTO button at the same time to enter
into the upload mode. The LED display will show LOAD on it. That means there is no USB
memory inserted to the controller. Then you insert the USB memory to the controller, the
LED display will show UP F (upload files) on it. The left button 1-8 will light up if there are
some files in the USB memory. Then you press any of the 1-8 buttons to upload the files into
the USB memory automatically. All the files will pack up into one files to store into the USB
memory (If you press the button which is light up that the before files stored in the USB
memory will be recovered). After it finishes the upload, the LED display will show OK on it
17B
and the controller will exit the upload mode.
4.18 Download the files to the controller from the USB memory
1. Insert the USB memory to the controller.
2. Hold Bank Down button and MANUAL/MUSIC/AUTO button at the same time to enter
into the download mode. The LED display will show DL F (down load files) on it. The left
button 1-8 will light up if there are some files in the USB memory. Then you press any of the
light up button to download the files to controller automatically. All the files will download to
the controller now. After it finishes the upload, the LED display will show OK on it and the
controller will exit the down load mode.
NOTICE:The format of the memory disk should be FAT16 or FAT32.
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55103-1:199601-2; EN55103-2:1996;
EN61000-3-2:2000+A2:2005;
EN61000-3-3:1995+A1:2001+A2:2005.
&
Harmonized Standard
EN 60598-1: 2004
IEC 60598-1:2003+ corrigendum 2004
Part 1:General requirements and test
Following the provisions of the low voltage directive 73/23/EEC and 93/68/EEC
18B
Technical Specification
Power Input .................…………………….……..…...9-12 DC min 300mA
DMX Output ..................………………..3/5 pin DMX outpur and RJ45 port
Dimensions.....................……………….........……….280 x 170 x 66 mm
Weight......... ...................……............ ......................1.8 kgs
Innovation, Quality, Performance
19B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement