Electro-Voice SP12C, SP8C, 12C, 15A User manual

Electro-Voice SP12C, SP8C, 12C, 15A User manual
 SPECIFICATIONS
Frequency Response in Recommended
Vented Enclosure, 1 Meter on Axis,
Half Space Anechoic Environment,
Swept One-Third Octave Random
Noise, + 6 dB.
SPBC — 41-12,000 Hz
SP12C — 37-10,000 Hz
SP15A — 34-8,000 Hz
Low-Frequency Acoustic Power Output
vs. Frequency, Small Signal, in
Recommended Vented Enclosure
3-dB-Down 10-dB-Down
SPEC — 560 Hz SP8C — 36 Hz
SP12C — 43 Hz SP12C — 32 Hz
SP15A — 40 Hz SP15A — 30 Hz
Sound Pressure Level at 1 Meter, 1 Watt
into Nominal Impedance, Anechoic
Environment, 300-2,000 Hz Average
SPBC — 95 de
SP12C — 100 dB
SP15A — 103 dB
Power Handling Capacity,
Long-Term Average Short-Term (10 mis)
SPEC — 26 watts SPBC — 250 watts
SP12C — 75 watts SP12C — 250 watts
SPISA — 50 watts SP15A — 500 watts
Half-Space Reference Efficiency
SPEC — 0.9%
SP12C — 1.9%
SP15A — 3.5%
Amplifier Power Requirements,
Continuous Âverage at 8 Ohms, for the
Following Average Sound Pressure
Levels, Mid-Band, in the Reverberant
Field of a Typical Living room (R=200)
with Peaks 10 dB above Average {Long-
Term Average Power Capacity not to be
exceeded)
Medium Level {85 dB SPL)
SP8C — 1,4 watt
SP12C — 0.66 watt
SP15A — 0.36 watt
Loud Level {95 dB SPL)
SPEC — 14.0 watts
SP12C — B.6 watts
SP15A — 3.6 watts
Very Loud Level {105 dB SPL)
SPEC — 140 watts
SP12C — 66 watts
SP15A — 36 watts
Maximum Level
SPBC — 250 watts (107 dB)
CP19C — ?25N wate {111 AR)
Impedance
Nominal Minimum
SPBC — 8 ohms SP8C — 6.7 ohms
SP12C — B ohms SP12C — 6.7 ohms
SP15A —8 ohms SP15A — 6.2 ohms
Thiele-Small Driver Parameters Nominal
{see Special Note an Low-Frequency
Performance section)
Те
Free-Air Resonance Frequency
SPBC — 55 Hz
SP12C — 45 Hz
SP15A — 40 Hz
Ves
Electro-Magnetic Q at fs
SP8C — 0.49
SP12C — 0.75
SP15A — 0.49
MS
Mechancial Q at fs
Рес — 6.
SP12C — 5.9
SPI5BA — 5.0
Total O at fs E
Qes + Oms
SPEC — 0.45
SP12C — 0.67
SP15A — 0.45
Vas
Volume of Air Having Same
Acoustic Compliance as Driver
Suspension
SP8C — 1.0 ft3
SP12C — 5.9 ft3
SP15A — 9.9 ft3
To
Half-Space Reference Efficiency
sP8C — 0.9%
3P12C — 1.9%
SP15A — 3.5%
Vo
Peak Displacement Volume of
Diaphragm {= So Xmax)
SPEC— 3.6 in3
SP12C — 10.8 ft3
SPISA — 25 ind
D
Effective Diaphragm Area
SP8C — 30 in2
SP12C — AA in2
BechoVbice®
a Ces company -
Comp
DO
Amex
Peak Linear Displacement of
Diaphragm
SP8C — 0.12 in
SPIZC— 0,13 in
SP15A — 0.20 in
PE(max)
Thermally Limited Maximum Input
Power
SP8C — 75 watts
SP12C — 25 watts
SP15A — 50 watts
Voice Coil Diameter
5 — 2 п
SP12C — 2 in
SP16A — 2-1/2 in
Magnet Weight
SPBC — 22 oz
SP12C — 22 oz
SP15A — 78 oz
Magnet Material — Ceramic
Dimensions
Overall Diameter
C — 8-3/8 in
SP12C — 12-3/16 in
SP15A — 15-1/8 in
Overall Depth
SPBC — 4-3/4 in
SP12C —B-1/8 in
SP15A — 7 in
Mounting Bolt Circle Diameter
SPBC — 7-5/8 in
SP12C — 11-9/16 in
SP15A — 14-9/16 in
Bolt Hole Diameter
9/32 in. in all units
Mounting Hale Number
SP8C— à
SP12C-—8
SP16A — 8
Baffle Hole Diameter
Front Mounting
SP8C — 7-1/4 in
SP12C — 11-1/16 in
SP16A — 14 in
Rear Mounting
SP8C — 7-1/8 in
SP12C — 10-15/16 in
SP15A — 1411/8 in
Met Weight
SP8C —7 Ib 20z
SP120. — 11 1h 17 m7
ELECTRO-VOICE COMPONENT
SPEAKERS
Electro-Voice component speakers have
traditionally provided the hobbyist and
professional with the flexibility of
custom installation as well as the oppor-
tunity for simple “building-block”
system expansion and improvement. A
comprehensive group of cone speakers,
mid-frequency horns and drivers, horn
tweeters, crossovers, and accessories is
available. Additionally, all Electro-Voice
component speakers offer conversion
efficiencies substantially higher(3 to 8
dB) than typical "bookshelf" home
speaker systems. This high efficiency is
essential for most professional audio
applications. In the home it permits
accurate reproduction of the high sound
levels of live music or, for more normal
listening levels, the use of amazingly
small amplifiers for satisfactory
reproduction.
Electro-Voice cone speakers have now
been thoroughly revised to reflect the
latest knowledge of rational, optimized
low-frequency speaker enclosure design.
The result is a combination of extended
law-distortion bass response, high
efficiency, and modest cabinet size
simply not available in other component
speakers.
THE “SP” SERIESOF
LOUDSPEAKERS
All of the SP series of Electro-Voice
speakers have a rugged die-cast frame
far maximum mechanical stability —
much more so than the ordinary
stamped frame speaker. All three units
utilize a ceramic magnet with adequate
magnetic assembly for maximum flux in
the gap and consequent high efficiency.
All three units incorporate a centrally
mounted free-edge cone for improved
high frequency propagation,
SPEC
The SPBC was designed for full-range
use or as a woofer in a two or three way
system. For an eight inch speaker it will
provide remarkable performance in the
bass range even in a small enclosure—
only 1.2 cubic feet. The SP8C is ideal
for a small or “starter” high-fidelity
component speaker system, It will
produce quite adequate sound pressure
levels in environments such as the
average living room.
SP12C
The SP12C was also designed for full
range use or service only as a woofer,
Due to the greater power handling
capacity as well as the larger magnetic
assembly, as compared to the SP8C, this
unit will produce about 3.5 dB greater
sound pressure than the smaller unit. In
addition, it may be mounted in a larger
box to provide response to half an
octave lower frequency than the SP8C.
SPIBA
This is the largest unit of the SP series.
The 78 ounce magnet is the same as that
used on the EVM 18B high power music
speaker. The voice coil is also the same
and this combination leads to sound
pressure levels about 8 dB above that
produced by the SP8C. The SP15A can
be used for excellent performance as a
very low frequency woofer with
essentially flat output down to about 32
Hz. There are very few musical instru-
ments producing signal in this very low
frequency range. Even with this perfor-
mance the enclosure is not so large as to
be unwelcome in the usual listening
room. The voice coil of edge wound
aluminum wire makes maximum use of
the space within the magnetic gap. In
addition, the light weight aluminum
results in improved performance at
higher frequencies for a speaker this
large.
RECOMMENDED ENCLOSURES
The "SP" series of loudspeakers have
been designed for mounting in vented
boxes appropriate to the speaker charac-
teristics. The use of a vented box with
Its tuned feature complements the per-
formance of the speaker and provides
maximum low-frequency performance
consistent with size and speaker para-
meters. A vented box not only increases
the low-frequency output but also
reduces distortion for a given level.
In the following fist we have attempted
to choose a typical vented box size that
best complements the SP8C, SP12C,
and SP15A. Other vented box sizes and
tunings are quite feasible and may give
performance more suitable for a partic-
ular application. For further infor-
mation please turn to the section of this
sheet entitled: “Special Note on Low-
Frequency Performance”. If additional
information is needed please ask for a
copy of Bulletin 10B.
The low-frequency performance of
these three vented enclosures is
summarized below:
SPBC SP12C SP15A
Ve 1.2ft3 55f9 7.5 НЗ
fe 47 Hz 43Hz Ñ2d0Hz
fa S0HZ 43Hz 240H7
fa 0 36 Hz 32 Hz 30 Hz
TILL 40 Hz 34 Hz 31 Hz
Vg Net internal enclosure volume, not
including volume displaced by
bracing, port, or speaker. Varia-
tions of + 10% are acceptable.
fg Helmholtz resonance frequency of
box-vent combination.
f3 Frequency at which the small signal
(normal listening levels) acoustic
power vs, frequency is down 3 dB
relative to the mid-band output.
fig Frequency at which the small signal
(normal listening levels) acoustic
power vs. frequency is down 10 dB
relative to the mid-band output.
fLL Usable low-frequency limit, the
frequency at which the large-signal
maximum acoustic power output
vs. frequency is 10 dB below the
maximum mid-band output (due to
either thermal or displacement
limitations).
Dimensions for the three recommended
vented enclosures are shown below:
Vg Volume
SP8C — 1.2 НЗ
SP12C — 5.5 ft3
SP15A — 7.5 НЗ
Inside Height (H)
SPEC — 16-5/16 in
SP12C — 27-1/4 in
SP15A — 31-1/8 in
Inside Width (W)
SP8C — 13 in
SP12C — 21-1/2 in
SP15A — 23-7/8 in
Inside Depth (D)
SP8C — 10-5/16 in
SP12C — 17-1/4 in
SPIBA — 19 in
Port Area (XY)
SP8C — 4.3 in?
SP12C — 30.4 in2
SP15A — 33.1 in?
Port Depth (L)
SP8C — 2.6 in
SP12C — 3.4 in
SPISA — 3.2 in
An outline drawing of a typical
enclosure 15 shown below.
JE
| x
ENCLOSURE CONSTRUCTION
Speaker enclosures should be con-
structed of rigid materials such as void-
free plywood or particle board. In
general, 3/4-inch thick material is most
satisfactory, although smaller enclosures
(approximately 2 cubic feet and under)
may be successfully constructed of
5/8-inch material. It is mandatory that
the joints between the pieces of wood
be strong and well sealed. Simple butt
joints secured with wood screws or nails
and white glue are very satisfactory.
Removable panels should be secured
with wood screws and weather stripping
tape. For joints longer than about 3
feet, internal glue blocks may be appro-
priate. In the largest boxes—greater than
about 6 cubic feet—bracing is usually
required for the largest expanses of
wood to prevent sympathetic vibrations
from affecting overall system perfor-
mance. Proper bracing technique splits a
rectangular panel into two equal rectan-
gles with the brace placed along the
panel's longest dimension. Good bracing
materials are 2 X 2 dimension lumber or
4-inch widths of 3/4-inch plywood,
placed on edge. Three mutually adjacent
inside surfaces of the enclosure (top,
one side and rear) should be lined with a
one to two inch thickness of glass wool
or similar acoustic absorptive material
to prevent internal reflections from
affecting mid-frequency performance.
No absorptive material should be placed
over or within the port.
The location of the speaker on the
mounting baffle is relatively unimpor-
tant but close-to-ear-level mounting will
provide best mid- and high-frequency
performance in the listening room, The
enclosure’s height, width, and depth
may be changed as long as (1) the
internal volume remains the same
(+ 10%) and (2) extreme differences
between any two dimensions are
avoided. The required port area can be
obtained by any convenient combi-
nation of width (Y) and height (X) as
long as its long dimension is no more
than five times the short dimension. The
port is normally located on the front
baffle board but may also be on any
other box surface that has free access to
the listening room. For most accurate
box tuning the port should be na closer
than several inches from the nearest
adjacent enclosure wall, The port's
proximity to the speaker is
unimportant.
SPEAKER INSTALLATION AND
HOOKUP
The “SP” series of speakers may be
installed either on the inside or outer
surface of the mounting baffle. As with
all quality speakers, care should be
taken in mounting if best results are to
be obtained. Drill four or more
mounting holes and cut the mounting
baffle opening in accordance with the
dimensions given in the Specifications
section. To mount the speaker four or
more carriage bolts with nuts and
washers may be used. The SPEC will
accomodate four 9/32 inch diameter
bolts while the SPTZA and SP15A will
accomodate eight bolts of the same
dimension. Wood screws are not recom-
mended for mounting the speaker.
Secure the speaker to the baffle board
just tightly enough to compress the
speaker gasket. Excessive tightening is
not necessary since the compressible
gasket will form a satisfactory seal with
only nominal pressure.
To avoid any significant amplifier power
loss in the speaker lines and undesire-
able change in low-frequency response,
wire size must be properly chosen. 18
gauge stranded wire (commonly called
lamp or "zip" cord) is satisfactory for
lengths up to 38 feet limiting the loss in
sound output to an insignificant 0.5 dB.
If longer speaker lines are required use
progressively larger wire sizes: 16 gauge
to 60 feet, 14 gauge to 96 feet and 12
gauge to 150 feet. These lengths assume
an impedance level of one speaker or 8
ohms. Two speakers in parallel have gn
impedance of four ohms so if connected
to the end of a single speaker line the
lengths listed above must be halved. If it
is desired to run the speaker line under a
carpet, TV twin lead may be used for
short distances.
PERFORMANCE IMPROVEMENT
WITH BUILDING BLOCK KITS
While the SP8C, SP12C and SP15A will
provide quite adequate sound repro-
duction under most circumstances an
improvement in performance can easily
be realized by adding a tweeter and
mid-frequency speaker.
The tweeter will provide the most
dramatic improvement and should be
added first through the use of a BB1
High-Frequency Building Block Kit. The
BB1 includes a T35 horn tweeter, X36
Crossover Network, Level Control,
wiring harness and mounting hardware.
In addition to extending the high-
frequency response beyond the limits of
normal audibility the BB1 provides
more precise definition of high-
frequency wave forms and improved
high-frequency dispersion in the
listening area. The improved dispersion
makes it possible for the listener to
move considerably off the central axis
while experiencing very little change in
sound quality.
The BB4A Mid-Frequency Building
Block Kit, consisting of an 1823M
Driver, BHD Diffraction Horn, X8
Crossover Network, and a Level Control!
with wiring harness provides additional
improvement in performance after
installation of the BB1. The BB4A
further reduces the frequency range
which must be reproduced by the cone
speaker, reducing harmonic and inter-
modulation distortion in the total
system. The BB4A's diffraction horn
improves dispersion in the listening area
in addition to increasing efficiency. The
improved mid-frequency performance
provided by the BB4A is especially
important because instrument and voice
harmonics which determine the char-
acter of the sound are found in this
frequency range.
SPECIAL NOTE ON LOW-
FREQUENCY PERFORMANCE
The recommended enclosures and
associated performance specifications
displayed earlier were determined in
accordance with the definitive analysis
of A. N. Thiele, R. H. Small, and others.
The performance of speakers in sealec
enclosures (including acoustic suspen-
sion types) has been well understood for
some time. In contrast, vented systems
have been designed using not much
more than cut-and-try methods with
little real engineering know-how. How-
ever, the above mentioned analysis has
changed this picture completely.
Thiele showed the similarity between a
speaker in an enclosure and an electrical
high-pass filter circuit. Application of
well known filter analysis techniques led
to quite accurate performance calcula-
tions for any speaker mounted in any
vented or sealed cabinet. Moreover, it
was shown that a properly executed
speaker /vented-enclosure combination
held clear-cut advantages over a sealed
system in the areas of efficiency, box
size, low-frequency limit, and distor-
tion. These results make the choices of
box size, low-frequency limit,
efficiency, power-handling capacity, and
maximum acoustic power output
relatively easy to make. In fact, Thiele
even presented in tabular form quite a
number af possible vented box choices
having optimum performance charac-
teristics (see A. N. Thiele, "'Loud-
speakers in Vented Boxes: Part |"
J. Audio Eng. Soc., Vol. 19, May 1971,
p. 388).
© Gulton Industries, Inc. 1983
By appiying the work of Thiele and
Small, Electro-Voice engineers
developed a computer program which
easily, quickly, and accurately predicts
the performance of any speaker-box
system in the frequency range where the
diaphragm is acting as a simple piston.
The upper limit for this operation is
usually the frequency at which the dia-
meter of the diaphragm becomes a large
fraction of 8 wavelength.
The Thiele-Small Driver Parameters
shown in the Specifications section
include the speaker characteristics
required by the computer program to
develop the small and large signal per-
formance of a given speaker and
enclosure combination.
For more information on this subject,
ask for Bulletin 108. It includes
additional vented enclosure recommena-
ations for Electro-Voice component
speakers and a detailed bibliography of
the work of Thiele, Small, and others.
Also, where the Thiele-Small Driver
Parameters are known, Bulletin 10B
shows how to choose the size and
tuning of a vented enclosure and how to
determine the low-frequency response
of vented and sealed speaker systems
using scientific pocket calculators.
WARRANTY (Limited) —
Electro-Voice High Fidelity Speakers
and Accessories are guaranteed for five
years from date of original purchase
against malfunction due to defects in
workmanship and materials. If such
malfunction occurs, unit will be
repaired or replaced (at our option)
without charge for materials or labor if
delivered prepaid to the proper
Electro-Voice service facility. Unit will
be returned prepaid. Warranty does not
cover finish or appearance items or mal-
function due to abuse or operation at
other than specified conditions. Repair
by other than Electro-Voice or its
authorized service agencies will void this
warranty,
For correct shipping address,
instructions on return of Electro-Voice
products for repair, and locations of
authorized service agencies, please
write: Service Department,
Electro-Voice, Inc, 600 Cecil Street,
Buchanan, Michigan 48107 (Phone:
616/695-6831).
Electro-Voice also maintains complete
facilities for non-warranty service of
E-V products.
Specifications subject to change
without notice.
Part Number 53001 — 614
a Gulton cowa»* ELECTRO -VOICE, Inc., 600 CECIL ST., BUCHANAN, MICH. 49107
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement