Technical Data Sheet

Add to My manuals
3 Pages

advertisement

Technical Data Sheet | Manualzz

Technical Data Sheet

TB550 Polyurethane Enamel 2.8 VOC High Gloss

Valspar Automotive

P.O. Box 1461

Minneapolis, MN 55440

1.800.845.2500 www.valsparindustrialmix.com

TB550 / US

Product Information

Product Description:

TB550 Polyurethane Enamel 2.8 VOC High Gloss - 70% Binder and 30% Color Toner. A two-component, Polyurethane Enamel formulated to give outstanding gloss, depth, chemical resistance and durability. Specially developed for Industrial OEM and aftermarket repair industry. Air-dry and force dry capabilities. Also provides excellent UV protection. This product is recommended for use where 2.8 VOC is required.

Substrates: Properly prepared Steel and Aluminum substrates and sprayed with Epoxy Primer: FP420/423 Epoxy Primer/Sealer

(wet on wet or sanded)

Other: Solvent resistant surfaces, cleaned/sanded/hardened original and cured coatings.

Preparation:

Dry Sanding Coating: VIM Primer/existing finishes: P320 – P360

Steel surface Preparation: Abrasive blast to SSPC and NACE recommentation with a uniform blast profile of 0.7 to 2.0mil (20-50µm)

Galvanized: Sweep Blasting recommended

Note: The layer thickness of the Primer should be three (3) times more than the grade of the shot blasted surface.

(More Detailed information go-to Preparation and Pre-treatment at www.valsparindustrialmix.com)

Cleaning: Surface must be dry and free from any contamination, e.g. oil, grease, release agents.

Use only approved cleaning products per your local regulations.

(More Detailed information go-to cleaning processes at www.valsparindustrialmix.com)

Physical Data:

4:1 4:1 +25%

RTS REGULATORY DATA (No Reduction)

LBS/GAL g/L

(Exempt Reducer Line)

LBS/GAL g/L

Actual VOC

Regulatory VOC (less water and exempt solvents)

Density

Total Volatile Content

Water Content

Exempt Compound Content

Physical properties:

Chemical base

Density lbs/gal (kg/l)

Volume solids (%)

Weight Solids (%)

Flash point

Pot life / 77°F (+25°C)

Shelf life

Polyurethane

8.36 lbs/gal (1.0 kg/L)

58%

2.8 Max.

2.8 Max.

8 - 12

WT.%

20 - 50

0

0 - 10

340 Max.

340 Max.

960 - 1440

VOL.%

30 - 55

0

0 - 10

Coverage (sq ft - DFT)

Gloss

Color

2.55 Max.

2.8 Max.

8 - 12

WT.%

20 - 50

0

10 - 30

306 Max.

340 Max.

960 - 1440

VOL.%

30 - 55

0

10 - 25

Approx. 944sq ft / 1.0mil

High gloss 90GU/20°

Binder Transparent

64%

20°F (-7.0°C)

Approx. 2 - 3 hours

Temperature Stability

Processing temperature

Humidity

Min. 24 month under normal storage conditions and unopened tins

Dry Heat up to 284°F/140°C

50 – 104°F (+10°C - 40°C)

Until 80% R.H.

Date of issue: 1/2015 - Version: 3.0 These products are for Professional use only

Page

1

Application Data

Cleaning:

Use only approved products per your local regulations

Technical Data Sheet

TB550 Polyurethane Enamel 2.8 VOC High Gloss

Valspar Automotive

P.O. Box 1461

Minneapolis, MN 55440

1.800.845.2500 www.valsparindustrialmix.com

TB550 / US

Primed or existing finishes – Valspar 155 Surface Cleaner or

170 AquaClean Low VOC WaterBase or

AD680 Water Based Cleaner must be cleaned, dry and free from any contamination, e.g. oil, grease

Preparation: Dry sanding coating: VIM Primer/Existing finishes P320 – P360

Galvanized: Sweep blasting recommended

Abrasive blast: with a uniform blast profile of 0.7 to 2mil (20-50µm)

Before using:

The product must be shaken before adding the Color Toners and thoroughly stirred directly after the Activator and

Reducer have been added.

Mixing ratio with Color Toner:

(By Volume)

TB550 Polyurethane Enamel 2.8 VOC High Gloss

CT Range of VIM Color Toners

(For mixing formula’s see Color Focus)

70 parts

30 parts

Mixing stick:

Use the mixing stick M2 4:1 (74-202=3:1/4:1) or

M6 (74-206 standard) / M7 (74-207 large) Universal cm-stick

Low VOC: If used as instructed, this product is designet to comply with Voatile Organic Compound (VOC) Standards in low-VOC jurisdictions, for Automobile Refinish Coatings. Confirm compliance with state and local air quality rules before use.

US National Rule + Canada: If used as instructed, this product is designed to comply with the US and Canadian

National Volatile Organic Compound (VOC) Emission Standards for Automobile Refinish Coatings. Confirm compliance with state and local air quality rules before use.

Component: Use component as instructed per Valspar guidelines. Verify that intended end use of component is in compliance with state and local air quality rules before use.

Mixing Ratio with Activator: TB550 Polyurethane Enamal 2.8 VOC High Gloss

(by Volume) and with Reducer:

(For USA 2.8 VOC)

AU540 Polyurethane Activator

RE6x0 Exempt Reducer (RE670/680/690)

(Rx670 Fast / 680 Medium / 690 Slow)

Faster process of drying:

Viscosity:

AA600 Accelerator

20 – 26 sec. (DIN4/68°F/20°C)

4 parts

1 part

+0-25%

+3-5%

Gun set up:

Gravity Feed

Siphon Feed

HVLP (Gravity Feed)

Pressure Pot

Airless / and with air support

Atomizing Air Pressure

Airless - metallic application:

Application:

Recommended Film Thickness:

Nozzle / Tip Size:

1.3 – 1.5 mm

1.6 – 1.8 mm

1.3 – 1.5 mm

1.1 – 1.4 mm

0.009” – 0.011”

Air Pressure:

35-40 psi (2.5-2.8 bar)

35-45 psi (2.5-3.1 bar)

30 psi (2.0 bar) Inlet Air

35-40 psi (2.5-2.8 bar)

2500-3000 psi ( until 200 bar)

55-65 psi (1.5-4.5 bar)

Follow the instructions on our TDS: TB550-R

Option 1:

½ coat – followed by 1 full wet coat

1.6 – 2.1mil DFT (25 – 50µm)

Option 2:

2 medium/full wet coats

2.1 – 2.7mil DFT (50 – 80µm)

Date of issue: 1/2015 - Version: 3.0 These products are for Professional use only

Page

2

Technical Data Sheet

TB550 Polyurethane Enamel 2.8 VOC High Gloss

Clean up: RS6x0 Reducer Solvent or

(check the local regulations!) RE6x0 Exempt Reducer

Flash between coats at 77°F/25°C:

Before baking at 77°F/25°C:

Air–dry at 77°F/25°C:

(DFT dependent)

Force–dry at 140 – 158°F:

(60°C – 70°C)

IR-Dry

Option 1:

N/A

10 minutes

Tack Free:

To Tape:

To Recoat:

2 hour

6 hours

16 hours (overnight)

Valspar Automotive

P.O. Box 1461

Minneapolis, MN 55440

1.800.845.2500 www.valsparindustrialmix.com

TB550 / US

Option 2:

10 – 15 minutes or until previous coat is non stringing

10 minutes

30 minutes

140°F/60°C object temperature

12 – 15 minutes

The panel must not reach a temperature above 194°F/90°C.

Use suitable respiratory protection (the use of fresh air supply respirator recommended).

Polish: Dust and minor imperfections can be polished out after the stated air-dry times have been reached, or after a full bake at 60°C object temperature, followed by a cool down of the object to ambient temperature. Before polishing, make sure the surface is well cured.

Follow the instructions of the polish manufacture.

Precautions: During application all health and safety measures referring to the use and handling of coating materials are to be observed, e. g. existing regulations issued by the trade associations in the Chemical Industry. For Health and

Safety information please refer the Material Safety Datasheet (MSDS). Information also available at www.valsparindustrialmix.com

Note: The products listed are intended only for the professional user and for professional use. All recommendations in words and writing given on the use of our products to customers or users are not binding and do not give reasons for secondary obligations resulting from the bill of sale. Every care is taken to ensure that the technical information provided is accurate and up to date according to the present state of knowledge in science and our experience. These recommendations do not, however, exempt the customer from autonomously checking whether our products are suitable for the intend purpose. The durability of the coating system largely depends on the thorough preparation of the surface. Furthermore our universal terms of delivery and payment are applicable.

With the publication of this Technical Data Sheet all previous versions regarding this product are no longer valid.

If used as instructed, this product is designed to comply with the US National Volatile Organic Compound (VOC) Emission Standard for Automobile Refinish Coatings.

Confirm compliance with state and local air quality rules before use. The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN

WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or a refund of its purchase price, at our option.

Date of issue: 1/2015 - Version: 3.0 These products are for Professional use only

Page

3

advertisement

Related manuals

advertisement