eZ430-RF2500 Development Tool User`s Guide
eZ430-RF2500 Development Tool
User's Guide
Literature Number: SLAU227F
September 2007 – Revised June 2015
Contents
Preface ........................................................................................................................................ 4
1
eZ430-RF2500 Overview. Wireless Made Easy. ........................................................................ 5
2
Kit Contents, eZ430-RF2500 .................................................................................................. 6
3
Developing With eZ430-RF2500T Target Board ........................................................................ 7
4
Specifications ...................................................................................................................... 9
5
Supported Devices ............................................................................................................. 10
6
MSP430 Application UART .................................................................................................. 10
7
Software Installation ........................................................................................................... 11
8
9
10
11
12
13
14
15
7.1
Installing the IDE ........................................................................................................ 11
7.2
Installing the Sensor Monitor Visualizer Application ............................................................... 11
Hardware Installation .......................................................................................................... 11
SimpliciTI™ Network Protocol ............................................................................................. 11
Demo – eZ430-RF2500 Sensor Monitor.................................................................................. 12
10.1
Demo Hardware Setup ................................................................................................. 12
10.2
Demo Firmware Download ............................................................................................ 13
10.3
Demo Software GUI Setup ............................................................................................ 14
10.4
Demo Options ........................................................................................................... 14
Suggested Reading ............................................................................................................
Frequently Asked Questions (FAQ) ......................................................................................
eZ430-RF2500 Schematics ...................................................................................................
Detailed Hardware Installation Guide ....................................................................................
IAR Workbench Compatibility Guide .....................................................................................
14
15
16
20
22
Revision History .......................................................................................................................... 23
2
Table of Contents
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
www.ti.com
List of Figures
1
eZ430-RF2500 ............................................................................................................... 5
2
eZ430-RF2500 Battery Board .............................................................................................. 6
3
eZ430-RF2500 Development Tool
4
eZ430-RF2500 USB Debugging Interface 6-Pin Male Header ....................................................... 10
5
9600 bps With No Flow Control .......................................................................................... 10
6
eZ430-RF2500 Sensor Monitor
7
IAR Embedded Workbench KickStart Workspace ..................................................................... 13
8
eZ430-RF, USB Debugging Interface, Schematic ..................................................................... 16
9
eZ430-RF, USB Debugging Interface, Schematic ..................................................................... 17
10
eZ430-RF2500T, Target Board and Battery Board, Schematic ...................................................... 18
11
eZ430-RF, USB Debugger, PCB Components Layout ................................................................ 19
12
eZ430-RF, USB Debugger, PCB Layout ................................................................................ 19
13
eZ430-RF2500T, Target Board, PCB Layout ........................................................................... 19
14
Windows XP Hardware Recognition ..................................................................................... 20
15
Windows XP Hardware Recognition for MSP430 Application UART................................................ 20
16
Windows XP Found New Hardware Wizard ............................................................................ 20
17
Windows XP Hardware Wizard ........................................................................................... 21
18
Windows XP Warning...................................................................................................... 21
19
Device Manager ............................................................................................................ 22
........................................................................................
..........................................................................................
7
12
List of Tables
1
eZ430-RF2500T Target Board Pinouts ................................................................................... 7
2
Battery Board Pinouts ....................................................................................................... 8
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
List of Figures
3
Preface
SLAU227F – September 2007 – Revised June 2015
Read This First
If You Need Assistance
Support for MSP430™ devices and the eZ430-RF2500 is provided by the TI Product Information Center
(PIC). Contact information for the PIC can be found on the TI website at www.ti.com. Additional devicespecific information can be found on the MSP430 website at www.ti.com/msp430 and www.ti.com/ez430rf.
NOTE:
IAR Embedded Workbench® KickStart is supported by Texas Instruments.
Although IAR Embedded Workbench KickStart is a product of IAR, Texas Instruments
provides support for KickStart. Therefore, please do not request support for KickStart from
IAR. Consult all provided documentation with KickStart before requesting assistance.
We Would Like to Hear from You
If you have any comments, feedback, or suggestions, let us know by contacting support@ti.com.
MSP430, Code Composer Studio, SimpliciTI are trademarks of Texas Instruments.
Embedded Workbench is a registered trademark of IAR Systems.
4
Preface
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
User's Guide
SLAU227F – September 2007 – Revised June 2015
eZ430-RF2500 Development Tool
1
eZ430-RF2500 Overview. Wireless Made Easy.
The eZ430-RF2500 is a complete USB-based MSP430 wireless development tool providing all the
hardware and software to evaluate the MSP430F2274 microcontroller and CC2500 2.4-GHz wireless
transceiver.
The eZ430-RF2500 uses the IAR Embedded Workbench Integrated Development Environment (IDE) or
Code Composer Studio™ (CCS) IDE to write, download, and debug an application. The debugger is
unobtrusive, allowing the user to run an application at full speed with both hardware breakpoints and
single stepping available while consuming no extra hardware resources.
The eZ430-RF2500T target board is an out-of-the box wireless system that may be used with the USB
debugging interface, as a stand-alone system with or without external sensors, or may be incorporated
into an existing design.
The USB debugging interface enables the eZ430-RF2500 to remotely send and receive data from a PC
using the MSP430 Application UART.
eZ430-RF2500 features:
• USB debugging and programming interface featuring a driverless installation and application
backchannel
• 21 available development pins
• Highly-integrated ultra-low-power MSP430 MCU with 16-MHz performance
• Two general-purpose digital I/O pins connected to green and red LEDs for visual feedback
• Interruptible push button for user feedback
Figure 1. eZ430-RF2500
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
5
Kit Contents, eZ430-RF2500
www.ti.com
Figure 2. eZ430-RF2500 Battery Board
2
Kit Contents, eZ430-RF2500
•
The hardware includes:
– Two eZ430-RF2500T target boards
– One eZ430-RF USB debugging interface
– One AAA battery pack with expansion board (batteries included)
NOTE: Visit the TI website for the latest versions of the documentation and development software
for eZ430-RF2500:
•
MSP430x2xx Family User’s Guide (SLAU144)
•
eZ430-RF2500 User’s Guide (SLAU227)
•
Code Composer Studio (CCS) Integrated Development Environment (IDE)
•
IAR Embedded Workbench KickStart IDE
•
eZ430-RF2500 Sensor Monitor (Code and Visualizer) (SLAC139)
6
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Developing With eZ430-RF2500T Target Board
www.ti.com
3
Developing With eZ430-RF2500T Target Board
The eZ430-RF2500 can be used as a stand-alone development tool. Additionally, the eZ430-RF2500T
target board also may be detached from the debugging interface and integrated into another design by
removing the plastic enclosure. The target board features an MSP430F2274 and most of its pins are
easily accessible. The pins are shown in Figure 3 and described in Table 1 and Table 2.
Battery Board
More development pins
(0.1-inch spacing)
Power In and Ground
Spy-Bi-Wire Interface
F2274
P3.5/UCA0RXD/UCA0SOMI
CC2500
VCC (3.6 V)
TEST/SBWTCK
eZ430-RF2500T
Target Board
RST/SBWTDIO
GND
UART
P3.4/UCA0TXD/UCA0SIMO
18 available development pins
(0.1-inch spacing)
Figure 3. eZ430-RF2500 Development Tool
Table 1. eZ430-RF2500T Target Board Pinouts
Pin
Function
Description
1
GND
Ground reference
2
VCC
Supply voltage
3
P2.0 / ACLK / A0 / OA0I0
General-purpose digital I/O pin
ACLK output
ADC10, analog input A0
4
P2.1 / TAINCLK / SMCLK / A1 / A0O
General-purpose digital I/O pin
ADC10, analog input A1
Timer_A, clock signal at INCLK
SMCLK signal output
5
P2.2 / TA0 / A2 / OA0I1
General-purpose digital I/O pin
ADC10, analog input A2
Timer_A, capture: CCI0B input/BSL receive, compare: OUT0 output
6
P2.3 / TA1 / A3 / VREF− / VeREF− / OA1I1 /
OA1O
General-purpose digital I/O pin
Timer_A, capture: CCI1B input, compare: OUT1 output
ADC10, analog input A3
Negative reference voltage output/input
7
P2.4 / TA2 / A4 / VREF+ / VeREF+ / OA1I0
General-purpose digital I/O pin
Timer_A, compare: OUT2 output
ADC10, analog input A4
Positive reference voltage output/input
8
P4.3 / TB0 / A12 / OA0O
General-purpose digital I/O pin
ADC10 analog input A12
Timer_B, capture: CCI0B input, compare: OUT0 output
9
P4.4 / TB1 / A13 / OA1O
General-purpose digital I/O pin
ADC10 analog input A13
Timer_B, capture: CCI1B input, compare: OUT1 output
10
P4.5 / TB2 / A14 / OA0I3
General-purpose digital I/O pin
ADC10 analog input A14
Timer_B, compare: OUT2 output
11
P4.6 / TBOUTH / A15 / OA1I3
General-purpose digital I/O pin
ADC10 analog input A15
Timer_B, switch all TB0 to TB3 outputs to high impedance
12
GND
Ground reference
13
P2.6 / XIN (GDO0)
General-purpose digital I/O pin
Input terminal of crystal oscillator
14
P2.7 / XOUT (GDO2)
General-purpose digital I/O pin
Output terminal of crystal oscillator
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
7
Developing With eZ430-RF2500T Target Board
www.ti.com
Table 1. eZ430-RF2500T Target Board Pinouts (continued)
Pin
Function
Description
15
P3.2 / UCB0SOMI / UCB0SCL
General-purpose digital I/O pin
USCI_B0 slave out/master in when in SPI mode
SCL I2C clock in I2C mode
16
P3.3 / UCB0CLK / UCA0STE
General-purpose digital I/O pin
USCI_B0 clock input/output
USCI_A0 slave transmit enable
17
P3.0 / UCB0STE / UCA0CLK / A5
General-purpose digital I/O pin
USCI_B0 slave transmit enable
USCI_A0 clock input/output
ADC10, analog input A5
18
P3.1 / UCB0SIMO / UCB0SDA
General-purpose digital I/O pin
USCI_B0 slave in/master out in SPI mode
SDA I2C data in I2C mode
Table 2. Battery Board Pinouts
Pin
8
Function
Description
1
P3.4 / UCA0TXD / UCA0SIMO
General-purpose digital I/O pin
USCI_A0 transmit data output in UART mode (UART communication from 2274 to PC)
Slave in/master out in SPI mode
2
GND
Ground reference
3
RST / SBWTDIO
Reset or nonmaskable interrupt input
Spy-Bi-Wire test data input/output during programming and test
4
TEST / SBWTCK
Selects test mode for JTAG pins on Port1. The device protection fuse is connected to
TEST. Spy-Bi-Wire test clock input during programming and test
5
VCC (3.6V)
Supply voltage
6
P3.5 / UCA0RXD / UCA0SOMI
General-purpose digital I/O pin
USCI_A0 receive data input in UART mode (UART communication from 2274 to PC)
Slave out/master in when in SPI mode
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Specifications
www.ti.com
4
Specifications
MSP430F2274
• 16-MIPS performance
• 200-ksps 10-bit SAR ADC
• Two built-in operational amplifiers
• Watchdog timer, 16-bit Timer_A3 and Timer_B3
• USCI module supports UART/LIN, (2) SPI, I2C, or IrDA
• Five low-power modes that draw as little as 700 nA in standby
PARAMETER
MIN
TYP
MAX UNIT
OPERATING CONDITIONS
Operating supply voltage
1.8
3.6
V
Operating free-air temperature range
-40
85
°C
CURRENT CONSUMPTION
Active mode at 1 MHz, 2.2 V
270
390
µA
Standby mode
0.7
1.4
µA
Off mode with RAM retention
0.1
0.5
µA
16
MHz
OPERATING FREQUENCY
VCC ≥ 3.3 V
CC2500
• 2.4-GHz radio-frequency (RF) transceiver
• Programmable data rate up to 500 kbps
• Low current consumption
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
OPERATING CONDITIONS
Operating supply voltage
1.8
3.6
V
CURRENT CONSUMPTION
RX input signal at the sensitivity limit, 250 kbps
RX input signal 30 dB above the sensitivity limit, 250 kbps
Optimized current
16.6
Optimized sensitivity
18.8
Optimized current
13.3
Optimized sensitivity
15.7
mA
mA
Current consumption TX (0 dBm)
21.2
mA
Current consumption TX (-12 dBm)
11.1
mA
RF CHARACTERISTICS
Frequency range
2400
2483.5
MHz
Data rate (programmable)
1.2
500
kbps
Output power (programmable)
-30
0
dBm
Optimized current, 2-FSK, 230-kHz
RX filter bandwidth, 1% PER
Sensitivity, 10 kbps
Optimized sensitivity
Sensitivity, 250 kbps
-99
-101
Optimized current, 500-kHz RX
filter bandwidth, 1% PER
-87
Optimized sensitivity
-89
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
dBm
9
Supported Devices
5
www.ti.com
Supported Devices
The eZ430-RF USB debugging interface may be used as a standard Flash Emulation Tool through its
Spy-Bi-Wire interface. The eZ430-RF USB debugging interface supports the following MSP430 families:
• MSP430F20xx
• MSP430F22xx
The connector on the USB debugging interface is backward compatible with the eZ430-F2013 and T2012
target boards.
TX
3.6 V
TEST/SBWTCK
RST/SBWTDIO
Supports eZ430-F2013
and T2012 target boards
GND
RX
Figure 4. eZ430-RF2500 USB Debugging Interface 6-Pin Male Header
6
MSP430 Application UART
The eZ430-RF USB debugging interface features a back channel MSP430 Application UART that may be
used independently of a debug session. This allows the user to transfer serial data to a terminal window at
a fixed rate of 9600 bps with no flow control. See Figure 5 for typical settings.
Figure 5. 9600 bps With No Flow Control
Check the Device Manager for COM port assignment of the MSP430 Application UART. For more details,
see Section 14.
10
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Software Installation
www.ti.com
7
Software Installation
Two different development software tools for the MSP430 are available from TI: IAR Embedded
Workbench KickStart and Code Composer Studio (CCS). The term "KickStart" refers to the limited version
of Embedded Workbench that allows up to 4KB of C-code compilation.
7.1
Installing the IDE
1. Download the IDE of your choice:
IAR Embedded Workbench KickStart: http://www.ti.com/tool/IAR-KICKSTART
Code Composer Studio: http://www.ti.com/tool/ccstudio
2. Respond to the prompts to install the software. The installation procedure installs the IDE and TI files.
7.2
Installing the Sensor Monitor Visualizer Application
1. Download the latest version of eZ430-RF2500 Sensor Monitor (Code and Visualizer):
http://www.ti.com/lit/zip/slac139
2. Run Sensor Monitor Installer.exe.
3. Choose the installation path for the software.
4. Open the eZ430-RF2500 Sensor Monitor using the shortcut that is installed on the desktop.
8
Hardware Installation
1. Insert the eZ430-RF into USB port. The debugging interface automatically installs itself.
2. When prompted for the software for the MSP430 Application UART, allow Windows to Install the
software automatically. This is only possible if either IAR KickStart R4.64 (or higher) or the Sensor
Monitor Visualizer has already been installed. For more information, see Section 14.
9
SimpliciTI™ Network Protocol
The SimpliciTI™ network protocol is a proprietary, low-power radio-frequency (RF) protocol targeting
simple, small RF networks (<100 nodes). The SimpliciTI network protocol is designed for easy
implementation with minimal microcontroller resource requirements. The protocol runs out of the box on
TI’s MSP430 ultra-low-power microcontrollers and multiple RF transceivers.
Small low-power RF networks typically contain battery-operated devices, which require long battery life,
low data rate, and low duty cycle, and have a limited number of nodes talking directly to each other. With
the SimpliciTI network protocol, MCU resource requirements are minimal, resulting in lower system cost
for low-power RF networks. More complex mesh networks that need routing typically require 10× the
program memory and RAM to implement.
Despite the modest resources required, SimpliciTI network protocol supports End Devices in a peer-topeer network topology, the option to use an Access Point to store and forward messages, and Range
Extenders to extend the range of the network up to four hops. Future releases will add more sophisticated
features such as frequency agility, an ETSI-compliant listen-before-talk discipline, and a software security
routine for message encryption.
The SimpliciTI network protocol supports a wide range of low-power applications including alarm and
security (smoke detectors, glass breakage detectors, carbon monoxide sensors, and light sensors),
automated meter reading (gas meters and water meters), home automation (appliances, garage door
openers, and environmental devices), and active RFID.
The SimpliciTI network protocol is provided as source code under a free license without royalties.
Developers are encouraged to adapt the protocol to their own specific application needs. For information
on compatibility, updates, and the latest version of the SimpliciTI protocol, visit www.ti.com/simpliciti.
The eZ430-RF2500 demonstration application uses the SimpliciTI protocol to demonstrate a temperature
sensor network application that provides a starting point to develop a wireless applications.
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
11
Demo – eZ430-RF2500 Sensor Monitor
10
www.ti.com
Demo – eZ430-RF2500 Sensor Monitor
eZ430-RF2500 is preloaded with a wireless temperature sensor network firmware and may be
reprogrammed at any time. This network consists of an Access Point that measures its own temperature
and also wirelessly receives temperature measurements from End Devices. End Devices measure their
temperature once per second and then enter a low-power mode to reduce battery usage. The Access
Point transmits all measured data to the PC through the UART backchannel. The included PC Sensor
Monitor Visualizer provides a demonstration of the eZ430-RF2500 using the SimpliciTI protocol across a
star network. In the PC Sensor Monitor Visualizer, the center node is the Access Point and the attached
bubbles are the End Devices. The PC application displays the temperature of both the End Devices and
Access Point. Additionally, the PC application is capable of simulating distance from its access point when
the End Devices are moved. The number of End Devices can be expanded by adding more target boards
in the star network as seen in Figure 6.
Figure 6. eZ430-RF2500 Sensor Monitor
10.1 Demo Hardware Setup
1. Connect the eZ430-RF2500 to a USB port on the PC.
2. Connect the second eZ430-RF2500T target board to the battery board. Insert the jumper on the board
to power up the device.
12
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Demo – eZ430-RF2500 Sensor Monitor
www.ti.com
10.2 Demo Firmware Download
The following steps describe how to update the demo application firmware on the eZ430-RF2500 target
boards and are not required out of the box.
1. Download the demo software from at http://www.ti.com/lit/zip/slac139 and extract the archive to your
local drive.
2. Open IAR Workbench KickStart.
3. Select Open Existing Workspace, and browse for the demo application workspace (*.eww) file.
4. To download demo firmware, follow step 4a for Access Point firmware and step 4b for End Device
firmware.
(a) Right click on Access Point project in the workspace and click Set as Active as shown in
Figure 7.
(b) Right click on End Device project in the workspace and click Set as Active.
Figure 7. IAR Embedded Workbench KickStart Workspace
5. Select Project → Debug in IAR to download the code for the target boards.
6. Select Debug → Go to start running code while in debug mode.
7. Select Debug → Stop Debugging exits the debug mode while leaving the target board executing
code.
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
13
Demo – eZ430-RF2500 Sensor Monitor
www.ti.com
10.3 Demo Software GUI Setup
1. Download the latest version of the demo software and run Sensor Monitor Installer.exe from the PC
folder. After installation, a shortcut is placed on the desktop.
2. Ensure the Access Point is connected to the PC.
3. Apply power to the End Device.
4. Launch eZ430-RF2500 Sensor Monitor Demo Visualizer. The application should automatically display
End Devices when in range.
10.4 Demo Options
1. Go to Menu → Settings.
2. Under the settings menu, the demo application is capable of displaying values in Celsius or
Fahrenheit.
3. Checking the box Disable Animations disables the dynamic distance change, thus decreasing CPU
processing on PC.
4. See the demo application help file by clicking Help for more detailed options.
11
Suggested Reading
The primary sources of MSP430 information are the device-specific data sheets and user’s guides. The
most current information is found at www.ti.com/msp430. Information specific to the eZ430-RF2500
development tool can be found at www.ti.com/ez430-rf.
MSP430 device user’s guides and the FET user's guide may be accessed from the website. The FET
user's guide includes detailed information on setting up a project for the MSP430 using IAR.
Documents that describe the IAR tools (Workbench/C-SPY, the assembler, the C compiler, the linker, and
the library) are installed with the IDE in common\doc and 430\doc. The documents are in PDF format.
Supplements to the documents (the latest information) are available in HTML format in the same
directories. 430\doc\readme_start.htm provides a convenient starting point for navigating the IAR
documentation.
14
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Frequently Asked Questions (FAQ)
www.ti.com
12
Frequently Asked Questions (FAQ)
1. Does the eZ430-RF2500 support fuse blow?
The eZ430-RF USB debugging interface lacks the JTAG security fuse-blow capability. To ensure
firmware security on devices going to production, the USB Flash Emulation Tool or the Gang
Programmer, which include the fuse-blow feature, are recommended.
2. What is the voltage supplied to the eZ430-RF2500T target board from the debugging interface?
The eZ430-RF USB debugging interface supplies a regulated 3.6 V to the eZ430-RF2500T target
board.
3. Can other programming tools interface to the eZ430-RF2500T target board?
The eZ430-RF2500T target board works with any programming tool supporting the 2-wire Spy-Bi-Wire
interface. Both the MSP430 USB FET (MSP-FET430UIF) and the Gang Programmer (MSP-GANG430)
support these devices. See MSP-FET430 Flash Emulation Tool User’s Guide (SLAU138) for details on
using MSP430 USB FET and the Gang Programmer for a 2-wire Spy-Bi-Wire interface.
4. What versions of IAR Embedded Workbench and Code Composer Studio are supported?
The eZ430-RF2500 hardware is supported by IAR Embedded Workbench KickStart Release 4.64 (IAR
3.42F) and Code Composer Studio v4 or higher.
5. What are the part numbers for the connectors between the eZ430-RF USB debugger and the
eZ430-RF2500T target board?
Header: Mill-Max 850-10-006-20-001000
Socket: Mill-Max 851-93-006-20-001000
6. Where can I obtain more information about the 2.4-GHz chip antenna?
Part Number: 7488910245
Wϋrth Electronik Group: www.we-online.com
7. I am not able to select the MSP430 Application UART, cannot receive data, or the demo app
doesn’t appear to change.
Ensure that the Application UART driver is correctly installed. Install either the Sensor Monitor
Visualizer or IAR KickStart 3.42F or higher and follow the directions in Section 14.
To determine if the driver is correctly installed:
(a) Plug in the eZ430-RF USB debugging interface.
(b) Right click My Computer and select Properties.
(c) Select the Hardware tab and click on Device Manager.
(d) Under Ports (COM & LPT) should be an entry for "MSP430 Application UART (COM xx)".
If the entry is there, but no characters are received, restart the PC.
If the Application UART is not listed, install the driver by following the instructions in Section 14.
8. When trying to compiler the Sensor Monitor Demo project in IAR, I receive the following error:
Error[e117]: Incompatible runtime models. Module ISR specifies that '__rt_version' must be '3', but
module LHAL_GDOxHandlers has the value '2'
Use the latest version of the demo software and use IAR KickStart v4.x or later.
Early versions of the demo code included a precompiled version of the SimpliciTI library for IAR 3.x.
IAR 4.x changes the calling conventions, which returns Error[e117] when trying to build libraries for an
older version of the compiler.
9. What kind of range should I expect to get with the eZ430-RF2500?
Based on practical rage testing with one node connected to a PC and the other node connected to the
battery board, we have measured indoor line-of-sight range of more than 50 meters. This range can be
significantly affected by the orientation of the boards and the environment. Note that the eZ430RF2500 target board was designed to optimize for factor and does not focus on maximizing RF range.
Visit the TI website for additional reference designs and antenna options.
10. Why is my battery board different than in the documentation?
Since introduction, the eZ430RF-2500 battery board was slightly modified. The connections and
function remain the same.
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
15
eZ430-RF2500 Schematics
13
www.ti.com
eZ430-RF2500 Schematics
Figure 8. eZ430-RF, USB Debugging Interface, Schematic
16
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Schematics
www.ti.com
Figure 9. eZ430-RF, USB Debugging Interface, Schematic
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
17
eZ430-RF2500 Schematics
www.ti.com
Figure 10. eZ430-RF2500T, Target Board and Battery Board, Schematic
18
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Schematics
www.ti.com
Figure 11. eZ430-RF, USB Debugger, PCB Components Layout
Figure 12. eZ430-RF, USB Debugger, PCB Layout
Figure 13. eZ430-RF2500T, Target Board, PCB Layout
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
19
Detailed Hardware Installation Guide
14
www.ti.com
Detailed Hardware Installation Guide
1. Download the demo software from at http://www.ti.com/lit/zip/slac139 and extract the archive to the
local drive.
2. Install the eZ430-RF2500 Sensor Monitor Demo Visualizer from the PC folder in the demo software
zip. This installs the necessary drivers on your system.
3. Insert the eZ430-RF2500 into a USB port of the PC.
4. Windows should recognize the new hardware as Texas Instruments MSP-FET430UIF (see
Figure 14). Windows should automatically install the drivers for the MSP-FET430UIF as a HID tool.
Figure 14. Windows XP Hardware Recognition
5. Windows recognizes another new hardware driver to be installed called MSP430 Application UART
(see Figure 15).
Figure 15. Windows XP Hardware Recognition for MSP430 Application UART
NOTE: This Installation Step is Optional. The USB debugging interface works without the MSP430
Application UART as long as (R4.64 or newer) IAR Workbench is used.
6. The Found New Hardware Wizard opens a dialog window. Select No, not this time and click Next (see
Figure 16).
Figure 16. Windows XP Found New Hardware Wizard
20
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Detailed Hardware Installation Guide
www.ti.com
7. Select Install the software automatically (Recommended) (see Figure 17), if IAR KickStart R4.64 or
higher has already been installed.
Figure 17. Windows XP Hardware Wizard
8. The Wizard should find the appropriate driver for a Windows XP system; it shows a warning that
Microsoft did not certify the driver. The drivers have been tested exhaustively, and this warning may be
ignored. Click Continue Anyway (see Figure 18).
Figure 18. Windows XP Warning
9. The Wizard continues to install the driver and then provides notification when it has finished the
installation of the software.
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
eZ430-RF2500 Development Tool
21
IAR Workbench Compatibility Guide
www.ti.com
10. The eZ430-RF2500 is now installed and ready to use. The assigned COM port for the MSP430
Application UART is shown in the Windows Device Manager (see Figure 19).
Figure 19. Device Manager
15
IAR Workbench Compatibility Guide
NOTE: In this document, "IAR version" refers to the IAR compiler version. This can be obtained by
clicking Help → About → Product Info.
IAR KickStart version 3.42F (FET_R4.64)
• Minimum version compatible with eZ430-RF USB debugging interface board
• Compatible with eZ430-RF2500 Sensor Monitor demo v1.00
IAR KickStart version 4.09A+ (FET_R5.10+)
• Compatible with eZ430-RF USB debugging interface board
• Compatible with SimpliciTI libraries 1.0.3+
• Compatible with eZ430-RF2500 Sensor Monitor demo v1.02+
22
eZ430-RF2500 Development Tool
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Revision History
www.ti.com
Revision History
Changes from April 2, 2009 to June 15, 2015 .................................................................................................................. Page
•
•
•
•
•
•
Removed CD from kit contents (no longer included) and updated links to related documentation and software ............ 6
Removed references to install CD, and changed all references and links for CCE to CCS ................................... 11
Changed description in Section 10.2, Demo Firmware Download, for software download instead of install from CD ..... 13
Changed description in Section 10.3, Demo Software GUI Setup, for software download instead of install from CD ..... 14
Changed description in Section 11, Suggested Reading, to refer to the TI website for additional information ............. 14
Changed step 1 in Section 14, Detailed Hardware Installation Guide, to download software instead of load from CD ... 20
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLAU227F – September 2007 – Revised June 2015
Submit Documentation Feedback
Copyright © 2007–2015, Texas Instruments Incorporated
Revision History
23
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising