null  null
TCB501HQ
CDMOS Linear Integrated Circuit Silicon Monolithic
TCB501HQ
Maximum Power 49 W BTL × 4ch Audio Power Amp IC
1.
Description
The TCB501HQ is a power IC with built-in four-channel BTL
amplifier developed for car audio application. The maximum
output power POUT is 49 W using a pure complementary P-ch
and N-ch DMOS output stage.
In addition, a standby switch, a mute function, output offset
voltage detector, high-side switch and various protection features
are included.
Weight: 7.7g (typ.)
2.
Applications
Power Amp IC developed for car audio applications.
3.
Features
• High output power, low distortion, and low noise property (for details, refer to the Table 1 Typical
Characteristics).
• Built-in high-side switches. (Pin 25)
• Built-in output offset detection for full time
(Pin 1)
• Built-in muting function. (Pin 22)
• Built-in auto muting functions (for low VDD and standby
sequence)
Table 1 Typical characteristics
(Note 1)
Test condition
• Built-in standby switch. (Pin4)
• Built-in various protection circuits (thermal shut down,
over-voltage, short to GND, short to VDD, and output to output
short)
• Start stop Cruising corresponded to VDD=6V (Engine idle
reduction capability)
Typ.
Unit
Output power (POUT)
VDD = 15.2 V, max power
49
VDD = 14.4 V, max power
44
VDD = 14.4V,
THD = 10%
29
THD =10%
W
24
Total harmonic distortion (THD)
POUT = 4 W
0.006
%
Output noise voltage (VNO) (Rg = 0 Ω)
Filter: A weighted
45
µV
Operating Supply voltage range (VDD)
RL_amp = 4 Ω
6 to 18
RL_amp = 2 Ω
6 to 16
V
Note 1:
Typical test conditions: Unless otherwise specified, VDD = 13.2 V, f = 1 kHz, RL_amp = 4 Ω, and Ta = 25°C
Rg: Signal source resistance
©2016 TOSHIBA Corporation
1
2016-06-28
TCB501HQ
11
C1: 0.22 μF
6
20
VDD2
VDD1
9
IN1
8
7
AC-GND
C1: 0.22 μF
IN2
12
5
2
13 Pre-GND
3
AC-GND
C1: 0.22 μF IN3
15
C6: 1 μF
17
18
16 AC-GND
19
AC-GND
C1: 0.22 μF IN4
14
21
24
5V
Play
Mute
4 Stby
R1: 47 kΩ
22 Mute
23
AC-GND
H-SW
Offset Det
C3: 0.1 μF
10
Ripple
C5:
3900 μF
C2: 10 μF
Block Digaram
C4: 1 μF
4.
+B
OUT1 (+)
PW-GND1
RL_amp
OUT1 (−)
OUT2 (+)
PW-GND2
RL_amp
OUT2 (−)
OUT3 (+)
PW-GND3
RL_amp
OUT3 (−)
OUT4 (+)
PW-GND4
RL_amp
OUT4 (−)
25
1
Some of the functional blocks, circuits or constants labels in the block diagram may have been omitted or simplified
for clarity.
In the following explanation, a "channel" is a circuit which consists of INx, OUTx (+), OUTx (-),
and PW-GNDx. (x: 1 to 4)
2
2016-06-28
TCB501HQ
5.
5.1
Pin Configuration
Pin configuration (top view)
H-SW
PW-GND4
OUT4 (-)
MUTE
OUT4 (+)
VDD1
OUT3 (-)
PW-GND3
OUT3 (+)
AC-GND
IN3
IN4
Pre-GND
IN2
IN1
Ripple
OUT1 (+)
PW-GND
OUT1 (-)
VDD2
OUT2 (+)
Stby
OUT2 (-)
PW-GND2
OffsetDet
3
2016-06-28
TCB501HQ
5.2
Pin Description
Pin
Symbol
I/O
Description
1
Offset Det
Vod-OUT
Output offset/short voltage detector output
2
PW-GND2
―
Ground for OUT2
3
OUT2(-)
OUT
OUT2(-) output
4
Stby
VST-IN
Stand-by voltage input
5
OUT2(+)
OUT
OUT2(+) output
6
VDD2
VDD-IN
Supply voltage 2
7
OUT1(-)
OUT
OUT1(-) output
8
PW-GND1
―
Ground for OUT1
9
OUT1(+)
OUT
OUT1(+) output
10
Ripple
―
Ripple voltage
11
IN1
IN
OUT1 input
12
IN2
IN
OUT2 input
13
Pre-GND
―
Signal ground
14
IN4
IN
OUT4 input
15
IN3
IN
OUT3 input
16
AC-GND
―
Common reference voltage for all input
17
OUT3(+)
OUT
OUT3(+) output
18
PW-GND3
―
Ground for OUT3
19
OUT3(-)
OUT
OUT3(-) output
20
VDD1
VDD-IN
Supply voltage 1
21
OUT4(+)
OUT
OUT4(+) output
22
Mute
VmuteIN
Mute voltage input
23
OUT4(-)
OUT
OUT4(-) output
24
PW-GND4
―
Ground for OUT4
25
H-SW
HSW
High-side switch output
4
2016-06-28
TCB501HQ
11
C1: 0.22 μF
6
20
VDD2
VDD1
9
IN1
8
7
AC-GND
C1: 0.22 μF
IN2
12
5
2
13 Pre-GND
3
AC-GND
C1: 0.22 μF IN3
15
C6: 1 μF
17
18
16 AC-GND
19
AC-GND
C1: 0.22 μF
14
IN4
21
24
5V
Mute
Component
Recommended
Name
Value
C1
4 Stby
R1: 47 kΩ
C4: 1 μF
Play
22 Mute
23
AC-GND
Pin
Purpose
0.22 μF
INx(x:1 to 4)
C2
10 μF
C3
H-SW
25
Offset Det
1
C3: 0.1 μF
10
Ripple
C5:
3900 μF
Specification of External Parts
C2: 10 μF
6.
+B
OUT1 (+)
PW-GND1
RL_amp
OUT1 (−)
OUT2 (+)
PW-GND2
RL_amp
OUT2 (−)
OUT3 (+)
PW-GND3
RL_amp
OUT3 (−)
OUT4 (+)
PW-GND4
RL_amp
OUT4 (−)
Effect (Note1)
Lower than Recommended Value
Higher than Recommended Value
To eliminate DC
Cut-off frequency becomes higher
Cut-off frequency becomes lower
Ripple
To reduce ripple
Turn on/off time shorter
Turn on/off time longer
0.1 μF
VDD1, VDD2
To provide sufficient
oscillation margin
Reduces noise and provides sufficient oscillation margin
C6
1 μF
AC-GND
Common reference
voltage for all input
Pop noise is suppressed when C1: C6 = 1:4. (Note2)
C5
3900 μF
VDD1, VDD2
Ripple filter
Filter for power supply humming and ripple
R1
47kΩ
C4
1μF
Mute
Mute ON/OFF
Pop noise becomes larger
Smooth switching
Switching time becomes longer
Note1: When the unrecommended value is used, please examine it enough by system evaluation.
Note2: Since “AC-GND” pin is a common reference voltage for all input, this product needs to set the ratio of an input
capacitance (C1) and the AC-GND capacitance (C6) to 1:4
Note3: Use the low leak current capacitor for C1 and C6.
5
2016-06-28
TCB501HQ
7.
Standby switch function (Pin 4)
The power supply can be turned on or off via pin 4
(Stby). The threshold voltage of pin 4 is below table.
The power supply current is about 0.01 μA (typ.) in the
standby state.
Power
ON
Power
VSB (V)
ON
OFF
0 to 0.8
OFF
ON
2.2 to VDD
10kΩ
OFF
Table 2 Standby Control Voltage (VSB): Pin 4
Stand-by
4
Figure
Internal circuit for standby
図 1 1スタンバイ回路図
Benefits of the Standby Switch
(1)
(2)
VDD can be directly turned on or off by a
microcontroller, eliminating the need for a switching relay.
Since the control current is minuscule, a low-current-rated switching relay can be used.
Relay
High-current-rated switch
Battery
Battery
VDD
VDD
From micro controller
–Conventional method –
Low-current-rated switch
Stby
From micro controller
Battery
VDD
Stby
Battery
VDD
– Using the standby switch-
Figure 2 Standby switch
6
2016-06-28
TCB501HQ
8.
Mute Function (Pin 22)
The audio mute function is enabled by setting pin 22 Low. R1 and C4 determine the time constant of the mute
function. The time constant affects pop noise generated when power or the mute function is turned on or off; thus, it
must be determined on a per-application basis. (Refer to Figures 3 and 4.)
The values of external elements (R1, C4) of this pin have decided them based on 5V control. In case that it is
controlled by other than 5V, please reexamine the value of the external pull-up resistor as follows;
For example:
When the control voltage is changed from 5V to 3.3V, the pull-up resistor should be: 3.3V/5V×47 kΩ=31kΩ
ATT – VMUTE
10 kΩ
C4
Mute attenuation
R1
22
ATT (dB)
5V
Control voltage: VMUTE
(V)
Figure 4 Mute attenuation − VMUTE (V)
Figure 3 Mute Function
7
2016-06-28
TCB501HQ
9.
Auto Muting Functions
The TCB501HQ has two automatic mute functions.
a) Low VDD Mute (Automatic mute function)
b) Standby Off Mute.
9.1
Low VDD Mute
When the supply voltage became lower than 5.5V (typ.), The TCB501HQ operates the mute circuit
automatically. This function prevents the large audible transient noise which is generated by low VDD.
9.2
Standby-Off Mute
The TCB501HQ operates the mute circuit during the standby-off transition. When the ripple voltage
reached VDD/5, the standby-off mute is terminated. Additionally, in the standby-off transition, it is
recommended that the external mute has to be ON till the internal mute-OFF, and that the timing of the
external mute-OFF has to be set after the internal mute-OFF.
VSB
Stby pin
(Pin 4)
t
0
VM
Mute control
voltage
t
0
VM
Mute pin
( Pin 22)
t
0
VDD/4
VDD/5
Ripple pin
(Pin 10)
t
0
Out sound time 500ms (max) Note1
ピ
VDD/2
Output pin
t
0
Note1: Out sound time is changed due to capacity of the C2 capacitor.
8
2016-06-28
TCB501HQ
9.3
Mute-off after standby-off
The pop noise is generated when the capacitor of ripple, input, and ACGND has not finished to charge fully.
Please set “Mute-off” that it is sufficient margin in considering an enough charge time after the middle
point potential stable.
VSB
Stby pin
(Pin 4)
t
0
VM
Mute control
voltage
t
0
VM
Mute pin
( Pin 22)
t
0
VDD/4
Ripple pin
(Pin 10)
t
0
VDD/2
Output pin
t
0
Figure 5 Mute-off transition after standby-off
9
2016-06-28
TCB501HQ
10. High-side Switch
The Q1 (high-side switch) is always turned on during Power-ON.
The high-side switch can be used for many application circuits related to Power-ON. This output incorporates the
backflow prevention structure.
VDD
Q1
25
Rsw
Figure 6 High-side switch
10
2016-06-28
TCB501HQ
11. Output DC Offset Detection
This function detects the offset voltage between OUT (+) and OUT (-). The detection result is gotten by pin1. When
the offset voltage appeared by the external parts accident, for example the leak of coupling capacitor, this function
can contribute to a part of safety system to prevent the speaker damage.
The example flowchart: The safety system to prevent damaging to speakers by abnormal offset.
(a) Offset
detection
(b) Judgment
Normal / Abnormal
(c) To reduce the speaker stress
Standby-ON, Mute-ON etc.
The result of detection does not judge the abnormal offset or not. This function detects only the offset voltage which
is decided by specification.
11.1
Operation description of output offset pin
The result of output offset voltage detection of Pin1 is gotten by the internal open-drain transistor which
synchronizes with offset voltage. This function is always available. If this pin does not be used, connect to
GND or open.
Power Amp IC
Leak or short
Vref
1
Vin(dc)
RS2
E. vol
Vout(dc) > Vin(dc)
V1
+
RS1
Vout(dc)
Vref
−
Vos-det(on)
(Reference)
The specification defines the Offset voltage as
"OUT(+) - OUT(-)"
Rs1 generates the positive offset voltage.
Rs2 generates the negative offset voltage.
Leak or short
Figure 7 Generating example of abnormal output offset voltage
Abnormal offset voltage
+Vos-det(on)
t
Output waveform 0
OUT(+) to OUT(-)
-Vos-det(on)
V1
Outputing low when the
voltage exceeds the
threshold value.
Offset
detection
output
0
Term of abnormal offset vlotage
Figure 8 Output waveform of amplifier and pin 1
11
2016-06-28
TCB501HQ
12. Low voltage operation
The TCB501HQ applies the amplifier circuit to reduce the audible pop noise and sound cutting due to low VDD
voltage.
12.1
Operation description
When the headroom voltage is suppressed by the low VDD, the TCB501HQ switches output middle point
potential from VDD/2 to VDD/4 and reduces the audible pop noise and the sound cutting. The behavior of
outputs (Vout) and ripple (Vrip) is showed the figure 9 below.
(A) VDD > Vth1 Normal operation
(B) VDD < Vth1 Switch middle point potential from VDD/2 to Vrip to keep the headroom voltage.
(C) VDD < Vth2 The C2 (ripple) is discharged with muting, and amplifier is off.
Each of threshold voltage is below.
Vrip = 3V (Ripple pin voltage)
Vhr1 = 2.2V (typ.), Vhr2 = 1.7V (typ.)
Vth1 = Vout+Vhr1 = 2Vrip + Vhr1, Vth2 = Vrip + Vhr2
Figure 9 Output VDD/2 voltage in lowering VDD
12
2016-06-28
TCB501HQ
13. Protection Functions
This product has internal protection circuits such as thermal shut down, over-voltage, short to VDD, short
to GND, and out to out short circuit protections.
(1)
Thermal shut down
It operates when junction temperature exceeds 150°C (typ.).
When it operates, it is protected in the following order.
1.
2.
3.
An Attenuation of an output starts first and the amount of attenuation also increases according
to a temperature rising,
All outputs become in a mute state, when temperature continues rising in spite of output
attenuation.
Shutdown function starts, when a temperature rise continues though all outputs are in a mute
state.
In any case if temperature falls, it will return to normal operation automatically.
(2)
Over-voltage
It operates when voltage exceeding operating range is supplied to VDD pin. If voltage falls, it will
return to normal operation automatically. When it operates, all outputs bias and high-side switch are
turned off and all outputs are shut-off. Threshold voltage is 21.5 V(typ.)
(3)
Short to VDD, Short to GND, Output to output short
It operates when each output pin is in irregular connection and the load line goes over the SOA (Safe
Operation Area) of power transistor (DMOS). When it operates, all outputs bias circuits are turned off
and all outputs are shut-off. If irregular connection is canceled, it will return to normal operation
automatically.
13
2016-06-28
TCB501HQ
14. Absolute Maximum Ratings
(Ta = 25°C unless otherwise specified)
Characteristics
Symbol
Rating
Unit
VDD (surge)
50
V
Max 0.2 s.
Supply voltage (DC)
VDD (DC)
25
V
Max voltage applied for 1 min.
Output current of amplifier (surge )
Io(Peak)
9
A
Power dissipation
PD
125
W
Note 4
Junction temperature
Tj
150
°C
Note 5
Operating temperature range
Topr
-40 to 85
°C
Storage temperature
Tstg
-55 to 150
°C
dV1-2
±0.3
Pre-GND to PW-GND
dV_Gnd
±0.3
VDD
VDD1,2
Stby
Mute
Supply voltage (surge)
VDD1 to VDD2
Voltage
difference
between pins
Voltage of
input pin
Condition
V
Permissive voltage difference
between VDD1 and VDD2
V
Permissive voltage difference
between Pre-GND and
PW-GND
6 to 18
V
RL=4Ω
Stby
GND-0.3 to
VDD+0.3
V
Mute
GND-0.3 to
VDD+0.3
V
In1,2,3,4
GND-0.3 to
VDD+0.3
V
ACG
GND-0.3 to
VDD+0.3
V
Ripple
Rip
GND-0.3 to
VDD+0.3
V
Diag
Diag
GND-0.3 to
VDD+0.3
V
IN
ACGND
The absolute maximum ratings of a semiconductor device are a set of specified parameter values, which must not be
exceeded during operation, even for an instant.
If any of these rating would be exceeded during operation, the device electrical characteristics may be irreparably altered
and the reliability and lifetime of the device can no longer be guaranteed. Moreover, these operations with exceeded
ratings may cause break down, damage, and/or degradation to any other equipment. Applications using the device should
be designed such that each maximum rating will never be exceeded in any operating conditions.
Before using, creating, and/or producing designs, refer to and comply with the precautions and conditions set forth in this
document.
Note 4: Package thermal resistance Rth(j-t) = 1°C/W (typ.) (Ta = 25°C, with infinite heat sink)
Note 5: When the TAB temperature is more than absolute maximum ratings, the thermal shut down system (mute)
operates. The threshold TAB temperature is 160°C(typ.). The threshold TAB temperature is defined as the
highest temperature point of the metal side surface. Regarding heat radiation design, please design the device
so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and
condition.
14
2016-06-28
TCB501HQ
15. Power dissipation
PD (max) – Ta
Power Dissipation PD (max)
(W)
120
(1) Infinite heat sink
Rth(j-t) = 1°C/W
100
(2) Heat sink (Rth(HS) = 3.5°C/W)
Rth(j-t) + Rth(HS) = 4.5°C/W
(3) No heat sink
80
Rth(j-a) = 39°C/W
(1)
60
40
20
(2)
(3)
0
0
25
50
75
Ambient Temperature
100
Ta
125
150
(°C)
16. Operating Range
Characteristics
Supply voltage
Symbol
VDD
Condition
Min
Typ.
Max
Unit
RL=4Ω
6
―
18
V
RL=2Ω
6
―
16
V
15
2016-06-28
TCB501HQ
17. Electrical Characteristics
17.1
Amplifier
(Unless otherwise specified, VDD=13.2V, f=1kHz, , RL_amp=4Ω, RL_sw=39Ω, Vsb/Vm=5V, Ta=25°C)
( ): The guaranteed value by design
Characteristics
Quiescent supply current
Symbol
IQ
Test Condition
VIN = 0V
Min
Typ.
Max
Unit
100
180
320
mA
POUT MAX (1)
VDD = 15.2 V, max POWER
-
49
-
POUT MAX (2)
VDD = 14.4 V, max POWER
-
44
-
POUT (1)
VDD = 14.4 V, THD = 10%
27
29
-
POUT (2)
THD = 10%
21
24
-
VDD = 14.4 V, max POWER
-
80
-
POUT (3)
VDD = 14.4 V, THD = 10%
-
46
-
POUT (4)
THD = 10%
-
45
-
THD
POUT = 5 W
-
0.006
0.07
%
GV
VOUT = 0.775 Vrms
25
26
27
dB
Channel-to-channel voltage gain
△GV
VOUT = 0.775 Vrms
−1.0
0
1.0
dB
Output noise voltage
VNO
Rg = 0 Ω, DIN Audio
-
45
80
μV
Ripple rejection ratio
R.R.
frip = 100 Hz, Rg = 620 Ω
Vrip = 0.775 Vrms
50
70
-
dB
Crosstalk
C.T.
Rg = 620 Ω
POUT = 4 W
-
80
-
dB
Output power
POUT MAX (3)
Output power(RL=2Ω)
Total harmonic distortion
Voltage gain
W
W
VOFFSET
-
−70
0
70
mV
Input resistance
RIN
-
-
100
-
kΩ
Standby current
ISB
Standby state, V4=0, V22=0
-
0.01
1
μA
VSB H
POWER: ON
2.2
VSB L
POWER: OFF
0
-
0.8
VM H
MUTE: OFF
2.2
-
VDD
VM L
MUTE: ON, R1 = 47 kΩ
0
-
0.8
MUTE: ON, DIN Audio
VOUT = 7.75 Vrms → Mute: OFF
85
100
-
Output offset voltage
Standby control voltage
Mute control voltage
Mute attenuation
ATT M
16
VDD
V
V
dB
2016-06-28
TCB501HQ
17.2
High-side switch
(Unless otherwise specified, VDD=13.2V, f=1kHz, RL_amp=4Ω, RL_sw=39Ω, Vsb/Vm=5V, Ta=25°C)
(
Characteristics
): The guaranteed value by design
Test condition
Symbol
Min
Typ.
Max
Unit
400
600
800
mA
Over Current limits
Iprot
Vo = 12.6V
I/O voltage diffirence
dVo
Vsb=5V
―
0.45
(0.8)
V
Delay time (ON)
Tdon
Vo_sw ≥VDD×0.95
―
0.01
(1)
ms
Delay time (OFF)
Tdoff
Switch off voltage
Vo_sw(L)
Peak protection current
Lower limit of output
Ihsw
VHSWL
Vo_sw ≤VDD×0.05
―
0.2
(1)
ms
Vsb=0V, RL_sw=10kΩ
0
0.01
0.1
V
VDD=0V, (HSW=VDD-Δvo)
―
―
200
μA
VDD=4.5V, IOUT=0 to 100mA
3
―
―
V
S
RL = 39Ω
Figure 10 High-side switch measurement circuit
17
2016-06-28
TCB501HQ
17.3
Output offset voltage detection
(Unless otherwise specified, VDD=13.2V, f=1kHz, RL_amp=4Ω, Rpull-up=10kΩ, Vsb/Vref=5V, and Ta=25°C)
( ): The guaranteed value by design
Test condition
Characteristics
Symbol
Supply voltage for detection of output
offset
VDD_offset1
Detection voltage for output offset
Vos1-det(on) Vsb=5V, Vo(+)-Vo(-)
Saturated voltage in detection
P1-sat
Detection time for output offset
Dtime
Vsb=5V, Vref=5V
Rpull-up=10kΩ, Vref=5.0V
In detection (Pin: Low )
Quiescent
18
Min
Typ.
Max
Unit
6
―
18
V
±1.5
±2.0
V
―
100
500
mV
―
300
500
ms
±1.0
2016-06-28
TCB501HQ
11
C1: 0.22 μF
6
20
VDD2
VDD1
9
IN1
8
7
AC-GND
C1: 0.22 μF
IN2
12
5
2
13 Pre-GND
3
AC-GND
C1: 0.22 μF IN3
15
C6: 1 μF
17
18
16 AC-GND
19
AC-GND
C1: 0.22 μF IN4
14
21
24
5V
Mute
4 Stby
R1: 47 kΩ
C4: 1 μF
Play
22 Mute
23
AC-GND
19
H-SW
25
Offset Det
1
C3: 0.1 μF
10
Ripple
C5:
3900 μF
C2: 10 μF
18. Test circuit
+B
OUT1 (+)
PW-GND1
RL_amp: 4Ω
OUT1 (−)
OUT2 (+)
PW-GND2
RL_amp: 4Ω
OUT2 (−)
OUT3 (+)
PW-GND3
RL_amp: 4Ω
OUT3 (−)
OUT4 (+)
PW-GND4
RL_amp: 4Ω
OUT4 (−)
2016-06-28
TCB501HQ
19. Characteristic Chart
19.1 Total Harmonic Distortion vs. Output Power
THD – POUT (ch1)
THD – POUT (ch2)
Vdd = 13.2 V
GV = 26dB
GV = 26dB
RL = 4 Ω
Filter
RL = 4 Ω
Filter
1 kHz
~ 30 kHz
(%)
100 Hz :
: 400 Hz ~ 30 kHz
THD
10 kHz : 400 Hz ~
20 kHz : 400 Hz ~
100 Hz :
1 kHz
~ 30 kHz
: 400 Hz ~ 30 kHz
10 kHz : 400 Hz ~
20 kHz : 400 Hz ~
20 kHz
25°C/W
Total harmonic distortion
20 kHz
25°C/W
Total harmonic distortion
THD
(%)
Vdd = 13.2 V
10 kHz
1500
100 Hz
10 kHz
1500
100 Hz
f = 1 kHz
Output power
POUT
f = 1 kHz
(W)
Output power
RL = 4 Ω
Filter
1 kHz
~ 30 kHz
: 400 Hz ~ 30 kHz
10 kHz : 400 Hz ~
20 kHz : 400 Hz ~
100 Hz :
10 kHz : 400 Hz ~
1 kHz
~ 30 kHz
: 400 Hz ~ 30 kHz
20 kHz : 400 Hz ~
20 kHz
25°C/W
Total harmonic distortion
20 kHz
25°C/W
(%)
GV = 26dB
RL = 4 Ω
Filter
THD
Vdd = 13.2 V
GV = 26dB
100 Hz :
(W)
THD – POUT (ch4)
Vdd = 13.2 V
Total harmonic distortion
THD
(%)
THD – POUT (ch3)
POUT
10 k
25°C/
W
10 kHz
1500
100 Hz
100 Hz
1500
f = 1 kHz
Output power
POUT
f = 1 kHz
(W)
Output power
POUT
(W)
Fig. 11-1 Total Harmonic Distortion of Each Frequency (RL=4Ω)
20
2016-06-28
TCB501HQ
THD – POUT (ch1)
THD – POUT (ch2)
GV = 26dB
RL = 4 Ω
f = 1 kHz
Filter
GV = 26dB
RL = 4 Ω
f = 1 kHz
Filter
400 Hz ~ 30 kHz
(%)
THD
1
6V
0.1
1500
13.2 V
Total harmonic distortion
THD
Total harmonic distortion
400 Hz ~ 30 kHz
10
(%)
10
18 V
0.01
0.001
1
6V
0.1
1500
13.2 V
18 V
0.01
0.001
0.1
1
10
Output power
100
POUT
0.1
(W)
POUT
100
(W)
THD – POUT (ch4)
GV = 26dB
RL = 4 Ω
f = 1 kHz
Filter
400 Hz ~ 30 kHz
10
GV = 26dB
RL = 4 Ω
f = 1 kHz
Filter
400 Hz ~ 30 kHz
(%)
(%)
THD
1
6V
Total harmonic distortion
THD
Total harmonic distortion
10
Output power
THD – POUT (ch3)
10
1
1500
0.1
13.2 V
18 V
0.01
0.001
1
0.1
6V
1500
13.2 V
18 V
0.01
0.001
0.1
1
Output power
10
POUT
100
0.1
1
Output power
(W)
10
POUT
100
(W)
Fig.11-2 Total Harmonic Distortion by Power-supply Voltage (RL=4Ω)
21
2016-06-28
TCB501HQ
19.2 Various Frequency Characteristics
THD – f(ch2)
6V
1500
18 V
VCC = 13.2 V
RL = 4 Ω
POUT = 5 W
13.2 V
No Filter
Total harmonic distortion
Total harmonic distortion
THD
THD
(%)
(%)
THD – f(ch1)
6V
1500
VCC = 13.2 V
RL = 4 Ω
POUT = 5 W
13.2 V
18 V
No Filter
18 V
frequency f
(kHz)
frequency f
13.2 V
6V
1500
VCC = 13.2 V
RL = 4 Ω
POUT = 5 W
18 V
Total harmonic distortion
THD
(%)
THD
Total harmonic distortion
THD – f(ch4)
(%)
THD – f(ch3)
(kHz)
13.2 V
6V
1500
RL = 4 Ω
POUT = 5 W
18 V
No Filter
frequency f
VCC = 13.2 V
No Filter
(kHz)
frequency f
(kHz)
Fig.11-3 Frequency Characteristics of Total Harmonic Distortion
22
2016-06-28
TCB501HQ
GV – f
ATTMUTE
1ch to 4ch
VCC = 13.2 V
RL = 4 Ω
VOUT = 7.75 Vrms (20dBm)
Mute attenuation
VCC = 13.2 V
RL = 4 Ω
VOUT = 0.775 Vrms
1ch to 4ch
(0dBm)
frequency
周 波 数f (kHz)
f (kHz)
frequency f
(kHz)
Fig. 11-4 Frequency Characteristics of Voltage Gain and Mute Attenuation
R.R. – f
R.R.
(dB)
VCC = 13.2 V
RL = 4 Ω
RG = 620 Ω
Vrip = 0.775 Vrms (0dBm)
GV = 26dB
Ripple rejection ratio
Voltage gain
GV
(dB)
(dB)
ATTMUTE – f
1ch
3ch
2ch
4ch
frequency f
(kHz)
Fig. 11-5 Frequency Characteristics of Ripple Rejection Rate
23
2016-06-28
TCB501HQ
C.T. – f (ch2)
Cross talk
4ch
3ch
1ch
Cross talk
2ch
VCC = 13.2 V
RL = 4 Ω
f = 1 kHz
VOUT = 0.775 Vrms (0dBm)
RG = 620 Ω
C.T.
(dB)
VCC = 13.2 V
RL = 4 Ω
f = 1 kHz
VOUT = 0.775 Vrms (0dBm)
RG = 620 Ω
C.T.
(dB)
C.T. – f (ch1)
4ch
3ch
frequency f
(kHz)
frequency f
C.T. – f (ch3)
C.T. – f (ch4)
VCC = 13.2 V
RL = 4 Ω
f = 1 kHz
VOUT = 0.775 Vrms (0dBm)
RG = 620 Ω
C.T.
1ch
2ch
3ch
Cross talk
Cross talk
4ch
C.T.
(dB)
VCC = 13.2 V
RL = 4 Ω
f = 1 kHz
VOUT = 0.775 Vrms (0dBm)
RG = 620 Ω
(dB)
(kHz)
2ch
1ch
frequency f
(kHz)
frequency f
(kHz)
Fig. 11-6 Frequency Characteristics of Cross Talk
24
2016-06-28
TCB501HQ
19.3 Output Power Characteristics to Input Voltage
POUT (ch2) – VIN
10 kHz
100 Hz
Output power
f = 20 kHz
VCC = 13.2 V
RL = 4 Ω
No Filter
Input signal voltage
VIN (rms)
10 kHz
1 kHz
POUT
POUT
1 kHz
VCC = 13.2 V
RL = 4 Ω
No Filter
(V)
Input signal voltage
VIN (rms)
(V)
(W)
POUT (ch4) – VIN
100 Hz
f = 20 kHz
VCC = 13.2 V
RL = 4 Ω
No Filter
VIN (rms)
10 kHz
1 kHz
POUT
1 kHz
100 Hz
f = 20 kHz
Output power
10 kHz
Output power
POUT
(W)
POUT (ch3) – VIN
Input signal voltage
100 Hz
f = 20 kHz
Output power
(W)
(W)
POUT (ch1) – VIN
VCC = 13.2 V
RL = 4 Ω
No Filter
Input signal voltage
(V)
VIN (rms)
(V)
19.4 Power Dissipation vs. Output Power
(W)
PD – POUT (RL = 4 Ω)
Power dissipation
PD
18 V
13.2 V
f = 1 kHz
RL = 4 Ω
6V
4ch drive
Output power
POUT/CH
25
(W)
2016-06-28
TCB501HQ
19.5 Other characteristics
ICCQ – VCC
VCC = 13.2 V
VIN = 0 V
(mA)
RL = 4 Ω
f = 1 kHz
Filter
ICCQ
~ 20 kHz
RL = 
Quicent current
Output noise voltage
VNO
(μV)
VNO – Rg
1ch to 4ch
Signal source resistance
Supply voltage
Rg (Ω)
26
VCC
(V)
2016-06-28
TCB501HQ
20. Package Dimensions
HZIP25-P-1.00F
Unit: mm
Weight: 7.7 g (typ.)
27
2016-06-28
TCB501HQ
21. Attention in Use
• Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of
over current and/or IC failure. The IC will fully break down when used under conditions that exceed its
absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs
from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or
ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings,
such as fuse capacity, fusing time and insertion circuit location, are required.
• If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the
design to prevent device malfunction or breakdown caused by the current resulting from the inrush current
at power ON or the negative current resulting from the back electromotive force at power OFF. For details
on how to connect a protection circuit such as a current limiting resistor or back electromotive force
adsorption diode, refer to individual IC datasheets or the IC databook. IC breakdown may cause injury,
smoke or ignition.
• Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the
protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or
ignition.
• Carefully select external components (such as inputs and negative feedback capacitors) and load
components (such as speakers), for example, power amp and regulator. If there is a large amount of
leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If
this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure
can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In
particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output
DC voltage to a speaker directly.
• Over current Protection Circuit
Over current protection circuits (referred to as current limiter circuits) do not necessarily protect ICs under
all circumstances. If the Over current protection circuits operate against the over current, clear the over
current status immediately. Depending on the method of use and usage conditions, such as exceeding
absolute maximum ratings can cause the over current protection circuit to not operate properly or IC
breakdown before operation. In addition, depending on the method of use and usage conditions, if over
current continues to flow for a long time after operation, the IC may generate heat resulting in breakdown.
• Thermal Shutdown Circuit
Thermal shutdown circuits do not necessarily protect ICs under all circumstances. If the Thermal
shutdown circuits operate against the over temperature, clear the heat generation status immediately.
Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings
can cause the thermal shutdown circuit to not operate properly or IC breakdown before operation.
• Heat Radiation Design
When using an IC with large current flow such as power amp, regulator or driver, please design the device
so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and
condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can
lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design
the device taking into considerate the effect of IC heat radiation with peripheral components.
• Installation to Heat Sink
Please install the power IC to the heat sink not to apply excessive mechanical stress to the IC. Excessive
mechanical stress can lead to package cracks, resulting in a reduction in reliability or breakdown of
internal IC chip. In addition, depending on the IC, the use of silicon rubber may be prohibited. Check
whether the use of silicon rubber is prohibited for the IC you intend to use, or not. For details of power IC
heat radiation design and heat sink installation, refer to individual technical datasheets or IC databooks.
28
2016-06-28
TCB501HQ
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product,
or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all
relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for
Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for
the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product
design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or
applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams,
programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for
such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS,
INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF
DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF
PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology
products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export
laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export
Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in
compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
29
2016-06-28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement