Switching Power Module SPEC (369357)

Switching Power Module SPEC (369357)
Lutron
Switching Power Module
Power Modules
369357f 1 05.16.17
Switching Power Module
Description
•Provides capability for a zone on a GRAFIK Eye control
unit (or other product) to switch a fully loaded circuit of
lighting.
•May be used to switch incandescent, electronic lowvoltage, magnetic low-voltage, HID, fluorescent ballasts,
and neon / cold cathode lighting sources.
•Utilizes Softswitch arcless switching technology.
•Provides power and switching for one zone.
•Up to 3 power modules may be wired on a single
GRAFIK Eye zone.
•Model available for 120 V~ control power.
•Model available for 120 –277 V~ load power.
Works with 120 V~ versions of:
•Lutron 3-wire fluorescent dimmers and RadioRA 2
dimmers (consult Lutron for Vierti products); see
approved list in the dimmers & switches specification
guide at www.lutron.com
•GRAFIK Eye QS control units
•GRAFIK Eye 3000 Series control units
•LP, LCP, and GP dimming panels
•HomeWorks and HomeWorks QS remote power panels
Models and Capacities
Model Number
Control Power
PHPM-SW-DV-WH
120 V~
®
Job Name:
Job Number:
Load Power
120 – 277 V~
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Capacity
16 A
Page
1
Lutron
Switching Power Module
Power Modules
369357f 2 05.16.17
Specifications
Regulatory Approvals
• UL® listed
• CSA certified
• NOM certified
• Complies with requirements for use in other spaces
used for environmental air (plenums) per NEC® 2017 300.22(C)(3)
Power
Terminals
•Accepts up to two 12 AWG (2.5 mm2) wires.
Environment
•32 to 104 °F (0 to 40 °C). Relative humidity less than
90% non-condensing.
•Indoor use only.
•Maximum heat output of module: 15 BTU/hour.
Mounting
•Control voltage: 120 V~
•Load voltage: 120 – 277 V~
•Capacity: Full 16 A
120 –277 V~: 1920 – 4432 W
•Frequency: 50 / 60 Hz, phase-to-neutral.
•Load (output) power: Phase independent of control
device / control voltage.
•Surface- or recess-mount.
Sources / Load Types
•Switches the following load types:
– Incandescent (tungsten)
– Halogen
– LED
– CFL
– Magnetic low-voltage transformer (iron core)
– Electronic (solid-state) low-voltage transformer
– Magnetic and electronic fluorescent dimming ballasts
– Neon/cold-cathode
– HID
•Motors:
– 11⁄2 HP at 277 V~
– 1/2 HP at 120 V~
•May be used with GFI / AFCI breaker protected loads.
Key Design Features
•Patented Softswitch technology.
•Two LEDs on front of unit provide diagnostic information (visible when faceplate is removed).
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
2
Lutron
Switching Power Module
Power Modules
369357f 3 05.16.17
Dimensions
All dimensions shown as: in (mm)
1.2 (30.5)
1.0 (25)
5.1
(129.5)
6.3
(160)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
3
Lutron
Switching Power Module
Power Modules
369357f 4 05.16.17
Mounting
•Mount in 2-gang U.S. wallbox 3.5 in (89 mm) deep or 4 in x 4 in (102 mm x 102 mm) junction box 2.1 in (53 mm) deep.
•Indoor use only.
•This device generates heat; mount only where ambient
temperature is 32 °F to 104 °F (0 °C to 40 °C).
•Mount with arrows facing up to ensure adequate
cooling.
Mount to 2-gang U.S. wallbox
•Allow 4.5 in (114 mm) above and below unit and
between faceplates when mounting several in a
vertical layout.
•Mount so line (mains) voltage wiring is at least 6 ft
(1.8 m) from sound or electronic equipment and
wiring.
•Mount within 7° of true vertical.
Mount to 4 in x 4 in (102 mm x 102 mm),
2.1 in (53 mm) deep U.S. junction box
Mount to 4 in x 4 in (102 mm x 102 mm), 2.1 in (53 mm) deep
U.S. junction box with barrier
(for 277 V~ model if required by local electrical code)
Barrier
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
4
Lutron
Switching Power Module
Power Modules
369357f 5 05.16.17
Wiring
•Pull 12 AWG (2.5 mm2) copper (Cu) wires [167 °F (75 °C) minimum] for input power and load circuit.
•Strip 1/2 in (12 mm) insulation from wires before connecting.
•Run separate neutral for load circuit - no common neutrals.
•May be used with GFI breaker protected loads. Load circuit wiring (from GFI breaker to power
module to load) must be run in its own non-metallic conduit, or nuisance tripping may occur.
Maximum 100 ft (30.5 m) between power module and load.
•May be used with AFCI breaker protected loads. An AFCI circuit can be loaded to the full allowable
NECR rating for switched lighting. If combining dimmed and switched lighting on the same AFCI
circuit, the amount of dimmed lighting should not exceed 1000 W, as this may trip the AFCI breaker.
Single Power Feed
Note: The power module may be on the same circuit as the control unit only if the total load does not exceed
the rating of the breaker.
Circuit breaker
GRAFIK Eye QS
1 2 3 4 5 6 L N
L/H
N
120 V~
Wire to appropriate
zone
Load (Switched)
120 V~
L/H
N
SH
Zone in
Control Neutral
Legend
L /H
N
SH
Line / Hot
Neutral
Switched Hot
Ground
Not Used
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
5
Lutron
Switching Power Module
Power Modules
369357f 6 05.16.17
Wiring
Multiple Power Feeds
The load breaker may be on a different phase than the control breaker.
GRAFIK Eye QS
1 2 3 4 5 6 L N
N
120 V~
L/H
Wire to appropriate
zone
Control breaker
Load breaker
L/H
N
Load wiring
Load (Switched)
L/H
N
SH
Zone in
Control Neutral
Legend
L / H
N
SH
Line / Hot
Neutral
Switched Hot
Ground
Not Used
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
6
Lutron
Switching Power Module
Power Modules
369357f 7 05.16.17
Wiring Multiple Power Modules to a Single GRAFIK Eye Zone
Shown with separate feeds for control and loads. All breakers must be turned off prior to installing or servicing
the modules. Up to 3 power modules may be wired to a single zone.
GRAFIK Eye QS
1 2 3 4 5 6 L N
Wire to appropriate zone
N
L/H
120 V~
Control breaker
Load breaker
L/H
N
Load wiring1
for Power
Module #1
L/H
N
Load
(Switched)
SH
Zone in
Control Neutral
Load breaker
L/H
N
Load wiring1
for Power
Module #2
L/H
N
Load
(Switched)
SH
Zone in
Control Neutral
Load breaker
L/H
N
L/H
N
Load wiring1
for Power
Module #3
1
Load
(Switched)
SH
Zone in
Control Neutral
Load feed: 120 – 277 V~ for PHPM-SW-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
7
Lutron
Switching Power Module
Power Modules
369357f 8 05.16.17
Multi-location Wiring
Note: The power module may be on the same circuit/control zone as the control device only if the total load
does not exceed the rating of the breaker (120 V~ only).
Circuit breaker
L/H
N
Load wiring
(see Note
below)
Load (Switched)
L/H
N
SH
DH
(yellow
or orange
wire)
Zone in
Control Neutral
3-wire
fluorescent
dimmer
120 V~
(main
dimmer)
SH
(red wire)
3-wire
Cap off
fluorescent
dimmer
120 V~
(accessory/
companion
dimmer or 3-way switch)
H/L
N
120 V~
Legend
L/H
N
SH
DH
Line / Hot
Neutral
Switched Hot
Dimmed Hot
Ground
Not Used
®
Job Name:
Job Number:
For specific wire colors, see the wallbox lighting controls
catalog at www.lutron.com/wallbox catalog
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
8
Lutron
Switching Power Module
Power Modules
369357f 9 05.16.17
Wiring a Power Module to an LP, LCP, GP, or HomeWorks Panel
Up to three 3-wire fluorescent power modules may be wired to an output of a 120 V~ LP or LCP panel. The
load type for the output must be set as Eco-10 or Hi-lume fluorescent load type on the panel’s circuit selector
(for an LP or GP panel), controller (for an LCP panel), or HomeWorks software (for a HomeWorks panel).
Wire to appropriate output
Load
wiring1
L/H
N
Load
(Switched)
L/H
N
SH
Zone In
Control
Neutral
(1) 14 to 10 AWG (2.0 to 4.0 mm2) Dimmed
Hot
(1) 14 to 10 AWG (2.0 to 4.0 mm2) Neutral
DH
DH
DH
DH
H
N
N
N
N
N
Load feed:
120 – 277 V~ if used with PHPM-SW-DV-WH power module
1
120 V~ Branch Circuit
Breakers
)Lutron, Lutron, GRAFIK Eye, Softswitch, Vierti,
HomeWorks, Eco-10, and Hi-lume are trademarks of
Lutron Electronics Co., Inc. registered in the U.S. and
other countries.
RadioRA 2 is a trademark of Lutron Electronics Co., Inc.
NEC is a registered trademark of National Fire Protection
Association, Quincy, Massachusetts.
®
Job Name:
Job Number:
Neutral Lug
Power (Line / Hot)
(3) 14 to 2/0 AWG (2.0 to 70 mm2)
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Neutral (1) 14 to 2/0 AWG (2.0 to 70 mm2)
Page
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement