View - Volvo
Volvo Trucks. Driving Progress
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
3553
,492
Cab 2490
Chassis Dimensions [mm]
WB Wheelbase
A
D
N
N
Overall Chassis Length
Center of rear axle to front of body
Rear Overhang (Min.)
Rear Overhang (Max.)
T
Y
Y
W
W
Theoretical Wheelbase
Center of Gravity for Payload (Min.)
Center of Gravity for Payload (Max.)
Body Length (Min.)
Body Length (Max.)
4600
4900
5100
5600
10015 10465 10815 11565
3571 3871 4071 4571
1225 1225 1225 1225
2525 2675 2825 3075
4288
643
643
5856
5856
4588
745
745
6252
6252
4788
813
813
6516
6516
5288
984
984
7175
7175
Chassis Weights [kg]
Front Axles
Rear Bogie
Kerb Weight
Payload (including body, driver, fuel, etc.)
7875 7825 7800 7740
3430 3530 3605 3740
11305 11355 11405 11480
32695 32645 32595 32520
Turning Diameter [mm]
Turning Circle Diameter Kerb to Kerb
Turning Circle Diameter Wall to Wall
18200 19200 19800 21300
19700 20600 21200 22800
Plated Weights [kg]
Design
Gross Vehicle Weight
Gross Combination Weight
Front Axles
Rear Bogie
44000
44000
18000
26000
Important Notes
Chassis Dimensions
Cab Height: +167 mm for CAB-HSLP, +167 mm for CAB-SLP.
Front Axle to Back of Cab: +506 mm for CAB-HSLP and CAB-SLP.
D-measure includes a front clearance of 50 mm and for rigid trucks also a
subframe of 100 mm.
Height can vary ± 20 mm for leaf and ± 10 mm for air suspension.
All dimensions are for unladen chassis and any tag axles down.
Rear overhang used for vehicle weight calculation is the maximum rear
overhang (N Max.) for selected wheelbase.
Weight and dimensions are based upon the following tyres:
Front Axle Tyres:
315/80R22.5
Drive Axle Tyres:
315/80R22.5
Chassis weight includes oil, water, AdBlue, 70 litres fuel and without
driver. Kerb weight can vary ± 3%.
Turning diameters are theoretically calculated.
Legal weights can differ from country to country.
For more detailed weight information, including optional equipment weights,
ask your Volvo sales contact to enter your specification into the Volvo Weight
Information system (WIS).
Do NOT use this drawing for bodybuilding. Refer to Volvo Bodybuilder
Instructions and chassis assembly drawing FM86FR3CTX.
1 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
Transport operation
■ RC-ROUGH
□ RC-VROUG
□ TIPP-PRE
■ UNIFORM
Rough road conditions.
• Less than 95% of the driven distance on well maintained or
less maintained surfaced roads.
and / or
• In total not more than 5% of the driven distance on:
- Very badly maintained surfaced roads.
- Hard packed sand or gravel surface of very bad quality.
- Washboards.
- Soft unpaved surface.
- Off-road.
Trucks built for very rough road conditions are optimised
for:
• More than 5% of the driven distance on:
- Very badly maintained surfaced roads.
- Hard packed sand or gravel surface of very bad
quality.
- Soft unpaved surface.
- Off road.
• Occasional driving in severe off-road conditions.
Tipper vehicle preparation
Basic platform vehicle
■ CHH-XXHI
Chassis height extra high - approx. 1150 mm above ground
level
■ RADD-TR1
Rear leaf suspension, 2 axles - 2 driven (T-ride 75 mm wide
leafs)
Rear leaf suspension, 2 axles - 2 driven (T-ride 90 mm wide
leafs)
■ FMX-DAY
□ FMX-HSLP
□ FMX-SLP
FMX Day cab
FMX Globetrotter sleeper cab
FMX Sleeper cab
■ EU6SCR
Euro 6 emission level with Selective Catalytic Reduction
(SCR), particulate filter and Exhaust Gas Recirculation (EGR)
■ D13K420
□ D13K460
□ D13K500
□ D13K540
□ EBR-EPG
□ EBR-EPGC
□ EBR-VEB+
■ AT2612F
□ ATO2612F
□ PT2606
■ RTH2610F
□ RTH3210F
□ RTH3312
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 420 hp, 2100 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 460 hp, 2300 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 500 hp, 2500 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 540 hp, 2600 Nm
□ MEDIA
□ MEDIADF
□ MEDIANAV
□ MEDIANDF
□ ENOPT
□ ENOPT+
Energy optimization package
Energy optimization+ package
□ OFFRFMXD
□ OFFRFMXS
Construction package for FMX day cab
Construction package for FMX sleeper cabs
Chassis
Core components
□ RADD-TR2
□ AUDHIG
EGR (Diesel Particulate
EGR (Diesel Particulate
■ FST-PAR3
3 leaf front parabolic suspension (stiffer than normal)
□ FAL16.0
■ FAL18.0
□ FAL20.0
Front axle load 16.0 tonnes, double front axles
Front axle load 18.0 tonnes, double front axles
Front axle load 20.0 tonnes, double front axles
■ FSTAB
Front stabilizer with normal stiffness
■ RAL26
□ RAL32
Rear axles load 26 tonnes
Rear axles load 32 tonnes
■ RSTAB1
Rear stabilizer with normal stiffness
□ RSAP2
Heavy duty rear suspension application (with reinforcements)
■ PSS-DUAL
□ PSS-SING
Dual power steering system
Single power steering system
■ PSP-VAR
Power steering pump with variable displacement
□ EBS-MED
EBS (Electronic Brake System) medium package:
- ABS (Anti-lock Braking System)
- Lining Wear Sensing (20 % left)
- Lining Wear Control (incl. wear on the axle)
- Brake Blending
- Drag Torque Control
- Diff Lock Synchronization
- Diff lock Control
- Brake Temperature Warning
- External Brake Demand
- Diagnosis Via Truck Electronic System
- Traction Control System
- Emergency Brake Assistance
- Constant Wheel Brake Monitoring
- Coupling Force Control
- Automatic Parking Brake Activation
- Lining Wear Analyses (calc of remaining mileage)
- Hill Starting Assistance
- EBS status monitoring via Truck Electronic System
EBS (Electronic Brake System) standard package:
- ABS (Anti-lock Braking System)
- Lining Wear Sensing (20 % left)
- Lining Wear Control (incl. wear on the axle)
- Brake Blending
- Drag Torque Control
- Diff Lock Synchronization
- Diff lock Control
- Brake Temperature Warning
- External Brake Demand
- Diagnosis Via Truck Electronic System
- Traction Control System
- Emergency Brake Assistance
- Constant Wheel Brake Monitoring
- Coupling Force Control
- Automatic Parking Brake Activation
EGR (Diesel Particulate
EGR (Diesel Particulate
Engine brake with exhaust pressure governor, EPG
Volvo engine compression brake with exhaust pressure
governor, EPG (for I-shift)
Volvo Engine Brake, VEB+ (high efficiency compression brake
with exhaust pressure governor, EPG)
I-Shift automated mechanical 12-speed gearbox without clutch
pedal, max. engine torque 2600 Nm, max. permitted GCW
100000 kg.
I-Shift automated mechanical 12-speed overdrive gearbox
without clutch, max. engine torque 2600 Nm, max. permitted
GCW 100000 kg.
Suitable for hub reduction rear axles.
Powertronic automatic 6-speed gearbox, max. engine torque
2600 Nm, max. permitted GCW 130000 kg
□ EBS-STD
Rear hub reduction tandem axles - bogie load 26 tonnes, GCW
100 tonnes
Rear hub reduction tandem axles - bogie load 32 tonnes, GCW
100 tonnes
Rear hub reduction tandem axles - bogie load 33 tonnes, GCW
120 tonnes
Packages
□ DRIVEFM
□ DRIVEFM+
Driving package FM
Driving plus package FM
□ BEDFM
Bed resting package FM
■ AUDBAS
Audio basic. RDS radio with CD player, FM/AM antenna and
■ Standard Equipment
speakers in dashboard & doors.
Prepared for Dynafleet office internet portal support.
High power audio system. RDS radio with CD player (also
playing mp3/wma/wav files from CD), FM/AM antenna,
speakers in dashboard & doors & sleeping compartment,
integrated bluetooth phone and USB/Line inputs.
Prepared for Dynafleet office internet portal support.
Media package with infotainment. Prepared for Dynafleet office
internet portal support.
Media package with infotainment. Prepared for both Dynafleet
vehicle onboard support and for Dynafleet office internet portal
support.
Media package with infotainment and Navigation support and
prepared for Dynafleet office internet portal support.
Media package with infotainment and Navigation support and
prepared for Dynafleet vehicle onboard support and for
Dynafleet office internet portal support.
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
2 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
□ TB-L80
Left toolbox 800 mm length (mounting length 800 mm, real
length 730 mm)
Rear conventional multi-leaf suspension
Rear parabolic leaf suspension with normal stiffness
□ TB-R80
Right toolbox 800 mm length (mounting length 800 mm, real
length 730 mm)
□ FBREG-E
Front axle regulating brake valve for EBS
□ CHAIN-S
Snow chains
■ FRAME300
Frame rail section external height 300 mm
□ HOOK-SC
■ FST8080
Frame section thickness - web 8.0 mm / flange 8.0 mm
□
□
□
□
■
Snow chain hooks.
Rear mounted for tractors and side mounted in rear overhang
for rigids. Two hooks on each side.
Frame inner liner from end of engine end to end of bogie
Frame inner liner from end of engine end to end of frame
Frame inner liner from front of bogie to end of bogie
Frame inner liner from front of bogie to end of frame
Frame inner liner from transmission cross member to end of
bogie
Frame inner liner from transmission cross member to end of
frame
■ TOWF-HD1
One heavy duty front towing device
□ AUXPARK
Two extra parking brake chambers
□ RST-MUL
■ RST-PAR1
FIL-EEEB
FIL-EEEF
FIL-FBEB
FIL-FBEF
FIL-TXEB
□ FIL-TXEF
■ BBOX-L
Battery box on left hand side
□ 2BAT210B
■ 2BATT170
□ 2BATT225
Gel batteries 2x210 Ah
Batteries 2x170 Ah
Batteries 2x225 Ah
■ BATTAMP
□ BATTIND
Battery voltage and ampere gauge
Battery voltage, ampere and battery status gauge with visual
alerts
■ MSWI-C
Chassis main switch - battery box placed toggle switch citcuit
shut down
Remote controlled main switch - key fob operated circuit shut
down
□ MSWI-R
■ R315A56
■ UL-FUEL
■ ADTP-L
Right 315 litre aluminium 560 mm high D-shaped diesel tank.
Usable volume is 97% of stated volume.
Min volume 255l
Max volume 630l
Without left diesel tank
□ ADTP-LF
AdBlue tank on left hand side (for dual front axles between the
axles)
AdBlue tank on left hand side at the front
■ ADB032
AdBlue tank usable volume 32 litres
■ FCAP-L
Lockable diesel and AdBlue tank caps
■ FUFF-AS
□ FUFF-ATS
Fuel filling anti-spillage device
Fuel filling anti-theft and anti-spillage devices
□
□
■
□
Horizontal muffler, rear exhaust outlet
Horizontal muffler, vertical exhaust outlet on right hand side
Horizontal and vertical muffler, vertical exhaust
Vertical muffler, vertical exhaust outlet on right hand side
ESH-REAR
ESH-VERT
ESHVVERT
ESV-VERT
□ EXST-SSP
■ EXST-ST
Bright polished vertical stainless steel exhaust top pipe
Aluminized steel vertical exhaust top pipe
□ TOWMBRH High mounted towing member, in centre of frame
□ TOWMBRL1 Towing member, low mounted under the frame (position 1)
□ TOWMBRM Towing member, medium mounted in line with frame lower
flange
■ RFEC-S
□ RFEC-U
Rear frame end, straight cut (for regular platform applications)
Rear frame end, upper cut (for e.g. tipper, refuse and hooklift
applications)
□
□
□
□
□
□
□
Towing coupling Ringfeder RF4040A G-150
Towing coupling Ringfeder RF4045A G-150
Towing coupling Ringfeder RF5055A G-150
Towing coupling Rockinger 400 G-150
Towing coupling Rockinger 50 mm
Towing coupling VBG 750V
Towing coupling VBG 8500
C-RI4040
C-RI4045
C-RI5055
C-RO400G
C-RO50
C-VBG750
C-VBG850
□ TOWR-ONE
One rear towing device in frame end cross member
■ TREL-PK
□ TREL15
□ TREL7-7
Trailer electrical preparation kit (chassis/cab wiring)
15 pol electrical trailer connector (ADR certified)
2x7 pol (24N+24S) electrical trailer connectors (UADR)
□ TBC-DUO
□ TBC-EC
Trailer brake connection, Duomatic
Trailer brake connection, European Community
□ TRBR-STA
Stationary trailer brake control
□ RUP-FOSL
Foldable and slidable aluminium rear underrun protection, EC
approved
□ FFEND-T
Transport mounted fenders on second front axle
□ RFEND-B
□ RFEND-T
Rear 3 piece fenders with anti-spray function (all rear axles)
Transport mounted one-piece rear fenders
□ RFH-BAS
Optimal fender installation (rear and 2nd front axle) with regard
to legal demands, wheel/tyre sizes, chassis height and fifth
wheel height.
Highest fender installation (rear and 2nd front axle).
Suitable for rough and very rough road conditions.
Lower fender installation (rear and 2nd front axle).
Suitable only for smooth road conditions.
Increased risk of fender top wear.
□ RFH-HIG
□ RFH-LOW
■ ATANK-ST
Steel air tanks
LED tail lamps (tail light, exterior marker light, brake light,
hazard warning light, reverse light, rear fog light and reflector).
■ WHC-FIX2
□ WHC-FOL2
Two fixed wheel chocks
2 foldable wheel chocks
□ TL-LED
□ WHCP-F
Wheel chock(s) in the front part of the vehicle.
- TRACTOR, BBOX-L, Fold, 1/2 w chocks
= Top of
left side battery box
- TRACTOR, BBOX-EF, Fold, 1/2 w chocks
= Top of
lefts side fuel tank
- TRACTOR, BBOX-EF, Fix, 2 w chocks
= Left
frame front of fuel tank
- RIGID, 1 front axle, Fold, 1/2 w chocks
= Top of left
side battery box
- RIGID, 2 front axles, Fold, Frame free space, 2 wc = Top of
left side battery box
- RIGID, 2 front axles, Fix, W/o frame free space,2 wc = Left
frame behind 1st front wheel
Wheel chock(s) in the rear part of the vehicle
- RIGID, 1 front axle, Fix, 1/2 w chocks = Left frame rear (or
front) of rear wheels
Transport mounted wheel chock(s) in cab outer luggage
compartment
□ BLIGHT-E
Emergency brake light
□ FRACLOS
Frame end closing
□ WHCP-R
□ WHCP-T
■ Standard Equipment
Rims and Tyres
□ RT-SPOKE
■ RT-STEEL
Spoke rims on all axles
Steel rims on all axles
□ SPWT-D
□ SPWT-F
Spare wheel with tyre equal to drive
Spare wheel with tyre equal to front wheel
□ SWCP-T
Temporary spare wheel carrier.
Spare wheel is transport mounted (strapped on top of the
frame rails) with plastic stripes.
Spare wheel carrier transport mounted with the spare wheel on
top of the frame rails
□ SWCP-TP
■ JACK-20T
Jack 20 tonnes
■ TOOL-BAS
□ TOOLKIT
Basic tools (combination screw driver, socket wrench)
Extended tool kit
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
3 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
■ INFLAHOS
Tyre inflation hose (18 metres) with nozzles in both ends
□ GAUGE-TP
Tyre pressure gauge
□ OBDEP-C
EU6 mandatory on board diagnostics, phase C regulations
□ PTER1400
Powertrain equipment
□ ASO-C
□ ASO-ULC
One crawler gear
Two crawler gears, one ultra low crawler and one crawler
□ TRAP-HD
Reinforced gearbox application.
For manual gearboxes a heavy-duty nodular iron range
housing.
For I-shift gearboxes (2412 excl.) a reinforced gear shifting
system.
□ PVT-BAS
□ PVT-EXT
Basic topography information, learning by GPS positioning
Extended topography information, learning by GPS positioning
and centrally stored data
□
□
□
□
□
I-shift City gear changing software
I-shift construction gear changing software
I-shift distribution gear changing software
I-shift Heavy Duty gear changing software
I-shift Heavy Duty & Fuel Economy+ gear changing software
prepared for using GPS positioning (centrally stored road
memory, I-See)
I-shift long haul gear changing software
TP-BAS
TP-CON
TP-DIST
TP-HD
TP-HD3
□ TP-LONG
□ HPE-F101
□ HPE-F41
□ HPE-F51
□ HPE-F61
□ HPE-F81
□ HPE-T53
□ HPE-T70
□ HPE-V45
□ HPE-V75
□ PTPT-D
□ PTPT-F
□ AMSO-AUT
I-shift manual gear shift available in automatic mode incl
kickdown function
□ AVO-ENH
Enhanced I-shift software for construction and off road
applications
□ APF-ENH
Enhanced I-shift PTO functions (Auto Neutral / Reverse Inhibit
/ Split Box Connection)
□ CD40B-O
■ CS43B-O
Double plate clutch, plate diameter 400 mm
Single plate clutch, plate diameter 430 mm
□ PTR-DM
□ RET-TPT
Retarder for hydraulic gearbox
□ PTR-F
□ TC-HWO
□ TC-MAOH2
Cooler for hydraulic gearboxes - water/oil
Extra high performance cooler for manual/I-shift gearboxes air/oil
Basic performance cooler for manual/I-Shift gearboxes water/oil
High performance cooler for manual/I-Shift gearboxes water/oil
□ TC-MWO
■ TC-MWOH2
■ 2COM1100
□ 2COMP900
Dual cylinder air compressor 760 cc / 1100 l/min
Dual cylinder air compressor 636 cc
□ CLU-AIRC
Air compressor clutch automatically declutched when not
needed in order to save fuel
■ AIRIN-HI
□ AIRIN-LO
High air intake
Low air intake
□ ACL1ST-S
Air cleaner with additional filter element (primary + secondary)
■ 24AL110B
□ 24AL120B
□ 24AL150B
Alternator 110 Ampere
Alternator 120 Ampere
Alternator 150 Ampere
□ CCV-C
■ CCV-OX
Closed crankcase ventilation
Closed crankcase ventilation with oil separator and a
maintenance free gas centrifuge
■ PRIM-EL
Electrical priming pump for fast and easy bleeding of the fuel
system
Manual priming pump for fast and easy bleeding of the fuel
system
□ PRIM-MAN
□ PTR-D
□ PTR-DH
□ PTRD-D
□ PTRD-F
□ HPG-F101
□ HPG-F41
□ HPG-F51
□ HPG-F61
□ HPG-F81
□ EIDLESD
shaft groove (female) for a close coupled pump (DIN 5462 /
ISO 7653)
Rear engine mounted clutch independent power-take-off with
flange connection (SAE 1410 / ISO 7647)
Rear engine mounted hydraulic pump F1-101, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-41, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-51, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-61, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-81, fixed
displacement, single flow
Rear engine mounted hydraulic pump F2-53/53, fixed
displacement, twin flow
Rear engine mounted hydraulic pump F2-70/35, fixed
displacement, twin flow
Rear engine mounted hydraulic pump VP1-45, variable
displacement, single flow
Rear engine mounted hydraulic pump VP1-75, variable
displacement, single flow
Automatic gearbox driven power take-off, 1 front/upper
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 850
Nm).
Automatic gearbox driven Power take-off, 1 front/upper rear
facing flange connection (SAE 1410 / ISO 7647) for propeller
shaft (max. 850 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 1000
Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 600
Nm).
Mechanical gearbox driven medium speed power take-off, 1
rear connection (DIN 5462 / ISO 7653) for plug-in pump (max.
600 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft
(max. 1000 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
and 1 front connections (DIN 5462 / ISO 7653) for plug-in
pumps (max. 870 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft
(max. 870 Nm).
Gearbox mounted hydraulic pump F1-101, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-41, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-51, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-61, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-81, fixed displacement,
single flow
Engine idle shut down
Cab Interior, Driving
□ DRC-AMII
■ DRC-AUTO
Regeneration control of diesel filter particulates - auto initiation
/ manual on demand / manual inhibition
Regeneration control of diesel filter particulates - fully
automatic (in motion)
■ STWPOS-L
Left hand drive
□ STWM-LE
Leather steering wheel
Mechanically adjustable steering wheel with neck tilt
Mechanically adjustable steering wheel
□ AF-R
Hot fuel recirculation heated fuel filter
■ EST-AID
Engine start pre-heating element
□ STGW-AD2
■ STGW-ADJ
□ 220EBH15
Engine block heater, 220 volt, 1.5 kW
□ AIRBAG
Airbag on driver side
□ PTER-100
Rear engine mounted clutch independent power-take-off with
flange connection (DIN 100 / ISO 7646)
Rear engine mounted clutch independent PTO with splined
□ INST-BAS
Basic level instrument cluster - 4 inch monochrome display
240x320 pix
□ PTER-DIN
■ Standard Equipment
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
4 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
■ 1DAYDIG
□ 1DAYDIG2
One day digital tachograph, EC approved
Gen 2 one day digital tachograph, EC approved
□ ARSL
Additional road speed limiter (switch in dashboard)
□ CRUIS-E
■ CRUISEC
Cruise control I-Cruise with controls in the steering wheel,I-Roll
incl. Adding PVT-EXT gives I-See.
Basic cruise control with controls in steering wheel
□ RSENS-W
Wiper rain sensor
Cab Interior, Living
□ CU-ECC
□ CU-ECC2
□ UPHTRI10
■ CU-MCC
Fully electrically controlled air conditioning with sun sensor
Fully electrically controlled air conditioning with sun sensor,
mist sensor, air quality sensor and carbon filter
Electrical manually controlled air conditioning
■ IMMOBIL
Immobiliser
□ ALARM-B
□ ALARM-E
Burglar alarm - cab
Burglar alarm - cab/body/trailer
□ ALCOLOCK
Alcolock
□ PHONE-PK
Telephone preparation kit (antenna, antenna attachment, cable
from antenna to radio shelf).
□ WLIFT-AD
Electrical window lift, auto up/down driver side; el operated on
passenger side
Electrical window lift.
From the driver side both windows can be operated and from
the passenger side the passenger side window can be
operated.
■ WLIFT-EB
□ ISUNS-BS
■ ISUNS-DS
■ ISUNF-B
□ ISUNF-MD
□ ISUNF-RE
□ ISUNF-RM
Manually manoeuvred side interior sun visor (roller blind type)
on both sides
Manually manoeuvred side interior sun visor (roller blind type)
on driver side
Interior front plastic sun visors (driver and passenger side)
without mirror on driver side
Interior front plastic sun visors (driver and passenger side) with
mirror on driver side
Electrical textile interior sun visor (roller blind) integrated in
front shelf
Manual interior textile sun visor (roller-blind) integrated in front
shelf
■ CSPU-S
One open storage (behind push open lid) in upper part of dash
panel center section
□ ADFS
Two extra DIN slots in front shelf (push/pull storage),
165x40x180 mm (WxHxD)
□ BUPALARM
Back-up alarm
□ BUPMON
Back-up monitor including a 7 inch colour display integrated in
dashboard, Waeco CCD-camera (delivered loose in cab) with
a heated lens, motorised lens protection, 1 m pigtail cable
(front) and 10 metres chassis cable for tractor /20 metres for
rigid. Camera wirings not installed. Use PCA30081 for
installation.
□ RTOLL-PK
Preparation kit for road toll collect (GPS/GSM antenna and
cables)
□ LOADIND
Load indicator with dashboard display.
Measures axle pressures, load weight and total weight of truck
and one trailer.
□ REMC-MF
Wireless remote control - multi functional
□ FIREXT2G
□ FIREXT3S
Fire extinguisher 2 kg, German decal
Fire extinguisher 3 kg, Swedish/English decal
□ WARNVEST
Warning vest. Fulfils European standard according to EN 471
class 2.
■ WARNTRI2
Two warning triangles
□ AIDKIT
First aid kit containing sticking plaster, washing and drying
pads, compresses, elastic bandages, respiratory mask, gloves
and scissors
First aid kit containing sticking plaster, compresses, elastic
bandages, gloves, scissors, triangular bandage, bandaging
cloths, adhesive tape and rescue sheet (German
□ AIDKIT1B
■ Standard Equipment
requirements)
□ WARNLAMP Portable warning lamp with batteries
□ LAMP-IN
Inspection lamp with 10 m cable
□ BULBKIT
Bulb and fuse kit
□ WRITEPAD
Writing pad with spring-loaded paper clip
■ UPHTRI11
□ UPHTRI12
□ UPHTRI13
□ UPHTRI14
■ DST-CF1
□ DST-CF4
□ DST-CF5
□ DST-CF6
Seat upholstery with black embossed textile insert, black vinyl
bolster and blue vinyl side insert & textile interior trim in
matching grey/blue nuances
Seat upholstery with light grey embossed textile insert, raven
metallic vinyl bolster and red vinyl side insert & vinyl/textile
interior trim in matching skylark/grey/black nuances
Seat upholstery with blue soft textile insert, black vinyl bolster
& textile interior trim in matching grey/black/blue colours
Seat upholstery with dark grey leather insert and black leather
bolster & vinyl/textile interior trim in matching grey/black
nuances
Seat with dark grey leather insert and black leather bolster &
textile interior trim in matching grey and black colours
Driver seat, comfort, suspended
Driver seat, comfort, suspended, belt in seat
Driver seat, comfort, suspended, belt in seat, electrically
heated
Driver seat, comfort, suspended, belt in seat, electrically
heated, ventilated
□ SBD-RED
Red safety belts, passenge and driver seats
□ SBPRE-DS
Driver seat belt pretensioner
□ PST-BENC
□ PST-CF4
□ PST-CF5
■ PST-STD2
□ PST-STD4
Bench passenger seat
Passenger seat, comfort, suspended, belt in seat
Passenger seat, comfort, suspended, belt in seat, electrically
heated
Passenger seat, regular, non suspended
Passenger seat, regular, suspended
□ SBPRE-PS
Passenger seat belt pretensioner
□ ARM-DBPS
Two armrests on driver seat and one (outer) on passenger
seat
Two armrests on both driver and passenger seats
Two armrests on driver seat
Two armrests on passenger seat
Single armrest (next to driver) on passenger seat
□
□
□
□
ARMRE-BB
ARMRE-DB
ARMRE-PB
ARMRE-PS
□ ARU-BAS
□ ARU-LEA
Vinyl armrest upholstery
Leather armrest upholstery
■ FMAT-RU2
Two black rubber floor mats with raised edges and an
extended side (FMX)
Two black rubber floor mats
Two dark grey textile floor mats and two black rubber floor
mats with an extended side (FMX)
Two textile (dark grey on FH/FM, black on FH16) and two
black rubber floor mats
□ FMAT-RUB
□ FMAT-T2E
□ FMAT-TX2
□ LBK-RES
□ LBK70
■ ULBK
□ MATL-FI
Lower fixed rest kit, foldable to rear wall
Lower fixed bunk, not foldable - 2000x700 mm. Safety net
included.
Without lower bunk
□ MATL-SF
Mattress lower bunk - firm for over approx. 100 kg, pocket
springs.
Mattress lower bunk - semi-firm up to approx 100 kg, pocket
springs.
□ OLMAT-BA
□ OLMAT-PR
Overlay mattress protector, 28 mm thick black textile
Overlay mattress protector, 35 mm thick black textile
□ TBK60F
Fixed top bunk 600x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
Fixed top bunk 700x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
□ TBK70F
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
5 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
□ PH-CAB2
□ PH-ENGCA
□ PH-SS
Cab parking heater, 2 kW
Engine and cab parking heater
Short stop heater
□ AUXFS
Extra cab side foot-step
□ GUARD-EH
Guard plate for cooling pipes and oil sump
Guide rail on day cab driver side
Side ladder and guide rail on on day cab driver side
□ SLCP-BAS
Basic sleeper control panel (controlling interior light, parking
heater, roof hatch and door lock)
□ SIDEH-B
□ SIDSTP-R
□ SAFE
Key operated safe box under bed (FH) or at bed end (FM)
■ BUGNET
Radiator screen / Mosquito net (PVC coated fibreglass) in front
of radiator
□ ETSB-F
□ ETSB-FR
□ ETSB-FRS
Storage on engine tunnel - on front top
Storage on engine tunnel - on front top and at rear cab wall
Storage on engine tunnel - on front top & at rear cab wall &
storage immersed into tunnel on RH side
Storage on engine tunnel - on front top and storage immersed
into tunnel on right hand side
Fixed engine tunnel storage box at rear cab wall
Storage on engine tunnel - at rear cab wall and storage
immersed into tunnel on right hand side
Storage on engine tunnel - immersed into tunnel on right hand
side
□ CTILTP-E
■ CTILTP-M
Electrical cab tilt pump
Manual cab tilt pump
□ FCABS-A
■ FCABS-M
Air front cab suspension
Mechanical cab suspension
□ RCABS-A
■ RCABS-M
Air rear cab suspension
Mechanical rear cab suspension
□ MIRCOMFX
El heated & operared robust main rear view mirrors, electrically
heated wide angle mirrors (both sides).
Close view mirror on passenger side.
Electrically heated robust main rear view mirrors and wide
angle mirrors (both sides). Close view mirror on passenger
side.
□ ETSB-FS
□ ETSB-R
□ ETSB-RS
□ ETSB-S
□ RUS-BAS
□ RUS-HIG
Rear cab upper storage 154 litres (300 mm high)
Rear cab upper storage 245 litres (440 mm high)
□ TABLE
Foldable and height adjustable table to be mounted to the
lower bunk
□ REF-ICPK
Refrigerator preparation kit, engine tunnel mounted
□ BOTH-D
One 1.5 litre plastic soft-drink bottle holder under dashboard
centre section
■ MIRSTDX
■ AMIR-F20
Front close view mirror above windscreen, passenger side
(radius 200 mm)
□ SUNV-H
Exterior transparent dark grey front sun visor
□ AD-ROOF
□ AD-ROOFB
Roof air deflector. Design (length, height etc.) automatically
calculated and varies depending on vehicle total height
(chassis height, cab type, tyres etc).
Roof air deflector with light box
□ AD-SIDEL
□ AD-SIDES
Long cab side air deflector
Short cab side air deflectors
■ HL-BAS2
□ HL-BASIC
Halogen H1 head lamps (heavy duty)
Halogen H7 head lamps
Two (driver and passenger side) reading lamps with flexible
arms (snake lamps) and led lamps fitted on side walls
□ HL-CLEAN
High pressure headlamp cleaner
□ HLP-ST
Steel headlamp protection
□ RH-ECS
□ RH-MSR
■ URH
Roof hatch - Electrically operated / Clear glass / Sliding
Roof hatch - Manually operated / Steel / Rear opening
Without roof hatch
■ HL-ADJ
Adjustable headlamps to adjust the height of the light beam
■ DRL-LED
□ SWIND-BS
□ SWIND-PS
Extra side window on both sides
Rear side window on passenger side
V-shaped ("V-light") day running light (LED).
Turned on low beam gives a dimmed "V-light".
□ ASL-RF2
□ VANMIR
Vanity mirror in front shelf lid.
In sleeper cab on passenger side and in high/extra high cabs
in middle section of the front shelf.
Two Hella H11 70W spot lamps in sign box (one on each side
of the Globetrotter sign)
Preparation kit for two spot lamps in sign box
□ COFMA-PK
Preparation kit (24V) for coffee maker
■ INLI-BAS
Interior white light with smooth light transition at on/off, no
dimming
Interior white and red (night) light with smooth light transition at
on/off
Interior white and red (night) light with smooth light transition at
on/off and dimmer
□ INLI-NL
□ INLI-NLD
□ ARL-FLEX
□ AS-FUS
□ INFOT-PK
□ ASL-RFPK
□ BEACOA2F
One extra shelf in each of the two front upper storage
compartments.
Only 1 shelf if microwave oven mounted in one of the two
compartments.
□ BEACOA2R
Preparation kit (bracket, security straps, power cable, antenna
cable and aux cable) for mounting of a television above driver
door.
□ BEACON-P
Cab Exterior
□ BEACONA4
■ PAICS-B
Basic painting in a lightning grey colour of cab surrounding
parts (mirror housings, insteps, bumper and if fitted bumper
spoiler and sun visor).
If fitted roof air deflector, side air deflector and chassis fairings
are always painted in cab colour.
■ GLAS-TIN
Tinted windows (front/side/rear)
□ AWIND-RF
Rear fixed window (without curtains)
□ DGLAS-L
Laminated door glass
■ LOCK-MAN
□ LOCK-MRP
□ LOCK-REM
Manual door locking
Manual door locking with internal remote control (from driver
side) of passenger door
Central door locking with remote control
■ BUMP-HD
Heavy duty front bumper
■ Standard Equipment
Two front roof mounted amber rotating beacon warning lamps.
Mounted on accessory bracket if ordered, otherwise on cab
roof on both sides of the hatch.
Two rear roof mounted (on accessory bracket) amber warning
lamps.
Rotating beacon lamps mounted on sleeper cab.
Flashing LED lamps mounted on high/extra high sleeper cabs.
Prepared wiring (switch and connected relay included) for
warning lamps on cab roof.
Max load 300 W.
Four roof mounted amber warning lamps.
2 front mounted (on accessory bracket if ordered) rotating
beacon lamps.
2 rear mounted (on mandatory accessory bracket) rotating
beacon lamps on sleeper cab.
2 rear mounted (on mandatory accessory bracket) flashing
LED lamps on high/xhigh sleeper cabs.
□ CABPT-R1
■ CABPT-R2
One front cab roof pass through on passenger side
Two front cab roof pass throughs, one on each side
□ SPOTP-F
□ SPOTP-R
□ SPOTP-RF
Spotlamp preparation in cab front, max 280W
Spotlamp preparation on cab roof, max 280W
Spotlamp preparation on cab roof and in cab front, max
2x280W
□ ROS-IL
Illuminated roof sign with switch in radio shelf. Switch for
turning on/off.
Wiring preparation kit (wires and switch) for cab sign or roof air
□ ROS-ILP
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
6 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
FMX D13 86 Rigid XX-High T-ride FM 86F R3CTX
deflector illumination
□ CSGN-FMX
FMX decal in the cab roof sign area
■ HORN-F1S
One front mounted (behind grille) single tone air horn, Jericho.
Operated by steering wheel buttons.
Two roof mounted single tone chromed air horns. Operated by
steering wheel buttons.
□ HORN-R2S
□ AUXL-SPK
Electrical preparation kit (wiring and a switch in dashboard) for
snow plough lights.
Preparation for installation of additional headlights and
additional turning indicators.
□ TAILPRE2
□ TAILPREP
Tail lift preparation kit, wireless remote operation
Tail lift preparation kit, wire remote operation
□ AESW2
Two Body builder bistable electrical switches (marked AUX1 /
AUX2)
Two Body builder bistable electrical switches (marked
AUX1/AUX2) and in an empty 4-group preparation another four
bistable switches with dummy switch caps
□ ANT-CBR
Right hand side roof mounted foldable antenna and cables for
CB radio, single aerial.
□
□
□
□
□
□
Front roof mounted accessory bracket
Front & middle roof mounted accessory brackets
Front & rear roof mounted accessory brackets
Middle roof mounted accessory bracket
Rear roof mounted accessory bracket
Rear & middle roof mounted accessory brackets
□ AUXSW-4
Reflecting white cab side stripes by-packed in cab
Reflecting yellow cab side stripes by-packed in cab
□ TGW-3GWL
■ TGW-PK
Telematics gateway with 3G modem and WLAN
Telematics gateway preparation kit
Superstructure preparations
□ FMS-PK
Fleet Management System gateway, preparation kit
□ SRWL-PK
□ DRUT
My truck app gives the driver instant status information and
control of the vehicle remotely from a smartphone or tablet.
The variant enables the My truck app to connect to the vehicle.
ACCBR-F
ACCBR-FM
ACCBR-FR
ACCBR-M
ACCBR-R
ACCBR-RM
□ REFS-TW
□ REFS-TY
□ SWL-2FW
□ SWL-2RW
□ SWL-4W
□ SWL-PK
Wiring preparation for chassis mounted working lamps and a
3-position switch (On/Off/Reverse auto on).
Max load 280W.
Two H3 70W white front chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Two H3 70W white rear chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Four H3 70W white front (2) and rear (2) chassis mounted
(LH/RH side) working lamps and a 2-position switch (On/Off)
Wiring preparation for chassis mounted working lamps and a
2-position switch (On/Off). Max load 280W.
□ WL-CHPK
Preparation kit (switch and cable) for working lamp, max 2x70
W. Connector on chassis at gearbox.
□ WLC-H2A
Two H3/70W working lamps with amber coloured lens high
mounted back of cab (switch incl).
Two H3/70W working lamps, white lens high mounted back of
cab (switch incl).
Preparation kit (cables and switch) for cab mounted chassis
working lamp. Max load 280W.
Preparation kit (cables and switch) for high mounted working
lamps back of cab (pass through in cab rear roof included).
Max load 280W.
Preparation kit (cables and switch) for low mounted working
lamps back of cab (pass through in cab rear wall included).
Max load 280W.
Preparation kit (cables and switch) for low and high mounted
working lamps back of cab (pass throughs in rear wall and rear
roof included). Max load 280W.
□ WLC-H2W
□ WLC-PKCH
□ WLC-PKH
□ WLC-PKL
□ WLC-PKLH
□ ECBB-BAS
■ ECBB-HIG
Body builder electrical centre without any body builder module
Body builder electrical centre with cab body builder module
□ BBCHAS1
One 7-pole connector for Body builder interface.
Wiring harness routed from the bodybuilder electrical
distribution box inside the cab to a connection point inside the
right frame rail beside the gearbox.
Three 7-pole connectors for Body builder interface.
Wiring harness routed from the bodybuilder electrical
distribution box inside the cab to a connection point inside the
right frame rail beside the gearbox.
□ BBCHAS3
□ BEPR-T2
Body builder electrical software preparation for tipper with
remote control
□ TD-BAS
■ TD-LED
Trailer detection without LED sensor
Trailer detection with LED sensor
□ FBA-BTF
□ FBA-BTSF
Lower front body attachments for torsionally flexible platform
body
Lower front body attachments for torsionally semi-flexible body
(van or curtainsider)
□ HBA-FSFB
□ HBA-SB
Holes for body attachments, flexible/semi-flexible body
Holes for body attachments, stiff body
□ RBA-T2
Lower rear body attachments for helper frame
■ Standard Equipment
□ AESW2PK
Wiring for 4 extra hardwired switches (from Body builder
electrical centre to switch positions)
Services
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
7 (7)
Ref: FM 86F R3CTX01 8CE 2017-09-04 ENGVT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement