Epson | 536Wi | Installation guide | Epson 536Wi Installation Guide

4 Use the Interactive Pen
Your projector came with one pen with an orange
colored end (Interactive Pen A). You can purchase a
second pen with a blue end (Interactive Pen B, part
number V12H667010). Make sure one AA battery is
installed in the pen.
• Hold the pen perpendicular to the board, as shown
below.
The projector’s built-in toolbar lets you annotate images
from other devices that have been connected to the
projector, such as a document camera, tablet, or other
source.
1
Battery cover
• To double-click, tap twice.
ress one of the source buttons on the remote
P
control to select the source for the image you want
to annotate.
Image from a
computer connected
to the Computer1
or Computer2 port
• To right-click, press the button on the side of the pen.
• To click and drag, tap and drag with the pen.
Battery
light
Button
• To turn on the pen, tap the pen tip or press the button
on the side of the pen. The green light comes on
briefly. If the battery is low, the light flashes.
touching it.
• When you are finished using the pen, simply place it in
an area away from the projection screen.
Note: The pen turns off automatically after about 20
minutes of inactivity. Tap the pen tip or press the button
on the side to turn the pen back on. Ready to Learn
More?
Image from an
external device
connected to the
USB port
Image from a computer with
an HDMI connection, or a
video player
• To move the cursor, hover over the board without
Two different toolbars are available in PC Free Annotation
mode, one for annotation mode and one for whiteboard
annotation mode.
• Annotation mode displays the built-in toolbar on
whatever image is being projected.
• To left-click, tap on the board.
Pen tip
536Wi
5 Use PC Free Annotation
Image from a computer or
tablet connected through a
wired or wireless network
To activate the toolbar, tap the board with the pen.
3
ap the
T
or
don’t see the
the
icon.
ote: If you only see the
N
PC Free Annotation mode.
4
o close the toolbar, select the
T
bottom of the toolbar.
icon to open the toolbar. If you
icon, tap the
icon and then tap
icon, you are already in
icon at the
Note: Many of the built-in tools are the same as Easy
Interactive Tools, but fewer functions are available.
Select annotation mode
Undo
Select the background
pattern*
Change custom pen
color and width
Select whiteboard
annotation mode
Redo
Use custom pen
Use highlighter
Use black, red, or blue
pen—select small dot
for thin line
Use black, red, or blue
pen—select large dot
for thick line
Erase—select small dot
for thin eraser
Erase—select large dot
for thick eraser
Hide toolbar after each
annotation
Clear all annotations
* In annotation mode, the
Close toolbar
select background tool does not appear.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 8/14 Printed in XXXXXX
CPD-41708
• With a computer, you can use Easy Interactive Tools.
This software lets you use the interactive pen as a
mouse to annotate, save, and interact with content
from your computer.
Connect your computer and turn on the projector
2
Make sure the software is installed
3
Calibrate
Command toolbar
• Using the remote control
4
Use the interactive pen
5
Use PC Free Annotation
Drawing toolbar
BrightLink Interaction
The projector control toolbar lets you control the
projector from the screen just as you would using the
remote control.
• Without a computer, you can use the toolbar that is
built into the projector (PC Free Annotation). This
lets you annotate images from a document camera,
tablet, DVD player, or other source connected to your
projector.
Need help?
All you have to do is call (800) 637-7661. This service is
available for the duration of your warranty period.
Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
1
or black screen or background pattern, and use the
pen to write or draw as you would on a chalkboard or
dry erase board.
The Epson® PrivateLine® service is for you!
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered
logomark of Seiko Epson Corporation. BrightLink and PrivateLine are registered
trademarks of Epson America, Inc.
Follow the steps on this card to get started with your
BrightLink:
• Whiteboard annotation mode lets you project a white
Change highlighter color
2
Start Here
The BrightLink interactive pen turns any wall or table into
an interactive area, with or without a computer.
You may also speak with a projector support specialist by
dialing (562) 276-4394 (U.S) or (905) 709-3839 (Canada).
Support hours are 6 AM to 8 PM, Pacific Time, Monday
through Friday and 7 AM to 4 PM, Pacific Time, Saturday.
Days and hours of support are subject to change without
notice. Toll or long distance charges may apply.
tudents and colleagues can connect their own
S
laptops and annotate on the fly using the built-in
toolbar, without installing software.
2 Make Sure Interactive Software Is Installed
1 Connect Your Computer and
Turn on the Projector
1
onnect the USB cable from the projector’s USB-B
C
port directly to any available USB port on your
computer.
5
isplay an image from your computer. If the image
D
doesn’t appear, try one of the following:
• On some Windows laptops, you may need to
hold down the Fn key on the keyboard and press
F7 or the function key that lets you display on
an external monitor. It may have an icon such as
, or it may be labelled CRT/LCD.
• On a Mac, you may need to open System
Preferences and select Displays. Click the
Arrangement tab and select the Mirror
Displays check box.
• Try pressing the Source Search button on the
remote control.
USB cable
2
onnect an HDMI or VGA cable from the projector to
C
your computer.
VGA
3
urn on the projector by pressing the
T
button on the remote control.
In Windows®, you may see messages about device
drivers or new hardware.
power
If you need to install the Easy Interactive Tools
software, do one of the following:
• Use the CD that came with the projector, labeled
“EPSON Projector Software for Easy Interactive
Function.”
OS X:
Look for the Easy Interactive Driver and Easy Interactive
Tools folders in the Applications folder on your hard drive.
If you see these folders, the Easy Interactive software is
installed.
Windows 8.x:
Navigate to the Apps screen and select Easy Interactive
Tools.
If the pen position and cursor location don’t match, you
can try auto calibration, or you can calibrate manually for
even greater accuracy. You don’t need a computer, and
you won’t need to calibrate again unless the projector or
image is moved, or the image is resized.
1
Here’s how to find out if the Easy Interactive Tools
software is installed on your computer. (If the software is
not installed, follow the steps in the next column.)
Other Windows versions:
Select
or Start > All Programs or Programs >
EPSON Projector > Easy Interactive Tools Ver. 3.
If you see Easy Interactive Tools Ver. 3, the software
is installed.
HDMI
4
You may already have interactive software on your
computer, or you may need to install it. For OS X, you
need the Easy Interactive Driver and Easy Interactive
Tools (or other interactive software). For Windows, you
only need Easy Interactive Tools (or other interactive
software).
3 Calibrate
Turn projector
on/off
To start calibration, do one of the following:
Select from various
image sources
connected to the
projector
• Press the User button to start auto calibration,
then wait until calibration is complete.
• Follow the steps below to calibrate manually.
2
Press the Menu button on the remote control, select
• Download the most up-to-date version from:
epson.com/brightlinkdownloads (U.S.)
epson.ca/brightlinkdownloads (Canada)
global.latin.epson.com/soporte (Latin America;
site available in Spanish).
or more information about Easy Interactive Tools, see
F
the online Easy Interactive Tool Tips sheet or the online
Easy Interactive Tools Operation Guide.
Note: To use third party annotation software, tap the
screen with the pen to activate the projector’s built-in
toolbar, then tap the
or
icon to open it. Tap the
icon to activate mouse control and use your third
party software.Ready to Learn More?
the Extended menu, and press
.
Access menu
system for
additional
adjustments
Switch between
computer and
interactive pen
Enter
3
Select the Easy Interactive Function setting and
press
.
Select Manual Calibration, then press
4
5
When you see this screen, press
.
Calibrate
Zoom in and out
Page through
documents
Temporarily
turn off image
and sound
Stop video action
to select Yes.
For more information on using the remote control:
• See the online BrightLink User’s Guide.
• Go to the training section and watch a video or two at
The default language of the menu system is English.
To select another language, press the Menu button
on the remote control. Select Extended and press
. Select Language and press
. Select your
language and press
. Press the Menu button to
exit the menu system.
Using the Remote
Control
epson.com/brightlinkvideos (U.S.) or
epson.ca/brightlinkvideos (Canada).
6
ouch the circles on the screen with the pen to
T
perform manual calibration.
For more detailed instructions, see the online BrightLink
User’s Guide.
2 Make Sure Interactive Software Is Installed
1 Connect Your Computer and
Turn on the Projector
1
onnect the USB cable from the projector’s USB-B
C
port directly to any available USB port on your
computer.
5
isplay an image from your computer. If the image
D
doesn’t appear, try one of the following:
• On some Windows laptops, you may need to
hold down the Fn key on the keyboard and press
F7 or the function key that lets you display on
an external monitor. It may have an icon such as
, or it may be labelled CRT/LCD.
• On a Mac, you may need to open System
Preferences and select Displays. Click the
Arrangement tab and select the Mirror
Displays check box.
• Try pressing the Source Search button on the
remote control.
USB cable
2
onnect an HDMI or VGA cable from the projector to
C
your computer.
VGA
3
urn on the projector by pressing the
T
button on the remote control.
In Windows®, you may see messages about device
drivers or new hardware.
power
If you need to install the Easy Interactive Tools
software, do one of the following:
• Use the CD that came with the projector, labeled
“EPSON Projector Software for Easy Interactive
Function.”
OS X:
Look for the Easy Interactive Driver and Easy Interactive
Tools folders in the Applications folder on your hard drive.
If you see these folders, the Easy Interactive software is
installed.
Windows 8.x:
Navigate to the Apps screen and select Easy Interactive
Tools.
If the pen position and cursor location don’t match, you
can try auto calibration, or you can calibrate manually for
even greater accuracy. You don’t need a computer, and
you won’t need to calibrate again unless the projector or
image is moved, or the image is resized.
1
Here’s how to find out if the Easy Interactive Tools
software is installed on your computer. (If the software is
not installed, follow the steps in the next column.)
Other Windows versions:
Select
or Start > All Programs or Programs >
EPSON Projector > Easy Interactive Tools Ver. 3.
If you see Easy Interactive Tools Ver. 3, the software
is installed.
HDMI
4
You may already have interactive software on your
computer, or you may need to install it. For OS X, you
need the Easy Interactive Driver and Easy Interactive
Tools (or other interactive software). For Windows, you
only need Easy Interactive Tools (or other interactive
software).
3 Calibrate
Turn projector
on/off
To start calibration, do one of the following:
Select from various
image sources
connected to the
projector
• Press the User button to start auto calibration,
then wait until calibration is complete.
• Follow the steps below to calibrate manually.
2
Press the Menu button on the remote control, select
• Download the most up-to-date version from:
epson.com/brightlinkdownloads (U.S.)
epson.ca/brightlinkdownloads (Canada)
global.latin.epson.com/soporte (Latin America;
site available in Spanish).
or more information about Easy Interactive Tools, see
F
the online Easy Interactive Tool Tips sheet or the online
Easy Interactive Tools Operation Guide.
Note: To use third party annotation software, tap the
screen with the pen to activate the projector’s built-in
toolbar, then tap the
or
icon to open it. Tap the
icon to activate mouse control and use your third
party software.Ready to Learn More?
the Extended menu, and press
.
Access menu
system for
additional
adjustments
Switch between
computer and
interactive pen
Enter
3
Select the Easy Interactive Function setting and
press
.
Select Manual Calibration, then press
4
5
When you see this screen, press
.
Calibrate
Zoom in and out
Page through
documents
Temporarily
turn off image
and sound
Stop video action
to select Yes.
For more information on using the remote control:
• See the online BrightLink User’s Guide.
• Go to the training section and watch a video or two at
The default language of the menu system is English.
To select another language, press the Menu button
on the remote control. Select Extended and press
. Select Language and press
. Select your
language and press
. Press the Menu button to
exit the menu system.
Using the Remote
Control
epson.com/brightlinkvideos (U.S.) or
epson.ca/brightlinkvideos (Canada).
6
ouch the circles on the screen with the pen to
T
perform manual calibration.
For more detailed instructions, see the online BrightLink
User’s Guide.
2 Make Sure Interactive Software Is Installed
1 Connect Your Computer and
Turn on the Projector
1
onnect the USB cable from the projector’s USB-B
C
port directly to any available USB port on your
computer.
5
isplay an image from your computer. If the image
D
doesn’t appear, try one of the following:
• On some Windows laptops, you may need to
hold down the Fn key on the keyboard and press
F7 or the function key that lets you display on
an external monitor. It may have an icon such as
, or it may be labelled CRT/LCD.
• On a Mac, you may need to open System
Preferences and select Displays. Click the
Arrangement tab and select the Mirror
Displays check box.
• Try pressing the Source Search button on the
remote control.
USB cable
2
onnect an HDMI or VGA cable from the projector to
C
your computer.
VGA
3
urn on the projector by pressing the
T
button on the remote control.
In Windows®, you may see messages about device
drivers or new hardware.
power
If you need to install the Easy Interactive Tools
software, do one of the following:
• Use the CD that came with the projector, labeled
“EPSON Projector Software for Easy Interactive
Function.”
OS X:
Look for the Easy Interactive Driver and Easy Interactive
Tools folders in the Applications folder on your hard drive.
If you see these folders, the Easy Interactive software is
installed.
Windows 8.x:
Navigate to the Apps screen and select Easy Interactive
Tools.
If the pen position and cursor location don’t match, you
can try auto calibration, or you can calibrate manually for
even greater accuracy. You don’t need a computer, and
you won’t need to calibrate again unless the projector or
image is moved, or the image is resized.
1
Here’s how to find out if the Easy Interactive Tools
software is installed on your computer. (If the software is
not installed, follow the steps in the next column.)
Other Windows versions:
Select
or Start > All Programs or Programs >
EPSON Projector > Easy Interactive Tools Ver. 3.
If you see Easy Interactive Tools Ver. 3, the software
is installed.
HDMI
4
You may already have interactive software on your
computer, or you may need to install it. For OS X, you
need the Easy Interactive Driver and Easy Interactive
Tools (or other interactive software). For Windows, you
only need Easy Interactive Tools (or other interactive
software).
3 Calibrate
Turn projector
on/off
To start calibration, do one of the following:
Select from various
image sources
connected to the
projector
• Press the User button to start auto calibration,
then wait until calibration is complete.
• Follow the steps below to calibrate manually.
2
Press the Menu button on the remote control, select
• Download the most up-to-date version from:
epson.com/brightlinkdownloads (U.S.)
epson.ca/brightlinkdownloads (Canada)
global.latin.epson.com/soporte (Latin America;
site available in Spanish).
or more information about Easy Interactive Tools, see
F
the online Easy Interactive Tool Tips sheet or the online
Easy Interactive Tools Operation Guide.
Note: To use third party annotation software, tap the
screen with the pen to activate the projector’s built-in
toolbar, then tap the
or
icon to open it. Tap the
icon to activate mouse control and use your third
party software.Ready to Learn More?
the Extended menu, and press
.
Access menu
system for
additional
adjustments
Switch between
computer and
interactive pen
Enter
3
Select the Easy Interactive Function setting and
press
.
Select Manual Calibration, then press
4
5
When you see this screen, press
.
Calibrate
Zoom in and out
Page through
documents
Temporarily
turn off image
and sound
Stop video action
to select Yes.
For more information on using the remote control:
• See the online BrightLink User’s Guide.
• Go to the training section and watch a video or two at
The default language of the menu system is English.
To select another language, press the Menu button
on the remote control. Select Extended and press
. Select Language and press
. Select your
language and press
. Press the Menu button to
exit the menu system.
Using the Remote
Control
epson.com/brightlinkvideos (U.S.) or
epson.ca/brightlinkvideos (Canada).
6
ouch the circles on the screen with the pen to
T
perform manual calibration.
For more detailed instructions, see the online BrightLink
User’s Guide.
4 Use the Interactive Pen
Your projector came with one pen with an orange
colored end (Interactive Pen A). You can purchase a
second pen with a blue end (Interactive Pen B, part
number V12H667010). Make sure one AA battery is
installed in the pen.
• Hold the pen perpendicular to the board, as shown
below.
The projector’s built-in toolbar lets you annotate images
from other devices that have been connected to the
projector, such as a document camera, tablet, or other
source.
1
Battery cover
• To double-click, tap twice.
ress one of the source buttons on the remote
P
control to select the source for the image you want
to annotate.
Image from a
computer connected
to the Computer1
or Computer2 port
• To right-click, press the button on the side of the pen.
• To click and drag, tap and drag with the pen.
Battery
light
Button
• To turn on the pen, tap the pen tip or press the button
on the side of the pen. The green light comes on
briefly. If the battery is low, the light flashes.
touching it.
• When you are finished using the pen, simply place it in
an area away from the projection screen.
Note: The pen turns off automatically after about 20
minutes of inactivity. Tap the pen tip or press the button
on the side to turn the pen back on. Ready to Learn
More?
Image from an
external device
connected to the
USB port
Image from a computer with
an HDMI connection, or a
video player
• To move the cursor, hover over the board without
Two different toolbars are available in PC Free Annotation
mode, one for annotation mode and one for whiteboard
annotation mode.
• Annotation mode displays the built-in toolbar on
whatever image is being projected.
• To left-click, tap on the board.
Pen tip
536Wi
5 Use PC Free Annotation
Image from a computer or
tablet connected through a
wired or wireless network
To activate the toolbar, tap the board with the pen.
3
ap the
T
or
don’t see the
the
icon.
ote: If you only see the
N
PC Free Annotation mode.
4
o close the toolbar, select the
T
bottom of the toolbar.
icon to open the toolbar. If you
icon, tap the
icon and then tap
icon, you are already in
icon at the
Note: Many of the built-in tools are the same as Easy
Interactive Tools, but fewer functions are available.
Select annotation mode
Undo
Select the background
pattern*
Change custom pen
color and width
Select whiteboard
annotation mode
Redo
Use custom pen
Use highlighter
Use black, red, or blue
pen—select small dot
for thin line
Use black, red, or blue
pen—select large dot
for thick line
Erase—select small dot
for thin eraser
Erase—select large dot
for thick eraser
Hide toolbar after each
annotation
Clear all annotations
* In annotation mode, the
Close toolbar
select background tool does not appear.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 8/14 Printed in XXXXXX
CPD-41708
• With a computer, you can use Easy Interactive Tools.
This software lets you use the interactive pen as a
mouse to annotate, save, and interact with content
from your computer.
Connect your computer and turn on the projector
2
Make sure the software is installed
3
Calibrate
Command toolbar
• Using the remote control
4
Use the interactive pen
5
Use PC Free Annotation
Drawing toolbar
BrightLink Interaction
The projector control toolbar lets you control the
projector from the screen just as you would using the
remote control.
• Without a computer, you can use the toolbar that is
built into the projector (PC Free Annotation). This
lets you annotate images from a document camera,
tablet, DVD player, or other source connected to your
projector.
Need help?
All you have to do is call (800) 637-7661. This service is
available for the duration of your warranty period.
Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
1
or black screen or background pattern, and use the
pen to write or draw as you would on a chalkboard or
dry erase board.
The Epson® PrivateLine® service is for you!
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered
logomark of Seiko Epson Corporation. BrightLink and PrivateLine are registered
trademarks of Epson America, Inc.
Follow the steps on this card to get started with your
BrightLink:
• Whiteboard annotation mode lets you project a white
Change highlighter color
2
Start Here
The BrightLink interactive pen turns any wall or table into
an interactive area, with or without a computer.
You may also speak with a projector support specialist by
dialing (562) 276-4394 (U.S) or (905) 709-3839 (Canada).
Support hours are 6 AM to 8 PM, Pacific Time, Monday
through Friday and 7 AM to 4 PM, Pacific Time, Saturday.
Days and hours of support are subject to change without
notice. Toll or long distance charges may apply.
tudents and colleagues can connect their own
S
laptops and annotate on the fly using the built-in
toolbar, without installing software.
4 Use the Interactive Pen
Your projector came with one pen with an orange
colored end (Interactive Pen A). You can purchase a
second pen with a blue end (Interactive Pen B, part
number V12H667010). Make sure one AA battery is
installed in the pen.
• Hold the pen perpendicular to the board, as shown
below.
The projector’s built-in toolbar lets you annotate images
from other devices that have been connected to the
projector, such as a document camera, tablet, or other
source.
1
Battery cover
• To double-click, tap twice.
ress one of the source buttons on the remote
P
control to select the source for the image you want
to annotate.
Image from a
computer connected
to the Computer1
or Computer2 port
• To right-click, press the button on the side of the pen.
• To click and drag, tap and drag with the pen.
Battery
light
Button
• To turn on the pen, tap the pen tip or press the button
on the side of the pen. The green light comes on
briefly. If the battery is low, the light flashes.
touching it.
• When you are finished using the pen, simply place it in
an area away from the projection screen.
Note: The pen turns off automatically after about 20
minutes of inactivity. Tap the pen tip or press the button
on the side to turn the pen back on. Ready to Learn
More?
Image from an
external device
connected to the
USB port
Image from a computer with
an HDMI connection, or a
video player
• To move the cursor, hover over the board without
Two different toolbars are available in PC Free Annotation
mode, one for annotation mode and one for whiteboard
annotation mode.
• Annotation mode displays the built-in toolbar on
whatever image is being projected.
• To left-click, tap on the board.
Pen tip
536Wi
5 Use PC Free Annotation
Image from a computer or
tablet connected through a
wired or wireless network
To activate the toolbar, tap the board with the pen.
3
ap the
T
or
don’t see the
the
icon.
ote: If you only see the
N
PC Free Annotation mode.
4
o close the toolbar, select the
T
bottom of the toolbar.
icon to open the toolbar. If you
icon, tap the
icon and then tap
icon, you are already in
icon at the
Note: Many of the built-in tools are the same as Easy
Interactive Tools, but fewer functions are available.
Select annotation mode
Undo
Select the background
pattern*
Change custom pen
color and width
Select whiteboard
annotation mode
Redo
Use custom pen
Use highlighter
Use black, red, or blue
pen—select small dot
for thin line
Use black, red, or blue
pen—select large dot
for thick line
Erase—select small dot
for thin eraser
Erase—select large dot
for thick eraser
Hide toolbar after each
annotation
Clear all annotations
* In annotation mode, the
Close toolbar
select background tool does not appear.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 8/14 Printed in XXXXXX
CPD-41708
• With a computer, you can use Easy Interactive Tools.
This software lets you use the interactive pen as a
mouse to annotate, save, and interact with content
from your computer.
Connect your computer and turn on the projector
2
Make sure the software is installed
3
Calibrate
Command toolbar
• Using the remote control
4
Use the interactive pen
5
Use PC Free Annotation
Drawing toolbar
BrightLink Interaction
The projector control toolbar lets you control the
projector from the screen just as you would using the
remote control.
• Without a computer, you can use the toolbar that is
built into the projector (PC Free Annotation). This
lets you annotate images from a document camera,
tablet, DVD player, or other source connected to your
projector.
Need help?
All you have to do is call (800) 637-7661. This service is
available for the duration of your warranty period.
Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
1
or black screen or background pattern, and use the
pen to write or draw as you would on a chalkboard or
dry erase board.
The Epson® PrivateLine® service is for you!
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered
logomark of Seiko Epson Corporation. BrightLink and PrivateLine are registered
trademarks of Epson America, Inc.
Follow the steps on this card to get started with your
BrightLink:
• Whiteboard annotation mode lets you project a white
Change highlighter color
2
Start Here
The BrightLink interactive pen turns any wall or table into
an interactive area, with or without a computer.
You may also speak with a projector support specialist by
dialing (562) 276-4394 (U.S) or (905) 709-3839 (Canada).
Support hours are 6 AM to 8 PM, Pacific Time, Monday
through Friday and 7 AM to 4 PM, Pacific Time, Saturday.
Days and hours of support are subject to change without
notice. Toll or long distance charges may apply.
tudents and colleagues can connect their own
S
laptops and annotate on the fly using the built-in
toolbar, without installing software.
Download PDF

advertising