Epson | ELPMBPJF | User's Manual | Epson ELPMBPJF User's Manual

Installation and Assembly:
Universal Projector Ceiling Mount
Model: ELPMBPJF
R
Distributed by:
Epson America, Inc.
3840 Kilroy Airport Way
Long Beach, CA 90806
www.epson.com
This product is UL Listed. It must be
installed by a qualified professional
installer.
Maximum UL Load Capacity: 50 lb (22.7 kg)
Manufactured by Peerless Industries, Inc.
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your product until you have read and understood the instructions and warnings contained in this
Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care
at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power. See suggested torque values where applicable within these instructions.
Tools Needed for Assembly
•
•
•
•
•
stud finder ("edge to edge" stud finder is recommended)
phillips screwdriver
drill
1/4" bit for concrete surface
5/32" bit for wood joist
Table of Contents
Parts List .............................................................................................................................................................................. 3
Installation to Extension Column ........................................................................................................................................... 4
Installation to Wood Joist Ceilings ........................................................................................................................................ 5
Installation to Concrete Ceilings ............................................................................................................................................ 6
Flush Mount Application ....................................................................................................................................................... 7
Attaching Adapter Plate to Projector .................................................................................................................................. 7-8
Attaching Adapter Plate to Projector Mount .......................................................................................................................... 8
Projector Alignment and Accessories ................................................................................................................................... 9
Warranty Information ........................................................................................................................................................... 10
2 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Before you start check the parts list to ensure all of the parts shown are included.
Parts List
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Description
projector mount
4 mm security allen wrench
M5 x .8 x 10 mm socket pin type F screw
#10-32 x 3/8" spade thumb screw
#10-32 x 3/8" serrated washer head socket pin screw
#14 x 2.5" phillips hex head wood screw
ceiling plate
.25" ID x .56" OD x .26 spacer
extension column connector with cord management
#10-32 x 3/8" socket pin screw
#10-32 x 3/16" slotted set screw
adapter plate
M3 x 8 mm serrated washer head socket pin screw
M4 x 10 mm serrated washer head socket pin screw
M5 x 10 mm serrated washer head socket pin screw
M6 x 10 mm serrated washer head socket pin screw
2 mm security allen wrench
washer
Qty.
1
1
1
1
1
2
1
2
1
2
3
1
4
4
4
4
1
4
Part Number
055-0016
560-9646
520-2031
560-2107
520-2151
5S1-015-C04
580-4042
590-2071
580-4025
520-2084
520-2187
055-KUNV-S-2
510-2004
510-2060
510-2063
510-2066
560-1097
540-2025
NOTE: Actual parts may appear slightly different than illustrated.
A
L
I
C
E
J
M
F
H
R
B
N
G
O
P
K
D
Q
3 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Installation to Extension Column
1
Screw extension column (sold separately)
to ceiling plate (G). Align the notch with
one of the four holes in the ceiling
plate (G) and secure extension column
with a M5 x 10 mm socket pin screw (C)
using security allen wrench (B). See
detail 1.
EXTENSION
COLUMN
(ELPMBC01, UL Listed
EXT or ADJ Series)
(Sold Separately)
Screw extension column connector (I) to
extension column. Align slot in extension
column with one of the top holes in
extension column connector (I). Insert and
tighten one #10-32 x 3/8" socket pin
screw (J) through extension column
connector (I) into slot on extension
column using security allen wrench (B).
See detail 2.
G
K*
EXTENSION
COLUMN
DETAIL 1
SLOT
EXTENSION
COLUMN
Screw projector mount (A) into extension
column connector (I). Align slot in
projector mount (A) to one of the bottom
holes in extension column connector (I).
Insert and tighten one #10-32 x 3/8"
socket pin screw (J) through extension
column connector into slot in projector
mount (A) using security allen
wrench (B). See detail 3.
I
SLOT
K
J
I
SLOT
*NOTE: Slotted set screws (K) are used to
jam against the threads of each
connecting joint to prevent any excess
movement. Do not overtighten screws;
overtightening screws will damage threads
making it difficult to separate the products.
G
C
DETAIL 2
I
A
EXTENSION
COLUMN
Skip to step 2.
SLOT
K
J
A
DETAIL 3
4 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Installation To Wood Joist Ceilings
1
Drill two 5/32" (4 mm) dia. holes to a minimum depth
of 2.5" (64 mm). Attach ceiling plate (G) with two
#14 x 2.5" (6 mm x 65 mm) wood screws (F) as
shown using 3/8" (10 mm) socket wrench.
Skip to step 2.
WOOD
JOIST
WARNING
CEILING
• Tighten wood screws (F) so that wall plate (G) is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
G
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
WARNING
• It is the responsibility of the installer to verify that the
supporting surface will safely support the combined
load of all attached hardware and components.
F
IMPORTANT: Be sure to drill holes into the joist CENTER!
For optional Cord Management,
install two spacers (H) between ceiling
plate (G) and ceiling.
WOOD
JOIST
CEILING
H
H
G
F
5 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Installation to Concrete Ceilings
WARNING
• When installing Peerless mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in
the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet ASTM
C-90 specifications.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity of 50 lb (22.7 kg).
1
NOTE: ACC203 (Alligator concrete anchors are not
included) are recommended.
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (G) using two concrete
anchors and #14 x 2.5" wood screws (F) as shown in
Illustration A and 1, 2 and 3. Tighten all fasteners.
IMPORTANT: It is the responsibility of the installer to
verify that the ceiling will safely support the
combined load of all attached hardware and
components.
Skip to step 2.
1
concrete
surface
concrete
anchor
Drill holes and insert anchors
G
2
F
WARNING
concrete
anchor
Place ceiling plate over anchors and secure with screws
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
3
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
Tighten all fasteners
• FOR DIRECT ATTACHMENT TO LOAD BEARING
CONCRETE ONLY! Concrete expansion anchors are
not intended for attachment to concrete ceilings
covered with a layer of plaster, drywall, or other
finishing material. If mounting to concrete ceiling
covered with plaster / drywall is unavoidable, plaster /
drywall must be counterbored as shown below.
CUTAWAY VIEW
INCORRECT
metal
bracket
plaster/
dry wall
concrete
CONCRETE
ANCHOR
CONCRETE CEILING
CORRECT
metal
bracket
G
concrete
F
plaster/
dry wall
Illustration A
6 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Flush Mount Application
1
Screw projector mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling
plate (G) and secure projector mount (A) with a M5 x 10 mm socket pin screw (C) using security allen
wrench (B) as shown in detail 1.
NOTE: Slotted set screw (K) is used to jam against the threads of mount to prevent any excess movement of the
projector mount (A). Do not overtighten screw; overtightening screw will damage threads making
it difficult to separate the products.
C
K
NOTCH
WOOD
JOIST
A
CEILING
G
G
DETAIL 1
A
CAUTION
Attaching Adapter Plate to Projector
2
NOTE: The projector you are installing may differ in
appearance from the sample illustrated below.
• It is the responsibility of the installer to ensure that the
projector is properly ventilated. Feet of channels are
used to raise the mount off the projector surface.
NOTE: Some projectors may have three or four
attachment points. If projector has three attachment
points, the unused leg may be removed.
Place projector upside down. Locate adapter
plate (L) with notch* facing forward as close to
projector center of gravity as possible without
covering any mounting holes. Loosen channels, and
if there are only three mounting holes remove fourth
channel. Using one channel for each mounting hole,
position feet of channels over mounting holes as
shown. Important: If projector does not have at
least three mounting holes, do not use this adapter
plate. Once channels are in position retighten
fasteners.
NOTE: Some projectors have feet which can be
removed and the corresponding threaded insert can
be used for a mounting hole.
*Notch indicates front of projector.
MOUNTING
HOLE
L
*
*FRONT OF
PROJECTOR
7 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
3
Attach adapter plate (L) to projector using one
screw (M, N, O or P) for each channel as shown.
Tighten all screws, while keeping the center of gravity.
Be sure that adapter plate (L) is straight. Adjust the feet
of the channels to keep the adapter plate level. Tighten
all screws with 4 mm security allen wrench (B) or
wrench provided with projector mount, while keeping the
center of gravity. If M3 screws are used, tighten using 2
mm security allen wrench (Q).
NOTE: Projectors may require different size screws for
mounting. Use a combination of screws (M, N, O or P)
and foot adjustment that will result in channels of
adapter plate (L) fitting tightly against projector.
Important: In order to properly engage the threads in
the mounting holes, the screw must be turned at least
3 full turns.
NOTE: If using screw (M), place washer (R) between
screw (M) and foot of channel.
M,N, O
or P
LEG
L
FOOT OF
CHANNEL
Attaching Adapter Plate to Projector Mount
4
Attach projector, with adapter plate already on it,
to the projector mount (A) by inserting the
projector mount (A) into the adapter plate
connection and twisting until the adapter plate will
no longer turn (about 75°). The spring loaded
captive screw should line up with a corresponding
hole on the adapter plate (this should line up
automatically when the two are connected). Push
down and tighten the spring loaded captive screw
to secure the adapter plate to the mount. If not
using the optional security feature, fasten thumb
screw (D) in the hole opposite the spring loaded
captive screw.
E
CUTAWAY VIEW CEILING
OF CEILING
PLATE (G)
D
OD
WO ST
I
JO
CAPTIVE
SCREW
A
OPTIONAL: For security option, use #10-32 x
3/8" security screw (E) in the hole opposite the
spring loaded captive screw. Tighten with security
allen wrench (B). This will prevent the projector
from being removed.
NOTE: Be sure to only use the #10-32 x 3/8"
screw (E) (or the thumb screw (D) opposite
the spring loaded captive screw.
2
1
L
PROJECTOR
WARNING
• Do not lift more weight than you can handle! Use
additional man power or mechanical lifting equipment
to safely handle placement of the projector!
8 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Projector Alignment
5
To adjust roll, pitch and yaw loosen the set screw (shown
below) using allen wrench (B). You should be able to just
slightly loosen the screw so that your adjustments can
be set without having to hold the projector. Move projector
to desired position and slowly tighten set screw.
SET
SCREW
IMPORTANT: Allen wrench is your key for projector
removal. Store it in a safe place.
PROJECTOR
Accessories
NOTE: All accessories are available for purchase through Epson (www.epson.com)
ELPMBP02
False Ceiling Plate Kit
ELPMBP01
Adjustable Suspended Ceiling Channel Kit
• Mounts above 2' x 2' or 2' x 4' ceiling tile to structural
ceiling with tie wires
• Includes tie wire supports and flush
mount tube
• 1 ½" - 11.5" NPT fitting for attachment of
adjustable extension column
• Two knockout panels for electrical outlet
boxes
• 13.9" continuous, uninterrupted projector
adjustment
• Escutcheon ring included for a clean finish
• Max weight load: 60 lb (27 kg.)
• Color: White
• Replaces a 2' x 2' ceiling tile and mounts to
structural ceiling with tie wires
• Two-piece design offers five different
points for mount attachment
• Includes tie wire supports and flush mount
tube
• 1 ½" - 11.5" NPT fitting for attachment of
adjustable extension column
• Two knockout panels for electrical outlet boxes
• Max weight load: 50 lb (23 kg.)
• Color: White
R
ELPMBP03
Structural Round Ceiling Plate
R
ELPMBC01
Adjustable Extension Column (Pipe) 8" - 11"
• Mounts to wood joist or structural concrete ceiling
• Features cable management access hole
• 1 ½" - 11.5" NPT fitting for attachment of
adjustable extension column
• Max weight load: 150 lb (68 kg.)
• Color: White
• 8" - 11" adjustable extension in 1" increments
• Specially designed to allow internal cable
management
• 1 ½" - 11.5" NPT pipe threaded on both ends
• Notched ends for use with set screw to provide
safety and security
• Color: White
R
R
9 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
LIMITED FIVE-YEAR WARRANTY
3HHUOHVV,QGXVWULHV,QFHVWDEOLVKHVDZDUUDQW\SHULRGRIÀYH\HDUVIRUSURGXFWVPDQXIDFWXUHGRUVXSSOLHGE\3HHUOHVV7KLVSHULRGFRPPHQFHVIURPWKHGDWH
RIVDOHRIWKHSURGXFWWRWKHRULJLQDOFRQVXPHUEXWZLOOLQQRFDVHODVWIRUPRUHWKDQVL[\HDUVDIWHUWKHGDWHRIWKHSURGXFWҋVPDQXIDFWXUH'XULQJWKHZDUUDQW\
SHULRGVXFKSURGXFWVZLOOEHIUHHIURPGHIHFWVLQPDWHULDODQGZRUNPDQVKLSSURYLGHGWKH\DUHLQVWDOOHGDQGXVHGLQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVHVWDEOLVKHGE\
3HHUOHVV,QGXVWULHV,QF6XEMHFWWRDSSOLFDEOHOHJDOUHTXLUHPHQWVGXULQJWKHZDUUDQW\SHULRG3HHUOHVVZLOOUHSDLURUUHSODFHRUUHIXQGWKHSXUFKDVHSULFHRIDQ\
VXFKSURGXFWZKLFKIDLOVWRFRQIRUPZLWKWKLVZDUUDQW\
$Q\RWKHUZDUUDQWLHVSUHVFULEHGE\WKHODZZKLFKPD\DSSO\ZLWKUHVSHFWWRVXFKSURGXFWVDOVRDUHOLPLWHGLQGXUDWLRQWRWKHZDUUDQW\SHULRGVSHFLÀHGLQWKLV/LPLWHG
)LYH<HDU:DUUDQW\
7KLVZDUUDQW\GRHVQRWFRYHUGDPDJHFDXVHGE\DVHUYLFHRUUHSDLUVE\WKHFXVWRPHURUDSHUVRQZKRLVQRWDXWKRUL]HGIRUVXFKVHUYLFHRUUHSDLUVE\3HHUOHVV
,QGXVWULHV,QFEWKHIDLOXUHWRXWLOL]HSURSHUSDFNLQJZKHQUHWXUQLQJWKHSURGXFWFLQFRUUHFWLQVWDOODWLRQRUWKHIDLOXUHWRIROORZ3HHUOHVVҋLQVWUXFWLRQVRUZDUQLQJV
ZKHQLQVWDOOLQJXVLQJRUVWRULQJWKHSURGXFWRUGPLVXVHRUDFFLGHQWLQWUDQVLWRURWKHUZLVHLQFOXGLQJLQFDVHVRIWKLUGSDUW\DFWLRQVDQGIRUFHPDMHXUH
,QQRHYHQWVKDOO3HHUOHVVEHOLDEOHIRULQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVRUGDPDJHVDULVLQJIURPWKHWKHIWRIDQ\SURGXFWZKHWKHURUQRWVHFXUHGE\DVHFXULW\
GHYLFHZKLFKPD\EHLQFOXGHGZLWKWKHSURGXFW
7KLV/LPLWHG)LYH<HDU:DUUDQW\LVLQOLHXRIDOORWKHUZDUUDQWLHVH[SUHVVHGRULPSOLHGDQGLVWKHVROHUHPHG\ZLWKUHVSHFWWRSURGXFWGHIHFWV1RUHWDLOHUGHDOHU
GLVWULEXWRULQVWDOOHURURWKHUSHUVRQLVDXWKRUL]HGWRPRGLI\RUH[WHQGWKLVZDUUDQW\RULPSRVHDQ\REOLJDWLRQRQ3HHUOHVVLQFRQQHFWLRQZLWKWKHVDOHRIDQ\SURGXFW
PDQXIDFWXUHGRUVXSSOLHGE\3HHUOHVV
7KLVZDUUDQW\JLYHVVSHFLÀFOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVSURYLGHGE\WKHQDWLRQDOOHJLVODWLRQRIWKHFRXQWU\LQZKLFK\RXSXUFKDVHGVXFKSURGXFW
www.peerlessmounts.com
© 2007 Peerless Industries, Inc.
ISSUED 03/17/06 LIT-0190E
10 of 10
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 01-23-07 SHEET #:055-9498-1
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
© 2008, Peerless Industries, Inc. All rights reserved.
Epson is a registered trademark and Epson Exceed Your Vision is a trademark of Seiko Epson Corporation.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Download PDF

advertising