Model 652MK Recessed Mounting Kit

Model 652MK Recessed Mounting Kit
No. 652MK
RECESSED
MOUNTING KIT
For use with Nos. 652,653 Series Passive Infrared Motion Deteo
tars and (with No. 652MP Mounting Plate) No. 1852 PIR Detector.
Note: Model number denotes cover plate color as follows:
No. 652MK-WH(white); -BR(brown); -TN(tan); -BE(beige).
INSTALLATION:
The No. 652MK Recessed Mounting Kit has securing clips for mounting in wall surfaces up to 314” thick. As the
frame is only 2” deep, the kit can be installed in walls where 2” x 3” studs are used.
1. Cut 3.3/8”W X S’H opening in wall.
2 Remove detector’s cover.
3. Engage base of detector with its mounting plate fully, at least twice, to “break in” its base slots.
4. Fasten dtitector’s mounting plate to No. 652MK’s frame, using 3 screws supplied.
5. .Hold securing clips in ins&on position shown in Diagram 1 and insert frame In opening. Turn securing
screws clockwise to move securing clips into place and toward inside of wall surface. Before tightening completely, make sure the frame is straight.
6. Route wires through wiring entry openings near bottom of frame and in base of detector.
7. Engage detector’s base slots with hook tabs on mounting plate. Slide base down firmly so interlock lever, if
present, can move’freely when cover is replaced (Diagram 2)
8. Seal the wire entry openings with caulking compound, silicone rubber or equivalent.
IMPORTANT: Sealing the wire entry openings is necessary to lessen the possibility of false alarms
caused by air drafts in the wall cavity.
9. Connect and replace detector’s cover.
10. Install No. 952MK’s cover plate as follows: Hook No. 952MK’s cover plate notch post onto frame’s upper
(spring) tab (Diagram 2), hotd plate vertically, slide down slightly, snap plate’s lower notches under frame’s
lower tabs and release.
OVER e
ALARM
DEVICE MANUFACTURING
A DIVISION
OF PITYWAY
165 Eileen Way, Syosset.
P9214
8/03
97
91
CO.
COAPORATION
New York 11791
Cowright (5:1993 PITTWAY CORPORATION
WALL
UPPER SECURING CLIP n
POSITIONING AN0
TIQHTENING
SCRI
____
-~~i~~..~w
UPPER SECURING Cl
(IN INSERTION POSIl
1 r
l%r
/
, FRYE UPPERF:ETENyz
(SPRING) TAB
‘PEA SECURING CLIP
DETECTOR MTG PLATE
SCREWS(3)
‘POSITIONING AND
FRAME UPPER
(SPRING) TAB -
MTG PLATE
.;CREWS (3)
e HOOK TABS (4)
10
NO. 652MK’s
COVER PLATE -
sNo. 652MK’s FRAME
*
I
DETECTOR MTG. PLATE
DETECTOR COVER -
ETECTOR
4SE
NO. 652MK’s FRAME
DETECTOR BASE
I ABS
1
(4)
INTERLOCK LEVER
(NO. 652,653 SERIES ONLY)
0
. LOWtiR SECURING CLIP
(IN lNSERTlON POSlTION) DETECTOR COVER SCREW
II.I.’
-I
LOWER SECURING CLIP
POSITIONING AND
TIGHTENING SCREW
LOWER SECURING CLIP
COVER PLATE
LOWER NOTCHES (2)
Ff3AME LOW;;;I TASS (2)
Olagram 1: NO. 652MK’s FRAME WITH DETECTOR
MOUNTlNG PLATE INSTALLED
,.
I
‘,.I
I._
I
WALL
Diagram 2: SIDE VIEW
,’
I
e
.
>
,,.1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising