PowerLite 935W
®
Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Video device
4
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them.
Press the
power button on the projector or remote control.
Power Button
Using the remote control
Power Light
Make sure the batteries are installed as shown (two AA batteries).
RCA video cable (composite video)
Connect the projector
S-Video cable
Audio cable
Choose from the following connections.
Connect the square end of a USB cable to the projector’s �
USB
TypeB (square) port. Connect the flat end of the cable to any USB port on
your computer.
Audio cable
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB TypeA (flat) port.
Windows® XP or later: After turning on the projector, follow
the on-screen instructions to install the Epson USB Display software
(EMP_UDSE.EXE; only on first connection).
Connect one end of a VGA cable to the projector’s Computer1 or Computer2
port, and the other end to your computer’s �
monitor port. If you are using
a notebook, switch it to external display (see “Troubleshooting”). You can also
connect an audio cable.
Turn projector on and off
language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your
language and press Enter. Press the Menu to exit the menu system.
Adjust the image
Control projector
volume
1If you don’t see an image, press the Source Search button on the
Access projector
menus
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the online User’s Guide for details.
2To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
For more information on using the remote control, see the online User’s
Guide.
External monitor, external speakers, and
microphone
Project wirelessly
You can also connect an external monitor, external speakers, and a microphone
to your projector to enhance your presentations. See the online User’s Guide for
details.
3
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector. The power light on the projector turns orange.
Follow the steps here to connect the projector wirelessly over an 802.11b,
802.11g, or 802.11n wireless network. You must install the optional Epson
wireless LAN module (part number V12H418P12). Your computer must have
a wireless card or built-in wireless interface, and be running Windows 8,
Windows 7, Windows Vista®, Windows XP Professional x64, or Windows XP, or Mac OS X 10.5.8 to 10.8.x.
Turn the zoom ring to reduce or enlarge the image.
Zoom ring
1
4
Rotate the focus ring to sharpen the image.
Turn off the projector and unplug the power cord.
2Slide the air filter cover latch and open the air filter cover.
Focus ring
5If your image looks like
Wired network
3
Open the A/V Mute slide all the way.
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely. Or press the or buttons on
the projector to correct it.
6If your image looks like
or
, press the
or
3Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
buttons on the
projector to correct it.
4
*412439300*
Navigate projector
menus
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n
wireless network. See “Project wirelessly” for instructions.
*412439300*
Choose which source
to display
Turn off projector
display and sound
projector or the remote control to select the image source.
Wireless network
You can connect the projector to your network using an Ethernet cable. ����
See
“Project over a wired network” on the back of this sheet for instructions.
5The default language of the menu system is English. To select another
HDMI cable
Camera, USB device, or Epson DC-06 document
camera
Monitor port
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Component video to VGA cable
USB port
Mac OS X 10.5.8 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
The power light flashes green, then stays on.
Note: To shut down the projector, press the
Computer
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the online User’s Guide for instructions.
Insert the wireless LAN module into the port.
PowerLite 935W
®
Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Video device
4
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them.
Press the
power button on the projector or remote control.
Power Button
Using the remote control
Power Light
Make sure the batteries are installed as shown (two AA batteries).
RCA video cable (composite video)
Connect the projector
S-Video cable
Audio cable
Choose from the following connections.
Connect the square end of a USB cable to the projector’s �
USB
TypeB (square) port. Connect the flat end of the cable to any USB port on
your computer.
Audio cable
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB TypeA (flat) port.
Windows® XP or later: After turning on the projector, follow
the on-screen instructions to install the Epson USB Display software
(EMP_UDSE.EXE; only on first connection).
Connect one end of a VGA cable to the projector’s Computer1 or Computer2
port, and the other end to your computer’s �
monitor port. If you are using
a notebook, switch it to external display (see “Troubleshooting”). You can also
connect an audio cable.
Turn projector on and off
language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your
language and press Enter. Press the Menu to exit the menu system.
Adjust the image
Control projector
volume
1If you don’t see an image, press the Source Search button on the
Access projector
menus
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the online User’s Guide for details.
2To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
For more information on using the remote control, see the online User’s
Guide.
External monitor, external speakers, and
microphone
Project wirelessly
You can also connect an external monitor, external speakers, and a microphone
to your projector to enhance your presentations. See the online User’s Guide for
details.
3
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector. The power light on the projector turns orange.
Follow the steps here to connect the projector wirelessly over an 802.11b,
802.11g, or 802.11n wireless network. You must install the optional Epson
wireless LAN module (part number V12H418P12). Your computer must have
a wireless card or built-in wireless interface, and be running Windows 8,
Windows 7, Windows Vista®, Windows XP Professional x64, or Windows XP, or Mac OS X 10.5.8 to 10.8.x.
Turn the zoom ring to reduce or enlarge the image.
Zoom ring
1
4
Rotate the focus ring to sharpen the image.
Turn off the projector and unplug the power cord.
2Slide the air filter cover latch and open the air filter cover.
Focus ring
5If your image looks like
Wired network
3
Open the A/V Mute slide all the way.
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely. Or press the or buttons on
the projector to correct it.
6If your image looks like
or
, press the
or
3Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
buttons on the
projector to correct it.
4
*412439300*
Navigate projector
menus
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n
wireless network. See “Project wirelessly” for instructions.
*412439300*
Choose which source
to display
Turn off projector
display and sound
projector or the remote control to select the image source.
Wireless network
You can connect the projector to your network using an Ethernet cable. ����
See
“Project over a wired network” on the back of this sheet for instructions.
5The default language of the menu system is English. To select another
HDMI cable
Camera, USB device, or Epson DC-06 document
camera
Monitor port
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Component video to VGA cable
USB port
Mac OS X 10.5.8 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
The power light flashes green, then stays on.
Note: To shut down the projector, press the
Computer
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the online User’s Guide for instructions.
Insert the wireless LAN module into the port.
5Replace the wireless LAN module stopper and secure it using the screw
you removed.
14 Select the Connection Mode setting and choose one of these options:
•Quick to connect the projector to one computer on the network (Ad
Hoc)
•Advanced to connect the projector to multiple computers on
5Select the Projector Name setting, press Enter, and enter a name (up to
Where to get help
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Manuals
16 characters long) to identify your projector over the network.
Note: See the online User’s Guide for information on adding passwords.
For more information about using the projector, click the icons on your
desktop to access the online manuals (may require an Internet connection). If
you don’t have icons to the manuals, you can install them from the projector
CD or go to the Epson website, as described below.
6
Telephone support services
the network (Infrastructure)
15
6
Close the air filter cover.
7
Plug in and turn on the projector.
If you selected Quick connection mode, select the Channel setting for
your wireless network, select the type of wireless network you are using
as the Wireless LAN Sys. setting, and turn on the SSID Auto Setting
setting. Then go to step 17.
•If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
•
If you’re not using the key, continue with the steps below.
9Press the Menu button on the remote control, select the Network
menu, and press Enter.
network you are using as the Wireless LAN Sys. setting, and then enter
your network SSID (up to 32 characters) as the SSID setting.
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7
to 4 PM, Pacific Time, Saturday
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address, as
needed.
17To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
18When you are finished, select Complete and press Enter, then press
19 Press the Menu button to exit the menu system.
Project over a wired
network
10
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
11 Select the Basic menu and press Enter.
1
Plug in and turn on the projector.
2Press the Menu button on the remote control, select the Network menu,
and press Enter.
AM
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
7
Internet support
Choose IP Settings and press Enter.
8If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
Enter again to save your settings.
20 See “Install network software” for additional instructions.
Choose Network Configuration and press Enter.
To use the Epson PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with
a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839
(Canada).
16If you selected Advanced connection mode, select the type of wireless
8To configure your projector for your wireless network, do one of
the following:
Select the Wired LAN menu and press Enter.
9To prevent the IP address from appearing on the network standby screen,
set the SSID Display and /or IP Address Display settings to Off.
10When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11Press the Menu button to exit the menu system.
12See “Install network software” for additional instructions.
Install network software
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with a link to your projector User’s Guide.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and
select your projector.
12Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the online User’s Guide for information on adding passwords.
13 Select the Wireless LAN menu and press Enter.
3
Select Network Configuration and press Enter.
4
Select the Basic menu and press Enter.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
•
On a Macintosh, select the Mirror Displays setting in the System
Preferences Displays utility.
EPSON, PowerLite, and EasyMP are registered trademarks, and EPSON Exceed Your Vision is a
registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 11/12
Printed in XXXXXX
CPD-38469
5Replace the wireless LAN module stopper and secure it using the screw
you removed.
14 Select the Connection Mode setting and choose one of these options:
•Quick to connect the projector to one computer on the network (Ad
Hoc)
•Advanced to connect the projector to multiple computers on
5Select the Projector Name setting, press Enter, and enter a name (up to
Where to get help
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Manuals
16 characters long) to identify your projector over the network.
Note: See the online User’s Guide for information on adding passwords.
For more information about using the projector, click the icons on your
desktop to access the online manuals (may require an Internet connection). If
you don’t have icons to the manuals, you can install them from the projector
CD or go to the Epson website, as described below.
6
Telephone support services
the network (Infrastructure)
15
6
Close the air filter cover.
7
Plug in and turn on the projector.
If you selected Quick connection mode, select the Channel setting for
your wireless network, select the type of wireless network you are using
as the Wireless LAN Sys. setting, and turn on the SSID Auto Setting
setting. Then go to step 17.
•If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
•
If you’re not using the key, continue with the steps below.
9Press the Menu button on the remote control, select the Network
menu, and press Enter.
network you are using as the Wireless LAN Sys. setting, and then enter
your network SSID (up to 32 characters) as the SSID setting.
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7
to 4 PM, Pacific Time, Saturday
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address, as
needed.
17To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
18When you are finished, select Complete and press Enter, then press
19 Press the Menu button to exit the menu system.
Project over a wired
network
10
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
11 Select the Basic menu and press Enter.
1
Plug in and turn on the projector.
2Press the Menu button on the remote control, select the Network menu,
and press Enter.
AM
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
7
Internet support
Choose IP Settings and press Enter.
8If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
Enter again to save your settings.
20 See “Install network software” for additional instructions.
Choose Network Configuration and press Enter.
To use the Epson PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with
a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839
(Canada).
16If you selected Advanced connection mode, select the type of wireless
8To configure your projector for your wireless network, do one of
the following:
Select the Wired LAN menu and press Enter.
9To prevent the IP address from appearing on the network standby screen,
set the SSID Display and /or IP Address Display settings to Off.
10When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11Press the Menu button to exit the menu system.
12See “Install network software” for additional instructions.
Install network software
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with a link to your projector User’s Guide.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and
select your projector.
12Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the online User’s Guide for information on adding passwords.
13 Select the Wireless LAN menu and press Enter.
3
Select Network Configuration and press Enter.
4
Select the Basic menu and press Enter.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
•
On a Macintosh, select the Mirror Displays setting in the System
Preferences Displays utility.
EPSON, PowerLite, and EasyMP are registered trademarks, and EPSON Exceed Your Vision is a
registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 11/12
Printed in XXXXXX
CPD-38469
Download PDF

advertising