audio menu options
CAUTION: Changes or modifications not
expressly approved by the party
responsible for compliance with the
FCC Rules could avoid the users’
authority to operate this equipment.
CAUTION: The monitor shall not be exposed to
dripping or splashing. No objects
filled with liquids, such as vases, shall
be placed on the Monitor
CAUTION: Do Not Place This TV on an
unstable cart, stand, or table. The
TV may fall, causing serious injury
to a child or adult, and serious damage
to the TV. Use only with a cart or stand
recommended by the manufacturer, or
sold with the TV
CAUTION: Installation on concrete wall has passed
UL safety test.
1
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE.DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.
WARNING: THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES SHALL BE PLACED ON THE APPARATUS.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT.
CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE
PERSONNELONLY.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING
ACTIVITIES, BUT CALL QUALIFIED ELECTRICIAN PERSONNEL.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED, REPLACE ONLY
WITH THE SAME OF EQUIVALENT TYPE.
2
IMPORTANT SAFETY INSTRUCTIONS
1
READ THESE INSTRUCTIONS
2
KEEP THESE INSTRUCTIONS
ON OR PINCHED PARTICULARLY AT PLUGS,
3
HEED ALL WARNINGS
CONVENIENCE RECEPTACLES, AND THE POINT
4
FOLLOW ALL INSTRUCTIONS
WHERE THEY EXIT FROM THE APPARATUS.
5
DO NOT USE THIS APPARATUS NEAR WATER
10. PROTECT THE POWER CORD FROM BEING WALKED
11. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED
Do not use this TV near water. For example, do not use near
a bathtub, washbowl, kitchen sink or laundry tub, in a wet
6.
BY THE MANUFACTURER.
12. USE ONLY WITH CART, STAND, TRIPOD, BRACKET, OR
basement, or near a swimming pool, and the like. The TV set
TABLE SPECIFIED BY THE MANUFACTURER, OR SOLD
shall not be exposed to dripping or splashing. No objects
WITH THE APPARATUS. WHEN A CART IS USED, USE
filled with liquids, such as vases, shall be placed on the TV
CAUTION WHEN MOVING THE CART/
set.
APPARATUS COMBINATION TO AVOID
INJURY FROM TIP-OVER.
CLEAN ONLY WITH DRY CLOTH
Do not place this TV on an unstable cart, stand, tripod,
Unplug the TV from the wall outlet before cleaning. Do
bracket, or table. The TV may fall, causing serious injury to
not use liquid cleaners or aerosol cleaners. Use a
someone, and serious damage to the appliance. A TV and
damp cloth for cleaning.
7.
cart combination should be moved with care. Quick stops,
DO NOT BLOCK ANY VENTILATION OPENINGS.
excessive force, and uneven surfaces may cause the TV and
INSTALL IN ACCORDANCE WITH THE
cart combination to overturn.
MANUFACTURER`S INSTRUCTIONS.
13.
UNPLUG THIS APPARATUS DURING LIGHTNING
Slots and openings in the cabinet back or bottom are
STORMS OR WHEN UNUSED FOR LONG PERIODS
provided for ventilation, to ensure reliable operation of the TV
OF TIME.
and to protect it from overheating. These openings must not
be blocked or covered. The openings should never be
blocked by placing the TV on a bed, sofa, rug, or other
similar surface. This TV should never be placed near or over
a radiator or heat resource. This TV should not be placed in a
built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's instructions
have been adhered to.
For added Protection for this TV receiver during a lightning
storm, or when it is left unattended and unused for long
period of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
TV due to Lightning and power line surges.
14. REFER ALL SERVICING TO QUALIFIED SERVICE
PERSONNEL. SERVICING IS REQUIRED WHEN THE
APPARATUS HAS BEEN DAMAGED IN ANY WAY, SUCH
8.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS
RADIATORS, HEAT REGISTERS, STOVES, OR OTHER
APPARATUS (INCLUDE AMPLIFIERS) THAT PRODUCE
HEAT.
9.
DO NOT DEFEAT THE PURPOSE OF THE POLARIZED
OR GROUNDING-TYPE PLUG. A POLARIZED PLUG HAS
TWO BLADES WITH ONE WIDER THAN THE OTHER. A
AS POWER-SUPPLY CORD OR PLUG IS DAMAGED,
LIQUID HAS BEEN SPILLED OR OBJECTS HAVE
FALLEN INTO THE APPARATUS, THE APPARATUS HAS
BEEN EXPOSED TO RAIN OR MOISTURE, DOES NOT
OPERATE NORMALLY, OR HAS BEEN DROPPED.
Note: All figures in the manual are for reference only, please
refer to the actual units to determine their appearance.
GROUNDING TYPE PLUG HAS TWO BLADES AND A
THIRD GROUNDING PRONG. THE WIDE BLADE OR THE
THIRD PRONG IS PROVIDED FOR YOUR SAFETY. IF
THE PROVIDED PLUG DOES NOT FIT INTO YOUR
OUTLET, CONSULT AN ELECTRICIAN FOR
REPLACEMENT OF THE OBSOLETE OUTLET.
3
CLEANING AND MAINTENANCE
The front of the display panel has been
of the same type, until the surface is dry.
specially treated. Wipe the panel surface gently
using only a cleaning cloth or a soft, lint-free
Do not scratch or hit the surface of the panel with
fingernails or other hard objects. Furthermore, avoid
cloth.
If the surface is particularly dirty, soak a soft, lint-free
cloth in a weak detergent solution and then remove
excess liquid. Use this cloth to wipe the surface of
contact with volatile substances such as insect
sprays, solvents and thinner; otherwise, the quality
of the surface may be adversely affected.
the display panel, and then wipe it with a dry cloth,
DEAR PROSCAN CUSTOMER
Welcome to the bright and vivid world of Proscan TV set. We hope that you will have many years of
enjoyment from your new select.
To obtain maximum benefit from your set. Please read this manual before making any adjustments and
retain them together with purchase receipt for future reference,
Please read all the safety and operating instructions carefully before begin.
4
Table of contents
TABLE OF CONTENTS
CAUTION AND WARNING…………………………………………………….…………..
1
IMPORTANT SAFETY INSTRUCTIONS…………………..………………..………..…..
3
CLEANING AND MAINTENANCE………………………………………….…………….
4
DEAR PROSCAN CUSTOMER……………………………………………….….……….
4
SAFETY PRECAUTIONS..…………………………………………………….…………..
6
INSTALLATION……………………………………………………………….….………....
7
Preparation for using your new TV ……………………………………….…………...
8
FRONT PANEL………………………………………………………….……….…………
8
REAR PANEL…………………………………………………………………….....……...
9
CONNECTIONS AND EXTERNAL INPUT SETTINGS…………………………..….……….
10
Using the Remote control…………………………………………………..……………
11
LEARNING ABOUT REMOTE CONTROL…………………………………..………………
11
REMOTE CONTROL INSTRUCTIONS………………………………………..…………….
12
Basic operation……………………………………..……………………..……………….
13
TURNING ON AND OFF THE TV…………….……………………………..……………….
13
CHOOSING TV CHANNEL………………………………………..………..……………….
13
SELECTING INPUT SOURCE……………………………………………..………………...
14
VOLUME ADJUSTMENT..............................................................................................
14
Setup menu operation……………………………………..………...……………………
15
ADJUST THE OSD SCREEN………………………………………….….………………….
15
SELECT ON SCREEN LANGUAGE…………………….…………….….………………….
16
PICTURE MENU OPTIONS ……………………………………………..…….…………….
16
AUDIO MENU OPTIONS…………………….…………………………..………….……….
17
SETUP MENU OPTIONS…………………………….…………………..………………….
18
FEATURE MENU OPTIONS……………………………………..……..……………..…….
20
VGA MENU OPTIONS…………………………………………………....……..……….….
25
YPBPR MENU OPTIONS………………………….…………………..…………………….
26
HDMI MENU OPTIONS……………………………………………..........….……………...
27
APPENDIX ……………………………………………………………..……..……………..
28
Troubleshooting……………………………………………………..…….………..………
28
Removing TV Stand……………………………………..……………………………….……………...
31
Wall Mounting Unit Specification………………….………….……………...…………......
32
Safety Warnings……………………………….……..……………...…………………...
33
Universal Remote Control Code List …………..…………………………………………................
33
TV Specification…………………………………………………..…………….…….………………….
34
5
Safety Precautions
SAFETY PRECAUTIONS
WARNING
KEEP UNNEEDED SMALL PARTS AND OTHER OBJECTS OUT OF THE REACH OF
SMALL CHILDREN. THESE OBJECTS CAN BE ACCIDENTALLY SWALLOWED. ALSO,
BE CAREFUL ABOUT PACKAGING MATERIALS AND PLASTIC SHEETS.
Set up
Do not place the TV set on sloped or unstable surfaces.
Do not place any objects on top of the TV set. If water spills onto the TV set or foreign objects get inside it,
short-circuiting may occur which could result in fire or electric shock. If any foreign objects get inside the TV set,
please consult an Authorized Service Center.
Do not cover the ventilation holes. Doing so may cause the TV set overheated and can cause fire or damage to the
TV set.
Avoid installing this product near electronic equipment that is readily affected by electromagnetic waves.
It may cause interference in image, sound, etc. In particular, keep video equipment away from this
product.
AC Power Supply Cord
Securely insert the power cord plug as far as it will go. If the plug is not fully inserted, heat may be generated which
could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.
Do not handle the power cord plug with wet hands. Doing so may cause electric shocks.
Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the
cable.
Do not make any modifications to, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull
the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage
to the cable is suspected, have it repaired at an Authorized Service Center.
If the TV set will not be used for a long period of time, unplug the power cord from the wall outlet.
If Problems Occur During Use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the TV set,
unplug the power cord immediately. Continued use of the TV under these conditions might cause fire or permanent
damage to the unit. Have the TV evaluated at an Authorized Service Center. Service to the TV by any unauthorized
personnel is strongly discouraged due to its high voltage dangerous nature. If water or foreign objects get inside the
TV set, if the TV set is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.
Contact an Authorized Service Center for any repairs that need to be made
6
Safety Precautions
When using the TV set
Do not bring your hands, face or objects close to the ventilation holes of the TV set. Top of the TV set is usually
very hot due to the high temperature of exhaust air being released through the Ventilation holes. Burns or personal
injuries can happen if any body parts are brought too close. Placing any object near the top of the TV could also
result in heat damage to the object as well as to the TV if its ventilation holes are blocked.
Be sure to disconnect all cables before moving the TV set. Moving the TV with its cables attached might damage
the cables which, in turn, can cause fire or electric shock.
Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning.
electric shocks can result if this is not done.
Clean the power cable regularly to prevent it from becoming dusty. Built-up dust on the power cord plug can
increase humidity which might damage the insulation and cause fire. Unplug the cord from the wall outlet and
clean it with a dry cloth.
This TV set radiates infrared rays; therefore, it may affect other infrared communication equipment. Install your
infrared sensor in a place away from direct or reflected light from your TV set.
INSTALLATION
Selecting a location for the TV
1.
Place the TV on the floor or on a sturdy platform in a location where light does not directly hit the screen.
2.
Place the TV far enough from the walls to allow proper ventilation. Inadequate ventilation may cause
overheating, which may damage the TV.
Note: Please contact local dealer for wall mounting.
Optional External Equipment
For best performance, video cables should utilize 75 ohm coaxial shielded wire. Cables are available from your
dealer or electronic supply store.
Before you purchase any cables, be sure you know what type of output and input connectors your various
components require. Also determine the length of cable you will need.
7
Preparation for using your new TV – Front Panel
FRONT PANEL
Familiarizing Yourself with the Main Hardware
(The picture of the product may vary depending on the model)
a.
Select signal input.
(It changes to “ENTER” function when main menu displays )
b.
Main Menu display and menu selection
c.
Channel up
d.
Channel down
e.
Volume up
f.
Volume down
g.
ON/OFF button
8
Preparation for using your new TV – Rear Panel
REAR PANEL
Rear panel
(The picture of the product may vary depending on the model)
HDMI Input
- Input1: J
- Input2: K
Component Input 1
- Video: E1, F1, G1
- Audio: B, B1
Component Input 2
- Video: E, F, G
- Audio: C,C1
Composite Input
- Video: L
- Audio: D, D1
S-Video Input
- Video: M
- Audio: D, D1
VGA Input
- Video: I
- Audio: H(3.5m plug)
OTHERS
- Power Input: A
- COAX Digital Out: N
- External Antenna: O
9
Preparation for using your new TV – Connections
CONNECTIONS AND EXTERNAL INPUT SETTINGS
1. Checking Items before Connecting
Please check the list below before connecting the product to other devices.
< Check items before connecting. >
Check the instruction manual when connecting external devices. External products sometimes have different
buttons and locations.
A.
Do not connect the power unless every connection is well connected. The product may be damaged if
turned
on while still in the process of being connected.
B.
Connect the left (white) and right (red) cables correctly to the sound cable.
C.
Check the terminals to connect the product to on the rear panel.
2. Connecting an Antenna
There are internal and external types of antenna.
< Connecting an Antenna>
Cable TV network
A.
Use a coaxial cable to connect the rear panel of the TV's [AIR] or [CABLE] terminals and the wall
mount or external antenna.
B.
When an Air signal is required, connect to the [AIR] terminal. If a Cable signal is required, connect to
the [CABLE] terminal. If both Air and Cable are available, and then connect both [AIR] and [CABLE]
terminals.
C.
Connect the TV power cord when connecting everything else.
CAUTION
Avoid bending the copper tip at the center of the coaxial cable.
10
Using the remote control – Learning about remote control
LEARNING ABOUT REMOTE CONTROL
1.
POWER: Power on/off
2.
EJECT: Press to eject the disk in DVD
drive(not available for this model)
3.
SLEEP: Press to select a preset time interval
to automatically shut the TV
4.
ASPECT: Press to adjust the screen size.
5.
DISPLAY: Press to Check your current mode.
6.
MTS: Press to select your favorite language in
digital broadcasting
7.
DTV: Press to change between Analog TV
and Digital TV.
8.
FAV: Add/delete the current channel to your
favorite channel.
9.
FAV.+: Press to view the next favorite channel.
10. FAV-: Press to view the previous favorite
channel.
11. Numberic Buttons: Press to change the
channel directly using the numberic buttons.
12. RECALL: Press to switch between the current
channel and the last channel.
13. -: When selecting a digital broadcast channel,
press the number, followed by “-” button,
followed by sub channel number.
14. EPG: One of signal channel EPG or Multi
channel EPG.
15. PICTURE: Press to change to a preset picture
mode.
16. SOUND: Press to change to a preset sound
mode.
17. INPUT: Press to Display a menu of all
available input sources, Also used to confirm
your choice in the on-screen menu
18. ENTER: Enter and confirm button.
19. UP/DOWN LEFT/RIGHT : The direction keys.
20. MENU: Press to display main menu.
21. MUTE: Press to temporarily switch the sound
off.
22. FREEZE: Press to freeze the current picture.
23. CC: Press to select Closed Caption.
24. VOL+/-: Volume control buttons.
25. CH+/-: Channel control buttons
11
Using the remote control – Remote control instructions
REMOTE CONTROL INSTRUCTIONS
< Inserting the batteries into the remote control >
1.
Push the back of the remote control
2.
Pull forward slightly.
3.
Insert two AAA 1.5V batteries.
4.
Ensuring the correct polarity (+/-).
5.
Close the lid.
CAUTION: Use only Alkaline Batteries.
z If the remote control is not working, see the checkpoints below.
z Are the polarities of the batteries (+, -) correct?
z Are the batteries worn out?
z Is there an AC power failure?
z Is the power cable plugged in?
z Is any special fluorescent or neon sign board turned on?
< Remote Control Reception Angle>
Use the Remote control within a range of 7~10m and at an angle of 30° to either side of the receiver.
CAUTION
z Used batteries should be recycled
z Kept out of children's reach.
z Do NOT use new and old batteries together.
z Change both batteries at the same time.
z When not using the remote control over a long time, remove the batteries from the unit.
z Use only Alkaline battery.
12
Basic operation – Choosing TV Channel
TURNING ON AND OFF THE TV
TURN ON LCD TV
1.
Connecting to the AC input cable to switch on LCD TV. At this time the TV will enter standby mode and indicator show
red.
2.
User POWER button or
button on the remote control can turn on LCD TV from standby mode.
TURN OFF LCD TV
1.
Press POWER button or
button on the remote control to enter standby mode. The indicator is red.
2.
Wait 5 second after switching off LCD TV then you can turn on LCD TV again.
CHOOSING TV CHANNEL
1.
2.
Using the CH + / CH - on the front panel or on the remote control.
z
Press CH + to increase channel number.
z
Press CH - to decrease channel number.
Using 0-9 digital buttons and – button
You can select the channel number by pressing 0 to 9
3.
Example:
IN ANALOG SIGNAL:
To select channel (e.g. Channel 22): Press 2 -> 2 ->ENTER,It will jump to 22-0 directly
IN DIGITAL SIGNAL:
To select digit channel (e.g. Channel 22-1): Press 2 -> 2 -> - > 1 ->ENTER,the program will appear immediately
NOTE: Sub channel number of analog channel is always zero. But when you in the digital signal, if you enter
physical channel number and not end with “ENTER”, channel selection will be made if there is no
operation within a few seconds.
13
Basic operation – Selecting input source
SELECTING INPUT SOURCE
You can select the input source by pressing the INPUT on the remote control or on the front panel.
VOLUME ADJUSTMENT
1.
Press VOL+/- to adjust the volume.
2.
If you want to switch the sound OFF, press the MUTE.
3.
You can cancel this function by pressing MUTE or VOL+/-
14
Setup menu operation – Adjust the OSD screen
ADJUST THE OSD SCREEN
Press the MENU button to display the main menu.
Use
/
/
/
buttons to select and adjust the available menus.
NOTE: The OSD (On Screen Display) function enables you to adjust the screen status conveniently
until it provides graphical presentation.
When the cursor stays on a main menu function(Picture, Audio, Setup or Feature), you need to use
ENTER or button to activate it. After activating, the cursor will go forward into the submenu,
which you can use to choose the concrete functions with
/
button.
15
Setup menu operation – Screen Language & Picture Menu Option
SELECT ON SCREEN LANGUAGE
NOTE: If you use your LCD TV for the first time, you should select the language which will be used
for displaying menus and indications
z
Press MENU to display the main menu.
z
Press
z
Use
/
/
repeatedly to select the SETUP MENU.
and ENTER to select MENU LANGUAGE.
Press ENTER button to select your desired language.
PICTURE MENU OPTIONS
NOTE: In this manual, the OSD (On Screen Display) may be different from your TV’s in colors.
Press the MENU on the front panel or on the remote control and then use
/
to select the PICTURE menu.
/
to select what you want to adjust in the PICTURE menu.
1. Use
2. Press ENTER button to adjust.
3. When you are satisfied with your adjustment. Press MENU to exit the main menu.
Picture Mode
Select the type of picture which best corresponds to your viewing requirements by selecting Picture Mode in PICTURE menu.
When you press
/
buttons on the remote control, may select the picture modes (User / Vivid / Bright / Standard).
16
Setup menu operation – Audio menu options
Contrast
Press ENTER button to select it and then use
/
to adjust the contrast of picture.
/
to adjust the brightness of picture.
/
to adjust the sharpness level of picture.
/
to adjust the color saturation
/
to adjust the tint of picture
Brightness
Press ENTER button to select it and then use
Sharpness
Press ENTER button to select it and then use
Color
Press ENTER button to select it and then use
Tint ( NTSC Input only)
Press ENTER button to select it and then use
Aspect Ratio
Press ENTER button to select the ratio of picture display such as Normal/Zoom/Wide and Cinema.
AUDIO MENU OPTIONS
Press MENU on the front panel or on the remote control and then use
1.
Use
/
/
to select the AUDIO menu.
to select what you want to adjust in the AUDIO menu.
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust
Audio Mode
You can select the type of sound which best corresponds to your listening requirements by selecting sound in SOUND menu.
You may select the sound mode directly by pressing the SOUND button on the remote control.
17
Setup menu operation – Setup menu options
Audio Language
Press ENTER to one of the audio language such as English/ French and Spain, but the condition is that the program system
has included the language code.
Bass
Press ENTER button to select it and then use
/
to increase or decrease the level of the lower-pitched sounds.
/
to increase or decrease the level of the higher-pitched sounds.
/
to adjust the audio output between left and right speakers.
Treble
Press ENTER button to select it and then use
Balance
Press ENTER button to select it and then use
Digital Audio Output
Press ENTER button to select the one of mode of the digital audio output such as PCM and RCW.
Auto Volume Adjust
Press ENTER button to adjust the volume automatically.(TV and HDMI input only)
SETUP MENU OPTIONS
Press MENU on the front panel or on the remote control and then use
/
to select the SETUP menu.
to select what you want to adjust in the SETUP menu.
1.
Use
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
/
to adjust
Tuning Band
Press ENTER button to select Air, Cable, Cable HRC, Cable IRC or Cable Auto.
DTV Signal
DTV Signal menu will show the intensity of DTV signal.
User can adjust the direction and orientation of external antenna by checking DTV Signal.
18
Setup menu operation – Setup menu options
Auto Ch Search
Press
/
to move the cursor to the item to be selected (item selected highlighted in yellow). Press ENTER key to
enter your selection and scan. After the scan is finished, the following menu will display. The channels found the
automatically saved as below:
Note: If you want you exit the Auto Ch Search during the Auto search process, press MENU twice to exit.
Add On Ch Search
When the channels are found, use ENTER to add it to the cannel list
Manual Ch Set
Press ENTER button to display a channel list that you can select channel as below:
Note: this image comes from a engineering sample. Please operate according to actual channel list in your TV.
Channel Labels
Allows you to name the channel that is selected. Use
/
to move and use
/
to change.
Menu Language
To select language of the OSD such as English/ French and Spain.
19
Setup menu operation – Feature menu options
Reset
Press ENTER to return to the factory setting.
FEATURE MENU OPTIONS
Press MENU on the front panel or on the remote control and then use
/
to select the FEATURE menu
1.
Use
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to select what you want to adjust in the FEATURE menu.
/
to adjust
Time Set
Time Set Mode
You can select one of auto and manual to set the time. When selected auto, the item of year/date and time will be
disabled and can not to adjust. When select the manual mode, you can press
/
/
/
to set the corresponding
functions.
Time Zone
Press ENTER button to select it and then use
/
to select the time zone such as Pacific/ Alaska/ Hawaii/ Eastern/
Central/ Mountain
20
Setup menu operation – Feature menu options
Sleep Timer
Press ENTER button to select it and then use
/
to select the amount of time before your TV turn off automatically
and press the ENTER that can select the 15’/30’/45’/60’/90’/120’/180’/240’ and OFF.
Advance Video Menu
Press ENTER to enter the advance video menu as below
z
Noise Reduction - Spatial: press
z
Noise Reduction -Speaker :press
/
to select on or off.
z
Noise Reduction-Temporal: press
/
to select on or off.
z
Color Temperature: press
z
3D Y/C: Enable/disable 3D digital comb filter for pressing
z
Blue screen: Select to turn on blue screen display when there is no signal. However we recommend not to
/
/
to select on or off.
to select one of Normal/ Cool and Warm.
/
to select on or off.
use blue screen long time. If the screen is not changed long time, it can hurt the panel.
Password Set
Press the ENTER to enter old password menu, and then input the number of 0-9 as below, and you can change the
password when you input the new on twice. And the original password is “0000”.
Note: In case of password oblivion or missing, we provide the all-purpose password 1470.
Parental Control
Press ENTER to enter the sub-menu and then uses the 0-9 to enter the correct password and the Parental Control Menu
will display.
21
Setup menu operation – Feature menu options
Note: Advanced Rating is only available in digital channel.
US Ratings
Press ENTER to enter the US Ratings as below
MPAA
Press ENTER to lock or unlock one of None/ G/ PG/ PG-13/ R/ NC-17 and X
z
None – No restrictions
z
G – General Audience. This contains little or no violence, no strong language, and little or no sexual dialog or
situations.
z
PG – Children under 13 should be accompanied by an adult.
z
PG-13 – Parental guidance suggested. Children under 13 should be accompanied by an adult.
z
R – Restricted. Viewers should be 17 or older.
z
NC-17 – not classified. Viewers should be 17 or older.
TV Rating
Press ENTER to lock or unlock one of TV-MA/ TV-14/ TV-PG/TV-G/TV-Y7 and TV-Y.
z
TV-MA – Mature audiences only. This program may contain mature themes, profane language, graphic
violence and explicit and explicit sexual content.
z
TV-14 – Parents strongly cautioned. This program may contain sophisticated themes, sexual content, strong
language and more intense violence.
z
TV-PG – Parents guidance suggested. The program may contain infrequent coarse language, limited
violence, some suggestive sexual dialog and situations.
z
TV-G – General audience. This contains little or no violence, no strong language, and little or no sexual dialog
or situations.
22
Setup menu operation – Feature menu options
z
TV-V7 – Directed for older children. Themes and elements in this program may include mild physical or
comedic violence, or may frighten children under the age of seven.
z
TV-Y – All children. The themes and elements in this program are specifically designed for a very young
audience, including children from ages two six.
Canadian Ratings
Press ENTER to enter the Canadian Ratings as below
Canadian English
Press ENTER to lock or unlock one of E/ C/ C8+/ G/ PG/ 14+/ 18+.
z
E – Expect No restriction.
z
C – Children
z
C8+ - Viewers should be 8 or order.
z
G – General Audience.
z
PG – Parental guidance suggested.
z
14+ - Restricted. Viewers should be 14 or older.
z
18+ - Restricted. Viewers should be 18 or older.
Canadian French
Press ENTER to lock or unlock one of E/ G/ 8 ans+/ 13 ans+/ 16 ans+ and 18 ans+.
z
E – Expect No restriction.
z
G – For all.
z
8 ans+ - Restricted. Viewers should be 8 or older.
z
13 ans+ - Restricted. Viewers should be 13 or older.
z
16 ans+ - Restricted. Viewers should be 16 or older.
z
18 ans+ - Restricted. Viewers should be 18 or older.
23
Setup menu operation – Feature menu options
Advanced Parental Lock
When select the ON for Advance Rating, the Advanced Parental Lock will display.
Digital Closed Captions
This menu allows you to set the closed caption, and press ENTER to enter Closed Caption Options menu as below:
z Style: press
/
to select one of Automatic and Custom, when you select automatic, the other are disable and
can not be adjusted.
z Size: press
/
to select one of Normal/ Large and Small.
z Font: press
/
to select one of Default and from Front 1 to Font 7.
z Text Color: press
/
to select one of Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
z Text Opacity: press
/
z Background Color: press
z Background Opacity: press
to select one of the Solid/ Flashing/ Transparent/ Translucent
/
to select one of Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
/
to select one of the Solid/ Flashing/ Transparent/ Translucent
z Edge Effect: press
/
to select one of the None/ Raised/ Depressed/ Uniform/ Left Shadow/ Right Shadow.
z Edge Color: press
/
to select one of Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
24
Setup menu operation – VGA menu options
VGA MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming VGA on the top-right screen.
to select what you want to adjust in the FEATURE menu.
1.
Use
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
/
to adjust
VGA Set
Press
button and then press ENTER to enter the VGA set menu as below
/
z H-Position
Press ENTER button to select it and then use
/
to adjust the horizontal position of the picture.
/
to adjust the vertical position of the picture.
/
to adjust the phase of the picture.
/
to adjust the clock of the picture.
z V-Position
Press ENTER button to select it and then use
z Phase
Press ENTER button to select it and then use
z Clock
Press ENTER button to select it and then use
Note:
Phase- This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Clock- This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal
25
Setup menu operation – YPBPR menu options
screen size also will change.
Position- This function is to adjust the picture to Left/ Right and Up/ Down as you prefer.
Auto Adjust
Press ENTER button to select it and then use
/
to do auto adjust that automatically adjusts the available options for the
best viewing configuration.
Setting
Press ENTER to do preset that can return to the factory setting.
YPBPR MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming “Component” on the top-right screen.
to select what you want to adjust in the FEATURE menu.
1.
Use
2.
Press ENTER button to select and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
/
to adjust
Component Set
Press
/
button and then use ENTER to enter the Component Set menu as below
26
Setup menu operation – HDMI menu options
HDMI MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming “Component” on the top-right screen.
1. Use
/
to select what you want to adjust in the FEATURE menu.
2. Press ENTER button to select and then use
/
to adjust
3. When you are satisfied with your adjustment, press MENU to exit the main menu.
Time Set
Press
/
button and then use ENTER the time set menu that allows you to set the time the TV will display.
Sleep timer
Press ENTER button to select it and then use
/
to adjust the amount of time before your TV turn off automatically and
press the ENTER that can select the 15min/30min/ 45min/60min/ 90min/120min/180min/240min and OFF.
Advance Video Menu
Press ENTER to enter the advance video menu.
27
Appendix-Troubleshooting
TROUBLESHOOTING
Identifying Problems
If there are any problems using the product, please first consult the list below. If the list below does not solve the problem, call our
Customer Service Center immediately.
Setup and Connection
The TV won't turn on. Check your power cable connection.
z
I can't view the Basic channels. Check the connection of the antenna cable.
z
I want to view cable channels. Register with your local cable company then connect their receiver to your TV.
z
I want to view satellite channels. Setup your Satellite parabola antenna then connect your satellite receiver to the TV.
z
Digital broadcasting is not functioning. Check your antenna cable connection. Check if the digital channel selection is correctly
connected to your antenna cable.
Menu and Remote Control
z
The Remote Control isn't functioning well.
Change the batteries.
Check the polarity of the batteries.
Check the angle of the remote control from the product or if there are any obstacles between the remote control and the
product.
Check if you have pressed the correct key for the correct option.
Try to a bright light position near TV's which transmit a strong light source on TV <remote receiver> window.
z
I cannot change channels with the remote control.
Press [TV/AV] and select <TV>.
Try to use the remote control for the cable or satellite receiver to change the channel.
z
External input channels cannot be selected.
Check your external input connection cable.
z
A Menu cannot be selected.
Check if the menu is grayed out, and if it is, that menu cannot be selected.
Screen
z
Poor picture
Is the power cord unplugged? Make sure the power cable is plugged in correctly, and then press the power of the remote
control.
z
Black picture
Check if external input mode is selected
Press [external input selection] and select TV
z
Lined and flickering picture.
Try to finely adjust the channel.
28
Appendix-Troubleshooting
Are there any TV waves flowing or cordless radio transmitting stations? Avoid using cordless phones, hairdryers or electrical
drills.
z
Disfunctioning channels.
Check if the channel has been selected correctly.
Try changing the position of the antenna.
z
Picture with white and black dots.
Check if your antenna is damaged or any connections are broken.
Replace your antenna.
z
Only certain channels are in black and white
Check if the program is being broadcast in black and white.
Try to check the hue or contrast.
z
The Sub-Screen is black.
Check the power of the external device connected to the TV.
If the power cord is disconnected, the screen will be black.
z
Automatic turn-on is inactive.
When turning off your TV, you need to use the remote control or press the power button on the TV. (If you pull the plug on the
TV, the settings will be deleted.)
Sound
z
Poor quality sound
Check if the program is in stereo. Stereo may not work well in areas with bad reception. Try using Mono for these areas.
z
Sound is malfunctioning while using a cable.
Check your sound connecting cable.
Check if other channels also have no sound
●
I can see images, but there is no sound.
Press the volume buttons to increase the sound.
Try watching a video (if the video has sound, check your cable company). If there is no problem with the cable receiver, then
call our customer service.
Check if press MUTE on the remote control..
z
There is a malfunction after the volume is increased
Try to adjust the external devices connected to the TV (Digital channel receiver, DTV, DVD, Cable channel receiver, video)
If you can adjust your sound, try to balance the volume of the TV and the external device.
Channel
z
The channels are not functioning.
Connect the antenna connectors again.
Set to memorize channels in the automatic channel setting again.
Query the particular broadcasting station.
z
A limited number of channels are not functioning.
Change the location or direction of the antenna.
Try to select a few channels using numbers and memorize them using the add/delete button.
Query the broadcasting station.
z
Only UHF (14~69) Channels are unavailable.
Check if the antenna is able to receive UHF.
29
Appendix-Troubleshooting
Monitor
z
The PC Screen continually appears and disappears.
Check the connection between the TV and the computer and see if the connector is locked.
z
A “There is no signal “message appears.
This happens if the signal from the video card is exceeded for the maximum resolution or frequency of the TV. Try to set the
maximum resolution or frequency for the TV.
See if power save mode of the PC functions properly.(This is deactivated when any key is pressed or the mouse is moved)
z
The screen looks like there is water flowing on it.
Check the connector connected to the TV.
z
The screen is unclear and blurry.
Change the frequency and phase adjustment. Change the Resolution and frequency to the standard limit.
z
Unstable and flickering screen.
The resolution and frequency of the PC's Graphics Card should be set within the TV's range. Check the TV menu’s current
mode and standard mode and set it up again.
z
Some modes in standard mode are not working.
Check the compatibility of the video card.
If it is not working for compatible hardware, try to upgrade the driver of the graphics card.
30
Appendix-Removing TV Stand
Removing TV Stand
If you decide to install the wall mount your LCD TV, always use a VESA standard wall mount appropriate
for the size and weight of the LCD TV.
CAUTION
z Be sure to follow the instructions. Incorrect installation of the stand/wall mount may result in the
TV falling over.
z Before attaching (or detaching) the stand, unplug the AC cord from the AC input terminal.
z Unplug and remove any cables and/or other component connectors from the rear of the TV.
NOTES
Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as
described in the instructions provided with the wall bracket. Extreme care should always be used when
removing the stand/wall mount to avoid damage to the LCD panel.
As shown below:
(The picture may vary depending on the model.)
PROCEDURE
1. Place the TV set on a surface that is totally stable, flat and smooth(such as a
table). The front panel of TV should face the surface. Remove 6 screws signed in red circles.
2. Draw out the stand gently.
31
Appendix-Wall Mounting Unit Specification
Wall Mounting Unit Specification
Unit Dimension(unit: mm)
405X200
Screw Diameter
Screw Length(unit: mm)
M5
14
Remark: The specification of screw is just used on the back cabinet.
NOTE: Wall mount bracket is not included with TV and mounting of wall mount bracket to wall may
vary depending on brand and size of bracket. Customer should consult bracket mounting
instructions that came with wall mount for specific information on how to mount bracket to wall.
Before reading the installing instruction, please notice:
A. The wall mount is not contained in the accessories sold with television. We only provide the installing
specifications but not the wall mount itself. If you need the mount, please consult with the local dealer
for the assorted fitting parts.
B. We strongly suggest to set the wall mount with equipments of specification we ordered. If not,
unappropriate installing may cause damage to both the device and yourself.
32
Appendix-Safety Warnings
SAFETY WARNINGS
1. Do not set up the wall mount by yourself. Please contact qualified professionals for installation.
2. The TV should not be mounted on walls or surfaces which have an angle more than 10 degrees with
vertical direction. Otherwise the TV set may fall.
3. The walls for mounting must have enough strength to hold the whole weight of TV set. For example,
concrete wall and brickwork are eligible. Do not place the mount on soft walls such as earth walls and
plasterboard.
4. If spare parts of different specifications(such as screws) are used during mounting, consult with
qualified professionals to make sure these parts are safe and effective.
5. Before attaching the base to wall, ensure the holes for anchors are in keeping with the installing rules.
Otherwise there may exist some potential problems.
6. Do not place any heating source under your television. Or else, it can cause fire.
7. Do not place the TV near anything dripping. Transducers and high voltage wires should be kept far
away from the apparatus too. Or else, it may cause creepage, electric shock or bad resonance.
8. Do not place TV in a location where collision or vibration is liable to happen.
9. In order to avoid unexpected falling of the TV set, do not put any strong force on TV or wall mount after
installing.
10. Be sure to unplug the TV before installing. Keep anything hard or sharp away from the screen panel to
prevent the scuffing.
11. After installing, if there is any need to move the cabinet, please contact the qualified professionals.
UNIVERSAL REMOTE CONTROL CODE LIST
For Universal Remote Control brands listed below, please use accompanying Proscan codes
and refer to your Universal Remote Control User Manual for basic instruction for changing TV code to
operate Proscan model.
z
z
z
Proscan codes for Sony TV = 8003, 8012, 8058
Proscan codes for Philips TV = 1005, 1006, 1007, 1035, 1064, 1216
Proscan codes for other universal remotes = 272, 132, 134, 116, 040, 016, 024, 056, 019, 262
33
Appendix-TV Specification
TV SPECIFACITION
Model
37LB30Q
Diagonal display size
37 inches
Television system
American TV standard ATSC /NTSC system
Audio multiplex
BTSC system
VHF: 2~13 UHF: 14~69 CATV: 1~125
Channel coverage
Digital Terrestrial Broadcast(8VSB): 2~69
Digital cable (64/256 QAM): 1~135
PC mode
640×480/60Hz, 800×600/60Hz, 1024×768/60Hz
YPbPr/YCbCr mode
480i/60Hz, 480p/60Hz, 720p/60Hz, 1080i/60Hz
HDMI Mode
480i/60Hz, 480p/60Hz, 720p/60Hz, 1080i/60Hz
Resolution
1366×768
Power source
AC 100 - 240 V, 50 - 60 Hz
Power consumption
Less than 160W
Audio power
8W + 8 W
RF input: Cable/ Antenna ×1
VIDEO input: VIDEO ×1
S-VIDEO ×1
COMPONENT ×2
Connection Interface
HDMI ×2
GRAPHIC input: Analog RGB 15pin ×1
AUDIO Input: AV Audio ×1
Component Audio ×2
PC Audio Input ×1
AUDIO output: Digital audio output ×1
TV Dimensions
Length: 37 inches
Package Dimensions
Length: 38.5 inches
Width: 11.2 inches
Width: 12.2 inches
NET Weight
42.9 lbs
Package Weight
51.7 lbs
Supplied accessories
Height: 26.7 inches
Height: 28.3 inches
User Manual, Warranty Card, Remote control, AC cord, Batteries, QSG,
Warranty Register Card
Design and specifications are subjects to change without notice.
CUSTOMER NOTICE: Use carefully when operating to prevent damage to the screen.
34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement