Actuators - Home of Technologies

Actuators - Home of Technologies
Actuators
Actuators, Dimmers, Presence Sensors , System components
Available inputs for digital contacts
Multifunctional 4 IN / 4 OUT
Multifunctional 8 IN / 8 OUT
Inwall 4 Analog IN or 4/8 Digital In - 4 Led Out Module
Inwall 3 IN - 2 Digital -1 Analog / 2 Out module - With IR receiver
IO88E01KNX - IO44E01KNX
ON / OFF or continuous switching (PWM) for electric valves
Roller shutters and blinds motor reductor
Fan Coil Actuator for 2/4 pipes systems for heating/cooling
with 3 speed motors)
Configuration range:
8 lights
4 lights - 2 shutters
4 shutters
8 traditional switches
50
AD84A02KNX
4 digital inputs to interface free potential contacts
4 led output channels at low voltage that can drive
LED for synoptics panels or switches
4 analog/digital inputs for free potential contacts
or temperature sensors
Configuration range:
8 input switch interface - 4 led output
2 local thermostats - 6 switches - 4 led output
4 thermostats sensor - 4 switches - 4 led output
2 local thermostats - 2 sensors - 4 led output - 4 switches
IO32D01KNX
1 analog input for temperature probe
2 relay output at 8A for lights (2), shutters (1),
valves (on/off or pwm)
2 digital inputs for switches.
IR Receiver Connection
Configuration range:
2 lights - 1 thermostat - 2 switches
2 valves - 1 thermostat - 2 switches
1 shutter - 1 thermostat - 2 up down switch
1 light - 1 valve - 2 switches - 1 thermostat
2 lights - 2 switches - 1 IR receiver
1 shutter - 2 switches - 1 IR receiver
51
Actuators
BUILDING
Compact Dimensions - 4 module
ACTUATORS - INTERFACE - PRESENCE SENSOR KNX
PUSH BUTTON INTERFACE 2 IN - 2 OUT LED / PUSH BUTTON INTERFACE 4 IN - 4 OUT LED
The product is dedicated to interface of clean contacts with 2 or 4 input channels, such as sensors, traditional buttons
and 2 or 4 low voltage/current output channels to drive LED signal indicator lamps.
ORDER CODES
Push Button Interface 2 IN - 2 OUT LED
Push Button Interface 4 IN - 4 OUT LED
IO22C02KNX
IO44C02KNX
TECHNICAL FEATURES
Dimensions
H: 43 x W: 36 x D: 17 mm
Mounting
Fit in all standard derivation boxes: 2-3 modules rectangular and
round
Connection
Bus line: 2 bus connection terminals, max wire section: 0,8mm²
Inputs and outputs: 12-pin plug connector wired with 0,2 mm²
Supply
From the KNX bus 21 .. 30 VDC SELV power
consumption <10mA
Specific inputs
2 or 4 digital inputs for clean contacts
Maximum length 10 meters twisted cables
Specific outputs
2 / 4 outputs for driving LED - Max 0.5 mA each
INWALL MODULE 3 INPUT /2 OUTPUT
shutter con-trol, scene recall and control, sequences of 3 objects. Analog input, can manage one temperature probe (with On/
RC01A01IRC
IRC Device
alternatively to the temperature sensor, can manage a Infrared Receiver (IRX) in order to forward to the bus up to 8 channel coming
from a Infrared Remote Control (IRC) with on/off commands, scenes, sequences of 2 objects, dimmer and shutter. Outputs include
switching function with timed delays, stair-case function, scene recall, lock or logic function.
ORDER CODE
Inwall Module 3 IN /2 OUT
IR00A01ACC
IRX Cabling
TS01A01ACC
Temperature probe
TS01B01ACC
External
temperature probe
IO32D01KNX
TECHNICAL FEATURES
Dimensions
52 x 28 mm Weight: approx. 50 g
Supply
Via bus EIB/KNX cable
Voltage 21..30V DC
Current Consumption EIB/KNX < 10mA
Digital Input
For free potential contacts (dry contacts)
Analog Input for Infrared Receiver (IRX)
These accessories must be used:
IR01A01ACC (IRX with cable and connector)
RC80A01IRC (IR remote control 8 channels)
Outputs
10 A cos 1 - 230 Vac
Max capacitance @230V: 21µF 5.000 cycles
Incandescent lamps max load: 1500W 50.000 cycles
Fluorescent lamps max load: 6 x18W 25.000 cycles
Halogen lamps max load: 500W 50.000 cycles
Gas discharge lamps max load: 200W 25.000 cycles
Voltage Scanning: 3,3 V DC (internally Generated)
AWG24 cables with 1800 mm length
Analog Input for temperature probe
For NTC temperature probe eelectron code
TS01A01ACC (range from -20°C to +100°C)
TS01B01ACC (range from -50°C to +60°C)
INWALL 8 INPUT - 4 LED OUTPUT MODULE
AD84A02KNX module includes 4 digital inputs to interface clean contacts and 4 analog or digital inputs for clean contacts or
channels to drive LED signal indicator lamps. Inputs 5 to 8, set as analog inputs, enable up to 2 temperature probes (with On/Off
threshold) and 2 thermostats to control heating and cooling equipments, valves, 2 and 4 pipes fan coils.
ORDER CODE
Inwall 8 Input - 4 Led Output Module
AD84A02KNX
TECHNICAL FEATURES
TS01B01ACC
External
temperature probe
53
Analog Inputs - Key Features:
sensor with Eelectron NTC sensor (cod.TS01A01ACC
& TS01B01ACC)
Digital Outputs - Key Features:
4 outputs for driving LED 0.3 mA / channel
Use with LED Eelectron (Code LD00A01ACC /
LD00A11ACC)
Wired with 0,2 mm² 18 WNG - inputs [01÷ 04]
Heating and cooling modes
Command with HVAC mode or setpoint
2 points ON / OFF and PWM control algorithm
3-speeds fancoil control
OFF mode on window open detection
Actuators
BUILDING
TS01A01ACC
Temperature probe
Dimensions
H 43 x W 36 x D 24 mm
12 Channels Configurable as:
[01 ÷ 04] 4 digital inputs (clean contacts)
[05 ÷ 08] 4 digital or analog inputs (for clean contacts or
temperature sensors)
[09 ÷ 12] 4 digital outputs (outputs for LED)
Digital Input - Key Features:
8 channels [01 ÷ 08] for clean contacts
Maximum length 30 m twisted wires - input [01 ÷ 04]
Maximum length 10m of twisted wires - inputs [05 ÷ 08]
Wired with 0,2 mm² - 18 cm length - inputs [01 ÷ 04]
Connection through 6-pin screw terminal - inputs [05 ÷ 08]
Blinds and shutters control
Scenarios
ACTUATORS - INTERFACE - PRESENCE SENSOR KNX
UNIVERSAL 8 IN - 8 OUT C-LOAD
UNIVERSAL MODULE 4 / 8 OUT
The DIN RAIL 4 and 8 Output Modules BO04A01KNX - BO08A01KNX are an EIB/KNX DIN rail mounting devices useful to
interface loads (e.g. lamps) for any kind of applications.
The DIN RAIL 8 Input / 8 Output Module IO88B02KNX-C is an EIB/KNX DIN rail mounting device useful to interface commands
(e.g. push buttons) or loads (e.g. lamps) for any kind of applications. The device is equipped with 8 binary inputs (clean con-
as output channels to drive LEDs in synoptic monitoring panels.
Relay from 5 to 8 are equipped with manual command and can be switched manually.
Device is intended to be installed on DIN rail.
ORDER CODE
model BO08A01KNX. Device is intended to be installed on DIN rail.
ORDER CODES
Universal Module 4 OUT
Universal Module 8 OUT
BO04A01KNX
BO08A01KNX
TECHNICAL FEATURES
Dimensions
(W x H x D): 72 x 90 x 58 mm
Mounting
4 modules DIN
Connection
Outputs: 2 screw connectors by channel max 4mm2
Supply
From KNX bus 21..30 V DC SELV
Features relay outputs:
Resistivei: max 16 A
Incandescent Lamps: max 10 A
Motors and motor reductors : max 10 A
Fluorescent lighting transformer electronic: max 4 A
Fluorescent lamps: (max 140 µF) max 3 A (700W)
Universal 8 IN - 8 OUT C-Load
IO88B02KNX-C
TECHNICAL FEATURES
Dimensions
(W x H x D): 72 x 90 x 58 mm
Mounting width: 4 DIN modules (1 SU=18mm)
Mounting
Bus Line: 2 Terminal of bus connection , Max section 0,8mm²
Outputs: 2 screw terminals by channel max. section 4 mm²
Inputs: 3 screw terminals every 2 inputs, max. section 4 mm²
Supply
From Bus KNX 21..30 V DC SELV
Features
8 binary inputs for potential-free contacts
Max length 30m twisted cables
Features relay outputs
Resistive: 16 A Max
Incandescent lamps: 10 A Max
Motors and motor reductors: 10 A Max
Fluorescent lighting transformer. Electronic: 6 A Max
Fluorescent lamps (Max. 140 µ) 700W Max
MULTIFUNCTIONAL 4 IN / 4 OUT - MULTIFUNCTIONAL 8 IN / 8 OUT
UNIVERSAL MODULE 12 OUT
BO12A01KNX is a Din Rail 12 output 16 A actuator, it can be used to control up to 12 independent loads / lights , control
up to 6 independent blind / roller shutters with mechanical end position. This device is intended to be installed on DIN rail.
The products IO44E01KNX & IO88E01KNX are an EIB/KNX DIN rail mounting devices useful to interface commands (e.g. push buttons)
or loads (e.g. lamps) for any kind of applications. The devices are equipped with 4 or 8 binary inputs (clean contacts) and 4 or 8 binary relay
ORDER CODES
BO12A01KNX
TECHNICAL FEATURES
Features relay outputs:
Resistive: max 16 A
Incandescent Lamps: max 10 A
Motors and motoreductor : max 10 A
Fluorescent lighting transformer electronic: max 4 A
Fluorescent lamps: (max 140 µF) max 3 A (700W)
Dimensions
(W x H x D): 90 x 159 x 58 mm
Mounting
9 modules DIN
Supply
From KNX bus 21..32 V DC SELV
Current Consumption <10mA
UNIVERSAL 4 IN - 4 OUT C-LOAD
The DIN RAIL 4 Input / 4 Output Modules IO44B02KNX-C is an EIB/KNX DIN rail mounting device useful to interface commands (e.g. push buttons) or loads (e.g. lamps) for any kind of applications.
The device is equipped with 4 binary inputs (clean contacts) and 4 relay outputs suitable for capacitive loads (-C code).
ORDER CODE
54
IO88E01KNX
TECHNICAL FEATURES
Dimensions (W x H x D): 72 x 90 x 58 mm
Mounting width: 4 (1 SU=18mm)
Mounting
Bus Line: 2 Terminal of bus connection , Max section 0,8mm²
Outputs: 2 screw terminals for channel Max. 4 mm²
Inputs: 3 screw terminals every 2 inputs, Max. 4 mm²
Supply
From KNX bus 21..30 V DC SELV
Features
4 or 8 binary inputs for clean contacts
Max length 30m twisted cables
Features relay outputs
Resistive Loads: 16 A Max - 230 VAC
Incandescent lamps:10 A Max
Motors : 10 A Max
Fluorescent lighting transformer 2 A Max
Fluorescent lamps: use always an external counter
The 3 channel Dimmer Module is designed to drive dimmerable lighting with KNX bus and allow dimming of incandescent
and halogen loads of 230V, BT and TBT. The product can control one (900 W), two (600+300 W) or three (3x300 W) independent
lighting circuits.Device is intended to be installed on DIN rail.
2 speeds. Devices are intended to be installed on DIN rail.
TECHNICAL FEATURES
Dimensions
(W x H x D): 72 x 90 x 58 mm
Mounting width: 4 DIN modules (1 SU=18 mm)
Connection
Bus line, bus connecting terminal, wire max section 0,8mm²
Outputs: 2 screw connectors by channel max section 4 mm²
Inputs: 3 connectors every 2 inputs, max. section 4 mm²
Power Supply
From KNX Bus 21..30 V DC SELV
IO44E01KNX
3 X 300W DIMMER MODULE
include switching function, scenarios, logic functions.
Universal 4 IN / 4 OUT C-Load
ORDER CODES
Multifunctional 4 IN / 4 OUT
Multifunctional 8 IN / 8 OUT
IO44B02KNX-C
ORDER CODE
3 x 300W Dimmer Module
Features
4 binary inputs for clean contacts
Max length 30m twisted cables
Features relay outputs
Resistive: 16 A Max
Incandescent lamps: 10 A Max
Motors and motor reductors: 10 A Max
Fluorescent lighting transformer. Electronic: 6 A Max
Fluorescent lamps (Max. 140 µ) (700W Max)
TECHNICAL FEATURES
Dimensions
(H x W x D) 85 x 105 x 60 mm
Mounting
Width 6 mod. DIN (um 18mm)
Connections
Bus line: 2 bus connection terminals, section 0,8 mm²
Outputs: 2 plug-in terminals for each channel section conductors
from 0.75 mm² to 2.5 mm²
Supply
From the KNX bus and power supply 230 V 50/60 Hz
DM03B02KNX
55
3 power outputs with the following characteristics
Power: 20 W to 300 W output with the possibility
of coupling
between them.
Power consumption without load 5 W
Control elements
1 button to set the maximum value of brightness
Max. or Min.
1 button for manual control of each output
Indicators
1 red LED for programming ETS
Actuators
BUILDING
Universal Module 12 OUT
ACTUATORS - INTERFACE - PRESENCE SENSOR KNX
3 OUT DIMMER 1-10V
ACTUATORS - INTERFACE - PRESENCE SENSOR KNX
ENERGY METER THREE PHASE WITH KNX INTERFACE
Dimmer used to control lighting circuits via a 1/10V connection, acting upon remote control dimmers or electronic ballasts.
Device is intended to be installed on DIN rail.
ORDER CODE
3 OUT Dimmer 1-10V
DM03C02KNX
TECHNICAL FEATURES
Dimensions
(H x W. X D) 86 x 72 x 66 mm
Mounting
Width 4 DIN modules
Connections
Bus line: 2 bus connection terminals, max section 0,8mm²
Outputs: 2 screw terminals for the relay contact and 2 for
the change
1-10v, up to section conductors. 2.5 mm²
Supply
From the KNX bus 21 .. 30 VDC SELV
3 power outputs with the following characteristics :
Incandescent 230V Max. 2300W
Halogen 2300W
Halogen lamps with magnetic transformer 1500 VA
1500W Halogen lamps with electronic transformer
1000W electronic ballast
3 outputs 50mA Max.
Control elements
1 button for programming ETS
1 button for setting the maximum value of brightness
Max. or min.
1 button for manual control of each output
Indicators
1 red LED for programming ETS
3 output status LEDs
ENERGY METER 80A MONOPHASE WITH KNX INTERFACE
Active energy meters for single phase AC with LCD display backlight for the display of values, an input for switching rates
between 2 and direct connection to 80A. The values of instantaneous power, KW / KVA h and score for tariff 1 and 2, are
sent via the supplied KNX bus interface.
ORDER CODE
PM10A01KNX
Energy Meter 80 A Monophase with KNX Interface
TECHNICAL FEATURES
Dimensions
Case - 3 modules DIN 43880
Fixing 35 mm DIN rail EN 60715
Depth 70 mm
Reference standards for active energy - EN 50470-1-3
reactive power - output pulse EN 62053-23-31
Functionality
Connection to single-phase 2-wires
Rates for active and reactive energy No. 2 T1 or T2
Supply
Power supply voltage 230 VAC
184 VAC voltage variation range ... 276 VAC
Nominal frequency 50 Hz
Power consumption (MaX.) 8 VA - 0.6 W
Overload
Permanent voltage Un 276 V / momentarily (1 s) 300 V
Permanent current Imax 80 A / momentary (10 ms) 2400 A
Accuracy at 23 ± 1 ° C refer to the nominal values
Energy and power according to EN 50470-3 active% ± 1 (B)
Energy and reactive power in accordance with EN 62053-23 ± 2%
Measuring inputs
Listing phase / W - direct
Current range (Ist ... IMaX) 0,025 direct connection ...
80 A
Frequency: 50 Hz
Input waveform - sinusoidal
Minimum current for the measurement of
energy (Ist) 25 mA
S0 output according to EN 62053-31
Pulse output for active energy and reactive
Quantity Pulse 1000 imp / kWh
30 ± 2 ms pulse duration
Power required min. 5 ... .230% ± 5 VAC / Vdd
Maximum Series Pulse ON (Max. 230 V AC / DC) 90 mA
Maximum Series Pulse OFF (leakage current Max. 230
VAC / DC) 1 µA
Optical Interface
Front Calibration (precision control) LED imp / kWh 1000
Active energy meter for three phase alternating with a backlit LCD display for displaying the values, an input for switching rates
between 2 rates and direct connection to 80 A. The values of instantaneous power, KW / KVA h and scored for rate 1 and 2,
are sent via the supplied KNX bus interface.
ORDER CODE
Energy meter three phase with KNX interface
PM30A01KNX
TECHNICAL FEATURES
Main Features
Case 5 DIN 43880 DIN modules
Fixing 35 mm DIN rail EN 60715
Depth 70 mm
Reference standards:
Active energy - EN 50470-1-3
Reactive energy - output pulse EN 62053-23-31
Functionality
Electricity network connection 4-wires
Rates for active and reactive energy No. 2 T1 or T2
Supply
Power supply voltage 230 VAC
Voltage variation range 184 VAC ... 276 VAC
Nominal frequency 50 Hz
Power consumption (Max.) 8 -0.6 W VA
Overload
Permanent voltage Un, phase / phase 480 V
1 second: phase / phase 800 V
Permanent phase/N 276 V
1 second: phase/N 300 V
Permanent current Imax 80A
Momentary (0.5 s) 120A
Momentary (10 ms) 2400 A
Accuracy at 23 ± 1 ° C refer to the nominal values
Energy and power according to EN 504703 active ± 1%
class 1 (B)
Energy and reactive power in accordance with EN
62053-23 class 2 ± 2%
Measuring inputs
Listing phase /N - direct
Current range (Ist ... Imax) direct connection
0,015... 80 A
Frequency: 50 Hz
Input waveform - sinusoidal
Minimum current for the measurement of
energy (Ist) 15 mA
S0 output according to EN 62053-31
Pulse output for active energy and reactive
Quantity impulse 500 imp / kWh
30 ± 2 ms pulse duration
Power required min. 5 ... .230% ± 5 VAC / Vdd
Optical interface
Calibration Front (precision control)
LED imp / kWh 1000
KNX-DMX INTERFACE
Interface between the KNX bus and the DMX512 bus. Combine items for building automation control devices dedicated to
enlightenment and special effects.One-way gateway that receives telegrams from the KNX bus and data bus to DMX512.
ORDER CODE
KNX-DMX Interface
IC00B01DMX
TECHNICAL FEATURES
Dimensions
107x75x31mm
Mounting
Width Mod 6. DIN
Operating Temperature
-5 ° C / 45 ° C
Control Elements
3 x 16 potentiometers, stepper positions
1 button (user), 2 LEDs (user)
1 button programming for KNX and LED
KNX Power
20 - 32V DC, 150 mW
Programming
Using the USB port
Supply
9-30V DC, 100mA, separated
KNX PRESENCE SENSORS - INWALL OR SURFACE MOUNT
or fully automatic mode with the constant adjustment of brightness (dimming), the third is to slave mode, the fourth is a per-
passing reference to enlightenment.
56
PD00C01KNX
KNX Presence Sensors - Surface Mount
PD00C02KNX
TECHNICAL FEATURES
Dimensions:
98 x 50 mm H - Model Code PD00C01KNX
80 x 84.5 mm H - Model Code PD00C02KNX
Supply
24VDC to KNX / EIB-Bus Network
Detection area:
360 ° circular
Range (diameter) in meters:
Sitting 4.00 m
Movement away 10.0 m
Movement approaching 6.0 m
Degree of protection:
FM IP20 / Class II / EC
Ambient temperature: -25 ° C to +50 ° C
57
Actuators
BUILDING
ORDER CODE
KNX Presence Sensors - Inwall
SYSTEM COMPONENTS
ACCESSORIES
EIB / KNX BUS CABLE
POWER SUPPLY 160 - 320 - 640 MA
Power supply for generating bus voltage on a line with a maximum current of 160, 320 or 640mA according to the model.
With integrated choke to decouple the power supply voltage from the bus. Connection with screw terminals. Mounting on
DIN rails EN 50022. Connection via bus terminal.
ORDER CODE
ORDER CODE
Double-bus cable 2x2x0, 8 coils 100mt
CV00A01KNX
160 mA Power Supply
PS00C01KNX
Double-bus cable 2x2x0, 8 coils 500mt
CV05A01KNX
320 mA Power Supply
PS00B02KNX
Double-bus cable 2x2x0, 8 coils 1000mt
CV10A01KNX
640 mA Power Supply
PS00B03KNX
Single bus cable 1x2x0, 8 coils 100mt
CV00A02KNX
Single bus cable 1x2x0, 8 coils 500mt
CV05A02KNX
Single bus cable 1x2x0, 8 coils 1000mt
CV10A02KNX
TECHNICAL FEATURES
Dimensions
H 90 x W 72 x D 58 mm for PS00C01KNX & PS00B02KNX
H 90 x W 110 x D 58 mm for PS00B03KNX
Mounting
Width (UM = 18mm) 4 mod. DIN (PS00B01KNX & PS00B02KNX)
6 mod. DIN (PS00B03KNX)
Connection
Bus line connecting terminal, wire max section 0,8mm²
Power supply 230V with plug-in terminals, cable max section
2,5mm²
Supply
Line voltage: 230V AC, 50-60Hz
Output voltage
29 ± 1V DC
Output current / model
Max 160mA, 320mA, 640mA with protection
against short circuit
Control elements
1 switch to reset output power
Reports
1 green LED for power bus
1 red LED for overload warning
BUS LINE COUPLER KNX
TECHNICAL FEATURES
Inner conductor:
Solid bare copper wire
Construction:
1x2x0,80 mm or 2x2x0,8 mm
Dielectric:
Classified
CEI 20-11 M1
According to:
IEC 60332-1, IEC 61034-1, IEC 61034-2,
IEC 60754-1, IEC 60754-2
Diameter
5,20 mm ± 0,20
Colour
Green (RAL 6018)
(LSZHFRNC)
Colours:
Red, Black or Red, Black, Yellow, White
Outer Jacket
(LSZHFRNC)
LC00A01KNX can be used as a line coupler to connect a line to a main line or as a backbone coupler to connect a main line
activating by a frontal button which is very useful in commissioning / installing phase or during system tuning.
ORDER CODE
LC00A01KNX
Bus Line Coupler KNX
TECHNICAL FEATURES
Dimensions
H 80 x W 36 x D 58 mm
Mounting
2 mod. DIN
Connections
KNX/EIB instabus terminal for superordinate and subordinate
line
Supply
From KNX bus 21..32 V DC SELV
Control elements
1 button: Programming for ETS
Indicators
LED Bus Stat Main green - Off: main line error - On: main line ok
LED Bus Stat Main red - On: manual overwrite active
LED Bus Stat Sub green - Off: sub line error or not connected
On: sub line ok
LED Group Address - Routing of group telegrams - Off: main
route all - Red: block
LED Physical Address - Routing of physical addressed
active - Green and yellow: route all - Yellow: block
Packages of 20 or 60 pcs LED with Blue or White light 3V wired red / black.
ORDER CODE
3v LED indicator light blue wiring red-black - 20 pcs
3v LED indicator light blue wiring red-black - 60 pcs
LD00A01ACC
3v LED indicator light white wired red-black -20 pcs
3v LED indicator light white wired red-black -60 pcs
LD00A11ACC
LD00A02ACC
LD00A12ACC
TECHNICAL FEATURES
Dimensions
3 mm x 4.3 mm (width and height) and 3.85 mm (radius)
Current: 20 mA
Reverse Voltage: 5 V
Luminous Intensity: 4000 Min - Max 9000mcd
BUS CONNECTOR
BUS Connector Red / Black for EIB / KNX, with direct plug connection. They can be connected up to 4 pairs of wires to a KNX
device can also be used as a branch terminal.
ORDER CODE
USB - IP - IP ROUTER INTERFACE / KNX
These devices allows the communication between computers, IP devices with the KNX bus system.
- KNX / USB 1.1 or 2 interface for direct connection to your computer
- KNX / IP interface for direct or LAN connection for programming or supervision of the KNX system.
- KNX / IP router, is used for connectionless and simultaneous transmissioni of KNX telegrams to several devices. It can
also be used as a programming interface KNX bus system
ORDER CODE
USB / KNX Interface
IP / KNX Interface
IP ROUTER / KNX Interface
3V LED INDICATOR
IN00A02USB
IN00A02IPI
IN00A01RIP
WG00A01ACC
Wago connector Red / Black Box 10 pcs
Wago connector Red / Black Box 500 pcs
WG00A02ACC
TECHNICAL FEATURES
Wire 22 to 18 AWG (0.6 - 1 mm)
EN detected voltage 100V
Rated current 6A
Stripping length from 5 to 6 mm
Weight 1.6 gr
Dimensions alt. x width. x depth.: 11.5 x 10 x 10 mm
TECHNICAL FEATURES
58
Supply
From the KNX bus 21 .. 30 VDC SELV <300 mW
Additional 5V DC <200 mW through USB for
KNX/USB interface
Additional 12/24 V DC for KNX/IP interface
Additional 12/24 V DC for KNX/IP Router
Indicators
1 green LED active connection
Actuators
BUILDING
Dimensions
Weight: 100 g Dimensions: H: 90 x W: 36 x D: 65 mm
Mounting
Width (UM = 18mm) 2 mod. DIN
Connections for USB / KNX
Bus line with bus connecting terminal, wire max section 0,8mm²
USB type B socket
Connections for Interface IP - IP Router / KNX
Bus line bus connecting terminal, wire max section 0,8mm²
Complementary power supply: 2-wire screw terminals with
max section 4 mm²
Network RJ45 LAN jack
59
Standard
PUSH BUTTON INTERFACE 2 IN / 2 OUT LED - PUSH BUTTON INTERFACE 4 IN / 4 OUT LED
IO22C02KNX - IO44C02KNX
43
16,8
BUS KNX
devices produced by some 130 leading manufacturers in electronics / devices, and more than 12 million nodes installed worldwide.
KNX is approved by:
1
2
3
4
5
6
7
8
9
10
11
12
36
European Standard (CENELEC EN 50090, CEN EN CEN 13321-1 and EN 1332-2 “KNXnet / IP”)
International Standard (ISO / IEC 14543-3)
NEro
BiANCo
giALLo
NEro
roSSo
ArANCio
NEro
VErDE
BLU
NEro
VioLA
grigio
Chinese Standard (GB / Z 20965)
U.S. Standard (ANSI / ASHRAE 135)
KNX
iNTErFACE
1
2
3
CoM 1
4
CoM 2
7
8
9
CoM 3
10
CoM 4
iN 1
oUT 2
iN 2
oUT 2
For more information see the Konnex website at: www.konnex.org
BUS LINE EXTENSION
INWALL MODULE 3 IN / 2 OUT
IO32D01KNX
The structure of a KNX installation comprises areas, lines and devices. Each line consists of a power supply that provides voltage (SELV 29V), and a maximum of
64 devices connected in any installation topology. More bus lines can communicate with each other through “Line / Area Couplers”. To achieve coupling between
15 lines, you need to create an Area composed of a total of 960 devices: this can be coupled to a maximum of 15 other Areas.
27.12
A bus line can have a maximum length of 1,000m (considered as the sum of all segments in the line), and the maximum distance between the adapter and the
farthest device or between two devices is 750 m.
Actuator
Push button interface
KNX
1
2
3
4
5
6
50.66
48.20
Power supply
OUT 1
COM
OUT 2
COM
IN
COM
IN
IN
OUT
NC
IN 1
IN 2
TS
Max 750m t
Max 1000 mt
TECHNICAL CHARACTERISTICS OF THE SYSTEM
INWALL 8 INPUT/4 LED OUTPUT MODULE
AD84A02KNX
43
24
BUS KNX
19
20
21
13
36
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
NEro/BLACK
BiANCo/WHiTE
giALLo/YELLoW
NEro/BLACK
roSSo/rED
ArANCio/orANgE
NEro/BLACK
VErDE/grEEN
BLU/BLUE
NEro/BLACK
VioLA/VioLET
grigio/grEY
KNX
1
2
3
CoM
iN
oUT
1
iN/TS 5
iN/TS 6
CoM
13
14
15
4
5
6
CoM
iN
oUT
2
iN/TS 7
iN/TS 8
CoM
16
17
18
7
8
9
CoM
iN
oUT
3
10
11
12
CoM
iN
oUT
4
UNIVERSAL 4 OUT / 8 OUT / 12 OUT
BO04A01KNX - BO08A01KNX - BO012A01KNX
Actuators
BUILDING
Power
Speed
60
61
UNIVERSAL 4 IN / 4 OUT C-LOAD - MULTIFUNCTIONAL 4 IN / 4 OUT
640 mA POWER SUPPLY
IO44B02KNX-C - IO44E01KNX
230VAC 50Hz
230Vac 16A
230Vac 16A
72
58
LN
L
N
PS00B03KNX
PE
230Vac 16A
230Vac 16A
1
23
45
67
P ower Suppl y
Power
8
Overload
17
19
20
21
62
45
35
91
Bus KNX
com 3 / 4
in 4 or out 4
com 1 / 2
18
oUT 4
in 3 or out 3
KNX interface
oUT 3
in 2 or out 2
in 1 or out 1
45
35
90
oUT 2
91
Reset
oUT 1
22
30 V DC
_ +
KNX
_ +
input
30 Vdc
or
107
output
62
Bus KNX
UNIVERSAL 8 IN / 8 OUT C-LOAD - MULTIFUNCTIONAL 8 IN / 8 OUT
BUS LINE COUPLER KNX
IO88B02KNX-C - IO88E01KNX
LC00A01KNX
230Vac 16A
230Vac 16A
72
230Vac 16A
58
58
35
230Vac 16A
230Vac 16A
230Vac 16A
230Vac 16A
230Vac 16A
17
18
20
21
22
23
24
25
15 16
26
27
Bus KNX
Bus KNX
36
45
oUT 8
com7/8
oUT 7
in7 or out7
oUT 6
com5/6
oUT 5
13 14
in8 or out8
11 12
in6 or out6
oUT 4
com3/4
com1/2
19
9 10
in5 or out5
8
oUT 3
in2 or out2
oUT 2
in1 or out1
interfaccia KNX
67
in4 or out4
45
in3 or out3
23
oUT 1
45
35
90
1
28
input
or
Main Line
output
Line
Bus KNX
USB/KNX INTERFACE
160 mA POWER SUPPLY
PS00C01KNX
L
230VAC 50Hz N
LN
IN00A02USB
USB Connection
17,5
PE
61
USB
Power
KNX
_ +
Bus KNX
30 V DC
_ +
71
62
Bus KNX
IP ROUTER /KNX INTERFACE - IP/KNX INTERFACE
320 mA POWER SUPPLY
TCP / IP Connection
35
PE
61
P ower Suppl y
Power
RJ45
Bus KNX
30 V DC
_ +
71
62
Bus KNX
62
63
Actuators
BUILDING
KNX
_ +
45
30 Vdc
35
Bus KNX
90
62
45
91
Reset
35
Overload
91
IN00A01RIP
IN00A02IPI
PS00B02KNX
L
230VAC 50Hz N
LN
45
30 Vdc
35
Bus KNX
90
45
35
91
91
Reset
62
Overload
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement