Euro-Pro | EP722 | User's Manual | Euro-Pro EP722 User's Manual

Euro-Pro EP722 User's Manual
OWNER’S MANUAL
Model EP722
120V., 60Hz., 10.8 Amps
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
www.sharkvac.com
IMPORTANT SAFETY INSTRUCTIONS
When using your vacuum cleaner, basic safety precautions should always be
observed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read all instructions before using your
canister vacuum.
Use the system only for its intended use.
To protect against a risk of electric shock,
do not immerse any part of the system in
water or other liquids.
Never yank cord to disconnect from
outlet; instead, grasp plug and pull to
disconnect.
Do not allow cord to touch hot surfaces.
Do not run appliance over cord.
Do not operate the system with a damaged
cord or plug, or if the appliance or any other
part of the system has been dropped or
damaged. To avoid the risk of electric
shock, do not disassemble or attempt to
repair the canister vacuum. Return the
system to EURO-PRO Corporation (see
warranty) for examination and repair.
Incorrect re-assembly or repair can cause a
risk of electrical shock or injury to persons
when the canister vacuum is used.
Close supervision is necessary for any
appliance being used by or near children.
Do not leave the system unattended while
connected.
Keep hair, loose clothing, fingers and all
parts of body away from opening and
moving parts.
Do not use to pick up flammable or
combustible liquids such as gasoline or use
in areas where they may be present.
Do not pick up anything that is burning or
smoking such as cigarettes, matches or hot
ashes.
Use extra care when cleaning on stairs.
Do not use the canister vacuum without the
dust bag and/or filters in place.
Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
This appliance is intended only for
household use. Follow all user instructions
in this manual.
To reduce the risk of fire, electric shock, or
injury:
• Do not leave the canister vacuum plugged
in when unattended. Unplug the electrical
cord when not in use and before servicing.
• Do not allow to be used as a toy. Close
attention is necessary when used by or near
children, pets or plants.
• Use only as described in this manual. Use
only manufacturer’s recommended
accessories.
• Do not pull cord, use cord as a handle,
close a door on cord, or pull cord around
sharp edges or corners. Keep cord away
from heated surfaces.
• Use only extension cords UL-rated or cUL at
15 amperes. extension cords rated for less
amperage may overheat. Care should be
taken to arrange the cord so that the cord
cannot be pulled or tripped over.
• Turn off all controls as applicable before
unplugging from electrical outlet.
• Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum with wet
hands or operate without shoes.
• Do not put any objects into openings. Do
not use with any opening blocked. Keep free
of dust, lint, hair and anything else that may
reduce air flow.
• Store your appliance indoors in a cool, dry
area.
• Keep your work area well lit.
• Do not immerse the vacuum into water
or other liquids.
• Keep end of hose, wands and other
openings away from your face and body.
• Use only on dry surfaces.
• Using improper voltage may result in
damage to the motor and possible injury to
the user. Correct voltage is listed on rating
label.
SAVE THESE INSTRUCTIONS
For Household Use Only
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
1
Rev. 08/02C
Model EP722
ONE (1) YEAR LIMITED WARRANTY
Euro-Pro Operating LLC warrants this product to be free from defects in material and workmanship
for a period of one (1) year from the date of the original purchase, when utilized for normal household
use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, return the complete appliance and accessories, freight prepaid to Euro-Pro
Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901. If the appliance is found by
EURO-PRO to be defective in material or workmanship, EURO-PRO will repair or replace it free of
charge. Proof of purchase date and $ 9.95 to cover the cost of return shipping and handling must be
included. *
Non-durable parts including, without limitation, dust bags, filters, brushes and electrical parts which
normally require replacement are specifically excluded from warranty.
The liability of Euro-Pro Operating LLC is limited solely to the cost of the repair or replacement of
the unit at our option. This warranty does not cover normal wear of parts and does not apply to any
unit that has been tampered with or used for commercial purposes. This limited warranty does not
cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or
mishandling in transit. This warranty does not cover damage or defects caused by or resulting from
damages from shipping or repairs, service or alterations to the product or any of its parts, which have
been performed by a repair person not authorized by EURO-PRO.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of Euro-Pro Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
Euro-Pro Operating LLC liable for incidental or consequential damages of any nature whatsoever.
Some states do not permit the exclusion or limitation of incidental or consequential damages, so the
above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe is
the problem with item. We recommend you insure the package (as damage in shipping is not
covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”.
We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The registration
will enable us to contact you in the unlikely event of a product safety notification. By returning this
card you acknowledge to have read and understood the instructions for use, and warnings set forth in
the accompanying instructions.
RETURN TO Euro-Pro Operating LLC: 94 Main Mill Street, Door 16, Plattsburgh, NY 12919
Model EP722
________________________________________________________________________
Appliance model
________________________________________________________________________________
Date purchased
Name of store
________________________________________________________________________________
Owner’s name
________________________________________________________________________________
Address
City
State
Zip code
Printed in China
FOR REPLACEMENT FILTER INFORMATION
GETTING TO KNOW YOUR VACUUM
for Model EP722
Call:
1-866-98SHARK (1-866-987-4275)
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
or
visit our website: www.sharkvac.com
Replacement HEPA filter SKU# XSH722
FOR TECHNICAL SUPPORT
for Model EP722
In U.S.: 1 (866) 805-6850
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The HEPA Dust Cup Filter may be washed. We recommend that this be done once a
month or when suction appears reduced .
To wash your HEPA Dust Cup Filter, hold filter cartridge by frame flange, flange side
up and rinse under water. When finished, shake off excess water. Do NOT wash in
dishwasher.
It is important that when you wash the HEPA dust cup filter, you allow it to air dry
COMPLETELY before using again. We recommend 24 hours to air dry. DO NOT DRY
IN DRYER.
IMPORTANT: Both the Pre-Motor and the Micro Exhaust filters should be replaced
every 6 months or sooner if required.
All filters should be checked regularly for signs of damage, preferable after each
cleaning task. The filters must be replaced immediately if they become damaged.
Always disconnect the vacuum from the electrical outlet when checking the filters.
Important:
This vacuum cleaner is equipped with a motor protective thermostat. If for some
reason your vacuum overheats, the thermostat will automatically turn the unit off.
Should this occur, unplug the vacuum from the wall outlet and turn off the switch.
Empty the dust cup, "TapClean" the dust cup filter and check for blockages in hose
and suction inlet. Allow the unit to cool for a minimum of 45 minimum prior to restarting
the unit. To restart, re-plug the vacuum into the wall socket and turn the switch back
on.
9
1.
2.
3.
4.
5.
6.
7.
8.
Hose
Cord Rewind Button
Power On/off Button
Handle
Dust Cup
Air Intake Duct
Air Driven Turbo Brush
Dust Cup Handle
9. Telescopic Tube
10.Floor to Carpet Brush
11.Hand Held Air Driven Turbo Brush
12.Upholstery Brush
13.Dusting Brush
14.Crevice Tool
15.Shoulder Strap
Technical Specifications
Voltage:
Power:
120V., 60Hz.
10.8 Amps, 1300 Watts
2
PRECAUTIONARY MEASURES
Important: If the suction opening of the unit, the hose or the chrome telescopic tube
are BLOCKED, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
1.
4.
Do not operate the vacuum
cleaner too close to heaters or
radiators.
When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
OPERATING INSTRUCTIONS
Motor Thermostat
Important: This vacuum cleaner is
equipped with a motor protective
thermostat. If for some reason your
vacuum overheats, the thermostat will
automatically turn the unit off. Should this
occur, unplug the vacuum from the wall
outlet and turn off the switch. Empty the
dust cup, "TapClean" the dust cup filter
and check for blockages in hose and
suction inlet. Allow the unit to cool for a
minimum of 45 minimum prior to
restarting the unit. To restart, re-plug the
vacuum into the wall socket and turn the
switch back on.
Flat & Upright Parking Position
Please note that your vacuum cleaner
can be conveniently placed in a space
saving vertical parking position or in a
convenient flat parking position.
1. Place unit on its side. Slide floor
nozzle into locking position with
receptacle which rests on top of unit.
2. While laying flat on 3 wheels, slide
floor nozzle into locking position
with receptacle which rests on the
rear side of the unit.
Attaching the Shoulder Strap
5.
2.
Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
6.
Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
Do not use without all filters in place.
Note: This vacuum cleaner is equipped
3.
with a plug and power cord that retract
automatically. If the cord or plug get
damaged, it must be replaced by a
qualified technician.
Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the dust bag.
Use the hooks to attach the shoulder
strap to the vacuum cleaner.
First pass the flexible hose through
the loop of the shoulder strap and
then attach the two hooks to the
strap hookup holes at the bottom of
the vacuum cleaner as shown in
illustration below.
Warning: Hold the plug when
rewinding the cord. Do not allow the
cord to whip when rewinding.
3
8
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Changing the Pre-Motor Filter
9. Reassemble the debris screen to the
HEPA filter cartridge and replace into
dust cup (container). Ensure that the
filter assembly is completely seated
inside the dust cup (container).
• Filter should be cleaned at least twice
a year or when it becomes visibly solid.
• Always operate the cleaner with the
filter installed.
• Disconnect from electrical outlet before
cleaning the filter.
1. Lift dust cup handle to remove
dust cup.
2. Remove the filter from the filter
grill.
Assembling Your Vacuum Cleaner
Note: Always remove the power plug
4. Fitting the Floor to Carpet
Brush or the Air Driven Turbo
Brush to the Telescopic Tube
from the wall outlet before assembling or
removing accessories.
Push the telescopic tube into the
desired floor brush as show in the
illustration below.
1. Attaching the Flexible Hose
into the Vacuum
Connect the flexible hose into the air
intake duct. Push in until you hear a
“click”, indicating it is in its locked
position.
Telescopic
Tube
To remove the flexible hose reverse
10. Attach the dust cup (container) to the
vacuum.
the operation.
Floor to Carpet
Nozzle
5. Air Driven Turbo Brush
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
Fig. A
is properly
Wash once
"TapCleaned”
a month or
after each use
when
and suction
suction
appears
does not return
reduced
to 100%, then
we suggest that
Warning: Allow 24
the HEPA filter
hours for drying before
be “TapCleaned”
replacing in unit.
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) This should be
done once a month or when
suction appears to be reduced.
3. Replace with a new filter and reinstall
in vacuum.
Changing the Micro-Exhaust
Filter
Air Intake Duct
2. Fitting the Telescopic Tube
to the Curved Wand / Hose
Extension
•
•
Push the telescopic tube into the
curved wand / hose extension, as
shown in the illustration below.
1. Remove the exhaust filter grill by
pulling the locking tabs towards
you.
2. Remove the used micro-exhaust
filter.
3. Insert a new micro-exhaust filter
and replace the filter grill.
IMPORTANT: Both the Pre-Motor and
the Micro Exhaust filters should be
replaced every 6 months or sooner if
required.
IMPORTANT: All filters should be
checked regularly for signs of
damage, preferable after each
cleaning task. The filters must be
replaced immediately if they become
damaged.
Always disconnect the vacuum from
the electrical outlet when checking the
filters.
CAUTION: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
Important: Do NOT use the HEPA filter
cartridge without the debris screen in
place.
7
•
•
The efficiency of your Air Driven
Turbo Brush depends on the bristle
brush rotating at high speed. Strong
air suction is needed to accomplish
this. In order to endure that
maximum air suction is maintained,
please read the following instructions:
Empty the Dust Cup frequently during
use.
Always “TapClean” the HEPA dust
cup filter and debris screen each time
the dust cup is emptied.
Ensure that the rotating bristle brush
is kept free of hair and string.
Inspect the turbine regularly to ensure
that the air passage is free of dirt and
debris.
Hand Held Air Driven
Turbo Brush
3. Extending the Chrome
Telescopic Tube
Push forward on the plastic button
and pull the inner chrome tube
outward.
Air Driven Turbo
Brush
Plastic
Knob
4
OPERATING INSTRUCTIONS
Crevice Tool, Upholstery and
Dusting Brush
1.
2.
3.
OPERATING INSTRUCTIONS
3. To rewind the power cord,
press the cable rewind button
with one hand and guide the
power cord with the other hand to
ensure that it does not whip
causing damage.
Crevice Tool
For radiators, crevices,
corners, baseboards and
between cushions.
Dusting Brush
The dusting brush is used for
the furniture, venetian blinds,
books, lamp shades and
shelves.
Upholstery Brush
The dusting brush is used
for the furniture.
Cord Rewind
Yellow
Red Symbol
Symbol
Warning: Hold the plug when rewinding
the cord. Do not allow the cord to whip
when rewinding.
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
Note: Before using the appliance,
unwind a sufficient length of cable and
Insert the plug into the wall socket. A
yellow mark on the power cord shows the
ideal cable length. Don’t pull the power
cord beyond the red mark.
Cleaning Air Driven Turbo Brush
Locking Latch
Tilt
Upwards
Turbine
Power Cord
Your vacuum cleaner includes a power
cord, which is automatically retractable.
To extend your power cord, pull from
rear and extend to desired length.
When cleaning is finished, first switch
off power and disconnect plug from
electrical outlet. Then press on cord
rewind button. If the cord does not fully
retract, pull it out again and then press
on cord rewind button.
1. Slide locking latch forward then tilt the
top housing of the brush upwards. The
top housing is hinged and will tilt up
approximately 45° only.
2. Inspect turbine wheel and air passage
for debris and/or blockage. Remove
debris if present.
3. Inspect the rotating brush for built-up
hair or string. If present, remove by
carefully cutting with scissors. Avoid
damaging or cutting bristles.
4. Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.
1. Insert the power plug into the wall
outlet.
2. Press the Power On/Off Switch to
activate the vacuum cleaner.
Cleaning & Changing the
HEPA Dust Cup Filter
4. Take the HEPA dust cup filter
out of the dust cup, do not let
dust fall out of dust cup.
Warning: Always unplug the unit from
electrical outlet before opening the Dust
Cup (container).
Important: Do NOT use the HEPA filter
cartridge without the debris screen in
place.
Warning: After each Use - Always
remove the Filter Debris Screen from the
HEPA Dust Cup Filter, then vigorously
“TapClean” HEPA Filter until no more
dust can be removed.
IMPORTANT, Please Note : The
“TapClean” HEPA Dust Cup Filter &
Debris Screen will stop most of the tiniest
dust particles and airborne allergens from
re-entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust Cup
Filter will quickly accumulate, inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. This can
cause the motor to overheat and the resettable thermostat to trip. (Should this
happen turn off the switch, unplug the unit
and allow unit to cool down. Clean the
HEPA Filter and Debris Screen as
described in this section, then reconnect
unit and proceed with vacuuming.)
5. Take the dust cup and dispose
of the dust inside.
6. Separate the debris screen from the
HEPA filter cartridge by grasping the
debris screen with one hand and the
filter frame with the other and pull
apart.
HEPA Filter
Debris Screen
7. Vigorously “TapClean”
the HEPA Dust
Cup Filter on a
hard surface until no
more dust is observed
falling out from
between the pleats of
the filter. Please note
that on the under side of the HEPA
dust cup filter there is a small brush
which you can use to brush out the
pleats of the filter.
1. Push the Power On/Off switch
to the OFF position to
disconnect the power.
2. Remove the flexible hose.
3. Remove the dust cup by lifting
the dust cup handle. See
illustration below.
Dust Cup Handle
Power On/Off Button
8. “TapClean” the Debris
Screen or rinse under
a faucet until clean.
Remember that
the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
5
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising