- Home
- Domestic appliances
- Large home appliances
- High-pressure cleaners
- Euro-Pro
- VPW49HA
- Owner's manual
Euro-Pro VPW43 Owner's Manual
Add to my manuals6 Pages
Euro-Pro VPW43 is a powerful electric pressure washer, suitable for a variety of cleaning tasks around your home. With a maximum pressure of 12.5 amps, it can effortlessly remove dirt, grime, and stains from surfaces like patios, decks, cars, and siding. The VPW43 features a detergent tank, allowing you to easily apply cleaning solutions to surfaces before rinsing them off. It also comes with a variety of nozzles for different cleaning needs, including a turbo nozzle for stubborn stains and a soap nozzle for applying detergent.
advertisement
OWNER'S MANUAL
Model VPW43
120V., 60 Hz., 12.5 Amps.
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: 1-800-798-7398
SAFETY & WARNING INSTRUCTIONS
For safety reasons, it is recommended that you read this manual before attempting to operate this appliance. Failure to follow these instructions can result in personal injury or equipment problems. To help recognize note the following symbols:
DANGER
Danger indicates an imminently hazardous situation, which, if not avoided, WILL result in death or serious injury.
10. Do not overreach or stand on unstable support. Keep good footing and balance at all times.
11. Follow maintenance instructions
12. This product shall be connected to a power supply receptacle protected by a
WARNING
Warning indicates a potentially hazardous situation, which, if not avoided, COULD result in death or serious injury.
(electric power washers only).
13. If product is provided with a GFCI, be sure to inspect the cord and GFCI prior to use. Any repair or replacement of the qualified (licensed or certified) electrical technician.
CAUTION
Caution indicates a potentially hazardous situation, which, if not avoided, MAY result in death or serious injury.
NOTE: Information that requires special attention.
Important Safety Instructions SAVE THESE
INSTRUCITONS
When using this product, basic precautions should always be followed, including the following:
DANGER
1. Read all instructions before using the product.
2. To reduce the risk of injury, close supervision is necessary when this product is used near children.
3. Always disconnect power (electric units) before disassembling, repairing or changing attachments on the unit.
4. Follow all safety codes as well as the
Occupational Safety and Health Act
(OSHA).
5. Ensure safety devices are operating properly before each use. DO NOT remove or modify any part of the gun or unit.
6. Know how to stop this unit and relieve pressure quickly. Be thoroughly familiar with the controls.
7. Stay alert - Watch what you are doing.
8. Do not operate this unit when fatigued or under the influence of alcohol or drugs.
Rev. 11/03
WARNING
Risk of injection or severe injury. Keep clear of nozzle. Do not discharge streams at persons. This product is to be used only by trained operators. Always remove lance
• Keep clear of nozzle. NEVER direct high
• Always wear safety goggles or glasses and protective clothing when operating, performing maintenance or changing accessories.
• Never put hands or fingers over the spray
• Never try to stop or deflect leaks with any
• Always engage the trigger safety latch in the safe position when spraying is stopped even if only for a few minutes.
• Always follow detergent manufacturer's detergents. Always protect eyes, skin and respiratory system from detergent use.
WARNING
SERVICING OF A DOUBLE-INSULATED
APPLIANCE.
In a double-insulated product, two systems of insulation are provided instead of provided for a double-insulated product, nor should grounding means be added to the product requires extreme care and knowledge of the system and should be done only by qualified service personnel.
Replacement parts for a double-insulated original parts. A double-insulated product is marked with the words
" double Insulation" or "Double
Insulated". Product may also be marked with symbol shown.
1
Model VPW43
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to EURO-PRO
Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901. If the appliance is found by
EURO-PRO Operating LLC to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $ 18.95 to cover the cost of return shipping and handling must be included. *
Non-durable parts including, without limitation, hoses, lances, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever.
Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you .
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
*Important:
Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
------------------------------------------------------------------------------------------------------
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase in order to validate the foregoing Limited Warranty. The registration will enable us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
________________________________________________________________________
Appliance model
________________________________________________________________________________
Date purchased Name of store
________________________________________________________________________________
Owner’s name
________________________________________________________________________________
Address City State Zip Code
Printed in Italy
10
PROBLEM
PRESSURE
WASHER WILL
NOT START WHEN
THE ON/OFF
SWITCH IS IN THE
"ON" POSITION
TROUBLE SHOOTING
POSSIBLE REASON
1. Electrical socket is faulty or breaker has tripped.
2. Voltage inadequate.
has
4. Power cord is not plugged in.
POSSIBLE SOLUTION plug, breaker.
2. Check that the voltage is adequate.
3. Reset/Try another electrical outlet.
4. Plug in power cord.
PUMP DOESN'T
REACH
ADEQUATE
PRESSURE OR
CAVITATES
1. Water intake filter is clogged.
2. Pump is drawing air.
3. Diameter of garden hose is too small.
4. Water supply is restricted.
1. Remove and clean water intake filter.
2. Tighten system.
3. Replace with 3/4 inch garden hose.
4. Check hose for kinks or leaks, open tap fully.
PRESSURE
WASHER HAS OR
WILL NOT
MAINTAIN
PRESSURE
1. Excessive air in waterline and pump.
2. Water supply is restricted.
1. Turn unit and water supply off/Bleed system/Hold trigger down. Allow water to flow through the pump for
30 seconds.
2. Check hose for kinks or leaks, open tap fully.
PRESSURE
WASHER MAKES
EXCESSIVE NOISE
1. Air intake is blocked.
2. Water intake filter is dirty.
1. Clean the air intake vents.
2. Check & clean filter.
MOTOR DOES
NOT RUN
CONTINUOUSLY
WHEN TRIGGER IS
SQUEEZED/
MOTOR BUZZES
WHEN TURNED
ON BUT DOES
NOT
START/MOTOR
STOPS RUNNING
WHILE UNIT IS IN
USE
1. Net voltage is lower than suggested.
1. Check that the voltage is adequate.
9
WARNING
Do not use pressure that exceeds the operating pressure of any of the parts system. Ensure that all equipment and maximum working pressure of the unit.
WARNING
Explosion hazard.
• NEVER spray flammable liquids of use combustible dust, liquids or vapors.
• NEVER operate this machine in a closed building or in or near an explosive environment.
WARNING
Do not spray electrical apparatus or wiring.
• NEVER disconnect the high pressure the system is pressurized. To depressurize the machine, turn the power and water supply off, then press the gun trigger 2-3 times.
• NEVER permanently engage the trigger
• NEVER operate the machine without all the unit (handle, gun/lance assembly, nozzle, etc.).
WARNING
Equipment damage.
• ALWAYS turn water supply "ON" before
Running pump dry causes serious damage.
• Do not operate the pressure washer with the inlet water screen removed. Keep
• screen clear of debris and sediment.
equipment regularly and repair or replace worn or damaged parts immediately.
machine.
• Never leave the lance unattended while
• Never attempt to alter factory settings.
Altering factory settings could damage the unit and will void the warranty.
starting and operating the machine.
• NEVER allow the unit to run with the minute. Resulting heat buildup will damage pump.
• NEVER store the pressure washer outdoors
• Release trigger when changing from high to low pressure modes. Failure to do so could
• This unit must always be used in the horizontal position.
CAUTION
hose may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose.
EXTENSION CORDS
DANGER three wire extension cords that are in good condition. Use only extension cords that are cords are identified by a marking "Acceptable for use with outdoor appliances; store indoors having an electrical rating not less than the product. Do not use damages extension cords. Examine extension cord before using and replace if damaged. Do not abuse disconnect. Keep cord away from heat and sharp edges. Always disconnect from the from the extension cord.
cords on this product.
DANGER
Failure to follow these instructions can result in serious injury, including death.
WARNING
To reduce the risk of electrocution, keep all touch the plug with wet hands.
Extension Cord
Allowable Length
25' 50’
14 AWG YES NO
12 AWG YES YES
2
GETTING TO KNOW YOUR PRESSURE WASHER
8
15 16
13
14
11
10
9
12 7
1. Pressure Washer
2. Water Intake
3. High Pressure Output
4. On/Off Switch
5. Trolley
6. Trolley Handle
7. High Pressure Hose
8. Rotary Brush
9. Trigger Gun
10. Safety Lock
11. Trigger
12. High Pressure Hose Connector
13. High Pressure Lance
14. Fan Jet Lance
15. Detergent Applicator Bottle
16. Garden Hose Coupling
17. Handle Bracket
18. Top Brace
19. Legs (x2)
20. Support Bracket
21. Front Support
22. #8 Phillips Screws 1/2–inch (x4) (not shown)
23. #8 Phillips Screws 1-inch (x4) (not shown)
Illustrations may differ from actual product.
Technical Specifications
Voltage:
Power:
Pressure:
Flow Rate:
120V., 60Hz.
12.5 Amps.
1450 psi. (max)
1.45 GpH
3
OPERATING INSTRUCTIONS
Motor Thermostat
Important:
This pressure washer is equipped with a motor thermostat. The motor will stop if it is overheating. Wait
10-20 minutes before starting the unit again. If it stops again, please call EURO-
PRO Operating LLC customer service at
1-800-798-7398.
Ground Fault Circuit
Interrupter (GFCI)
This unit is equipped with a Ground
Fault Circuit Interrupter (GFCI) built into the plug. This device provides additional protection from the risk of electrical shock. When connecting the GFCI to the electrical outlet, the indicator should appear red. If the indicator is not red, depress the RESET button on the GFCI until the indicator appears red.
Cleaning Tips
Wood Decks: Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent applicator bottle and apply to the area being cleaned. For optimal results, reduce your work area to small sections and clean each section one at a time.
Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure. Do not let the detergent dry on the deck. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan jet keeping the tip of the spray nozzle 8-12 inches from the surface. Caution: For soft woods, increase the distance from the cleaning surface.
Cars, Boats, & Motorcycles: Wet down area to be cleaned before applying detergent with clean water. Fill the detergent applicator bottle and apply to the area being cleaned. To achieve best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes but do not let it dry. Rinse at high pressure using the fan jet in a sweeping motion keeping the tip of the spray nozzle at least 8-10 inches away from the surface. Maintain a further distance when using a direct spray. Wipe surface for a polished finish.
8
OPERATING INSTRUCTIONS
Using the High Pressure Lance
The high pressure lance may be used alone or with the detergent applicator bottle.
Add detergent to the bottle and then attach the detergent applicator bottle to the high pressure lance, just push it on the end of the high pressure lance.
(Fig. 11 & 12) To remove the detergent applicator bottle, lift the tab on the top of the connector and pull off.
Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit
"Off". Unplug from electric outlet and disconnect the water supply. Remove the lances, trigger gun and hose from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 15)
Fig. 11
Fig. 12
Using the Brush With the Trigger
Gun
The brush is used with the trigger gun.
Push the brush onto the trigger gun nozzle and turn clockwise to lock as you would for the lances. (Fig. 13) The brush may be used for washing cars, boats, windows and other similar items.
The brush operate at open orifice pressure so that they will not direct a stream of water.
Fig. 13
Maintenance & Cleaning
Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed.
Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 14).
Remove periodically and inspect for any deposits that might accumulate there.
Fig. 14
Hose Connector
Water Intake
Fig. 15
This will occur more frequently if your water supply is very hard.
Storing Your Pressure Washer
When you have finished using your pressure washer, follow these steps for safe storage:
1. Turn the pressure washer to the
"Off" position.
2. Turn off the water supply.
3. Before disconnecting the high pressure hose connection, point the trigger gun in a safe direction away from you and discharge the high pressure water. Disconnect the high pressure hose from the pressure washer and trigger gun.
4. Disconnect garden hose from pressure washer.
5. Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings.
6. Drain detergent applicator bottle and flush with clean water.
7. Wipe away any remaining water on all parts and fittings.
8. Engage the trigger gun safety lock.
9. Store the unit and accessories in a room above 32°F.
Winterizing & Long Term Storage
1. Disconnect all water connections.
2. Turn the pressure washer on for a few seconds, until any remaining water in the pump exits.
3. Turn the unit off immediately.
4. Store the pressure washer, parts and accessories in an area with a temperature above 32°F.
7
Suitable Use of Your Pressure
Washer
This high pressure washer is suitable for non-professional use. The working temperature must range between 40°F and 120 °F. The machine is supplied with a trigger gun, equipped with a trigger handle to offer a comfortable working position.
The high pressure washer is suitable for washing with cold water only. The water that you use for the pressure washer must not be dirty, sandy or contain any corrosive chemical products.
The pressure washer may be used to wash shutters, doors, tiles, cars, decks, campers, etc., where high water pressure is necessary to remove dirt.
With the detergent applicator bottle, the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned .
When using the pressure washer we recommend the use of personal safety items to reduce the risk of accidental injury.
Correct Use of the Pressure
Washer
• Place the pressure washer in a safe area and on a horizontal surface.
• When using the pressure washer, hold the trigger gun firmly with one hand on the handle and the other on the lance. (Fig. 1)
Fig. 1
• NEVER point the water jet at electric person or animal.
Assembling the Pressure Washer
Trolley
1. Carefully take all the trolley parts and place together on a flat, stable surface.
2. Insert the two (2) legs into the support brackets on the unit and secure with two (2) of the 1/2-inch #8
Phillips screws provided. (Fig. 2)
Unpacking Your Pressure Washer
After you open the package, check to make sure that all the parts are in the box as pre parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual.
If you have any questions, call EURO-
PRO Operating LLC customer service at
1 (800) 798-7398. Keep all small and potentially harmful parts of the package
(plastic bags, foamed polystyrene, nails, etc.) out of the reach of children.
Fig. 2
3. Insert the handle into the handle bracket and secure with two (2) of the
1-inch #8 Phillips screws provided.
(Fig. 3)
Fig. 3
4
Assembling the Pressure Washer
Trolley (cont)
4. Slide the top brace over the legs and insert the handle assembly onto the top of the legs. Secure the handle assembly to the legs with two (2) of the 1/2-inch #8 Phillips screws provided. (Fig. 4)
Attaching High Pressure Hose to
Pressure Washer
Once the pressure washer is assembled to the trolley, you are ready to use the unit.
1. While facing the front side of the unit attach the high pressure hose to the high pressure output connector on the right side of the unit. Twist on tight to avoid leakage. (Fig. 7)
Fig. 7
Fig. 4
5. Slide the top brace down the legs until it reaches the top of the pressure washer. Secure the top brace to the pressure washer unit with two (2) of the 1-inch #8 Phillips screws provided. (Fig. 5)
6. When the unit is finally assembled, it should look like the illustration at the right. (Fig. 6)
Fig. 5
High pressure output fitting
2. Once the high pressure hose is connected to the main unit, you can attach any of the lances and accessories that you desire. To attach either of the lances or brush to the trigger gun, hold the trigger gun in your left hand insert the desired lance or brush and push it in all the way into the connector on the trigger gun and turn it clockwise 60° until it locks in place. To remove the attachment, push down on the attachment and turn counterclockwise 60° and then pull out.
Make sure that the attachments are securely locked in place before use.
(Fig. 8)
Fig. 8
Fig. 6
5
Garden Hose Connection
Once all the desired attachments and the high pressure hose are attached to the pressure washer, you can connect the garden hose to the unit.
1. Attach the male adapter (supplied) to the water intake connector on the left hand side of the unit. (Fig. 9)
2. Attach the female hose coupling to the garden hose. (Fig. 9)
3. Connect the female hose coupling to the male adapter making sure that it is tightly secured in place. (Fig. 9)
CAUTION
When you wish to stop using the pressure washer temporarily, make sure that the safety lock has been engaged to avoid any accidental operation. (Fig. 10)
Safety
Lock
Fig. 9
Low pressure water inlet
4. After all the connections have been and BEFORE you plug the pressure washer into an electrical outlet, open the water supply and press on the trigger switch in order to remove any air which may be in the hose or pump. Continue to press on the trigger switch until you get a constant flow of water coming out of the trigger gun. Allow water to flow for 30 seconds.
5. Once this is accomplished, stop pressing the trigger switch. Engage the safety lock on the trigger
6. Ensure that the "On/Off" switch, at the rear of the unit, is on the "Off" position, then plug the unit into an electrical outlet and turn the unit to the "On" position.
7. Now you are ready to use the pressure washer. Disengage the safety lock and depress the trigger on the trigger gun.
Fig. 10
Using the Fan Jet Lance
When using the pressure washer with the fan jet lance to clean wood decks, siding vehicles, etc., always start using the fan spray and begin spraying from a minimum 36" away to avoid damaging the surface of the material that you are cleaning. Always clear the area that you will be cleaning of people, pets and objects.
6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project