Extron electronic 200C User's Manual

Add to my manuals
30 Pages

advertisement

Extron electronic 200C User's Manual | Manualzz
User’s Manual
HSA 200S & HSA 200SE
HSA 200C & HSA 200CE
HSA 222S & HSA 222C
Hideaway® Surface Access Products
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-695-01 Rev. I
06 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
ᅝܼ乏ⶹsЁ᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟‫ݠ‬Ё
᳝䞡㽕ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇‫ݙ‬᳝ᲈ
䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢкs䑩ㅸỀ䑩嬦嫿⡈↎⼆枼敆嬼⶷䍇夤ㆁ
㙊⫊₩⏍Ề䑩嬵㕏ɿ
ֱᄬ䇈ᯢкs䑩ㅸⷕ἞⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề
䑩ɿ
䙉ᅜ䄺ਞs䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊
₩⏍㐎ẝ嬵㕏ɿ
䙓‫ܡ‬䗑ࡴsᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅⴦₸ㅗ
弾⇡嫿⡈澤Ḧ忀₎⊲斪ɿ
䄺ਞ
⬉⑤s嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈⼆枼Ề䑩
㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ䩭ᵊ㚢一澠♱一澡㕰⫊₩嫿
㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ
ᢨᥝ⬉⑤sᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿⡈⍏
ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅䑶㷑一ɿ
⬉⑤㒓ֱᡸs⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ
㓈ᡸsㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ嫿⡈⃆怩㯢
㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪ᵎ壂儫ⴲ
嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ
䗮亢ᄨs㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦敳㪣
㙻⃆㒐だ₄ḷ弈䀮ɿᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛栏⪕ɿ
䫖⬉∴sᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩ᵏ
⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ㉊䂨䑠ᷨ⋃䗅⸻
嫯⡅䍇ⷠ⹄䑶㮡ɿ
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. The Class A limits are
designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter 1 • Introduction .......................................................... 1-1
About the Hideaway Surface Access Products ....... 1-2
About the Extender board line driver .................................. 1-4
Features ...................................................................................... 1-5
All models .............................................................................. 1-5
HSA 200CE and HSA 200SE models only .............................. 1-5
Chapter 2 • Installation ............................................................. 2-1
Installation Overview .......................................................... 2-2
Preparing the Routing Template ................................... 2-3
Preparing the Table and Mounting the Enclosure ... 2-4
Preparing the table with a router ........................................ 2-4
Preparing the table with a hole saw
(HSA 200C, HSA 200CE, or HSA 222C—US version only) ..... 2-6
Installing the HSA enclosure (all) .......................................... 2-6
Underside Features and Cabling Connections ....... 2-8
All HSA 200 models only ....................................................... 2-9
HSA 200C and HSA 200S (no Extender board) only ............ 2-9
All HSA 200 and HSA 222 models ....................................... 2-10
HSA 200CE and HSA 200SE (Extender board) only ............ 2-11
Power connector wiring .................................................. 2-12
Front Panel Connectors .................................................... 2-12
Pre-installation Testing and Troubleshooting
(HSA 200CE and HSA 200 SE models only) ............. 2-16
If the image does not appear or there is no sound .......... 2-16
If the image is not displayed correctly ............................... 2-16
Chapter 3 • Maintenance and Modifications ............ 3-1
Removing and Replacing the Enclosure .................... 3-2
Replacing the Bezels ............................................................ 3-3
Replacing the Gas Lift ......................................................... 3-8
Adjusting the Top Panel ................................................... 3-13
HSA 200/222 Series • Table of Contents
iiii
Table of Contents, cont’d
Appendix A • Reference Information ............................ A-1
Specifications ......................................................................... A-2
HSA Part Numbers ................................................................ A-7
Included Parts ......................................................................... A-8
Routing Templates ............................................................... A-8
Accessories ............................................................................... A-8
Top Plate Dimensions ......................................................... A-8
Appendix B • Packaging for Shipment .......................... B-1
All trademarks mentioned in this manual are the properties of their respective owners.
68-695-01 Rev. I
06 09
HSA 200/222 Series Surface Access Products
1
Chapter One
Introduction
About the Hideaway Surface Access Products
Features
iv
ii
HSA 200/222 Series • Table of Contents
Introduction
About the Hideaway Surface Access Products
The Extron Hideaway HSA 200 series and HSA 222 series are
furniture-mounted, architectural solutions for inconspicuous
computer video and/or network access and control.
The HSA 200C (figure 1-1) and HSA 200S (figure 1-2) provide:
•
One standard grounded AC receptacle

The US versions have US power receptacles
Figure 1-2 — HSA 200S hideaway enclosure

The international versions have several different
types of power receptacles available, including
Universal, UK, French, Israeli, Australian, Indian,
European, and Swiss receptacles.
The HSA 222S (figure 1-3) and HSA 222C (US model only)
provide:
The Universal AC outlet is fully compatible with
Europlug, British, Indian, Danish, and Italian plug
types. See the universal AC outlet guide on the Extron
Web site, www.extron.com, for compatibility details on
all plug types.
•
Two RJ-45 Category (CAT) 6 connectors (teminated in
accordance with the TIA/EIA 568 A standard)
•
One 15-pin female HD computer video connector
•
One 3.5 mm stereo female jack.
•
•
Two standard grounded AC receptacles

The US versions have US power receptacles

The international version has several different types
of power receptacles available, including UK, French,
Israeli, Australian, Indian, European, and Swiss
receptacles.
Two RJ-45 CAT 6 connectors
Figure 1-3 — HSA 222S hideaway enclosure
The International HSA 222 is only available with a
square top plate.
Figure 1-1 — HSA 200C hideaway enclosure
The HSA 200CE and HSA 200SE provide all of the HSA 200C
or HSA 200S features plus:
•
1-2
For all models, cabling inside the enclosure runs the AC power
line and RJ-45 signal lines from the HSA panel connectors to
connectors on the bottom of the enclosure. For the HSA 200
model, the computer video signal is routed to 5 BNC connectors
on pigtails. On HSA 200S and HSA 200C units, the audio signal
is sent to a 3-pole, 3.5 mm captive screw connector on a pigtail.
On HSA 200SE and HSA 200CE units, the audio signal is sent to
a 5-pole, 3.5 mm captive screw connector on the back of the unit.
An Extender board, which sends the input signal a
greater distance and converts the audio input to a
balanced signal. See “About the Extender board line
driver”, on page 1-4, for more details.
HSA 200/222 Series • Introduction
HSA 200/222 Series • Introduction
1-3
Introduction
The installed enclosures fit nearly flush within a table or podium
top (figure 1-4), storing the connectors out of the way and out of
sight. To access the connectors, the user presses down on the
top of the enclosure, releasing a mechanical latch. A gas lift tips
the connectors into view.
Projector
Extron HSA 200C
Extron
HSA 200C
Features
All models
•
UL/c-UL listing
•
CSA certification
•
Easy access to connectors
•
Durable mechanical movement and latching mechanism
•
Available in a variety of surface finishes
•
Includes a variety of RJ-45 connector bezel colors: black,
red, blue, orange, gray, white, ivory, yellow, and green
•
Compact size
•
Computer video and audio connections (HSA 200 models
only)
•
RJ-45 (CAT 6) network, data, or communications
connections (teminated in accordance with the
TIA/EIA T 568 A standard)
•
Grounded AC receptacle(s)
Hideaway Surface
Access Enclosure
HSA 200CE and HSA 200SE models only
Mounted
Through a Table
or Podium
Figure 1-4 — HSA 200C application
HSA 200CE and 200SE models include an Extender line driver
board, which provides several features not available on the
standard models.
•
Signal boosting ability — The gain/peaking adjustment
increases video signal voltages to compensate for signal
degradation caused by long cables. The Extender board
can send a high resolution signal up to 250 feet (76.2 m)
through Extron’s BNC-5 Mini HR cable.
•
Sync restoration — Each Extender board restores low
level sync voltages found on many laptops (as low as two
volts) to normal TTL levels.
•
Stereo audio — Unbalanced stereo audio inputs can be
output as balanced or unbalanced stereo audio.
About the Extender board line driver
The Extron Extender board in the HSA 200CE and 200SE is a
one-input VGA – UXGA/VESA line driver with audio. It boosts
the video signal between a laptop or desktop computer and a
monitor or projector. It has a 300 MHz (-3 dB) video bandwidth.
The Extender accepts one computer-video input and one stereo
audio input, and features one buffered VGA-type RGB output
and one stereo audio output. With an optional Mac/VGA
adapter, the Extender board can also buffer Macintosh signals.
1-4
HSA 200/222 Series • Introduction
HSA 200/222 Series • Introduction
1-5
Introduction
HSA 200/222 Series Surface Access Products
2
Chapter Two
Installation
Installation Overview
Preparing the Routing Template
Preparing the Table and Mounting the Enclosure
Underside Features and Cabling Connections
Front Panel Connectors
Pre-installation Testing and Troubleshooting
(HSA 200CE and HSA 200SE Models Only)
1-6
HSA 200/222 Series • Introduction
Installation
Installation Overview
Preparing the Routing Template
Install and set up the HSA surface access enclosures as follows:
1
If you have an unprepared mounting template, prepare
the template. See “Preparing the Routing Template” on
the next page.
2
If desired, install the optional RJ-45 to RJ-11 conversion
kit(s) to replace one or more RJ-45 connectors with RJ-11
connectors. Refer to the appropriate RJ-45 to RJ-11
Conversion Kit manual, for either the HSA 200 models or
the HSA 222 models.
3
4
Extron offers a metal template for each HSA model.
Appendix A lists the HSA 200 and HSA 222 template part
numbers. Extron recommends using this template as a guide to
cut the hole in the table where the HSA will be installed.
The metal routing template is reusable. Do not discard
this template when the installation is complete. Save it
for installing future HSA enclosures of the same size.
1.
If desired, install the optional flexible conduit kit to
replace the removable AC power cord. Refer to the
Flexible Conduit Kit manual.
Cut 1/2" x 4" strips of soft, finished lumber long enough to
span the distance between the desired installation location
on the mounting surface and the edges of the mounting
surface (figure 2-1).
Width of Mou
nting Surface
Cut a hole in the surface where the enclosure will be
installed and install the enclosure. The screw clamps
secure the enclosure to the tabletop. See “Preparing the
Table and Mounting the Enclosure” in this chapter.
5
Run all cables necessary to support the AC power,
RJ-45, and (for HSA 200 model only) video and audio
connectors. Leave enough slack in the cables to connect
them to the underside of the enclosure.
6
Turn off all of the equipment to be connected. Ensure that
the equipment connected to the RJ-45, video, and audio
connectors are all turned off and disconnected from the
power source.
7
Connect the power, video, audio, and RJ-45 cables to the
underside of the enclosure. See “Underside Features and
Cabling Connections” in this chapter.
8
On HSA 200SE and HSA 200CE models, set the gain
switch.
9
Connect and turn on the input and output devices.
10
For HSA 200SE and HSA 200CE model installations, the
picture should now appear and sound should be audible.
If not, ensure that all devices are plugged in and receiving
power. Check the cabling and gain setting, and make
adjustments as needed.
11
Peel the protective coating from the top surface.
Minimum
4 Screws
Wood
Strips
Wood Strip
Height
4" / 10.2 cm
Routing Template
Mounting
Surface
Edge
Wood Thickness
0.5" / 1.3 cm
Figure 2-1 — Prepared mounting template assembly
These strips raise the routing template above the mounting
surface to provide room for the router’s collar, protect the
mounting surface, and extend the reach of the routing
template so that it can be clamped to the edge of the surface.
2.
Using four or more short wood screws, secure the
mounting template to the lumber strips.
CAUTION
2-2
HSA 200/222 Series • Installation
Mounting
Surface
Edge
Do not allow the wood screws to protrude through
the bottom of the wooden strips. Protruding screws
will mar the table when the template is used.
HSA 200/222 Series • Installation
2-3
Installation, cont’d
Preparing the Table and Mounting the Enclosure
The preferred and recommended method for preparing the
table is to use the appropriate Extron routing template and a
router. See the part numbers for the templates in appendix A,
“Reference Information”.
For an HSA 200C, HSA 200CE, or HSA 222C unit (US version
only), another preferred method is to use a 6" hole saw.
Alternatively, for any model, you can use a paper cut-out
template (see appendix A, “Reference Information”) and a sabre
saw or keyhole saw, but this method is not recommended.
CAUTION
The opening in the table for the HSA enclosure
should be cut only by licensed and bonded
craftspeople. Exercise care to prevent scarring or
damaging the furniture.
The routing templates for the various HSA models
are not interchangeable. If you use the wrong
template, you will cut an improperly-sized hole. If
you use a larger template than required, the cut will
result in gaps in the table surface on either side of
the enclosure.
The surfaces of the HSA enclosure have screws and
other protruding hardware that could damage fine
furniture. Do not rest the enclosure on unprotected
furniture.
Figure 2-2 — Cutting the opening with a router
(example)
4.
Wear safety glasses when operating the router.
Failure to comply can result in eye injury.
Preparing the table with a router
1.
Locate the desired mounting location on the tabletop or
other installation surface. Mark the location.
2.
Place the mounting template assembly on the table,
centered on the mounting location. Angle the template for
the optimum positioning. If necessary, use a square to
ensure that the template is properly positioned. Extron is
not responsible for improperly-positioned HSA products.
CAUTION
3.
2-4
Using a router with a 5/8" (or 16 mm) outside diameter
guide bushing and a 1/2" (or 12 mm or 12.7 mm)
diameter straight router bit, carefully cut the opening in
the table surface (figure 2-2).
5.
Remove the clamps and the routing template.
The routing template is reusable. Do not discard the
template when the installation is complete. Save it to
install other HSA products of the same size.
Ensure that only the wooden strips contact the
furniture. Failure to do so may mar the furniture.
Once the template assembly is positioned properly, secure
the assembly to the table with clamps (figure 2-2).
HSA 200/222 Series • Installation
HSA 200/222 Series • Installation
2-5
Installation, cont’d
Preparing the table with a hole saw (HSA 200C,
HSA 200CE, or HSA 222C—US version only)
1.
Locate the desired mounting location on the tabletop or
other installation surface. Mark the 6" circle, then find the
center and mark it as well.
Wear safety glasses when operating the hole saw.
Failure to comply can result in eye injury.
2.
2.
Using a 6" hole saw on a portable drill, cut the mounting
hole at the desired location (figure 2-3). Extron is not
responsible for improperly positioned HSA products.
CAUTION
Remove the plastic strips that protect the corners of the
enclosure. If a sticky residue remains, remove it with an
appropriate metal cleaning product.
CAUTION
Do not use isopropyl alcohol or other solvents to clean
the HSA. Strong solvents will ruin some finishes.
3.
Carefully lower the HSA enclosure into the hole to test the
fit. If necessary, remove the enclosure and use a file or
rasp to enlarge or smooth the edges of the opening.
4.
From the underside of the table, reinstall the screw clamps
on the enclosure at a height at which the clamp will reach
the underside of the tabletop (figure 2-4).
Use a portable drill with sufficient power for the 6"
hole saw. Exercise caution when handling the drill
and hole saw. Care should be taken to protect the
surface of the tabletop, podium, or other mounting
surface from damage.
Figure 2-4 shows an HSA 200 installation. Except for
the video and audio connectors, the HSA 222 installation
is identical.
CAT6
Extron
HSA 200
Hideaway Surface
Access Enclosure
Output BNC
Connectors
(HSA 200 models only)
Mounting
Surface
Figure 2-3 — Cutting the opening with a hole saw
Installing the HSA enclosure (all)
Screw Clamp
Power Cord
1. Remove the screw clamps (2) on the sides of the enclosure.
CAUTION
2-6
The flanged edges of the top of the surface enclosure
are bevelled to an ultra-fine thickness of less than
0.04 (4/100)" (approximately 1 mm), and are
therefore very sharp. These edges are also soft and
may be easily nicked or bent. Exercise caution
when handling and mounting the enclosure.
Mishandling may result in injury to the installer or
damage the appearance of the enclosure.
HSA 200/222 Series • Installation
2 RJ-45 Connectors
Audio Cable
(HSA 200 models only)
Display BNC
Connectors
(HSA 200 models only)
Figure 2-4 — Mounting the HSA 200 or HSA 222
enclosure
HSA 200/222 Series • Installation
2-7
Installation, cont’d
Snugly tighten the Phillips head screws on the screw
clamps to secure the enclosure to the surface.
5.
Overtightening the Phillips head screws on the
screw clamps can bend the clamp’s horizontal
flange.
CAUTION
All HSA 200 models only
1
AC power outlet — Use this AC connector to:
•
6.
Tighten the locking thumbscrews on the screw clamps to
lock the clamp in position.
•
7.
Peel any remaining protective coating from the enclosure.
•
Plug in an external power supply to power the Extender
board on the HSA 200CE or HSA 200SE.
Provide AC power (5 amps max.) for loop through to one
additional HSA 200 unit.
Plug in a projector or other display device.
This outlet is a US-style power outlet on both the US/
domestic and international HSA 200 models. The power
output is the same voltage and frequency as the power
input.
Underside Features and Cabling Connections
Figure 2-5 shows the under-table connectors and other features
that present on HSA 200CE models. Other HSA 200 and
HSA 222 models have a subset of the same or similar features.
2
RGBHV video output — Connect the BNC cable from the
projector, plasma screen, or other display device to these female
BNC connectors.
HSA 200C and HSA 200S (no Extender board) — The output
from these connectors is an unbuffered pass-through from the
front panel VGA input.
HSA 200CE and HSA 200SE (Extender board) — The output on
these connectors is buffered by the Extender board.
MEDIUM
NORMAL
MAXIMUM
unity gain peaking & gain peaking & gain
POWER
9-18 VDC
AUDIO
R R
L L
HSA 200C and HSA 200S (no Extender board) only
4
1
On HSA 200 models with no Extender board, the audio
connection is part of the pigtail (figure 2-6).
*
Back View
2
8
*
11
9
●
13
●
**
●
HSA 200 Models Only
HSA 200CE/HSA 200SE
Units Only
3
10
●
12
✝
●
✝✝ HSA 200S/HSA 200C
(no Extender board) units only
Figure 2-6 — HSA 200S and HSA 200C audio connector
7
3
5
Audio output connection — This 3-pole direct insertion
terminal outputs unbalanced audio, passed through from the
front panel. Figure 2-7 shows how to wire the connector.
Unbalanced Output
6B
R
6A
L
Bottom View
Audio
Tip (L)
Sleeve/Ground
Tip (R)
Figure 2-7 — Unbuffered, unbalanced audio
connector wiring
Figure 2-5 — HSA 200CE under-table features
2-8
HSA 200/222 Series • Installation
HSA 200/222 Series • Installation
2-9
Installation, cont’d
All HSA 200 and HSA 222 models
4
Screw clamp bracket/screw clamp — These two brackets/
clamps hold the enclosure firmly in place in the mounting hole.
5
AC power input connection — Connect this cord to the power
source.
For US domestic versions, this power cord is
permanently connected to the HSA.
Connect the power cord to a 125VAC, 60 Hz,
5A power source.
For international versions, this power cord is a
removable IEC power cord. Connect the cord
to a 220-240V, 50-60 Hz, 5A power source.
7
Latch locking screws — These screws secure the latching
mechanism to the enclosure. They must be loosened in order to
adjust the top surface (see “Adjusting the Top Panel” in
chapter 3) with the top surface adjustment screw 8 .
8
Top surface adjustment screw — After loosening the latch
locking screws 7 , adjust the top surface of the tilt up panel with
this screw. Tighten the latch locking screws after adjustment.
9
Gas lift mounting plate — The lower end of the gas lift is
attached to this plate. The plate must be detached from the
enclosure in order to remove the gas lift.
HSA 200CE and HSA 200SE (Extender board) only
10
You can replace this connector with an optional Extron HSA 200/
HSA 222 Flexible Conduit Adapter kit (part #70-229-01).
6
Unbalanced Output
Balanced Output
R+ R-
Tip
Ring
Sleeve (s)
Tip
Ring
Audio
L+ L-
All RJ-45 connectors are teminated in accordance with
the TIA/EIA T 568 A standard.
R+ R-
Tip
See Caution
Sleeve (s)
Tip
See Caution
Audio
L+ L-
RJ-45 connectors — Plug one end of a CAT 5 or CAT 6 twisted
pair (TP) cable into each of these RJ-45 female connectors.
Connect the other end to an appropriate telecommunications or
data network or to an Extron TP product.
Figure 2-9 — Extender board audio
connector wiring
MEDIUM
Peaking and Gain
An RJ-11 (telephone) jack can be plugged directly into
the RJ-45 jack.
Ensure that the bottom RJ-45 connections match up with the
front panel RJ-45 connector locations (figure 2-8). For example,
match the front panel RJ-45 (CAT 6) network, data, or
communications connection 5A with the underside RJ-45
connector 6A , match 5B with 6B and so forth.
Audio output connection — This 5-pole direct insertion
terminal outputs unbalanced or balanced audio. Figure 2-9
shows how to wire the connector.
CAUTION
11
Connect the sleeve to
NORMAL
Unity Gain
ground (Gnd).
Connecting the sleeve to a
negative (-) terminal will
damage the audio output circuits.
MAXIMUM
Peaking and
Gain
Gain switch — To compensate for cable resistance and
capacitance, use a Tweeker to slide this switch to select the level
of video gain that yields the sharpest, smear-free picture.
Normal — unity gain (no signal boost)
Medium — mid-level peaking and gain
5A
6A
5B Front View
Adjust the gain before installing the HSA unit, as the
gain switch may be inaccessible after installation.
6B
Bottom View
Figure 2-8 — Configuration of RJ-45 connectors
2-10
Maximum — maximum amount of peaking and gain. Select
this setting for use with longer cables.
HSA 200/222 Series • Installation
12
Power supply connection — Plug the external power supply
(included) output wires into this 2-pole direct insertion
terminal. See “Power connector wiring” to wire the connector.
13
Power LED — Indicates when the Extender board is receiving
power.
HSA 200/222 Series • Installation
2-11
Installation, cont’d
Do not tin the stripped power supply leads. Tinned
wires are not as secure in the captive screw terminals
and could pull out.
Power connector wiring
1.
See figure 2-10. Plug the input connector of the included
100-240 VAC, 50/60Hz, 12 VDC power supply into the AC
power outlet on the underside of the enclosure ( 1 on
figure 2-5).
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before continuing.
To verify the polarity before connection, plug in the
power supply with no load and check the output with a
voltmeter.
Front Panel Connectors
Figure 2-12 shows the front panel of the HSA 200 models.
Figure 2-13 shows the front panel of the HSA 222.
MEDIUM
NORMAL
MAXIMUM
unity gain peaking & gain peaking & gain
POWER
9-18 VDC
AUDIO
R R
L L
2
3
HSA 200
4
Power Supply
Back View
●
Figure 2-10 — Powering the Extender board
This outlet is a US-style power outlet on both the US/
domestic and international HSA 200 models. The power
output is the same voltage and frequency as the power
input and is an acceptable power input to the power
supply included with the HSA.
2.
●
1
5B
HSA 200CE and
HSA 200SE Models Only
Figure 2-12 — HSA 200 front panel connectors
Insert the external power supply (included) output wires
into the 2-pole direct insertion captive screw terminal on
the Extender board (figure 2-11) and secure the wires.
125V
CAUTION
5A
HSA 222
50/60 Hz 5A
When connecting the power supply wires, voltage
polarity is extremely important. Applying power
with incorrect voltage polarity could damage the
power supply and the Extender board in the HSA.
125V
50/60 Hz 5A
CAT6
Black Wire
White Wire
12V
+
1
-
5A
5B
1
Figure 2-13 — HSA 222 front panel connectors
Captive Screw
Terminal
1
Figure 2-11 — Power connector wiring
2-12
HSA 200/222 Series • Installation
AC power outlet(s) — Plug a standard power cord into this
connector to provide AC power (5 amps max.) for a laptop or
other device. The power output will be the same voltage and
frequency as power input. The power outlet(s) will be
appropriate to the model.
HSA 200/222 Series • Installation
2-13
Installation, cont’d
The Universal AC outlet is fully compatible with
Europlug, British, Indian, Danish, and Italian plug
types. See the universal AC outlet guide on the Extron
Web site, www.extron.com, for compatibility details on
all plug types.
2
3
Computer video input (HSA 200 models only) — Plug the
VGA-UXGA output from a computer into this 15-pin HD female
connector.
5A
6A
5B Front View
6B
Audio input connector (HSA 200 models only) — Plug a
3.5 mm stereo plug into this jack for unbalanced audio input.
Figure 2-14 shows how to wire the male plug.
Tip (+)
Ring (-)
Bottom View
Figure 2-15 — Configuration of RJ-45 connectors
Sleeve ( )
Figure 2-14 — Audio input connector plug
4
Power/Signal LED (HSA 200SE and HSA 200CE only) — This
LED lights green when power and an input signal are present.
The LED lights amber when power is present but no input
signal is present.
5
RJ-45 connectors — Plug a CAT 5 or CAT 6 twisted pair (TP)
cable into each of these RJ-45 female connectors for network,
data, or communication connections.
Icon Label
Figure 2-16 — Changing the connector icon
When cabling the front panel and the underside of the enclosure
(figure 2-15), ensure that the bottom RJ-45 connections match up
with the front panel RJ-45 connector locations. For example,
match the front panel RJ-45 (CAT 6) network, data, or
communications connection 5A with the underside RJ-45
connector 6A and match 5B with 6B .
If necessary, on the front panel, have a qualified service person
replace the connector icon by prying the old icon off of the
connector plug-in with a Tweeker (figure 2-16) and snapping a
new icon in place.
2-14
HSA 200/222 Series • Installation
HSA 200/222 Series • Installation
2-15
Installation, cont’d
Pre-installation Testing and Troubleshooting
(HSA 200CE and HSA 200SE Models Only)
HSA 200/222 Series Surface Access Products
Before installing an HSA 200 with an Extender line driver into
furniture, test the system to make sure that the connections and
settings are correct.
1.
Apply power to the line driver. The power/signal LED on
the line driver will light to indicate that the line driver is
receiving power.
If the LED does not light, check the wiring at both the line
driver and the power supply, and ensure that the power
supply is connected to a power source.
If the image does not appear or there is no sound
1.
Make sure that all the devices are powered on.
2.
Ensure that the connectors are wired correctly at both ends
of the cables. Audio cables must be wired for an
unbalanced stereo input signal and for the appropriate
(unbalanced or balanced) output signal.
3.
If the input is from a laptop computer and no picture
appears, use a laptop breakout cable for the input
connection. Check the computer’s user’s guide or contact
Extron to determine if special commands are required to
output video to the external video port. Also, many
laptops’ screens shut off after the external video port is
activated.
4.
Call the Extron S3 Sales and Technical Support Hotline if
the image still does not appear or there is no sound.
If the image is not displayed correctly
1.
2.
3.
2-16
If the picture is too bright or too dark, or if the edges of the
image seem to exceed their boundaries, or if thin lines and
sharp edges look thick and fuzzy, change the gain setting.
If the picture appears and is stable, but it has ghosting or
blooming, verify that the video input is properly
terminated. If the problem is not resolved by changing the
termination, try using a different input cable. Poor quality
or damaged cable can cause ghosting and blooming.
If the picture still is not displayed correctly, call the Extron
S3 Sales and Technical Support Hotline.
HSA 200/222 Series • Installation
3
Chapter Three
Maintenance and Modifications
Removing and Replacing the Enclosure
Replacing the Bezels
Replacing the Gas Lift
Adjusting the Top Panel
Maintenance and Modifications
The most probable corrective maintenance procedures for your
HSA 200 or HSA 222 are leveling the top surface and replacing
the gas lifts. Most of the maintenance procedures require
removing the surface mount enclosure from the table.
Removing and Replacing the Enclosure
•
The procedure for replacing the bezel in an HSA 222 only
requires removing the HSA from the table.
•
The procedure for replacing the gas lift requires removing
the HSA 200 or HSA 222.
•
The procedure for levelling the top surface may require
removing the HSA.
The surfaces of the HSA enclosure have screws and other
protrusions that could damage fine furniture. Do not
rest the enclosure on unprotected furniture.
5.
Perform the desired maintenance procedure.
6.
If the surface is not level, adjust the top surface. See
“Adjusting the Top Panel” in this chapter.
7.
Carefully lower the HSA enclosure into the table opening.
8.
From the underside of the table, reinstall the screw clamps
on the enclosure at a height at which the clamp will reach
the underside of the tabletop.
9.
Snugly tighten the Phillips head screws on the screw
clamps to secure the enclosure to the surface.
Remove and replace the surface mount enclosure for
maintenance as follows:
CAUTION
Ensure that AC power is disconnected before
servicing the HSA unit.
Disconnect:
1.
2.
•
The IEC power cord
•
The RJ-45 connectors from the underside of the surface
mount enclosure
•
(HSA 200 models only) Any device plugged into the AC
power outlet
•
(HSA 200 models only) The BNC (video) connectors
•
(HSA 200 models only) The audio connector
•
(HSA 200CE and HSA 200SE only) The power supply
connector
Loosen the locking
thumbscrews on the screw
clamps to unlock the clamp.
3.
Loosen the screw clamps.
4.
Remove the screw clamps on
both sides of the enclosure.
Lift the enclosure from the table.
CAUTION
Screw
Clamp
Thumbscrew
The flanged edges of the top of the surface enclosure
are bevelled to an ultra-fine thickness of less than
0.04 (4/100)” (approximately 1 mm), and are
therefore very sharp. These edges are also soft and
may be easily nicked or bent. Exercise caution
when handling and mounting the enclosure.
Mishandling may result in injury to the installer or
damage the appearance of the enclosure.
3-2 HSA 200/222 Series • Maintenance and Modifications
Overtightening the Phillips head screws on the
screw clamps can bend the clamp’s horizontal
flange.
10.
Tighten the locking thumbscrews on the screw clamps to
lock the clamp in position.
11.
Reconnect all of the connectors removed in step 1.
Replacing the Bezels
The HSA ships with RJ-45/RJ-11 connector bezel plug-ins in a
variety of colors and a black, blank bezel.
To change to a different color connector
bezel or if a connector is not needed,
replace the connector bezel plug-in on the
front panel with a bezel of a different
color or a blank plug-in.
If no connector is desired, snap the
interior RJ-45 connector onto the rear of
the blank bezel plug-in to hold it conveniently out of the way.
Retain the removed connector bezel plug-in for later use.
Replace a bezel as follows:
1.
(HSA 222 models only) Remove the surface mount
enclosure from the table. See “Removing and Replacing
the Enclosure”, steps 1 through 4.
HSA 200/222 Series • Maintenance and Modifications 3-3
Maintenance and Modifications, cont’d
2.
(HSA 222 models only) Remove the four Phillips head
screws from the front access panel (figure 3-1). Retain the
screws. Lift the panel away from the enclosure.
3.
(HSA 222 models only) Disconnect both RJ-45 connectors
from the underside of the enclosure by simultaneously
performing steps 3a and 3b:
a.
With a Tweeker in one hand, reach through the small
access hole in the front of the enclosure (figure 3-2)
and gently pry outward on the front of the RJ-45
connector detent on the bezel plug-in,
— while you —
b.
Remove
front access
panel.
Reach your other hand through the front panel access
hole and tilt the connector back.
This disconnects the connector from the interior of the
lower enclosure without damaging the bezel plug-in.
Figure 3-1 — Removing the front access panel
(HSA 222 models)
Figure 3-2 — Releasing the bezel plug-in detent
(HSA 222 models)
3-4
HSA 200/222 Series • Maintenance and Modifications
HSA 200/222 Series • Maintenance and Modifications
3-5
Maintenance and Modifications, cont’d
4.
Remove the four 1/16" hex head screws on the right and
left sides of the front panel (figure 3-3). Retain the screws.
Lift the panel away from the enclosure.
8.
Snap the internal RJ-45 connector onto the back of the front
panel enclosure bezel plug-in.
9.
(HSA 222 models only) Reach your hand through the
front panel access hole and snap the lower internal RJ-45
connectors onto the back of the lower enclosure bezel
plug-ins.
10.
Replace the front panel in the surface mount enclosure and
secure it in place with the hex head screws removed in
step 4.
11.
(HSA 222 models only) Replace the front access panel in
the surface mount enclosure and secure it in place with the
Phillips head screws removed in step 2.
12.
(HSA 222 models only) Reinstall the surface mount
enclosure. See “Removing and Replacing the Enclosure”,
steps 6 through 11.
Figure 3-3 shows an HSA 200 model. Removing the
front panel from an HSA 222 is an identical procedure.
Remove 2 hex head
screws on each side.
240
- 50
/60
Hz
5A
HSA
AU
D
200
IO
Lift panel out
of enclosure.
Figure 3-3 — Removing the front panel
5.
With a Tweeker, push down on and
gently twist on the front of each RJ-45
connector detent to disconnect the
connector from the rear of the front panel
plug-in.
6.
Pinch the top and bottom bezel detents
together and push the bezel through the
front panel.
7.
Snap a replacement bezel in place. If necessary, replace the
connector icon by prying the old icon off of the connector
plug-in with a Tweeker (figure 3-4) and snapping a new
icon in place.
Icon Label
Figure 3-4 — Changing the connector icon
3-6
HSA 200/222 Series • Maintenance and Modifications
HSA 200/222 Series • Maintenance and Modifications
3-7
Maintenance and Modifications, cont’d
Replacing the Gas Lift
The gas lift that raises the HSA surface is rated for 100,000
opening and closing cycles. Contact the Extron S3 Sales &
Technical Support Hotline at the nearest phone number listed
on the rear cover of this manual to obtain a replacement gas lift.
Replace the gas lift as follows:
3.
Slide the gas lift mounting plate toward the center of the
enclosure, releasing the mounting plate (figure 3-5).
4.
Turn the gas lift mounting plate counterclockwise until the
plate comes free from the shaft of the gas lift (figure 3-5).
5.
Turn the surface mount enclosure onto its back side and
open the top panel.
Ensure that AC power is disconnected before
servicing the HSA unit.
CAUTION
1.
2.
When the HSA 200 is upside-down, the latch may
be ineffective. If the latch releases in this position,
the enclosure will tip and could damage the flanged
edges. Keep a free hand on the enclosure to keep it
from tipping.
Remove the surface mount enclosure from the table. See
“Removing and Replacing the Enclosure”, steps 1 through
4. Place the enclosure upside-down on a horizontal
surface. To protect the finish, place the enclosure on a soft
cloth.
With the gas lift removed, the top panel must be
manually lifted.
6.
(HSA 200 models only) Remove the four 1/16" hex head
screws on the right and left sides of the front panel
(figure 3-6). Retain the screws. Lift the panel away from
the enclosure.
Figure 3-6 shows an HSA 200 model. Removing the
front panel from an HSA 222 is an identical procedure.
Remove 2 hex head
screws on each side.
Loosen the three Phillips head screws that secure the gas
lift mounting plate in place (figure 3-5).
240
- 50
/60
Hz
5A
HSA
20
0
AU
D
IO
Unscrew mounting plate
from gas lift.
Lift panel out
of enclosure.
Figure 3-6 — Front panel removal (HSA 200 models)
Loosen (3)
screws.
Figure 3-5 — Removing the gas lift mounting plate
Figure 3-5 shows an HSA 200 model. Removing the gas
lift mounting plate from an HSA 222 is an identical
procedure.
3-8
HSA 200/222 Series • Maintenance and Modifications
HSA 200/222 Series • Maintenance and Modifications
3-9
Maintenance and Modifications, cont’d
7.
(HSA 222 models only) Remove the four Phillips head
screws from the front access panel (figure 3-7). Retain the
screws. Lift the panel away from the enclosure.
8.
Remove the pivot nut from the upper pivot bolt, then
remove the bolt, releasing the upper end of the gas lift
from the top panel. Pull the gas lift from the bottom of the
enclosure.
HSA 200 models — Reach through the front panel
opening (figure 3-8).
HSA 222 models — Reach through the front access panel
(figure 3-9 on page 3-12).
Top Clevis
Pivot Nut
Pivot Bolt
Remove
front access
panel.
Figure 3-7 — Front access panel removal (HSA 222
models)
Piston End
Gas Lift
Figure 3-8 — Replacing the gas lift, HSA 200 model
3-10 HSA 200/222 Series • Maintenance and Modifications
HSA 200/222 Series • Maintenance and Modifications 3-11
Maintenance and Modifications, cont’d
Adjusting the Top Panel
Level the top panel of the HSA 200 or HSA 222 as follows:
Remove
pivot nut.
1.
If necessary to view the top and the underside of the
enclosure simultaneously, remove the surface mount
enclosure from the table. See “Removing and Replacing
the Enclosure”, steps 1 through 4.
2.
Close and latch the top panel.
3.
Slightly loosen the two latch locking screws (figure 3-10)
on the underside of the surface mount enclosure. These
screws lock the latch in place once it is adjusted.
Adjustment
Screw
Remove
gas lift.
Figure 3-9 — Replacing the gas lift, HSA 222 model
9.
10.
Insert the piston end of the replacement gas lift through
the hole in the bottom of the enclosure adjacent to the latch
and secure the lift in the clevis on the top panel with the
nut and bolt that were removed in step 8.
(HSA 200 models only) Replace the front panel in the
surface mount enclosure and secure it in place with the
hex head screws removed in step 6.
11.
(HSA 222 models only) Replace the front access panel in
the surface mount enclosure and secure it in place with the
Phillips head screws removed in step 7.
12.
Thread the pivot nut on the gas lift mounting plate onto
the shaft of the gas lift and tighten it several turns.
13.
14.
Firmly push the gas lift mounting plate into position on
the underside of the surface mount enclosure, engaging
the three mounting screws that were loosened in step 2.
Holding the plate in position with one hand, secure it to
the enclosure with the three screws.
Latch Locking
Screws
Figure 3-10 — Adjusting the top panel
4.
Gently turn the adjustment screw on the rear of the surface
mount enclosure to raise or lower the top panel to level it
with the flange. Turning the screw counterclockwise raises
the panel and clockwise lowers the panel.
5.
Once the top panel is level, tighten the two latch locking
screws on the underside of the surface mount enclosure.
6.
If the surface mount enclosure was removed, reinstall it. See
“Removing and Replacing the Enclosure”, steps 7 through 11.
Reinstall the surface mount enclosure. See “Removing and
Replacing the Enclosure”, steps 6 through 11.
3-12 HSA 200/222 Series • Maintenance and Modifications
HSA 200/222 Series • Maintenance and Modifications 3-13
Maintenance and Modifications, cont’d
HSA 200/222 Series Surface Access Products
A
Appendix A
Reference Information
Specifications
HSA Part Numbers
Included Parts
Routing Templates
Replacement Parts
Accessories
Top Plate Dimensions
3-14 HSA 200/222 Series • Maintenance and Modifications
Reference Information
Audio — HSA 200SE, HSA 200CE
Specifications
Video — HSA 200SE, HSA 200CE
Gain .................................
Bandwidth .....................
Selectable: unity (0.7 V), (0.75 V) 50%, (0.8 V)
100%
300 MHz (-3 dB)
ID bits are terminated on pins 4 and 11.
Video input — HSA 200S, HSA 200C
Number/signal type ....
Connectors .....................
1 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs
(1) 15-pin HD female
Video input — HSA 200SE, HSA 200CE
Number/signal type ....
Connectors .....................
Nominal level ................
Min./max. levels ...........
Impedance ......................
Horizontal frequency ...
Vertical frequency .........
1 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs
(1) 15-pin HD female
0.7 Vp-p for RGB
Analog: 0.3 V to 1.5 Vp-p with no offset at unity
gain
75 ohms
15 kHz to 135 kHz
30 Hz to 170 Hz
Video output — HSA 200S, HSA 200C
Number/signal type ....
Connectors .....................
1 pass-through VGA–UXGA RGBHV, RGBS,
RGsB, RsGsBs
5 BNC female on pigtails
Video output — HSA 200SE, HSA 200CE
Number/signal type ....
Connectors .....................
Nominal level ................
Min./max. levels ...........
Impedance ......................
DC offset ........................
1 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs
5 BNC female on pigtails
0.7 Vp-p for RGB
Analog: 0.3 V to 1.5 Vp-p
75 ohms
±5 mV with input at 0 offset
Sync — HSA 200SE, HSA 200CE
Input type .......................
Output type ...................
Input level ......................
Output level ...................
Input impedance ...........
Output impedance ........
Max. propagation delay
Max. rise/fall time ........
Polarity ...........................
A-2
Gain .................................
Frequency response ......
THD + Noise ..................
Unbalanced output: 0 dB; balanced output: +6 dB
20 Hz to 20 kHz, ±0.5 dB
0.025% @ 1 kHz, 0.020% @ 20 kHz at nominal
level
S/N ................................. >90 dB at rated maximum output (21 dB,
balanced)
Stereo channel separation >75 dB @ 20 Hz to 20 kHz
Audio input — HSA 200S, HSA 200C
Number/signal type ....
Connectors .....................
1 stereo, unbalanced
(1) 3.5 mm stereo female jack
Audio input — HSA 200SE, HSA 200CE
Number/signal type ....
Connectors .....................
Impedance ......................
Nominal level ................
Maximum level .............
1 stereo, unbalanced
(1) 3.5 mm stereo female jack
>10k ohms unbalanced, DC coupled
-10 dBV (316 mVrms)
+6 dBu, (balanced or unbalanced) at 1%THD+N
Audio output — HSA 200S, HSA 200C
Number/signal type ....
Connectors .....................
1 pass-through stereo, unbalanced
(1) 3.5 mm, direct insertion captive screw
connector, 3 pole
Audio output — HSA 200SE, HSA 200CE
Number/signal type ....
Connectors .....................
Impedance ......................
Nominal level ................
Max. level (Hi-Z) ...........
Max. level (600 ohm) ....
1 stereo, balanced/unbalanced
(1) 3.5 mm direct insertion captive screw
connector, 5 pole
50 ohms unbalanced, 100 ohms balanced
Unbalanced output: -10 dBV (316 mVrms)
Balanced output: -2 dBu (632 mVrms)
>+14 dBu, balanced at 1% THD+N
>+5.5 dBm, balanced at 1% THD+N
0 dBu = 0.775 Vrms. 0 dBV = 1 Vrms. 0 dBV
2 dBu.
RGBHV, RGBS, RGsB, RsGsBs
RGBHV, RGBS, RGsB, RsGsBs
2.0 V to 5.0 Vp-p
TTL: 5.0 Vp-p, unterminated
510 ohms
75 ohms
18.8 ns
4 ns
Positive or negative (follows input)
HSA 200/222 Series • Reference Information
HSA 200/222 Series • Reference Information
A-3
Reference Information, cont’d
General
The Universal AC outlet is fully compatible with Europlug,
British, Indian, Danish, and Italian plug types. See the
Universal AC outlet guide on the Extron Web site,
www.extron.com, for compatibility details on all plug types
Power (HSA 200SE/CE) Supplied by an external power supply
External power supply (HSA 200SE/CE)
100 VAC to 240 VAC, 50-60 Hz, external;
to 12 VDC, 0.42 A, regulated
Power input requirements (HSA 200SE/CE)
12 VDC, 0.2 A
Temperature/humidity — HSA 200SE/CE
Storage: -40 to +158°F (-40 to +70°C) / 10% to
90%, noncondensing
Operating: +32 to +122°F (0 to +50°C) / 10% to
90%, noncondensing
Rack mount .................... No, but furniture mountable
Enclosure type ............... Metal
Enclosure dimensions
CAUTION
Use the appropriate metal Extron routing template or refer to
the surface cutout dimensions here before cutting a hole in the
furniture or other surface. Pay special attention to the direction
the unit will face; the unit’s connector access side is underlined.
Extron is not responsible for miscut mounting holes.
HSA 200S, HSA 200SE — USA models
Top plate (outer rim) ................... 6.470" W x 5.125" D
(16.43 cm W x 13.02 cm D)
Surface cutout (inside rim) ......... 5.970 ±0.0325" W x 4.625 ±0.0325" D
(15.16 ±0.083 cm W x 11.75 ±0.083 cm D)
Top plate (inside tilt plate) ......... 4.344" W x 3.000" D
(11.03 cm W x 7.62 cm D)
HSA 222S — USA model
Top plate (outer rim) ................... 6.470" W x 5.125" D
(16.43 cm W x 13.02 cm D)
Surface cutout (inside rim) ......... 5.970 ±0.0325" W x 4.625 ±0.0325" D
(15.16 ±0.083 cm W x 11.75 ±0.083 cm D)
Top plate (inside tilt plate) ......... 4.660" W x 2.875" D
(11.84 cm W x 7.30 cm D)
A-4
HSA 200/222 Series • Reference Information
HSA 200C, HSA 200CE — USA models
Top plate (outer rim) ................... 6.500" diameter circle
(16.51 cm diameter) circle
Surface cutout (inside rim) ......... 6.000 ±0.0325" diameter circle
(15.24 ±0.083 cm diameter) circle
Top plate (inside tilt plate) ......... 4.344" W x 3.000" D
(11.03 cm W x 7.62 cm D)
HSA 222C — USA model
Top plate (outer rim) ................... 6.500" diameter circle
(16.51 cm diameter) circle
Surface cutout (inside rim) ......... 6.000 ±0.0325" diameter circle
(15.24 ±0.083 cm diameter) circle
Top plate (inside tilt plate) ......... 4.660" W x 2.875" D
(11.84 cm W x 7.30 cm D)
HSA 200S, HSA 200SE, HSA 200C, HSA 200CE — USA models
Box (under surface) ..................... 4.0" H x 4.6" W (front of unit) x 4.4" D
(10.2 cm H x 11.7 cm W x 11.2 cm D)
without clamps
4.0" H x 8.0" W (front of unit) x 4.4" D
(10.2 cm H x 20.3 cm W x 11.2 cm D)
with clamps
HSA 222S, HSA 222C — USA models
Box (under surface) ..................... 5.6" H x 5.3" W (front of unit) x 3.6" D
(14.2 cm H x 13.5 cm W x 9.1 cm D)
without clamps
5.6" H x 8.6" W (front of unit) x 3.6" D
(14.2 cm H x 21.8 cm W x 9.1 cm D)
with clamps
HSA 200S/HSA 200SE — international square models
Top plate (outer rim) ................... 8.183" W x 6.375" D
(20.79 cm W x 16.19 cm D)
Surface cutout (inside rim)
7.683 ±0.0325" W x 5.875 ±0.0325" D
(19.51 ±0.083 cm W x 14.92 ±0.083 cm D)
Top plate (inside tilt plate)
5.90" W x 4.10" D
(14.99 cm W x 10.41 cm D)
HSA 222S — international square models
Top plate (outer rim) ................... 8.183" W x 6.375" D
(20.78 cm W x 16.19 cm D)
Surface cutout (inside rim) ......... 7.683 ±0.0325" W x 5.875 ±0.0325" D
(19.51 ±0.083 cm W x 14.92 ±0.083 cm D)
Top plate (inside tilt plate) ......... 6.183" W x 3.75" D
(15.70 cm W x 9.53 cm D)
HSA 200/222 Series • Reference Information
A-5
Reference Information, cont’d
HSA 200C/HSA 200CE — international circular models
Top plate (outer rim) ................... 8.5" diameter circle
(21.6 cm diameter) circle
Surface cutout (inside rim) ......... 8.0" diameter (20.3 cm diameter) circle
Top plate (inside tilt plate) ......... 5.9" W x 4.1" D
(15.1 cm W x 10.4 cm D)
HSA 200 — international, all models
Box (under surface) ..................... 4.0" H x 6.3" W (front of unit) x 5.0" D
(10.2 cm H x 15.9 cm W x 12.7 cm D)
without clamps
4.0" H x 10.0" W (front of unit) x 5.0" D
(10.2 cm H x 25.3 cm W x 12.7 cm D)
with clamps
HSA 222 — international, all models
Box (under surface) ..................... 4.5" H x 6.6" W (front of unit) x 4.9" D
(11.4 cm H x 16.8 cm W x 12.4 cm D)
without clamps
4.5" H x 10.3" W (front of unit) x 4.9" D
(11.4 cm H x 26.2 cm W x 12.4 cm D)
with clamps
Product weight
HSA 200S, HSA 200C ................. 4.0 lbs (1.8 kg)
HSA 222S, HSA 222C ................. 3.5 lbs (1.6 kg)
HSA 200SE, HSA 200CE .............. 5.0 lbs (2.3 kg)
Shipping weight
HSA 200S, HSA 200C, HSA 222S, HSA 222C
7 lbs (4 kg)
HSA 200SE, HSA 200CE ............. 8 lbs (4 kg)
Vibration ............................................. ISTA 1A in carton
(International Safe Transit Association)
Listings, certifications ....................... UL, c-UL
Compliances
HSA 200SE, HSA 200CE ............. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ................................................... 30,000 hours
Warranty ............................................. 3 years parts and labor
HSA Part Numbers
HSA 200S
Part number
HSA 200S US/domestic (black anodized finish)
60-510-01
HSA 200S International
60-705-nn
HSA 200SE
Part number
HSA 200SE US (black anodized finish)
60-511-01
HSA 200SE International
60-706-nn
HSA 200C
Part number
HSA 200C US/domestic (black anodized finish)
60-512-01
HSA 200C International
60-703-nn
HSA 200CE
Part number
HSA 200CE US/domestic (black anodized finish)
60-513-01
HSA 200CE International
60-704-nn
HSA 222
Part number
HSA 222S US/domestic (black anodized finish)
60-630-01
HSA 222C US/domestic (black anodized finish)
60-631-01
HSA 222S International
60-701-nn
For the international versions, the nn in the part number
identifies the AC power connector and finish (black
anodized or brushed aluminum). Specify the desired
power connector and finish when ordering.
The USA versions of the HSA 200 and HSA 222 are also
available in a brushed aluminum finish. Visit the Extron
Web site, www.extron.com for more part numbers.
All nominal levels are at ±10%
Specifications are subject to change without notice.
A-6
HSA 200/222 Series • Reference Information
HSA 200/222 Series • Reference Information
A-7
Reference Information, cont’d
Included Parts
Part
HSA 200S/HSA 200SE/HSA 222S US Models
6.470" (16.43 cm)
Part number
HSA 200 and HSA 222 User’s Manual
5.970 + 0.0325" (15.16 + 0.083 cm)
RJ-45 connector bezel plug-in inserts (assorted colors) 70-201-01
Power supply, 100-240VAC, 50/60Hz, 12VDC
(HSA 200SE and HSA 200 CE only)
SURFACE CUT-OUT
AREA = 5.970 + 0.0325"
(15.16 + 0.083 cm) x 4.625 + 0.0325"
(11.75 + 0.083 cm) 4.625 + 0.0325"
28-104-01
Tweeker
Routing Templates
Template
(11.75 + 0.083 cm)
Part number
HSA 200/HSA 222 US routing template
70-237-01
HSA 200/HSA 222 International routing template
70-237-02
0.5"
(1.3 cm)
Accessories
Part
5.125"
(13.02 cm)
Part number
HSA 200 RJ-45 to RJ-11 Conversion Kit
70-231-01
HSA 222 RJ-45 to RJ-11 Conversion Kit
70-231-02
HSA 200/HSA 222 Flexible Conduit Adapter Kit
70-229-01
Top Plate Dimensions
Cut-Out Radius:
0.25" (0.6 cm)
Tilting Plate
Top Panel
Cut surface material
out along this line.
User Access (Connectors and AAP Openings)
TEMPLATE IS NOT FULL SIZE.
HSA 200S/HSA 200SE International Models
8.183" (20.78 cm)
The cutout dimension illustrations (figures A-1 and A-2) are not
to scale and are for reference only. If you choose not to use
Extron’s metal routing template (chapter 2, “Installation”), the
dimensions on the illustrations will help you properly prepare
the mounting surface. The surface cutout area is the shaded area
on the diagrams. The cutout dimensions are provided.
7.683 + 0.0325" (19.51 + 0.083 cm)
SURFACE CUT-OUT
AREA = 7.683 + 0.0325"
(19.51 + 0.083 cm) x 5.875 + 0.0325"
(14.92 + 0.083 cm)
For full size paper templates, visit the Extron Web site
(www.extron.com) or call the Extron S3 Sales & Technical
Support Hotline.
6.375"
(16.19 cm)
5.875 + 0.0325"
(14.92 + 0.083 cm)
0.5"
(1.3 cm)
Cut-Out Radius:
0.25" (0.6 cm)
Tilting Plate
Top Panel
Cut surface material
out along this line.
User Access (Connectors and AAP Openings)
TEMPLATE IS NOT FULL SIZE.
Figure A-1 — HSA 200S/HSA 200SE/ HSA 222S cutout dimensions
A-8
HSA 200/222 Series • Reference Information
HSA 200/222 Series • Reference Information
A-9
Reference Information, cont’d
HSA 200C/HSA200CE/HSA222C US Models
6.5" (16.5 cm)
6.000 + 0.0325" (15.24 + 0.083 cm)
SURFACE CUT-OUT
AREA = 6.000 + 0.0325"
(15.24 + 0.083 cm) diameter
Cut surface material
out along this line.
Tilting Plate
Top Panel
User Access (Connectors and AAP Openings)
TEMPLATE IS NOT FULL SIZE.
HSA 200C/HSA 200CE International Models
8.5" (21.6 cm)
8.0" (20.3 cm)
HSA 200/222 Series Surface Access Products
B
Appendix B
Packaging for Shipment
SURFACE CUT-OUT
AREA = 8.0"
(20.3 cm) diameter
Cut surface material
out along this line.
Top Panel
Tilting Plate
User Access (Connectors and AAP Openings)
TEMPLATE IS NOT FULL SIZE.
Figure A-2 — HSA 200C/HSA 200CE/HSA 222C cutout dimensions
A-10
HSA 200/222 Series • Reference Information
Packaging for Shipment
The HSA 200’s and HSA 222’s ultra-fine machined surfaces and
moving parts make them vulnerable to damage caused by
mishandling during shipment, if they are improperly packaged.
If, for any reason, you need to return an HSA to Extron, first
contact Extron to obtain a return kit. The return kit, which
reduces the chances of damage during shipment, includes a
sturdy shipping carton and foam shells custom cut to fit the
HSA (figure B-1).
2.
Disconnect all cables and remove the HSA 200 or HSA 222
from the table or desk. See “Removing and Replacing the
Enclosure”, steps 1 through 4, in chapter 3, “Maintenance
and Modifications”.
3.
Place the enclosure on a flat, horizontal surface. To protect
the finish, place it on a soft cloth or rubber mat.
4.
Install the plastic strip (part of the return kit) to protect the
flanged edges of the top of the enclosure (figure B-2).
Figure B-2 — Installing protective strips
5.
Figure B-1 — HSA 200/HSA 222 return kit
Open the top panel and insert the HSA 200 or HSA 222
into the custom cutout portion of one of the foam shells
(figure B-3).
Package an HSA for shipment as follows:
1.
Contact the Extron S3 Sales & Technical Support Hotline to
obtain a return kit. Extron will send the return kit to the
location you specify.
The flanged edges of the top of the surface
enclosure are sharp when the HSA is removed from
the table. Exercise caution when handling to
prevent personal injury.
CAUTION
B-2
The flanged edges of the top of the surface
enclosure are bevelled to an ultra-fine thickness of
less than 0.04 (4/100)” (approximately 1 mm).
These edges are soft and can be easily nicked or
bent. Exercise caution when handling and
mounting the enclosure. Mishandling can damage
the appearance of the enclosure.
HSA 200/222 Series • Packaging for Shipment
Figure B-3 — Installing the HSA into the foam
shell
HSA 200/222 Series • Packaging for Shipment
B-3
Packaging for Shipment, cont’d
6.
Place the remaining foam shell on the other side of the
HSA (figure B-4). Firmly push the foam shells together as
far as they will go to completely suspend the HSA unit.
Figure B-4 — HSA unit suspended in the foam
7.
Place the foam-protected HSA 200 or HSA 222 into the
shipping carton (figure B-5).
Figure B-5 — HSA in the shipping carton
B-4
8.
Close the shipping carton and seal it with high quality
shipping tape.
9.
Ship the HSA to Extron using a reputable shipping
company.
HSA 200/222 Series • Packaging for Shipment

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement