Lenco SCD-32 BT Instruction manual
Lenco SCD-32 BT is a versatile audio system that combines a portable radio, CD player, and Bluetooth connectivity in one compact device. With its sleek design and user-friendly controls, it offers a variety of features to enhance your listening experience. Enjoy your favorite CDs, listen to FM radio stations, or stream music wirelessly from your Bluetooth-enabled devices. The SCD-32 BT also allows you to program your favorite tracks, adjust the sound with its volume control, and use headphones for private listening.
Advertisement
Advertisement
DATE : 17 / 08 / 16 , MODEL : SR24NBT / CD VERSION / ERP2 + BLUETOOTH ,
LENCO SCD-32 BT , ENGLISH I/M , 230V~ 50Hz ,
FM ONLY 87.5-108 MHz
TCD19A , W / PHONES ( ONLY )
Portable radio with CD and Bluetooth
SCD-32 BT
INSTRUCTION MANUAL
For information and support, www.lenco.com
WARNING
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power laser device.
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local voltage.
ON CONDENSATION
• When left in a heated room where it is warm and damp,water droplets or condensation may form inside the CD player.
• When there is condensation inside the unit, the unit may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
* Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.
* Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc..
* Do not place naked flame sources, such as lighted candles on the apparatus.
* Take attention to the environmental aspects of battery disposal.
* Use the apparatus only in moderate climates (not in tropical climates).
* Do not expose the apparatus to dripping or splashing.
* Do not place objects filled with liquids, such as vases, on the apparatus.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
“To be completely disconnect the power input, the mains plug of apparatus shall be disconnected from the mains.” as the disconnect devices is the mains plug of apparatus.
“The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use.”
“Excessive sound pressure from earphones and headphones can cause hearing loss.”
“Battery shall not be exposed to excessive heat such as sunshine, fire or the like.”
The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION : To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside the unit. Refer all servicing to qualified personnel.
The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from mains supply.
THE MARKING PLATE IS LOCATED AT THE BACK OF ENCLOSURE OF THE APPARATUS
LOCATION OF CONTROLS
1. CD PROGRAM / CLOCK-ADJ. BUTTON
2. CD PLAY MODE BUTTON
3. STANDBY BUTTON
4. BLUETOOTH INDICATOR
5. CD DISPLAY
6. SPEAKER
7. CD DOOR
8. TELESCOPIC ANTENNA
9. OPEN / CLOSE CD BUTTON
10. FM STEREO INDICATOR
11. CD NEXT BUTTON
12. CD PLAY / PAUSE BUTTON
GB 1
13. CD BACK BUTTON
14. CD STOP BUTTON
15. DIAL SCALE
16. MODE SWITCH
17. TUNING CONTROL
18. AC SOCKET
19. CARRYING HANDLE
20. VOLUME CONTROL
21. FUNCTION SWITCH
22. PHONES JACK
23. BATTERY COMPARTMENT
POWER SUPPLY
USING HOUSE CURRENT
Before use, check that the rated voltage of your unit matches your local voltage.
Note: Plug is used as the disconnect device.
The disconnect device shall remain readily
operable.
USING BATTERIES
Disconnect the AC power cord from the AC inlet of the unit. Battery power is cut automatically by the cord while it is connected.
To AC socket
To AC outlet
When the volume decrease, or the sound distorts, replace all of the batteries with new ones.
battery door
Insert 6 UM-2
( size C ) batteries.
TURN ON / OFF THE SYSTEM
Press the STANDBY button to turn the audio on.
To change the audio mode between CD, RADIO AND
BLUETOOTH ,set the FUNCTION switch while the power is on.
The audio mode is displayed.
Turn off the unit by pressing the STANDBY button.
" OFF " word will be shown on the display and then resume the current time.
STANDBY
LCD display
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
VOLUME
FOR PRIVATE LISTENING
Plug in headphones (ø3.5 mm stereo mini-plug) to the
PHONES jack.
When headphones are plugged in, the speakers are automatically disconnected.
MAX.
MIN.
VOLUME
CLOCK ADJUSTMENT
The clock is displayed on LCD display at standby mode.
1. Press and hold the PROGRAM / CLOCK-ADJ. button.
2. Press the NEXT or BACK to select 12 hours or 24 hours display.
3. Press the PROGRAM / CLOCK-ADJ. button, the hour digit flash.
4. Press the NEXT or BACK to adjust hour digit.
5. Press the PROGRAM / CLOCK-ADJ. button, the minute digit flash.
6. Press the NEXT or BACK to adjust minute digit.
7. Press the PROGRAM / CLOCK-ADJ. button again, the correct time is shown on display.
LCD display
GB 2 CLOCK-ADJ.
LISTENING TO THE RADIO
1 . Turn on the unit by pressing the STANDBY button.
STANDBY
2 . Set to RADIO
FUNCTION
RADIO
LCD display
3 . Select a MODE.
FM MONO
MODE
FM ST.
4 . Tune in to a station.
TUNING
5 . Adjust the sound.
VOLUME
MAX.
VOLUME
MIN.
FOR BETTER RECEPTION
FM
NOTE : 1. FM stereo LED indicator lights if receive FM stereo broardcast and the MODE switch set on "FM STEREO".
2. When too much noise is heard during FM STEREO reception, set MODE switch to FM mono.
AFTER LISTENING
Turn off the unit by pressing the STANDBY button.
COMPACT DISC PLAYBACK
1 . Turn on the unit by pressing the STANDBY button.
2 . Set to CD
FUNCTION
CD
STANDBY
GB 3
3 . Open the CD door by pushing
CD Door Open / Close button.
TO INTERRUPT PLAYBACK
Press the Play/ Pause button and the symbol " " will be flashed. Press the button again to resume playback.
4. Insert a disc with the label side facing up.
5 . Close the CD door.
The disc will rotate and the total tracks of the disc will show on the display.
6. Press the PLAY/PAUSE button.
Track number "01" & the symbol " " will be
shown.
CD display
TO STOP PLAYBACK
Press the STOP button and the display shows the total tracks of the disc.
CD display
•
•
•
TO SKIP TO THE BEGINNING OF A TRACK
• Press either one of the skip buttons according to the desired skip direction.
Play/back resumes from the selected track.
When the button is pressed once during play, the previous track starts again.
When the button is pressed once during play, the next track plays.
SEARCHING FOR A PASSAGE WITHIN A TRACK
• Keep the or button pressed during playback, and release the button as soon as you recognise the desired passage. Then normal CD playback will resume from this point.
Unit will be automatically off within 30mins without futhur operation (in stop mode / CD door open).
REPEAT , REPEAT ALL AND MIX PLAYBACK
Press PLAY MODE button during stop mode. CD plays with a single track repeat, all tracks repeat or randomly.
FOR NORMAL COMPACT DISC PLAYBACK
Mode sequence REPEAT >> REPEAT ALL >> MIX >> CLEAR.
During Repeat 1 mode, display shows
During Mix mode, display shows
CD display
During Repeat 2 mode, display shows
CD display
GB 4
PROGRAMMED PLAYBACK
PROGRAMMED PLAYBACK
Programmed playback enables tracks on a disc to be played in the desired order. Up to 20 tracks can be programmed.
1. Press the " PROGRAM " button.
2. Press the " NEXT " and " BACK " buttons to select the desired track number.
3. Press the " PROGRAM " button again to memorize the track.
4. Repeat steps 2 and 3 until all desired tracks are programmed.
5. Press the " PLAY/PAUSE " button to start.
" " , " PROG " & track number are shown on the CD display.
6. Press the " STOP " button once to stop programmed playback.
7. Press the " PLAY/PAUSE " button to resume programmed playback.
8. Open the CD door, turn off the CD player or press the
" STOP " button twice to clear the programmed memory.
Note : Programming can only be made when the player
is in stop mode.
" PROGRAM "
CD display
Note on CD-R/RW discs
PROGRAM
- Because of non-standardized format definition/ production of CD-R/RW, playback quality and performance are not
guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions, such as PC performance,
writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- It is recommended to record only audio files on CD-R/RW discs for easy reading.
BLUETOOTH OPERATION
1. Press the STANDBY button. 3 . On your Bluetooth device, activate Bluetooth and search for LENCO SCD-32 BT. The bluetooth LED indicator flashes during pairing.
" BLUETOOTH "
STANDBY
2 . Set to BLUETOOTH, the " BT " is shown on the display.
4. Connected : Bluetooth LED indicator is always light
on.
5. After successful coonection,start music play on the
Bluetooth device.
LCD display
- Next time you switch on the unit, the speaker connects to the last paried device automatically.
- The music streaming may be interrupted by obstacles between the device and the unit, such as walls, or other devices
nearby that operate in the same frequency.
Unit will be automatically off after 10 mins without further operation .
GB 5
MAINTENANCE
CLEANING A CD
If the CD skips or will not play , the disc may need cleaning
. Before playing, wipe the disc from the centre out with a cleaning cloth. After playing, store the disc in its case.
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower.
Blow several times on the lens and remove the dust with the brush. Finger prints may be removed with a cotton swab moistened with alcohol.
SPECIFICATIONS
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTE
If an abnormal display indication or an operating problem occurs, disconnect the AC power cord and remove the batteries. Wait at least 5 seconds, then reconnect the AC power cord or reinstall the batteries.
WARNING
Should the CD door be opened before the reading of the CD is completed, a jamming noise may occur. This is resolved by closing the CD door.
CD SECTION
Channels:
S / N ratio:
Wow & Flutter:
Sampling frequency:
Quantization:
Pick up light source:
Pick up wave length
2 channels
60 dB undetectable
44.1 kHz 8 x over sampling
1 bit DA converter
Semi - conductor laser
790 nm
BLUETOOTH SECTION
Bluetooth standard
RADIO SECTION
Tuning ranges:
Antennas:
Bluetooth Standard Version 2.1 + EDR
Range : 10 m ( free space )
FM 87.5 - 108 MHz
FM Rod antenna
GENERAL
Output power:
Power consumption:
Speaker:
1 W + 1 W (RMS)
12 W
3 " 8 OHM
3.5 MM Phones jack:
Power source: AC : 230V ~ 50Hz
DC : 9V ( 6 x 1.5V LR14/ "C"/UM2 )
Dimensions:
Weight
224(L) x 234(D) x 126(H)mm
1.43 KGS
Due to continuing improvement, the features and the design are subject to change without notice.
This product operates at 2400 - 2483.5 MHz and is designated only to be used inside a normal household environment.
This product is suited for this purpose within all EU counties.
GB 6
Guarantee
Lenco offers service and warranty in accordance with the European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the description made in this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic
Equipment Directive).
CE Marking
Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive
(2014/35/EU) issued by the Commission of the European Community.
Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at [email protected]
WARNING: Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.
Where to place the item :
Today’s furniture is coated with a wide variety of lacquers and synthetic-coatings that are treated with an extensive range of cleaning products. Therefore, the possibility that some of these substances contain components that react adversely to the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause discoloring to furniture surfaces. If necessary, place the appliance on a non-slide surface.
®All rights reserved
Service
For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, Nuth, The Netherlands
GB 7

Public link updated
The public link to your chat has been updated.
Advertisement