- Entertainment & hobby
- Musical instruments
- Musical Instrument Amplifier
- Fender
- Bullet 150
- User's manual
advertisement
2
ENGLISH - PAGES . . . . . . 6-7
F C C C o m p l i a n c e N o t i c e : This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instructions, may cause harmful interference to radio communications and there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit different from that of the receiver. Consult the dealer or an experienced radio/TV technician if help is needed.
ESPAÑOL - PAGINAS . . . . 8-9
FRANÇAIS - PAGES . . . . . 10-11
ITALIANO - PAGINE . . . . . 12-13
DEUTSCH - SEITEN . . . . . 14-15
. . . . . . . . . . 16-17
I m p o r t a n t S a f e t y I n s t r u c t i o n s
This symbol warns the user of dangerous voltage levels localized within the enclosure.
This symbol advises the user to read all accompanying literature for safe operation of the unit.
∆
Read, retain, and follow all instructions. Heed all warnings.
∆
Only connect the power supply cord to an earth grounded AC receptacle in accordance with the voltage and frequency ratings listed under INPUT POWER on the rear panel of this product.
∆
WARNING: To prevent damage, fire or shock hazard, do not expose this unit to rain or moisture.
∆
Unplug the power supply cord before cleaning the unit exterior
(use a damp cloth only). Wait until the unit is completely dry before reconnecting it to power.
∆ During operation: Maintain at least 6 inches (15.25 cm) of unobstructed air space around the unit to allow for proper ventilation and cooling of the unit; do not block any vents in the unit chassis. Also, if rack mounted, remove the rack enclosure front and rear covers and leave empty one full rack space above the unit.
∆
This product should be located away from heat sources such as radiators, heat registers, or other products that produce heat.
∆
This product may be equipped with a polarized plug (one blade wider than the other). This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician to replace your obsolete outlet. Do not defeat the safety purpose of this plug.
∆
Protect the power supply cord from being pinched or abraded.
∆
This product should only be used with a cart or stand that is recommended by the manufacturer.
∆
The power supply cord of this product should be unplugged from the outlet when left unused for a long period of time, or during electrical storms.
∆
This product should be serviced by qualified service personnel when: the power supply cord or the plug has been damaged; or objects have fallen, or liquid has been spilled onto the product; or the product has been exposed to rain; or the product does not appear to operate normally or exhibits a marked change in performance; or the product has been dropped, or the enclosure damaged.
∆
Do not drip nor splash liquids, nor place liquid filled containers on the unit.
∆
CAUTION: No user serviceable parts inside, refer servicing to qualified personnel only.
∆
Fender ® amplifiers and loudspeaker systems are capable of producing very high sound pressure levels which may cause temporary or permanent hearing damage. Use care when setting and adjusting volume levels during use.
3
I n s t r u c c i o n e s I m p o r t a n t e s d e S e g u r i d a d
Este símbolo advierte al usuario de la presencia de niveles peligrosos de voltaje dentro de la carcasa del aparato.
Este símbolo advierte al usuario de que debería leer todos los documentos que acompañan a este aparato para un manejo seguro del mismo.
∆
Lea, conserve y siga lo indicado en las instrucciones. Observe todas las advertencias.
∆
Conecte el cable de corriente solo a una salida de corriente con toma de tierra y cuyo voltaje y frecuencia se correspondan con lo indicado en la etiqueta INPUT POWER que está en el panel trasero de este aparato.
∆
PRECAUCION: Para evitar daños, incendios o descargas eléctricas, no permita que este aparato quede expuesto a la lluvia o la humedad.
∆
Desconecte el cable de corriente cuando vaya a limpiar la superficie exterior de este aparato (use solo un trapo ligeramente húmedo). Antes de volver a conectar el cable de corriente, espere hasta que la unidad esté completamente seca.
∆
Deje un espacio libre de al menos 6 pulgadas (15.24 cm) por detrás de esta unidad para permitir una correcta ventilación y refrigeración de la misma.
∆
Debería situar este aparato lejos de fuentes de calor como radiadores, hornos, calentadores u otros aparatos que produzcan calor.
∆
Este aparato puede que esté equipado con un enchufe polarizado (un borne más ancho que el otro). Esto es una medida de seguridad. Si no lo puede introducir en su salida de corriente, póngase en contacto con un electricista para que le sustituya su salida anticuada. Nunca cambie el enchufe del aparato ya que esto anularía el sistema de seguridad.
∆ Evite que el cable de alimentación pueda quedar aplastado o muy retorcido.
∆
Este producto solo debería ser usado con un soporte o bastidor que haya sido recomendado por el propio fabricante.
∆
Desconecte el cable de alimentación de este aparato de la salida cuando no lo vaya a usar durante un largo tiempo o durante las tormentas eléctricas.
∆
Este aparato debería ser revisado por el servicio técnico oficial cuando: El cable de alimentación o el enchufe se hayan dañado; o se hayan introducido objetos o líquidos dentro del producto; o este aparato haya quedado expuesto a la lluvia; o el producto dé muestras de no funcionar correctamente o se observe un evidente cambio en su rendimiento; o el aparato haya caído al suelo o su carcasa se haya dañado.
∆
No derrame líquidos, ni coloque objetos que los contengan sobre este aparato.
∆ PRECAUCION: Dentro de este aparato no hay piezas susceptibles de ser reparadas por el usuario; dirija cualquier reparación solo al servicio técnico oficial.
∆
Los amplificadores Fender ® son capaces de producir niveles de presión sonora muy elevados que pueden provocar daños temporales o permanentes en el oído. Ajuste los niveles de volumen con cuidado cuando use este aparato.
4
C o n s i g n e s d e S é c u r i t é I m p o r t a n t e s
Ce symbole prévient l’utilisateur de tensions électriques dangereuses présentes dans l’appareil.
Ce symbole conseille à l’utilisateur de lire les instructions fournies pour éviter tout danger d’utilisation du produit.
∆
Lisez, respectez et conservez les instructions. Respectez toutes les mises en garde.
∆
Utilisez uniquement le cordon secteur fourni. Utilisez une connexion secteur pourvue d’une mise à la terre. Veillez à ce que la tension secteur et la fréquence de votre zone géographique correspondent à celles indiquées sous la sérigraphie INPUT
POWER située en face arrière.
∆
ATTENTION : Pour éviter tout dommage, risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.
∆
Déconnectez le cordon de la prise secteur avant de nettoyer l’extérieur de l’appareil (utilisez un tissu humide uniquement).
Attendez que le produit soit complètement sec avant de le replacer sous tension.
∆
Veillez à laisser un vide d’au moins 15 cm derrière l’appareil pour assurer sa ventilation et son refroidissement.
∆
Ce produit doit être éloigné des sources de chaleur comme les radiateurs, ou de toute autre source dégageant de la chaleur.
∆
Si ce produit est équipé d’une borne de terre, veillez à la conserver. Cette borne de terre assure votre protection. Si les prises murales ne sont pas équipées de la terre, contactez un
électricien et faites les changer.
∆
Protégez le cordon secteur pour qu’il ne soit pas pincé ou pour
éviter que les personnes marchent dessus.
∆
Ce produit ne doit être utilisé qu’avec un chariot de transport ou un support préconisé par le fabricant.
∆
Si vous n’utilisez pas ce produit pendant longtemps ou en cas d’orage, débranchez le cordon du secteur.
∆
Ce produit doit être réparé par un personnel qualifié lorsque : Le cordon ou l’embase secteur sont endommagés; Un objet ou un liquide s’est infiltré dans le produit; Le produit a été exposé à la pluie; Le produit ne semble pas fonctionner correctement ou dénote une baisse de performances; Le produit est tombé ou son boîtier a été endommagé
∆
Ne pas projeter de liquides sur le produit. Ne pas poser de récipients contenant un liquide sur l’appareil.
∆ ATTENTION : Ce produit ne contient aucune pièce pouvant être remplacée par l’utilisateur. Les réparations doivent être confiées
à un personnel qualifié uniquement.
∆
Les amplificateurs Fender ® peuvent produire des niveaux sonores très élevés pouvant causer des dommages à votre audition et à celle des tiers. Réglez le volume avec modération.
I s t r u z i o n i I m p o r t a n t i d i S i c u r e z z a
Questo simbolo indica la presenza di tensione pericolosa all'interno della cassa.
Questo simbolo indica l'importanza per l'utilizzatore della lettura di tutta la documentazione allegata al prodotto, finalizzata all'utilizzo sicuro del dispositivo.
∆
Leggere, conservare ed attenersi alle istruzioni, specialmente alle comunicazioni di avvertimento.
∆
Effettuare il collegamento dell'apparecchio ad una presa idonea CA munita di messa a terra e con caratteristiche di tensione e di frequenza corrispondenti ai valori indicati sul retro dell'apparecchio alla voce INPUT POWER.
∆
ATTENZIONE: Non esporre l'apparecchio a pioggia o umidità, al fine di evitare pericoli di danneggiamento, incendio, o scosse elettriche.
∆
Prima di effettuare la pulizia della scatola esterna dell'apparecchio, scollegare il cavo di alimentazione dalla presa (utilizzare solamente un panno umido). Prima di ricollegare l'apparecchio alla presa, assicurarsi che il dispositivo sia completamente asciutto.
∆
Lasciare uno spazio libero dietro all'apparecchio di almeno
15,24 cm per permettere una giusta ventilazione e raffreddamento dell'apparecchio.
∆
Posizionare l'apparecchio lontano da fonti di calore come radiatori, diffusori di aria calda, o comunque altri apparecchi che producono calore.
∆
Per fornire maggiore sicurezza, questo apparecchio può essere dotato di spina polarizzata (uno spinotto piatto più largo dell'altro). Se impossibilitati ad inserirlo nella presa, contattare un elettricista per la sostituzione della vostra presa elettrica.
Non annullare la finalità di sicurezza di questo dispositivo eliminandolo.
∆
Proteggere il cavo di alimentazione al fine di evitare abrasioni, strappi o schiacciamento dello stesso.
∆ Dotare questo apparecchio unicamente di carrello o supporto raccomandati dal produttore.
∆
Nel corso di tempeste elettriche o in caso di prolungati periodi di inattività, scollegare il cavo di alimentazione dalla presa.
∆
La manutenzione dell'apparecchio dovrà essere affidata a tecnici specializzati nei seguenti casi: danneggiamento del cavo di alimentazione, caduta di oggetti o liquidi sull'apparecchio, esposizione dell'apparecchio alla pioggia, funzionamento anomalo dell'apparecchio o con prestazioni alterate, caduta dell'apparecchio o cassa danneggiata.
∆
Proteggere l'apparecchio da schizzi e gocciolamenti e non appoggiare contenitori di liquidi sull'apparecchio stesso.
∆
IMPORTANTE: L'apparecchio non contiene al suo interno dispositivi finalizzati all'utilizzo dello stesso. Affidare la manutenzione unicamente a personale qualificato.
∆
Gli amplificatori Fender ® sono in grado di produrre elevati livelli di pressione acustica (SPL) in grado di causare danni temporanei o permanenti all'udito. Fare quindi attenzione durante la regolazione del livello acustico in fase di utilizzo.
W i c h t i g e S i c h e r h e i t s v o r k e h r u n g e n
Dieses Symbol warnt Sie vor gefährlichen
Spannungen im Innenraum des Gehäuses.
Dieses Symbol fordert Sie zum Lesen der
Begleittexte für einen sicheren Gerätebetrieb auf.
∆
Lesen, befolgen und bewahren Sie alle Anweisungen auf.
Beachten Sie alle Warnungen.
∆
Verbinden Sie das Netzkabel nur mit einer geerdeten
Netzsteckdose entsprechend den Spannungs- und Frequenz-
Nennwerten, die unter INPUT POWER auf der
Produktrückseite angegeben sind.
∆
WARNUNG: Um Beschädigungen, Brände oder Stromschläge zu verhindern, setzen Sie das Gerät weder Regen noch
Feuchtigkeit aus.
∆
Ziehen Sie den Netzstecker, bevor Sie die Geräte-Oberfläche säubern (nur feuchtes Tuch). Warten Sie, bis das Gerät völlig trocken ist, bevor Sie es wieder ans Netz anschließen.
∆
Lassen Sie hinter dem Gerät mindestens 15,24 cm (6”)
Freiraum, um eine ausreichende Belüftung und Kühlung sicherzustellen.
∆
Stellen Sie das Produkt in ausreichender Entfernung von
Wärmequellen, wie Heizkörpern, Wärme-klappen oder anderen Geräten auf, die Hitze erzeugen.
∆
Dieses Produkt ist eventuell mit einem polarisierten Stecker
(unterschiedlich breite Pole) ausgerüstet. Dies ist eine
Sicherheitsfunktion. Wenn der vorhandene Stecker nicht in
Ihre Steckdose passt, lassen Sie die veraltete Steckdose von einem Elektriker ersetzen. Setzen Sie die Sicherheitsfunktion des Steckers nicht außer Kraft.
∆
Das Netzkabel darf nicht geknickt oder abgeschürft werden.
∆
Dieses Produkt sollte nur mit den vom Hersteller empfohlenen
Wagen oder Ständern benutzt werden.
∆ Das Netzkabel des Produkts sollte bei längerem
Nichtgebrauch oder bei Gewittern aus der Netzsteckdose gezogen werden.
∆
Dieses Produkt sollte von qualifiziertem Wartungspersonal gewartet werden, wenn: Netzkabel oder Netzstecker beschädigt wurden oder; Objekte oder Flüssigkeiten ins
Produkt gelangt sind oder; das Produkt dem Regen ausgesetzt war oder; das Produkt nicht normal funktioniert oder sein Betrieb sich deutlich verändert hat oder; das Produkt fallen gelassen wurde oder das Gehäuse beschädigt wurde.
∆
Verschütten Sie keine Flüssigkeiten und stellen Sie keine
Behälter mit Flüssigkeit auf das Gerät.
∆
VORSICHT: Die inneren Bauteile können nur von qualifiziertem Fachpersonal gewartet werden.
∆
Fender ® Verstärker können sehr hohe Schalldruckpegel erzeugen, die zu vorübergehenden oder dauerhaften
Hörschäden führen können. Gehen Sie beim Einstellen der
Pegel vorsichtig vor.
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
1 5 . 2 4 c m
5
6 B u ll ll ll ll e tt tt ® 1 5 0
Your new Bullet
Fender ®
® 150 amplifier delivers world–class tone and world–standard Fender ® DSP technology:
• 15W of output power @ 8 ohms
• Digital Signal Processing
• 15 FX SELECTIONS
• Selectable Normal and Drive channels with independent volume controls
• TREBLE, MIDDLE, and BASS tone controls
• TAPE/CD input jacks enable pre-recorded accompaniment through the amplifier
• HEADPHONES jack for private sessions
Thank you for choosing Fender ®
The W orld’ s most popular instr ument amplifiers—since 1946
P a n e ll ll F u n c tt tt ii ii o n s
A.
INPUT - Plug-in connection for your guitar.
B.
VOLUME - Adjusts the loudness of the Drive channel.
C.
GAIN - Adjusts the distortion level of the Drive channel.
D.
CHANNEL SELECT -
OUT
IN
Drive channel {B–C}
Normal channel {E}
E.
VOLUME - Adjusts the overall loudness of the
Normal channel.
F.
TREBLE / MID / BASS - Adjusts the high–, middle– and low–frequency tone of both channels.
G.
EFFECTS - Selects the active effect (see next page).
H.
TAPE/CD INPUT - Connection for the line–level output from your tape/CD player. Adjust the playback volume at the source. (Stereo inputs are summed together into a mono signal.)
J.
HEADPHONES - Output jack for headphones using a standard 1/4” plug ( or ).
The internal speaker is automatically muted when this jack is used.
J.
POWER SWITCH - Switches the amplifier on / off as indicated by the LED.
Rear Panel
K.
POWER CORD - Connect the power cord in accordance with the voltage and frequency ratings listed on the rear panel of your amplifier.
ww .f
e r .c
m
✧ w ww . m d .
ne
E f f e c t s S e l e c t
Select from 15 variations of 5 effect types. Delay produces various echoes, Reverb creates the acoustic ambience of different spaces or classic
Fender spring Reverb, Chorus and Flange modulate the pitch and delay of a superimposed signal double and Tremolo modulates volume, Select Bypass for no effects.
E ff ff ff ff e c tt tt s
SELECTION
BYPASS
DELAY
REVERB
3
Combination 4
1
2
2
3
CHORUS
Combinations 3
4
FLANGE
TREMOLO
1
2
DESCRIPTION
1 Effects OFF
1 ~150ms (Rockabilly)
~300ms
~500ms
Room
Hall
1
2
1
2
Spring
Reverb + Delay
Fast Sweep
Deep Sweep
Chorus + Delay
Chorus + Reverb
Light Sweep
Deep Sweep
Low Intensity
High Intensity
S p e c ii ii ff ff ii ii c a tt tt ii ii o n s
TYPE:
PART NUMBERS:
POWER REQUIREMENTS:
INPUT IMPEDANCE:
NOMINAL INPUT LEVEL:
POWER OUTPUT:
RATED LOAD IMPEDANCE:
SPEAKER COMPLEMENT:
DIMENSIONS Height:
Width:
Depth:
WEIGHT:
PR 539
2367700933 (120V, 60Hz) USA
2367703933 (240V, 50Hz) AUS
2367705933 (230V, 50Hz) ARG
23677707933 (100V, 50Hz) JPN
38 W
>1M
Ω
90mV
15W R.M.S.
8
Ω
One 8", 8
Ω
, Fender ® Special Design
12.4 in
13.25 in
7.13 in
(31.4 cm)
(33.7 cm)
(18.1 cm)
15 lb (6.8 kg)
Specifications are subject to change without notice
2367701933 (110V, 60Hz) TW
2367704933 (230V, 50Hz) UK
2367706933 (230V, 50Hz) EUR
2367709933 (220V, 60Hz) ROK
7 ww .f
e r .c
m
✧ w ww . m d .
ne
8 B u ll ll ll ll e tt tt ® 1 5 0
Su nuevo amplificador Bullet máxima calidad de Fender ®
® 150 le ofrece el sonido de junto con toda la tecnología
DSP de última generación Fender ® :
• 15 W de potencia de salida @ 8 ohmios
• Procesado digital de señal
• 15 SELECCIONES DE EFECTOS
• Canales Normal y Drive seleccionables con controles de volumen independientes
• Controles de tono TREBLE, MIDDLE y BASS
• Clavijas de entrada TAPE/CD que le permiten pasar música pregrabada a través del amplificador
• Clavijas HEADPHONES para una escucha en privado
Gracias por elegir Fender
Los amplificador
® es de instr umentos más famosos del
F u n c ii ii o n e s d e ll ll P a n e ll ll
A.
INPUT - Conector de entrada para su guitarra.
B.
VOLUME - Ajusta el volumen del canal Drive.
C.
GAIN - Ajusta el nivel de distorsión del canal Drive.
D.
CHANNEL SELECT -
SIN PULSAR Canal Drive o saturado {B–C}
PULSADO Canal Normal {E}
E.
VOLUME - Ajsuta el volumen global del canal
Normal.
F.
TREBLE / MID / BASS - Ajustan el tono de las frecuencias agudas, medias y graves de ambos canales.
G.
EFFECTS - Le permiten elegir el efecto activo (vea la página siguiente).
H.
TAPE/CD INPUT - Conexión para la salida de nivel de línea de su reproductor de CD/cinta.
Ajuste el volumen de la reproducción en la fuente. (Las entradas stereo son sumadas juntas en una señal mono).
J.
HEADPHONES - Clavija de salida para auriculares que usen un conector standard de 6,3 mm
( o ). El altavoz interno queda anulado automáticamente cuando use esta salida.
J.
INTERRUPTOR POWER - Enciende o apaga el amplificador, tal como le indica el LED.
Panel trasero
K.
CABLE DE CORRIENTE - Conecte el cable de corriente de acuerdo con los valores de voltaje y frecuencia que están indicados en el panel trasero de la unidad.
ww .f
e r .c
m
✧ w ww . m d .
ne
Elija entre 15 variaciones de 5 tipos de efectos.
Delay produce distintos tipos de ecos, Reverb crea la ambientación acústica de distintos espacios o de una clásica reverb de muelles de Fender, Chorus y
Flange modulan el tono y el retardo de una señal duplicada superpuesta y Tremolo modula el volumen. Elija Bypass si no quiere efectos.
E ff ff e c tt tt o s
SELECCION
BYPASS 1
DESCRIPCION
Efectos OFF
1 ~150 ms (Rockabilly)
DELAY (retardo) 2 ~300 ms
REVERB
Combinación 4
1
CHORUS
2
Combinaciones 3
2
3
3
1
~500 ms
Habitación
Sala
Muelles
Reverb + Retardo
Barrido rápido
Barrido profundo
Chorus + Retardo
FLANGE
TREMOLO
2
1
4
1
2
Chorus + Reverb
Barrido suave
Barrido profundo
Baja intensidad
Intensidad alta
E s p e c ii ii ff ff ii ii c a c ii ii o n e s tt tt é c n ii ii c a s
TIPO:
REFERENCIAS:
POTENCIA:
IMPEDANCIA DE ENTRADA:
NIVEL DE ENTRADA NOMINAL:
POTENCIA DE SALIDA:
IMPEDANCIA DE CARGA MEDIA:
ALTAVOZ:
DIMENSIONES Altura:
Anchura:
Profundidad:
PESO:
PR 539
2367700933 (120V, 60Hz) USA
2367703933 (240V, 50Hz) AUS
2367705933 (230V, 50Hz) ARG
23677707933 (100V, 50Hz) JPN
38 W
>1 M
Ω
90 mV
15 W R.M.S.
8
Ω
Uno de 8", 8
Ω
, con diseño especial Fender ®
12.4 pulgadas
13.25 pulgadas
7.13 pulgadas
(31.4 cm)
(33.7 cm)
(18.1 cm)
15 libras (6.8 kg)
2367701933 (110V, 60Hz) TW
2367704933 (230V, 50Hz) UK
2367706933 (230V, 50Hz) EUR
2367709933 (220V, 60Hz) ROK
Las especificaciones están sujetas a cambios sin previo aviso
9 ww .f
e r .c
m
✧ w ww . m d .
ne
10 B u ll ll ll ll e tt tt ® 1 5 0
Le Bullet ® 150 vous offre le célèbre son Fender ®
également équipé des technologies DSP Fender ®
. Il est
:
• Puissance de 15 W dans 8 Ohms
• Traitement numérique du signal par DSP :
• 15 Effets
• Sélection des canaux Normal et Drive avec réglages séparés de volume
• Réglages de tonalité TREBLE, MIDDLE et BASS
• Entrées TAPE/CD permettant de jouer sur un accompagnement
• Jack pour casque HEADPHONES avec coupure du haut-parleur interne
Mer ci d’avoir choisi Fender ®
F o n c tt tt ii ii o n s e tt tt rr é g ll ll a g e s
A.
INPUT - Permet la connexion du cordon guitare.
B.
VOLUME - Niveau du canal Drive.
C.
GAIN - Détermine le taux de distorsion du canal
Drive.
D.
SÉLECTION DE CANAL -
RELÂCHÉ
ENFONCÉ
Canal Drive {B–C}
Canaux Normal {E}
E.
VOLUME - Règle le volume général du canal
Normal.
F.
TREBLE / MID / BASS - Règle les graves, médiums, aigus, des deux canaux.
G.
EFFECTS SELECT - Sélectionne l’effet (page suivante).
H.
ENTRÉE TAPE/CD - Permet la connexion d’un lecteur de CD/Cassette à niveau ligne. Réglez le niveau de lecture sur la platine source (les signaux stéréo sont mélangés en mono).
J.
HEADPHONES - Embase de connexion de casque au format Jack 6,35 mm ( ou ). Le haut-parleur interne est coupé lors de la connexion du casque.
J.
INTERRUPTEUR SECTEUR- Permet de placer l’amplificateur sous/hors tension (la mise sous tension est indiquée par la Led allumée).
Face arrière
K.
CORDON SECTEUR - Connectez le cordon secteur et vérifiez que la tension et la fréquence indiquées sur l’amplificateur correspondent à celles de votre pays. ww .f
e r .c
m
✧ w ww . m d .
ne
E ff ff ff ff e tt tt s
S é l e c t i o n d e s e f f e t s
Vous permet de sélectionner l’un des 15 effets parmi 5 types. Le Delay produit des répétitions, l’effet Reverb simule des espaces acoustiques ambience divers ou la réverbération à ressorts
Fender, les effets Chorus et Flange modulent la hauteur et le retard d’un signal ajouté au signal d’entrée et l’effet Tremolo module le volume.
Sélectionnez Bypass pour annuler les effets.
SÉLECTION
BYPASS
DELAY
REVERB
Combinaison 4
1
CHORUS
2
Combinaisons 3
2
3
3
1
1
DESCRIPTION
Effets désactivés
1 ~150 ms (Rockabilly)
2 ~300 ms
~500 ms
Room
Hall
Ressorts
Reverb + Delay
Balayage rapide
Balayage important
Chorus + Delay
FLANGE
TREMOLO
2
1
4
1
2
Chorus + Reverb
Balayage léger
Balayage important
Faible intensité
Forte intensité
C a rr a c tt tt é rr ii ii s tt tt ii ii q u e s tt tt e c h n ii ii q u e s
TYPE :
RÉFÉRENCE :
CONSOMMATION ÉLECTRIQUE :
IMPÉDANCE D’ENTRÉE :
NIVEAU D’ENTRÉE NOMINAL :
PUISSANCE DE SORTIE :
IMPÉDANCE DE CHARGE :
HAUT-PARLEUR INTERNE
DIMENSIONS Hauteur :
Largeur :
Profondeur :
POIDS:
PR 539
2367700933 (120 V, 60 Hz) USA
2367703933 (240 V, 50 Hz) AUS
2367705933 (230 V, 50 Hz) ARG
23677707933 (100 V, 50 Hz) JPN
2367701933 (110 V, 60 Hz) TW
2367704933 (230 V, 50 Hz) UK
2367706933 (230 V, 50 Hz) EUR
2367709933 (220 V, 60 Hz) ROK
38 W
>1 M
Ω
90 mV
15 W efficace
8
Ω
Un haut-parleur Fender ® de 8 pouces, 8
Ω
, de conception spéciale
31,4 cm
33,7 cm
18,1 cm
6,8 kg
Caractéristiques sujettes à modifications sans préavis.
11 ww .f
e r .c
m
✧ w ww . m d .
ne
12 B u ll ll ll ll e tt tt ® 1 5 0
Il nuovo amplificatore Bullet ® rinomata tecnologia DSP Fender ®
150 è dotato della e offre tutta la qualità del classico suono Fender ® :
• Potenza in uscita da 15W @ 8 ohms
• Processamento digitale del segnale
• 15 DIVERSE SELEZIONI D’EFFETTO
• Canali Normal e Drive selezionabili con controlli di volume indipendenti
• Controlli di tono TREBLE, MIDDLE e BASS
• Gli ingressi jack TAPE/CD permettono di amplificare il segnale audio proveniente da lettori CD o nastro.
• La connessione HEADPHONES permette di poter suonare in cuffia senza disturbare nessuno.
Grazie per aver scelto Fender ®
Gli amplificatori per str umenti più famosi al mondo—dal 1946
F u n z ii ii o n ii ii d e ll ll P a n n e ll ll ll ll o F rr o n tt tt a ll ll e
A.
INPUT - Connessione per la tua chitarra.
B.
VOLUME - Regola il Loudness del canale Drive.
C.
GAIN - Regola il livello di distorsione del canale
Drive.
D.
SELEZIONE DEL CANALE -
OUT
IN
Canale Drive {B–C}
Canale Normal {E}
E.
VOLUME - Regolazione del Loudness generale del canale Normal.
F.
TREBLE / MID / BASS - Controlli per la regolazione delle frequenze alte (Treble), medie
(Mid) e basse (Bass) di entrambi i canali.
G.
EFFECTS - Consente la selezione degli effetti
(consulta la pagina seguente).
H.
TAPE/CD INPUT - Ingressi per la connessione delle uscite di linea di lettori CD o Tape. Il volume d’esecuzione dev’essere regolato dall’apparecchiatura sorgente (i segnali stereo verranno sommati in un unico segnale mono).
J.
HEADPHONES - Uscita per il collegamento di cuffie dotate di connettore jack standard da 1/4”
( oppure ). Collegando una cuffia a questo connettore, l’altoparlante interno verrà silenziato automaticamente.
J.
INTERRUTTORE POWER - Attiva/disattiva l’amplificatore (status segnalato dall’indicatore
LED).
Pannello Posteriore
K.
CAVO D’ALIMENTAZIONE - Collega ilcavo d'alimentazione in dotazione ad una presa collegata a terra e conforme alle specifiche di tensione e frequenza riportate sul pannello posteriore del tuo amplificatore.
ww .f
e r .c
m
✧ w ww . m d .
ne
E ff ff ff ff e tt tt tt tt ii ii
S e l e z i o n e d e g l i e f f e t t i
È possibile selezionare 15 variazioni di 5 diversi tipi d’effetti. Il Delay genera vari tipi di effetti eco; il
Reverb riproduce l’ambiente acustico di diverse dimensioni, oppure il classico riverbero a molle
Fender; Chorus e Flange permettono la modulazione del Pitch e del Delay di un segnale sovrapposto; il Tremolo modula il volume.
Seleziona Bypass per non generare alcun effetto.
SELEZIONE
BYPASS
DELAY
REVERB
Combinazione 4
1
CHORUS
2
Combinazione 3
2
3
3
1
1
DESCRIZIONE
Effetto disabilitato
1 ~150ms (Rockabilly)
2 ~300ms
~500ms
Room
Hall
Spring
Reverb + Delay
Fast Sweep
Deep Sweep
Chorus + Delay
FLANGE
TREMOLO
2
1
4
1
2
Chorus + Reverb
Light Sweep
Deep Sweep
Low Intensity
High Intensity
S p e c ii ii ff ff ii ii c h e
TIPO:
NUMERO PARTI:
CONSUMO ENERGETICO:
IMPEDENZA IN INGRESSO:
LIVELLO D’INGRESSO NOMINALE:
POTENZA IN USCITA:
IMPEDENZA DI CARICO:
ALTOPARLANTE:
DIMENSIONI Altezza:
Larghezza:
Profondità:
PESO:
PR 539
2367700933 (120V, 60Hz) USA
2367703933 (240V, 50Hz) AUS
2367705933 (230V, 50Hz) ARG
23677707933 (100V, 50Hz) JPN
38 W
>1M
Ω
90mV
15W R.M.S.
8
Ω
Un altoparlante Fender ® Special Design da 8", 8
Ω
31.4 cm
33.7 cm
18.1 cm
(12.4 in)
(13.25 in)
(7.13 in)
6.8 kg (15 lb)
2367701933 (110V, 60Hz) TW
2367704933 (230V, 50Hz) UK
2367706933 (230V, 50Hz) EUR
2367709933 (220V, 60Hz) ROK
Le specifiche possono essere soggette a variazioni senza alcun preavviso.
13 ww .f
e r .c
m
✧ w ww . m d .
ne
14 B u ll ll ll ll e tt tt ® 1 5 0
Ihr neuer Bullet ® 150 Amp liefert Weltklasse Fender ®
Sounds und Weltstandard Fender ® DSP Technologie:
• 15 W Ausgangsleistung @ 8 Ohm
• Digitale Signalbearbeitung
• 15 FX OPTIONEN
• Wählbare Normal- und Drive-Kanäle mit unabhängigen Lautstärke-Reglern
• TREBLE-, MIDDLE- und BASS-Klangregler
• TAPE/CD Eingangsbuchsen zum Abspielen voraufgezeichneter Begleitungen über den Amp
• HEADPHONES-Buchse für störungsfreie Sessions
Danke für die W ahl eines Fender ® Pr odukts
Die beliebtesten Instr umentenverstärker der W elt —
V o rr d e rr s e ii ii tt tt ii ii g e F u n k tt tt ii ii o n e n
A.
INPUT - Anschluss für Ihre Gitarre.
B.
VOLUME - Regelt den Pegel des Drive-Kanals.
C.
GAIN - Regelt den Distortion-Pegel des Drive-
Kanals.
D.
CHANNEL SELECT -
IN Normal-Kanal {E}
E.
VOLUME - Regelt den Gesamtpegel des Normal-
Kanals.
F.
TREBLE / MID / BASS - Regelt die Höhen, Mitten und Bässe beider Kanäle.
G.
EFFECTS - Wählt den aktiven Effekt (siehe nächste
Seite).
H.
TAPE/CD INPUT - Anschluss für ein Line-Pegel
Ausgangssignal eines Tape/CD Players. Regeln
Sie den Wiedergabepegel an der Quelle. (Stereo-
Eingänge werden zu einem Mono-Signal summiert.)
J.
HEADPHONES - Ausgangsbuchse für Kopfhörer mit standard 1/4” Stecker ( oder ).
Ist diese Buchse belegt, werden die internen
Lautsprecher automatisch stummgeschaltet.
J.
POWER-SCHALTER - Schaltet den Amp ein/aus, was durch die LED angezeigt wird.
Rückseite
K.
POWER CORD - Schließen Sie hier das Netzkabel entsprechend den
Spannungs- und Frequenznennwerten an, die auf der Rückseite des Amps angegeben sind.
ww .f
e r .c
m
✧ w ww . m d .
ne
E ff ff ff ff e k tt tt e
E f f e k t w a h l
Wählt 15 Variationen von 5 Effekttypen. Delay
erzeugt verschiedene Echos, Reverb simuliert die
Akustik verschiedener Räume oder des klassischen
Fender Federhalls, Chorus und Flange modulieren die Tonhöhe und Verzögerung einer überlagerten
Signalkopie, Tremolo variiert den Pegel und Bypass umgeht alle Effekte.
OPTION
BYPASS
DELAY
REVERB
Combination 4
1
CHORUS
2
Combinations 3
2
3
3
1
1
BESCHREIBUNG
Effekte AUS
1 ~150ms (Rockabilly)
2 ~300ms
~500ms
Room
Hall
Spring
Reverb + Delay
Fast Sweep
Deep Sweep
Chorus + Delay
FLANGE
TREMOLO
2
1
4
1
2
Chorus + Reverb
Light Sweep
Deep Sweep
Low Intensity
High Intensity
TYP:
TEILENUMMERN:
LEISTUNGSAUFNAHME:
EINGANGSIMPEDANZ:
NOMINAL-EINGANGSPEGEL:
AUSGANGSLEISTUNG:
NOMINAL-LASTIMPEDANZ:
LAUTSPRECHER-BESTÜCKUNG:
ABMESSUNGEN Höhe:
Breite:
Tiefe:
GEWICHT:
PR 539
2367700933 (120V, 60Hz) USA
2367703933 (240V, 50Hz) AUS
2367705933 (230V, 50Hz) ARG
23677707933 (100V, 50Hz) JPN
38 W
>1M Ohm
90 mV
15 W R.M.S.
8 Ohm eine 8", 8 Ohm, Fender ® Spezialkonstruktion
31,4 cm
33,7 cm
18.1 cm
6.8 kg
(12.4 in)
(13.25 in)
(7.13 in)
(15 lbs)
T e c h n ii ii s c h e D a tt tt e n
2367701933 (110V, 60Hz) TW
2367704933 (230V, 50Hz) UK
2367706933 (230V, 50Hz) EUR
2367709933 (220V, 60Hz) ROK
Technische Daten können ohne Vorankündigung geändert werden.
15 ww .f
e r .c
m
✧ w ww . m d .
ne
16 B u ll ll ll ll e tt tt ® 1 5 0 ww .f
e r .c
m
✧ w ww . m d .
ne
17 ww .f
e r .c
m
✧ w ww . m d .
ne
18 ww .f
e r .c
m
✧ w ww . m d .
ne
19 ww .f
e r .c
m
✧ w ww . m d .
ne
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA USA
Bullet ® and Fender ® are registered trademarks of FMIC.
Other trademarks are property of their respective owners.
Copyright © 2004 FMIC P/N 064824 REV A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project