LUMEL P20H TYPE Transducer User’s Manual

PROGRAMMABLE
TRANSDUCER
OF DC CURRENT AND
DC VOLTAGE SIGNALS
P20H TYPE
USER’S MANUAL
Contents:
1. APPLICATION . ............................................................................5
2. TRANSDUCER SET .....................................................................5
3. OPERATIONAL SAFETY . ...........................................................6
4. INSTALLATION . ..........................................................................7
4.1.Fixing Way .............................................................................7
4.2.External Connection Diagrams ..............................................7
5. SERVICE ......................................................................................9
5.1. Transducer Configuration by Means of the LPCon Program.....10
5.2.Register Map (in option with RS-485 Interface) . .................10
5.3.Manufacturer’s Parameters . ................................................14
6. TECHNICAL DATA ....................................................................15
7. ORDERING CODES ...................................................................18
8. MAINTENANCE AND GUARANTEE . .......................................19
1. APPLICATION
Transducers of P20H series are applied for the continuous conversion
of one quantity: high voltage or high current signal, uni or bipolar signal
into a standard d.c. current or d.c. voltage signals, or into a digital form
available through the RS-interface.
The transducer is configurable through the PD14 programmer. With the
aid of the programmer and the LPCon program, one can reprogram
following parameters:
- measurement averaging time,
- conversion characteristic,
- preservation of the output signal at overflows,
- narrowing of the output signal,
- RS485 transmission parameters,
The transducer has a galvanic separation between individual blocks:
- supply
- measuring inputs
- outputs and PD14 programmer
2. TRANSDUCER SET
The transducer set is composed of:
- P20H transducer............................................. 1 pc
- user’s manual.................................................. 1 pc
- guarantee card............................................... 1 pc
- protection plug of the programmer socket..... 1 pc
When unpacking the transducer, please check whether the type and
execution code on the data plate correspond to the order.
3. BASIC REQUIREMENTS, OPERATIONAL
SAFETY
In the safety service scope, the transducer meets the requirements of
the EN 61010-1 standard.
Observations concerning the operational safety:
· All operations concerning transport, installation, and commissioning
as well as maintenance, must be carried out by qualified, skilled personnel, and national regulations for the prevention of accidents must be observed.
· The programming of P20H transducer parameters must be carried out after disconnecting measuring circuits.
· Before switching the transducer on, one must check the correctness of connections to the network.
· Do not connect the transducer to the network through an autotransformer.
· Before removing the transducer housing, one must switch the supply off and disconnect measuring circuits. The removal of the transducer housing during the guarantee contract period may cause its cancellation.
· The transducer is destined to be installed and used in electromagnetic industrial environment conditions.
· When connecting the supply, one must remember that a switch or a circuit-breaker should be installed in the building. This switch should be located near the device, easy accessible by the operator, and suitably marked as an element switching the meter off.
· Non-authorized removal of the housing, inappropriate use, incorrect
installation or operation, create the risk of injury to personnel or transducer damage.
For more detailed information, please study the User’s Manual.
4. INSTALLATION
4.1. Fixing Way
P20H transducers are destined to be fixed on a 35 mm rail acc. to EN 60715 standard.
Overall dimensions and the fixing way are presented on the fig. 1.
Fig. 1. Overall dimensions and fixing way of the P20H transducer
4.2. External Connection Diagrams
The transducer has a separable strip with screw terminals, which enable the connection of supply and output by 2.5 mm2 cross-section
external wires. The connection of input signals must be carried out
to inseparable screw terminals with wires of maximal 1.5 mm2 crosssection.
Fig. 2. Electrical connections of P20H transducer inputs.
a) voltage
b) current
Fig. 3. Electrical connections of the P20U transducer
supply and output:
a) with analog output,
b) with RS-485 interface
5. SERVICE
After switching the transducer on, the work state diode should light in
red for a moment, next it should light in green.
Diode of the transducer work state:
- the state diode lights in green – normal work,
- the state diode lights in red – improper work
parameters; one must configure the transducer
again,
- the state diode pulsates in red – lack of calibration
or the non-volatile memory is damaged; one must
return the transducer to the manufacturer.
Diodes only in the option with RS-485 interface:
- the RxD diode lights – reception of data,
- the TxD diode lights – transmission of data.
Fig. 4. View of the P20H transducer
The write confirmation in registers is signaled by a short extinction of the
state diode. Till the time to obtain the required number of correct measurements (acc. to the table 1), the arithmetical mean value of measurements which have been doing so far, is converted. The measurement
of values beyond the measuring range causes the overflow setting and
begins the counting of correct measurements from the beginning. The
measurement is carried out on the mowing window principle. The time
is set up on 1 s by the manufacturer.
When the averaging time is less than 10 sec – the single measurement lasts
ca 30 ms however, above 10 sec, the measurement lasts ca 0.5 sec.
Table 1
Averaging time
Number of averaged
measurements
0.2s 0.4s 0.6s 0.8s
6
13
20
27
1s
34
3s
5s
103 172
10s 15s
20s
20
40
30
In the transducer , one can program the behaviour of the analog output
(the recording of the output value in the option with RS-485) at overflows of the set up input measuring range.
Set up values: expected on the output at lower overflow (Out-d) for a
value below the lower input overflow (In-d) and the expected value on
the output at upper overflow (Out-u) for values above the upper input
overflow (In-u) – Values are presented in the table 3.
5.1. Transducer Configuration by Means of the
LPCon Program
The free delivered LPCon program, available in our www.lumel.com.pl
page, is destined for the P20H transducer configuration. The detailed
description of parameter configuration is presented in a separate user’s
manual for programming (instruction for transducer configuration by means of the LPCon program). In the option with RS-485 interface, the transducer can be configured directly through the interface. When configuring
the transducer through the PD14 programmer, one must turn the RS-485
interface off.
5.2. Register Map (in option with RS-485 Interface)
Table 2
Register Operaaddress tion
Range
Description
Averaging time: 0 – 0,2 s; 1 – 0,4 s; 2- 0,6 s; 3 – 0,8 s; 4 – 1 s; 5 - 3 s; 6 - 5 s; 7 - 10 s; 8 - 15 s; 9 - 20 s;
4000
RW
0...9
4001
RW
0...2
4002
RW
0, 1
4003
RW
1...247
Address in MODBUS network
4004
RW
0...3
Transmission mode: 0->8n2, 1->8e1,2->8o1, 3->8n1
10
Continuous output:
0 - normaln work,
1 - value from the register 7602,
2- value from the register 7603
Continuous output – overflow service: 0 – switched off, 1 – service
4005
RW
4006
RW
0, 1
4007
R
0...65535
Baud rate: 0->4800, 1->9600, 2->19200
Change parameters of the MODBUS transmission: 1 - change
Status
4008
R
0
Reserved
4009
R
0...65535
Reserved
4010
R
0...65535
Reserved
4011
R
0...65535
Program version
0...2
Reserved
Reserved
X
X
X
X
X
X
X
X
14
13
12
11
10
9
8
7
Transducer output code
Reserved
X
bity 15
Transducer input code
Reserved
Reserved
Averaging state
Range overflow
Non-calibrated transducer
Error of transducer
parameter values
Opis rejestru status
XXXX
6
5
4
XXX
3
MSB
2
1
0
LSB
Bit – 15 Non-calibrated transducer
0 – measuring input of the calibrated transducer
1 – signaling of transducer input calibration lack
Bit – 14 Error of transducer parameter values
0 – correct transducer parameters
1 – signaling of an incorrect transducer parameter readout
Bit – 13 Signaling of an upper range overflow
0 – normal work
1 – range overflow
11
Bit – 12 Averaging state
0 – a full interval of the measurement averaging time was elapsed
1 – a full interval of the measurement averaging time was not elapsed
Bit - 11 – 7 Reserved
Bit 6
Bit 5
Bit 4
Bit 3
Bit-6 – 3 measuring inputs
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
Meaning
reserved
-/+ 100 V d.c.
-/+ 250 V d.c.
-/+ 400 V d.c.
-/+ 1 A d.c.
-/+ 5 A d.c.
0...100 V d.c.
0...250 V d.c.
0...400 V d.c.
Bit 2
Bit 1
Bit 0
Bit - 2 – 0 Output
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
12
Meaning
reserved
current output 0(4)...20 mA
current output 0(4)...20 mA
voltage output 0...10 V
RS-485
Table 3
Register Register
Opera2x16 bit 32 bit
tions
address address
Description
7200
7600
RW
Continuous output – lower input value (x1)
7202
7601
RW
Continuous output – upper input value (x2)
7204
7602
RW
Continuous output – lower output value (y1)
7206
7603
RW
Continuous output – upper output value (y2)
7208
7604
RW
Minimal input value
7210
7605
RW
Maximal input value
7212
7606
RW
Expected value on the output at lower overflow
Out-d
7214
7607
RW
Expected value on the output at upper overflow
Out-u
7216
7608
R
7218
7609
R
Measured value
7220
7610
R
Output value
Measured value taking into consideration
registers 7604 and 7605
Reg. 7608 = reg. 7604 if reg. 7609 £ reg. 7604
Reg. 7608 = reg. 7605 if reg. 7609 ³ reg. 7605
13
5.3. Manufacturer’s parameters
Table 4
Parameter description
Averaging time
Continuous output: working mode
Range / Value
0.2 s; 0.4 s; 0.6 s; 0.8 s; 1 s; 3 s; 5 s; 10 s; 15 s; 20 s;
Normal work, output
minimum, output
maximum
Manufacturer’s
value *
1s
Normal work
-999999...999999
x1 = 0 or –Un or –In ;
x2 = Un or In,
y1 = 0 or –Un or –In or 4;
y2 = 10 or 20
off, on
turned off **
Lower input overflow
-999999...999999
0 or –Un or –In **
Upper input overflow
-999999...999999
Un or In **
Lower output overflow
-999999...999999
0, 3,9 **
Upper output overflow
-999999...999999
11 V or 22 mA
Continuous output: transition characteristic:
(x1, y1) à (x2, y2)
Continuous output: overflow
service
1...247
1
Transmission mode ***
8n2, 8e1, 8o1, 8n1,
8n2
Baud rate ***
4800, 9600, 19200
9600
Address in Modus network ***
* - Depending on option
** - In the 4...20 mA option, the overflow service is switched on, the minimal
output value is set on 3.9 mA, the minimal input value is converted according
to the transition characteristic.
*** - Only in the option with RS-485 output
14
6. TECHNICAL DATA
Measuring Ranges
INPUTS:
Measuring range of the unipolar Un voltage:
- 0.5...0...100...130 V d.c.
-1...0...250...325 V d.c.
input resistance > 2 MW
- 2...0...400...630 V d.c.
Measuring range of the bipolar Un voltage:
-130...-100...100...130 V d.c.
- 325...- 250...250...325 V d.c. input resistance > 2 MW
- 630...- 400...400...630 V d.c.
Measuring range of the bipolar In current:
-1.3...-1.0...1.0...1.3 A d.c.
input resistance 10 mW ±10%
- 6.3...- 5...5...6.3 A d.c. input resistance 2 mW ±10%
Analog output
current 0(4)...20...22 mA
load resistance £ 500 W
voltage 0...10...11 V
load resistance  500 W
resolution 0.01% of the range
output reaction time: 200 ms
Serial interface
RS-485: address 1...247
mode: 8N2, 8E1, 8O1, 8N1
baud rate: 4.8, 9.6, 19.2 kbit/s
transmission protocol: Modbus RTU
response time: 200 ms
Basic conversion error
±0.2% of the range
15
Additional errors in rated operating conditions:
- from ambient temperature changes
(50% of the intrinsic error/10 K)
Sustained overload:
Short duration overload (1 s)
150% Un (in. 400 V, ± 400 V),
120% Un (other in.),
120% In
voltage input 2 Un (<1000 V)
current input 10 In
Rated operating conditions:
- supply voltage - ambient temperature
- storage temperature
- humidity - work position
85...253 V a.c. (45...65 Hz ) or d.c.
20...40 V a.c. (45...65 Hz ) or d.c.
-20...23...60°C
-25...+85°C
< 95% (inadmissible vapour condensation)
any
Averaging time
(programmable):
³ 0,2 s (default 1 s)
Preheating time
15 minutes
Galvanic isolation between:
- supply – measuring input
- supply – output
- measuring input – output
3.2 kV d.c.
2 kV d.c.
3.2 kV d.c.
Ensured protection grade
acc. to EN 60529:
- casing
- from the terminal side
IP 40
IP 20
Overall dimensions
22.5 x 100 x 120 mm
Weight 0.125 kg
16
Fixing
on a 35 mm rail acc. EN 60715
Input power
< 3 VA
Electromagnetic compatibility:
– noise immunity acc. to EN 61000-6-2
– noise emissions acc. to EN 61000-6-4
Safety requirements acc. to EN 61010 -1 standard:
– isolation between circuits: basic
– installation category: III ( for the 400 V option – category II)
– pollution grade: 2
– maximal phase-to-earth working voltage:
- for the supply circuit: 300 V
- for the measuring input: 600 V - category II, (300 V – cat. III)
- for the programming input: 50 V
- for output: 50 V
– altitude above sea level < 2000 m.
17
7. ORDERING CODES
TRANSDUCER
Table 5.
P20H -
X
X
X XX X
X
Input signal:
+/- 100 V d.c.............................................. 1
+/- 250 V d.c.............................................. 2
+/- 400 V d.c.............................................. 3
+/- 1 A d.c.................................................. 4
+/- 5 A d.c.................................................. 5
0...100 V d.c.............................................. 6
0...250 V d.c.............................................. 7
0...400 V d.c.............................................. 8
Output:
0...20 mA........................................................... 1
4...20 mA........................................................... 2
0...10 V.............................................................. 3
RS-485.............................................................. 4
Supply:
85...253 V a.c./d.c.....................................................1
20...40 V a.c./d.c.......................................................2
Version:
standard ......................................................................... 00
non-standard settings......................................................NS
custom-made*................................................................. XX
Language:
Polish.......................................................................................P
English.....................................................................................E
other*........................................................................................X
Acceptance Tests
without extra quality requirements...................................................0
with an extra quality inspection certificate........................................1
acc. to customer’s requirements*.................................................... X
* after agreeing with the Manufacturer
18
Example of Order:
The code: P20H - 6 1 1 00 E 0 means:
P20H – transducer of d.c. current and d.c. voltage signals,
6 – input signal: 0...100 V d.c.,
1 – output: 0...20 mA,
1 – supply: 85...253 V a.c./d.c.,
00 – standard version
E – English language
0– without extra quality inspection requirements
8. MAINTENANCE AND GUARANTEE
The P20H separator does not require any periodical maintenance.
In case of some incorrect operations:
From the Shipping During the Period Given in the Annexed
Guarantee Card:
One should return the separator to the Manufacturer’s Quality
Inspection Dept.
If the instrument has been used in compliance with the instructions,
we guarantee to repair it free of charge.
The disassembling of the casing may cause the cancellation of the
granted guarantee.
After the Guarantee Period:
One should turn over the separator to repair it in a certified service
workshop.
Spare parts are available for the period of five years from the date
of purchase.
Our policy is one of continuous improvement and we reserve
the right to make changes in design and specifications of
any products as engineering advances or necessity requires
and revise the above specifications without notice.
19
SALES PROGRAM
MEASUREMENT
CONTROL
RECORDING
ANALYSIS
n DIGITAL AND BARGRAPH PANEL METERS
n MEASURING TRANSDUCERS
n ANALOG PANEL METERS (DIN INSTRUMENTS)
n PROCESS AND POWER CONTROLLERS
n CHART AND PAPERLESS RECORDERS
n 1-PHASE AND 3-PHASE WATT-HOUR METERS
n NUMERICAL AND ALPHANUMERICAL LARGE SIZE DISPLAYS
n ACCESSORIES FOR MEASURING INSTRUMENTS (SHUNTS AND
MODULES)
n MEASURING SYSTEMS (LUMEL-PROCESS)
n CUSTOM-MADE ELECTRONIC SUB-ASSEMBLIES ACC. TO ORDERS
WE ALSO OFFER OUR SERVICES IN THE PRODUCTION OF:
n ALUMINIUM ALLOY PRESSURE CASTINGS
n PRECISION ENGINEERING AND THERMOPLASTICS PARTS
n PRESSURE CASTING DIES AND OTHER TOOLS
n CUSTOM-MADE ELECTRONIC SUB-ASSEMBLIES
QUALITY PROCEDURES:
According TO ISO 9001 AND ISO 14001 international requirements.
ALL OUR INSTRUMENTS HAVE CE MARK.
FOR MORE INFORMATION, PLEASE WRITE TO OR PHONE OUR EXPORT DEPARTMENT
P20H-07/1 17.01.2011
Lubuskie Zak³ady Aparatów Elektrycznych LUMEL S.A.
ul. Sulechowska 1
65-022 Zielona Góra - Poland
Tel.: (48-68) 329 51 00 (exchange)
Fax: (48-68) 329 51 01
e-mail: [email protected]
http://www.lumel.com.pl
20
Export Department:
Tel.: (48-68) 329 53 02 or 53 04
Fax: (48-68) 325 40 91
e-mail: [email protected]
">