Clarion WXZ468RMP Service manual

PDF Download

Document

Clarion Co., Ltd.

50 Kamitoda, Toda-shi, Saitama 335-8511 Japan

Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan

Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703

Published by Service Dept.

298-6340-00 Feb.2006

Printed in Japan

Service Manual

2-DIN 6-disc

CD/MP3/WMA Receiver

/ CeNET Control

Model

(PE-2758E)

This product is a lead free model.

Lead free solder is used in PWB stamped LF mark.

Please keep the following conditions when you repair.

1. Use lead free solder.

* Koki's lead free solder S3X-55M 0.6mm

(CLARION Parts No.642-0231-01)

* Koki's lead free solder S3X-55M 1.0mm

(CLARION Parts No.642-0231-02)

2. Use a nitrogen solder system.

3. Do not use "General solder" and "Lead free solder" together.

NOTES

* As for this model, CCC-TUNER is used.

When you exchange it due to the tuner pack (BL1:880-

2150A) trouble, it is necessary to adjust for S-meter etc.

Special JIG is necessary for an accurate adjustment.

The procedure document for the exclusive use jig is appended to it.

* Use only compact discs bearing the or mark.

* Some CDs recorded in CD-R/CD-RW mode may not be usable.

* This product includes technology owned by Microsoft

Corporation and cannot be used or distributed without a license from MSLGP.

* and logo are trademarks or registered trademarks of Microsoft Corporation in the

United States and/or other countries.

* We cannot supply PWB with component parts in principle. When a circuit on PWB has failure, please repair it by component parts base. Parts which are not mentioned in service manual are not supplied.

* Specifications and design are subject to change without notice for further improvement.

- 1 -

SPECIFICATIONS

Radio section

Tuning system:

Receive range:

PLL frequency synthesizer system

FM 87.5MHz to 108MHz

(0.05MHz steps)

MW 531kHz to 1,602kHz

(9kHz steps)

LW 153kHz to 279kHz

(3kHz steps)

CD player section

System:

Usable discs:

Compact disc digital audio system

Compact disc

Frequency response: 10Hz to 20kHz(+/-1dB)

Signal to noise ratio: 90dB(1kHz)

Dynamic range: 90dB(1kHz)

Harmonic distortion: 0.01%

Channel separation: 75dB(1kHz)

MP3/WMA mode: MP3 ; Sampling rate 11.025kHz -

48kHz

Bit rate : 8kbps - 320kbps / VBR

WMA;Bit rate;48kbps-192kbps/VBR

Logical format(File system);

ISO9660 level 1, 2 or JOLIET or

Romeo

Audio amplifier section

Output power: 27W x 4ch (DIN 45324, +B=14.4V)

Continuous average power output:

17W x 4ch

(4 ohm, 20Hz to 20kHz, 1%THD)

Bass control action: +14dB, -12dB(60Hz/80Hz/120Hz)

Treble control action: +/-12dB(8kHz/12kHz)

9 Band-G-EQ:

Line output level:

1 oct step GAIN +/-12dB

(63Hz to 16kHz)

1.8V(CD 1kHz)

General

Power supply voltage: 14.4V DC

(10.8V to 15.6V allowable)

Ground: Negative

Current consumption: Less than 15A, 3A

Speaker impedance: 4 ohm(4 ohm to 8 ohm)

Dimensions(mm):

Weight:

178(W) x 100(H) x 160(D)

2.3kg

WXZ468RMP

COMPONENTS

PE-2758E-A

Main unit

Extension lead

2-1.

FUSE(3A)

2-2 FUSE(15A)

Parts bag

3-1.

Finisher

3-2.

Parts bag

3-2-1. Machine screw(M5 x 8)

3-2-2. Hex-head screw(M5 x 8)

3-2-3. Spacer

3-2-4. Double face

-----------

854-6418-50

120-0030-00

120-0150-00

-----------

383-0591-00

----------1

714-5008-4B 8

716-0496-51

340-1581-00

347-3913-20

To engineers in charge of repair or inspection of our products.

Before repair or inspection, make sure to follow the instructions so that customers and Engineers in charge of repair or inspection can avoid suffering any risk or injury.

1. Use specified parts.

The system uses parts with special safety features against fire and voltage. Use only parts with equivalent characteristics when replacing them.

The use of unspecified parts shall be regarded as remodeling for which we shall not be liable. The onus of product liability

(PL) shall not be our responsibility in cases where an accident or failure is as a result of unspecified parts being used.

2. Place the parts and wiring back in their original positions after replacement or re-wiring.

For proper circuit construction, use of insulation tubes, bonding, gaps to PWB, etc, is involved. The wiring connection and routing to the PWB are specially planned using clamps to keep away from heated and high voltage parts. Ensure that they are placed back in their original positions after repair or inspection.

If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company.

3. Check for safety after repair.

Check that the screws, parts and wires are put back securely in their original position after repair. Ensure for safety reasons there is no possibility of secondary ploblems around the repaired spots.

If extended damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company.

4. Caution in removal and making wiring connection to the parts for the automobile.

Disconnect the battery terminal after turning the ignition key off. If wrong wiring connections are made with the battery connected, a short circuit and/or fire may occur. If extensive damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company.

5. Cautions in soldering

Please do not spread liquid flux in soldering.

Please do not wash the soldering point after soldering.

6. Cautions in soldering for chip capacitors

Please solder the chip capacitors after pre-heating for replacement because they are very weak to heat.

Please do not heat the chip capacitors with a soldering iron directly.

7. Cautions in handling for chip parts.

Do not reuse removed chips even when no abnormality is observed in their appearance. Always replace them with new ones. (The chip parts include resistors, capacitors, diodes, transistors, etc).

Please make an operation test after replacement.

8. Cautions in handling flexible PWB

Before working with a soldering iron, make sure that the iron tip temperature is around 270 . Take care not to apply the iron tip repeatedly(more than three times)to the same patterns.

Also take care not to apply the tip with force.

9. Turn the unit OFF during disassembly and parts replacement.

Recheck all work before you apply power to the unit.

10. Cautions in checking that the optical pickup lights up.

The laser is focused on the disc reflection surface through the lens of the optical pickup. When checking that the laser optical diode lights up, keep your eyes more than 30cms away from the lens. Prolonged viewing of the laser within 30cms may damage your eyesight.

11. Cautions in handling the optical pickup

The laser diode of the optical pickup can be damaged by electrostatic charge caused by your clothes and body. Make sure to avoid electrostatic charges on your clothes or body, or discharge static electricity before handling the optical pickup.

11-1. Laser diode

The laser diode terminals are shorted for transportation in order to prevent electrostatic damage. After replacement, open the shorted circuit. When removing the pickup from the mechanism, short the terminals by soldering them to prevent this damage.

11-2. Actuator

The actuator has a powerful magnetic circuit. If a magnetic material is put close to it. Its characteristics will change. Ensure that no foreign substances enter through the ventilation slots in the cover.

11-3. Cleaning the lens

Dust on the optical lens affects performance.

To clean the lens, apply a small amount of isopropyl alcohol to lens paper and wipe the lens gently.

WXZ468RMP - 2 -

CAUTION

This appilance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT" . In case of any trouble with this player, please contact your nearest "authorized service station" . To prevent direct exposure to the laser beam, do not to open the enclosure.

NOTES OF ISO CONNECTOR

1. For VW/Audi/Opel/Vauxhall vehicles, change the position of fuse installation as shown on the diagram.

(Figure 1)

Initial setting of Ex-lead

Yellow

Fuse

Yellow

Blue/White

Red Red

Blue/White

Remote

ISO

CONNECTOR

Top view

SYSTEM CHECK

This function verifies the devices hooked up through CeNET.

1. Press the [ADJ] button to switch to the adjust mode.

2. Turn the [SEARCH] knob to select "SYS CHECK" .

3. Press and hold the [SEARCH] knob for 1 second or longer to start the system check.

The digital connection configuration is automatically checked.

When the system check is complete, the display returns to the previous mode.

ANTI-THEFT INDICATOR

The red Anti-theft indicator is a function for detering theft.

The disc indicator for the [DIRECT] button "2" blinks.

* The factory default setting is "OFF".

1. Press the [ADJ] button to switch to the adjust mode.

2. Turn the [SEARCH] knob to select "BLINK LED".

3. Turn the [A-MODE] knob to select "ON" or "OFF".

4. Press the [ADJ] button to return to the previous mode.

For models 1992 and later

Yellow

Red Red

Figure 1

For models up to 1991

Yellow

Red

2. When the car stereo is installed in 1998 and later

Volkswagen models, remove the auto antenna leads (A-

5:Blue/White). Be sure to insulate both the ISO connector side terminal and the main unit side terminal with insulation tape, respectively. (Figure 2)

3. When the main unit is also connected to an external am plifier, connect REMOTE on the external amplifier to remote turn-on lead.

Insulation tape

Blue/White Blue/White

Auto ant.(A-5)

Remote turn-on

Figure 2

Insulate the terminal

Never let the terminals make contact with the metal plate parts of the car.

- 3 WXZ468RMP

TROUBLE SHOOTING

Problem

Power does not turn on.

(No sound is produced.)

Nothing happens when buttons are pressed.

Cause

Fuse is blown.

The microprocessor has malfunctioned due to noise, etc.

Measure

Replace with a fuse of the same amperage(3A,15A).

Press the reset button for about 2 seconds with a thin rod.

"Push EJECT" is displayed.

"FAIL**** " is displayed.

No audio.

Something is wrong with disc or mechanism.

Anti-theft function is out of order.

MP3/WMA files are absent on the disc.

Files are not recognized as an MP3/WMA file.

File system is not correct.

MP3/WMA files are not encoded properly.

skipped.

Noise is generated or noise is mixed with sound.

Wrong filename File system is not correct.

Press the [ ] button to avoid the trouble.

If the situation is not improved despite you press the

[ ] button several times.

Press and hold the reset button for 2 seconds or longer.

Write MP3/WMA files onto the disc properly.

Use MP3/WMA files encoded properly.

Use ISO9660 level 1, 2 or JOLIET or Romeo file system.

Use MP3/WMA files encoded properly.

Use ISO9660 level 1, 2 or JOLIET or Romeo file system.

ERROR DISPLAYS

If an error occurs, one of the following displays is displayed.

Take the measures described below to eliminate the problem.

Error Display

ERROR 3

ERROR 4

ERROR 6

ERROR 2

ERROR 3

ERROR 6

ERROR 2

ERROR 3

ERROR 6

Cause

A DISC cannot be played due to scratches, etc.

A foreign object is pinched in the DISC slot, or the shutter is damaged due to opening the shutter forcibly, etc.

A DISC is loaded upside-down inside the

CD deck and cannot play.

A DISC inside the CD changer is not loaded properly.

A DISC inside the CD changer cannot be played due to scratches, etc.

A DISC inside the CD changer cannot be played because it is loaded upside-down.

A DISC inside the DVD changer is not loaded properly.

A DISC cannot be played due to scratches, etc.

A DISC inside the DVD changer cannot be played because it is loaded upside-down.

Measure

Replace with a non-scratched disc.

Remove the object inside the slot.

If there is no foreign object or the situation is not improved in spite of removing it.

Eject the disc then reload it properly.

This is a failure of CD changer's mechanism.

Replace with a non-scratched disc.

Eject the disc then reload it properly.

This is a failure of DVD mechanism.

Retry or replace with a non-scratched disc.

Eject the disc then reload it properly.

ERROR P

ERROR R

Parental level error

Region code error

Set the correct Parental level.

Eject the disc and replace correct region code disc.

If an error display other than the ones described above appears, press the reset button.

If the problem persists, turn off the power.

WXZ468RMP - 4 -

SELF-DIAGNOSIS FUNCTION

Model name/Inducing/Micom version confirmation

1. Press the [ADJ] button to switch to the adjust mode.

2. Turn the [SEARCH] knob to select "SYS CHECK" .

* Micom version display :

Keep pressing the [1] button until the display changes.

Display : " MAIN *. ** "

* Mechanism micom version display :

Keep pressing the [2] button until the display changes.

Display : " MECH **. ** "

* Model name display and inducing display :

Keep pressing the [3] button until the display changes.

Display : " * PE275** "

* CCC-TUNER version display :

Keep pressing the [4] button until the display changes.

Four items of the following are switched with the

[SEARCH] knob.

(1) E2PROM Version display

(2) MapType display

(3) Test Version

(4) Tuner Hardware Version

: " E2pVer_*** "

: " MapType_** "

: " TestVer_** "

: " Hard___*** "

* Keep pushing the [5] button until VFD turn on all the light.

* Keep pushing the [6] button until VFD turn off all the light.

When the micom version is displayed, press the [FUNC] key. Then the micom version display is canceled, enters the state of POWER ON.

When ACC is set to ON from OFF, the micom version display is canceled, too.

Error history confirmation

Take out the disc of the main unit before confirming the error history.

1. Press the [ADJ] button to switch to the adjust mode.

2. Turn the [SEARCH] knob to select "SYS CHECK" .

3. Press the [SCN] button and the [RDM] button at the same time for two seconds or more.

Display : " H01 * * * * "

The number of disk at error

"A" at the first error after back up on

The space at the other modes

It is possible to switch from "H01" to "H20" with the

[SEARCH] knob.

The number of mechanism errors exceeds 20 and a new error occurs, the content of the latest error enters "H01".

* Press the [1] button for one second or more when returning it except the error history confirmation mode.

Error frequency confirmation

1. Press the [2] button for one second or more at the error history confirmation mode.

Display : " T01 * * * * * "

The number of times at error

- 5 -

Clearing the error history and frequency

1. Press the [3] button for two seconds or more at the error history confirmation mode.

2. Press and hold the [6] button pressing the [4] button while displaying as EEP.

Display : " EEP CL3 " " EEP CL2 " " EEP CL1 "

" EEP CL1 " " EEP CL "

3. The error history and frequency are cleared.

4. When ACC is set to ON from OFF, the error history and frequency are cleared again.

RDS error count confirmation

1. Press the [SCN] button and the [1] button at the same time to the tuner mode.

Display : " WAIT "

Display : " * * % * * * "

The number of acquisition of RDS block data

The rate of acquisition of RDS block data

WXZ468RMP

ADJUSTMENT OF CCC-TUNER

: 880-2150A

The data of receiving area and adjustment point are written in the memory of a spare tuner pack. It is possible to receive a broadcast with no adjustment. However, please adjust it to use the unit with the better conditions.

Measuring instrument

1. Personal computer with Windows98SE/WindowsME/

Windows2000 or WindowsXP operating system

2. Adjustment software : CCC-TUNER Alignment for

CeNET soft

3. CeNET analyzer

4. SG

5. AM ANT Dummy box

Writing the parameter

[ Strat up ]

1. Install the adjustment software in the personal computer.

2. Connect the unit to the personal computer with the

CeNET analyzer.

3. Open the adjustment software in the computer, and turn on the unit.

A. Open Comm. PORT

CCC Tuner Alignment for Ce-NET

MENU ALIGNMENT ROM RAM

Settings

Open Comm. PORT

Display

B. Initialization of JIG

Initialization of JIG

C. Incoming connection

Incoming connection

AREA

TUNER RDS TUNER

BAND - Alignment

FM MW(AM) LW

FM S-Meter Slope

Alignment

LEVEL

FM S-Meter Start

Alignment

FM S-Meter Point

Alignment

FM IF-Count

Check

ROM DATA MAP

ROM

DATA Read

Address DATA

DATA Write

DATA

Read ALL

DATA Write (0x70-0xFF)

DATA Write (0x00-0xFF)

CheckSUM

FM S-Meter Adjustment

4. Click the " A. Open Comm.PORT " button of the display.

The communication of the personal computer and the analyzer starts.

5. Click the " B. Initialization of JIG " button of the display.

The personal computer sends the command for operation of the analyzer.

6. Click the " C. Incoming connection " button of the display. The unit recognizes the external jig. The preparation completes.

[ Setting of reception band ]

1. The indicator blinks according to the reception when the connected processing ends normally.

2. The adjustment band is automatically set by the main microcomputer of the unit and memorized in EEPROM in CCC-TUNER.

3. Press the reset button of the unit to set the data.

WXZ468RMP - 6 -

Adjustment for S-meter

1. Connect the antenna input terminal of the unit to S.S.G.

2. Adjustment in order of Slope, Start and Point.

The reception frequency of the set is as follows.

* Reception frequency of FM : 98.1MHz

* Reception frequency of MW : 999kHz

* Reception frequency of LW : 216kHz

Click the " Alignment " button of [ FM S-Meter Slope ] of the display. Then, a set level of SG is displayed.

Set the ATT value of SG to the level.

Input 26dBu at this unit. Click the " OK " button, and the acquisition of the first data starts.

3. A set level of SG is displayed again after a while.

Change the ATT value of SG to the level.

Input 46dBu at this unit.

4. When the adjustment is completed, it is displayed with

" COMPLETED ". Then click the " OK " button.

The acquired value is displayed in the display.

5. Click the " Alignment " button of [ FM S-Meter Start ] of the display. Set the ATT value of SG to the level. Input

26dBu at this unit.

6. When the adjustment is completed, it is displayed with

" COMPLETED ". Then click the " OK " button.

The acquired value is displayed in the display.

7. Click the " Alignment " button of [ FM S-Meter Point ] of the display. Set the ATT value of SG to the level. Input

46dBu at this unit.

8. When the adjustment is completed, it is displayed with

" COMPLETED ". Then click the " OK " button.

The acquired value is displayed in the display.

9. The adjustment of FM was completed.

Change the reception band of the unit to MW, and adjust MW in the order from " Slope " as well as FM.

After adjusting MW, adjust LW as well as MW.

10.After all the adjustments, press the reset button of the unit to set the data.

Confirmation after all adjustments

Reconfirm the version of the parameter file after all adjustments are completed.

1. Press the [ADJ] button to switch to the adjust mode.

2. Turn the [SEARCH] knob to select "SYS CHECK" .

* Microcomputer version display : Keep pressing the [1] button until the display changes.

Display : " MAIN *. ** "

* Model name and destination display : Keep pressing the [3] button until the display changes.

Display : " * PE***** "

* CCC-TUNER version display : Keep pressing the [4] button until the display changes.

Four items of the following are switched with the

[SEARCH] knob.

(1) E2PROM Version display

(3) Test Version

: " E2pVer_*** "

: " TestVer_** "

(2) MapType display

(4) Tuner Hardware Version

: " MapType_** "

: " Hard___*** "

EXPLANATION OF IC

052-3404-10 uPD703272YGC-307-8EA-A System Controller

Terminal Description pin pin

1: A Vref 0

2: A VSS

: - : Reference voltage for the internal ADC.

: - : Negative voltage supply for analog section.

: O : ACC detect signal output.

pin 3: SYS ACC pin 4: LINE SYS MU : O : The system muting command output.

pin 5: A Vref 1 : - : Reference voltage for the internal DAC.

pin 6: NU pin 7: AMP MUTE

: IN : Not in use.

: O : Muting signal output to the Audio Power

Amplifier.

pin 8: FLASH MODE : IN : The flash memory mode setting input.

pin 9: VDD : - : Positive voltage supply.

pin 10: REG C pin 11: GND

: - : The capacitor connection.

: - : Ground.

pin 12: X 1 pin 13: X 2 pin 14: RESET

: - : The crystal connection.

: IN : Reset signal input.

pin 15: XT 1 pin 16: XT 2 pin 17: ILL DET pin 18: CATS DET pin 32: IE BUS RX pin 33: E VSS pin 34: E VDD pin 35: MECH SDA pin 36: MECH SCL

: - : Crystal connection.

: IN : Illumination ON signal input.

: IN : The backup voltage detection for CATS.

pin 19: BU DET 1 : IN : Backup-voltage detection to mute the audio signal.

: IN : Not in use.

pin 20: NU pin 21: ACC DET : IN : ACC detection signal input.

pin 22: DSP I2C SDA :I/O: I2C serial data input/output.

pin 23: DSP I2C SCL : O : I2C serial clock output.

pin 24: NU : IN : Not in use.

pin 25: FLASH TX : O : The serial data output for the flash memory.

pin 26: FLASH RX pin 27: CATS DI pin 28: CATS DO pin 29: CATS SCK pin 30: CATS CS pin 31: IE BUS TX

: IN : The serial data input for the flash memory.

: IN : Serial data input for CATS.

: O : Serial data output for CATS.

: O : Serial clcock output for CATS.

: O : Chip select output for CATS.

: O : IE Bus serial data output.

: IN : IE Bus serial data input.

: - : Ground.

: - : Positive voltage supply.

:I/O: The serial data input/output for GIX-MP3 mechanism.

: O : The serial clock output for GIX-MP3 mechanism.

pin 37: MECH SRQ : IN : The request input from GIX-MP3 mechanism.

pin 38: MECH RESET : O : The reset signal output for GIX-MP3 mechanism.

pin 39: RDS TP 3 pin 40: NU

: O : The test point for RDS PI.

: IN : Not in use.

pin 41: NU pin 42: DSP RESET pin 43: TUN SDA

: IN : Not in use.

: O : Reset signal output to the DSP IC.

:I/O: I2BUS serial data input/output for the tuner pack.

pin 44: TUN SCL : O : I2BUS serial clock output for the tuner pack.

: IN : RDS serial clock input.

pin 45: TUN RD CL pin 46: TUN RD DA pin 47: REMOCON pin 48: VFD LAT pin 49: VFD BLANK

: IN : RDS serial data input.

: IN : Remote controller signal input terminal.

: O : The latch strove signal output to the VFD driver.

: O : Blank pulse output to the VFD driver.

pin 50: MECHA MUTE : IN : Mechanism audio mute signal input.

pin 51: VFD DO pin 52: VFD CLK pin 53: CTRL

: O : The serial data output to the VFD driver.

: O : The clock pulse output to the VFD driver.

: O : Power supply ON signal output.

pin 54: INT AMP REM : O : ON signal output to the internal Amplifier.

pin 55: NU : IN : Not in use.

- 7 pin 56: KEY INT pin 57: NU pin 58: NU pin 59: 5V REM pin 60: CD 9V REM pin 61: MECH ACC pin 62: CLK TEST pin 63: INIT 1 pin 64: INIT 2 pin 65: LED 1 pin 66: LED 2 pin 67: LED 3 pin 68: NU pin 69: B VSS pin 70: B VDD pin 71: KEY DI pin 72: KEY DO pin 73: KEY CK pin 74: KEY CE pin 75: KEY RESET pin 76: NU pin 77: VOL CW pin 78: VOL CCW

: IN : Key interrupting signal input.

: IN : Not in use.

: O : ON signal output to the 5V power supply.

: O : 9V power supply ON signal output for CD.

H=ON.

: O : Mechanism ACC control signal output.

: O : Sub clock test port.

: IN : The initial setting input.

Refer Table 1.

: IN : The initial setting input.

Refer Table 1.

: O : LED ON signal output. H=ON.

: IN : Not in use.

: - : Ground for the bus interface section.

: - : Positive voltage supply for the bus interface section.

: IN : The serial data input from the Key scan

IC.

: O : The serial data output to the Key scan IC.

: O : Clock pulse output to Key-IC.

: O : Chip enable output to Key-IC.

: O : Reset pulse output to Key-IC.

: IN : Not in use.

: IN : The pulse signal input from the rotary encoder.

pin 79: SOURCE CW : IN : The pulse signal input from the rotary encoder.

pin 80: SOURCE CCW : IN : The pulse signal input from the rotary encoder.

pin 81: A-MODE CW : IN : The pulse signal input from the rotary encoder.

pin 82: A-MOME CCW : IN : The pulse signal input from the rotary encoder.

pin 83: PHONE INT pin 84: SPAN A pin 85: SPAN B

: IN : The telephone interrupt signal input.

: O : Spectrum analyzer frequency band selection signal output.

pin 86: SPAN C pin 87: ILL REM pin 88: DD REM pin 89: SPAN DATA

: O : Spectrum analyzer frequency band selection signal output.

: O : Key illumination ON signal output. H=ON.

: O : DC to DC Converter ON signal output.

H=ON.

: IN : The serial data input from the spectrum analyzer.

pin 90: KEY AD pin 91: NU pin 92: NU pin 93: LEVEL IN L pin 94: LEVEL IN R pin 95: NU pin 96: NU pin 97: RDS TP 1

: IN : Input terminal of A/D converter for Key judgment.

: IN : Not in use.

: IN : Power level detection port.

: IN : Not in use.

: O : The test point for RDS.

pin 98: RDS TP 2 : O : The test point for RDS.

pin 99: EXT AMP REM : O : ON signal output to the external Amplifier.

pin100: A ANT REM : O : The automatic antenna control signal output.

Table 1. The initial setting input

Destination

INIT 1 ( pin 63 )

INIT 2 ( pin 64 )

Japan

Europe

Asia

WXZ468RMP

BLOCK DIAGRAM

SYS MUTE

ANT

ILL 8V

CTRL

AUDIO 9V

VCC

AMP CTRL

ACC DET

ACC 5V

B/U 5.7V

ACC IN

AMP

(D2)

ACC 5V

ACC 3.3V

SYS 5V

GOLD-C

ACC 3.3V

2.0V DET

DSP-SCL DSP-SDA DSP-RST

SDA

SCL

RDDA

RDCL

PLL 8.5V

MAIN 8.5V

IIC 5.0V

(ACC 3.3V)

A/B/C

DATA

POWER LEVEL(L/R)

MAIN

MICOM

UPD703272YGC

(IC601)

SYS MUTE

B/U 4V

B/U 3.3V

8V SW

Ce-NET 13PIN

KEY ILL

DISC ILL

RESET

EJECT

POWER

LOAD

PRESET x3

(IR701) RS-671

PRESET x3

(Q794) (Q795) (Q796)

(Q797) (Q798) (Q799)

Ce-NET 13PIN

WXZ468RMP

(BL1)

CCC-TUNER

880-2150A

AUDIO+ (L,R)

13 PIN

SYS-ACC

ILL DET

BUS 14V

CHANGER

MECHANISM

B/U

- 8 -

NO.

EXPLODED VIEW/PARTS LIST

Escutcheon section

34 31

16 34

PART NO.

DESCRIPTION

371-5820-00 FACE PANEL(A)

371-5821-00 FACE PANEL(B)

371-5822-00 FACE PANEL(C)

371-5823-01 FACE PANEL(D)

371-5824-00 FACE PANEL(E)

373-1073-02 DIAL-CVR

380-5635-00 KNOB

335-7548-00 KNOB-CAP

335-7573-00 KNOB-RING

380-5636-00 KNOB (A)

380-5637-00 KNOB (B)

370-6176-01 ESCUTCHEON

335-7547-00 FILTER(VFD)

335-7549-00 ILLUMI PLATE(L)

335-7550-00 ILLUMI PLATE(R)

382-7458-00 BUTTON(RESET)

382-7451-00 BUTTON(BAD/D-Z)

382-7452-01 BUTTON(TA/ADJ)

382-7453-00 BUTTON(1,2,3)

382-7454-00 BUTTON(TIE/RDM)

382-7455-00 BUTTON(SCN/RPT)

382-7459-00 BUTTON(4,5,6)

382-7456-00 BUTTON(CD/S-A)

382-7457-00 BUTTON(L/D)OU

335-7553-00 ILLUMI PLATE(B)

335-7557-00 ILLUMI PLATE(L)

335-7556-00 ILLUMI PLATE(R)

346-0180-00 LEATHER SHEET

371-5832-01 TRIM PLATE

335-7551-00 ILLUMI PLATE(CD)

335-7561-00 ILLIMI-PLATE(A)

335-7555-00 ILLUMI PLATE(B)

NO.

Q'TY

- 9 -

38 x19

8 33

41 39

50 39

PART NO.

DESCRIPTION

347-7528-00 DOUBLE FACE

380-5616-00 KNOB CAP

716-0872-52 PAD SCREW(M1.7 x 5)

347-7526-00 DOUBLE FACE

347-7243-00 DOUBLE FACE

013-6312-50 SWITCH

001-7040-91 LED(WHITE)

001-7043-90 LED(GREEN)

001-7062-90 LED(RED)

379-4056-28 VFD

347-7405-00 SPACER

060-4017-90 IR-RECIEVER

716-0778-51 WAVE SCREW(2 x 6)

074-3010-72 OUTLET SOCKET(22P)

074-3010-60 OUTLET SOCKET(10P)

----------SWITCH PWB

016-9901-00 VR W/SHAFT(SEARCH)

016-9900-94 VR W/SHAFT

(A-MODE,SOURCE)

016-9900-84 VR W/SHAFT(VOLUME)

347-7878-00 FILM

001-7095-90 LED(BLUE)

335-7554-00 ILLUMI PLATE

345-8090-00 CUSHION RUBBER

347-7884-00 FILM(E)

347-7877-00 FILM(D)

347-7876-00 FILM(C)

347-7875-00 FILM(B)

347-7874-00 FILM(A)

347-7321-00 E-SHEET

345-5598-00 CUSHION

347-6548-00 DOUBLE FACE

WXZ468RMP

Q'TY

Main section

27 2 29

26 26 21 25

NO.

WXZ468RMP

PART NO.

DESCRIPTION

311-1896-10 LOWER CASE

310-1799-10 UPPER CASE

309-0813-00 FRONT-BRKT

331-4036-00 MECH-BRKT(L)

331-4037-00 MECH-BRKT(R)

313-1941-00 HEAT SINK

929-0371-81 CD-CHANG-MODULE

816-4023-50 FLAT WIRE

345-3799-20 RUBBER PART

286-6687-00 SETPLATE

341-1823-00 SHAFT-S

347-7229-00 SPACER FILM

076-0648-22 PLUG(22P)

076-0648-10 PLUG(10P)

----------MAIN PWB

073-0762-90 TERMINAL

880-2150A CCC-TUNER

Q'TY

NO.

PART NO.

DESCRIPTION

092-4000-51 ANT-RECEPT

074-1214-00 OUTLET SOCKET

074-1194-00 OUTLET SOCKET(Ce-NET)

331-4035-00 IC HOLDER

074-1237-69 OUTLET SOCKET(19P)

307-0714-00 REAR PLATE

855-5535-50 RCA PIN CORD

716-0878-50 IT SCREW(M2.6 x 5)

714-3008-85 MACHINE SCREW(M3 x 8)

714-2606-8B MACHINE SCREW(M2.6 x 6)

780-3006-51 SCREW(M3 x 6)

714-2610-8B MACHINE SCREW(M2.6 x 10)

716-3552-00 SCREW(M2.3 x 2.5)

060-6028-00 DC-DC CONVERTER

335-0833-01 LEAD HOLDER

855-0569-52 MINI JACK CORD

Q'TY

- 10 -

ELECTRICAL PARTS LIST

Switch PWB(B1) section

REF No. PART No.

DESCRIPTION

D720

D721

D722

D751

D752

D753

D754

D755

D712

D713

D714

D715

D716

D717

D718

D719

C710

D705

D706

D707

D708

D709

D710

D711

C701

C702

C703

C704

C705

C706

C708

C709

D756

D757

D758

D759

D766

D767

168-1042-78 16V 0.1uF

168-1022-55 1000pF K

042-0423-97 16V 10uF

168-1032-55 0.01uF K

168-1042-78 16V 0.1uF

168-1022-55 1000pF K

168-1042-78 16V 0.1uF

043-0318-90 5600pF

001-7040-91 NSCW100-T

001-7095-90 HUB1105W-12-RR

001-7040-91 NSCW100-T

001-7043-90 CL-170FG F-GREEN

001-7062-90 RBR1111C

001-0516-90 MA111

001-4301-32 HZU 5.6B2

001-4301-21 HZU3.9B2

REF No. PART No.

DESCRIPTION

R718

R719

R720

R721

R722

R723

R724

R725

R710

R711

R712

R713

R714

R715

R716

R717

J702

L701

Q794

Q795

Q796

Q797

Q798

Q799

D768

D769

D770

D771

001-4301-32 HZU 5.6B2

FL701 379-4056-28 VFD

IC701 051-6642-08 LC75700T

IR701 060-4017-90 IR RECEIVER

J701 074-3010-60 10P

074-3010-72 22P

010-3406-66 NLV25 22uH J

125-2199-96 KRC106S

R726

R727

R728

R729

R730

R736

119-1021-15 1/10W 1k ohm

119-3931-15 1/10W 39k ohm

119-2211-15 1/10W 220 ohm

119-2711-15 1/10W 270 ohm

119-8211-15 1/10W 820 ohm

119-5611-15 1/10W 560 ohm

119-8211-15 1/10W 820 ohm

119-2711-15 1/10W 270 ohm

119-3311-15 1/10W 330 ohm

119-1011-15 1/10W 100 ohm

119-1021-15 1/10W 1k ohm

119-3331-15 1/10W 33k ohm

Main PWB(B2) section

REF No. PART No.

DESCRIPTION

C25

C102

C103

C104

C105

C106

C107

C108

C109

C110

C116

C125

C11

C12

C13

C15

C16

ANT1 092-4000-51 ANTENNA RECEPT

BL1 880-2150A CCC-TUNER

166-1511-50 150pF CH

187-4763-35 16V 47uF

168-2232-55 0.022uF K

187-4763-35 16V 47uF

168-2232-55 0.022uF K

187-4763-35 16V 47uF

168-2232-55 0.022uF K

187-1063-35 16V 10uF

166-2201-50 22pF CH

166-1011-50 100pF CH

168-4732-78 0.047uF K

187-2253-65 50V 2.2uF

178-4742-78 0.47uF

187-1063-35 16V 10uF

187-2253-65 50V 2.2uF

172-1041-15 0.1uF

187-1053-65 50V 1uF

178-4742-78 0.47uF

168-1022-55 1000pF K

REF No. PART No.

DESCRIPTION

C219

C220

C221

C223

C224

C225

C226

C301

C302

C303

C304

C305

C206

C207

C210

C211

C214

C216

C217

C218

C126

C127

C128

C129

C130

C131

C132

C205

168-1022-55 1000pF K

042-1393-00 35V 100uF

042-1655-00 63V100uF

042-9134-00 63V 47uF

168-1042-78 16V 0.1uF

189-3383-32 16V 3300uF

168-1042-78 16V 0.1uF

187-1073-35 16V 100uF

168-1042-78 16V 0.1uF

187-1073-35 16V 100uF

168-4732-78 0.047uF K

168-2232-55 0.022uF K

187-4763-35 16V 47uF

168-1042-78 16V 0.1uF

166-1501-50 15pF CH

168-1032-55 0.01uF K

187-4753-55 35V 4.7uF

- 11 -

REF No. PART No.

DESCRIPTION

R745

R746

R747

S701

S702

S703

S704

S705

R737

R738

R739

R740

R741

R742

R743

R744

119-2721-15 1/10W 2.7k ohm

119-1201-15 1/10W 12 ohm

119-3311-15 1/10W 330 ohm

119-1031-15 1/10W 10k ohm

119-3311-15 1/10W 330 ohm

013-6312-50 SKRP-ABE-010

S706

S707

S708

S709

S710

S711

S712

S713

013-6312-50 SKRP-ABE-010

S714

S715

S716

S717

013-6312-50 SKRP-ABE-010

S718

S719

013-6312-50 SKRP-ABE-010

VR701 016-9900-84 VR W/SHAFT

VR702 016-9900-94 VR W/SHAFT

VR703 016-9900-94 VR W/SHAFT

VR704 016-9901-00 VR W/SHAFT

PWB 039-2797-01 PWB(WITHOUT

COMPONENT)

REF No. PART No.

DESCRIPTION

C325

C326

C327

C328

C329

C330

C331

C332

C333

C340

C341

C401

C314

C315

C316

C318

C319

C322

C323

C324

C306

C307

C308

C309

C310

C311

C312

C313

168-1032-55 0.01uF K

043-0540-02 16V 1uF

187-1063-35 16V 10uF

168-1042-78 16V 0.1uF

042-1631-50 10V 100uF

168-1042-78 16V 0.1uF

187-1063-35 16V 10uF

168-1042-78 16V 0.1uF

187-1063-35 16V 10uF

168-1042-78 16V 0.1uF

168-1022-55 1000pF K

166-1011-50 100pF CH

168-1022-55 1000pF K

166-1011-50 100pF CH

168-1022-55 1000pF K

166-1011-50 100pF CH

042-1631-50 10V 100uF

168-1042-78 16V 0.1uF

168-4732-78 0.047uF K

168-1042-78 16V 0.1uF

WXZ468RMP

REF No. PART No.

DESCRIPTION

C577

C578

C579

C601

C602

C603

C604

C605

C569

C570

C571

C572

C573

C574

C575

C576

C606

C607

C608

C609

C610

C611

C612

C613

C614

C615

C558

C559

C560

C561

C565

C566

C567

C568

C542

C551

C552

C553

C554

C555

C556

C557

C502

C503

C504

C505

C506

C507

C522

C541

C448

C449

C450

C453

C454

C455

C456

C501

C412

C413

C414

C415

C416

C417

C421

C447

C402

C404

C405

C406

C408

C409

C410

C411

187-1063-35 16V 10uF

187-2253-65 50V 2.2uF

168-8222-55 8200pF K

168-4732-78 0.047uF K

168-8222-55 8200pF K

168-4732-78 0.047uF K

187-2253-65 50V 2.2uF

187-1063-35 16V 10uF

187-2253-65 50V 2.2uF

168-1042-78 16V 0.1uF

187-1063-35 16V 10uF

168-1032-55 0.01uF K

166-1011-50 100pF CH

187-1063-35 16V 10uF

187-3363-45 25V 33uF

166-1011-50 100pF CH

042-0423-94 10V 4.7uF

166-1801-50 18pF CH

166-2201-50 22pF CH

168-1032-55 0.01uF K

042-1577-00 6.3V 100uF

166-1011-50 100pF CH

166-3911-50 390pF CH

187-1073-35 16V 100uF

042-1596-00 5.5V 0.33F

168-1042-78 16V 0.1uF

168-1032-55 0.01uF K

168-1042-78 16V 0.1uF

168-4732-78 0.047uF K

187-1063-35 16V 10uF

187-2253-65 50V 2.2uF

168-1042-78 16V 0.1uF

168-8222-55 8200pF K

187-1063-35 16V 10uF

166-1011-50 100pF CH

168-1042-78 16V 0.1uF

168-2222-55 2200pF K

166-2711-50 270pF

168-1042-78 16V 0.1uF

187-1063-35 16V 10uF

WXZ468RMP

REF No. PART No.

DESCRIPTION

D213

D214

D215

D216

D217

D301

D501

D502

D202

D203

D205

D206

D208

D209

D210

D211

C625

C626

C627

C628

C631

C632

D201

C616

C617

C618

C619

C621

C622

C623

C624

187-2263-15 6.3V 22uF

168-1042-78 16V 0.1uF

042-1596-00 5.5V 0.33F

168-4732-78 0.047uF K

187-1063-35 16V 10uF

187-4763-35 16V 47uF

168-1042-78 16V 0.1uF

168-2232-55 0.022uF K

168-1042-78 16V 0.1uF

168-2232-55 0.022uF K

166-1011-50 100pF CH

001-0535-90 MA729

001-0424-31 MA4180

001-0347-42 MA4075H

001-0592-61 1N5404

001-0516-90 MA111

001-0466-91 S5688G

001-0516-90 MA111

001-0644-90 MA113

001-0516-90 MA111

001-0644-90 MA113

001-0516-90 MA111

001-0466-91 S5688G

001-4301-21 HZU3.9B2

001-0516-90 MA111

D554

D601

D602

D603

D604

D605

D606

D607

D503

D504

D505

D506

D507

D551

D552

D553

001-4301-24 HZU 4.3B3

001-4301-41 HZU 7.5B2

001-0535-90 MA729

001-0516-90 MA111

001-4301-32 HZU 5.6B2

001-0504-31 HZS6 A2L

001-0535-90 MA729

001-0529-26 MA8047-M

001-0516-90 MA111

D608

D609

D610

D611

001-0516-90 MA111

001-0347-38 MA4068M

001-0516-90 MA111

001-0347-48 MA4091H

F201 060-8053-90 CHIP FUSE 1.3A

FIL302 060-3115-51 CKD310JB1C224ST

FIL303 060-3115-51 CKD310JB1C224ST

IC101 051-2057-00 TB2906HQ

IC201 051-3324-00 HA13168

IC202 060-6028-00 DC-DC CON-

VERTER

IC203 051-3335-90 AN77L04M

IC301 051-6722-90 TAS3103IDBTR

IC302 051-6723-90 PCM3010DBR

IC401 051-5818-90 BA3834F

IC402 051-3054-90 HA17558ATEL

IC403 051-3054-90 HA17558ATEL

IC551 051-3054-90 HA17558ATEL

IC552 051-3054-90 HA17558ATEL

IC553 051-3054-90 HA17558ATEL

IC554 051-3054-90 HA17558ATEL

IC601 052-3404-10 uPD703272YGC-

307-8EA-A

IC602 051-6600-58 HA12187FP

IC603 051-5446-08 BD4843G-TR

IC604 051-5410-18 S-80820CNMC-8BF

REF No. PART No.

DESCRIPTION

Q605

Q606

Q607

Q608

Q609

Q610

Q613

Q614

Q456

Q501

Q502

Q503

Q601

Q602

Q603

Q604

Q615

Q618

Q619

R101

R102

Q212

Q213

Q214

Q215

Q216

Q453

Q454

Q455

L603

P601

P602

Q203

Q205

Q206

Q207

Q208

L407

L408

L409

L410

L520

L521

L601

L602

L303

L304

L305

L401

L403

L404

L405

L406

L101

L201

L202

L203

L301

L302

IC605 051-9400-29 BR93L46F-W

IC606 051-7285-08 CD74HC4050PWR

IC607 051-5418-18 BD4827G

J101 074-1214-00 16P

J601

J901

074-1194-00 13P CE-NET

074-1237-69 19PIN

010-2003-04 30uH

010-6009-70 6.8uH

010-8038-01 130uH

010-6009-88 220uH J

010-2272-03 100uH

010-6009-69 5.6uH J

010-3103-64 1.5k ohm/100MHz

010-3406-50 NLV25 1uH J

010-3103-64 1.5k ohm/100MHz

010-3105-62 1k ohm/100MHz

010-6009-80 47uH J

010-6009-69 5.6uH J

010-6009-80 47uH J

076-0648-10 10P

076-0648-22 22P

125-4015-90 KTC2026

191-1243-00 2SB1243

125-4010-90 KTC3875S

191-1243-00 2SB1243

191-1237-00 2SB1237

125-0013-97 RN2427

125-2199-92 KRC102S

125-4012-90 KTD1304

125-2199-96 KRC106S

125-0199-96 KRA106S

125-4010-90 KTC3875S

125-3004-90 KTA1504S

125-4010-90 KTC3875S

125-0199-92 KRA102S

125-2199-93 KRC103S

125-3004-90 KTA1504S

125-2199-92 KRC102S

125-4015-90 KTC2026

125-3007-90 KTA1298

125-2199-92 KRC102S

125-0199-93 KRA103S

192-2712-00 2SC2712

125-0199-92 KRA102S

125-2199-96 KRC106S

119-4721-15 1/10W 4.7k ohm

119-1041-15 1/10W 100k ohm

119-1031-15 1/10W 10k ohm

119-2731-15 1/10W 27k ohm

- 12 -

REF No. PART No.

DESCRIPTION

R431

R432

R447

R448

R449

R450

R453

R454

R416

R417

R418

R419

R420

R421

R427

R429

R403

R404

R410

R411

R412

R413

R414

R415

R336

R337

R340

R341

R342

R343

R401

R402

R305

R312

R313

R314

R315

R333

R334

R335

R216

R217

R218

R219

R220

R230

R231

R304

R208

R209

R210

R211

R212

R213

R214

R215

R112

R113

R114

R115

R201

R202

R203

R206

119-1021-15 1/10W 1k ohm

119-6831-15 1/10W 68k ohm

119-1041-15 1/10W 100k ohm

119-1031-15 1/10W 10k ohm

119-2211-15 1/10W 220 ohm

116-5611-15 1/4W 560 ohm

119-4731-15 1/10W 47k ohm

116-2721-15 1/4W 2.7k ohm

119-4721-15 1/10W 4.7k ohm

116-1031-15 1/4W 10k ohm

119-1021-15 1/10W 1k ohm

119-2231-15 1/10W 22k ohm

119-4731-15 1/10W 47k ohm

116-1831-15 1/4W 18k ohm

116-1521-15 1/4W 1.5k ohm

119-1801-15 1/10W 18 ohm

119-1041-15 1/10W 100k ohm

119-4721-15 1/10W 4.7k ohm

119-0000-05 1/10W 0 ohm JW

119-1521-15 1/10W 1.5k ohm

119-8211-15 1/10W 820 ohm

119-2211-15 1/10W 220 ohm

119-0000-05 1/10W 0 ohm JW

119-3311-15 1/10W 330 ohm

119-1541-15 1/10W 150k ohm

119-1531-15 1/10W 15k ohm

119-1041-15 1/10W 100k ohm

119-1541-15 1/10W 150k ohm

119-1041-15 1/10W 100k ohm

119-1021-15 1/10W 1k ohm

119-1041-15 1/10W 100k ohm

032-0140-00 1/10W 56k ohm F

032-0140-54 1/10W 22k ohm F

119-1011-15 1/10W 100 ohm

119-1031-15 1/10W 10k ohm

119-2211-15 1/10W 220 ohm

119-2231-15 1/10W 22k ohm

REF No. PART No.

DESCRIPTION

R611

R612

R613

R614

R615

R622

R623

R624

R602

R603

R604

R606

R607

R608

R609

R610

R580

R581

R582

R583

R584

R585

R586

R601

R572

R573

R574

R575

R576

R577

R578

R579

R562

R564

R566

R567

R568

R569

R570

R571

R554

R555

R556

R557

R558

R559

R560

R561

R523

R536

R537

R538

R540

R551

R552

R553

R455

R456

R459

R460

R461

R462

R464

R465

119-2231-15 1/10W 22k ohm

119-3311-15 1/10W 330 ohm

119-1021-15 1/10W 1k ohm

119-3311-15 1/10W 330 ohm

119-1021-15 1/10W 1k ohm

119-8221-15 1/10W 8.2k ohm

119-3321-15 1/10W 3.3k ohm

119-2231-15 1/10W 22k ohm

032-0140-00 1/10W 56k ohm F

032-0140-51 1/10W 15k ohm F

119-2211-15 1/10W 220 ohm

119-2431-15 1/10W 24k ohm

119-2211-15 1/10W 220 ohm

119-2431-15 1/10W 24k ohm

119-3931-15 1/10W 39k ohm

119-1041-15 1/10W 100k ohm

119-1021-15 1/10W 1k ohm

119-3921-15 1/10W 3.9k ohm

119-1021-15 1/10W 1k ohm

119-3921-15 1/10W 3.9k ohm

119-1041-15 1/10W 100k ohm

119-8221-15 1/10W 8.2k ohm

119-0000-05 1/10W 0 ohm JW

116-6801-15 1/4W 68 ohm

119-3321-15 1/10W 3.3k ohm

119-1031-15 1/10W 10k ohm

119-1021-15 1/10W 1k ohm

119-4731-15 1/10W 47k ohm

119-4721-15 1/10W 4.7k ohm

119-1031-15 1/10W 10k ohm

116-1521-15 1/4W 1.5k ohm

119-4731-15 1/10W 47k ohm

119-4721-15 1/10W 4.7k ohm

119-1031-15 1/10W 10k ohm

116-1811-15 1/4W 180 ohm

119-5621-15 1/10W 5.6k ohm

REF No. PART No.

DESCRIPTION

R649

R652

R653

R654

R655

R656

R660

R661

R641

R642

R643

R644

R645

R646

R647

R648

R633

R634

R635

R636

R637

R638

R639

R640

R625

R626

R627

R628

R629

R630

R631

R632

R672

R674

R675

R680

R681

R682

R683

R684

R662

R663

R664

R665

R666

R667

R668

R671

R685

R686

R687

R697

119-3311-15 1/10W 330 ohm

119-0000-05 1/10W 0 ohm JW

R698 119-0000-05 1/10W 0 ohm JW

SUP1 060-0122-91 DSP-141N-S00B

TM201 073-0762-90 TERMINAL

TM203 073-0762-90 TERMINAL

TM204 073-0762-90 TERMINAL

X301

X601

X602

PWB

061-3536-90 11.2896MH

060-1541-90 3.14MHz

061-1056-00 32.768kHz

039-2796-01 PWB(WITHOUT

COMPONENT)

119-1031-15 1/10W 10k ohm

116-1811-15 1/4W 180 ohm

119-2231-15 1/10W 22k ohm

119-1031-15 1/10W 10k ohm

119-4721-15 1/10W 4.7k ohm

119-1031-15 1/10W 10k ohm

119-1011-15 1/10W 100 ohm

119-1031-15 1/10W 10k ohm

119-2241-15 1/10W 220k ohm

119-4731-15 1/10W 47k ohm

119-1531-15 1/10W 15k ohm

119-1031-15 1/10W 10k ohm

119-4721-15 1/10W 4.7k ohm

119-4731-15 1/10W 47k ohm

119-1021-15 1/10W 1k ohm

119-1031-15 1/10W 10k ohm

119-1041-15 1/10W 100k ohm

119-1031-15 1/10W 10k ohm

119-1041-15 1/10W 100k ohm

119-0000-05 1/10W 0 ohm JW

119-3311-15 1/10W 330 ohm

119-1041-15 1/10W 100k ohm

119-0000-05 1/10W 0 ohm JW

119-1221-15 1/10W 1.2k ohm

119-3311-15 1/10W 330 ohm

CONNECTOR LAYOUT

AUX-IN / LEFT

AUX-IN / RIGHT

WHITE

RED

REAR / LEFT

REAR / RIGHT

LINE-OUT

FRONT / LEFT

WHITE

RED

WHITE

FRONT / RIGHT RED

CAR

WIRED

REMOCON

C L 0 7 2 8

RED

BLACK

RCA PIN CORD

855-5535-50

GRAY

MINI JACK CORD

855-0569-52

M5 x 6 mm MA X

J601 (CeNET)

11 12

7 8 9 10

3 4 5 6

1 13 2

No. Description

1 GND

2 BACK UP

3 L-CH(+)

4 N.C.

5 N.C.

6 BUS(+)

7 R-CH(+)

8 R-CH(-)

9 SYS-ACC

10 BUS(-)

11 L-CH(-)

12 ILLUMI

13 N.C.

J601

RADIO ANT

Pin No.

(J101 -

ISO)

Color Description

1 - B7 GRN SP R/L(+)

2 - B8 GRN/BLK SP R/L(-)

3 - B6 WHT/BLK SP F/L(-)

4 BRN

5 - B5 WHT

6 - A7 RED

7 - B3 GRY

PHONE INT

SP F/L(+)

ACC

SP F/R(+)

8 N.C

9 - B4 GRY/BLK SP F/R(-)

10 - A5 BLU/WHT REMOTE

11 - B1 PUR SP R/R(+)

12 - A6 ORG/WHT ILLUMI

13 - B2 PUR/BLK SP R/R(-)

14 YEL BACK UP(BUS)

(3A FUSE)

15 - A4 YEL

16 - A8 BLK

BACK UP

(15A FUSE)

GND

N.C

ISO CONNECTOR

B7 B8

B5 B6

A7 A8

A5 A6

B3 B4

B1 B2

A3 A4

A1 A2

J101

1 3 5 7 9 11 13 15

2 4 6 8 10 12 14 16

EXTENSION LEAD

854-6418-50

GRY / BLK

WHT / BLK

GRAY

WHITE

PUR / BLK

GRN / BLK

PURPLE

GREEN

REMOTE

BLU / WHT

BLACK

ACC

RED

BACK UP

PHONE

MUTE BROWN

ORG / WHT

FUSE(3A)

120-0030-00

15A

FUSE(15A)

120-0150-00

YELLOW

- 13 WXZ468RMP

CIRCUIT DIAGRAM

Switch PWB(B1) section

FL701

1 2 5 6 7 8 9 10 11 12 13

S701

S702

S703

SPE/ANA

S704

DISP

VR704(1/2)

<< DN

S705

S706

S707

BAND

S708

RDM

S709

S710

S711

S712

RPT

VR704(2/2)

ENT

57 58 59 60 61 62 63 64 65 68 69

S713

TITLE

S714

D-Z

S715

ADJ

S716

SCN

VR703(2/2)

G.EQ

KI1

KI2

KI3

KI4

KI5

KS4

KS3

KS2

KS1

KI5

KI4

KI3

KI2

KI1

R738

R739

P_1

P3/

KS5

P4/

P2/

KS6

KS3

KS2

VSS

OSC

KS1

KI5

VDD

RST

KI4

KI3

KI2

KI1

IC701

LC75700T

3.2V

R744 10K

R745

R746

R747

330

RST

L701 22uH

R728

100

V G1 G2 O

10 16V TAN

D721

MA111

R729

R736

33K

R737

2.7K

R740

R741

R742

R743

330

8.0V

47.6V

J701

074-3010-60

F-GND

GND

VFD_CLK

VFD_DO

VFD_BLK

VFD_LAT

FILA1

FILA2

VHV

D/D-GND

RST

A-M_CCW

A-M_CW

SRC_CCW

SRC_CW

VOL_CCW

VOL_CW

4.0V

P_3

P_2

P_1

3.3V

5.2V

3.2V

J702

074-3010-72

N.C

RESET

A-M_CCW

A-M_CW

SRC_CCW

SRC_CW

VOL_CCW

VOL_CW

KEY_RST

KEY_CE

KEY_CL

KEY_DI

KEY_DO

B/U 4V

LED_3

LED_2

LED_1

REMOCON

KEY-INT

SYS +5V

ACC 3.3V

KEY-ILL

- 14 WXZ468RMP

PRINTED WIRING BOARD

Switch PWB(B1) section

COMPONENT SIDE

Caution:

COMPONENT SIDE: Parts on the component side seen from the component side are indicated.

SOLDER SIDE: Parts on the solder side seen from the solder side are indicated.

SOLDER SIDE

- 15 WXZ468RMP

Main PWB(B2) section

: Component side

LINE OUT

AUX-IN

LEFT

AUX-IN

RIGHT

REAR

LEFT

REAR

RIGHT

FRONT

LEFT

FRONT

RIGHT

WHITE

RED

WHITE

RED

WHITE

RED

RCA PIN CORD

855-5535-50

RED

No. Description

1 SP R/L(+)

3 SP F/L(-)

5 SP F/L(+)

7 SP F/R(+)

9 SP F/R(-)

11 SP R/R(+)

13 SP R/R(-)

15 BACK UP

No. Description

2 SP R/L(-)

4 PHONE INT

6 ACC

8 N.C

10 REMOTE

12 ILLUMI

14 BACK UP(BUS)

16 GND

J101

14 12 10 8 6 4 2

13 11 9 7 5 3 1

* Refer to page 13

for the extension lead

(854-6418-50).

BLACK

GRAY

10 1

CAR

WIRED

REMOCON

MINI JACK CORD

855-0569-52

J601

Ce-NET

8 7

No. Description

1 GND

2 BACK UP

3 L-CH(+)

4 N.C.

5 N.C.

6 BUS(+)

7 R-CH(+)

No. Description

8 R-CH(-)

9 SYS-ACC

10 BUS(-)

11 L-CH(-)

12 ILLUMI

13 N.C.

DC-DC converter

COMPONENT SIDE

Caution:

COMPONENT SIDE: Parts on the component side seen

from the component side are indicated.

- 16 -

Flat wire

816-4023-50

To page M16

J1 of CD changer mechanism

To page 15

J701 of Switch PWB

WXZ468RMP

To page 15

J702 of Switch PWB

Main PWB(B2) section

: Solder side

No. Description

1 GND

2 BACK UP

3 L-CH(+)

4 N.C.

5 N.C.

6 BUS(+)

7 R-CH(+)

No. Description

8 R-CH(-)

9 SYS-ACC

10 BUS(-)

11 L-CH(-)

12 ILLUMI

13 N.C.

11 12

7 8 9 10

3 4 5 6

1 13 2

1 3 5 7 9 11 13

2 4 6 8 10 12 14

No. Description

1 SP R/L(+)

3 SP F/L(-)

5 SP F/L(+)

7 SP F/R(+)

9 SP F/R(-)

11 SP R/R(+)

13 SP R/R(-)

15 BACK UP

No. Description

2 SP R/L(-)

4 PHONE INT

6 ACC

8 N.C

10 REMOTE

12 ILLUMI

14 BACK UP(BUS)

16 GND

1 10

1 3

SOLDER SIDE

Caution:

SOLDER SIDE: Parts on the solder side seen

from the solder side are indicated.

The parts of a dotted line express the parts on a component side.

- 17 WXZ468RMP

CIRCUIT DIAGRAM

Main PWB(B2) section 1/3

To page 19

Main PWB 2/3

TUN_RDDA 2

TUN_RDCL

LEVEL_IN_L

LEVEL_IN_R

DSP_SCL

DSP_SDA

DSP_RESET

TUN_SCL

TUN_SDA

CDM_RCH

CDM_S-GND

CDM_LCH

R684

330

T_RDDA

R685

330

T_RDCL

LV_L

LV_R

DSP_SCL

DSP_SDA

DSP_RST

R686

330

T_SCL

T_SDA

R687

330

M_RCH

S-GND

M_LCH

L603 47uH

16 15 14 13 12 11 10 9

5.0V

1 2 3 4 5 6 7 8

R681

330

R652

4.7K

R682

330

R653

47K

CTRL

AMP_STBY

P602

076-0648-22

N.C

RESET

A-M_CCW

A-M_CW

SRC_CCW

SRC_CW

VOL_CCW

VOL_CW

KEY_RST

KEY_CE

KEY_CL

KEY_DI

KEY_DO

B/U 4V

LED_3

LED_2

LED_1

REMOCON

KEY-INT

SYS +5V

ACC 3.3V

22 KEY-ILL

3.3V

4.0V

5.2V

3.2V

P601

076-0648-10

F-GND

GND

VFD_CLK

VFD_DO

VFD_BLK

VFD_LAT

FILA1

FILA2

VHV

10 D/D-GND

8.0V

47.6V

J901

074-1237-69

19 CD 9V

CD 9V

REQ

16 SYS-ACC

SCL

AMP-MUTE

SDA

SPDIF

11 B/U

RESET

VDD

GND

R CH

S-GND

L CH

GND

9.6V

M_SRQ

M_SCL

M_SDA

13.9V

R654

M_RST

M_RCH

S-GND

M_LCH

3.3V

47 16V

D607 MA111

R656

100K

V_CLK

V_DO

V_BLK

V_LAT

Q609 KTC2026

Q603

KRA102S

R626

180 1/4W

3.3V

R622

180 1/4W

R623

180 1/4W

Q604

KRC103S

R632

R633

R634

R635

R636

R637

R664

R665

R666

R667

R668 330

10K

330

RESET

A_CCW

A_CW

S_CCW

S_CW

V_CCW

V_CW

K_RST

K_CE

K_CL

K_DI

K_DO

L_3

L_2

D610 MA111 L_1

REMO

R638 100

L602

K_INT

5.6uH

L601 5.6uH

2 F-GND

F-GND

FILA1

FILA2

VHV

D/D-GND

To page 19

Main PWB 2/3

To page 20

Main PWB 3/3

R697

R698

K_INT

3.3V

L_1

L_2

L_3

4.7V

4.8V

3.3V

K_DO

K_DI

K_CL

K_CE

K_RST

RESET ON:0.3V

RESET OFF:3.3V

CAR

WIRED

REMOCON

REMOCON

F-GND

REMOCON

VFD

_DO

VFD

CLK

CTRL

INT-AMP_REM

KEY-INT

5V_REM

CD_9V_REM

MECH_ACC

CLK-TEST

INIT1

INIT2

LED1

LED2

LED3

BVSS

BVDD

KEY_DI

KEY_DO

KEY_CL

KEY_CE

F_TX

NO KEY: 3.2V

EJECT:0V

POWER:0.4V

LOAD:2.0V

ACC ON(POW ON):3.3V

ACC OFF:0V

ACC ON(POW ON):3.3V

ACC OFF:0V

IC601

UPD703272YGC-307

DSP_SCL

DSP_SDA

ACC ON(POW ON):5.2V

ACC OFF:0V

B/U ON:5.6V

B/U OFF:0V

ACC_DET

B/U_DET1

CATS_DET

ILL_DET

ILL ON:0V

ILL OFF:3.6V

RESET ON:0.3V

RESET OFF:3.3V

XT2

XT1

RESET

GND

REGC

VDD

FLASH_MODE

AMP_MUTE

PHONE ON:3.2V

PHONE OFF:0V

MUTE ON:0V

MUTE OFF:3.3V

AVREF1

LINE/SYS_MUTE

SYS_ACC

AVSS

AVREF0

KEY

RESET

A-ANT REM

R662

100K

D608

MA111 R648 10K

R649 4.7K

Q606

KTA1504S

R655 10K

8.0V

Q610

KTA1298

8.0V

R611

10K

1.5K 1/4W

R674

0.33F 5.5V

Q213

RN2427

3.3V

Q214

RN2427

F_RX

DSP_SCL

DSP_SDA

3.3V

R661

10K

3.3V

R663 0

X602

X601

32.768KHz

3.14MHz

R660

10K

3.3V

C607

4.7

10V

TAN

AMP_MUTE

SYS_MUTE

D215 MA111

IC605 BR93L46F-W

3.2V

VCC

GND

CLK

C609 22p

C608 18p

C628

0.022

Q212 2SB1237

D216

MA111

IC203

AN77L04M

4.0V

R230

R624

5.6K

10 16V

ACC ON:3.3V/OFF:0V

3.3V

5 4

IC604

S-80820CNMC

1 2 3

0.33F 5.5V

D214 MA113

3.3V

22 6.3V

5.6V

D213

MA111

Q203

KTC2026

R206

220

Q618 KRA102S

5 4

IC603

BD4843G

1 2 3

5.8V

- 18 WXZ468RMP

8 7 6 5

IC602

HA12187FP

2 3 4

D609

MA4068M

Q608

KRC102S

R647

15K

D603

HZS6A2L

J601

074-1194-00

4 5

9 10

R603

1/4W

No. Description

1 GND

2 BACK UP

3 L-CH(+)

4 N.C.

5 N.C.

6 BUS(+)

7 R-CH(+)

8 R-CH(-)

9 SYS-ACC

10 BUS(-)

11 L-CH(-)

12 ILLUMI

13 N.C.

Main PWB 3/3

To page 20

BUS 14V

BUS AUDIO R+

BUS AUDIO R-

BUS AUDIO L-

BUS AUDIO L+

2 ACC 5V

2 ACC 3.3V

ILL ON:13.9V

ILL OFF:0V

2 AUDIO 9V

SP_A

SP_B

SP_C

SP_DATA

ILL ON:0V

ILL OFF:13.8V

D604

MA729

PHONE

Q601 KTA1504S

33 25V

R613 47K

ILL ON:14.0V

ILL OFF:0V

ILL ON:13.4V

ILL OFF:0V

R610

4.7K

D605

MA8047M

D606

MA111

R615

10K

D601

MA111

DD_REM

SYS_MUTE

AMP_MUTE

AMP_STBY

IC201 HA13168

1 2 3 5 6 7 8 9 10 11 12 13 14 15

AMP_REM

CTRL

R201

68K

SPAN-A

SPAN-B

SPAN-C

SPAN-DATA

To page 19

Main PWB 2/3

To page 20

Main PWB 3/3

3 ILL

3 PHONE

3 DD_REM

SYS-MUTE

AMP-MUTE

AMP-STBY

3 B/U 14V

B/U 5.7V

ACC

3 AUDIO 9V

REM

GND

AUDIO 9V

GND

To page 19

Main PWB 2/3

Main PWB(B2) section 2/3

BL1

CCC-TUNER

880-2150A

To page 20

Main PWB 3/3

ANT1

150p

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

100 10V

6.8uH

T_RDDA

T_RDCL

T_SDA

T_SCL

DSP_RST

24 23 22 21 20 19 18 17 16 15 14 13

C322

0.1

C323

0.1

1 2 3 4 5 6 7 8 9 10 11 12

L302

R333

820

L301

PROUT

C308 1

C576

0.1

R560

24K

VOUTR

INPR

8 7 6 5

1 2 3 4

PLOUT

R562

24K

INPL

VOUTL

C579

10 16V

R584

8.2K

R335 820

L304

R336 220 L305

38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20

D VDD _BYP_C

A VDD _BYP_C

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

C506

270p

8 7 6 5

1 2 3 4

C507

270p

C504

2200p

C505

2200p

R341

330

R340

330

FIL302

FIL303

DSP_SDA

DSP_SCL

C567

2.2 50V

R571

8.9V

C568

2.2 50V

R572

8 7 6 5

R573

3.9K

C571

10 16V

D552

MA111

R574

3.9K

C569

2.2 50V

R575

1 2 3 4

R578

3.9K

C570

2.2 50V

R576

C572

10 16V

D554

MA111

DSP_SCL

DSP_SDA

DSP_RST

8.6V

MA729

8.9V

5.0V

3.2V

C575

0.1

BUS_R

C555

2.2 50V

8.9V

8 7 6 5

R551

56K(F)

C551

10 16V

R552

56K(F)

TUN_RDDA

TUN_RDCL

TUN_SDA

TUN_SCL

DSP_SCL

DSP_SDA

DSP_RESET

1 AUDIO 9V

ACC 5V

ACC 3.3V

GND

BUS AUDIO R+

BUS AUDIO R-

To page 18

Main PWB 1/3

R427 100

R429 100

BUS_L

CDM_R

C556

2.2

50V

CDM_L

AUX_R

AUX_L

1 2 3 4

D505

D506

D507

MA729

C16

0.047

R553

56K(F)

C553

10 16V

R554 C554

56K(F) 10 16V

R559

220

C557

2.2 50V

R561

220

C558

2.2 50V

1 BUS AUDIO L-

BUS AUDIO L+

CDM_RCH

1 CDM_S-GND

1 CDM_LCH

AUX_RCH

AUX_LCH

VREF

T-GND

S-GND

To page 20

Main PWB 3/3

F-GND

LEVEL_IN_R

LEVEL_IN_L

SP_A

SP_B

SP_C

SP_DATA

SPAN-A

SPAN-B

SPAN-C

SPAN-DATA

To page 18

Main PWB 1/3

L401

1uH

18 17 16 15 14 13 12 11 10

IC401

BA3834F

1 2 3 4 5 6 7 8 9

5.0V

- 19 WXZ468RMP

Main PWB(B2) section 3/3

AUX_RCH

AUX_LCH

VREF

To page 19

Main PWB 2/3

S-GND

T-GND

GND

F-GND

AUDIO 9V

AMP-STBY

B/U 5.7V

SYS-MUTE 1

To page 18

Main PWB 1/3

AMP-MUTE

PHONE

ACC

REM

ILL

BUS 14V

B/U 14V

R448

220

R447

220

R450

220

R449

220

4.6V

L521

C542

47uH

10 16V

R523

330

8 7 6 5

1 2 3 4

L520

8.9V

D502

MA111

8.3V

5.8V

D501

MA111

5.2V

MUTE ON:0V/OFF:3.3V

R538

R537

3.3K

8.2K

Q501

KRC106S

Q502

KRA106S

MUTE ON:1.7V

MUTE OFF:0V

PHONE

ACC

REM

ILL

D504

HZU7.5B2

13.3V

6.0V

R536

C416

2.2 50V

8.9V

R414

56K(F)

C412

10 16V

C417

2.2 50V

8 7 6 5

R415

56K(F)

C413

10 16V

1 2 3 4

L403

L404

L405

L406

L407

L408

L409

L410

RCA-PIN-CORD

855-5535-50

F-R

F-L

S-GND

R-R

R-L

AUX-R GND

AUX-R

AUX-L GND

AUX-L

R ch

FRONT

L ch

R ch

REAR

L ch

R ch

AUX IN

L ch

LINE OUT

R416

56K(F)

C414

C415

10 16V

R417

56K(F)

C454

10 16V

R459

330

C453

10 16V

R460

330

C455

10 16V

R461

330

C456

10 16V

R462

330

R464

MUTE ON:0.7V

MUTE OFF:0V

R465

MUTE ON:0.7V

MUTE OFF:0V

Q208

2SB1243

47.6V

13.9V

IC202

DC-DC

CONVERTER

L201

220uH

13.9V

Q205

2SB1243

F201

1.3A

L202

100uH

1 2 3 4 5 6 7

R208

560

1/4W

10K 1/4W

46.9V

0.1V

D210

MA113

2.0V

D206

MA111

11.4V

R216

D201

MA4180

DD_REM

VHV

D/D-GND

To page 18

Main PWB 1/3

FILA2

FILA1

R101

10K

C102

C104

C105

C103

0.47

R112

R113

R114

R115

IC101

TB2906HQ

C109

1 50V

R102

27K

C116

1000p

POW ON:3.4V

POW OFF:0V

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

13.9V

RL-

J101

074-1214-00

PHONE

ACC

11.6V

D209

MA111

12.1V

R219

18K 1/4W

14.1V

REM

ILL

13.3V

ILL ON:14.1V

ILL OFF:0V

14.0V

C125

1000p

RL+

FL-

FL+

FR+

FR-

RR+

RR-

C126

1000p

C127

1000p

C128

1000p

C129

1000p

C130

1000p

C131

1000p

C132

1000p

14.0V

D203

1N5404

No. Description

1 SP R/L(+)

3 SP F/L(-)

5 SP F/L(+)

7 SP F/R(+)

9 SP F/R(-)

11 SP R/R(+)

13 SP R/R(-)

15 BACK UP

No. Description

2 SP R/L(-)

4 PHONE INT

6 ACC

8 N.C

10 REMOTE

12 ILLUMI

14 BACK UP(BUS)

16 GND

L101

- 20 WXZ468RMP

Clarion Co., Ltd.

50 Kamitoda, Toda-shi, Saitama 335-8511 Japan

Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan

Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703

Published by Service Dept.

Jan.2006

Printed in Japan

Service Manual

In Dash 6disc CD Auto Changer

Mechanism(GI-X)

Model

929-0371-80

EXPLANATION OF IC

051-3364-90 NJU7771F15-TE2 1.5V Positive Voltage Regurator

OUTPUT

VDD

GND

Control (H= On)

Ground

N.C.

5 C.T.

4 N.C.

Vref

VDD

5 Vin

4 Vout

051-5452-90 BD5235G-TR

Precision Vlotage Down Detector 3.5V

GND

Vout

Terminal description pin 1: OUTPUT pin 2: VDD pin 3: GND pin 4: N.C.

pin 5: C.T.

: N channel open drain output.

This terminal will output L, if the voltage of

VDD becomes lower than the setting voltage.

: Positive supply voltage.

: Ground.

: Not in use.

: Delay time capacitor.

- M1 -

051-6711-20 TC94A34FG-004

Terminal Description pin 1: VDDP pin 2: Reset pin 3: Standby pin 4: MiCS pin 5: MiLP pin 6: MiDio pin 7: MiCK pin 8: MiACK pin 9: VDDT pin 10: VSS pin 11: SDo 0 pin 12: BCKo pin 13: LRCKo pin 14: SDi 0 pin 15: BCKi A pin 16: LRCKi A pin 17: Data pin 18: SBSY pin 19: SFSY pin 20: TXo pin 21: VDD pin 22: CLOCK pin 23: VSS pin 24: io 0 pin 25: io 1 pin 26: io 2 pin 27: io 3 pin 28: Pio 4 pin 29: Pio 5 pin 30: Pio 6 pin 31: Pio 7 pin 32: WE pin 33: RAS pin 34: CAS pin 35: OE pin 36: Po 11 pin 37: Po 10

CD-ROM/MP3/WMA Decoder

: - : Positive voltage supply.

: IN : Reset input.

: IN : Standby input.

: IN : Microcomputer I/F. Chip select input.

: IN : Microcomputer I/F. Latch pulse input.

:I/O: Microcomputer I/F. I2C-SDA.

: IN : Microcomputer I/F. Clock pulse input.

: O : Microcomputer I/F. Acknowledge output.

: - : Positive voltage supply.

: - : Ground.

: O : Audio I/F. Serial data output.

: O : Audio I/F. Bit clock output.

: O : Audio I/F. LR clock output.

: IN : Audio I/F. Serial data input.

: IN : Audio I/F. Bit clock input.

: IN : Audio I/F. LR clock input.

: IN : Sub Code I/F. The data input.

: IN : Sub Code I/F. Block sync.

: IN : Sub Code I/F. Frame sync.

: O : SPD I/F. Transmission terminal.

: - : Positive voltage supply.

:I/O: Sub Code I/F Clock pulse input/output.

: - : Ground.

:I/O: SRAM/DRAM I/F. Parallel data input/output.

:I/O: General-purpose I/O terminal. Parallel data input/output.

: O : SRAM/DRAM I/F. Write enable.

: O : DRAM I/F. RAS output.

: O : DRAM I/F. CAS output.

: O : SRAM/DRAM I/F. Output enable.

: O : General-purpose output terminal.

929-0371-80

pin 38: Po 9 pin 39: Po 8 pin 40: VDDM pin 41: SRMSTB pin 42: VDDT pin 43: AD 10 pin 44: AD 9 pin 45: AD 8 pin 46: AD 7 pin 47: AD 6 pin 48: AD 5 pin 49: AD 4 pin 50: AD 3 pin 51: AD 2 pin 52: AD 1 pin 53: AD 0 pin 54: VSS pin 55: VDD pin 56: CKo

: Po 13 pin 57: VDDX pin 58: Xo pin 59: Xi pin 60: VSSX pin 61: TEST pin 62: MiMD pin 63: VSSP pin 64: VCOi

: O : General-purpose output terminal.

: - : Positive voltage supply.

: IN : Internal SRAM I/F. Standby input.

: - : Positive voltage supply.

: O : SRAM/FRAM I/F. Address output.

: - : Ground.

: - : Positive voltage supply.

: O : Clock output.

: O : General-purpose output terminal.

: - : Positive voltage supply.

: O : Crystal connection.

: IN : Crystal connection.

: - : Ground.

: IN : H = Test.

: IN : H = I2C, L = Normal.

: - : Ground.

: O : Control voltage output for VCO.

051-9318-10 GLT4160L04P-60TC

Terminal Description pin 1 : VCC pin 2 : DQ 0 pin 3 : DQ 1 pin 4 : WE_ pin 5 : RAS_ pin 6 : NU pin 7 : NEX pin 8 : A 10 pin 9 : A 0 pin 10: A 1 pin 11: A 2 pin 12: A 3 pin 13: VCC pin 14: VSS pin 15: A 4 pin 16: A 5 pin 17: A 6 pin 18: A 7 pin 19: A 8 pin 20: NEX pin 21: A 9 pin 22: OE_ pin 23: CAS_ pin 24: DQ 2 pin 25: DQ 3 pin 26: VSS

16M bit Dynamic RAM

: Positive supply voltage.

: Data input / output.

: Write enable.

: Row address strobe.

: Not in use.

: No existence.

: Address input.

: Positive supply voltage.

: Ground.

: Address input.

: No existence.

: Address input.

: Output enable.

: Column address strobe.

: Data input / output.

: Ground.

052-5070-91 T5AF4 Mechanism Controller pin 4: LO CW pin 5: LO CCW pin 6: A MUTE pin 7: De-emphasis pin 8: E-EJ pin 9: P ON 1 pin 10: NU pin 11: P ON 3 pin 12: NU pin 13: NU pin 14: NU pin 15: NU pin 16: NU pin 17: NU pin 18: DSP SO pin 19: DSP SI pin 20: DSP SCK pin 21: FL TX pin 22: FL RX pin 23: SW 9V pin 24: PULL UP pin 25: VCC pin 26: X out pin 27: VSS pin 28: X in pin 29: PULL UP pin 30: RESET pin 31: TIME pin 32: NU pin 33: NC pin 34: NC pin 35: BU DET pin 36: SW 5 pin 37: SBSY

TerminalDescription pin 1: Vref L pin pin

2: A VSS

3: A VCC

: - : Reference voltage.

: - : Negative voltage supply for analog section.

: - : Positive voltage supply for the internal analog section.

: O : Loading motor control signal output.

: O : The audio mute signal output.

: IN : De-emphasis ON command input.

: IN : Emergency Eject input.

: O : Power ON signal output.

: - : Not in use.

: O : Power ON signal output.

: - : Not in use.

: O : Serial data output to the DSP IC.

: IN : Serial data input from the DSP IC.

: O : The clock pulse output to DSP IC.

: O : The serial data output for flash memory.

: IN : The serial data input for flash memory.

: O : 9V power supply control.

: IN : PULL UP

: - : Positive voltage supply.

: O : Crystal connection.

: - : Negative voltage supply.

: IN : Crystal connection.

: IN : PULL UP

: IN : Reset signal input.

: O : For Time base.

: - : Not in use.

: O : Not in use.

: IN : Backup detection signal input.

: IN : The switch signal input.

: IN : Sub code block synchronous signal detection input.

pin 38: PON 2 pin 39: MODE CW pin 40: MODE CCW pin 41: U/D CW

: O : Power ON signal output.

: O : Mode motor control.

: O : Holder control.

pin 42: U/D CCW pin 43: ALE

: O : Holder control.

: O : The address latch enable output.

pin 44: DR MUTE : O : Drive mute signal output to the CD IC.

pin 45: SRAM STNDB : O : SRAM standby signal output.

pin 46: DSP RESET pin 47: DSP CS pin 48: DSP LAT pin 49: DSP ACK pin 50: LIMIT pin 51: EEP CS pin 52: EEP SK pin 53: EEP DI pin 54: EEP DO pin 55: HSSW pin 56: HSSW 2

: O : Reset signal output to the DSP IC.

: O : Chip select signal output to the DSP.

: O : The latch pulse output to DSP IC.

: IN : DSP acknowledge.

: IN : Inside limit switch signal input.

: O : The chip select output to EEP-ROM.

: O : The clock pulse output to the EEP-ROM.

: IN : The serial data input from the EEP-ROM.

: O : The serial data output to the EEP-ROM.

: IN : It is used at the jitter measurement (the speed is 2X, shock proof is through).

: IN : It is used at the jitter measurement (the speed is 1X, shock proof is through).

: IN : DSP request input.

pin 57: DSP REQ pin 58: DSP STNDB pin 59: NU pin 60: NU pin 61: BUC CLOCK pin 62: VSS pin 63: NMI pin 64: VCC

: O : DSP standby output.

: - : Not in use.

: O : CD IC clock pulse output.

: - : Negative voltage supply.

: IN : Connect to VDD via a resistor.

: - : Positive voltage supply.

929-0371-80 - M2-

pin 65: BUS 0 pin 66: BUS 1 pin 67: BUS 2 pin 68: BUS 3 pin 69: CCE pin 70: CD RESET pin 71: T DATA pin 72: T CLK pin 73: T CLR pin 74: NU pin 75: NU pin 76: NU pin 77: NU pin 78: FL BOOT pin 79: TEST 1 pin 80: TEST 2 pin 81: TEST 3 pin 82: TEST 4 pin 83: REQ O pin 84: I2C SDA pin 85: I2C SCL pin 86: ACC DET pin 87: NU pin 88: SW 1 pin 89: VCC pin 90: SW 2 pin 91: VSS pin 92: SW 3 pin 93: SW 4 pin 94: NU pin 95: PT 1 pin 96: PT 2 pin 97: PT 3 pin 98: PT 4 pin 99: PT 5 pin100: Vref H

:I/O: CD IC Data input / output.

: O : The chip enable signal output.

: O : The reset pulse output to the CD IC.

: O : The display data output for the test mode indication.

: O : The test clock output.

: O : The clear signal output for the test mode indication.

: - : Not in use.

: IN : Flash memory control.

: IN : For the test.

: O : Transmit request signal output.

:I/O: I2C serial data input/output.

:I/O: I2C serial clock input/output.

: IN : ACC detection signal input.

: - : Not in use.

: IN : The switch signal input.

: - : Positive voltage supply.

: IN : The switch signal input.

: - : Negative voltage supply.

: IN : The switch signal input.

: - : Not in use.

: IN : The photo sensor signal input.

: - : Reference voltage.

- M3 929-0371-80

DISASSEMBLY

How to remove "CD-PWB-ASSY"

1. Add +5V to "U+" terminal of UD-MOTOR-ASSY,then

SIDE-P-ASSY-F moves outside of CD-PWB.

2. Release four FPCs.

3. Remove three screws

4. Remove the washer.

5. Remove SW-H-PLATE and SW-LINK, and remove CD-

PWB-ASSY.

How to remove "DISCHOLDER UNIT"

1. Remove eight screws.

2. Remove the FPC.

SIDE-P-ASSY-F

CD-PWB-ASSY

* When assembling, match

SW LINK to three switches.

SW-LINK

Switches

3. Remove UPPER UNIT ASSY.

4. Remove two C-RINGs, and remove DISCHOLDER

UNIT.

DISCHOLDER UNIT

929-0371-80 - M4-

How to remove "N-DRIVE UNIT"

1. Remove the screw and DRIVE SPRING-A.

2. Rotate N-DRIVE UNIT internally.

3. Remove the washer, and remove N-DRIVE UNIT.

N-DRIVE UNIT

How to remove "LO-MOTOR-S-ASSY"

1. Remove two screws and DRIVE CHASSIS-B.

2. Remove the screw of the bottom side.

3. Remove the solder of SENSOR-L-FPC, and remove LO-

MOTOR-S-ASSY.

DRIVE CHASSIS-B

SENSOR-L-FPC

LO-MOTOR-S-ASSY

How to remove "M-MTR SUB ASSY"

1. Remove two screws, and remove M-MTR SUB ASSY.

M-MTR SUB ASSY

How to remove "UD-MOTOR-ASSY"

1. Remove the screw of the bottom side, and remove UD-

MOTOR-ASSY.

UD-MOTOR-ASSY

- M5 929-0371-80

OPERATION

Drive Unit

S5 of SENSOR-U-FPC (Sutter)

S4 of CD-PWB (Holder)

Shutter

Function of Mechanism

[DISC HOLDER]

Six holders.

(Related motor:UP/DW-Motor)

[DRIVE UNIT]

Chukking of a play disc.

(Related Motor:Mode motor)

[LOADING ROLLER]

Disk is stored/ejected by rotation.

(Related Motor:Laoding motor)

[SHUTTER]

Shutter at disc insertion.

(Related Motor:Mode Motor)

Function of Motors

[MOT1 LOADING MOTOR]

Rotation of loading roller.

(Related Sensor:PT1,2,3,Q1)

[MOT2 MODE MOTOR]

Rotation of mode plate.

Chukking disc.

Opening/closing holder.

Movement of loading/ejecting roller.

Opening/closing shutter.

(Related Sensor:S1,2,3)

[MOT3 UP/DW-MOTOR]

Going up and down of disc holder.

Selection of disc holder.

(Related Sensor:S4,IC10)

Discholder

MOT2 (Mode Motor)

S1 of CD-PWB (Mode Plate)

S2 of CD-PWB (Mode Plate)

S3 of CD-PWB (Mode Plate)

MOT3 (UP/DW-Motor)

MOT1 (Loading Motor)

Loading Roller

PT3 of SENSOR-L-FPC

PT2 of SENSOR-L-FPC

PT1 of SENSOR-L-FPC

IC10 of CD PWB

Q1 of CD PWB

Function of Switches

[S1,2,3]

Detect a home position of mode plate.

Detect mode plate position by combination of on and off.

[S4]

Detection of initial position of holder.

[S5]

Initial position:S4-ON,IC10-bright.

Opening/closing detection of shutter.

OFF:Close, ON:Open

Function of Photo sensors

[PT1]

Detection of start loading and passing of disc.

Bright:no DISC, Dark:DISC

[PT2]

Detection of finish eject and passing of disc.

Bright:no DISC, Dark:DISC

[PT3]

Detection of store and passing of disc.

Bright:no DISC, Dark:DISC

[Q1]

Detection of passing of disc.

Bright:no DISC, Dark:DISC

[IC10]

Detection of holder position

929-0371-80 - M6-

EXPLODED VIEW/PARTS LIST

Main section

17 to B1

8 to B2

3 to C1 to A6

C2 to A2

13 to A7 to A3 to A4

* 30

C4 to A5

* 32

* 31

37 to C4 to C3 to C2

10 to D3

A2 to

A5 to

A7 to D3

23 16

33 34

* 28

21 14

25 23

* Do not reuse the following parts.

(No.24,25,28,29,30,31,32)

NO.

PART NO.

DESCRIPTION

966-1756-24 LOWER UNIT ASSY

966-0667-21 DISC STP-ASSY L

966-0668-22 DH-SEL-ASSY S

966-0669-22 DH-SEL-ASSY R

966-0670-22 DS-SP-ASSY L

966-1760-21 DS-SP-ASSY R

966-0672-21 REAR-P-ASSY

966-1753-91 N-DRIVE-CH UNIT

966-1764-21 UPPER UNIT ASSY

HBS-566-100 DISC HOLDER UNIT

966-1771-21 SLIDE-P-ASSY F

966-0709-21 SLIDE-P-ASSY

HBS-564-100 CD-PWB-ASSY

620-1640-20 SW-H-PLATE

620-1778-20 GAP PLATE F

620-1662-21 GAP PLATE R

620-1685-21 DS-PLATE L

620-1686-20 DS-PLATE R

621-1760-21 DISC STOPPER R

Q'TY

- M7 -

NO.

PART NO.

621-1636-24

621-1765-20 UD-GEAR-D

621-1715-20 FPC-STOPPER

716-1850-01

716-1850-02 SCREW(M2.0x2.0)

716-1851-02 SCREW(M2.0x3.0)

716-3450-00 SCREW(M1.7x2.0)

716-3451-01 SCREW(M1.7x2.5)

746-0761-00

744-0045-01 C-RING

347-7271-00 FPC SHEET

347-7275-00 PROTECT SHEET

347-7276-00 FPC-SHEET C

800-4921-60

802-4921-60

345-5824-00

621-1763-20

716-1859-01

DESCRIPTION

SW LINK

SCREW(M2.0x2.0)

WASHER

VINYL-COAT-WIRE

RUBBER PART

LOADING GUIDE B

IT SCREW(M1.7 x 2)

929-0371-80

Q'TY

Lower unit assy section

15 to A1

6 to A2

15 to A3

5 to

A4 to A5

4 to A6 to A7

NO.

PART NO.

DESCRIPTION

966-1757-21 LOWER-C-ASSY

966-0658-21 DH-SP-ASSY A

966-1758-20 DS-SP-ASSY A

966-0660-22 DH-SP-ASSY S

966-0661-22 DH-SP-ASSY R

966-0677-23 D-SHT PL-B-ASSY

966-0659-21 DH-SP-ASSY B

966-1759-00 DS-SP-ASSY B

HBS-546-100 M-MTR SUB ASSY

HBS-568-100 UD-MOTOR-ASSY

929-0371-80

Q'TY

NO.

PART NO.

DESCRIPTION

620-1771-22 CAM GEAR

620-1624-24 GEAR COVER

621-0732-21 M-GEAR B

621-0733-20 M-GEAR C

716-1850-01 SCREW(M2.0x2.0)

716-3451-01 SCREW(M1.7x2.5)

746-0761-00 WASHER

746-0768-00 WASHER

750-6756-00 SW-L-SPRING

- M8-

Q'TY

[ Grease Point ]

* Grease: SANKOL FG-87HSR

Put grease on the surface

Put grease on the reverse side

Put grease on the both sides

Put grease on the edge

1 2

4 5 6

- M9 -

929-0371-80

N-Drive-CH unit section

* 20

8 to A1 to A2

4-1 to B1

* 18

19 5

A4 11

16 21

B1 to A3 to A4

* Do not reuse the following parts.

(No.17,18,19,20)

NO.

4-1

PART NO.

622-1743-20

DESCRIPTION

HBS-565-100 N-DRIVE UNIT

HBS-567-100 LOADING-U-ASSY

HBS-556-100 LO-MOTOR-S-ASSY

HBS-552-100 L-SENSOR-S-ASSY

----------SENSOR-L-FPC

966-0676-20 D-SHT LK-A-ASSY

966-1755-00 DRIVE-CH A ASSY

620-1681-21 DRIVE CHASSIS B

620-1672-21 DR-SUPPORT-PL

620-1680-20 D-SHIFT COVER

D-SHIFT ROLLER B

929-0371-80

Q'TY

NO.

- M10-

PART NO.

DESCRIPTION

716-3450-00 SCREW(M1.7x2.0)

716-3459-01 SCREW(M1.7x2.0)

750-6761-20 DRIVE SPRING A

345-5868-00 RUBBER PART

620-1651-20 S-PWB-PLATE

750-6754-20 LO-ES-SPRING B

345-5424-01 SEN-FPC GUIDE

716-1859-01 SCREW(M1.7x2.0)

744-0039-00 E-RING

746-0870-00 WASHER

716-3538-00 SCREW(M1.7x2.0)

Q'TY

[ Grease Point ]

* Grease A: SANKOL FG-87HSR

* Grease B: SANKOL CFD-006MBL

Put grease on the surface

Put grease on the reverse side

Put grease on the both sides

Put grease on the edge

Surface of PIN

Surface of Spring

- M11 929-0371-80

Upper unit assy section

to A1

7-1 to A2

* Do not reuse the following parts.

(No.7,8,10)

7-1

NO.

PART NO.

966-1761-21

966-1765-20

DESCRIPTION

UPPER-CHA-ASSY

LO-SHIFT A ASSY

966-0700-22 LO-SHIFT B ASSY

966-0701-21 LO-SHIFT ASSY

966-1766-20 SHUTTER-PL-ASSY

966-1763-20 SHUTTER ASSY

HBS-553-100 U-SENSOR-S-ASSY

----------SENSOR-U-FPC

347-7272-00 RATTLE SHEET

750-6755-21 SHUTTER SPRING

746-0870-00 WASHER

Q'TY

[ Grease Point ]

* Grease: SANKOL FG-87HSR

Put grease on the surface

Put grease on the reverse side

Put grease on the both sides

Put grease on the edge

3 4

929-0371-80 - M12-

ELECTRICAL PARTS LIST

CD PWB(BM1) section

REF No. PART No.

DESCRIPTION

C63

C64

C65

C66

C67

C68

C70

C71

C72

C55

C56

C57

C59

C60

C61

C62

C46

C47

C48

C49

C50

C51

C52

C53

C54

C38

C39

C40

C42

C43

C44

C45

C28

C29

C30

C31

C32

C33

C34

C35

C15

C20

C21

C22

C23

C24

C25

C26

C27

C10

C11

C12

C13

C14

042-0672-00 25V 47uF TA

166-1011-50 100pF CH

168-1042-78 16V 0.1uF

178-1052-78 1uF

042-0671-01 10V 47uF TA

168-1045-56 0.1uF Z

168-1032-55 0.01uF K

168-1045-56 0.1uF Z

178-1052-78 1uF

168-1045-56 0.1uF Z

178-1052-78 1uF

042-0671-01 10V 47uF TA

168-1032-55 0.01uF K

178-1052-78 1uF

168-1042-78 16V 0.1uF

178-1052-78 1uF

168-1045-56 0.1uF Z

042-0671-01 10V 47uF TA

168-1042-78 16V 0.1uF

168-1045-56 0.1uF Z

168-4732-78 0.047uF K

166-4701-50 47pF CH

168-4732-78 0.047uF K

166-4711-50 470pF CH

168-1532-55 0.015uF K

166-4711-50 470pF CH

168-1045-56 0.1uF Z

168-6822-55 6800pF K

168-1032-55 0.01uF K

168-3332-78 0.033uF K

168-4722-55 4700pF K

168-1042-78 16V 0.1uF

168-1045-56 0.1uF Z

168-1532-55 0.015uF K

168-1045-56 0.1uF Z

168-1522-55 1500pF K

168-1045-56 0.1uF Z

166-6811-50 680pF

166-6801-50 68pF CH

178-1052-78 1uF

042-0671-01 10V 47uF TA

178-1052-78 1uF

168-1042-78 16V 0.1uF

178-1052-78 1uF

042-0671-01 10V 47uF TA

168-1042-78 16V 0.1uF

168-1045-56 0.1uF Z

178-1052-78 1uF

168-1032-55 0.01uF K

168-1045-56 0.1uF Z

Sensor-L-PFC(BM2) section

REF No. PART No.

DESCRIPTION

PT1 060-0252-01 PT14850F

Sensor-U-PFC(BM3) section

REF No. PART No.

DESCRIPTION

LED1

LED2

001-7077-00 GL4804

REF No. PART No.

DESCRIPTION

R10

R11

R12

R13

R14

R15

R16

Q20

Q10

Q11

Q12

IC12

IC3

IC4

IC5

IC6

IC8

IC9

IC10

IC11

IC1

IC2

C73

C74

C75

C81

C82

C83

C85

178-1052-78 1uF

168-1045-56 0.1uF Z

168-2222-55 2200pF K

166-1007-50 10pF CH

178-1052-78 1uF

C86

C87

166-1201-50 12pF CH

042-1702-90 6.3V 100uF

C91 168-1032-55 0.01uF K

CCT1 050-0145-59 1/16W 22 ohm x4

CCT2 050-0145-54 1/16W 47k ohm x4

CCT3 050-0145-54 1/16W 47k ohm x4

CCT4 050-0145-55 1/16W 10k ohm x4

001-4301-14 HZU 3.0B1

001-0529-14 MA8030-L

001-0367-91 1SS226

001-4301-16 HZU 3.3B1

004-0529-16 MA8033-L

001-4301-18 HZU 3.6B1

001-0529-18 MA8036-L

051-6399-00 TC94A15F

052-5070-91 T5AF4

051-6711-20 TC94A34FG-004

051-6060-08 BD7961FM-E2

051-5452-90 BD5235G-TR

051-9318-10 GLT4160L04P-60TC

051-9402-78 BR93L56RFVM-W

051-6072-08 BD7931FE2

051-5833-00 GP1S093HCZ

051-3364-90 NJU7771F15

074-1237-69 19PIN

074-1201-65 15P

074-1138-56 6P

074-1100-61 SOCKET 11P

074-1201-61 11P SOCKET

060-0252-01 PT4850F

125-0021-91 DTA114EUA

198-3018-00 2SK3018

131-1188-50 2SB1188PQR

125-2027-91 DTC114EUA

131-1427-00 2SB1427

131-1188-50 2SB1188PQR

125-2027-91 DTC114EUA

125-0021-91 DTA114EUA

125-2027-91 DTC114EUA

131-1427-00 2SB1427

119-4731-15 1/10W 47k ohm

119-2211-15 1/10W 220 ohm

119-1041-15 1/10W 100k ohm

119-4731-15 1/10W 47k ohm

119-2211-15 1/10W 220 ohm

032-0140-16 1/10W 180k ohm F

032-0140-96 1/10W 120k ohm F

119-2231-15 1/10W 22k ohm

119-4711-15 1/10W 470 ohm

119-2221-15 1/10W 2.2k ohm

119-1031-15 1/10W 10k ohm

119-0000-05 1/10W 0 ohm JW

REF No. PART No.

DESCRIPTION

R85

R86

R66

R71

R72

R73

R77

R82

R83

R56

R57

R58

R59

R60

R61

R62

R64

R65

R49

R50

R51

R52

R53

R54

R55

R40

R41

R42

R43

R44

R45

R46

R48

R31

R32

R33

R34

R35

R36

R37

R38

R39

R24

R25

R26

R27

R28

R29

R30

R17

R18

R19

R20

R21

R22

R23

119-4731-15 1/10W 47k ohm

119-2231-15 1/10W 22k ohm

119-4721-15 1/10W 4.7k ohm

119-4731-15 1/10W 47k ohm

050-0145-58 1/16W 2.2k ohm x4

119-4721-15 1/10W 4.7k ohm

117-7511-15 1/8W 750 ohm

116-3391-15 1/4W 3.3 ohm

032-0145-73 1/2W 6.8 ohm

119-1041-15 1/10W 100k ohm

119-6811-15 1/10W 680 ohm

119-1041-15 1/10W 100k ohm

119-6811-15 1/10W 680 ohm

119-1041-15 1/10W 100k ohm

117-5611-15 1/8W 560 ohm

119-1041-15 1/10W 100k ohm

119-3321-15 1/10W 3.3k ohm

119-1051-15 1/10W 1M ohm

119-0000-05 1/10W 0 ohm JW

119-1041-15 1/10W 100k ohm

119-5621-15 1/10W 5.6k ohm

119-4731-15 1/10W 47k ohm

119-2231-15 1/10W 22k ohm

119-8231-15 1/10W 82k ohm

119-3341-15 1/10W 330k ohm

119-2231-15 1/10W 22k ohm

116-1001-15 1/4W 10 ohm

119-1011-15 1/10W 100 ohm

119-6811-15 1/10W 680 ohm

117-7511-15 1/8W 750 ohm

116-5611-15 1/4W 560 ohm

119-1041-15 1/10W 100k ohm

116-1511-15 1/4W 150 ohm

119-4731-15 1/10W 47k ohm

119-1051-15 1/10W 1M ohm

032-0140-53 1/10W 2.2k ohm F

119-2211-15 1/10W 220 ohm

032-0140-62 1/10W 1k ohm F

119-1011-15 1/10W 100 ohm

119-0000-05 1/10W 0 ohm JW

119-1011-15 1/10W 100 ohm

119-1031-15 1/10W 10k ohm

119-1021-15 1/10W 1k ohm

119-2231-15 1/10W 22k ohm

013-7416-50 SW SPVL110200

013-7415-50 SPVG110400

061-3534-90 16.92MHz

060-1545-90 20MHz

REF No. PART No.

DESCRIPTION

PT2 060-0252-01 PT14850F

REF No. PART No.

DESCRIPTION

LED3 001-7077-00 GL4804

REF No. PART No.

DESCRIPTION

PT3 051-5833-00 GP1S093HCZ

REF No. PART No.

DESCRIPTION

S5 013-7417-50 ABC1122P161

- M13 929-0371-80

BLOCK DIAGRAM

DECORDER TC94A34FG

CD3.3V 2SB1427 Q8, Q20

929-0371-80 - M14-

CIRCUIT DIAGRAM

CD PWB(BM1) section

Sensor-L-FPC(BM2) section

Sensor-U-FPC(BM3) section

074-1237-69

CD-9V

REQ

SYS-ACC

SCL

A-MUTE

SDA

SPDIF

B/U

RESET

VDD

P-GND

R-CH

GND

L-CH

D-GND

N.C.

TEST3 1

9.0V

3.3V

3.0V

12.0V

3.3V

1.6V

3.3V

To Main PWB

DTA114EUA

47 25V TAN

TP25

RESET

R77

220

TP11

GND

TP14

VDD

3.3V

R12

22K

2SB1188

VDD

3.3V

Q20

2SB1427

3.3V

C13 1

CD3.3

6.8 1/2W

C14

47 10V TAN

4 3 2 1

IC9

BD7931FE2

C59

0.1

5 6 7 8

HZU 3.0B1

R51

680

MOT3

UP/DOWN

(V-MOTOR)

R33

R31

680

9.0V

36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

C91 0.01

3.3V

8 7 6 5

IC8

BR93L56RFVM

1 2 3 4

C86

12p

PT1

PT2

PT3

3.3V

C15

0.01

R11 120K(F)

Sensor-L-FPC(BM2)

PT1

PT2

MOT1

074-1100-61

GND

PHOT1

GND

PHOT2

LOM+

LOM-

LED4

GND

PHOT3

3.3V

PT3

MOT2

MODE

074-1201-61

LED1

LED2

LED3

LED1

GND

MO+

MO-

LED2

GND

LED3

GND

SW5

SHUTTER

Sensor-U-FPC(BM3)

1.6V

R52

750

R27

750

R35

560

MO+

MO-

PT1

PT2

LO+

LO-

Q10

DTC114EUA

R53

560 1/4W

PT4850F

3.3V

R34

R36

100K

R14

2.2K

47K

R32 100K

K E

A C

R59

150 1/4W

R37

R40 0

100K 3.3V

3.3V

VREFL

AVSS

AVCC

LOCW

LOCCW

A-MUTE

DE-EMP( OR PRODUCT MODE)

E-EJECT

PON1

PON3

3.3V

MIDIO

/MICK

TP33

FTXD

TP34

FRXD

3.3V

R25 4.7K

MIDIO(SO)

MIDIO(SI)

MICK

FTXD

FRXD

LED SW

AM1

VCC

XOUT VSS

220

20MHz

- M15 -

IC2

T5AF4

TCLR

TCLK

TDATA

/CDIC-RESET

/CCE

BUS3

BUS2

BUS1

BUS0

VCC

NMI

VSS

BUCK

3.3V

TP42 TCLK

TP40

TP38

TCLR

TDATA

/CDIC-RST

/CCE

BUS3

BUS2

BUS1

BUS0

3.3V

R20 4.7K

BUCK

DSP-STB

DSP-REQ

HSW2

HSW1

RDO

RDI

RCLK

RCE

DSP-STB

DSP-REQ

3.3V

RDO

RDI

RCLK

RCE

R41 100K

CCT3

47K x4

Q12

DTC114EUA

929-0371-80

16.92M

R39

C81

10p

C23

0.1

C27

0.047

C29

0.047

C32

470p

C30

470p

C34

6800p

2SB1188

R66

2.2K (F)

BUS0

BUS1

BUS2

BUS3

BUCK

/CCE

/CDIC-RST

C60

C20 1

BCKI

AIN

LRCKI

BCKO

AOUT

LRCKO

R71

R72

R73

CCT4 10K x4

100

3.3V

75 74 73 72 71 70 69 68 67 66 65

DVSS3

DVDD3

DVR

DVSS3

ZDET

VSS5

BUS0

BCKI

AIN

BUS1

BUS2

BUS3

BUCK

CCE

RST

VDD5

EMPHI

LRCKI

EMPH(N.C.)

BCKO

AOUT

99 LRCKO

100

DOUT

1 2 3 4 5 6 7 8

64 63 62 61 60 59 58 57 56 55

IC1

TC94A15F

54 53 52 51

LDO

RVDD3

EQSET

PNSEL

RFO

RFDCI

AGCI

INVSEL

TESTR

VMDIR

VRO

RESIN

AVDD3

RFEQO

RFRPI

RFI

FPI1

FPI2

FNI1

FNI2

FTE 50

TNI

TPI

RVSS3

MDI

R18

TP81

FTE

22K

R19 22K

3.3V

1.3V

C42

C43

3.3V

1.7V

C44

0.1

0.015

0.1

C45 1500p

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

C48

68p

C46

0.1

R48

22K

C47

680p

C49

C39

4700p

C51

47 10V TAN

C50

47 10V TAN

C33

0.1

C31

0.015

R64 2.2K (F)

C52

PON3

VDD3.3V

C75

2200p

C62

0.1

AIN

BCKI

LRCKI

AOUT

BCKO

LRCKO

R15

10K

/DSP-RESET

DSP-STB

/MICS

/MILP

MIDIO

/MICK

MIACK

VDDT

VSS

SDO

BCKO

LRCKO

SDI

BCKIA

LRCKIA

VDDP

/RESET

STANDBY

/MICS

/MILP

MIDIO

/MICK

IC3

TC94A34FG-004

3.3V

R83

10K

5 4

IC12

NJU7771

1 2 3

IC11

NJU7771

5 4

SRMSTB

VDDM

N.C.

REQ

/OE

/CAS

AIOR

VDDT

/RAS

A10R C65 C64

0.1

SRMSTB

/OE

/CAS

/RAS

DSP-REQ

DQ1

DQ2

/WE

/RAS

A10R

IC6

GLT4160L04

VCC

DQ1

DQ2

VSS

DQ4

DQ3

/WE

/RAS

/CAS

/OE

N.C.

A10R

VCC VSS

C21

C25

0.1

DQ4

DQ3

/CAS

/OE

Drive Unit

2.0V

FCS-

2.0V

4.3V

2.0V

TRK-

TRK+

FCS+

4.5V

3.3V

5.0V

4.5V

074-1201-65

GND

VREF

FCS-

TRK-

VCC

TRK+

FCS+

To Pick up

LIMIT

SP-

SP+

SL+

SL-

4.0V

5.0V

4.3V

4.5V

074-1138-56

GND

LIMIT

SP-

SP+

SL+

SL-

MOT4

SPINDLE

LIMIT

MOT5

SLED

R23

47K

R82 100

C63 0.1

PRINTED WIRING BOARD

CD PWB(BM1) section

Sensor-L-FPC(BM2) section

Sensor-U-FPC(BM3) section

Drive Unit

BLK

RED

(-)

(+)

MOT3

Up/Dw

- M16 -

CD PWB(BM1) section

SOLDER SIDE

PT2

MOT1

(+)

(-)

PT3

Sensor-U-FPC(BM3) section

929-0371-80

LED1

Shutter

To Main PWB

PT1

Sensor-L-FPC(BM2) section

CD PWB(BM1) section

COMPONENT SIDE

LED3

MOT2

Mode

(+)

LED2

(-)

BLK

RED

Caution:

COMPONENT SIDE: Parts on the component side seen from the component side are indicated.

SOLDER SIDE: Parts on the solder side seen from the solder side are indicated.

Hello! I am an AI chatbot specifically trained to assist you with the Clarion WXZ468RMP Service manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated