Service Manual
Clarion Co., Ltd.
Published by Service Dept.
298-6340-00 Feb.2006
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan
Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan
Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703
Printed in Japan
Service Manual
2-DIN 6-disc
CD/MP3/WMA Receiver
/ CeNET Control
Model
(PE-2758E)
SPECIFICATIONS
Radio section
Tuning system:
Receive range:
This product is a lead free model.
Lead free solder is used in PWB stamped LF mark.
Please keep the following conditions when you repair.
1. Use lead free solder.
* Koki's lead free solder S3X-55M 0.6mm
(CLARION Parts No.642-0231-01)
* Koki's lead free solder S3X-55M 1.0mm
(CLARION Parts No.642-0231-02)
2. Use a nitrogen solder system.
3. Do not use "General solder" and "Lead free solder"
together.
CD player section
System:
Usable discs:
Frequency response:
Signal to noise ratio:
Dynamic range:
Harmonic distortion:
Channel separation:
MP3/WMA mode:
NOTES
*
*
*
*
*
*
*
PLL frequency synthesizer system
FM 87.5MHz to 108MHz
(0.05MHz steps)
MW 531kHz to 1,602kHz
(9kHz steps)
LW 153kHz to 279kHz
(3kHz steps)
As for this model, CCC-TUNER is used.
When you exchange it due to the tuner pack (BL1:8802150A) trouble, it is necessary to adjust for S-meter etc.
Special JIG is necessary for an accurate adjustment.
The procedure document for the exclusive use jig is appended to it.
Use only compact discs bearing the
or
mark.
Some CDs recorded in CD-R/CD-RW mode may not be
usable.
This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a
license from MSLGP.
and
logo are trademarks
or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
We cannot supply PWB with component parts in principle. When a circuit on PWB has failure, please repair it
by component parts base. Parts which are not mentioned
in service manual are not supplied.
Specifications and design are subject to change without
notice for further improvement.
-1-
Compact disc digital audio system
Compact disc
10Hz to 20kHz(+/-1dB)
90dB(1kHz)
90dB(1kHz)
0.01%
75dB(1kHz)
MP3 ; Sampling rate 11.025kHz 48kHz
Bit rate : 8kbps - 320kbps / VBR
WMA;Bit rate;48kbps-192kbps/VBR
Logical format(File system);
ISO9660 level 1, 2 or JOLIET or
Romeo
Audio amplifier section
Output power:
27W x 4ch (DIN 45324, +B=14.4V)
Continuous average power output:
17W x 4ch
(4 ohm, 20Hz to 20kHz, 1%THD)
Bass control action:
+14dB, -12dB(60Hz/80Hz/120Hz)
Treble control action: +/-12dB(8kHz/12kHz)
9 Band-G-EQ:
1 oct step GAIN +/-12dB
(63Hz to 16kHz)
Line output level:
1.8V(CD 1kHz)
General
Power supply voltage: 14.4V DC
(10.8V to 15.6V allowable)
Ground:
Negative
Current consumption: Less than 15A, 3A
Speaker impedance: 4 ohm(4 ohm to 8 ohm)
Dimensions(mm):
178(W) x 100(H) x 160(D)
Weight:
2.3kg
WXZ468RMP
COMPONENTS
PE-2758E-A
1.
2.
2-1.
2-2
3.
3-1.
3-2.
3-2-1.
3-2-2.
3-2-3.
3-2-4.
Main unit
Extension lead
FUSE(3A)
FUSE(15A)
Parts bag
Finisher
Parts bag
Machine screw(M5 x 8)
Hex-head screw(M5 x 8)
Spacer
Double face
----------854-6418-50
120-0030-00
120-0150-00
----------383-0591-00
----------714-5008-4B
716-0496-51
340-1581-00
347-3913-20
1
1
1
1
1
1
1
8
8
8
2
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in charge
of repair or inspection can avoid suffering any risk or
injury.
1. Use specified parts.
The system uses parts with special safety features against fire
and voltage. Use only parts with equivalent characteristics
when replacing them.
The use of unspecified parts shall be regarded as remodeling
for which we shall not be liable. The onus of product liability
(PL) shall not be our responsibility in cases where an accident
or failure is as a result of unspecified parts being used.
2. Place the parts and wiring back in their original positions after
replacement or re-wiring.
For proper circuit construction, use of insulation tubes, bonding, gaps to PWB, etc, is involved. The wiring connection and
routing to the PWB are specially planned using clamps to keep
away from heated and high voltage parts. Ensure that they are
placed back in their original positions after repair or inspection.
If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back securely
in their original position after repair. Ensure for safety reasons
there is no possibility of secondary ploblems around the repaired spots.
If extended damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts
for the automobile.
Disconnect the battery terminal after turning the ignition key
off. If wrong wiring connections are made with the battery connected, a short circuit and/or fire may occur. If extensive damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company.
5. Cautions in soldering
Please do not spread liquid flux in soldering.
Please do not wash the soldering point after soldering.
WXZ468RMP
6. Cautions in soldering for chip capacitors
Please solder the chip capacitors after pre-heating for replacement because they are very weak to heat.
Please do not heat the chip capacitors with a soldering iron
directly.
7. Cautions in handling for chip parts.
Do not reuse removed chips even when no abnormality is observed in their appearance. Always replace them with new
ones. (The chip parts include resistors, capacitors, diodes, transistors, etc).
Please make an operation test after replacement.
8. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron
tip temperature is around 270 . Take care not to apply the
iron tip repeatedly(more than three times)to the same patterns.
Also take care not to apply the tip with force.
9. Turn the unit OFF during disassembly and parts replacement.
Recheck all work before you apply power to the unit.
10. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through the
lens of the optical pickup. When checking that the laser optical diode lights up, keep your eyes more than 30cms away
from the lens. Prolonged viewing of the laser within 30cms
may damage your eyesight.
11. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by electrostatic charge caused by your clothes and body. Make sure
to avoid electrostatic charges on your clothes or body, or discharge static electricity before handling the optical pickup.
11-1. Laser diode
The laser diode terminals are shorted for transportation in order to prevent electrostatic damage. After replacement, open
the shorted circuit. When removing the pickup from the mechanism, short the terminals by soldering them to prevent this
damage.
11-2. Actuator
The actuator has a powerful magnetic circuit. If a magnetic
material is put close to it. Its characteristics will change. Ensure that no foreign substances enter through the ventilation
slots in the cover.
11-3. Cleaning the lens
Dust on the optical lens affects performance.
To clean the lens, apply a small amount of isopropyl alcohol to
lens paper and wipe the lens gently.
-2-
CAUTION
NOTES OF ISO CONNECTOR
This appilance contains a laser system and is classified as
a "CLASS 1 LASER PRODUCT" . In case of any trouble
with this player, please contact your nearest "authorized
service station" . To prevent direct exposure to the laser
beam, do not to open the enclosure.
1. For VW/Audi/Opel/Vauxhall vehicles, change the position of fuse installation as shown on the diagram.
(Figure 1)
Initial setting of Ex-lead
Yellow
Fuse
Yellow
Fuse
To Main unit
Red
Red
Blue/White
Blue/White
ISO
CONNECTOR
Remote
Top view
SYSTEM CHECK
For models up to 1991
For models 1992 and later
This function verifies the devices hooked up through CeNET.
1. Press the [ADJ] button to switch to the adjust mode.
2. Turn the [SEARCH] knob to select "SYS CHECK" .
3. Press and hold the [SEARCH] knob for 1 second or
longer to start the system check.
The digital connection configuration is automatically
checked.
When the system check is complete, the display returns
to the previous mode.
ANTI-THEFT INDICATOR
The red Anti-theft indicator is a function for detering theft.
The disc indicator for the [DIRECT] button "2" blinks.
* The factory default setting is "OFF".
1. Press the [ADJ] button to switch to the adjust mode.
2. Turn the [SEARCH] knob to select "BLINK LED".
3. Turn the [A-MODE] knob to select "ON" or "OFF".
4. Press the [ADJ] button to return to the previous mode.
Yellow
Yellow
Yellow
Red
Red
Red
Red
Figure 1
2. When the car stereo is installed in 1998 and later
Volkswagen models, remove the auto antenna leads (A5:Blue/White). Be sure to insulate both the ISO connector side terminal and the main unit side terminal with
insulation tape, respectively. (Figure 2)
3. When the main unit is also connected to an external am
plifier, connect REMOTE on the external amplifier to remote turn-on lead.
Insulation tape
Blue/White
Blue/White
Auto ant.(A-5)
Remote
turn-on
Insulate the terminal
* Never let the terminals make contact
with the metal plate parts of the car.
Figure 2
-3-
WXZ468RMP
CD/MP3
General
TROUBLE SHOOTING
Problem
Cause
Measure
Power does not
turn on.
(No sound is
produced.)
Fuse is blown.
Replace with a fuse of the same amperage(3A,15A).
Nothing happens
when buttons are
pressed.
The microprocessor has
malfunctioned due to noise,
etc.
Press the reset button for
about 2 seconds with a thin rod.
"Push EJECT" is
displayed.
Something is wrong with disc
or mechanism.
Press the [
] button to avoid the trouble.
If the situation is not improved despite you press the
[ ] button several times.
"FAIL**** " is
displayed.
Anti-theft function is out of order.
Press and hold the reset button for 2 seconds or longer.
No audio.
MP3/WMA files are absent
on the disc.
Write MP3/WMA files onto the disc properly.
Files are not recognized as
an MP3/WMA file.
Use MP3/WMA files encoded properly.
File system is not correct.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
MP3/WMA files are not
encoded properly.
Use MP3/WMA files encoded properly.
File system is not correct.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
Sound is cut or
skipped.
Noise is
generated or
noise is mixed
with sound.
Wrong filename
ERROR DISPLAYS
DVD changer
CD changer
CD/MP3
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Error Display
Cause
Measure
ERROR 3
A DISC cannot be played due to scratches, etc.
Replace with a non-scratched disc.
ERROR 4
A foreign object is pinched in the DISC slot,
or the shutter is damaged due to opening
the shutter forcibly, etc.
Remove the object inside the slot.
If there is no foreign object or the situation is not
improved in spite of removing it.
ERROR 6
A DISC is loaded upside-down inside the
CD deck and cannot play.
Eject the disc then reload it properly.
ERROR 2
A DISC inside the CD changer is not loaded
properly.
This is a failure of CD changer's mechanism.
ERROR 3
A DISC inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched disc.
ERROR 6
A DISC inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
ERROR 2
A DISC inside the DVD changer is not
loaded properly.
This is a failure of DVD mechanism.
ERROR 3
A DISC cannot be played due to scratches, etc.
Retry or replace with a non-scratched disc.
ERROR 6
A DISC inside the DVD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
ERROR P
Parental level error
Set the correct Parental level.
ERROR R
Region code error
Eject the disc and replace correct region code disc.
If an error display other than the ones described above appears, press the reset button.
If the problem persists, turn off the power.
WXZ468RMP
-4-
Clearing the error history and frequency
SELF-DIAGNOSIS FUNCTION
Model name/Inducing/Micom version
confirmation
1. Press the [ADJ] button to switch to the adjust mode.
2. Turn the [SEARCH] knob to select "SYS CHECK" .
* Micom version display :
Keep pressing the [1] button until the display changes.
Display : " MAIN *. ** "
* Mechanism micom version display :
Keep pressing the [2] button until the display changes.
Display : " MECH **. ** "
* Model name display and inducing display :
Keep pressing the [3] button until the display changes.
Display : " * PE275** "
* CCC-TUNER version display :
Keep pressing the [4] button until the display changes.
Four items of the following are switched with the
[SEARCH] knob.
(1) E2PROM Version display
: " E2pVer_*** "
(2) MapType display
: " MapType_** "
(3) Test Version
: " TestVer_** "
(4) Tuner Hardware Version
: " Hard___*** "
* Keep pushing the [5] button until VFD turn on all the
light.
* Keep pushing the [6] button until VFD turn off all the
light.
When the micom version is displayed, press the [FUNC]
key. Then the micom version display is canceled, enters
the state of POWER ON.
When ACC is set to ON from OFF, the micom version
display is canceled, too.
1. Press the [3] button for two seconds or more at the error
history confirmation mode.
2. Press and hold the [6] button pressing the [4] button while
displaying as EEP.
Display : " EEP CL3 "
" EEP CL2 "
" EEP CL1 "
" EEP CL
" EEP CL1 "
"
3. The error history and frequency are cleared.
4. When ACC is set to ON from OFF, the error history and
frequency are cleared again.
RDS error count confirmation
1. Press the [SCN] button and the [1] button at the same
time to the tuner mode.
Display : "
WAIT
Display : " * * %
"
*** "
The number of acquisition
of RDS block data
The rate of acquisition
of RDS block data
Error history confirmation
Take out the disc of the main unit before confirming the
error history.
1. Press the [ADJ] button to switch to the adjust mode.
2. Turn the [SEARCH] knob to select "SYS CHECK" .
3. Press the [SCN] button and the [RDM] button at the same
time for two seconds or more.
Display : " H01 * * * * "
The number of disk at error
"A" at the first error after back up on
The space at the other modes
It is possible to switch from "H01" to "H20" with the
[SEARCH] knob.
The number of mechanism errors exceeds 20 and a new
error occurs, the content of the latest error enters "H01".
* Press the [1] button for one second or more when returning it except the error history confirmation mode.
Error frequency confirmation
1. Press the [2] button for one second or more at the error
history confirmation mode.
Display : " T01 * * * * * "
The number of times at error
-5-
WXZ468RMP
ADJUSTMENT OF CCC-TUNER
: 880-2150A
Adjustment for S-meter
The data of receiving area and adjustment point are written
in the memory of a spare tuner pack. It is possible to receive a broadcast with no adjustment. However, please
adjust it to use the unit with the better conditions.
1. Connect the antenna input terminal of the unit to S.S.G.
2. Adjustment in order of Slope, Start and Point.
The reception frequency of the set is as follows.
* Reception frequency of FM : 98.1MHz
* Reception frequency of MW : 999kHz
* Reception frequency of LW : 216kHz
Click the " Alignment " button of [ FM S-Meter Slope ] of
the display. Then, a set level of SG is displayed.
Set the ATT value of SG to the level.
Input 26dBu at this unit. Click the " OK " button, and the
acquisition of the first data starts.
3. A set level of SG is displayed again after a while.
Change the ATT value of SG to the level.
Input 46dBu at this unit.
4. When the adjustment is completed, it is displayed with
" COMPLETED ". Then click the " OK " button.
The acquired value is displayed in the display.
5. Click the " Alignment " button of [ FM S-Meter Start ] of
the display. Set the ATT value of SG to the level. Input
26dBu at this unit.
6. When the adjustment is completed, it is displayed with
" COMPLETED ". Then click the " OK " button.
The acquired value is displayed in the display.
7. Click the " Alignment " button of [ FM S-Meter Point ] of
the display. Set the ATT value of SG to the level. Input
46dBu at this unit.
8. When the adjustment is completed, it is displayed with
" COMPLETED ". Then click the " OK " button.
The acquired value is displayed in the display.
9. The adjustment of FM was completed.
Change the reception band of the unit to MW, and adjust MW in the order from " Slope " as well as FM.
After adjusting MW, adjust LW as well as MW.
10.After all the adjustments, press the reset button of the
unit to set the data.
Measuring instrument
1. Personal computer with Windows98SE/WindowsME/
Windows2000 or WindowsXP operating system
2. Adjustment software : CCC-TUNER Alignment for
CeNET soft
3. CeNET analyzer
4. SG
5. AM ANT Dummy box
Writing the parameter
[ Strat up ]
1. Install the adjustment software in the personal computer.
2. Connect the unit to the personal computer with the
CeNET analyzer.
3. Open the adjustment software in the computer, and turn
on the unit.
Display
B. Initialization of JIG
A. Open Comm. PORT
C. Incoming connection
CCC Tuner Alignment for Ce-NET
MENU ALIGNMENT ROM RAM
Settings
Open Comm. PORT
AREA
TUNER
Incoming
connection
Initialization of JIG
ROM DATA MAP
RDS TUNER
BAND - Alignment
MW(AM)
FM
LW
FM S-Meter Slope
Alignment
LEVEL
FM S-Meter Start
Alignment
FM S-Meter Point
Alignment
FM IF-Count
Check
ROM
Address DATA
DATA Read
DATA Write
OK
DATA
Read ALL
Confirmation after all adjustments
DATA Write (0x70-0xFF)
Reconfirm the version of the parameter file after all adjustments are completed.
1. Press the [ADJ] button to switch to the adjust mode.
2. Turn the [SEARCH] knob to select "SYS CHECK" .
* Microcomputer version display : Keep pressing the [1]
button until the display changes.
Display : " MAIN *. ** "
* Model name and destination display : Keep pressing
the [3] button until the display changes.
Display : " * PE***** "
* CCC-TUNER version display : Keep pressing the [4]
button until the display changes.
Four items of the following are switched with the
[SEARCH] knob.
(1) E2PROM Version display
: " E2pVer_*** "
(3) Test Version
: " TestVer_** "
(2) MapType display
: " MapType_** "
(4) Tuner Hardware Version
: " Hard___*** "
DATA Write (0x00-0xFF)
CheckSUM
FM S-Meter Adjustment
4. Click the " A. Open Comm.PORT " button of the display.
The communication of the personal computer and the
analyzer starts.
5. Click the " B. Initialization of JIG " button of the display.
The personal computer sends the command for operation of the analyzer.
6. Click the " C. Incoming connection " button of the display. The unit recognizes the external jig. The preparation completes.
[ Setting of reception band ]
1. The indicator blinks according to the reception when the
connected processing ends normally.
2. The adjustment band is automatically set by the main
microcomputer of the unit and memorized in EEPROM
in CCC-TUNER.
3. Press the reset button of the unit to set the data.
WXZ468RMP
-6-
EXPLANATION OF IC
052-3404-10
uPD703272YGC-307-8EA-A
Terminal Description
pin 1: A Vref 0
System Controller
pin 56: KEY INT
: IN : Key interrupting signal input.
pin 57: NU
: IN : Not in use.
pin 58: NU
: IN : Not in use.
pin 59: 5V REM
: O : ON signal output to the 5V power supply.
pin 60: CD 9V REM
: O : 9V power supply ON signal output for CD.
H=ON.
: O : Mechanism ACC control signal output.
: - : Reference voltage for the internal ADC.
pin
2: A VSS
: - : Negative voltage supply for analog section.
pin 61: MECH ACC
pin
3: SYS ACC
: O : ACC detect signal output.
pin 62: CLK TEST
: O : Sub clock test port.
: O : The system muting command output.
pin 63: INIT 1
: IN : The initial setting input.
Refer Table 1.
pin 64: INIT 2
: IN : The initial setting input.
Refer Table 1.
pin 65: LED 1
: O : LED ON signal output. H=ON.
pin 66: LED 2
: O : LED ON signal output. H=ON.
pin 67: LED 3
: O : LED ON signal output. H=ON.
pin
4: LINE SYS MU
pin
5: A Vref 1
: - : Reference voltage for the internal DAC.
pin
6: NU
: IN : Not in use.
pin
7: AMP MUTE
: O : Muting signal output to the Audio Power
Amplifier.
pin
8: FLASH MODE
: IN : The flash memory mode setting input.
pin
9: VDD
: - : Positive voltage supply.
pin 10: REG C
: - : The capacitor connection.
pin 68: NU
: IN : Not in use.
pin 69: B VSS
: - : Ground for the bus interface section.
pin 70: B VDD
: - : Positive voltage supply for the bus interface section.
pin 71: KEY DI
: IN : The serial data input from the Key scan
IC.
pin 11: GND
: - : Ground.
pin 12: X 1
: - : The crystal connection.
pin 13: X 2
: - : The crystal connection.
pin 14: RESET
: IN : Reset signal input.
pin 15: XT 1
: - : Crystal connection.
pin 72: KEY DO
: O : The serial data output to the Key scan IC.
pin 16: XT 2
: - : Crystal connection.
pin 73: KEY CK
: O : Clock pulse output to Key-IC.
pin 17: ILL DET
: IN : Illumination ON signal input.
pin 74: KEY CE
: O : Chip enable output to Key-IC.
pin 18: CATS DET
: IN : The backup voltage detection for CATS.
pin 75: KEY RESET
: O : Reset pulse output to Key-IC.
pin 19: BU DET 1
: IN : Backup-voltage detection to mute the audio signal.
pin 76: NU
: IN : Not in use.
pin 77: VOL CW
pin 20: NU
: IN : Not in use.
: IN : The pulse signal input from the rotary
encoder.
pin 21: ACC DET
: IN : ACC detection signal input.
pin 78: VOL CCW
pin 22: DSP I2C SDA
:I/O: I2C serial data input/output.
: IN : The pulse signal input from the rotary
encoder.
pin 23: DSP I2C SCL
: O : I2C serial clock output.
pin 79: SOURCE CW
pin 24: NU
: IN : Not in use.
: IN : The pulse signal input from the rotary
encoder.
pin 25: FLASH TX
: O : The serial data output for the flash memory.
pin 26: FLASH RX
: IN : The serial data input for the flash memory.
pin 27: CATS DI
: IN : Serial data input for CATS.
pin 82: A-MOME CCW : IN : The pulse signal input from the rotary
encoder.
pin 28: CATS DO
: O : Serial data output for CATS.
pin 83: PHONE INT
: IN : The telephone interrupt signal input.
pin 29: CATS SCK
: O : Serial clcock output for CATS.
pin 84: SPAN A
pin 30: CATS CS
: O : Chip select output for CATS.
: O : Spectrum analyzer frequency band selection signal output.
pin 85: SPAN B
: O : Spectrum analyzer frequency band selection signal output.
pin 86: SPAN C
: O : Spectrum analyzer frequency band selection signal output.
pin 80: SOURCE CCW : IN : The pulse signal input from the rotary
encoder.
pin 81: A-MODE CW
: IN : The pulse signal input from the rotary
encoder.
pin 31: IE BUS TX
: O : IE Bus serial data output.
pin 32: IE BUS RX
: IN : IE Bus serial data input.
pin 33: E VSS
: - : Ground.
pin 34: E VDD
: - : Positive voltage supply.
pin 87: ILL REM
: O : Key illumination ON signal output. H=ON.
pin 35: MECH SDA
:I/O: The serial data input/output for GIX-MP3
mechanism.
pin 88: DD REM
: O : DC to DC Converter ON signal output.
H=ON.
pin 36: MECH SCL
: O : The serial clock output for GIX-MP3 mechanism.
pin 89: SPAN DATA
: IN : The serial data input from the spectrum
analyzer.
pin 37: MECH SRQ
: IN : The request input from GIX-MP3 mechanism.
pin 90: KEY AD
: IN : Input terminal of A/D converter for Key
judgment.
pin 38: MECH RESET
: O : The reset signal output for GIX-MP3
mechanism.
pin 91: NU
: IN : Not in use.
pin 92: NU
: IN : Not in use.
pin 39: RDS TP 3
pin 40: NU
: O : The test point for RDS PI.
: IN : Not in use.
pin 41: NU
: IN : Not in use.
pin 42: DSP RESET
: O : Reset signal output to the DSP IC.
pin 43: TUN SDA
pin 44: TUN SCL
:I/O: I2BUS serial data input/output for the tuner pack.
: O : I2BUS serial clock output for the tuner
pack.
pin 93: LEVEL IN L
: IN : Power level detection port.
pin 94: LEVEL IN R
: IN : Power level detection port.
pin 95: NU
: IN : Not in use.
pin 96: NU
: IN : Not in use.
pin 97: RDS TP 1
: O : The test point for RDS.
pin 98: RDS TP 2
: O : The test point for RDS.
pin 45: TUN RD CL
: IN : RDS serial clock input.
pin 99: EXT AMP REM : O : ON signal output to the external Amplifier.
pin 46: TUN RD DA
: IN : RDS serial data input.
pin100: A ANT REM
pin 47: REMOCON
: IN : Remote controller signal input terminal.
pin 48: VFD LAT
: O : The latch strove signal output to the VFD
driver.
pin 49: VFD BLANK
: O : Blank pulse output to the VFD driver.
: O : The automatic antenna control signal output.
Table 1. The initial setting input
Japan
Europe
Asia
pin 50: MECHA MUTE : IN : Mechanism audio mute signal input.
Destination
INIT 1 ( pin 63 )
H
L
H
Asia
L
pin 51: VFD DO
: O : The serial data output to the VFD driver.
INIT 2 ( pin 64 )
H
L
L
H
pin 52: VFD CLK
: O : The clock pulse output to the VFD driver.
pin 53: CTRL
: O : Power supply ON signal output.
pin 54: INT AMP REM : O : ON signal output to the internal Amplifier.
pin 55: NU
: IN : Not in use.
-7-
WXZ468RMP
WXZ468RMP
AUX-IN
ANT
SYS-ACC
BUS 14V
-8-
CD
CHANGER
MECHANISM
B/U
SRC
VOL
SEARCH
KEY
MATRIX
REMOCON
RECEIVER
(IR701)
RS-671
PRESET
x3
(Q797)
(Q798)
(Q799)
PRESET
x3
(Q794)
(Q795)
(Q796)
RESET
2.0V
DET
(IC604)
F1 F2
VHV
S-80820CNMC
(Q214) (Q215)
ACC
3.3V
DC - DC
CONVERTER
(IC202)
(D216)
(Q205)
(Q206)
(Q207)
(Q208)
D/D
SW
B/U 4V
ACC IN
DISC ILL
SYS MUTE
UPD703272YGC
Ce-NET
13PIN
Ce-NET
13PIN
(Q614) (Q615)
CATS
DET
BUS 14V
ILL DET
B/U 5.7V
ROTALY-ENCODER x3
AMODE
(IC701)
KEY SCAN IC
LC75700T
B/U 3.3V
SELF
RETURN
ACC 3.3V
SDA
SYS 5V
VHV
A/B/C
SYS 5V
RDDA
F1 F2
DATA
ACC 5V
SCL
(IC606)
CD74HC4050
MAIN
MICOM
VFD (FL701)
POWER LEVEL(L/R)
BUFF
ACC3.3V
ACC 5V
ILL
SW
ILL
DET
ILL
8V
SW
CD 9V
PHONE
INT
(Q603)
(Q604)
(Q609)
(Q605)
(Q601)
(Q602)
(Q610)
(Q613)
ACC 3.3V
(Q213) (Q216)
(Q203)
VCC
(IC605)
B/U 3.3V
(IC605)
4V STB
CTRL
SWITCH PWB
ILL DET
5V-REM
(D215)
(D214)
(D213)
(IC101)
ILL 8V
(IC607)
BD4827G
2.7V
DET
CATS IC
BR93L46F
CD 3.3V
ACC 3.3V
ACC 5V
B/U 3.3V
4.3V DET
BD4843G
SYS 5V
MEMO 3.3V
ILL-DET
(IC603)
(IC201)
HA13168
AUDIO 9V
RST
CD 3.3V
CTRL
B/U DET1
ACC 3.3V
SYS-ACC
GOLD-C
ACC-DET
CAR
WIRED
REMOCON
(Q606) (Q607)
AUDIO 9V
POWER IC
(Q453)
(Q454)
(Q455)
(Q456)
AMP CTRL
CD 9V
RDCL
IE-BUS
X601
3.14M
X301
11.2896M
DAC
PLL 8.5V
MAIN 8.5V
MUTE
AMP
(Q608)
ACC 5V
X602
32.768K
REAR
(IC302) PCM3010
DSP (IC301)
TAS3103
(DZE)
CODEC
FAD
FRONT
ACC 5V
DRIVER
HA12187FP
SPEANA IC
BA3834F
ADC
LOUD
BASS
/
TRE
ACC 5V
IE-BUS
(IC602)
DIFF AMP
HA17558ATEL
(IC401)
DSP-SCL
DSP-SDA
DSP-RST
AUDIO 9V
(IC552)
DIFF AMP
HA17558ATEL
MUTE
BAL
VOL
(D2)
AUDIO(L,R)
(IC551)
(IC553)
AUDIO 9V
RDS
DEMODULATOR
ACC DET
BUFF
13
PIN
IIC 5.0V
(ACC 3.3V)
DIFF AMP
HA17558ATEL
PLL 8.5V
AUDIO 9V
TEF6903H
SEL
MAIN 8.5V
AUDIO+
(L,R)
(BL1)
CCC-TUNER
880-2150A
Ce-NET
J601
FM STEREO
DECODER
SYS MUTE
(IC403)
DIFF AMP
HA17558ATEL
BUS TUNER
TB2906HQ
AMP
B/U(BUS)
ILLUMI
PHONE
ACC
REM
B/U
LINE-OUT
REAR
LINE-OUT
FRONT
SP-OUT
4CH
BLOCK DIAGRAM
ANT
KEY ILL
EJECT
RESET
POWER
LOAD
(IC601)
B/U 4V
EXPLODED VIEW/PARTS LIST
Escutcheon section
29
30
56
35
37
12
35
35
26
23
35
18
28
60
37
52
30
59
33
34
19
57
22
24 56
35
20
54
10
35
8 33
32
55
9
31
38 x19
40
39
41
7
34 33
16
27
36
15
4
43
6
3
2
39
DESCRIPTION
40
50
39
50 39
48
62
45
53
45
41 39
42
PART NO.
46
45
44
1
PART NO.
47
49
39
5
NO.
61
45
34
21
14
11
7
25
58
17
13
63
45
51
Q'TY
NO.
1
371-5820-00 FACE PANEL(A)
1
33
DESCRIPTION
Q'TY
2
371-5821-00 FACE PANEL(B)
1
34
380-5616-00 KNOB CAP
3
3
371-5822-00 FACE PANEL(C)
1
35
716-0872-52 PAD SCREW(M1.7 x 5)
21
4
371-5823-01 FACE PANEL(D)
1
36
347-7526-00 DOUBLE FACE
1
5
371-5824-00 FACE PANEL(E)
1
37
347-7243-00 DOUBLE FACE
2
6
373-1073-02 DIAL-CVR
1
38
013-6312-50 SWITCH
19
347-7528-00 DOUBLE FACE
4
7
380-5635-00 KNOB
3
39
001-7040-91 LED(WHITE)
7
8
335-7548-00 KNOB-CAP
1
40
001-7043-90 LED(GREEN)
2
9
335-7573-00 KNOB-RING
1
41
001-7062-90 LED(RED)
6
10
380-5636-00 KNOB (A)
1
42
379-4056-28 VFD
1
11
380-5637-00 KNOB (B)
1
43
347-7405-00 SPACER
2
12
370-6176-01 ESCUTCHEON
1
44
060-4017-90 IR-RECIEVER
1
13
335-7547-00 FILTER(VFD)
1
45
716-0778-51 WAVE SCREW(2 x 6)
17
14
335-7549-00 ILLUMI PLATE(L)
1
46
074-3010-72 OUTLET SOCKET(22P)
1
15
335-7550-00 ILLUMI PLATE(R)
1
47
074-3010-60 OUTLET SOCKET(10P)
1
16
382-7458-00 BUTTON(RESET)
1
48
-----------
1
17
382-7451-00 BUTTON(BAD/D-Z)
1
49
016-9901-00 VR W/SHAFT(SEARCH)
1
18
382-7452-01 BUTTON(TA/ADJ)
1
50
2
19
382-7453-00 BUTTON(1,2,3)
1
016-9900-94 VR W/SHAFT
(A-MODE,SOURCE)
20
382-7454-00 BUTTON(TIE/RDM)
1
51
016-9900-84 VR W/SHAFT(VOLUME)
1
21
382-7455-00 BUTTON(SCN/RPT)
1
52
347-7878-00 FILM
1
22
382-7459-00 BUTTON(4,5,6)
1
53
001-7095-90 LED(BLUE)
1
23
382-7456-00 BUTTON(CD/S-A)
1
54
335-7554-00 ILLUMI PLATE
1
24
382-7457-00 BUTTON(L/D)OU
1
55
345-8090-00 CUSHION RUBBER
1
25
335-7553-00 ILLUMI PLATE(B)
1
26
335-7557-00 ILLUMI PLATE(L)
1
27
335-7556-00 ILLUMI PLATE(R)
1
28
346-0180-00 LEATHER SHEET
1
29
371-5832-01 TRIM PLATE
1
30
335-7551-00 ILLUMI PLATE(CD)
2
31
335-7561-00 ILLIMI-PLATE(A)
3
32
335-7555-00 ILLUMI PLATE(B)
3
-9-
SWITCH PWB
56
347-7884-00 FILM(E)
2
57
347-7877-00 FILM(D)
1
58
347-7876-00 FILM(C)
1
59
347-7875-00 FILM(B)
1
60
347-7874-00 FILM(A)
1
61
347-7321-00 E-SHEET
1
62
345-5598-00 CUSHION
1
63
347-6548-00 DOUBLE FACE
1
WXZ468RMP
Main section
27
29
2
11
29
10
29
6
7
27
24
9
32
30
33
27
4
26
5
26
25
21
23
16
28
19
20
27
25
31
12
25
30
22
27
16
14
17
13
3
25
27
18
16
15
8
1
27
NO.
Q'TY
NO.
1
PART NO.
311-1896-10 LOWER CASE
DESCRIPTION
1
18
2
310-1799-10 UPPER CASE
1
PART NO.
DESCRIPTION
Q'TY
092-4000-51 ANT-RECEPT
1
19
074-1214-00 OUTLET SOCKET
1
074-1194-00 OUTLET SOCKET(Ce-NET)
1
3
309-0813-00 FRONT-BRKT
1
20
4
331-4036-00 MECH-BRKT(L)
1
21
331-4035-00 IC HOLDER
1
5
331-4037-00 MECH-BRKT(R)
1
22
074-1237-69 OUTLET SOCKET(19P)
1
6
313-1941-00 HEAT SINK
1
23
307-0714-00 REAR PLATE
1
7
929-0371-81 CD-CHANG-MODULE
1
24
855-5535-50 RCA PIN CORD
1
716-0878-50 IT SCREW(M2.6 x 5)
5
714-3008-85 MACHINE SCREW(M3 x 8)
3
8
816-4023-50 FLAT WIRE
1
25
9
345-3799-20 RUBBER PART
6
26
10
286-6687-00 SETPLATE
1
27
714-2606-8B MACHINE SCREW(M2.6 x 6)
11
11
341-1823-00 SHAFT-S
1
28
780-3006-51 SCREW(M3 x 6)
1
12
347-7229-00 SPACER FILM
1
29
714-2610-8B MACHINE SCREW(M2.6 x 10)
6
716-3552-00 SCREW(M2.3 x 2.5)
6
060-6028-00 DC-DC CONVERTER
1
13
076-0648-22 PLUG(22P)
1
30
14
076-0648-10 PLUG(10P)
1
31
15
-----------
MAIN PWB
1
32
335-0833-01 LEAD HOLDER
1
16
073-0762-90 TERMINAL
3
33
855-0569-52 MINI JACK CORD
1
17
880-2150A
1
WXZ468RMP
CCC-TUNER
- 10 -
ELECTRICAL PARTS LIST
Switch PWB(B1) section
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
C701
C702
C703
C704
C705
C706
C708
C709
C710
D705
D706
D707
D708
D709
D710
D711
D712
D713
D714
D715
D716
D717
D718
D719
D720
D721
D722
D751
D752
D753
D754
D755
D756
D757
D758
D759
D766
D767
16V 0.1uF
1000pF K
16V 10uF
0.01uF K
16V 0.1uF
1000pF K
16V 0.1uF
5600pF
5600pF
NSCW100-T
NSCW100-T
NSCW100-T
NSCW100-T
NSCW100-T
HUB1105W-12-RR
NSCW100-T
NSCW100-T
CL-170FG F-GREEN
CL-170FG F-GREEN
RBR1111C
RBR1111C
RBR1111C
RBR1111C
RBR1111C
RBR1111C
MA111
MA111
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU3.9B2
D768
D769
D770
D771
FL701
IC701
IR701
J701
J702
L701
Q794
Q795
Q796
Q797
Q798
Q799
R710
R711
R712
R713
R714
R715
R716
R717
R718
R719
R720
R721
R722
R723
R724
R725
R726
R727
R728
R729
R730
R736
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
HZU 5.6B2
VFD
LC75700T
IR RECEIVER
10P
22P
NLV25 22uH J
KRC106S
KRC106S
KRC106S
KRC106S
KRC106S
KRC106S
1/10W 1k ohm
1/10W 39k ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 270 ohm
1/10W 270 ohm
1/10W 270 ohm
1/10W 270 ohm
1/10W 820 ohm
1/10W 560 ohm
1/10W 820 ohm
1/10W 270 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 100 ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 33k ohm
R737
R738
R739
R740
R741
R742
R743
R744
R745
R746
R747
S701
S702
S703
S704
S705
S706
S707
S708
S709
S710
S711
S712
S713
S714
S715
S716
S717
S718
S719
VR701
VR702
VR703
VR704
PWB
1/10W 2.7k ohm
1/10W 12 ohm
1/10W 12 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 10k ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
SKRP-ABE-010
VR W/SHAFT
VR W/SHAFT
VR W/SHAFT
VR W/SHAFT
PWB(WITHOUT
COMPONENT)
168-1042-78
168-1022-55
042-0423-97
168-1032-55
168-1042-78
168-1022-55
168-1042-78
043-0318-90
043-0318-90
001-7040-91
001-7040-91
001-7040-91
001-7040-91
001-7040-91
001-7095-90
001-7040-91
001-7040-91
001-7043-90
001-7043-90
001-7062-90
001-7062-90
001-7062-90
001-7062-90
001-7062-90
001-7062-90
001-0516-90
001-0516-90
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-32
001-4301-21
001-4301-32
001-4301-32
001-4301-32
001-4301-32
379-4056-28
051-6642-08
060-4017-90
074-3010-60
074-3010-72
010-3406-66
125-2199-96
125-2199-96
125-2199-96
125-2199-96
125-2199-96
125-2199-96
119-1021-15
119-3931-15
119-2211-15
119-2211-15
119-2211-15
119-2211-15
119-2211-15
119-2211-15
119-2711-15
119-2711-15
119-2711-15
119-2711-15
119-8211-15
119-5611-15
119-8211-15
119-2711-15
119-3311-15
119-3311-15
119-1011-15
119-1021-15
119-1021-15
119-3331-15
119-2721-15
119-1201-15
119-1201-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-1031-15
119-3311-15
119-3311-15
119-3311-15
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
013-6312-50
016-9900-84
016-9900-94
016-9900-94
016-9901-00
039-2797-01
Main PWB(B2) section
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
ANT1
BL1
C1
C2
C3
C4
C5
C6
C7
C8
C9
C11
C12
C13
C15
C16
C25
C102
C103
C104
C105
C106
C107
C108
C109
C110
C116
C125
ANTENNA RECEPT
CCC-TUNER
150pF CH
16V 47uF
0.022uF K
16V 47uF
0.022uF K
16V 47uF
0.022uF K
16V 10uF
16V 10uF
16V 10uF
16V 10uF
22pF CH
100pF CH
0.047uF K
50V 2.2uF
0.47uF
0.47uF
0.47uF
0.47uF
16V 10uF
50V 2.2uF
0.1uF
50V 1uF
0.47uF
1000pF K
1000pF K
C126
C127
C128
C129
C130
C131
C132
C205
C206
C207
C210
C211
C214
C216
C217
C218
C219
C220
C221
C223
C224
C225
C226
C301
C302
C303
C304
C305
1000pF K
1000pF K
1000pF K
1000pF K
1000pF K
1000pF K
1000pF K
35V 100uF
63V100uF
63V 47uF
16V 0.1uF
16V 0.1uF
16V 3300uF
16V 0.1uF
16V 0.1uF
16V 100uF
16V 0.1uF
16V 100uF
16V 100uF
0.047uF K
0.022uF K
16V 47uF
16V 0.1uF
15pF CH
15pF CH
0.01uF K
0.01uF K
35V 4.7uF
C306
C307
C308
C309
C310
C311
C312
C313
C314
C315
C316
C318
C319
C322
C323
C324
C325
C326
C327
C328
C329
C330
C331
C332
C333
C340
C341
C401
0.01uF K
16V 1uF
16V 1uF
16V 10uF
16V 10uF
16V 10uF
16V 0.1uF
10V 100uF
16V 0.1uF
16V 10uF
16V 0.1uF
16V 10uF
16V 0.1uF
16V 0.1uF
16V 0.1uF
16V 0.1uF
1000pF K
100pF CH
1000pF K
100pF CH
1000pF K
100pF CH
10V 100uF
10V 100uF
16V 0.1uF
0.047uF K
0.047uF K
16V 0.1uF
092-4000-51
880-2150A
166-1511-50
187-4763-35
168-2232-55
187-4763-35
168-2232-55
187-4763-35
168-2232-55
187-1063-35
187-1063-35
187-1063-35
187-1063-35
166-2201-50
166-1011-50
168-4732-78
187-2253-65
178-4742-78
178-4742-78
178-4742-78
178-4742-78
187-1063-35
187-2253-65
172-1041-15
187-1053-65
178-4742-78
168-1022-55
168-1022-55
168-1022-55
168-1022-55
168-1022-55
168-1022-55
168-1022-55
168-1022-55
168-1022-55
042-1393-00
042-1655-00
042-9134-00
168-1042-78
168-1042-78
189-3383-32
168-1042-78
168-1042-78
187-1073-35
168-1042-78
187-1073-35
187-1073-35
168-4732-78
168-2232-55
187-4763-35
168-1042-78
166-1501-50
166-1501-50
168-1032-55
168-1032-55
187-4753-55
- 11 -
168-1032-55
043-0540-02
043-0540-02
187-1063-35
187-1063-35
187-1063-35
168-1042-78
042-1631-50
168-1042-78
187-1063-35
168-1042-78
187-1063-35
168-1042-78
168-1042-78
168-1042-78
168-1042-78
168-1022-55
166-1011-50
168-1022-55
166-1011-50
168-1022-55
166-1011-50
042-1631-50
042-1631-50
168-1042-78
168-4732-78
168-4732-78
168-1042-78
WXZ468RMP
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
C402
C404
C405
C406
C408
C409
C410
C411
C412
C413
C414
C415
C416
C417
C421
C447
C448
C449
C450
C453
C454
C455
C456
C501
C502
C503
C504
C505
C506
C507
C522
C541
C542
C551
C552
C553
C554
C555
C556
C557
C558
C559
C560
C561
C565
C566
C567
C568
C569
C570
C571
C572
C573
C574
C575
C576
C577
C578
C579
C601
C602
C603
C604
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
16V 0.1uF
16V 0.1uF
16V 0.1uF
0.01uF K
16V 0.1uF
16V 0.1uF
0.047uF K
0.047uF K
16V 10uF
16V 10uF
16V 10uF
16V 10uF
50V 2.2uF
50V 2.2uF
16V 0.1uF
8200pF K
8200pF K
8200pF K
8200pF K
16V 10uF
16V 10uF
16V 10uF
16V 10uF
100pF CH
100pF CH
16V 0.1uF
2200pF K
2200pF K
270pF
270pF
16V 0.1uF
16V 10uF
16V 10uF
16V 10uF
16V 10uF
16V 10uF
16V 10uF
50V 2.2uF
50V 2.2uF
50V 2.2uF
50V 2.2uF
8200pF K
0.047uF K
8200pF K
0.047uF K
0.047uF K
50V 2.2uF
50V 2.2uF
50V 2.2uF
50V 2.2uF
16V 10uF
16V 10uF
50V 2.2uF
50V 2.2uF
16V 0.1uF
16V 0.1uF
16V 0.1uF
16V 10uF
16V 10uF
0.01uF K
100pF CH
100pF CH
16V 10uF
25V 33uF
100pF CH
10V 4.7uF
18pF CH
22pF CH
0.01uF K
6.3V 100uF
100pF CH
390pF CH
16V 100uF
5.5V 0.33F
C616
C617
C618
C619
C621
C622
C623
C624
C625
C626
C627
C628
C631
C632
D2
D201
D202
D203
D205
D206
D208
D209
D210
D211
D213
D214
D215
D216
D217
D301
D501
D502
D503
D504
D505
D506
D507
D551
D552
D553
D554
D601
D602
D603
D604
D605
D606
D607
D608
D609
D610
D611
F201
FIL302
FIL303
IC101
IC201
IC202
187-2263-15
168-1042-78
042-1596-00
168-4732-78
187-1063-35
187-4763-35
168-1042-78
168-2232-55
168-1042-78
168-1042-78
168-1042-78
168-2232-55
166-1011-50
166-1011-50
001-0535-90
001-0424-31
001-0347-42
001-0592-61
001-0516-90
001-0516-90
001-0466-91
001-0516-90
001-0644-90
001-0516-90
001-0516-90
001-0644-90
001-0516-90
001-0516-90
001-0466-91
001-4301-21
001-0516-90
001-0516-90
001-4301-24
001-4301-41
001-0535-90
001-0535-90
001-0535-90
001-0516-90
001-0516-90
001-0516-90
001-0516-90
001-0516-90
001-4301-32
001-0504-31
001-0535-90
001-0529-26
001-0516-90
001-0516-90
001-0516-90
001-0347-38
001-0516-90
001-0347-48
060-8053-90
060-3115-51
060-3115-51
051-2057-00
051-3324-00
060-6028-00
IC203
IC301
IC302
IC401
IC402
IC403
IC551
IC552
IC553
IC554
IC601
051-3335-90
051-6722-90
051-6723-90
051-5818-90
051-3054-90
051-3054-90
051-3054-90
051-3054-90
051-3054-90
051-3054-90
052-3404-10
IC602
IC603
IC604
051-6600-58
051-5446-08
051-5410-18
6.3V 22uF
16V 0.1uF
5.5V 0.33F
0.047uF K
16V 10uF
16V 47uF
16V 0.1uF
0.022uF K
16V 0.1uF
16V 0.1uF
16V 0.1uF
0.022uF K
100pF CH
100pF CH
MA729
MA4180
MA4075H
1N5404
MA111
MA111
S5688G
MA111
MA113
MA111
MA111
MA113
MA111
MA111
S5688G
HZU3.9B2
MA111
MA111
HZU 4.3B3
HZU 7.5B2
MA729
MA729
MA729
MA111
MA111
MA111
MA111
MA111
HZU 5.6B2
HZS6 A2L
MA729
MA8047-M
MA111
MA111
MA111
MA4068M
MA111
MA4091H
CHIP FUSE 1.3A
CKD310JB1C224ST
CKD310JB1C224ST
TB2906HQ
HA13168
DC-DC CONVERTER
AN77L04M
TAS3103IDBTR
PCM3010DBR
BA3834F
HA17558ATEL
HA17558ATEL
HA17558ATEL
HA17558ATEL
HA17558ATEL
HA17558ATEL
uPD703272YGC307-8EA-A
HA12187FP
BD4843G-TR
S-80820CNMC-8BF
IC605
IC606
IC607
J101
J601
J901
L1
L3
L4
L5
L101
L201
L202
L203
L301
L302
L303
L304
L305
L401
L403
L404
L405
L406
L407
L408
L409
L410
L520
L521
L601
L602
L603
P601
P602
Q203
Q205
Q206
Q207
Q208
Q212
Q213
Q214
Q215
Q216
Q453
Q454
Q455
Q456
Q501
Q502
Q503
Q601
Q602
Q603
Q604
Q605
Q606
Q607
Q608
Q609
Q610
Q613
Q614
Q615
Q618
Q619
R1
R2
R4
R5
R6
R101
R102
BR93L46F-W
CD74HC4050PWR
BD4827G
16P
13P CE-NET
19PIN
30uH
6.8uH
6.8uH
6.8uH
130uH
220uH J
100uH
5.6uH J
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
NLV25 1uH J
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1.5k ohm/100MHz
1k ohm/100MHz
47uH J
5.6uH J
5.6uH J
47uH J
10P
22P
KTC2026
2SB1243
KTC3875S
KTC3875S
2SB1243
2SB1237
RN2427
RN2427
KRC102S
KRC102S
KTD1304
KTD1304
KTD1304
KTD1304
KRC106S
KRA106S
KTC3875S
KTA1504S
KTC3875S
KRA102S
KRC103S
KTA1504S
KTA1504S
KRC102S
KRC102S
KTC2026
KTA1298
KRC102S
KRA103S
2SC2712
KRA102S
KRC106S
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 100k ohm
1/10W 10k ohm
1/10W 27k ohm
168-1042-78
168-1042-78
168-1042-78
168-1032-55
168-1042-78
168-1042-78
168-4732-78
168-4732-78
187-1063-35
187-1063-35
187-1063-35
187-1063-35
187-2253-65
187-2253-65
168-1042-78
168-8222-55
168-8222-55
168-8222-55
168-8222-55
187-1063-35
187-1063-35
187-1063-35
187-1063-35
166-1011-50
166-1011-50
168-1042-78
168-2222-55
168-2222-55
166-2711-50
166-2711-50
168-1042-78
187-1063-35
187-1063-35
187-1063-35
187-1063-35
187-1063-35
187-1063-35
187-2253-65
187-2253-65
187-2253-65
187-2253-65
168-8222-55
168-4732-78
168-8222-55
168-4732-78
168-4732-78
187-2253-65
187-2253-65
187-2253-65
187-2253-65
187-1063-35
187-1063-35
187-2253-65
187-2253-65
168-1042-78
168-1042-78
168-1042-78
187-1063-35
187-1063-35
168-1032-55
166-1011-50
166-1011-50
187-1063-35
187-3363-45
166-1011-50
042-0423-94
166-1801-50
166-2201-50
168-1032-55
042-1577-00
166-1011-50
166-3911-50
187-1073-35
042-1596-00
WXZ468RMP
- 12 -
051-9400-29
051-7285-08
051-5418-18
074-1214-00
074-1194-00
074-1237-69
010-2003-04
010-6009-70
010-6009-70
010-6009-70
010-8038-01
010-6009-88
010-2272-03
010-6009-69
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3406-50
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3103-64
010-3105-62
010-6009-80
010-6009-69
010-6009-69
010-6009-80
076-0648-10
076-0648-22
125-4015-90
191-1243-00
125-4010-90
125-4010-90
191-1243-00
191-1237-00
125-0013-97
125-0013-97
125-2199-92
125-2199-92
125-4012-90
125-4012-90
125-4012-90
125-4012-90
125-2199-96
125-0199-96
125-4010-90
125-3004-90
125-4010-90
125-0199-92
125-2199-93
125-3004-90
125-3004-90
125-2199-92
125-2199-92
125-4015-90
125-3007-90
125-2199-92
125-0199-93
192-2712-00
125-0199-92
125-2199-96
119-4721-15
119-4721-15
119-4721-15
119-4721-15
119-1041-15
119-1031-15
119-2731-15
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
REF No. PART No.
DESCRIPTION
R112
R113
R114
R115
R201
R202
R203
R206
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R219
R220
R230
R231
R304
R305
R312
R313
R314
R315
R333
R334
R335
R336
R337
R340
R341
R342
R343
R401
R402
R403
R404
R410
R411
R412
R413
R414
R415
R416
R417
R418
R419
R420
R421
R427
R429
R431
R432
R447
R448
R449
R450
R453
R454
1/10W 1k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 68k ohm
1/10W 100k ohm
1/10W 10k ohm
1/10W 220 ohm
1/4W 560 ohm
1/10W 47k ohm
1/4W 2.7k ohm
1/4W 2.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/4W 10k ohm
1/10W 1k ohm
1/10W 22k ohm
1/10W 47k ohm
1/4W 18k ohm
1/4W 1.5k ohm
1/10W 18 ohm
1/10W 100k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 0 ohm JW
1/10W 1.5k ohm
1/10W 820 ohm
1/10W 820 ohm
1/10W 820 ohm
1/10W 220 ohm
1/10W 0 ohm JW
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 150k ohm
1/10W 15k ohm
1/10W 100k ohm
1/10W 150k ohm
1/10W 100k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 100k ohm
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 22k ohm F
1/10W 22k ohm F
1/10W 22k ohm F
1/10W 22k ohm F
1/10W 100 ohm
1/10W 100 ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 22k ohm
1/10W 22k ohm
R455
R456
R459
R460
R461
R462
R464
R465
R523
R536
R537
R538
R540
R551
R552
R553
R554
R555
R556
R557
R558
R559
R560
R561
R562
R564
R566
R567
R568
R569
R570
R571
R572
R573
R574
R575
R576
R577
R578
R579
R580
R581
R582
R583
R584
R585
R586
R601
R602
R603
R604
R606
R607
R608
R609
R610
R611
R612
R613
R614
R615
R622
R623
R624
1/10W 22k ohm
1/10W 22k ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 330 ohm
1/10W 1k ohm
1/10W 8.2k ohm
1/10W 3.3k ohm
1/10W 22k ohm
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 56k ohm F
1/10W 15k ohm F
1/10W 15k ohm F
1/10W 15k ohm F
1/10W 15k ohm F
1/10W 220 ohm
1/10W 24k ohm
1/10W 220 ohm
1/10W 24k ohm
1/10W 39k ohm
1/10W 39k ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 3.9k ohm
1/10W 3.9k ohm
1/10W 1k ohm
1/10W 1k ohm
1/10W 3.9k ohm
1/10W 3.9k ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 8.2k ohm
1/10W 8.2k ohm
1/10W 8.2k ohm
1/10W 8.2k ohm
1/10W 8.2k ohm
1/10W 8.2k ohm
1/10W 0 ohm JW
1/10W 0 ohm JW
1/4W 68 ohm
1/10W 3.3k ohm
1/10W 10k ohm
1/10W 1k ohm
1/10W 47k ohm
1/10W 47k ohm
1/10W 4.7k ohm
1/10W 10k ohm
1/4W 1.5k ohm
1/10W 47k ohm
1/10W 4.7k ohm
1/10W 10k ohm
1/4W 180 ohm
1/4W 180 ohm
1/10W 5.6k ohm
R625
R626
R627
R628
R629
R630
R631
R632
R633
R634
R635
R636
R637
R638
R639
R640
R641
R642
R643
R644
R645
R646
R647
R648
R649
R652
R653
R654
R655
R656
R660
R661
R662
R663
R664
R665
R666
R667
R668
R671
R672
R674
R675
R680
R681
R682
R683
R684
R685
R686
R687
R697
R698
SUP1
TM201
TM203
TM204
X301
X601
X602
PWB
1/10W 10k ohm
1/4W 180 ohm
1/10W 22k ohm
1/10W 10k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 100 ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 220k ohm
1/10W 47k ohm
1/10W 15k ohm
1/10W 10k ohm
1/10W 4.7k ohm
1/10W 4.7k ohm
1/10W 47k ohm
1/10W 1k ohm
1/10W 10k ohm
1/10W 100k ohm
1/10W 10k ohm
1/10W 10k ohm
1/10W 100k ohm
1/10W 0 ohm JW
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 0 ohm JW
1/10W 1.2k ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 330 ohm
1/10W 0 ohm JW
1/10W 0 ohm JW
DSP-141N-S00B
TERMINAL
TERMINAL
TERMINAL
11.2896MH
3.14MHz
32.768kHz
PWB(WITHOUT
COMPONENT)
119-1021-15
119-1021-15
119-1021-15
119-1021-15
119-6831-15
119-1041-15
119-1031-15
119-2211-15
116-5611-15
119-4731-15
116-2721-15
116-2721-15
119-4721-15
119-4721-15
119-4721-15
116-1031-15
119-1021-15
119-2231-15
119-4731-15
116-1831-15
116-1521-15
119-1801-15
119-1041-15
119-4721-15
119-4721-15
119-4721-15
119-4721-15
119-0000-05
119-1521-15
119-8211-15
119-8211-15
119-8211-15
119-2211-15
119-0000-05
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-1541-15
119-1531-15
119-1041-15
119-1541-15
119-1041-15
119-1021-15
119-1021-15
119-1041-15
032-0140-00
032-0140-00
032-0140-00
032-0140-00
032-0140-54
032-0140-54
032-0140-54
032-0140-54
119-1011-15
119-1011-15
119-1031-15
119-1031-15
119-2211-15
119-2211-15
119-2211-15
119-2211-15
119-2231-15
119-2231-15
119-2231-15
119-2231-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-1021-15
119-1021-15
119-3311-15
119-1021-15
119-8221-15
119-3321-15
119-2231-15
032-0140-00
032-0140-00
032-0140-00
032-0140-00
032-0140-51
032-0140-51
032-0140-51
032-0140-51
119-2211-15
119-2431-15
119-2211-15
119-2431-15
119-3931-15
119-3931-15
119-1041-15
119-1041-15
119-1021-15
119-1021-15
119-1021-15
119-1021-15
119-3921-15
119-3921-15
119-1021-15
119-1021-15
119-3921-15
119-3921-15
119-1041-15
119-1041-15
119-8221-15
119-8221-15
119-8221-15
119-8221-15
119-8221-15
119-8221-15
119-0000-05
119-0000-05
116-6801-15
119-3321-15
119-1031-15
119-1021-15
119-4731-15
119-4731-15
119-4721-15
119-1031-15
116-1521-15
119-4731-15
119-4721-15
119-1031-15
116-1811-15
116-1811-15
119-5621-15
119-1031-15
116-1811-15
119-2231-15
119-1031-15
119-4721-15
119-4721-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1011-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-1031-15
119-2241-15
119-4731-15
119-1531-15
119-1031-15
119-4721-15
119-4721-15
119-4731-15
119-1021-15
119-1031-15
119-1041-15
119-1031-15
119-1031-15
119-1041-15
119-0000-05
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-1041-15
119-1041-15
119-0000-05
119-1221-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-3311-15
119-0000-05
119-0000-05
060-0122-91
073-0762-90
073-0762-90
073-0762-90
061-3536-90
060-1541-90
061-1056-00
039-2796-01
CONNECTOR LAYOUT
AUX-IN / LEFT
WHITE
AUX-IN / RIGHT
RED
REAR / LEFT
RED
WHITE
REAR / RIGHT
RED
FRONT / LEFT
WHITE
FRONT / RIGHT
RED
BLACK
RCA PIN CORD
855-5535-50
LINE-OUT
GRAY
MINI JACK CORD
855-0569-52
CAR
WIRED
REMOCON
CL
0 7 2 8
M5 x 6 mm MA X
J601
RADIO ANT
J601 (CeNET)
12
11
7
8
3
4
1
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
9 10
5
6
13 2
Description
GND
BACK UP
L-CH(+)
N.C.
N.C.
BUS(+)
R-CH(+)
R-CH(-)
SYS-ACC
BUS(-)
L-CH(-)
ILLUMI
N.C.
Pin No.
(J101 ISO)
1 - B7
2 - B8
3 - B6
4
5 - B5
6 - A7
7 - B3
8
9 - B4
10 - A5
11 - B1
12 - A6
13 - B2
14
Color
Description
GRN
GRN/BLK
WHT/BLK
BRN
WHT
RED
GRY
GRY/BLK
BLU/WHT
PUR
ORG/WHT
PUR/BLK
YEL
SP R/L(+)
SP R/L(-)
SP F/L(-)
PHONE INT
SP F/L(+)
ACC
SP F/R(+)
N.C
SP F/R(-)
REMOTE
SP R/R(+)
ILLUMI
SP R/R(-)
BACK UP(BUS)
(3A FUSE)
BACK UP
(15A FUSE)
GND
N.C
N.C
N.C
J101
1 3 5 7 9 11 13
15 - A4 YEL
16 - A8 BLK
A1
A2
A3
-
2 4 6 8 10 12 14 16
EXTENSION LEAD
854-6418-50
GRY / BLK
WHT / BLK
GRAY
WHITE
PUR / BLK
GRN / BLK
PURPLE
GREEN
REMOTE
BLU / WHT
ISO CONNECTOR
B7 B8
A7 A8
B5 B6
A5 A6
B3 B4
A3 A4
B1 B2
A1 A2
BLACK
ACC
PHONE
MUTE
RED
BROWN
ORG / WHT
3A
BACK UP
FUSE(3A)
120-0030-00
YELLOW
15A
FUSE(15A)
120-0150-00
- 13 -
WXZ468RMP
15
YELLOW
CIRCUIT DIAGRAM
Switch PWB(B1) section
68 69
J701
074-3010-60
0V
R740 330
4 VFD_DO
R742 330
5 VFD_BLK
8.0V
R739
12
C710
5600p
C
C
C705 0.1
C709
5600p
8.0V
47.6V
0V
6 VFD_LAT
7 FILA1
8 FILA2
9 VHV
10 D/D-GND
- 14 -
Q799
KRC106S
8 VOL_CW
RST
9 KEY_RST
CE
10 KEY_CE
CL
11 KEY_CL
DI
12 KEY_DI
DO
P_3
13 KEY_DO
14 B/U 4V
15 LED_3
16 LED_2
17 LED_1
5.2V
R746 330
CL
3.2V
R747 330
DI
20 SYS +5V
21 ACC 3.3V
C704
0.01
R730
1K
C
RESET
D722 MA111
S719
D721
MA111
C706 1000p
R729
1K
C
R728
100
R737
2.7K
R736
33K
EJECT
O
S718
G1 G2
POWER
OUT
V
19 KEY-INT
22 KEY-ILL
LOAD
GND
GND
IR701
RS-671
CE
To page 18
P602 of Main PWB
R714 D717
220
Q798
KRC106S
7 VOL_CCW
VOL_CW
18 REMOCON
VCC
15 14
D720 R717
220
R713 D716
220
Q797
KRC106S
D719 R716
220
D718 R715
220
11
13 12
9
8
WXZ468RMP
Q796
KRC106S
Q795
KRC106S
Q794
KRC106S
R712
220 D715
D705
R718
270
R719
270
D706
D707
R720
270
D708
R721
270
D709
R722
820
R723
560
D710
D711
R724
820
D712
10
KI5
IC701
LC75700T
6 SRC_CW
4.0V
VR702(2/2)
SEARCH
G.EQ
DI
5 SRC_CCW
SRC_CW
P_1
S717
ENT
UP
VR703(2/2)
KI1
4 A-M_CW
SRC_CCW
RST
C703
10
16V
TAN
>>
KI4
CL
VOL_CCW
N.C
2 RESET
3 A-M_CCW
A-M_CW
R745 330
R711
39K
VR704(2/2)
SCN
KI1
KI2
C
RPT
KI2
A-M_CCW
DO
C702 1000p
S716
CE
R744 10K
C708 0.1
S712
KI3
1
3.3V
L701 22uH
3.2V
C
S708
KI3
J702
074-3010-72
P_2
R710 1K
S704
KI3
17 16
ADJ
DO
18
TA
KI4
20 19
BAND
KI4
KI5 RST
D766
HZU5.6B2
SPE/ANA
KI5
KS1 VDD
C
S715
7
S711
6
S707
KS1
5
S703
KI2
4
D-Z
3
6
KS2 OSC
2
5
KS2
1
4
KS3
P3/ P2/
KS5 KS6
P4/ P1
KS4
KS3 VSS
C701
0.1
S714
D755 HZU5.6B2
S710
D756 HZU5.6B2
S706
KS4
D757 HZU5.6B2
S702
KI1
D758 HZU5.6B2
TITLE
D759 HZU5.6B2
3
VR704(1/2)
<<
DN
D713
S713
2
RDM
R725
270
R727
330
D754
HZU5.6B2
KS4
S709
1
DISP
R726
330
D714
A-M_CCW
A-M_CW
P_1
VR703(1/2)
A-MODE
SRC_CCW
SRC_CW
S705
D753
KS3 HZU5.6B2
S701
D752
KS2 HZU5.6B2
D751
KS1 HZU5.6B2
VR701
VOLUME
VR702(1/2)
SOURCE
VOL_CW
VOL_CCW
P_2
P_3
C
D768 HZU5.6B2
D770 HZU5.6B2
D769 HZU5.6B2
R743 330
D771 HZU5.6B2
2 GND
3 VFD_CLK
R741 330
R738
12
1 F-GND
To page 18
P601 of Main PWB
0V
D767
HZU3.9B2
57 58 59 60 61 62 63 64 65
F2
F2
P-GND
VH1
L-GND
VDD
LAT
BK
CLK
VH2
9 10 11 12 13
SI
NC
8
NC
7
NC
6
NC
5
NC
NC
NC
2
NC
F1
1
NC
F1
FL701
PRINTED WIRING BOARD
Switch PWB(B1) section
COMPONENT SIDE
SOLDER SIDE
Caution:
COMPONENT SIDE: Parts on the
component side seen from the
component side are indicated.
To page 16
P602 of Main PWB
To page 16
P601 of Main PWB
SOLDER SIDE: Parts on the solder
side seen from the solder side are
indicated.
- 15 -
WXZ468RMP
Main PWB(B2) section
: Component side
No.
1
3
5
7
9
11
13
15
Description
SP R/L(+)
SP F/L(-)
SP F/L(+)
SP F/R(+)
SP F/R(-)
SP R/R(+)
SP R/R(-)
BACK UP
No.
2
4
6
8
10
12
14
16
Description
SP R/L(-)
PHONE INT
ACC
N.C
REMOTE
ILLUMI
BACK UP(BUS)
GND
J601
Ce-NET
J101
16
15
14 12 10 8 6 4 2
13 11 9 7 5 3 1
1
2 13
* Refer to page 13
for the extension lead
(854-6418-50).
5
4
10 9
8
6
12
3
7
11
No.
1
2
3
4
5
6
7
Description No. Description
8 R-CH(-)
GND
9 SYS-ACC
BACK UP
10 BUS(-)
L-CH(+)
11 L-CH(-)
N.C.
12 ILLUMI
N.C.
13 N.C.
BUS(+)
R-CH(+)
RCA PIN CORD
855-5535-50
RED
REAR
LEFT
WHITE
REAR
RIGHT
RED
FRONT
LEFT
WHITE
FRONT
RIGHT
RED
CAR
WIRED
REMOCON
BLACK
GRAY
10
1
VINYL-COAT-WIRE
800-0206-00
AUX-IN
RIGHT
RED
(red)
WHITE
(white)
LINE OUT
AUX-IN
LEFT
MINI JACK CORD
855-0569-52
DC-DC
converter
COMPONENT SIDE
Caution:
COMPONENT SIDE: Parts on the component side seen
from the component side are indicated.
Flat wire
816-4023-50
To page M16
J1 of CD changer mechanism
- 16 -
To page 15
J701 of Switch PWB
WXZ468RMP
To page 15
J702 of Switch PWB
Main PWB(B2) section
: Solder side
11
12
7
8
3
4
1
1 3 5 7 9 11 13
9 10
5
15
2 4 6 8 10 12 14 16
6
13 2
(white)
Description No. Description
8 R-CH(-)
GND
9 SYS-ACC
BACK UP
10 BUS(-)
L-CH(+)
11 L-CH(-)
N.C.
12 ILLUMI
N.C.
13 N.C.
BUS(+)
R-CH(+)
(red)
No.
1
2
3
4
5
6
7
1
10
1
No.
1
3
5
7
9
11
13
15
Description
SP R/L(+)
SP F/L(-)
SP F/L(+)
SP F/R(+)
SP F/R(-)
SP R/R(+)
SP R/R(-)
BACK UP
No.
2
4
6
8
10
12
14
16
Description
SP R/L(-)
PHONE INT
ACC
N.C
REMOTE
ILLUMI
BACK UP(BUS)
GND
3
SOLDER SIDE
Caution:
SOLDER SIDE: Parts on the solder side seen
from the solder side are indicated.
The parts of a dotted line express the parts on a component side.
- 17 -
WXZ468RMP
CIRCUIT DIAGRAM
8 FILA2
9 VHV
10 D/D-GND
5.0V
5.0V
C
R604 3.3K
0V
0V
C
C625
0.1
C626
0.1
8
7
6
C607
4.7
10V
TAN
2
C617 0.1
R646 47K
C
Q615
2SC2712
Q614
KRA103S
3 BUS 14V
2 BUS AUDIO R+
2 BUS AUDIO R2 BUS AUDIO L-
C631 100p
ILL ON:13.9V
ILL OFF:0V
D609
MA4068M
Q619
KRC106S
C
2 ACC 3.3V
2 AUDIO 9V
SP_A
IC603
BD4843G
C611
100 6.3V LN
2 SPAN-DATA
Q601 KTA1504S
R606
10K
ILL ON:0V
ILL OFF:13.8V
ILL ON:14.0V
ILL OFF:0V
R607
1K
ILL ON:13.4V
ILL OFF:0V
R609
47K
D604
MA729
3 ILL
D606
D605
MA8047M MA111
R613 47K
PHONE
R614
4.7K
3 PHONE
R615
10K
D601
MA111
DD_REM
3 DD_REM
R665 330
K_CE
R666 330
K_CL
R667 330
K_DI
R668 330
K_DO
4.0V
1
2
3 B/U 14V
13 14
GND
RST IN
RST OUT
11 12
15
0V
ILL 8V
10
4.7V
9
8.0V
B/U DET
8
AUDIO
9V
CTRL
7
8.9V
6
VCC
5
3.2V
4
13.9V
3
ACC 5V
2
5.2V
ANT
1
5.8V
3
R230
18
R206
220
3 B/U 5.7V
AMP_REM
3 ACC
R201
68K
CTRL
Q613
KRC102S
L601 5.6uH
Q203
KTC2026
13.2V
5.0V
D216
MA111
3 AMP-STBY
IC201 HA13168
4.4V
Q214
RN2427
3.2V
3.2V
R611
10K
IC203
AN77L04M
R612
1.5K
1/4W
K_INT
Q610
KTA1298
3 AMP-MUTE
D214 MA113
3.3V
Q213
RN2427
7.3V
R662
100K
8.0V
5.0V
8.0V
3 SYS-MUTE
ACC DET
AMP
CTRL
D215 MA111
3.3V
3 AUDIO 9V
R649 4.7K
3 FILA1
3 FILA2
3 VHV
To page 20
Main PWB 3/3
3 D/D-GND
- 18 -
WXZ468RMP
D208 S5688G
C226 0.1
C221
100 16V
C220
100 16V
C218
100 16V
C219 0.1
R202 100K
C217 0.1
3 GND
2 AUDIO 9V
2 GND
C
C
C
C
C
C223
0.047
C
C224
0.022
C225
47 16V
Q215
KRC102S
R231
100K
C216 0.1
R648
10K
Q606
KTA1504S
3.3V
F-GND
REMOCON
Q216
KRC102S
3 F-GND
REMOCON
3 REM
Q607
KRC102S
2 F-GND
CAR
WIRED
REMOCON
R655
10K
V_LAT
C619 0.047
V_BLK
To page 19
Main PWB 2/3
D608
MA111
To page 19
Main PWB 2/3
To page 20
Main PWB 3/3
R610
4.7K
C605
33
25V
5.6V
C604
10
16V
C615
0.33F
5.5V
RESET
D213
MA111
SP_DATA
3
C
C610
0.01
2
2 SPAN-C
Q605
KTA1504S
4
3
2
100
A-ANT
REM
1
R624
5.6K
5.6V
3.3V
SYS_MUTE
1
5.8V
3
C632
100p
2
0V
1
R672
100K
3.3V
2 SPAN-B
SP_C
R608 47K
S-80820CNMC
2 SPAN-A
SP_B
0V
IC604
4
Q602
5
KTC3875S
4
C
5
AVSS
AVREF0
99
13
To page 20
Main PWB 3/3
0V
R660
10K
R625
10K
3.3V
6
5
R671 100K
C628
0.022
SYS_ACC
AMP_REM
C618
0.33F
5.5V
6
Q618 KRA102S
C
X601 3.14MHz
3.3V
7
NC
AVREF1
R645
220K
C616
22
6.3V
C608 18p
LV_R
LV_L
R627
22K
SP_DATA
K_INT
3.3V
DD_REM
SP_C
SP_B
SP_A
PHONE
5
1
2
3
C
C601
0.01
25
23 24
21 22
19 20
17 18
C
AMP_MUTE
AMP_MUTE
EX-AMP_REM
C609 22p
X602 32.768KHz
13 14
11 12
10
9
FLASH_MODE
8
GND
REGC
VDD
98 RDS TP2
97 RDS TP1
NC
96
15 16
F_ RX 26
CATS DI 27
CATS_DO 28
CATS_CS 30
CATS_SCK 29
IEBUS_RX 32
EVSS 33
IEBUS_TX 31
NC
95
94 LEVEL_IN_R
90 KEY-A/D
89 SPAN-DATA
88 DD_REM
4
R675
1.2K
DI
DO
CS
SK
3.3V
M_SDA
MECH-SCL 36
M_SCL
M_RST
M_SRQ
MECH-SRQ 37
MECH-RESET 38
NC 40
NC 41
RDS TP3 39
87 ILL_REM
X2
X1
ACC ON(POW ON):3.3V
ACC OFF:0V
86 SPAN-C
85 SPAN-B
83 PHONE-INT
84 SPAN-A
82 AM_CCW
A_CCW
10
5
Description
GND
BACK UP
L-CH(+)
N.C.
N.C.
BUS(+)
R-CH(+)
R-CH(-)
SYS-ACC
BUS(-)
L-CH(-)
ILLUMI
N.C.
2 BUS AUDIO L+
AMP_MUTE
R639 10K
R640 10K
R641 10K
R643 10K
R642 10K
R644 10K
9
4
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
2 ACC 5V
C
R663 0
RESET
LINE/SYS_MUTE
L602 5.6uH
V_DO
0V
8
3
3.3V
Q212 2SB1237
V_CLK
47.6V
7
R603
68
1/4W
3.3V
AMP_STBY
0V
8.0V
8.0V
R628
10K
T_SDA
DSP_RST
TUN-SDA 43
DSP_RESET 42
TUN-SCL 44
TUN-RDCL 45
REMO
REMOCON 47
TUN-RDDA 46
49
VFD_LAT 48
52
53
54
55
56
57
58
59
60
61
62
XT2
MUTE ON:0V
MUTE OFF:3.3V
12
SYS_MUTE
0V
5 VFD_BLK
6 VFD_LAT
DSP_SDA
K_RST
5.2V
11
R647
D603
15K HZS6A2L
R664 330
R638 100
4 VFD_DO
J601
074-1194-00
V_CW
REMO
3 VFD_CLK
4
V_CCW
D610 MA111 L_1
3.2V
3
R636 10K
L_2
22 KEY-ILL
2 GND
ILL_DET
XT1
L_3
18 REMOCON
1 F-GND
DSP_SCL
4.0V
17 LED_1
P601
076-0648-10
B/U_DET1
CATS_DET
RESET ON:0.3V
RESET OFF:3.3V
R674
0
2
R637 10K
15 LED_3
16 LED_2
To page 14
J701 of Switch PWB
S_CW
1
5.2V
12 KEY_DI
S_CCW
R635 10K
5
ACC IN
B/U
5.7V
11 KEY_CL
R634 10K
6
3.9V
10 KEY_CE
A_CW
7
IC602
HA12187FP
5.8V
9 KEY_RST
A_CCW
R633 10K
8
AMP
8 VOL_CW
21 ACC 3.3V
KEY
RESET
DI
L203
5.6uH
7 VOL_CCW
R632 10K
C
To page 14
J702 of Switch PWB
6 SRC_CW
20 SYS +5V
KEY_CE
NC
ILL ON:0V
ILL OFF:3.6V
F_RX
C
5 SRC_CCW
19 KEY-INT
KEY_CL
NC
ACC_DET
B/U ON:5.6V
B/U OFF:0V
PHONE ON:3.2V
PHONE OFF:0V
81 AM_CW
2
C623
0.1
C
C624
0.022
4 A-M_CW
14 B/U 4V
KEY_DO
RESET ON:0.3V
RESET OFF:3.3V
RESET
3.3V
3 A-M_CCW
13 KEY_DO
0V
BVDD
KEY_DI
A_CW
2 RESET
R656
100K
K_CE
K_RST
BVSS
S_CW
1 N.C
D602
HZU5.6B2
P602
076-0648-22
1
1 NC
K_CL
NC
79 SRC_CW
K_DI
3.3V
D607 MA111
LED3
80 SRC_CCW
K_DO
LED2
DI
DO
1
F_TX
DSP_SDA
ACC ON(POW ON):5.2V
ACC OFF:0V
IC601
UPD703272YGC-307
S_CCW
0V
2 NC
50
51
M_LCH
63
3.3V
S-GND
64
0V
LED1
DO
CLK
0V
ACC ON:3.3V/OFF:0V
ACC ON(POW ON):3.3V
ACC OFF:0V
78 VOL_CCW
3 GND
M_RCH
INIT2
V_CCW
4 L CH
Q604
KRC103S
0V
INIT1
76
5 S-GND
L_3
CLK-TEST
65
6 R CH
0V
L_1
L_2
MECH_ACC
66
To page M15
7 GND
3.3V
CD_9V_REM
NC
8 GND
R698
0
M_RST
R654 1K
5
9 VDD
4
10 RESET
7 FILA1
R697
0
13.9V
IC607
BD4827G
11 B/U
3
12 SPDIF
3.3V
R623
180 1/4W
5V_REM
CE
0V
ACC ON(POW ON):3.3V
ACC OFF:0V
67
M_SDA
13 SDA
NC
NC
68
14 AMP-MUTE
R622
180 1/4W
KEY-INT
NC
VCC GND
Q608
KRC102S
DSP_SCL
NO KEY: 3.2V
EJECT:0V
POWER:0.4V
LOAD:2.0V
69
M_SCL
15 SCL
R626
Q603
KRA102S 180 1/4W
NC
70
16 SYS-ACC
C614 100 16V
M_SRQ
17 REQ
K_INT
71
9.6V
4.8V
CTRL
INT-AMP_REM
72
18 CD 9V
C621 10 16V
9.6V
AMP_STBY
Q609 KTC2026
D611 MA4091H
19 CD 9V
4.7V
C622
47
16V
J1 of CD changer mechanism
J901
074-1237-69
CTRL
VFD
CLK
73
R653
47K
VFD
_DO
74
M_LCH
CDM_LCH 2
75
CDM_S-GND 2
R682
330
VFD_BLK
R652
4.7K
S-GND
MECH_A_MUTE
M_RCH
CDM_RCH 2
V_CW
R687
330
77 VOL_CW
V_LAT
V_CLK
T_SDA
93 LEVEL_IN_L
5.0V
R681
330
SK
R629 4.7K
8
EVDD 34
7
MECH-SDA 35
6
NC
5
92
GND
4
91 TUN-LEVEL
T_SCL
3
V_BLK
R686
330
2
V_DO
2
1
NC
3.2V
CS
R631 10K
DSP_RST
0V
DSP_SDA
R661
10K
R630 4.7K
9
R680
330
10
IC606
CD74HC4050
12 11
VCC
DSP_SCL 2
TUN_SDA 2
14 13
DSP_SCL
DSP_SDA 2
TUN_SCL 2
16 15
LV_R
LEVEL_IN_R 2
DSP_RESET
IC605 BR93L46F-W
LV_L
LEVEL_IN_L 2
T_RDCL
L603 47uH
T_SCL
T_RDCL
R683 330
2
T_RDDA
T_RDDA
R685
330
C627 0.1
TUN_RDCL
R684
330
2
C
TUN_RDDA
R601 0
To page 19
Main PWB 2/3
R602 0
Main PWB(B2) section 1/3
To page 19
Main PWB 2/3
R562
24K
VOUTL
C579 R584
10 16V 8.2K
- 19 C507
270p
C505
2200p
C
5
1
R576
C570
2.2 50V 1K
WXZ468RMP
2
3
C569
R575
2.2 50V 1K
C572
10 16V
4
D554
MA111
R578
3.9K
L401
1uH
1
2
3
IC401
BA3834F
4
5
13 12
6
11 10
7
8
9
5.0V
C409 0.1
R427 100
C401 0.1
CDM_L
C
4
C
3
R556
15K(F)
2
C
1
R559 C557
220 2.2 50V
C
5
R404 150K
FIL303
C561 C559
8200p 8200p
+
GND
6
SP_A
OUT
+
7
SP_B
0V
OUT VCC
-
IC551
HA17558ATEL
C316
0.1
C560
0.047
C
D301
HZU3.9B2
R555
15K(F)
R557 15K(F)
C
C
C
C12 10 16V
C7 0.022
C6 47 16V
C5 0.022
C4 47 16V
C25 2.2 50V
C15 100p
C575
0.1
R401 150K
15 14
B
17 16
A
18
SP_C
8.9V
R558
15K(F)
C556
2.2
50V
5.0V
CDM_R
0V SP_DATA
0V
R431 10K
D552
MA111
R432 10K
BUS_L
C
R574
3.9K
R579 100K
C308 1
DATA
R572
C568
2.2 50V 1K
C571
10 16V
C577 0.1
R573
3.9K
C
C567
R571
2.2 50V 1K
C573
2.2 50V
C332
C331
100 10V 100 10V
RST ON:0V
RST OFF:3.3V
FIL302
8
C
6
+
R340
330
BUS_R
C555
2.2 50V
C402
0.1
7
-
DSP_SCL
R341
330
D551
MA111
8
GND
C
+
19
20
IC301
TAS3103IDBTR
3.2V
R312 4.7K
C
R314 0
C306
0.01
C
C
C
C408 0.1
0V
PLL 0
GP IO 0 GP IO 3
SD IN 4
CS 0
PLL 1
17 18
OUT
SD IN 2
SD IN 3
R313 4.7K
CS 1
GP IO 1 GP IO 2
15 16
OUT VCC
13 14
22 21
-
C
24 23
IC553
HA17558ATEL
C504
2200p
C565
0.047
SD IN 1
26 25
C566
0.047
11 12
R342
330
C305
4.7 35V
R315 1.5K
3.2V
28 27
BUS_R
CDM_L
CDM_R
AUX_L
AUX_R
BUS_L
8.6V
R402
15K
C
10
R305
4.7K
9
C328
100p
R343
330
SD OUT 1
M CLK I
D VDD
TEST _BYP_C
MICROCLK
_DIV
D VSS
I2C_SDA
I2C M_S
I2C_SCL
RST
8
C
C
C327 R304
1000p 4.7K
N.C
VDD S
C329
1000p
C313
100
10V
INPL
L4 6.8uH
C
4
L5 6.8uH
R403
100K
3
7
30 29
R5 4.7K
R4 4.7K
R2 4.7K
R1 4.7K
8.6V
T_RDDA
T_RDCL
3.2V
T_SDA
T_SCL
LF
RF
LR
RR
8.5V
FM_AGC
LEVEL
PROUT
INDR
INDL
RDDA
RDCL
IIC5.0V
SDA
SCL
D_GND
D_GND
PLL8.5V
D_GND
INAL
INAR
INAC
INAD
INBL
INBR
LF
RF
LR
RR
INPL
INPR
PLOUT
A_GND
A_GND
MAIN8.5V
33
C405 0.1
2
32 31
31 32
C404 0.1
1
A_VDDS
C
C330
100p
C
C9 10 16V
C11 10 16V
ANT1
29 30
C
5
A VSS
L305
27 28
C
6
6
0V
3.2V
R335 820 L304
26
R569 1K
VOUTR
C
C578 R581
10 16V 8.2K
C304 0.01
5
C
C303 0.01
4
C
34 33
24 25
R570 1K
C
C
36 35
R567 100K
C506
270p
R583
8.2K
R337 0
OR IN
REGULAT
_EN
N.C
XTAL I
S CLK OUT 1
XTAL O
M CLK O
A VDD
N.C
_BYP_C
3
22 23
C
7
+
8
GND
C
X301
11.2896MHz
2
C302
15p
1
PWR DN
LR CLK
38 37
R568 100K
0V
INPR
S CLK IN
L303
R336 220
-
L301
C301 15p
R333
820
R334 820
IC302
PCM3010DBR
PLOUT
INPR
C8 10 16V
C3 0.022
C
20 21
C406
0.01
INPL
18 19
R580
100K
4
C314
0.1
PROUT
C
C1
150p
OUT
C
L302
17
-
C576
0.1
12
16
C574
2.2 50V
3
C
C333
0.1
C2 47 16V
BL1
CCC-TUNER
880-2150A
D553
MA111
2
10 11
13
14 15
R577
3.9K
1
9
15 14
12 13
+
8.9V
8
10 11
OUT VCC
7
C
C325
1000p
C
9
R582
8.2K
17 16
0V
3.2V
C326 100p
FM_ANT
A_GND
AM_ANT
8
IC554
HA17558ATEL
6
7
C
C
5
19 18
C501
100p
C
R560
24K
R564
39K
4
6
C
+
21 20
5
C341
0.047
5
-
C
C13
22p
4
R586
8.2K
6
GND
C315 10 16V
VOUTL
VOUTR
R6
100K
3
C503
0.1
7
+
C322
0.1
5.0V
3
C311 10 16V
5.0V
C324 0.1
C318 10 16V
C
SUP1
2
R585
8.2K
0V
8
OUT
PROUT
C310 10 16V
2
-
8.9V
VOUTL
VREF1
VOUTR
VREF2
VCC2
VCC1
AGND2
AGND1
DEMP0
FMT0
DEMP1
FMT1
PDWN
TEST
SCK1
LRCK
VDD
BCK
DGND
DIN
DOUT
VINR
VCOM
23 22
OUT VCC
C323
0.1
C309 10 16V
VINL
1
R566
39K
IC552
HA17558ATEL
C312
0.1
24
C
C
C307
1
C319 0.1
C
L1
1
C
PLOUT
C502
100p
C
Main PWB(B2) section 2/3
RR
LR
3 RR
RF
3 RL
LF
3 FR
T_RDDA
T_RDCL
T_SDA
T_SCL
DSP_SCL
DSP_SDA
DSP_RST
L3 6.8uH
8.9V
5.0V
3.2V
R551 C551
56K(F) 10 16V
R552 C552
56K(F) 10 16V
R553 C553
56K(F) 10 16V
R554 C554
56K(F) 10 16V
R561 C558
220 2.2 50V
AUX_R
AUX_L
DSP_SDA
C16
0.047
C
R429 100
C
D505 MA729
SP_A
SP_B
D506 MA729
SP_C
D507 MA729
SP_DATA
To page 20
Main PWB 3/3
3 FL
1 TUN_RDDA
1 TUN_SDA
1 TUN_RDCL
1 TUN_SCL
1 DSP_SCL
1 DSP_SDA
1 DSP_RESET
D2
MA729
1 AUDIO 9V
1 ACC 5V
1 ACC 3.3V
1 GND
1 BUS AUDIO R+
1 BUS AUDIO R-
3 AUX_LCH
3 VREF
3 T-GND
1 SPAN-A
1 SPAN-B
1 SPAN-C
1 SPAN-DATA
To page 18
Main PWB 1/3
DSP_RST
8.9V
1 BUS AUDIO L-
1 BUS AUDIO L+
1 CDM_RCH
1 CDM_S-GND
1 CDM_LCH
3 AUX_RCH
To page 20
Main PWB 3/3
3 S-GND
1 F-GND
1 LEVEL_IN_R
1 LEVEL_IN_L
To page 18
Main PWB 1/3
Main PWB(B2) section 3/3
R410
100K
4
1
B/U 14V
1
C102 0.47
R112 1K
C
C104 0.47
R113 1K
RR
C
C105 0.47
R114 1K
FR
C
C103 0.47
R115 1K
13.3V
6.0V
C603 100p
C612 100p
C606 100p
C
C
C602 100p
C
C
L ch
VOAC1
CT
VOAC2
DD_REM
1
VHV
1
D/D-GND
To page 18
Main PWB 1/3
FILA2
1
FILA1
C206
100 63V
C
D202
MA4075H
1
P-GND4
OFFSET
-DET
13.9V
24 25
RL-
C
C125
1000p
C
C126
1000p
C
C127
1000p
C
C128
1000p
C
C129
1000p
C
C130
1000p
C
C131
1000p
J101
074-1214-00
C107
2.2 50V
D209
MA111
ACC
12.1V
R219
18K 1/4W
14.1V
11.6V
R102
27K
C116
1000p
D201
MA4180
R217
22K
Q207
KTC3875S
D205
MA111
R203
10K
R216
1K
0V
0V
RR-
6.9V
RR+
VCC1
6.9V
22 23
D206
MA111
PHONE
C
WXZ468RMP
8.0V
0V
C211
0.1
R211 13.7V
2.7K 1/4W
R210
2.7K 1/4W
R208
560
1/4W
1
CASE
NC
7
8.0V
VODC
6
8.0V
GND
5
48.0V
VIN
4
13.8V
3
L202
100uH
F201
Q205 1.3A
2SB1243
R209
47K
R218
47K
C207
47 63V
C
C210
0.1
2
RR-
FR-
13.9V
20 21
RR+
FR-
P-GND3
6.9V
0V
AC-GND
FR+
18 19
FR+
6.9V
16 17
3.7V
FR
RR
3.6V
14 15
MUTE
POW ON:3.4V
POW OFF:0V
3.7V
RL
2.0V
Q206
KTC3875S
R213
4.7K
R214
4.7K
D/D ON:0.7V
D/D OFF:0V
FR
S-GND
0V
FL
1
13.3V
REM
ILL ON:14.1V
ILL OFF:0V
ILL
14.0V
0V
L101
- 20 -
AUX IN
AUX-L
C205
100 35V
47.6V
D211
MA111
R215
10K
0.8V 1/4W
C
RL
ILL
D210
MA113
0.1V
C109
1 50V
FL
REM
12 13
3.7V
RIP
C106
10 16V
FL+
3.7V
FL+
10 11
8.6V
9
6.9V
FL-
P-GND1
8
0V
7
6.9V
6
FL-
RL+
RL+
6.9V
5
13.9V
STBY
4
ACC
R536
1K
R ch
11.4V
MUTE ON:0.7V
MUTE OFF:0V
PHONE
D504
HZU7.5B2
10
C
C613
390p
Q455
KTD1304
Q456
KTD1304
R456
22K
R101
10K
AUX-R
AUX-L GND
13.9V
R220
1.5K 1/4W
MUTE ON:0V/OFF:3.3V
AUX-R GND
D217
S5688G
BUS 14V
46.9V
13.9V
TM201
1
MUTE ON:1.7V
MUTE OFF:0V
REAR
L ch
R-L
L409
TM203
1
ILL
Q501
KRC106S
LINE OUT
R ch
R-R
L408
TM204
REM
L406
L407
C214 3300 16V
1
L405
RL
L201
220uH
C108 0.1
1
5.2V
D501
MA111
3
L ch
S-GND
L410
P
1
PHONE
R465
1K
C110
0.47
5.8V
1
AMP-MUTE
ACC
R537 8.2K
1
Q502
KRA106S
C
To page 18
Main PWB 1/3
R538 3.3K
R540
22K
SYS-MUTE
C
MUTE ON:1.8V
MUTE OFF:0V
D502
MA111
8.9V
8.3V
B/U 5.7V
2
4.9V
1
1
C
AMP-STBY
RL
R212
4.7K
R454
22K
1
RL-
AUDIO 9V
P-GND2
1
6.9V
F-GND
RR
Q208
2SB1243 47.6V
IC101
TB2906HQ
RL-
1
TAB
GND
0V
2
0V
T-GND
MUTE ON:0.7V
MUTE OFF:0V
C340
0.047
2
R464
1K
R462
330
Q503
KTC3875S
S-GND
C456
10 16V
FRONT
F-L
DC-DC
CONVERTER
R461
330
R455
22K
R449
220
C449
8200p
2
R460
330
C455
10 16V
C448
8200p
FR
R ch
F-R
IC202
RR
R450
220
C
2
C450
8200p
RR
C
2
C447
8200p
RL
1
FL
R459
330
C453
10 16V
R447
220
C
To page 19
Main PWB 2/3
L404
R413
100K
C
R419
22K(F)
C454
10 16V
R448
220
Q453
KTD1304
2
FL
R417
56K(F)
Q454
KTD1304
FL
4.6V
L403
C415 10 16V
VCC2
2
C411
0.047
0V
C
R421
22K(F)
VREF
C
2
C414 10 16V
C421
0.1
AUX_LCH
R453
22K
2
R416
56K(F)
FR
S-GND
R411
1K
3
R412
1K
2
C
1
R418
22K(F)
+
GND
5
L521 47uH
C542 10 16V
AUX_RCH
RCA-PIN-CORD
855-5535-50
R415
C413
56K(F) 10 16V
6
OUT
7
OUT VCC
C417
2.2 50V
0V
4
8
-
3
IC403
HA17558ATEL
2
1
IC402
HA17558ATEL
4.6V
4.6V
-
+
+
5
OUT
6
-
OUT VDD
C522 0.1
C541 10 16V
D503
HZU4.3B3
7
GND
8.9V
C416
2.2 50V
8
R414
C412
56K(F) 10 16V
C410
0.047
8.9V
+
L520
R420 22K(F)
R523
330
2
1
RL+
4
3
FL-
6
5
FL+
8
7
10
9
12
11
14
13
16
15
FR+
FRRR+
RRC
C132
1000p
14.0V
D203
1N5404
No.
1
3
5
7
9
11
13
15
Description
SP R/L(+)
SP F/L(-)
SP F/L(+)
SP F/R(+)
SP F/R(-)
SP R/R(+)
SP R/R(-)
BACK UP
No.
2
4
6
8
10
12
14
16
Description
SP R/L(-)
PHONE INT
ACC
N.C
REMOTE
ILLUMI
BACK UP(BUS)
GND
Clarion Co., Ltd.
Published by Service Dept.
Jan.2006
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan
Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan
Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703
Printed in Japan
Service Manual
In Dash 6disc CD Auto Changer
Mechanism(GI-X)
Model
929-0371-80
EXPLANATION OF IC
051-6711-20
051-3364-90
Terminal Description
pin 1: VDDP
pin 2: Reset
pin 3: Standby
pin 4: MiCS
pin 5: MiLP
pin 6: MiDio
pin 7: MiCK
pin 8: MiACK
pin 9: VDDT
pin 10: VSS
pin 11: SDo 0
pin 12: BCKo
pin 13: LRCKo
pin 14: SDi 0
pin 15: BCKi A
pin 16: LRCKi A
pin 17: Data
pin 18: SBSY
pin 19: SFSY
pin 20: TXo
pin 21: VDD
pin 22: CLOCK
pin 23: VSS
pin 24: io 0
NJU7771F15-TE2 1.5V Positive Voltage Regurator
Control (H= On) 1
Ground 2
N.C. 3
051-5452-90
5 Vin
4 Vout
BD5235G-TR
Precision Vlotage Down Detector 3.5V
VDD
OUTPUT 1
VDD
2
GND
3
Vout
5 C.T.
4 N.C.
Vref
GND
Terminal description
pin 1: OUTPUT
pin
pin
pin
pin
2: VDD
3: GND
4: N.C.
5: C.T.
CT
: N channel open drain output.
This terminal will output L, if the voltage of
VDD becomes lower than the setting voltage.
: Positive supply voltage.
: Ground.
: Not in use.
: Delay time capacitor.
pin 25: io 1
pin 26: io 2
pin 27: io 3
pin 28: Pio 4
pin 29: Pio 5
pin 30: Pio 6
pin 31: Pio 7
pin
pin
pin
pin
pin
pin
- M1 -
32: WE
33: RAS
34: CAS
35: OE
36: Po 11
37: Po 10
TC94A34FG-004
CD-ROM/MP3/WMA
Decoder
: - : Positive voltage supply.
: IN : Reset input.
: IN : Standby input.
: IN : Microcomputer I/F. Chip select input.
: IN : Microcomputer I/F. Latch pulse input.
:I/O: Microcomputer I/F. I2C-SDA.
: IN : Microcomputer I/F. Clock pulse input.
: O : Microcomputer I/F. Acknowledge output.
: - : Positive voltage supply.
: - : Ground.
: O : Audio I/F. Serial data output.
: O : Audio I/F. Bit clock output.
: O : Audio I/F. LR clock output.
: IN : Audio I/F. Serial data input.
: IN : Audio I/F. Bit clock input.
: IN : Audio I/F. LR clock input.
: IN : Sub Code I/F. The data input.
: IN : Sub Code I/F. Block sync.
: IN : Sub Code I/F. Frame sync.
: O : SPD I/F. Transmission terminal.
: - : Positive voltage supply.
:I/O: Sub Code I/F Clock pulse input/output.
: - : Ground.
:I/O: SRAM/DRAM I/F. Parallel data input/output.
:I/O: SRAM/DRAM I/F. Parallel data input/output.
:I/O: SRAM/DRAM I/F. Parallel data input/output.
:I/O: SRAM/DRAM I/F. Parallel data input/output.
:I/O: General-purpose I/O terminal. Parallel data
input/output.
:I/O: General-purpose I/O terminal. Parallel data
input/output.
:I/O: General-purpose I/O terminal. Parallel data
input/output.
:I/O: General-purpose I/O terminal. Parallel data
input/output.
: O : SRAM/DRAM I/F. Write enable.
: O : DRAM I/F. RAS output.
: O : DRAM I/F. CAS output.
: O : SRAM/DRAM I/F. Output enable.
: O : General-purpose output terminal.
: O : General-purpose output terminal.
929-0371-80
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
38: Po 9
39: Po 8
40: VDDM
41: SRMSTB
42: VDDT
43: AD 10
44: AD 9
45: AD 8
46: AD 7
47: AD 6
48: AD 5
49: AD 4
50: AD 3
51: AD 2
52: AD 1
53: AD 0
54: VSS
55: VDD
56: CKo
: Po 13
57: VDDX
58: Xo
59: Xi
60: VSSX
61: TEST
62: MiMD
63: VSSP
64: VCOi
051-9318-10
: O : General-purpose output terminal.
: O : General-purpose output terminal.
: - : Positive voltage supply.
: IN : Internal SRAM I/F. Standby input.
: - : Positive voltage supply.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: O : SRAM/FRAM I/F. Address output.
: - : Ground.
: - : Positive voltage supply.
: O : Clock output.
: O : General-purpose output terminal.
: - : Positive voltage supply.
: O : Crystal connection.
: IN : Crystal connection.
: - : Ground.
: IN : H = Test.
: IN : H = I2C, L = Normal.
: - : Ground.
: O : Control voltage output for VCO.
GLT4160L04P-60TC
Terminal Description
pin 1 : VCC
pin 2 : DQ 0
pin 3 : DQ 1
pin 4 : WE_
pin 5 : RAS_
pin 6 : NU
pin 7 : NEX
pin 8 : A 10
pin 9 : A 0
pin 10: A 1
pin 11: A 2
pin 12: A 3
pin 13: VCC
pin 14: VSS
pin 15: A 4
pin 16: A 5
pin 17: A 6
pin 18: A 7
pin 19: A 8
pin 20: NEX
pin 21: A 9
pin 22: OE_
pin 23: CAS_
pin 24: DQ 2
pin 25: DQ 3
pin 26: VSS
16M bit Dynamic RAM
: Positive supply voltage.
: Data input / output.
: Data input / output.
: Write enable.
: Row address strobe.
: Not in use.
: No existence.
: Address input.
: Address input.
: Address input.
: Address input.
: Address input.
: Positive supply voltage.
: Ground.
: Address input.
: Address input.
: Address input.
: Address input.
: Address input.
: No existence.
: Address input.
: Output enable.
: Column address strobe.
: Data input / output.
: Data input / output.
: Ground.
052-5070-91
T5AF4
TerminalDescription
pin 1: Vref L
pin 2: A VSS
pin 3: A VCC
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
4: LO CW
5: LO CCW
6: A MUTE
7: De-emphasis
8: E-EJ
9: P ON 1
10: NU
11: P ON 3
12: NU
13: NU
14: NU
15: NU
16: NU
17: NU
18: DSP SO
19: DSP SI
20: DSP SCK
21: FL TX
22: FL RX
23: SW 9V
24: PULL UP
25: VCC
26: X out
27: VSS
28: X in
29: PULL UP
30: RESET
31: TIME
32: NU
33: NC
34: NC
35: BU DET
36: SW 5
37: SBSY
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
38: PON 2
39: MODE CW
40: MODE CCW
41: U/D CW
42: U/D CCW
43: ALE
44: DR MUTE
45: SRAM STNDB
46: DSP RESET
47: DSP CS
48: DSP LAT
49: DSP ACK
50: LIMIT
51: EEP CS
52: EEP SK
53: EEP DI
54: EEP DO
55: HSSW
pin 56: HSSW 2
pin
pin
pin
pin
pin
pin
pin
pin
929-0371-80
- M2-
57: DSP REQ
58: DSP STNDB
59: NU
60: NU
61: BUC CLOCK
62: VSS
63: NMI
64: VCC
Mechanism Controller
: - : Reference voltage.
: - : Negative voltage supply for analog section.
: - : Positive voltage supply for the internal
analog section.
: O : Loading motor control signal output.
: O : Loading motor control signal output.
: O : The audio mute signal output.
: IN : De-emphasis ON command input.
: IN : Emergency Eject input.
: O : Power ON signal output.
: - : Not in use.
: O : Power ON signal output.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: O : Serial data output to the DSP IC.
: IN : Serial data input from the DSP IC.
: O : The clock pulse output to DSP IC.
: O : The serial data output for flash memory.
: IN : The serial data input for flash memory.
: O : 9V power supply control.
: IN : PULL UP
: - : Positive voltage supply.
: O : Crystal connection.
: - : Negative voltage supply.
: IN : Crystal connection.
: IN : PULL UP
: IN : Reset signal input.
: O : For Time base.
: - : Not in use.
: O : Not in use.
: O : Not in use.
: IN : Backup detection signal input.
: IN : The switch signal input.
: IN : Sub code block synchronous signal detection input.
: O : Power ON signal output.
: O : Mode motor control.
: O : Mode motor control.
: O : Holder control.
: O : Holder control.
: O : The address latch enable output.
: O : Drive mute signal output to the CD IC.
: O : SRAM standby signal output.
: O : Reset signal output to the DSP IC.
: O : Chip select signal output to the DSP.
: O : The latch pulse output to DSP IC.
: IN : DSP acknowledge.
: IN : Inside limit switch signal input.
: O : The chip select output to EEP-ROM.
: O : The clock pulse output to the EEP-ROM.
: IN : The serial data input from the EEP-ROM.
: O : The serial data output to the EEP-ROM.
: IN : It is used at the jitter measurement (the
speed is 2X, shock proof is through).
: IN : It is used at the jitter measurement (the
speed is 1X, shock proof is through).
: IN : DSP request input.
: O : DSP standby output.
: - : Not in use.
: - : Not in use.
: O : CD IC clock pulse output.
: - : Negative voltage supply.
: IN : Connect to VDD via a resistor.
: - : Positive voltage supply.
pin
pin
pin
pin
pin
pin
pin
65: BUS 0
66: BUS 1
67: BUS 2
68: BUS 3
69: CCE
70: CD RESET
71: T DATA
pin 72: T CLK
pin 73: T CLR
pin 74: NU
pin 75: NU
pin 76: NU
pin 77: NU
pin 78: FL BOOT
pin 79: TEST 1
pin 80: TEST 2
pin 81: TEST 3
pin 82: TEST 4
pin 83: REQ O
pin 84: I2C SDA
pin 85: I2C SCL
pin 86: ACC DET
pin 87: NU
pin 88: SW 1
pin 89: VCC
pin 90: SW 2
pin 91: VSS
pin 92: SW 3
pin 93: SW 4
pin 94: NU
pin 95: PT 1
pin 96: PT 2
pin 97: PT 3
pin 98: PT 4
pin 99: PT 5
pin100: Vref H
:I/O: CD IC Data input / output.
:I/O: CD IC Data input / output.
:I/O: CD IC Data input / output.
:I/O: CD IC Data input / output.
: O : The chip enable signal output.
: O : The reset pulse output to the CD IC.
: O : The display data output for the test mode
indication.
: O : The test clock output.
: O : The clear signal output for the test mode
indication.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: - : Not in use.
: IN : Flash memory control.
: IN : For the test.
: IN : For the test.
: IN : For the test.
: IN : For the test.
: O : Transmit request signal output.
:I/O: I2C serial data input/output.
:I/O: I2C serial clock input/output.
: IN : ACC detection signal input.
: - : Not in use.
: IN : The switch signal input.
: - : Positive voltage supply.
: IN : The switch signal input.
: - : Negative voltage supply.
: IN : The switch signal input.
: IN : The switch signal input.
: - : Not in use.
: IN : The photo sensor signal input.
: IN : The photo sensor signal input.
: IN : The photo sensor signal input.
: IN : The photo sensor signal input.
: IN : The photo sensor signal input.
: - : Reference voltage.
- M3 -
929-0371-80
DISASSEMBLY
How to remove "CD-PWB-ASSY"
How to remove "DISCHOLDER UNIT"
1. Add +5V to "U+" terminal of UD-MOTOR-ASSY,then
SIDE-P-ASSY-F moves outside of CD-PWB.
2. Release four FPCs.
3. Remove three screws
4. Remove the washer.
5. Remove SW-H-PLATE and SW-LINK, and remove CDPWB-ASSY.
1. Remove eight screws.
2. Remove the FPC.
1
1
3
2
4
5
1
SIDE-P-ASSY-F
*
2
3. Remove UPPER UNIT ASSY.
4. Remove two C-RINGs, and remove DISCHOLDER
UNIT.
CD-PWB-ASSY
When assembling, match
SW LINK to three switches.
3
SW-LINK
DISCHOLDER UNIT
Switches
4
929-0371-80
- M4-
How to remove "N-DRIVE UNIT"
How to remove "LO-MOTOR-S-ASSY"
1. Remove the screw and DRIVE SPRING-A.
2. Rotate N-DRIVE UNIT internally.
3. Remove the washer, and remove N-DRIVE UNIT.
1. Remove two screws and DRIVE CHASSIS-B.
2. Remove the screw of the bottom side.
3. Remove the solder of SENSOR-L-FPC, and remove LOMOTOR-S-ASSY.
1
N-DRIVE UNIT
DRIVE CHASSIS-B
1
2
2
3
3
LO-MOTOR-S-ASSY
SENSOR-L-FPC
How to remove "UD-MOTOR-ASSY"
How to remove "M-MTR SUB ASSY"
1. Remove two screws, and remove M-MTR SUB ASSY.
1. Remove the screw of the bottom side, and remove UDMOTOR-ASSY.
M-MTR SUB ASSY
1
UD-MOTOR-ASSY
- M5 -
1
929-0371-80
OPERATION
Discholder
MOT2 (Mode Motor)
S1 of CD-PWB (Mode Plate)
S2 of CD-PWB (Mode Plate)
S3 of CD-PWB (Mode Plate)
Drive Unit
MOT3 (UP/DW-Motor)
S5 of SENSOR-U-FPC (Sutter)
S4 of CD-PWB (Holder)
MOT1 (Loading Motor)
Loading Roller
Shutter
PT3 of SENSOR-L-FPC
PT2 of SENSOR-L-FPC
PT1 of SENSOR-L-FPC
IC10 of CD PWB
Q1 of CD PWB
Function of Switches
Function of Mechanism
[S1,2,3]
Detect a home position of mode plate.
Detect mode plate position by combination of on and
off.
[S4]
Detection of initial position of holder.
Initial position:S4-ON,IC10-bright.
[S5]
Opening/closing detection of shutter.
OFF:Close, ON:Open
[DISC HOLDER]
Six holders.
(Related motor:UP/DW-Motor)
[DRIVE UNIT]
Chukking of a play disc.
(Related Motor:Mode motor)
[LOADING ROLLER]
Disk is stored/ejected by rotation.
(Related Motor:Laoding motor)
[SHUTTER]
Shutter at disc insertion.
(Related Motor:Mode Motor)
Function of Motors
Function of Photo sensors
[MOT1 LOADING MOTOR]
Rotation of loading roller.
(Related Sensor:PT1,2,3,Q1)
[MOT2 MODE MOTOR]
Rotation of mode plate.
Chukking disc.
Opening/closing holder.
Movement of loading/ejecting roller.
Opening/closing shutter.
(Related Sensor:S1,2,3)
[MOT3 UP/DW-MOTOR]
Going up and down of disc holder.
Selection of disc holder.
(Related Sensor:S4,IC10)
929-0371-80
[PT1]
Detection of start loading and passing of disc.
Bright:no DISC, Dark:DISC
[PT2]
Detection of finish eject and passing of disc.
Bright:no DISC, Dark:DISC
[PT3]
Detection of store and passing of disc.
Bright:no DISC, Dark:DISC
[Q1]
Detection of passing of disc.
Bright:no DISC, Dark:DISC
[IC10]
Detection of holder position
- M6-
EXPLODED VIEW/PARTS LIST
Main section
D2
27
27
D1
9
27
34 33
4
27
to C2
26
to C4
to C3
17
to D3
to B1
8
to B2
10
26
18
12
3
to C1
5
22
to A6
2
to A7
* 30
* 31
* 32
to A3
C3
C2
to A2
C4
to A5
to A4
6
to
D2
27
1
7
B1
35
19
B2
23
33 34
to
D1
A3
A1
13
16
23
A5
A2
* 24
C1
A6
A7
36
to D3
A4
11
15
37
27
* 28
29 *
21 14
* 25
20
23
*28
* Do not reuse the following parts.
(No.24,25,28,29,30,31,32)
NO.
PART NO.
DESCRIPTION
Q'TY
NO.
PART NO.
DESCRIPTION
Q'TY
1
966-1756-24 LOWER UNIT ASSY
1
20
621-1636-24 SW LINK
1
2
966-0667-21 DISC STP-ASSY L
1
21
621-1765-20 UD-GEAR-D
1
3
966-0668-22 DH-SEL-ASSY S
1
22
621-1715-20 FPC-STOPPER
1
4
966-0669-22 DH-SEL-ASSY R
1
23
716-1850-01 SCREW(M2.0x2.0)
4
5
966-0670-22 DS-SP-ASSY L
1
24
716-1850-02 SCREW(M2.0x2.0)
1
6
966-1760-21 DS-SP-ASSY R
1
25
716-1851-02 SCREW(M2.0x3.0)
1
7
966-0672-21 REAR-P-ASSY
1
26
716-3450-00 SCREW(M1.7x2.0)
2
8
966-1753-91 N-DRIVE-CH UNIT
1
27
716-3451-01 SCREW(M1.7x2.5)
8
9
966-1764-21 UPPER UNIT ASSY
1
28
746-0761-00 WASHER
2
10
HBS-566-100 DISC HOLDER UNIT
1
29
744-0045-01 C-RING
2
11
966-1771-21 SLIDE-P-ASSY F
1
30
347-7271-00 FPC SHEET
1
12
966-0709-21 SLIDE-P-ASSY
1
31
347-7275-00 PROTECT SHEET
1
13
HBS-564-100 CD-PWB-ASSY
1
32
347-7276-00 FPC-SHEET C
1
14
620-1640-20 SW-H-PLATE
1
33
800-4921-60 VINYL-COAT-WIRE
1
15
620-1778-20 GAP PLATE F
1
34
802-4921-60 VINYL-COAT-WIRE
1
16
620-1662-21 GAP PLATE R
1
35
345-5824-00 RUBBER PART
1
17
620-1685-21 DS-PLATE L
1
36
621-1763-20 LOADING GUIDE B
1
18
620-1686-20 DS-PLATE R
1
37
716-1859-01 IT SCREW(M1.7 x 2)
1
19
621-1760-21 DISC STOPPER R
1
- M7 -
929-0371-80
Lower unit assy section
15
to A1
18
11
12
to A2
15
to A3
18
6
7
2
5
17
13
3
to
A4
14
17
9
to A5
A1
A4
1
19
10
A5
4
A2
A3
A7
A6
15
to A7
to A6
16
8
NO.
Q'TY
NO.
1
966-1757-21 LOWER-C-ASSY
PART NO.
DESCRIPTION
1
11
620-1771-22 CAM GEAR
PART NO.
DESCRIPTION
Q'TY
1
2
966-0658-21 DH-SP-ASSY A
1
12
620-1624-24 GEAR COVER
1
3
966-1758-20 DS-SP-ASSY A
1
13
621-0732-21 M-GEAR B
1
4
966-0660-22 DH-SP-ASSY S
1
14
621-0733-20 M-GEAR C
1
5
966-0661-22 DH-SP-ASSY R
1
15
716-1850-01 SCREW(M2.0x2.0)
5
6
966-0677-23 D-SHT PL-B-ASSY
1
16
716-3451-01 SCREW(M1.7x2.5)
2
7
966-0659-21 DH-SP-ASSY B
1
17
746-0761-00 WASHER
2
8
966-1759-00 DS-SP-ASSY B
1
18
746-0768-00 WASHER
2
9
HBS-546-100 M-MTR SUB ASSY
1
19
750-6756-00 SW-L-SPRING
1
10
HBS-568-100 UD-MOTOR-ASSY
1
929-0371-80
- M8-
[ Grease Point ]
* Grease: SANKOL FG-87HSR
Put grease on the surface
Put grease on the reverse side
Put grease on the both sides
Put grease on the edge
1
2
3
7
5
6
8
11
S
4
P
2
L
- M9 -
929-0371-80
N-Drive-CH unit section
12
13
1
10
8
* 20
6
A2
to A2
A1
to A1
11
*19
5
9
14
11
A3 A4
2
21
16
to B1
11
7
B1
11
4
4-1
* 18
3
to A3
to A4
*18
15
11
*
17
* Do not reuse the following parts.
(No.17,18,19,20)
NO.
PART NO.
DESCRIPTION
Q'TY
NO.
PART NO.
DESCRIPTION
Q'TY
1
HBS-565-100 N-DRIVE UNIT
1
11
716-3450-00 SCREW(M1.7x2.0)
6
2
HBS-567-100 LOADING-U-ASSY
1
12
716-3459-01 SCREW(M1.7x2.0)
1
3
HBS-556-100 LO-MOTOR-S-ASSY
1
13
750-6761-20 DRIVE SPRING A
1
4
HBS-552-100 L-SENSOR-S-ASSY
1
14
345-5868-00 RUBBER PART
1
-----------
1
15
620-1651-20 S-PWB-PLATE
1
1
16
750-6754-20 LO-ES-SPRING B
1
4-1
5
SENSOR-L-FPC
966-0676-20 D-SHT LK-A-ASSY
6
966-1755-00 DRIVE-CH A ASSY
1
17
345-5424-01 SEN-FPC GUIDE
1
7
620-1681-21 DRIVE CHASSIS B
1
18
716-1859-01 SCREW(M1.7x2.0)
2
8
620-1672-21 DR-SUPPORT-PL
1
19
744-0039-00 E-RING
1
9
620-1680-20 D-SHIFT COVER
1
20
746-0870-00 WASHER
1
10
622-1743-20 D-SHIFT ROLLER B
1
21
716-3538-00 SCREW(M1.7x2.0)
1
929-0371-80
- M10-
[ Grease Point ]
* Grease A: SANKOL FG-87HSR
* Grease B: SANKOL CFD-006MBL
1
B
Put grease on the surface
Put grease on the reverse side
Put grease on the both sides
Put grease on the edge
A
5
A
6
A
A
Surface of PIN
A
A
B
A
Surface of Spring
7
8
9
A
A
B
10
A
A
- M11 -
929-0371-80
Upper unit assy section
to A1
* Do not reuse the following parts.
(No.7,8,10)
2
*7
NO.
to A2
7-1
1
4
3
A1
9
5
6
*10
PART NO.
*8
966-1761-21 UPPER-CHA-ASSY
1
2
966-1765-20 LO-SHIFT A ASSY
1
3
966-0700-22 LO-SHIFT B ASSY
1
4
966-0701-21 LO-SHIFT ASSY
1
5
966-1766-20 SHUTTER-PL-ASSY
1
6
966-1763-20 SHUTTER ASSY
1
7
HBS-553-100 U-SENSOR-S-ASSY
1
-----------
SENSOR-U-FPC
1
8
347-7272-00 RATTLE SHEET
1
9
750-6755-21 SHUTTER SPRING
1
10
746-0870-00 WASHER
1
[ Grease Point ]
* Grease: SANKOL FG-87HSR
Put grease on the surface
Put grease on the reverse side
Put grease on the both sides
Put grease on the edge
1
2
3
5
6
929-0371-80
Q'TY
1
7-1
A2
DESCRIPTION
- M12-
4
ELECTRICAL PARTS LIST
CD PWB(BM1) section
REF No.
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C38
C39
C40
C42
C43
C44
C45
C46
C47
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C59
C60
C61
C62
C63
C64
C65
C66
C67
C68
C70
C71
C72
PART No.
042-0672-00
166-1011-50
168-1042-78
178-1052-78
042-0671-01
168-1045-56
168-1032-55
168-1045-56
178-1052-78
168-1045-56
168-1045-56
178-1052-78
178-1052-78
042-0671-01
168-1032-55
178-1052-78
168-1042-78
178-1052-78
168-1045-56
042-0671-01
168-1042-78
168-1045-56
168-4732-78
166-4701-50
168-4732-78
166-4711-50
168-1532-55
166-4711-50
168-1045-56
168-6822-55
168-1032-55
168-3332-78
168-4722-55
168-1042-78
168-1045-56
168-1532-55
168-1045-56
168-1522-55
168-1045-56
166-6811-50
166-6801-50
178-1052-78
042-0671-01
042-0671-01
178-1052-78
168-1042-78
178-1052-78
178-1052-78
042-0671-01
168-1042-78
168-1045-56
178-1052-78
168-1032-55
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
168-1045-56
DESCRIPTION
25V 47uF TA
100pF CH
16V 0.1uF
1uF
10V 47uF TA
0.1uF Z
0.01uF K
0.1uF Z
1uF
0.1uF Z
0.1uF Z
1uF
1uF
10V 47uF TA
0.01uF K
1uF
16V 0.1uF
1uF
0.1uF Z
10V 47uF TA
16V 0.1uF
0.1uF Z
0.047uF K
47pF CH
0.047uF K
470pF CH
0.015uF K
470pF CH
0.1uF Z
6800pF K
0.01uF K
0.033uF K
4700pF K
16V 0.1uF
0.1uF Z
0.015uF K
0.1uF Z
1500pF K
0.1uF Z
680pF
68pF CH
1uF
10V 47uF TA
10V 47uF TA
1uF
16V 0.1uF
1uF
1uF
10V 47uF TA
16V 0.1uF
0.1uF Z
1uF
0.01uF K
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
0.1uF Z
REF No.
C73
C74
C75
C81
C82
C83
C85
C86
C87
C91
CCT1
CCT2
CCT3
CCT4
D1
D1
D2
D3
D3
D4
D4
IC1
IC2
IC3
IC4
IC5
IC6
IC8
IC9
IC10
IC11
IC12
J1
J2
J3
J4
J5
Q1
Q2
Q3
Q6
Q7
Q8
Q9
Q10
Q11
Q12
Q20
R1
R2
R3
R4
R5
R6
R7
R8
R10
R11
R12
R13
R14
R15
R16
PART No.
178-1052-78
168-1045-56
168-2222-55
166-1007-50
166-1007-50
178-1052-78
178-1052-78
166-1201-50
042-1702-90
168-1032-55
050-0145-59
050-0145-54
050-0145-54
050-0145-55
001-4301-14
001-0529-14
001-0367-91
001-4301-16
004-0529-16
001-4301-18
001-0529-18
051-6399-00
052-5070-91
051-6711-20
051-6060-08
051-5452-90
051-9318-10
051-9402-78
051-6072-08
051-5833-00
051-3364-90
051-3364-90
074-1237-69
074-1201-65
074-1138-56
074-1100-61
074-1201-61
060-0252-01
125-0021-91
198-3018-00
131-1188-50
125-2027-91
131-1427-00
131-1188-50
125-2027-91
125-0021-91
125-2027-91
131-1427-00
119-4731-15
119-2211-15
119-2211-15
119-1041-15
119-4731-15
119-2211-15
119-2211-15
119-2211-15
032-0140-16
032-0140-96
119-2231-15
119-4711-15
119-2221-15
119-1031-15
119-0000-05
DESCRIPTION
1uF
0.1uF Z
2200pF K
10pF CH
10pF CH
1uF
1uF
12pF CH
6.3V 100uF
0.01uF K
1/16W 22 ohm x4
1/16W 47k ohm x4
1/16W 47k ohm x4
1/16W 10k ohm x4
HZU 3.0B1
MA8030-L
1SS226
HZU 3.3B1
MA8033-L
HZU 3.6B1
MA8036-L
TC94A15F
T5AF4
TC94A34FG-004
BD7961FM-E2
BD5235G-TR
GLT4160L04P-60TC
BR93L56RFVM-W
BD7931FE2
GP1S093HCZ
NJU7771F15
NJU7771F15
19PIN
15P
6P
SOCKET 11P
11P SOCKET
PT4850F
DTA114EUA
2SK3018
2SB1188PQR
DTC114EUA
2SB1427
2SB1188PQR
DTC114EUA
DTA114EUA
DTC114EUA
2SB1427
1/10W 47k ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 100k ohm
1/10W 47k ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 220 ohm
1/10W 180k ohm F
1/10W 120k ohm F
1/10W 22k ohm
1/10W 470 ohm
1/10W 2.2k ohm
1/10W 10k ohm
1/10W 0 ohm JW
REF No.
R17
R18
R19
R20
R21
R22
R23
R24
R25
R26
R27
R28
R29
R30
R31
R32
R33
R34
R35
R36
R37
R38
R39
R40
R41
R42
R43
R44
R45
R46
R48
R49
R50
R51
R52
R53
R54
R55
R56
R57
R58
R59
R60
R61
R62
R64
R65
R66
R71
R72
R73
R77
R82
R83
R85
R86
S1
S2
S3
S4
X1
X3
PART No.
119-4731-15
119-2231-15
119-2231-15
119-4721-15
119-4731-15
119-4731-15
119-4731-15
050-0145-58
119-4721-15
119-4721-15
117-7511-15
116-3391-15
032-0145-73
119-1041-15
119-6811-15
119-1041-15
119-6811-15
119-1041-15
117-5611-15
119-1041-15
119-1041-15
119-3321-15
119-1051-15
119-0000-05
119-1041-15
119-5621-15
119-4731-15
119-2231-15
119-8231-15
119-3341-15
119-2231-15
116-1001-15
119-1011-15
119-6811-15
117-7511-15
116-5611-15
119-1041-15
119-1041-15
119-1041-15
119-1041-15
119-1041-15
116-1511-15
119-4731-15
119-4731-15
119-1051-15
032-0140-53
119-2211-15
032-0140-62
119-1011-15
119-1011-15
119-1011-15
119-0000-05
119-1011-15
119-1031-15
119-1021-15
119-2231-15
013-7416-50
013-7416-50
013-7416-50
013-7415-50
061-3534-90
060-1545-90
DESCRIPTION
REF No. PART No.
DESCRIPTION
1/10W 47k ohm
1/10W 22k ohm
1/10W 22k ohm
1/10W 4.7k ohm
1/10W 47k ohm
1/10W 47k ohm
1/10W 47k ohm
1/16W 2.2k ohm x4
1/10W 4.7k ohm
1/10W 4.7k ohm
1/8W 750 ohm
1/4W 3.3 ohm
1/2W 6.8 ohm
1/10W 100k ohm
1/10W 680 ohm
1/10W 100k ohm
1/10W 680 ohm
1/10W 100k ohm
1/8W 560 ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 3.3k ohm
1/10W 1M ohm
1/10W 0 ohm JW
1/10W 100k ohm
1/10W 5.6k ohm
1/10W 47k ohm
1/10W 22k ohm
1/10W 82k ohm
1/10W 330k ohm
1/10W 22k ohm
1/4W 10 ohm
1/10W 100 ohm
1/10W 680 ohm
1/8W 750 ohm
1/4W 560 ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 100k ohm
1/10W 100k ohm
1/4W 150 ohm
1/10W 47k ohm
1/10W 47k ohm
1/10W 1M ohm
1/10W 2.2k ohm F
1/10W 220 ohm
1/10W 1k ohm F
1/10W 100 ohm
1/10W 100 ohm
1/10W 100 ohm
1/10W 0 ohm JW
1/10W 100 ohm
1/10W 10k ohm
1/10W 1k ohm
1/10W 22k ohm
SW SPVL110200
SW SPVL110200
SW SPVL110200
SPVG110400
16.92MHz
20MHz
Sensor-L-PFC(BM2) section
REF No. PART No.
PT1
DESCRIPTION
060-0252-01 PT14850F
REF No. PART No.
PT2
060-0252-01 PT14850F
PT3
DESCRIPTION
051-5833-00 GP1S093HCZ
Sensor-U-PFC(BM3) section
REF No. PART No.
LED1
LED2
DESCRIPTION
001-7077-00 GL4804
001-7077-00 GL4804
REF No. PART No.
LED3
DESCRIPTION
001-7077-00 GL4804
- M13 -
REF No. PART No.
S5
DESCRIPTION
013-7417-50 ABC1122P161
929-0371-80
929-0371-80
Sensor-L-FPC
Sensor-U-FPC
Drive Unit
CD-PWB
CD3.3V
2SB1427
Q8, Q20
AUDIO
- M14DRAM
GLT4160L04P
IC6
IC12
NJU7771
IC11
NJU7771
DECORDER
TC94A34FG
IC3
CPU
T5AF4
IC2
BD5235G
Q6 : 2SB1188
Q7 : DTC114EUA
Q10 : DTC114EUA
Q11 : DTA114EUA
L-CH
GND
R-CH
BLOCK DIAGRAM
CIRCUIT DIAGRAM
CD PWB(BM1) section
Sensor-L-FPC(BM2) section
Sensor-U-FPC(BM3) section
S5
SHUTTER
GND
2
SW5
1
R45 82K
D2
1SS226
R49
10 1/4W
C55 1
C
C56
47 10V TAN
TRO
FOO
DMO
TP77
SBAD
TP78
FE
TP79
RFDC
C
RFZI
AVSS3
RVDD3 40
FCS- 4.3V
R19 22K
2.0V
TRK- 4.5V
3.3V
TRK+ 5.0V
0V
FCS+ 4.5V
0V
3.3V
EQSET 39
RFO 37
RFDCI
36
AGCI
35
INVSEL
34
TESTR 33
94 AIN
VMDIR 32
20 21
PVSS3
DTCN
DTCP
VCOREF
PVREF
18 19
22 23
RFI
24 25
27
C42 0.1
C
C43 0.015
C46
0.1
C
C
GND
5
C
6
VREF
7
8
F
FCS-
9
E
10
TRK-
11
VCC
12
TRK+
13
PD
14
FCS+
15
VR
1.7V
C44 0.1
SP-
4.0V
SP+
5.0V
SL+
4.3V
SL-
4.5V
3 SP4 SP+
5 SL+
6 SL-
MOT5
SLED
C
C
C45 1500p
C49
1
3.3V
C
5
C
C
C63 0.1
C
Sensor-U-FPC(BM3)
929-0371-80
A4
24
DQ4
DQ2
DQ3
BCKIA
/WE
32
R23
47K
/WE
N.C.
31
N.C.
28
N.C.
DQ4
27
N.C.
DQ3
26
30
DQ2
25
29
VSS
DQ1
24
VDD
CLCK
22
/CAS
21
SPDIF(N.C.)
/OE
20
REQ
SDI
SBSY
LRCKO
A10R
A0
A1
A2
A3
22 23
A8
A0
A7
A1
A6
A2
A5
A3
A4
DSP-REQ
C21 0.1
/OE
/CAS
/RAS
VCC VSS
C
C25 0.1
C
19
2
3
4
A10R
5
6
C
7
C
SRMSTB
39 40
/RAS
C64
0.1
A9
8
C65
0.1
/OE
N.C.
9
A10R
/RAS
10
A9
/WE /CAS
12 11
47 48
45 46
/RAS
41 42
43 44
/WE
A8
37 38
N.C.
35 36
BCKO
33 34
N.C.
A7
20 21
VSS
DQ1
17 18
49
A4
SDO
DQ2
15 16
50
A3
N.C.
DQ1
A6
13 14
51
A2
VSS
LRCKIA
VCC
1
52
A1
A1
53
A0
A2
54
VSS
A3
55
A0
56
CKO
VDD
VDDM
SRMSTB
A5
DQ4
DQ3
/CAS
/OE
A9
A8
A7
A6
A5
A4
C
C66
0.1
C
C
C67
0.1
C61
R62 1M 0.01
C
59
XI
57
60
VSSX
58
61
TEST
XO
63
62
VDDT
VDDT
IC3
TC94A34FG-004
DQ4
R82 100
VSSP
MIACK
DATA
17
Q12
DTC114EUA
MIMD
2
/MICK
SFSY
LRCKO
MIDIO
18
BCKO
/MILP
19
LRCKI
AOUT
AIOR
4
CCT3
47K x4
A9
5
BCKI
A8
/MICS
6
MIACK
A7
7
/MICK
STANDBY
8
MIDIO
A6
9
MOCCW
R15
10K
/MILP
/RESET
10
/MICS
A5
12 11
DSP-STB
VDDP
14 13
/DSP-RESET
4
IC6
GLT4160L04
3
1
R1 47K
VCOI
64
RCE
0V
VDDX
VSSX
R65
220
C
RCLK
23
3.3V
C75
2200p
IC11
NJU7771
5
VSSP
RDI
C
C74
0.1
C68
0.1
RDO
0V
CD-9V
0V
R22 47K
C71
0.1
C
PON3
VDD3.3V
DSP1.5V
3
C87 100 6.3V
2
C73 1
1
R83
10K
R85 1K
3
C70 0.1
2
C24 47 10V TAN
C72 0.1
1
C
C52
1
C
4
IC12
NJU7771
C50
47 10V TAN
C
C35 0.01
R46
330K
R43
47K
C51
47 10V TAN
C
C31
0.015
R44
22K
C
C39
4700p
16 15
59 60
57 58
55 56
3.3V
MOT4
SPINDLE
C47
680p
C
BUCK
3.3V
LIMIT
2 LIMIT
3.3V
C
DSP-STB
To Pick up
R48
22K
26
SLCO
16 17
VCOF
LPFN
LPFO
TMAX
TMAXS
14 15
R42 5.6K
R61 47K
DATA
SFSY
C
C22
1
CLCK
12 13
PDO
10 11
PVDD3
9
C28 47p
7
0V
6
RFRPI
30
B
4
0V
5
R21 47K
4
DATA
3
SFSY
2
VDD3
1
ARSEL
8
99 LRCKO
AWRC
RFEQO 28
IO1A(LOCK)
AVDD3 29
98 AOUT
SBSY
97 BCKO
IO0A
RESIN
LD
3
1 GND
LIMIT
C
VRO 31
96 EMPH(N.C.)
A
2
J3
074-1138-56
C48
68p
1.3V
C
PNSEL 38
C54
1
IC1
TC94A15F
93 BCKI
TP71
IPF
R18 22K
1
R50
100
LDO 41
86 BUS2
VSS3
R72 100
2.0V
MDI 42
85 BUS1
CLCK
AOUT
C38
0.033
1.6V
RFRP
RFDC
2.0V
1.6V
FEI
TEI
SBAD
1.6V
AVDD3
TRO
FOO
FMO
VREF
DMO
IO2A(RFGC)
TEZI
0V
3.3V
TP73
IO3
TP75
IO2
IO3A(TEBC)
0V
FGIN
MONIT(SEL)
VDD3
VSS3
XVSS3
TESIN
XI
RVSS3 43
MCK
LIMIT
RDI
RDO
FNI2 44
83 VSS5
2.0V
TP81
FTE
0V
R20 4.7K
0V DSP-REQ
53 54
82 ZDET
C
77
FNI1 45
AIN
DRMUT
FMO
C
C26
0.1
63 64
0V
51 52
LIMIT
MILP
FPI2 46
2.0V
C60
1
R64 2.2K (F)
3.3V
50
49
FPI1 47
C
UCCW
C
C82
10p
R38
3.3K
CCT4
10K x4
R71 100
C62
0.1
UCW
XO
C8
0.1
C
C6 0.1
C11 0.1
C
BCKO
FTE 50
80 LO
0V
- M15 -
52 51
TPI 48
DQ2
R53
560 1/4W
54 53
TNI 49
C33
0.1
/MILP
MO-
56 55
95 LRCKI
75
73 74
67 68
69 70
71 72
BUS0
61 62
65 66
BUS1
3.3V
3.3V
3.3V
MICS
MIACK
48
47
3.3V
3.3V
DSP-RESET
SRMSTB
45
46
3.3V
0V
ALE(N.C.)
43
44 DR-MUTE
3.3V
42 UCCW
0V
MOCCW
UCW
41
40
0V
0V
39 MOCW
SBSY
38 PON2
37
0V
0V
SW5
36
B/U-DET
EMU1(N.C.)
34
35
EMU0(N.C.)
32
33
XIN
MICOM-RESET
AM1
RCLK
RCE
TP22 BOOT
78
TEST1 79
FL-BOOT
TEST2 80
TEST3 81
R24
2.2K x4
83
I2C-REQ
TEST4 82
84
I2C-SDA
3.3V
85
I2C-SCL
ACC-DET 86
87
0V
3.3V
VCC 89
SW1 88
3.3V
3.3V
SW2 90
VSS 91
SW3 92
PT1
94
95
PT3
PT2
SW4 93
98
97
96
PT4
100
3
4
5
LRCKI
76
3.3V
58 57
92 EMPHI
AIN
3.3V
BUS3
BUS2
60 59
79 DVR
/CCE
3.3V
62 61
91 VDD5
BCKI
3.3V
2.0V
C
81 DVSS3
/CDIC-RST
3.3V
64 63
DQ3
3
RCE
78 DVDD3
R52
750
R27
750
4
C20 1
TP40 TCLR
TP38 TDATA
3.3V
66 65
DQ1
LED3
RCLK
MIACK
5
GND
RDI
/MICS
LED2
1.6V
C
4
R41 100K
/DSP-RESET
6
1.6V
X3
20MHz
SRMSTB
7
MO-
R60 47K
MO-
MO+
C57
0.1
8
0V
J2
074-1201-65
90 RST
TP42 TCLK
3.3V
68 67
DVSS3
77 RO
100
DOUT
3.3V
70 69
SFSY
LED3
MO+
/CDIC-RST
C
72 71
DATA
LED2
9
R7
220
R35
560
11
MO+
3
74 73
89 CCE
PT3
C
LED1
2
75
88 BUCK
/CCE
C86
12p
XVDD3
3.3V
O3+
O1+
SL+
R86 22K
O4+
O3O1-
O4O2-
O2+
DMO
FOO
FMO
TRO
C
3.3V
J5
074-1201-61
GND 10
MOT2
MODE
15 14
Q10
DTC114EUA
PT3
LED1
17 16
LO-
3.3V
0V
MOCW
1
VCC
R4 100K
PHOT3
LO+
AM1
C
2
RDO
LED SW
31 TIME
3
GND
HSW1
FRXD
C2 100p
LED4
FTXD
R6 220
4
HSW2
0V
LOM-
R25 4.7K
PT2
0V
0V
MICK
TP4
MP
5
TP33
FTXD
TP34
FRXD
0V
DSP-REQ
28
LOM-
R59
150 1/4W
PT1
3.3V
DSP-STB
MIDIO(SI)
MIDIO(SO)
29
6
VSS
30
7
LOM+
NMI
BUCK
R26 4.7K
LOM+
/MICK
3.3V
VCC
IC2
T5AF4
XOUT
VSS
8
BUS0
PON3
26
PHOT2
BUS1
27
9
BUS2
PON1
19 18
GND
3.3V
C
MIDIO
3.3V
BUS3
21 20
10
E-EJECT
R16 0
PHOT1
E
Q11
DTA114EUA
A
K
C
E
MOT1
LOADING
A
J4
074-1100-61
GND 11
PT2
0V
IC10 GP1S093HCZ
Sensor-L-FPC(BM2)
K
/CCE
13 12
C
/CDIC-RESET
A-MUTE
DE-EMP( OR PRODUCT MODE)
11 10
R32 100K
TCLK
TDATA
23 22
1
2
R11 120K(F)
3
5
IC5
BD5235G
4
3.3V
3.3V
99
1
R37 100K 3.3V
R5 47K
LOCCW
6
R40 0
R14 2.2K
LOCW
1
TCLR
7
0V
AVSS
5
LRCKO R73 100
8
0V
R36 100K
9
R34 100K
VREFL
AVCC
25 24
R10
180K(F)
2
G
S
3.3V
PT5
VREFH
0V
Q1
PT4850F
Q3
2SK3018
D
CCT1
22 x4
PT3
6
IC8
BR93L56RFVM
R17 47K
TP65 T1
3.3V
TP66 T2
TP67 T3
3.3V
3.3V
TP68 T4
3.3V
S1
S2
S3
S4
CCT2
47K x4
R58 100K
R54 100K
R55 100K
R57 100K
R56 100K
R30 100K
PT2
7
C
87 BUS3
BUCK
PT1
C15
0.01
BUS3
8
C30
470p
84 BUS0
BUS2
3.3V
PT1
76
3.3V
BUS1
C
C91 0.01
C
Drive Unit
C34
6800p
C
2.0V
IPF
FCS-
FCS+
TRK+
R66
2.2K (F)
Q9
2SB1188
C
C
UCCW
UCW
MOCW
MOCCW
18
C32
470p
C29
0.047
BUS0
C10
0.1
SCL
Q2
DTA114EUA
C
19
16 17
SP+
14 15
SPR8
220
To Main PWB
MO+
3.3V
TP11
GND
21 20
SL-
CNT5
12 13
23 22
GND CNT6
IN2
VM2
10 11
25 24
VM1
9
IN3
8
RGND
7
IN4
6
27 26
IN1
3.3V
5
IN6R R2-B
MUTE
R2OUT
4
29 28
C27
0.047
C23
0.1
C
9.0V
IN6F R1-B
REG2SW
R1OUT
REG1SW
VM3
3
IN5F
2
31 30
IN5R
1
33 32
R39
1M
0V
D4
HZU 3.6B1
D3 HZU 3.3B1
C
TRK-
C12 1
C
C53
0.1
35 34
O6-
R51
680
D1
HZU 3.0B1
36
C81
10p
CLCK
C
C83
1
C
8
O6+
7
O5-
6
O5+
5
IC4
BD7961FM
C9
1
C85
1
R28
3.3 1/4W
LO+
LOC40
0.1
VREF
IC9
BD7931FE2
C
C
R13
470
C7
0.01
C5
47 10V TAN
1
X1
16.92M
C
R33 680
0V
1
TEST3
2
MO-
2
3
R31
680
REQ
N.C.
4
MOT3
UP/DOWN
(V-MOTOR)
DRMUT
3
C59
0.1
SDA
4
3.3V
1.6V
SCL
L-CH
D-GND
C
R2 220
R77 0
5
GND
C4 1
0V
SDA
6
3.3V
REQ
R-CH
TP25
RESET
C14
47 10V TAN
C
Q7
DTC114EUA
12.0V
11
RESET 10
VDD 9
Q6
2SB1188
R12
22K
3.0V
SPDIF 12
7
TP14
VDD
CD3.3
C13 1
C
PGND BIAS
3.3V
SDA 13
8
R3
220
0V
VDD
Q8
2SB1427 3.3V
C
3.3V
A-MUTE 14
P-GND
3.3V
3.3V
SCL 15
P-GND
C3
0.1
3.3V
REQ 17
SYS-ACC 16
C
CD-9V 18
C1
47
25V
TAN
9.0V
CD-9V 19
B/U
R29
6.8
1/2W
Q20
2SB1427
J1
074-1237-69
PRINTED WIRING BOARD
CD PWB(BM1) section
Sensor-L-FPC(BM2) section
Sensor-U-FPC(BM3) section
Drive Unit
B
BLK
RED
(-)
(+)
MOT3
Up/Dw
To Main PWB
CD PWB(BM1) section
A
CD PWB(BM1) section
SOLDER SIDE
COMPONENT SIDE
PT2
PT1
A
MOT1
Loading
Sensor-L-FPC(BM2) section
(+)
PT3
(-)
B
MOT2
Mode
Sensor-U-FPC(BM3) section
LED1
(-)
BLK
(+)
S5
Shutter
RED
LED3
LED2
- M16 -
929-0371-80
Caution:
COMPONENT SIDE: Parts on the
component side seen from the
component side are indicated.
SOLDER SIDE: Parts on the solder
side seen from the solder side are
indicated.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages