Operating the Radio

Operating the Radio
EN
EN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
D O N OT R E M OV E C OV E R
( O R BAC K ) . N O U S E R S E RV I C E A B L E PA RT S I N S I D E . R E F E R S E RV I C I N G
T O Q UA L I F I E D S E RV I C E
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R TA N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING: TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
FCC Information
FCC Information
For Your Safety
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson
Inc. could void the user’s authority to operate this
product.
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:
• Re-orient the receiving antenna (that is, the
antenna for the radio or television that is
“receiving” the interference).
• Move the unit away from the equipment that is
receiving interference.
• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference
are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problems.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
The AC power plug is polarized
(one blade is wider than the
other) and only fits into AC
power outlets one way. If the
plug will not go into the outlet
completely, turn the plug over
and try to insert it the other
way. If it still does not fit, contact a qualified
electrician to change the outlet, or use a different
one. Do not attempt to bypass this safety feature.
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY WITH
SAME TYPE FUSE.
Service Information
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
Technical Specification
Product: Clock Radio with CD player
Brand: RCA
Model: RP4010
Electrical Consumption
Power Supply: 120V~60Hz
Power Consumption: 40 Watts
IMPORTER
Comercializadora Thomson de México, S.A. de
C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
For Your Records
In the event that service should be required, you
may need both the model number and the serial
number. In the space below, record the date and
place of purchase:
Date of Purchase:
Place of Purchase:
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.
1
EN
Battery Back-Up Operation
EN
This clock radio is equipped with a memory
holding system that can be powered with
2 “AAA” batteries (not included). The
power failure protection circuit will not
operate unless battery is installed.
When normal household power is
interrupted, or the AC line cord is
unplugged, the battery will power the
clock radio to keep track of time and alarm
settings programmed into memory. When
the battery backup functions, the digital
display will not light, however, the
function of alarm still occurs during the
power interruption if the remaining
battery power is adequate. Normal
operation will resume after AC power is
restored so you will not have to reset the
time or the alarm.
2
Install battery as follow:
1. Unlock the battery compartment door
(located at the bottom of the radio) by
sliding the tab away from the door.
2. Remove the battery compartment door.
3. Insert 2 “AAA” batteries.
4. Replace the compartment door and
slide the tab to lock battery
compartment.
Power Failure Indicator
When AC power is interrupted
(disconnected) for a short period of time,
both time and alarm settings will change
(unless optional battery is installed). After
AC power is restored (reconnected), the
Digital Display will blink to indicate that
power was interrupted and you should
readjust the time and alarm settings.
General Controls
EN
WAKE UP Station / Track - sets the wake up
radio station or CD track.
CD MODE - selects repeat / repeat all / shuffle /
repeat shuffle in CD mode.
Rev - skips / searches backward.
Play / pause - starts / pauses CD playback.
Fwd - skips / searches forward.
Stop - stops CD playback.
Open / close - opens / closes the CD
compartment.
NAP - sets the alarm to sound after a specific
period of time. (Alarm tone only)
WEEKEND CANCEL - activates Weekend
Cancel function.
SLEEP - activates SLEEP function.
WAKE 1 - activates WAKE 1 setting, press
MEMO RECALL - recalls available preset radio
stations.
<< / >> - changes time / radio frequency / CD
track
SET - sets clock / wake time; store preset
memory in radio mode.
VOLUME CONTROL - rotates to adjust volume
RADIO ON/BAND- turns on the radio / changes
radio band
OFF - turns off the radio / alarm / CD
v
v
repeatedly to cycle wake mode:
WAKE 2 - activates WAKE 2 setting, press
v
v
v
repeatedly to cycle wake mode:
CANCEL - cancels WAKE setting.
SNOOZE - turns off the alarm momentarily.
3
v
Remote Control
EN
RADIO ON / BAND- turns on the radio / changes radio band
MEMO RECALL - recalls available preset radio stations.
OFF - turns off the CD / radio / alarm tone
MUTE - mutes the volume.
VOLUME - / + - adjusts the volume.
Play / pause - starts / pauses CD playback.
Stop - stops CD playback.
TRACK / TUNE I<< / >>I - changes time / radio frequency / CD track
SNOOZE - turns off the alarm momentarily.
SLEEP - activates the SLEEP function.
4
Display
EN
Clock Display
TRACK
- No disc detected.
- In clock setting mode.
- In radio mode, displays memory
WEEKEND CANCEL - Weekend Cancel is
activated. Wake settings are activated
during Mon to Fri, but are cancelled on
Sat and Sun.
- Nap activated.
- Sleep activated.
AM - In AM radio band.
FM - In FM radio band.
recall number.
- Displays when the alarm radio
station is set.
MHz / kHz - Radio frequency unit.
MON TUE WED THU FRI SAT SUN Day indicator
CD - In CD mode.
- Volume level (min. 00 - max.
VOLUME
- repeats the current track.
79)
- repeats the whole disc.
- plays tracks randomly.
- plays random track repeatedly.
TRACK
- In CD mode, displays track
number.
Wake 1 and Wake 2 Display
/
/
/
- Wake 1 source.
/
- Wake 2 source.
- Wake to CD.
- Wake to alarm tone.
- Wake to radio.
AM - AM time indicator.
PM - PM time indicator.
- Wake time.
5
Setting the Clock
EN
Setting Clock Time
Setting the Day
Your digital clock operates on a 12-hour
standard mechanism. AM or PM will show
on the display accordingly.
1. Press SET repeatedly until the day
indicator flashes on the display.
2. Press << or >> to set the day.
When you first turn on the unit:
shows on the display
1. The clock icon
2. Press << or >> to set the clock time.
When you press and hold << or >>, the
time decrements or increments will follow by a faster rate.
Or you can adjust the clock anytime by
following below procedures:
1. Press SET repeatedly until the clock icon
shows on the display.
2. Press << or >> to set the clock time.
When you press and hold << or >>, the
time decrements or increments will follow by a faster rate.
6
Operating the Radio
EN
Antennas
Tuning the Stations
FM antenna - The power cord acts as your
FM antenna. It picks up moderate to
strong radio stations and eliminates the
need for an external antenna in most
strong signal areas. Be sure the power cord
is stretched to its full length. Do not coil
or bunch the cord together. Changing
position of the power cord may improve
reception.
1. Plug the power cord into any 120V AC
household outlet.
2. Press RADIO ON/BAND (located on the
top of the radio) to turn on the radio.
3. Press RADIO ON/BAND to select the
desired broadcast band.
4. Press << or >> to tune to your desired
radio station.
5. Press OFF to turn off the radio.
AM Antenna - A built-in ferrite rod
antenna eliminates the need for an
outside antenna for AM reception.
Rotating the unit slightly may improve
reception of distant AM stations.
7
Operating the Radio
EN Setting the Preset Radio
Stations
1. Press RADIO ON/BAND to turn on the
radio.
2. Press RADIO ON/BAND to change the
broadcast band.
3. Press << or >> to tune to your desired
radio station.
4. If you want to memorize this radio station, press SET once, and then press
MEMO RECALL repeatedly to choose
the radio station number you want to
record in.
5. Press SET again to confirm.
6. If you set the radio station in the AL
location, it will be the wake up radio
station of the alarm.
Note:
This unit can store up to 11
preset radio stations, while
AL location is for the wake
up radio station.
Automatic Radio Station
Search
1. Press RADIO ON/BAND (located on the
top of the radio) to turn on the radio.
2. Press and hold << or >> for 2 seconds, it
will automatically search a radio station
for you.
Selecting the Preset Radio
Stations
1. Press RADIO ON/BAND to turn on the
radio.
2. Press MEMO RECALL repeatedly to select your desired preset radio station.
Overwriting the Preset Radio
Stations
1. First, press << or >> to tune your desired preset radio station.
2. Press SET once and then press MEMO
RECALL repeatedly to choose the radio station number you want to overwrite.
3. Press SET again to confirm.
Deleting the Preset Radio
Stations
1. Press MEMO RECALL repeatedly to select your preset radio station you want
to delete.
2. Press and hold SET for 3 seconds to delete the selected preset radio station.
8
Operating the Alarm
Note:
You cannot set wake time
in radio mode.
The unit equips with GRADU-WAKE feature, the alarm
tone volume will increase gradually to
its maximum in about 30 to 45 seconds.
Attention:
When the AC power is disconnected, the unit will enter DC backup mode, all
wake mode will be reverted
to alarm tone.
Selecting Wake Mode
EN
wake options.
v
To change to another wake mode (e.g.
from CD to radio), simply press WAKE 1
or WAKE 2 repeatedly to scroll through
v
1. Press SET repeatedly until WAKE 1
or WAKE 2 / / icon
/ /
flashes on the display.
2. Press << or >> to set the wake time.
The time decrements or increments will
follow by a faster rate when you press
and hold either << or >>.
3. Press SET repeatedly to exit setting
wake time mode.
v
Setting the Wake Time
Waking to Alarm Tone
When waking to alarm tone is selected,
icon is displayed.
the
The unit is equipped with GRAD-UWAKE feature, the alarm tone volume
will increase gradually to its maximum
in about 30 to 45 seconds.
Tip:
If you set the SLEEP
function with low volume
level before going to bed,
we advise using Waking to Alarm
Tone mode to wake you up since the
volume will automatically increase.
9
Operating the Alarm
EN
Waking to RADIO
When the waking to radio is selected, the
icon is displayed.
1. Set the wake time (see directions on
the previous page).
2. Press WAKE 1 or WAKE 2 to select waking up by RADIO .
3. Rotate VOLUME CONTROL to your
desired wake up volume.
4. Press OFF to turn off the radio.
You can select your wake up radio station
by the following procedures.
1. Press RADIO ON/BAND to turn on the
radio.
2. Press << or >> to tune to your desired
radio station.
3. Press and hold WAKE UP Station /
Track to store the current radio station
as the wake up radio station.
will
show on the display.
Note:
“AL” refers to the Alarm
Station. If no WAKE
STATION is set, the wake
up radio station will stay at your last
listening radio station.
Waking to CD
2. Press WAKE 1 or WAKE 2 to select waking up by CD .
3. Rotate VOLUME CONTROL to your
desired wake up volume.
4. Press OFF to turn off the radio.
You can select your CD wake up track by
the following procedures.
1. In CD mode, while pressing WAKE UP
Station / Track, press << or >> to select your desired CD wake up track.
Turning off Alarm
Silence the alarm momentarily
Press SNOOZE. The alarm will sound again
when the snooze period is over. (see
“Snooze” on page 13).
Stop the alarm
Press OFF. Then, the alarm will be on the
following day at the same time.
Disable the alarm permanently
1. Press CANCEL.
2. The WAKE 1 / / or WAKE 2
/ / icon will flash, while it is flashing, press WAKE 1 or WAKE 2 to cancel the alarm. Corresponding WAKE indicator will disappear.
3. To activate the alarm again, press
WAKE 1 or WAKE 2 , and the WAKE
indicator will appear.
When the waking to CD is selected, the
icon is displayed.
Note:
1. Set wake time (see directions on the
previous page).
You can activate the
previous wake settings by
pressing WAKE 1 or WAKE
2.
10
Operating the CD Player
EN
Listening to Compact Disc
Selecting Play Mode
1. Press OPEN to open the CD compartment.
2. Insert a disc, the compartment will automatically close.
3. Press Play/pause.
4. Adjust volume to your desired level.
5. Press Rev or Fwd to skip backward or
forward the CD track.
6. Press and hold Rev or Fwd to search
forward or backward the CD track.
7. Press STOP to stop CD playback.
1. Start CD playback.
2. During playback, press CD MODE to
toggle between different play modes.
Note:
“nd” will show on the display
when no disc is detected. (e.g.
scratched CD or mp3 disc is
inserted)
Attention:
The unit only supports
5 inch CD.
- repeats the current track.
- repeats the whole disc.
- plays tracks randomly.
- plays random track repeatedly.
!
Warning:
Do not press on the CD compartment when it is opened.
Note:
When there is no disc in the
CD compartment, the pre-installed music tracks will be
played.
11
Alarm Settings
EN
Setting Sleep Time
Sleep to CD
In sleep mode, the radio and CD will turn
off automatically. To set the sleep time,
simply:
1. Press SLEEP, then the time display will
exhibit 0:59.
2. While holding SLEEP, press << or >> to
set the sleep time. The time range is
from 1 minute to 2 hours.
3. Release SLEEP and the current time will
be shown again.
Press Play/pause after setting the sleep
time to begin CD playback. The unit will
turn off automatically once the sleep
time is reached.
Viewing Remaining Time
Press SLEEP to read the remaining
sleep time.
Tip:
Sleep to Radio
Turn on the radio after setting the sleep
time, you may select the radio station as
usual. Once the sleep time is reached,
the radio will turn off automatically.
Sleep radio station will automatically
switch to the last sleep radio station
setting. You must reset to sleep to a
different radio station.
1. Press RADIO ON/BAND.
2. Press << or >> to tune to the radio station you want to sleep to.
12
If you decide to turn off the
unit sooner, press SNOOZE or
OFF.
Tip:
When SLEEP is activated
again, the sleep time will be
the same as the one you
have set before.
Alarm Settings
Nap Mode
For catnaps up to 2 hours without disturbing the regular alarm settings, the NAP
function wakes you up after a short period of time. Simply:
1. Press NAP, the NAP indicator will flash.
While the NAP indicator is flashing,
press << or >> to adjust nap time. The
time range is from 10 minutes to 2 hours
at 10 minutes interval.
2. Press NAP again to confirm, the NAP
indicator will show on the display.
3. Press NAP once to show time left.
Stopping the Nap Alarm
When the NAP alarm sounds, you can
press OFF to stop it.
Snooze
This operation allows extra sleep time after
the alarm is on. The alarm will be off by
pressing SNOOZE until the snooze period
is over. Snooze function can be used
repeatedly up to 2 hours. After this, the
alarm will turn off until the next alarm
conditions are met. Set the “quiet” period
as follows:
1. While pressing SNOOZE, press << or >>
to set the “quiet” period (the default
time is 9 minutes) from 1 minute to 30
minutes. Release button, then the
“quiet” period is set.
Weekend Cancel
Tip:
Wake settings are activated during Mon
to Fri, but are cancelled on Sat and Sun.
(Work only when wake setting is active)
1. Press and hold WEEKEND CANCEL for
5 seconds.
2. The WEEKEND CANCEL icon will appear on the display.
3. Press and hold WEEKEND CANCEL for
5 seconds to disable the Weekend Cancel function.
Only alarm tone can be selected in NAP mode.
Adjusting the Dimmer
Cancelling the Nap Alarm
Press and hold NAP for 5 seconds to
cancel the nap setting.
Press << or >> to adjust dimmer level.
Default is the brightest.
Note:
You cannot adjust the dimmer
in CD and radio mode.
13
EN
U.S. Limited Warranty
EN
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year from date of purchase.
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the
rental firm, whichever comes first.
What we will do:
• Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for
the remainder of the original product’s warranty period.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
is within the warranty period must be presented to obtain warranty service. For rental firms, proof of
first rental is also required.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.
• Include evidence of purchase date such as the bill of sale. Also print your name and address and a
description of the defect. Send via standard UPS or its equivalent to:
Thomson Inc.
Product Exchange Center
11721 B Alameda Avenue
Socorro, Texas 79927
• Insure your shipment for of loss or damage. Thomson accepts no liability in case of damage or loss en
route to Thomson.
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating Instructions
and user controls. For additional information, ask your dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
14
U.S. Limited Warranty
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply
to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state
to state.
If you purchased your product outside the USA:
This warranty does not apply. Contact your dealer for warranty information.
15
EN
Canadian Limited Warranty
EN
Thomson multimedia Ltd. warrants to the purchaser or gift recipient that if any manufacturing defect
becomes apparent in this product within 1 year from the original date of purchase, it will be replaced
free of charge, including return transportation.
This warranty does not include damage to the product resulting from accidents, misuse or leaking
batteries.
Should your product not perform properly during the warranty period, either:
1. Return it to the selling dealer with proof of purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack product complete with accessories in the original
carton (or equivalent). Mail prepaid (with proof of purchase) and insured to:
Thomson multimedia Ltd.
6200 Edwards Blvd.,
Mississauga, Ontario, L5T 2V7
Canada
The provisions of this written warranty are in addition to and not a modification of or subtraction from
the statutory warranties and other rights and remedies contained in any applicable legislation, and to
the extent that any such provisions purport to disclaim, exclude or limit any such statutory warranties
and other rights and remedies, such provisions shall be deemed to be amended to the extent necessary
to comply therewith.
If you are unable to find a qualified servicer for out of warranty service, you may write to:
Thomson Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This information is required if service is
needed during the warranty period.
PURCHASE DATE
NAME OF STORE
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement