Fisher | VPC-T850 | User's Manual | Fisher VPC-T850 User's Manual

Fisher VPC-T850 User's Manual
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of
the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.
EN-1
READ THIS FIRST
Trademark Information
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Pentium® is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Inc.
SD™ is a trademark.
SDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
The product and accessories that come with your camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and internal
memory capacity. Contact your dealer for precise product definition and included
accessories.
The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your camera.
The manufacturer assumes no liability for any errors or discrepancies in this user
manual.
EN-2
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power
off and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
EN-3
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to
leak. If the internal fluid enters your eyes or comes into contact with your
body or clothes, rinse with fresh water. If the internal fluid has entered your
eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and
electric shock.
EN-4
Warning:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
FOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of California
(USA):
WARNING:
This product contains chemicals, including lead, known to the States of California to
cause cancer, birth defects or other reproductive harm. Wash hands after handling.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designated to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the userís authority to operate the equipment.
EN-5
FOR CANADIAN USERS
This Class B digital apparatus complies with Canadian ICES-003
FOR EU USERS
Note:
This symbol mark and recycle system apply to EU countries and
do not apply to countries in other areas of the world.
Your SANYO product is designed and manufactured with high
quality materials and components which can be recycled and
reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household
waste.
Please dispose of the equipment at your local community waste
collection/recycling centre.
In the European Union there are separate collection systems for
used electrical and electronic products.
Please help up to conserve the environment we live in!
Manufacturer and Address
SANYO Electric Co., Ltd.
5-5, Keihan-hondori, 2-chome,
Moriguchi City, Osaka, Japan
Authorized Representative and Address
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 Munich, Germany
EN-6
Symbols used in this manual
Points giving some extended instructions or special points to pay attention to.
You many find the answers to questions or problems concerning camera operation in
the sections “Troubleshooting”.
FCC information
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Declaration of Conformity
Model number: VPC-T850
Trade Name: SANYO
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street
Chatsworth, California 91311
Telephone No.: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Canadian ICES-003 information
This class B digital apparatus complies with Canadian ICES-003.
EN-7
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions
and the notes described below:
Use only the specified battery (3.7V).
Avoid extremely cold environments as low temperatures can shorten the battery life
and reduce camera performance.
When you are using a new rechargeable battery or a rechargeable battery that has
not been used for an extended period of time, it may affect the number of images
that can be captured. Therefore, to maximize its performance and lifetime, we
recommend that you fully charge the battery and discharge it for at least one
complete cycle before use.
The battery may feel warm after a long period of continuous use of the camera or the
flash. This is normal and not a malfunction.
The camera may feel warm after a long period of continuous use. This is normal and
not a malfunction.
If the battery is not to be used for a long period of time, remove it from the camera to
prevent leakage or corrosion and store it after no battery power is left. Stored for a
long time in a fully charged condition, its performance may be impaired.
Always keep the battery terminals clean.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used battery according to the recycle instructions.
Charge the rechargeable battery fully before using for the first time.
To prevent short-circuiting or fire, keep the battery away from other metal objects
when carrying or storing.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
EN-8
CONTENTS
10 INTRODUCTION
28 MENU OPTIONS
10 Overview
10 Package Contents
28
31
32
33
11 GETTING TO KNOW YOUR
CAMERA
Capture Menu
Video Menu
Playback Menu
Setup Menu
11 Front View
12 Rear View
13 LCD Monitor Display
34 TRANSFERRING FILES TO
YOUR COMPUTER
15 GETTING START
35 USING THE CAMERA AS A PC
CAMERA
15 Preparation
16 Charging the Battery
17 Initial Settings
19 CAPTURE MODE
19 Capturing Images
20 Recording Shots using Face
Detection Technology
21 Recording Voice Memos
22 VIDEO MODE
22 Recording Video Clips
22 Playing Back Video Clips
34 Downloading Your Files
36 EDITING SOFTWARE
INSTALLATION
37 SPECIFICATIONS
38 APPENDIX
38 Possible Number of Shots
39 Troubleshooting
40 Connecting to a PictBridge Compliant
Printer
23 PLAYBACK MODE
23
24
24
25
26
27
Playing Back Still Images
Thumbnail Display
Removing Red-eye
Attaching Voice Memos
Protecting Images
Erasing Images
EN-9
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 8.1-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 3264 x 2448 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
„ Digital Camera
„ Software CD-ROM
„ USB cable
„ AV cable
„ Camera strap
„ Camera pouch
„ Rechargeable lithium-ion battery
„ Battery charger
„ AC adapter for battery charger
„ Instruction manual
Optional Accessory:
„ SD/SDHC memory card
„ Accessories and components may vary by retailer.
EN-10
GETTING TO KNOW YOUR CAMERA
Front View
1. Shutter button
2. Flash
3.
Power button
4. Status LED
5. Microphone
6. Lens
7. Self-timer LED
8. Zoom lever
EN-11
Rear View
1. LCD monitor
2.
Mode button
3.
Menu button
4. Direction button
S
X
T
W
EN-12
button
Focus button
button
Flash button
button
Self-timer button
Delete button
button
Backlight / Exposure
compensation button
5. Strap holder
6. USB or AV OUT terminal
7.
Set button
Display button
8.
Playback button
9. Battery / Memory card cover
10. Tripod socket
11. Speaker
LCD Monitor Display
Capture mode
1. Zoom status
2. Voice memo
3. Battery condition
[
] Full battery power
[
] Medium battery power
[
] Low battery power
[
] No battery power
4. Flash mode
[Blank]Auto Flash
[
] Red-eye Reduction
[
] Pre-flash
[
] Forced Flash
[
] Flash Off
5. Storage media
[
] Internal memory (no card)
[
] SD/SDHC memory card
6. [
] Histogram
7. Main focus area (When the shutter
button is pressed halfway)
8. Image quality
[
] Fine
[
] Standard
[
] Economy
9. Image size resolution
[
] 3264 x 2448
[
] 2816 x 2112
[
] 2272 x 1704
[
] 1600 x 1200
[
] 640 x 480
10. Available number of shots
11. ISO
[Blank] Auto
[
] ISO 64
[
] ISO 100
[
] ISO 200
[
] ISO 400
[
] ISO 800
[
] ISO 1600
12. Self-timer icon
[
]
2 sec.
[
]
10 sec.
[
] 10+2 sec.
13. Date and time
14. [
] Exposure compensation
[
] Backlight correction
(Adjust exposure value with the e / f buttons)
15. Capture mode icon
[Blank] Single
[
]
Continuous
[
]
Auto Exposure Bracketing
1
19
18
17
P
m
2
x4.0
3
q
6
16
7
15
14
4
5
f
+ 0.3
2008 / 03 / 01 00 : 00
13
8
9
00001
12
11 10
[
]
Burst
[
]
Series+flash
[
]
Pre-Shot
[
]
Couple Shot
16. Slow shutter warning
17. White balance
[Blank] Auto
[
] Incandescent
[
] Fluorescent 1
[
] Fluorescent 2
[
] Daylight
[
] Cloudy
[
] Manual
18. Focus setting
[Blank] Auto focus
[
] Face detection
[
] Macro
[
] Infinity
19. Scene mode
[ P ] Program AE
[
] Anti Shake
[
] Panorama
[
] Portrait Man
[
] Portrait Lady
[
] Landscape
[
] Sports
[
] Night Portrait
[
] Night Scene
[
] Candlelight
[
] Fireworks
[
] Text
[
] Sunset
[
] Sunrise
[
] Splash Water
[
] Flow Water
[
] Snow
[
] Beach
[
] Pets
[
] User Setting
EN-13
Video mode [
]
1. Zoom status
2. Flash mode
3. Battery condition
4. Storage media
5. Main focus area
6. Video quality
7. Video resolution
8. Available recording time/Elapsed time
9. Self-timer icon
10. Date and time
11. Focus setting
12. Mode icon
Playback mode [
1.
2.
3.
4.
5.
EN-14
x4.0
11
4
5
6
7
00 : 21
2008 / 03 / 01 00 : 00
10
9
8
1
2
14
x a Shutter:Play
A
13
1 / 38
12
F2.8
15
3
4
11
5
f
+ 0.3
01 / 01 / 2008 00:00
E 100- 0001
9
10
] - Video playback
Video status bar
Elapsed time
File number
Folder number
Sound off icon (When the c button is
pressed during video playback)
6. Play mode
7. Mode icon
8. Total recorded time
2 3
12
] - Still image playback
1. Voice memo
2. Battery condition
3. Storage media
4. Histogram
5. ISO
6. Image quality
7. Image size resolution
8. File number
9. Folder number
10. Date and time
11. Exposure value
12. Aperture value
13. Shutter speed value
14. Protect icon
15. Mode icon
Playback mode [
1
6
7
8
1
8
Total
00 : 00 : 08
Rq
7
6
5
Play
00 : 00 : 01
E 100 - 0001
4
3
2
GETTING START
Preparation
1. Attach the camera strap.
2. Open the battery/memory card cover.
3. Insert the supplied battery with correct orientation as
shown.
4. Insert an SD/SDHC memory card (Optional).
„ The camera has 32MB internal memory (28MB
available for image storage), but you can load an
SD/SDHC memory card to expand the camera’s
memory capacity.
„ Be sure to format the memory card with this
camera before its initial usage.
5. Close the battery/memory card cover and make sure it
is locked securely.
„ To prevent valuable data from being accidentally erased from
an SD/SDHC memory card, you can slide the write protect tab
(on the side of the SD/SDHC memory card) to “LOCK”.
„ To save, edit, or erase data on an SD/SDHC memory card,
you must unlock the card.
„ To prevent damaging of an SD/SDHC memory card, be sure
to turn off the power when inserting or removing the SD/
SDHC memory card. If inserting or removing the SD/SDHC
memory card with the power on, the camera will automatically turn off.
EN-15
Charging the Battery
Charge the battery fully with the supplied battery charger before use.
1. Insert the battery into the battery charger.
2. Connect the power cord to the charger and
insert the plug into a wall outlet.
„ The status LED on the charger lights red
when charging has started and lights
2
green when charging is completed. The
LED also lights green if no battery is
inserted into the charger.
„ Charging time varies according to the
ambient temperature and the status of battery.
„ Remove the battery after charging is completed.
1
„ The battery may feel warm after it has been charged or immediately after being used. This is
normal and not a malfunction.
„ When using the camera in cold areas, keep the camera and battery warm by holding them inside
your outer clothes.
EN-16
Initial Settings
Setting the Date and Time
The date/time needs to be set if and when:
„ The camera is turned on for the first time.
„ The camera is turned on after leaving the camera without the battery for an
extended period of time.
When the date and time information is not displayed on the LCD monitor, follow these
steps to set the correct date and time.
1.
2.
3.
4.
Press the
button to [ ] or [ ].
Press the
button.
Select [Setup] with the f button.
Select [Date/Time] with the c / d buttons, and
press the
button.
5. Select the date format with the c / d buttons,
and press the
button.
„ Select the item’s field with the e / f buttons
and adjust the value for the date and time
with the c / d buttons.
„ The time is displayed in 24-hour format.
„ After confirming all settings are correct, press
the
button.
6. To exit from the [Setup] menu, press the
button.
EN-17
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD monitor.
1.
2.
3.
4.
Press the
button to [ ] or [ ]; or press the [
Press the
button.
Select [Setup] menu with the f button.
Select [Language] with the c / d buttons and press
the
button.
5. Select the displayed language with the c / d
buttons and press the
button.
„ The setting will be stored.
] button.
Formatting the Memory Card or Internal Memory
This utility formats the internal memory (or memory card) and erases all stored images
and data.
1.
2.
3.
4.
Press the [ ] button.
Press the
button.
Select [Setup] menu with f button.
Select [Format] with the c / d buttons, then
press the
button.
5. Select [Execute] with the c / d buttons, and
press the
button.
„ To cancel formatting, select [Cancel] and
press the
button.
EN-18
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.8" full color TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the
button to turn the power on.
„ The status LED lights green and the camera is initiated.
„ If the power is turned on in [ ] or [ ] mode, the lens will extend forward and it
is ready for shooting. In both modes, if the camera mode is changed to [ ], the
lens barrel will retract into the camera body after 30 seconds.
2. Press the
button to [ ].
3. Compose your image in the LCD monitor.
„ Slide the zoom lever to
side to zoom in on the subject, and enlarges the
subject on the LCD monitor.
„ Slide the zoom lever to
side to zoom out on the subject, and provides a wider
angle image.
4. Press the shutter button.
a
„ Pressing the shutter button down halfway
b
automatically focuses and adjusts the
exposure, and pressing the shutter button
down fully captures the images.
„ The focus area frame turns green when
the camera is in focus and the exposure is
calculated.
„ When the focus or exposure is not
suitable, the frame of the focus area turns
red.
EN-19
Recording Shots using Face Detection Technology
Face Detection Technology can identify and focus on the human faces in the image.
This advanced function simultaneously detects up to 5 human faces regardless of their
position in the scene.
White frame
Face detection function is on
Green frame
Focus lock
Out of focus
1. Press the
button to [ ].
2. Press the
button until [ ] icon appears on the LCD monitor.
„ The white frame is identified as the “top priority” face (main focus frame), and
gray ones around the other faces.
3. Press the shutter button halfway down to lock the focus.
„ The main focus frame simultaneously turns green.
„ If the “top priority” face is out of focus, all frames will be disappeared from the
screen.
4. Press the shutter button down fully to capture your image.
„ Subjects that are not suitable with this function:
a. A person is wearing glasses, sunglasses, or face is covered with hat or hair.
b. A person turned sideways.
EN-20
Recording Voice Memos
A voice memo can be recorded once for 30 seconds in the still image mode immediately
following a still image capture.
1.
2.
3.
4.
5.
Press the
button to [ ].
Press the
button, and select the [Function] menu with the f button.
Select [Voice Memo] with the c / d buttons, and press the
button.
Select [On] with the c / d buttons, and press the
button.
Press the
button to exit from the menu.
„ An [ ] icon is displayed on the screen.
6. Compose the image, press the shutter button down halfway, then press it down fully.
„ [VOICE RECORDING] is displayed on the screen immediately, and the voice
memo recording starts.
7. Press the shutter button one more time during recording, or wait for 30 seconds.
„ [VOICE RECORD END] will be displayed and the recording will end.
„ An [ ] icon is displayed with images that have been recorded with a voice
memo.
EN-21
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 pixels.
button to [ ].
1. Press the
2. Compose the image.
3. Press the shutter button.
„ The recording of the video clip will start.
„ Pressing the shutter button one more time will end
the recording of the video clip.
„ The recording time depends on the storage size
and the subject of the image to be recorded.
„ The zoom function cannot be used during video
recording.
f
„ When recording a video clip, the flash and "10+2 sec." self-timer function cannot be used.
„ If the write speed of your SD/SDHC memory card is not fast enough for recording video clips in
the currently selected quality, the video recording will stop. In this case, select a video quality
lower than the current one.
Playing Back Video Clips
You can play back recorded video clips on the camera. You can also play back sound if
recorded with the video.
1. Press the [ ] button.
„ The last image appears on the screen.
2. Select the desired video clip with the e / f buttons.
button.
3. Press the
„ A press of the f / e buttons during playback allows fast forward play / fast reverse play.
„ To stop video playback, press the d button.
This stops playback and returns to the start of the video clip.
„ To pause video playback, press the
button.
This pauses video playback.
button again.
To cancel pause, press the
„ Video clips cannot be displayed rotated or enlarged.
„ Windows Media player or QuickTime Player is recommended to play back the video clip on your
computer.
„ QuickTime Player is a free media player available at www.apple.com; and compatible with Mac
and Windows computers.
„ For more information about the operation of the media player, refer to its respective help documentation.
EN-22
PLAYBACK MODE
Playing Back Still Images
You can play back the still images on the LCD monitor.
1. Press the [ ] button.
„ The last image appears on the screen.
2. The images can be displayed in forward or
reverse sequence with the e / f buttons.
„ To view the previous image, press the e
button.
„ To view the next image, press the f button.
„ Pressing the c button during image playback will
result in a 90-degree clockwise rotation display.
„ Slide the zoom lever to
side enlarges the
image.
„ To return to normal magnification, slide the
zoom lever to
side.
„ An [ ] icon is displayed with the video data. Video clips cannot be rotated.
„ An [ ] icon is displayed with images which have an audio memo recorded.
EN-23
Thumbnail Display
This function allows you to view 9 thumbnail images on the LCD monitor at the same
time, which can let you quickly search for the image that you want.
1. Press the [ ] button.
„ The last image appears on the screen.
2. Slide the zoom lever to
side.
„ The images are displayed in the thumbnail
display.
3. Press the c / d / e / f buttons to select the
image to be displayed at regular size.
4. Press the
button.
„ The selected image is displayed at its
regular size.
„ An [
], [
], [
6
E 100- 0005
] icon may be displayed in a thumbnail.
Removing Red-eye
You can use this function to remove the red-eye effect after an image is taken.
1. Press the [ ] button.
2. Select the image that you want to edit with the
e / f buttons.
3. Press the
button.
4. Select [Fix Red Eyes] with the c / d buttons,
and press the
button.
5. Select [Execute] with the c / d buttons, and
press the
button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm]
with the c / d buttons, and press the
button.
„ When this process ends, this replaces the
original image with the corrected image.
EN-24
Attaching Voice Memos
A maximum of 30 seconds of audio can be recorded as a memo for captured still
images. The voice memo can be recorded only once.
1. Press the [ ] button.
„ The last image appears on the screen.
2. Select the image to which you want to attach the voice memo with the e / f
buttons.
3. Press the
button.
4. Select [Voice Memo] with the c / d buttons, and press the
button.
5. Select [On] with the c / d buttons, and press the
button.
6. Press the
button to exit from the menu.
7. Press the shutter button.
„ [VOICE RECORDING] is displayed on the screen and recording starts.
8. To stop recording a voice memo as it is being recorded, press the shutter button
again.
„ [VOICE RECORD END] will be displayed and the recording will end. An [ ] icon
is displayed with images that have been recorded with a voice memo.
Playing back voice memo
A press of the shutter button displays [VOICE
PLAYBACK] and plays back the voice memo.
x a Shutter:Play
E 100- 0001
„ Voice memo is only available for still images.
EN-25
Protecting Images
Set the data to read-only to prevent images from being erased by mistake.
1. Press the [ ] button.
2. Select the image that you want to protect with the e / f buttons.
3. Press the
button.
4. Select [Protect] with the c / d buttons, and press the
button.
5. Select [Single] or [All] with the c / d buttons, and press
button.
the
6. Select [Set] with the c / d buttons, and press the
button.
„ Protection is applied to the image and the camera
returns to the playback mode.
„ The protect icon [ ] is displayed with protected images.
When [All] has been selected, [ ] is displayed
with all the images.
Canceling the Protection
To cancel protection for only one image, display the image on which
you want to remove the image protection.
1. Select [Protect] with the c / d buttons from the playback
menu, and press the
button.
2. Select [Single] or [All] with the c / d buttons, and press
button.
the
3. Select [Cancel Protect] with the c / d buttons, and press
button.
the
„ The removal of image protection is executed and the camera
returns to the playback mode.
Protecting multiple images simultaneously
1. Select [Protect] with the c / d buttons from the playback menu, and press the
button.
2. Select [Select] with the c / d buttons, and press the
button.
„ The images are displayed in the thumbnail display.
3. Select the image you want to protect with the e / f buttons, and press the d button.
„ The protect icon [ ] is displayed with protected images. One more press of the d
button will cancel the operation. This procedure is repeated to select multiple images.
button.
4. Press the
button.
5. Select [Execute] with the c / d buttons, and press the
„ Protection is executed and the camera returns to playback mode.
„ Formatting an SD/SDHC memory card overrides protection, and erases all images regardless of
their protected status.
EN-26
Erasing Images
Erasing single image / Erasing all images
1. Press the [ ] button.
2. Select the image you want to erase with the e /
f buttons.
3. Press the
button.
4. Select [Single] or [All] with the c / d buttons,
and press the
button.
„ [Single]: Erases the selected image or the
last image.
„ [All]: Erases all of the images except for the
protected images.
„ [Select]: Erases a number of selected images.
5. Select [Execute] with the c / d buttons, and
press the
button.
„ To not erase, select [Cancel], and press the
button.
Erasing selected images
This erases a number of selected images.
1. Press the [
] button.
2. Press the
button.
3. Select [Select] with the c / d buttons, and
press the
button.
„ The images are displayed in the thumbnail
display.
4. Select the image you want to erase with the e /
f buttons, and press the d button.
„ The [
] icon will be displayed. One more
press of the d button will cancel the
operation. Repeat this procedure and select
all the images that you want to erase.
5. Press the
button.
6. Select [Execute] with the c / d buttons, and
press the
button.
6
„ Deleting an image will not affect sequential image numbering. For example, if you delete image
number 240, the next captured image will be numbered 241 even though 240 no longer exists. In
other words, an image-number is retired when an image is deleted and will not be reused or
reassigned to another subsequently captured image.
EN-27
MENU OPTIONS
Capture Menu
This menu is for the basic settings to be used when capturing still images.
1. Press the
button to [ ].
2. Press the
button, and select the [Capture] / [Function] menu with the e / f
buttons.
3. Select the desired option item with the c / d buttons, and press the
button to
enter its respective menu.
4. Select the desired setting with the c / d buttons, and press the
button.
5. To exit from the menu, press the
button.
Scene Mode
Select from 20 different scene modes in accordance with the shooting conditions.
* Program AE / Anti Shake / Panorama / Portrait Man / Portrait Lady / Landscape / Sports /
Night Portrait / Night Scene / Candlelight / Fireworks / Text / Sunset / Sunrise / Splash Water
/ Flow Water / Snow / Beach / Pets / User Setting
Size
This sets the size of the image that will be captured.
*[
*[
*[
*[
*[
] 3264 x 2448
] 2816 x 2112
] 2272 x 1704
] 1600 x 1200
] 640 x 480
Quality
This sets the quality (compression) at which the image is captured.
*[
*[
*[
] Fine
] Standard
] Economy
EN-28
Sharpness
This sets the sharpness of the image that will be captured.
* Hard / Normal / Soft
Saturation
This sets the saturation of the image that will be captured.
* High / Normal / Low
White Balance
This sets the white balance for a variety of lighting conditions and permits images to be
captured that approach the conditions that are seen by the human eye.
* [ Blank ] Auto
*[
] Incandescent
*[
] Fluorescent 1
*[
] Fluorescent 2
*[
] Daylight
*[
] Cloudy
*[
] Manual
Manual WB
This manually sets the white balance and stores it. Use of this is convenient when the white
balance does not offer a good match.
Before selecting [Execute] and before taking your image, place a white paper in the scene and
set the white balance manually.
* Cancel / Execute
ISO
This sets the sensitivity for capturing images. When the sensitivity is raised (and the ISO figure
is increased), photography will become possible even in dark locations, but the more pixelated
(grainier) the image will appear.
* [Blank] Auto
*[
] ISO 64
*[
] ISO 100
*[
] ISO 200
*[
] ISO 400
*[
] ISO 800
*[
] ISO 1600
Metering
This sets the metering method for calculating the exposure.
* Center: Averages the light metered from the entire frame, but gives greater weight to the
subject matter at the center.
* Multi: The entire area of the screen is measured, and the exposure is calculated.
* Spot: A very small portion of the center of the screen is measured to calculate the correct
exposure.
Color
This sets the color of the image that will be captured.
* Normal / Vivid / Sepia / Monochrome / Blue / Red / Green / Yellow / Purple
EN-29
Capture Mode
This sets the recording method at the time of capturing images.
* [ Blank ] Single: Captures one image at a time.
*[
]
Continuous: Permits continuous capture of up to 3 images.
*[
]
AEB: Permits 3 consecutive images in the order of standard exposure,
underexposure and overexposure compensation.
*[
]
Burst:Permits continuous photography while pressing holding the shutter button.
As long as you hold the shutter button pressed, images are captured until
the memory capacity is exhausted.
*[
]
Series+flash: Permits continuous capture of up to 3 images with flash.
*[
]
Pre-Shot: Lets you capture the background first, then have someone to capture you in
front of it.
*[
]
Couple Shot: Uses separate areas to combine two shots. You can include
yourself in the shot.
„ In [Continuous], [AEB], [Burst], [Series+flash], [Pre-Shot] and [Couple Shot] capture mode, the
[Voice Memo] is automatically fixed at [Off].
Voice Memo
Refer to section in this manual titled "Recording Voice Memos" for further details.
LCD Bright.
Select a brightness level for the LCD monitor.
The LCD becomes brighter with the c button and darker with the d button. The
adjustment range is from -5 to 5.
Digital Zoom
This sets whether or not to use digital zoom at the time of photography.
* On / Off
Date Print
The date of recording can be printed directly on the still images. This function must be
activated before the image is captured.
* On / Off
EN-30
Video Menu
This menu is for the basic settings to be used when recording video clips.
1. Press the
button to [ ].
2. Press the
button, and select the [Capture] / [Function] menu with the e / f
buttons.
3. Select the desired option item with the c / d buttons, and press the
button to
enter its respective menu.
4. Select the desired setting with the c / d buttons, and press the
button.
5. To exit from the menu, press the
button.
Size
This sets the size of the video clip that will be captured.
*[
*[
] 640 x 480
] 320 x 240
Quality
This sets the quality (compression) at which the video clip is captured.
*[
*[
] Fine
] Standard
Color
This sets the color of the video clip that will be captured.
* Normal / Vivid / Sepia / Monochrome / Blue / Red / Green / Yellow / Purple
Audio
This sets whether or not to record audio at the time of video recording.
* On / Off
LCD Bright.
Refer to section in this manual titled “LCD Bright.” in Capture Menu for further details.
Digital Zoom
Refer to section in this manual titled “Digital Zoom” in Capture Menu for further details.
EN-31
Playback Menu
In the [ ] mode, choose which settings are to be used for playback.
1. Press the [ ] button.
2. Press the
button.
3. Select the desired option item with the c / d buttons, and press the
button to enter its
respective menu.
4. Select the desired setting with the c / d buttons, and press the
button.
5. To exit from the menu, press the
button.
Fix Red Eyes
Refer to section in this manual titled “Removing Red-eye” for further details.
Slide Show
This function enables you to playback your still images automatically in order one image at a time.
* 3 sec. / 5 sec. / 10 sec.
Protect
Refer to section in this manual titled “Protecting Images” for further details.
Voice Memo
Refer to section in this manual titled “Attaching Voice Memos” for further details.
LCD Bright.
Refer to section in this manual titled “LCD Bright.” in Capture Menu for further details.
Resize
Resizes a previously saved image. Resizing replaces the original image with the changed
image. It is only possible to resize to a smaller size.
Quality
Changes the quality (compression) of a recorded image. Compresses images down to half
of their size or less, overwrites old size images with newly compressed images. It is only
possible to reduce the image quality/size, never to increase it.
Copy to Card
Allows you to copy your files from the camera’s internal memory to an SD/SDHC memory
card. Of course, you can only do this if you have a memory card installed and some files in
internal memory.
* Cancel / Execute
EN-32
Setup Menu
Set your camera’s operating environment.
1. Toggle the
button to [
] or [ ]; or press the [ ]
button.
2. Press the
button, and select the [Setup] menu with the
f button.
3. Select the desired option item with the c / d buttons, and
press the
button to enter its respective menu.
4. Select the desired setting with the c / d buttons, and press
the
button.
5. To exit from the menu, press the
button.
Beep
This sets whether or not to mute the camera sound each time you
press the camera's buttons.
* On / Off
Fr. No. Reset
This creates a new folder. The captured images are recorded
to the newly created folder from number 0001.
* Cancel / Execute
Auto Off
If no operation is performed for a specific period of time, the
power to the camera is automatically turned off. This feature is
useful for reducing battery usage.
* 1 Min. / 2 Min. / 3 Min. / Off
Date/Time
Refer to section in this manual titled “Setting the Date and
Time” for further details.
Sys. Reset
This returns all basic settings to the camera’s default settings. The
time setting will not be reset.
* Cancel / Execute
Language
Refer to section in this manual titled “Choosing the Language”
for further details.
Format
Refer to section in this manual titled “Formatting the Memory Card or Internal Memory” for
further details.
Media Info.
This displays the free capacity of the internal memory or the memory card.
System Info.
This displays the firmware version of the camera.
Video Output
This sets your camera to match the system of the equipment that you are going to connect to the camera.
* PAL / NTSC
EN-33
TRANSFERRING FILES TO YOUR
COMPUTER
System Requirement
Windows
„
„
„
„
„
„
Pentium III 600 MHz or higher
Windows 2000/XP/Vista
128MB RAM
128MB hard disk space
CD-ROM drive
Available USB port
Macintosh
„
„
„
„
„
„
PowerPC G3/G4/G5
OS 9.0 or later
128MB RAM
128MB hard disk space
CD-ROM drive
Available USB port
Downloading Your Files
1. Connect one end of the USB cable to an available
USB port on your computer.
2. Connect the other end of the USB cable to the
USB terminal on the camera.
3. Turn on your camera.
4. Select [PC] using the c / d buttons and press
the
button.
5. From the Windows desktop, double click on “My
Computer”.
6. Look for a new “removable disk” icon.
„ This “removable disk” is actually the memory (or memory card) in your camera.
Typically, the camera will be assigned drive letter “e” or higher.
7. Double click on the removable disk and locate the DCIM folder.
8. Double click on the DCIM folder to open it to find more folders.
„ Your recorded images and video clips will be inside these folders.
9. Copy & Paste or Drag-N-Drop image and video files to a folder on your computer.
Mac users: Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
EN-34
USING THE CAMERA AS A PC CAMERA
Your camera can act as a PC camera, which allows you to videoconference with business associates, or have a real-time conversation with friends or family. To use the camera for videoconferencing, your computer system must include the items as below:
„ Microphone
„ Sound card
„ Speakers or headphones
„ Network or Internet connection
1. After installing the PC camera driver (included on the CD-ROM) in your Windows
operating system, restart your computer.
2. Connect one end of the USB cable to the USB terminal of the camera.
3. Connect the other end of the USB cable to an available USB port on your computer.
4. Turn on your camera.
5. Select [PC Camera] with the c / d buttons and press the
button.
6. Position the camera steadily on top of your computer monitor or use a tripod.
7. Launch the videoconferencing application software.
„ Simply follow the instructions in the application software to start your camera.
„ This function is not supported by Mac.
„ You are recommended to use MediaOne Gallery SE (included on the CD-ROM) or Windows
Netmeeting (Windows Meeting Space on Windows Vista) as a videoconferencing application
software.
„ The video resolution for videoconferencing applications is generally 320 x 240.
„ For more information about the operation of videoconference application software, refer to its
respective help documentation.
EN-35
EDITING SOFTWARE INSTALLATION
There are 2 types of software that are included on the CD-ROM:
MediaOne Gallery SE - makes it the easiest way to manage and share your digital life
with family & friends. The intuitive thumbnail library automatically organizes, updates
and sorts files for the most natural way to browse your multimedia collection.
COOL 360 SE - combines ease-of-use, power and flexibility to allow even novice digital
imaging enthusiasts to move beyond traditional photos into immersive imaging. Its
intuitive interface and easy-to-use wizard deliver great-looking panoramas while
advanced warping, blending and alignment tools ensure excellent results.
To install software:
1. Insert the CD-ROM that came with the camera into your CD-ROM drive.
The welcome screen appears.
2. Click the respective software name.
Follow the on-screen instructions to complete the installation.
„ For more information about the operation of the software, refer to its respective help documentation.
„ For Windows 2000/XP/Vista users, please make sure to install and use the software in
“Administrator” mode.
„ The software is not supported by Mac.
„ COOL 360 SE is not supported by Windows Vista.
EN-36
SPECIFICATIONS
Item
Description
Image sensor
1/2.5” CCD sensor (8.1 megapixels)
Image resolution
<Still image>
3264 x 2448, 2816 x 2112, 2272 x 1704, 1600 x 1200, 640 x 480
<Video clip>
640 x 480 (30 fps), 320 x 240 (30 fps)
LCD monitor
2.8” full color TFT LCD (230K pixels)
Recording media
32MB internal memory (28MB available for image storage)
Supports SD/SDHC memory card (up to 4GB) (optional)
File format
JPEG, DCF 1.1, EXIF 2.2, AVI
Lens
3x optical zoom lens
Aperture range: 2.9(W) - 5.2(T)
Focal length:5.7mm - 17.1mm (equivalent to 34mm - 102mm on a
35mm camera)
Focus Range
Standard
0.4m to infinity
Macro
Wide: 0.1m to infinity
Tele: 0.35m to infinity
Shutter speed
1/2 - 1/2000 sec.
Sensitivity
<Still image>
Auto (ISO 64-200)
Manual (ISO 64/100/200/400/800/1600)
* Sensitivity is measured in compliance with the ISO standard
(ISO12232:2006).
Digital zoom
4x (Capture mode)
4x (Playback mode)
Flash effective
range
0.5m - 2.4m (Wide)
0.5m - 2.1m (Tele)
Terminals
AV OUT
USB 2.0 compliant
(2 in 1 terminal)
Power supply
Rechargeable Lithium-ion battery (3.7V)
Operating
environment
Temperature: 0°C - 40°C (32°F to 104°F)
Humidity: 10% - 85% (Non-condensing)
Dimensions
Approx. 92.8 x 57.8 x 18.7mm (without protruding parts)
Weight
Approx. 114g (without battery and memory card)
* Design and specifications are subject to change without notice.
EN-37
APPENDIX
Possible Number of Shots
Possible number of shots (still image)
The table shows the approximate shots that you can capture at each setting based on
the capacity of the internal memory and the SD/SDHC memory card.
Size
Quality
Fine
3264 x 2448
Standard
Economy
Fine
2816 x 2112
Standard
Economy
Fine
2272 x 1704
Standard
Economy
Fine
1600 x 1200
Standard
Economy
Fine
640 x 480
Standard
Economy
SD/SDHC memory card capacity
Internal
Memory
128MB
256MB
512MB
1GB
6
14
16
14
18
20
25
27
31
47
57
63
118
138
177
28
62
72
62
82
90
108
121
138
206
246
273
509
595
762
89
125
146
126
166
181
219
243
278
415
494
549
1024
1197
1531
117
253
293
253
334
364
440
489
559
834
993
1102
2055
2401
3072
235
507
588
508
669
730
881
980
1120
1671
1989
2208
4115
4810
6153
2GB
4GB
SDHC
472
945
1015 2033
1177
2357
1018 2038
1340 2684
1461 2925
1765 3533
1963 3929
2242 4489
3345 6695
3982 7969
4420 8847
8237 16485
9627 19268
12316 24649
Possible recording time / sec (video clip)
Size
Quality
Fine
Internal
Memory
SD/SDHC memory card capacity
128MB
256MB
512MB
1GB
2GB
4GB
SDHC
00:00:17 00:01:00 00:02:01 00:04:03 00:08:07 00:16:15 00:32:31
640 x 480
Standard 00:00:18 00:01:06 00:02:13 00:04:27 00:08:54 00:17:50 00:35:42
320 x 240
Standard 00:00:57 00:03:25 00:06:54 00:13:50 00:27:43 00:55:29 01:51:02
Fine
00:00:50 00:02:57 00:05:57 00:11:56 00:23:55 00:47:52 01:35:49
* We recommend a memory card of at least 10MB/Sec write speed to prevent auto stop or
unexpected results. If you experience an error using a slower SD/SDHC memory card, you
can set your camera’s video recording to QVGA (320 x 240) and standard quality.
EN-38
Troubleshooting
Refer to the symptoms and solutions listed below before sending the camera for repairs.
If the problem persists, contact your local reseller or service center.
Symptom
Cause
Solutions / Corrective Actions
The power does not come
on.
The battery is not inserted.
Insert the battery correctly.
The battery is exhausted.
Recharge the battery.
The battery runs out
quickly.
The battery is not fully charged.
The battery is not used for an
extended period of time after
being charged.
Fully charge the battery and
discharge it for at least one
complete cycle before use to
maximize its performance and
lifetime.
The battery or camera feels Long period of continuous use of
warm.
the camera or the flash.
Even if I press the shutter
button, the camera does
not take a picture.
The shutter button is not pressed Press the shutter button all the
all the way down.
way down.
The memory card does not have Insert a new memory card, or
delete unwanted files.
any free capacity.
The memory card is
write-protected.
Remove the write-protection.
Images do not appear on LCD monitor is dark.
the LCD monitor.
Adjust the brightness of the
LCD monitor in the menu.
Although it is set to auto The lens is dirty.
focus, it does not focus.
Wipe clean with a soft, dry cloth
or lens paper.
The distance to the subject is
Get your subject within
smaller than the effective range. effective focus range.
The contents on the You played back a memory card
memory card cannot be that was not formatted by this
played back.
camera.
Insert a memory card that was
formatted on this camera.
Files cannot be deleted.
the
The file is protected.
Cancel protection.
The memory card is
write-protected.
Remove the write-protection.
Even when the camera’s
buttons are pressed, it
does not operate.
The battery is running low.
Recharge the battery.
The date and time are
wrong.
The correct date and time is not
set.
Set the correct date and time.
Cannot download images.
The free space on the hard disk Check whether the hard disk has
in your computer may be
space for running Windows, and
insufficient.
if the drive for loading image files
has a capacity at least that of the
memory card inserted in the camera.
No power supply.
Recharge the battery.
EN-39
Connecting to a PictBridge Compliant Printer
If a printer that supports PictBridge is available, images can be printed by connecting the
digital still camera directly to the PictBridge-compatible printer without using a computer.
Connecting the camera to the printer
1. Connect one end of the USB cable to your
camera.
2. Connect the other end of the USB cable to the
USB port on the printer.
3. Turn on your camera.
4. The [USB] screen is displayed. Select
[PictBridge] with the c / d buttons, and press
the
button.
Printing images
When the camera is properly connected to a PictBridge compliant printer, the PictBridge
menu is displayed on the monitor.
1. Select the item you want to configure with the
c / d buttons, and press the
button.
„ [Images]:Select whether you want to print
specific image or all images. You may also
select printing number for specific image.
„ [Date Print]:According to the printer type,
select whether you want to print the image
with date imprint or not.
„ [Paper Size]:Select the desired paper size
according to the printer type.
„ [Layout]:Select the desired printing layout according to the printer type.
„ [Print]:After all settings are configured, select this item to start printing.
2. If you select [Images] in the previous step, the
figure shown on the right hand side will appear.
Select [Single] or [All] with the c / d buttons,
and press the
button.
„ [Single]:Select to print one specific image.
„ [All]:Select to print all images.
„ [Exit]:Exit from Images option.
EN-40
3. If you select [Single] in the previous step, the
figure shown on the right hand side will appear.
„ Select the image that you want to print with
the e / f buttons.
„ Select the [Print Num] (up to 99) with the c /
d buttons.
„ After selecting the desired image and printing
number, press the
button to confirm.
4. Select [Exit] with the c / d buttons, and press
the
button.
5. Select [Print] with the c / d buttons, and press
the
button to start printing.
6. The printing starts and the figure shown on the
right hand side appears.
USB
„ [COMPLETE] will be displayed temporarily,
reminding you that the printing procedure is
finished.
PRINTING
„ If an error is detected during the connection
(i.e. the printer hardware problem) between
camera and printer, [PRINT ERROR] will be
displayed.
„ If an error is detected during the communication
(i.e. wrong setting on the camera) between camera and printer, [ERROR] will be
displayed.
„ The image printing may fail if the power to the camera is cut off.
EN-41
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising