• Installation Instructions • Use and Care Information

• Installation Instructions • Use and Care Information
AGIO
Under Cabinet Tiltout Rangehood
• Installation Instructions
• Use and Care Information
READ AND SAVE THESE INSTRUCTIONS
The Installer must leave these instructions with the homeowner. The homeowner must keep these instructions for
future reference and for local electrical inspectors' use.
READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Always
turn hood ON when cooking at high heat or when cooking flaming foods. Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter. Use proper pan size. Always use cookware appropriate for the size of the
surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE
THE FOLLOWING: SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT.
NEVER PICK UP A FLAMING PAN - You may be burned. DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result. Use an extinguisher ONLY if: 1. You know you have a Class ABC extinguisher, and
you already know how to operate it. 2. The fire is small and contained in the area where it started. 3. The fire department
is being called. 4. You can fight the fire with your back to an exit.
ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED.
This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking surface or countertop.
This minimum clearance may be higher depending on local building code. For example, for gas ranges, a minimum of 30" may
be required. The maximum depth of overhead cabinets is 13". Overhead cabinets on both sides of this unit must be a minimum
of 18" above the cooking surface or countertop. Consult the cooktop or range installation instructions given by the manufacturer
before making any cutouts. MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured
Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD, Part 280). Four wire power supply must be used and the appliance wiring must be revised. See Electrical
Requirements.
LISEZ BIEN CETTE FICHE AVANT D'INSTALLER LA HOTTE
AVERTISSEMENT - POUR MINIMISER LE RISQUE D’UN FEU DE GRAISSE SUR LA TABLE DE CUISSON : Ne jamais
laisser un élément de la table de cuisson fonctionner sans surveillance à la puissance de chauffage maximale; un renversement/débordement de matière graisseuse pourrait provoquer une inflammation et le génération de fumée. Utiliser
toujours une puissance de chauffage moyenne ou basse pour le chauffage d’huile. Veiller à toujours faire fonctionner
le ventilateur de la hotte lors d’une cuisson avec une puissance de chauffage élevée ou lors de la cuisson d’un mets à
flamber. Nettoyer fréquemment les ventilateurs d’extraction. Veiller à ne pas laisser de la graisse s’accumuler sur les
surfaces du ventilateur ou des filtres. Utiliser toujours un ustensile de taille appropriée. Utiliser toujours un ustensile de
taille adapté à la taille de l’élément chauffant.
AVERTISSEMENT: - POUR PRÉVENIR LES BLESSURES EN CAS DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES:
ÉTOUFFEZ LE FEU avec un couvercle métallique et fermez le brûleur. Si le feu ne s'éteint pas tout de suite, QUITTEZ
LES LIEUX ET APPELEZ LES POMPIERS. NE TOUCHEZ JAMAIS UNE CASSEROLE EN FLAMMES. N'UTILISEZ JAMAIS
DE L'EAU ou un torchon mouillé pour éteindre le feu - ce qui pourrait causer une explosion de vapeur. N'utilisez un
extincteur que si: 1. Vous avez un modèle ABC et vous connaissez bien son mode d'emploi. 2. Le feu est petit et peu
répandu. 3. Les pompiers sont déjà prévenus. 4. Vous avez une sortie derrière vous.
TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE DOIT ÊTRE SCELLÉ
Gardez 24 po. de hauteur entre le bas de la hotte et la surface de cuisson. Cette hauteur minimum peut être plus haute suivant le
code municipal. Par exemple, les cuisinières à gaz peuvent requérir 30 po. de hauteur. Les armoires au-dessus ne dépasseront
pas 13 po. de profondeur. Les armoires au-dessus de chaque côté devront être au moins à 18 po. au-dessus de la surface
de cuisson. Consultez la fiche technique avant de découper les armoires. L'installation de cette hotte doit être conforme aux
Réglements de Manufactured Home Construction and Safety Standards, titre 24 CFR, Section 3280 (anciennement Federal
Standard for Mobile Home Construction and Safety Standards, titre 24 CFR, Section 3280 (anciennement Federal Standard for
Mobile Home Construction and Safety, titre 24, HUD, Section 280). Le branchement électrique se fait avec une raccordement à
4 fils. Consultez la fiche technique électrique.
Version 05/04 - Page 1
VENTING REQUIREMENTS
Determine which venting method is best for your application.
Ductwork can extend either through the wall or the roof.
The length of the ductwork and the number of elbows should
be kept to a minimum to provide efficient performance. The
size of the ductwork should be uniform. Do not install two
elbows together. Use duct tape to seal all joints in the ductwork
system. Use caulking to seal exterior wall or floor opening
around the cap.
Flexible ductwork is not recommended. Flexible ductwork
creates back pressure and air turbulence that greatly
reduces performance.
Make sure there is proper clearance within the wall or floor
for exhaust duct before making cutouts. Do not cut a joist or
stud unless absolutely necessary. If a joist or stud must be
cut, then a supporting frame must be constructed.
FOR MORE SPECIFIC DUCTWORK INFORMATION, GO
TO PAGE 4.
WARNING - To Reduce The Risk Of Fire, Use Only Metal
Ductwork.
!
WARNING
• Venting system MUST terminate outside the
home.
• DO NOT terminate the ductwork in an attic or
other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOT obstruct the flow of combustion and
ventilation air.
• Failure to follow venting requirements may result
in a fire.
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate
15 amp fused circuit. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with
the electrical rating of this unit as specified on the serial/rating plate
located inside the unit near the field wiring compartment. THIS UNIT
MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes
must conform to the requirements of the National Electrical Code,
ANSI/NFPA 70 - latest edition, and all local codes and ordinances.
Wire size and connections must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:
National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
This appliance should be connected directly to the fused
disconnect (or circuit breaker) through flexible, armored or
nonmetallic sheathed copper cable. Allow some slack in the
cable so the appliance can be moved if servicing is ever necessary. A UL Listed, 1/2" conduit connector must be provided
at each end of the power supply cable (at the appliance and
at the junction box).
When making the electrical connection, cut a 1 1/4" hole
in the wall. A hole cut through wood must be sanded until
smooth. A hole through metal must have a grommet.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, do not use this fan with any solid-state speed
control device.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING: Use this unit only in the manner intended
by the manufacturer. If you have any questions, contact
the manufacturer.
Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a
tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not
Use To Exhaust Hazardous or Explosive Materials and
Vapors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING: Installation Work And Electrical Wiring Must
Be Done By Qualified Person(s) In Accordance With All
Applicable Codes And Standards, Including Fire-Rated
Construction.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Ducted fans must always be vented to the outdoors.
!
WARNING
• Electrical ground is required on this rangehood.
• If cold water pipe is interrupted by plastic,
nonmetallic gaskets or other materials, DO NOT
use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding
circuit. A fuse in the neutral or grounding circuit
could result in electrical shock.
• Check with a qualified electrician if you are in doubt
as to whether the rangehood is properly grounded.
• Failure to follow electrical requirements may result
in a fire.
For residential use only.
Version 05/04 - Page 2
RÈGLEMENTS D'ÉVACUATION
Confirmer la sortie d'évacuation - soit par le mur, soit par
le toit.
AVERTISSEMENT - POUR RÉDUIRE LE RISQUE
D'INCENDIE OU DE CHOC ELECTRIQUE, ne pas utiliser
ce ventilateur en conjonction avec un dispositif de réglage
de vitesse à semi-conducteurs.
Utilisez une longueur de tuyauterie minimale avec les moindres
de coudes pour la plus grande efficacité. Le diamètre de
tuyauterie doit être uniforme. N'installez jamais 2 coudes
ensemble. Scellez bien tous les joints avec un ruban adhésif
métallique à l'intérieur et scellez bien le clapet extérieur avec
du calfeutrage.
AVERTISSEMENT – POUR MINIMISER LES RISQUES
D’INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES
CORPORELS, OBSERVER LES PRESCRIPTIONS
SUIVANTES: Suivez les recommandations du fabricant
et entre en communication avec lui pour toute
information.
Utilisez un tuyau d'évacuation rigide lorsque possible.
Un tuyau flexible égale deux fois plus qu'un tuyau rigide,
ce qui réduit la puissance d'évacuation. Un conduit
d'évacuation flexible crée une contre-pression et une
turbulence de l'air qui réduisent considérablement la
performance.
Fermez le courant avant tout entretien et veillez a ce qu'il
reste fermé. Si on ne peut pas verrouiller le panneaux
du service électrique, affichez un avis de danger sur la
porte.
Veillez à ce que l'espace pour le tuyau soit ample - ainsi on
n'aurait pas besoin de découper les supports de mur intérieur.
Si ce découpage est nécessaire, veillez bien à ce qu'un
renforcement soit mis en place.
RÈGLEMENTS D'ÉVACUATION ADDITIONELL PAGE 8.
AVERTISSEMENT - Pour Ne Pas Risquer Un Feu, Utilisez
Seulement Les Matériaux Métalliques.
! AVERTISSEMENT
• Le système d'évacuation DOIT sortir à l'extérieur.
• N'ÉVACUEZ PAS le conduit soit dans une
mansarde soit dans un espace enfermé.
• N'UTILISEZ PAS un clapet de séchoir à 4 pouces.
• N'utilisez pas un conduit flexible.
• N'ENCOMBREZ PAS la circulation d'air.
• Faute de suivre cet avertissement pourrait
occasionner un feu.
AVIS: Pour L'évacuation Générale - Veillez à Ne Pas
Evacuer Des Matériaux Ou Vapeurs Explosif.
AVERTISSEMENT – POUR MINIMISER LES RISQUES
D’INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES
CORPORELS, OBSERVER LES PRESCRIPTIONS
SUIVANTES: L'installation Et Le Raccordement Electrique
Doivent Se Faire Par Un Technicien Qualifié Selon Tous
Les Codes Municipaux.
Afin d'obtenir un rendement maximal en ce qui a trait à la
combustion ainsi qu'à l'évacuation des gaz par la conduite
de cheminée, une bonne aération est nécessaire pour
tous les appareils à combustion. Suivez les conseils et
mesures de sécurité du fournisseur tels que ceux publiés
par l'Association Nationale de la Sauvegarde contre
l'Incendie et l'Association Américaine d'Ingénieurs de
Chauffage, Frigorifaction et Air Climatisé ainsi que les
codes municipaux.
En perçant un mur veillez à ne pas perforer un autre fil
électrique.
Une ventilateur à évacuation extérieure doit être raccordée
à l'extérieur.
FICHE TECHNIQUE ÉLECTRIQUE
Le raccordement électrique doit se faire avec un circuit séparé
de 15 ampères fusible à 120V, 60 Hz, courant alternant. On
recommande un coupe-circuit. La taille du fusible doit se
conformer aux codes municipaux suivant la spécification
électrique sur la plaque intérieure. Le diamètre du fil
devra aussi se conformer aux règlements du code national
électrique, ANSI/NFPA 70 - ainsi qu'aux règlements locaux
et les spécifications de cet appareil. On peut obtenir ces
informations chez:
l'Association Nationale de la Prévention du Feu
Batterymarch Park
Quincy, Massachusetts 02269
Raccordez cet appareil directement au coupe-circuit avec un fil
flexiblle couvert en cuivre en laissant un peu de lâchement dans
le fil pour permettre le déplacement de l'appareil. Veillez a ce
qu'un contact d'un demi-pouce (1/2 po.) soit installé à chaque
bout de fil (soit à l'appareil ainsi qu'à la boite à fusible).
Faites un trou de 1 1/4 po. dans le mur. S'il s'agit d'un trou en
bois - sablez-le bien, tandis qu'un trou passant par le métal
demande un bouche-trou.
! AVERTISSEMENT
• Une prise à terre est nécessaire pout cette hotte.
• N'utilisez pas un tuyau à l'eau froide pour la mise
à terre s'il est branché à un joint plastique, nonmétallique ou autre.
• NE JOIGNEZ PAS la mise à terre à conduit de gaz.
• N'INSTALLEZ PAS un fusible dans le circuit de
mise à terre - ce qui peut causer une secousse
électrique.
• Vérifiez avec un électricien certifié à ce que la hotte
soit bien mise à terre.
• Faute de suivre ces recommandations pourrait
occasionner un feu.
Uniquement pour usage menager.
Version 05/04 - Page 3
TOOLS NEEDED FOR INSTALLATION
• Saber Saw or Jig Saw
• Drill
• 1 1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Flat Blade Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun
• Duct Tape
DUCTLESS
INSTALLATION
FIGURE 3
CALCULATE THE DUCTRUN LENGTH
The ductrun should not exceed 25 equivalent feet if ducted with the
required minimum of 3 1/4" by 10" rectangular duct. Calculate the
length of the ductwork by adding the equivalent feet in FIGURE 4
for each piece of duct in the system. An example is given in FIGURE
5. For best results, use no more than three 90° elbows. Make
sure that there is a minimum of 24" of straight duct between
elbows if more than one is used. Do not install two elbows
together. If you must elbow right away, do it as far away from
the hood's exhaust opening as possible.
PARTS SUPPLIED FOR INSTALLATION
• 1 Backdraft Damper
• 4 Black Screws & 4 Silver Screws
• 1 Literature Package
PARTS NEEDED FOR INSTALLATION
• 2 Conduit Connectors
• Power Supply Cable
• 1 Wall or Roof Cap
• All Metal Ductwork
3.0 feet
5.0 feet
12.0 feet
45˚ Elbow
90˚ Elbow
90˚ Flat Elbow
OPTIONAL ACCESSORIES AVAILABLE
• Charcoal Filters
For non-vented installations only,
replace charcoal filters as needed
part # 6093032
Wall Cap
PLAN THE DUCTWORK
The Agio convertible rangehood is designed to offer wide
flexibility of installations. The rangehood can be ducted
vertically or horizontally through a 3 1/4" X 10" rectangular
vent. The unit can also be installed in a ductless recirculating
configuration. FIGURES 1 and 2 show horizontal and vertical
duct installations for this rangehood. FIGURE 3 shows the
exhaust opening for ductless installation.
HORIZONTAL
DUCTING
FIGURE 4
0.0 feet
9 Feet Straight Duct 9.0 feet
2 - 90˚ Elbows
10.0 feet
Wall Cap
0.0 feet
Total System
FIGURE 5
19.0 feet
PLAN THE DUCTWORK
First, determine which venting option will be used:
• Horizontal
• Vertical
• Ductless
For Horizontal and Vertical ducting, the ductwork cutout dimensions
are given in FIGURE 6. For ductless installations, read the section
discussing ductless installations before you make any cutouts or
modifications to the rangehood. Ductless installations require
Charcoal Filters.
30" or 36" or 23 5/8" (60 cm)
FIGURE 1
VERTICAL
DUCTING
30" or 36" or 23 5/8" (60 cm)
FIGURE 6
FIGURE 2
Version 05/04 - Page 4
30" or 36" or 23 5/8" (60 cm)
FIGURE 7
PREPARE THE CABINET
1. Disconnect and move freestanding range from cabinet
opening to provide easier access to upper cabinet and rear
wall. Put a thick, protective covering over cooktop, set-in
range or countertop to protect from damage or dirt.
2. Determine and clearly mark with a pencil the center line
of the cabinet on the wall and on the underside of the cabinet
where the rangehood will be installed.
3. The Agio attaches to the cabinet by four black screws.
Mark the cabinet and insert the screws into the underside
of the cabinet as shown in FIGURE 8. Do not tighten the
screws.
30" or 36" or 23 5/8" (60 cm)
FIGURE 9
INSTALL THE RANGEHOOD
1. Remove the unit from the carton and place on a flat
surface for assembly. Make sure to cover the surface to
prevent accidental damage. Remove all parts including the
Backdraft Damper, Screws, and Literature Package before
discarding the carton.
2. Remove both grease filters from the unit and set aside.
The rangehood is shipped from the factory with the backdraft
damper attached inside. Using a Phillips head screwdriver,
remove the backdraft damper by loosening the screw marked
with a red dot on top of the rangehood.
30" or 36" or 23 5/8" (60 cm)
FIGURE 8
4. Determine the proper cutouts for the ductwork. Make
all necessary cuts in the walls or cabinets for the ductwork.
Install the ductwork before mounting the rangehood.
5. Determine the proper location for the Power Supply
Cable. Both possible locations are given in FIGURE 9. Use
a 1 1/4" Drill Bit to make this hole. Run the Power Supply
Cable. Use caulking to seal around the hole. DO NOT turn
on the power until installation is complete.
3. Before installing, the rangehood must be adjusted for
venting. For ductless installations, read the following section
which discusses special requirements for these installations
before continuing.
For Horizontal or Vertical ducting, the respective exhaust
knockout must be removed. Each knockout is attached to the
rangehood by four points. Using a flat blade screwdriver or
utility knife, remove the exhaust knockout. Save this plate as
it must be used to block the ductless exhaust grill. FIGURE
10 shows the location of the knockouts for both horizontal
and vertical. ONLY ONE must be removed.
Version 05/04 - Page 5
11. Replace the field wiring compartment cover. For ductless installations, refer to the next section which discusses
ductless installations. Replace the grease filters.
12. Turn the power supply on. Turn on blower and light.
IF THE RANGEHOOD DOES NOT OPERATE:
FIGURE 10
4. Remove the central support and control box by removing the screws indicated in FIGURE 11. It is not necessary
to remove the blower to perform this operation.
• Check that the circuit breaker is not tripped or the
house fuse blown.
• Disconnect the power supply and check that the
wiring connections have been made properly.
DUCTLESS INSTALLATIONS
For ductless installations, the blower must be positioned with
the exhaust pointing forward ( so that the exhaust exits from
the front grill ) before attaching the rangehood to the cabinet.
Ductless installations require Charcoal Filters.
1. Remove both grease filters, the central support and the
control box. Remove the two thumb screws on either side of
the blower and remove the blower from the mounting guides
as indicated in FIGURE 11.
FIGURE 11
5.
Attach the cover behind the exhaust grate with two silver
screws supplied with the rangehood as indicated in FIGURE 12.
2. Rotate the blower 180° so that the exhaust points out
the front of the rangehood. Replace the two thumb screws
and tighten so that the blower is securely fastened inside the
rangehood as indicated in FIGURE 13. Reattach the control
box and central support. Make sure that the wiring harness
is concealed behind the central support.
FIGURE 12
6. Reattach the control box and support. Make sure that
the wiring harness is concealed behind the support.
7. Remove the field wiring compartment cover. Feed the
Power Supply Cable through the electrical knockout.
8. Attach the backdraft damper to the proper exhaust opening using two silver screws supplied with the rangehood.
FIGURE 13
3. For ductless installations, Charcoal Filters are required
and must be installed before the grease filters are replaced.
The charcoal filters attach to both ends of the blower as
indicated in FIGURE 14.
9. Attach the rangehood to the cabinet bottom. The four
key holes slip onto the four screws mounted to the cabinet
bottom. Tighten the screws.
10. Connect the Power Supply Cable to the rangehood.
Attach the White lead of the power supply to the White lead
of the rangehood with a twist-on type wire connector. Attach
the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector. Connect
the Green (Green and Yellow) ground wire under the Green
grounding screw.
FIGURE 14
Version 05/04 - Page 6
CUSTOMIZING YOUR RANGEHOOD
The front strip of the rangehood can be customized by replacing the factory supplied strip with a custom front strip made
from the same materials as your cabinets. The front strip is
attached to the rangehood by three recessed screws and
three key hole slots on the back side of the strip as indicated
in FIGURE 15. It is necessary only to remove the three lower
screws to remove the front strip. The top screws will slide out
of the key holes once the three lower screws are removed.
Side View of the Rangehood
Rangehood Body
Front
Strip
Light On/Off Switch ( L )
On/Off switch for the fluorescent light. Moving the switch to the
1 Position turns the light On. Moving the switch to the 0 Position
turns the light Off.
Blower On/Off
Switch ( M )
On/Off switch for the
blower. Moving the
switch to the 1 Position turns the blower
On. Moving the switch
to the 0 Position turns
the blower Off.
FIGURE 17
Blower Speed Switch ( S )
Controls blower speed. Moving the switch to the 1 Position turns
the blower on LOW. Moving the switch to the 2 Position turns the
blower on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH.
Three Screws
FIGURE 15
The front strip dimensions are given in FIGURE 16. For a
custom front strip, a local cabinet shop can make a strip to
match your cabinets. If you wish to keep the frame of the front
panel and only replace the glass panel, the dimensions follow:
Height = 5 11/16", Depth = 1/8", Width = 29 11/16" (for 30"
model) 35 11/16" (for 36" model) 23 5/8" (for 24" model).
5 7/8"
23 5/8" or 29 15/16" or 35 15/16"
Rangehood Control Panel
All controls are located under the front panel and are shown in
FIGURE 17.
13/16"
FIGURE 16
WIRING DIAGRAM
Operation Indicator Light ( I )
Red light will be on when the rangehood is operating.
Microswitch ( MS )
When the front panel of the rangehood is closed, the rangehood
will turn off by a microswitch. This turns the rangehood On and
Off without adjusting the switches for the Light or Blower and it
remembers the last speed setting.
Cleaning
The metal grease filters should be cleaned frequently in hot detergent solution or placed in the dishwasher. Clean exterior surfaces
with hot soapy water. Using abrasives and scouring agents can
scratch rangehood finishes and should not be used to clean finished
surfaces.
Replacing the Fluorescent Light
To replace the fluorescent light, remove the retainer clips from both
ends of the glass diffuser as indicated in FIGURE 18. Carefully
slide the glass diffuser all the way to the left. Lower the right end
of the glass below the support flange, then remove the glass by
sliding it back to the left. Replace the diffuser glass by reversing
these directions.
FIGURE 18
• This rangehood uses Flourescent Lamp Type F33-15W-T8 and
Starter Type S2.
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking
vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper
airflow. Allow the unit to operate for several minutes after cooking
is complete to clear all smoke and odors from the kitchen.
WARRANTY & SERVICE
All Faber products are warranteed against any defect in materials or
workmanship for the original purchaser for a period of 1 year from the
date of original purchase. This warranty covers labor and replacement parts. The warranty does not cover consumable parts such as
filters and light bulbs. This warranty does not apply if this product
has been subjected to faulty installation, misuse, or neglect. This
warranty excludes any consequential expense or damage resulting
from any use or malfunction of the product. All implied warranties
are limited to the duration of this warranty.
To obtain warranty service, contact the dealer from whom you purchased the rangehood, or the local Faber distributor. If you cannot
identify a local Faber distributor, contact us at (508) 358-5353 for
the name of a distributor in your area.
Version 05/04 - Page 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement