advertisement
SYSTEM
ADMINISTRATOR’S
GUIDE
Avery Dennison
®
Monarch
®
Tabletop
Printer 1
TCADTP1SA Rev. AE 11/16
© 2015 Avery Dennison Corp.
All rights reserved.
Each product and program carries a respective written warrant y, the only warrant y on which the custom er can rely. Avery Dennison Corp. reserves the right to m ake changes in the product, the program s, and their availabilit y at an y tim e and without notice. Although Avery Dennison Corp. has m ade every effort to provide com plete and accurate inform ation in this m anual, Avery
Dennison Corp. shall not be liable for an y om issions or inaccuracies. An y update will be incorporated in a later edition of this m anual.
2015 Avery Dennison Corp. All rights reserved. No part of this publication may be reproduced, transm itted, stored in a retrieval s ystem , or translated into an y language in any f orm b y an y m eans, without the prior written perm ission of Aver y Dennison Corp.
Trademarks
Monarch and MPCL are trademarks of Avery Dennison Retail Information Services LLC.
Avery Dennison® is a trademark of Avery Dennison Corp.
EPCglobal, Inc.™ and Electronic Product Code™ (EPC) are trademarks of GS1/GS1US.
T A B L E O F C O N T E N T S
TOC-i
TOC-ii
TOC-iii
TOC-iv
G E T T I N G S TA R T E D
The Avery Dennison® Monarch® Tabletop Printer 1 prints on thermal transfer
(ribbon) and thermal direct labels or tags. The printer prints labels continuously (in one
1
strip) or on-demand (one label at a time). The printer prints on aperture, die cut, black mark, or continuous (non-indexed) supplies.
A u d i en c e
This manual is for the System Administrator who configures and updates the printer.
♦
To load supplies, print labels, or how to care for the printer, refer to the Operator’s
Handbook.
♦
To create format and batch packets for printing or how to configure the printer online, refer to the Packet Reference Manual.
Monarch® MPCL™ Toolbox Utilities are available on our W eb site. However, they are not label production software. Call Customer Service for information about label production software.
U s i n g t h e Co n t ro l P an el
The control panel has a four-line LCD display and five buttons. The top three buttons are function buttons, which vary depending on the task shown above the button. The two bottom buttons are navigation buttons. Use these buttons to scroll through menus.
The LCD
♦ shows a red background when immediate attention is required for a jam or error.
♦ shows a green background when the printer is active
(printing or receiving data).
♦ shows a white background when viewing menu prompts, printer settings, button functions, etc.
M P C L
R E A D Y
1 9 2 . 0 . 0 . 1 9 2
FEED TLABEL MENU
Displa y Ic ons
The display icons indicate the following:
Icon Description Icon Description
Wireless mode active RFID successful encode
RFID successful verification
Battery life
Signal strength
Wired Ethernet mode active
USB drive installed
Getting Started 1-1
Selecting a Func tion
Use
or to see the menu options. Press SELECT when you see the menu option you need. Press CHANGE to change a setting. Press SET to save a setting.
Exiting a Func tion
There are two ways to exit an option. Pressing BACK once returns to the previous menu and saves any changes. Pressing CANCEL exits to the previous menu; however, changes are not saved.
P r i n t i n g a T e s t L ab el
From the Main Menu select TLABEL. Select from the test label options:
Printer Information
Contains generic information, including inch counts and printhead resolution.
MPCL Label
Contains the printer’s MPCL packet configuration.
Mnet2 Label
Contains the printer’s network/Ethernet configuration.
RFID Configuration
Contains the module’s Firmware Version,
Module Type, Easy Setup Version (RFID
Inlay Database), Region, Frequency, etc.
Note: There are two RFID module types: One for FCC (IPJ-RS500GX) and one for
ETSI (IPJ-RS500EU) frequency ranges.
Getting Started 1-2
Removing the Cover
1. Open the cover.
2. Unlock the printhead by turning the retaining latch.
3. Lift the printhead assembly using the printhead tab until the assembly locks into place.
4. Remove both cover thumbscrews.
5. Gently push down on the control panel release tab located inside the front cover. The control panel tilts forward.
6. Using both hands, slide the cover to the left and remove.
Getting Started 1-3
Getting Started 1-4
S E T T I N G S U P P LY O P T I O N S
This chapter explains how to select the supply type, ribbon, speed, feed mode, cut mode, backeed, print position, supply position, margin position, cut position, dispense position, backfeed distance, separators, skip index mode, rotate image, and print contrast.
2
You may limit access to this menu to prevent changes by the users. Users are prompted to enter a password when password protection is enabled.
The supply options are listed in the table below.
Option Choices
Supply Type
Ribbon
Speed
Feed Mode
Cut Mode
E Aperture/E Die Cut/E Black Mark/Continuous/ C
Aperture/C Die Cut/C Black Mark/C Tag Edge
No/Yes/High Energy
2.5/4.0/6.0/8.0/10.0/12.0/Default
Continuous/On-Demand/Liner Takeup
Disabled/Cut Each Tag/Cut Each Batch/
Mode 3/Mode 4/Mode 5
Backfeed
Print Position
Supply Position
Margin Position
Cut Position
Off/On
-450 to 450
-300 to 300
-99 to 99
-300 to 300
Dispense Position 50 to 200
Backfeed Distance 10 to 200
Separators
Skip Index
Error Action
No/Yes/Long
No/Yes
Normal
Overstrike/Continue 1x – 5x
Rotate Image No/Yes
Contrast -699 to 699
Press CANCEL to exit an option without changing the setting.
Default
E Die Cut
Yes
Default
Continuous
Disabled
Off
0
0
0
0
65
65
No
No
Normal
No
0
Setting Supply Options 2-1
S e t t i n g t h e S u p p l y T yp e
The printer can print on aperture, black mark, die cut, or continuous supplies as shown.
Set the printer’s supply type to match the loaded supplies.
Select
E Aperture
(Edge Aperture)
E Die Cut (Edge Die Cut) or
C Die Cut (Center Die Cut)
E Black Mark (Edge Black Mark) or
C Black Mark (Center Black Mark)
Die cut supplies have a rounded edge. The supply is sensed using the gap between the labels. If using semi die cut supplies (tags with rounded corners on the edges), select Edge Die Cut.
Black marks on the back of the supply for sensing.
The supply is sensed using the black mark.
Select E Black Mark for black marks on the left edge.
Select C Black Mark for black marks in the center.
Select C Black Mark for black marks across the entire width of supply.
Continuous
C Aperture (Center Aperture)
For
Aperture holes (or openings) on the left edge of the supply. The supply is sensed using the holes. You may need to make supply or print position adjustments on your format.
See description for Center Tag Edge.
Continuous supply does not have any index marks for sensing or perforations. This is also known as non-indexed supply.
Aperture holes (or openings) in the center of the supply. They do not contain a black mark. The supply is sensed using the holes.
Setting Supply Options 2-2
Center Tag Edge Center tag edge supply has aperture holes (or openings) centered on the left edge of the supply.
The supply is sensed using the holes.
Using this setting, the printer automatically calibrates to print at the leading edge. No additional supply/print position adjustments are necessary.
Note: Supply/print position adjustments and the format determine where the printing begins on the supply.
S e t t i n g t h e Ri b b o n
There are different ribbon requirements for the types of supplies:
Select To
No (for thermal direct supply) Not use a ribbon for printing.
Yes (for thermal transfer supply) Require a ribbon for printing.
Hi Energy
(High Energy Supply -
TUFF-MARK®)
Require an elevated heat setting for resin ribbon applications.
Using a High E nergy Ribbon
When you select high energy ribbon for the printer setting, you are setting the printer to a higher printing temperature. Select this setting only after you have loaded a high energy ribbon and supplies or it may damage the printhead.
High Energy Ribbon Limitations:
♦
Use a print speed of 2.5 ips.
♦
Printhead warranty is reduced to 100,000 inches.
♦
Serial bar codes cannot be printed.
♦
Do not use peel mode
♦
Reverse fonts cannot be used.
♦
Not for use on full tinted supplies.
♦
Do not print horizontal lines or bars.
♦
Graphics are limited.
♦
Requires a non-printing area at least 0.1 inch (2.54 mm) on left and right edge of ribbon.
♦
No more than 20% of the supply should have print (black coverage).
CAUTION: The high energy ribbon may break or stick to the supply when more than 20% of the supply contains print.
Setting Supply Options 2-3
S e t t i n g t h e S p e ed
Select the print speed in IPS (inches per second). If print quality is important, reduce the print speed - a lower print speed increases the print quality of labels. Use premium supplies when printing at high speeds.
Select To Select To
2.5 IPS
4.0 IPS
Print at 2.5 IPS.
Print at 4.0 IPS.
10.0 IPS
12.0 IPS
Print at 10.0 IPS.
Print at 12.0 IPS.
6.0 IPS
8.0 IPS
Print at 6.0 IPS.
Print at 8.0 IPS.
Default Print formats with serial bar codes at 2.5 inches per second and formats with parallel bar codes at
6.0 inches per second.
When using Easy Setup to configure the printer for RFID supplies, the print speed may be
decreased. For example:
Inlay Selected Speed RFID Easy Setup Configured Speed
AD-318M5GW C 8.0 IPS 6.0 IPS
Easy Setup changes the printer to print 6.0 ips.
AD-318M5GW C 4.0 IPS 4.0 IPS
Easy Setup does not adjust the print speed.
Recomme nde d Ma ximum Pint Speeds
Options:
2.5/4.0/6.0
Print Speed, inches per second
8.0 10.0
300 dpi printhead
supported supported not supported
12.0
not supported
Tags
TuffMark®
Supply
supported supported
2.5 ips maximum recommended not recommended
Serial bar codes
2.5 ips maximum recommended not recommended
Liner Take-up
supported
Cutter &
Stacker
supported supported supported not recommended not recommended not recommended not recommended not supported not supported not recommended not recommended not supported not supported
Peel Mode
supported supported not supported not supported
Bar Code
Verifier
supported not recommended not recommended not recommended
Note: If you change the speed, you must resend your formats or turn off the printer and back on before the change takes effect.
If you change the speed in offline mode, turn off the printer then turn it back on before the change takes effect.
Setting Supply Options 2-4
S e t t i n g t h e F e e d M o d e
Set the feed mode based on your application and supply type.
Note: To load supplies for liner take-up, refer to the Operator’s Handbook.
Select To
Continuous
On-Demand
Print tags or labels in one strip.
Print one label, once that label is removed, the next label prints.
Liner Take-up Print labels while the liner is collected on a take-up reel inside the printer. This is optional.
S e t t i n g t h e C u t M o d e
Set how the printer cuts tags. Purchase the optional 933 Cutter. The supply may shift as the cutter cuts and you may see a small disruption on the printed supply. This shift does not affect bar code quality. There is no cut button on the printer – select the appropriate cut mode for your application.
Since the cutter is 3.4 inches away from the printhead, printed tags may be left between the printhead and cutter. The cutter operates when the printer is running. If the printer is paused, the cutter stops cutting. The cutter also stops cutting whenever the cutter’s cover is opened.
Note: When cutting RFID supplies, enable tag saver.
Description of cut modes:
Cut Mode
Cut Before first tag in Batch?
Cut Betw een
Tags?
Cut After
Batch?
Printed tags left between printhead and cutter?
Disabled
No Cut
Cut Each Tag
Cut Each Batch
No No No
Cut Mode 3
Cut After Last
Tag
(Feeds strips)
Yes Yes No*
Cut Mode 4
No Cut Before
Cut Mode 5
Cut Last Strip
(Feeds strips)
No* Cut Modes 3 and 5 minimize the number of tags left between the printhead and the cutter.
Depending on the length of supply being cut, there may be one tag left between the printhead and the cutter.
Yes* The last tag in the batch is queued to be cut once it reaches the cutter; however, there may be printed tags left between the printhead and the cutter. The user must send another batch to feed the last tag out far enough to be cut.
Setting Supply Options 2-5
Recomme nde d Cutter Opera tion
Printhead
Density
203
203
203
203
300*
300*
300*
300*
With
RFID
Supply
With
Stacker
Attached Recommended Cut M odes
No
No
No
Yes
1, 2, 4 – Note: Cut Modes 3 and 5 m ay cause ribbon tearing
1, 2, 4 – Note: Cut Modes 3 and 5 m ay cause ribbon tearing
RFID is not supported with 203 dpi
RFID is not supported with 203 dpi
No
No
Yes
Yes
No
Yes
No
Yes
1, 2, 3, 4, 5
1, 2, 3, 4, 5
1, 2, 4
3, 5 – Note: Som e RFID supplies m ay curl and cause a jam
(with cut m ode 3). If this happens, use cut m ode 1.
* Contact Service to order replacement 300 dpi printheads (KST) for use with the cutter and
RFID supplies.
S e t t i n g t h e B ac kf e ed
Backfeed advances each printed label to the desired dispense position. Once that label is removed, the next label to be printed is backed up underneath the printhead.
Select To
Off
On
Disable backfeed.
Enable backfeed. The printer moves the supply backwards before printing. Use the Positioning menu to set the dispense position and the backfeed distance.
Setting Supply Options 2-6
A d j u s t i n g t h e P o si t i o n S et t i n g s
This menu includes selections to change the print, supply, margin, cut, dispense, and backfeed distance positions.
See the following graphic for a representation of the following adjustments: dispense position, backfeed distance, supply position, print position, and margin position.
Setting the Print Position
This function adjusts the image’s position on the supply in the feed direction. Adjust the print position if the print is too close to the top or bottom of the supply, or overtypes the pre-printed area. The adjustments are in dots where one dot equals 0.0049 inch.
Note: Changing this setting only affects new formats sent to the printer. Any formats previously saved into flash memory are not affected.
Select To
Decrease the setting. Moves the print down.
Increase the setting. Moves the print up.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting Supply Options 2-7
Setting the Supply P osition
This function adjusts the position of the supply relative to the index marks in the feed direction. Adjust the supply position to compensate for supply variation. The adjustments are in dots where one dot equals 0.0049 inch.
Note: Adjust the supply position only on initial printer setup. For format adjustments, change the print position. This option takes effect when you print the next label or tag. Changing supply position may also affect print position.
Select To
Decrease the setting. Moves the print down.
Increase the setting. Moves the print up.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting the Margin Position
This function adjusts where the format prints side to side on the supply. The adjustments are in dots where one dot equals 0.0049 inch.
The width of the print area depends on the supply size. The maximum width is four inches. W hen you move the image to the right or left on the supply, avoid moving the image too close to either edge, because it may not print.
P ri nt too far to th e l ef t P ri nt too far to th e ri ght
Note: Changing this setting only affects new formats sent to the printer. Any formats previously saved into flash memory are not affected.
Select To
Decrease the setting. Moves print to the left.
Increase the setting. Moves print to the right.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting Supply Options 2-8
Setting the Cut P osition
This function adjusts where the tag is cut. The printer adjusts the cut position according to the index marks on the supply. Aperture supplies may need adjustments. Increase to move the cut up; decrease to move the cut down.
Select To
Decrease the setting. Moves the cut down.
Increase the setting. Moves the cut up.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting the Dis pense Position
This function adjusts the amount to advance each label to allow for easy removal from the printer.
Select To
Decrease the setting. Moves the print down.
Increase the setting. Moves the print up.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting the Back feed Dis tance
The function adjusts the amount to move the label backwards at the start of each batch
(or label in on-demand mode). The backfeed distance should be equal to or less than the dispense position. If the backfeed distance is greater than the dispense position, the dispense position automatically changes to match the backfeed distance.
Select To
Decrease the setting. Moves the print down.
Increase the setting. Moves the print up.
Note: Press the left function button to change the amount (by 1, 10, or 100).
When tearing butt cut supplies, the backfeed distance must be 30 dots (0.15 inches) less than the dispense position. This causes a 30-dot non-print zone on the supply, but prevents exposed adhesive under the printhead.
Setting Supply Options 2-9
U s i n g B at ch S ep a r a t o r s
A batch separator is an extra tag printed in between batches with a pinstripe pattern. For continuous supply, the batch separator is always six inches long. The batch’s name prints on the batch separator.
Note: Changing this setting only affects new formats sent to the printer. Any formats previously saved into flash memory are not affected.
Select To
No
Yes
Disable batch separators.
Do not use batch separators with continuous (non-indexed) supply.
Enable batch separators.
Bat ch S epara tor
Long Enable double-length (two tags) batch separators.
U s i n g S ki p I n d ex
Skip index mode skips (or ignores) a sense mark and prints an image over multiple labels, if necessary. For example, if you have 4.0" long supplies loaded, but the image is
8.0" long, enable skip index mode to print the 8.0" long image on two labels. Use the skip index feature when you have a single format that contains two labels, such as a shelf label and a carton label.
The image length is determined by the format header. Refer to the Packet Reference
Manual for more information.
Note: When designing the format, make sure text or graphics do not print in the gap of label rolls. Do not use skip index with RFID supplies.
Select To
No
Yes
Disable skip index.
Enable skip index and print a format on two (multiple) labels.
Setting Supply Options 2-10
S e t t i n g t h e E r ro r A ct i o n
Sets how the printer recovers/responds to a bad RFID inlay. Selecting overstrike and continue 1x-5x sets the number of times the printer prints an overstrike pattern on consecutively bad labels before generating an error. The user must clear the error before operation can continue. The overstrike pattern prevents someone from using a bad label.
Note: Do not use the overstrike action with peel mode.
Select To
Normal Display the error. The error must be cleared before operation can continue. Press CANCEL to clear the error and continue printing. No overstrike pattern is printed.
Overstrike/Continue 1x
Overstrike/Continue 2x
Overstrike/Continue 3x
Overstrike/Continue 4x
Overstrike/Continue 5x
Attempt to reprint the label for one, two, three, four, or five consecutive tries. An overstrike pattern is printed each time the reprint fails. Printing is stopped after the selected number of overstrike patterns have printed. Press CANCEL to clear the error and continue printing. Do not use the overstrike label.
Example: Error action is set to overstrike/continue 3x:
♦
♦
♦
If the printer errors on the first label, an overstrike pattern is printed, but the printer attempts to reprint the image up to three times. If the third consecutive label also generates an error, an overstrike pattern is printed; however, the printer stops and the error message is displayed. The operator must resolve the error condition before printing continues.
In the above example, if the third label did NOT generate an error, the batch image is printed the consecutive error counter is reset the printer continues processing the batch.
S am pl e Overstri k e Label
Setting Supply Options 2-11
U s i n g Ro t at e I ma g e
Enabling this option rotates the printed image 180°. This is useful when the orientation of the supply does not match the format.
We recommend designing your formats as needed, so image rotation is not required.
Make sure the loaded supply matches the image length and width or the rotated image does not print correctly.
Select To
No Print the image without rotation.
Yes Rotate the image 180° before printing.
S e t t i n g t h e P r i n t Co n t ra s t
The contrast controls the darkness of the printing. Having the correct print contrast setting is important because it affects how well your bar codes scan and how long your printhead lasts. High contrast settings may require additional printhead cleaning, create bar code growth, and/or lead to reduced scanning.
Solid black print cannot exceed 30% of any given square inch of the supply.
Select To
Decrease the contrast. Lightens the print.
Increase the setting. Darkens the print.
Note: Press the left function button to change the amount (by 1, 10, or 100).
We recommend you check the bar code print quality. A bar code that is in spec has complete bars, clear spaces, and small alphanumeric characters look complete. An in spec bar code may not look as good as one that is too dark, but it has the highest scan rate.
Dark I N S P E C Li ght
Setting Supply Options 2-12
S E T T I N G C O M M U N I C AT I O N S
This chapter tells you how to set the serial and USB communication values. These values provide the link for normal online printing.
You need to set your Serial Comm values to match your computer's online communications.
The serial communication values are in the table below.
3
Option Choices Default
Baud rate
Word length
Stop bits
Parity
Flow control
1200/2400/4800/9600/19200/38400/
57600/115200
7/8
1/2
None/Odd/Even
None/Xon/Xoff/DTR/CTS
9600
8
1
None
DTR
Reset No/Yes No
Note:
The serial values on the printer must match those at the host.
Setting Communications 3-1
S e t t i n g t h e B au d R a t e
Baud rate is the speed, in bits per second, at which the printer sends and receives data.
Select To
1200
2400
4800
9600
19200
38400
57600
Communicate at 1200 bits per second.
Communicate at 2400 bits per second.
Communicate at 4800 bits per second.
Communicate at 9600 bits per second.
Communicate at 19200 bits per second.
Communicate at 38400 bits per second.
Communicate at 57600 bits per second.
115200 Communicate at 115200 bits per second.
S e t t i n g t h e W o rd L e n g t h
Word length specifies the number of data bits the printer uses to define a character.
Select To
7 Set the word length to seven.
1
2
8 Set the word length to eight.
S e t t i n g t h e S t o p Bi t s
A stop bit follows the data and parity bits to signal the end of a character.
Select To
Set the stop bit length to one.
Set the stop bit length to two.
Setting Communications 3-2
S e t t i n g t h e P a ri t y
Parity checks the validity of data entering the printer. The parity bit immediately follows the last data bit for a character. The computer adjusts the parity bit according to the parity so the data bits in the character, with the parity bit, form an odd or even number when summed.
Select To
None
Odd
Set the parity to none (no parity check).
Set the parity to odd.
Even Set the parity to even.
S e t t i n g t h e F l o w Co n t ro l
Data flow control is the method the printer uses to tell the computer whether it is ready to accept data.
Select To
None
Xon/Xoff
DTR
Set the flow control to none.
Set the flow control to XON/XOFF.
XON is 17; XOFF is 19.
Set flow control to DTR (Data Terminal Ready).
This is the most common setting. Use it for PC computers (unless you have
XON/XOFF software).
No
Yes
CTS Set flow control to CTS (Clear to Send).
R e s e t t i n g t o D ef a u l t V a l u e s
Use this setting to reset the printer’s communication values to the defaults listed at the beginning of this chapter.
Select To
Do not reset the serial communication values to their defaults.
Reset the serial communication values to their defaults.
Setting Communications 3-3
U s i n g U S B Co mm u n i c a t i o n s
Set the mode for the USB port.
The USB settings are in the table below.
Option Choices Default
Mode Printer/Virtual Serial Printer
Note: The printer reboots whenever the USB mode is changed.
Setting the Mode
Select To
Printer Using the Printer port, Microsoft® W indows® prompts the user for the printer driver, which is provided by our third party developers like
NiceLabel.
Virtual Serial Using the Virtual Serial port requires the ADTP1.inf file, which installs the printer as a virtual com port (for example COM4, COM5, etc.).
See “ Installing the Virtual Serial Driver ” for more information.
I n s t al l i n g t h e P ri n t e r D ri v er
Use the ADTP1 printer driver found on our Web site to print from Microsoft
Windows applications.
Note: The screens may appear differently on other Microsoft
Windows versions.
1. At the printer, set the USB Mode to Printer.
2. Download the latest drivers from our W eb site.
3. Click Run. If prompted to allow this software to run, click Run again. You see
4. Click Install NiceLabel Printer Drivers.
5. Click Next>.
Setting Communications 3-4
6. Select "I accept the terms in the license agreement" and click Next>.
7. Select Monarch as the Manufacturer.
8. Select Monarch ADTP1 (203dpi or 300dpi based on your printhead) as the Printer.
9. Click Next>.
10. Select the first available USB port, for example, USB001. Click Finish.
11. When the installation is complete, exit NiceLabel.
The printer is now ready to receive data through the USB port as a Virtual Printer Port.
Setting Communications 3-5
Installing the Virtual Serial Driver
These instructions are written for Microsoft® W indows® 7.
Note: The screens may appear differently on other Microsoft
Windows versions.
1. Download the file ADTP1.inf from our W eb site.
2. Save it to your hard drive.
3. Use a USB cable to connect the USB port on the printer to the USB port on your computer.
4. Turn on the printer. Set the USB Mode to Virtual Serial.
The computer acknowledges the new hardware. A message pops up, “the device driver was not successfully installed.”
5. Open Device Manager.
6. From Ports, USB port or Other devices, right click ADTP1 and select Update Driver
Software…
Setting Communications 3-6
7. Select Brow se my computer for driver software.
8. Click Brow se and navigate to the folder where you saved ADTP1.inf.
9. Click Next. The computer searches for the software. You may see
10. Select Install this driver softw are anyw ay.
A message appears that W indows has successfully updated your driver software.
11. Click Close to continue.
The updated driver appears in the Ports list as USB Communications Port (COM6) for example.
When connected via USB, the printer’s display includes the USB status icon:
Setting Communications 3-7
Setting Communications 3-8
S E T T I N G E T H E R N E T C O M M U N I C AT I O N S
The printer communicates on a 10baseT or 100baseTX wired Ethernet connection or on an 802.11 a/b/g/n network. See Chapter 5, “Setting W ireless Communications” for more information.
4
The printer’s display shows the network symbol (wired) when the printer is connected and ready to receive data. Additionally, the printer’s IP address is displayed when a connection is established.
The network options are listed in the table below.
Option Choices Default
MAC Address
IP Address
Subnet Mask
IP Gateway
View only xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
Boot Method
Wireless
Static/DHCP
See Chapter 5, “ Setting W ireless
Default Network Default Setting/Factory Default
V i ew i n g t h e M AC Ad d r e ss
None – preset value
192.0.192.0
0.0.0.0
0.0.0.0
Auto
N/A
N/A
The Media Access Control (MAC) Address is a hard-coded value that cannot be changed
(like a serial number). It consists of four 3-digit numeric fields, usually separated by periods.
Select To
MAC Address View the printer’s MAC Address.
Note: With version 1.6 or greater firmware, the Ethernet and wireless interfaces share the same MAC Address. W hen using DHCP, Ethernet and wireless will receive the same IP address from a DHCP server.
Setting Ethernet Communications 4-1
E n t e ri n g t h e I P A d d r e ss
The IP (Internet Protocol) address is a unique identifier for a device on a network. It consists of four 3-digit numeric fields, separated by periods. The printer has different IP addresses for wired vs. wireless communication.
If using the optional keyboard, enter the IP address you need using the numeric keys and press ENTER.
Select To
IP Address Change the printer’s IP address.
Press
or to highlight the position to change. Press CHANGE until you see the number you need. Press SET to save the setting or press
CANCEL to exit without saving.
Note: If you enter a series of digits greater than 255 for any segment of the IP address and press SET, the printer does not save the setting. Correct the setting, then press SET.
E n t e ri n g t h e S u b n e t M a s k
IP networks are divided using subnet masks. The subnet mask address determines where the IP address belongs in the network. It consists of four 3-digit numeric fields.
If using the optional keyboard, enter the subnet mask you need using the numeric keys and press ENTER.
Select To
Subnet Mask Change the printer’s subnet mask.
Press
or to highlight the position to change. Press CHANGE until you see the number you need. Press SET to save the setting or press
CANCEL to exit without saving.
Note: If you enter a series of digits greater than 255 for any segment of the IP address and press SET, the printer does not save the setting. Correct the setting, then press SET.
E n t e ri n g t h e I P G a t e w a y
The IP gateway (or router) allows connections (communications) between different subnets on a network. It consists of four 3-digit numeric fields.
If using the optional keyboard, enter the IP gateway you need using the numeric keys and press ENTER.
Select To
IP Gateway Change the printer’s IP gateway.
Press
or to highlight the position to change. Press CHANGE until you see the number you need. Press SET to save the setting or press
CANCEL to exit without saving.
Note: If you enter a series of digits greater than 255 for any segment of the IP address and press SET, the printer does not save the setting. Correct the setting, then press SET.
Setting Ethernet Communications 4-2
S e t t i n g t h e Bo o t M et h o d
The boot method sets the way the device receives its IP address.
Select To
Static
Use if your network uses fixed configuration. The IP address remains the same every time the device connects to the network.
DHCP
The network automatically assigns an IP address within a specified range to a device when it is first turned on. A device could have a different IP address every time it connects to the network.
Note: The 169.x.x.x IP address is a default address. If this IP address appears on your printer, it indicates the DHCP request failed.
D e f au l t N et w o r k
The default network option allows you to reset the Ethernet/wireless module.
Select To
Default
Setting
Any defaults set using the SET DEFAULT Telnet console command are restored.
Factory
Default
Reset the module to factory defaults.
See “ Factory Defaults ” for the list of default values.
When the module is reset to factory defaults, you must reconfigure all your specific network settings, including IP address, SSID, etc.
Note: Depending on your printer’s boot method, the IP address may be automatically assigned when you turn on the printer. The new IP address may not be the same as the previous one.
Setting Ethernet Communications 4-3
Factor y De faults
If you reset the Ethernet/W ireless module to factory defaults, the following values are restored. Some settings may stay the same, depending on your network
configuration.
Description Default
MAC Address
IP Address
Subnet Mask
IP Gateway
Signal Strength
SSID
Wireless Mode
Roam Threshold
Transmit Rate
Channel
Boot Method
Boot Tries
TCP/IP
This value is hard-coded and does not change
*
255.255.000.000
*
0
<none>
Infrastructure
6
1
1
DHCP
5
Enabled
TCP Port
LPD
Name
Encryption Mode
9100
Disabled
PXR_xxxxxx (xxxxxx = last six digits of the MAC address.)
Disabled
Authentication Type Open System
Authentication
Protocol
PAP
Regulatory Domain United States
* Ma y keep previous values based on network configuration.
Setting Ethernet Communications 4-4
S E T T I N G W I R E L E S S C O M M U N I C AT I O N S
5
Using the W ireless Menu, you can view the signal strength, set the Service Set
Identifier (SSID), wireless mode, roam threshold, transmit rate, and channel.
All nodes of a wireless network need to have the same settings to communicate with each other. If the printer is not communicating with the wireless module, the Network Menu options do not appear.
The printer’s display shows the network symbol (wired) or the antenna symbol
(wireless) when the printer is connected and ready to receive data. Additionally, the printer’s IP address is displayed when a connection is established.
Note: To configure the printer using MonarchNet2™, refer to the MonarchNet2
Operating Instructions on our W eb site.
With version 1.6 or greater firmware, the Ethernet and wireless interfaces share the same MAC Address. W hen using DHCP, Ethernet and wireless will receive the same IP address from a DHCP server.
The options are listed in the table below.
Option
Signal Strength
SSID
Wireless Mode
Roam Threshold
Transmit Rate
Channel
Choices
0 to 100 xxxxxxxxxxxxxx
Ad-Hoc/Infrastructure
1 to 15
1/2/5.5/11/12/18/24/36/48/54
1 to 11
Setting Wireless Communications 5-1
V i ew i n g t h e S i g n al S t r en g t h
The connection between the device and access point is shown as signal strength, which is a percentage from 0 to 100, where 0 is no connection and 100 is an excellent connection. A percentage below 30 indicates you may be experiencing interference or are close to being out of the access point’s range. W ith a percentage below 50, printing performance could be affected. If the signal strength is low, increase the number of retries. To improve the signal strength, try moving the printer closer to the access point and away from other radio devices such as Bluetooth
wireless devices, microwave ovens, or 2.4-gigahertz cordless phones.
Select To
Signal Strength View the printer’s signal strength.
E n t e ri n g t h e S S I D
The Service Set Identifier (SSID) is a unique identifier that must match for all nodes on a sub network to communicate with each other. It consists of up to 32 characters (any printable character, including spaces). If using the space character, it must be enclosed in quotation marks.
Note: The SSID is case-sensitive. If using the optional keyboard, enter the SSID you need using the numeric keys and press Enter.
Select To
SSID Change the printer’s SSID.
To highlight the position to change, press
or until the cursor is below the character to change.
Press CHANGE until the character you need appears.
Press SET to save each position. The cursor moves to the next position. Press SET when finished or press CANCEL to exit without saving.
Note: Hold CHANGE to scroll quickly through the characters or press
CHANGE once to scroll one character at a time.
To clear the SSID, scroll to the end of the field, press and hold
and at the same time for a few seconds, then release. If you are in the middle of the field, press and hold
and at the same time for a few seconds, then release, to clear any characters to the right of the cursor.
Setting Wireless Communications 5-2
W i r el e s s M o d e
The wireless mode sets how you communicate with your wireless network.
Select To
Adhoc
Use ad-hoc mode (you do not need an access point). This is also called peer-to-peer (point-to-point) communications, so as long as the devices are in range, they connect/communicate with each other.
Infrastructure
Use infrastructure mode (requires an access point to communicate).
Note: If communicating in a mixed environment where both ad-hoc and infrastructure mode are used, make sure the SSIDs are unique in both modes.
R o am T h r e sh o l d
Sets the roaming threshold. W henever the printer’s signal strength gets below this value, the printer connects to another access point in range with better signal strength. This prevents excessive roaming between access points if the printer is located near two access points.
The range is 1-15. 1 gives no preference to the currently connected access point.
15 gives the maximum preference to the currently connected access point.
Select To
1 - 3
Sets the roam threshold to 11 decibels. When the printer’s signal strength gets below 11 decibels, it connects to another access point in range with better signal strength.
4 - 6
7 - 10
Sets the roam threshold to 12 decibels.
Sets the roam threshold to 13 decibels.
11 - 13
Sets the roam threshold to 14 decibels.
14 - 15
Sets the roam threshold to 15 decibels.
Note: This setting is helpful when the printer is on a Mobile W orkstation.
Setting Wireless Communications 5-3
12
18
24
36
1
2
5.5
11
48
54
T r an s mi t R a t e ( A d - Ho c O n l y)
The transmit rate sets the maximum speed at which the devices communicate with each other on the network. The speeds are in Mbps (megabits per second). The transmit rate is negotiated with the access point and this setting may be ignored. Use this setting in ad-hoc mode only.
Select To
Communicates at 1 Mbps.
Communicates at 2 Mbps.
Communicates at 5.5 Mbps.
Communicates at 11 Mbps.
Communicates at 12 Mbps.
Communicates at 18 Mbps.
Communicates at 24 Mbps.
Communicates at 36 Mbps.
Communicates at 48 Mbps.
Communicates at 54 Mbps.
Setting Wireless Communications 5-4
C h an n el ( Ad - Ho c O n l y)
This option selects the channel on which your network devices communicate. All devices must be on the same channel to communicate. Other radio devices such as Bluetooth
wireless devices, microwave ovens, or 2.4-gigahertz cordless phones may operate on the same channel as your network. Channels 1-11 are available. Use the channel for ad-hoc mode. In infrastructure mode, the channel is negotiated with the access point and this setting is ignored. Use this setting in ad-hoc mode only.
Select To
7
8
5
6
3
4
1
2
Use channel 1.
Use channel 2.
Use channel 3.
Use channel 4.
Use channel 5.
Use channel 6.
Use channel 7.
Use channel 8.
9
Use channel 9.
10
Use channel 10.
11
Use channel 11.
Note: Make sure all network devices are set to the same channel.
If you have problems connecting to your network, change the channel to at least three channels lower or higher than any other wireless networks within range.
Setting Wireless Communications 5-5
Setting Wireless Communications 5-6
S E T T I N G D E F A U LT S
This chapter explains how to select the monetary sign, secondary sign, decimal places, slashed zero, power-up mode, prompt set, imaging errors, ignore configuration packets, error retry, and adjust the image length. This chapter also explains how to format flash, check the available flash memory, and pack flash memory.
6
You can set your printer configurations to fit your daily operation, using either the offline menus or the online configuration option. After an option is selected in the online configuration or offline Setup Menu, the option is saved when the printer is turned off.
The monetary formatting options are in the table below.
Option Choices Default
Monetary sign
Secondary Sign
Decimal Places
Slashed Zero
Power-up Mode
Prompt Set
None, $ Dollar, £ Pound, ¥ Yen, Deutsche Mark, F
Franc, P Peseta, L. Lira, Kr Krona, Markka, Shilling,
Rs Rupee, Ruble/Rubel, W on, Baht, ¥ Yuan, € Euro
No/Yes
0/1/2/3
No/Yes
Online/Offline
English, Français, Deutsch, Español-ES,
ニホンゴ
,
Português, Italiano, Svenska, Español-MX, Dansk,
Nederlands, Polski, Türkçe,
简体中文
, Français-CA
$ Dollar
No
2
No
Online
English
Numeric Format Default, Arabic-Indic, Eastern Arabic
Flash Storage Disabled/Enabled
No Image Error
Ignore Config
Disabled/Enabled
Disabled/Enabled
Error Retry
Adjust Length
Sleep Time
LCD Contrast
Disabled/Enabled
-30 to 30
0 to 240
1 to 9
Default
Disabled
Disabled
Disabled
Enabled
0
60
3
The monetary sign, secondary sign, and decimal places options are used in conjunction with option 42. Refer to the Packet Reference Manual for more information.
Note:
The settings for monetary sign, secondary sign, slashed zero, and decimal places apply when a format is downloaded. Changing the settings does not affect batches already in the printer.
You can also select None if you do not want a monetary sign to print in price fields.
Setting Defaults 6-1
S e t t i n g t h e M o n e t a r y S i g n
The printer contains 16 different currency symbols.
Select To
None
Dollar
Does not print a monetary sign.
Print the $ sign.
Pound
Yen
Deutsche Mark
Print the £ sign.
Print the ¥ sign.
Franc
Peseta
Lira
Krona
Markka
Print the sign.
Print the F sign.
Print the P sign.
Print the L. sign.
Print the Kr sign.
Print the sign.
Shilling
Rupee
Ruble/Rubel
Print the sign.
Print the Rs sign.
Print the sign.
Won
Print the sign.
Baht
Yuan
Print the sign.
Print the ¥ sign.
Euro Print the € sign.
S e t t i n g t h e S e co n d a r y S i g n
If you select the dollar as the monetary sign, you can print amounts less than $1.00 either by using a dollar sign and decimal ($0.30) or by using a cent sign (30¢).
Select To
No Do not print a secondary monetary sign. prices under $1.00 will print like this: $ .45
Yes Print a secondary monetary sign. prices under $1.00 will print like this: 45¢
Note: The same option applies to the appropriate secondary sign for monetary signs other than the dollar.
Setting Defaults 6-2
S e t t i n g t h e Nu mb e r o f D e ci ma l P l a c e s
Set the printer for 0, 1, 2, or 3 places after the decimal in a price field. In dollar currency, you might print prices like this: $24.00 (2 decimal places) or like this: $24 (0 decimal places).
Select To
0
1
Do not use decimal places. prices print as whole numbers: $20
Print one place after the decimal. prices print like this: $20.5
2 Print two places after the decimal. prices print like this: $20.50
3 Print three places after the decimal. prices print like this: $20.500
S e t t i n g t h e S l ash ed Z e ro Ap p e a ra n c e
The slashed zero feature lets you select how you want the zero character printed; either without a slash, 0 or, with a slash,
Ø.
Standard or reduced fonts print the slashed zero character (
Ø). Bold and OCR fonts print the standard zero (0) only. The slashed zero selection does not take effect until the format is sent to the printer again. If you change the way zero prints, you must resend your formats.
Select To
No Do not print zeroes with a slash.
Yes Prints zeroes with a slash (
Ø).
S e t t i n g t h e P o w e r - Up M o d e
Power-up mode lets you decide how your printer starts each time you turn it on:
♦
♦
♦
Ready to receive data and start printing (online mode).
Operator can select a format to print (offline mode).
Operator can enter data for a selected format using the 939i Keyboard or USB keypad
(offline mode). For offline data entry information, see the 939i Keyboard’s Operating
Instructions.
Select To
Online
Offline
When the printer is turned on, you see “Ready.”
When the printer is turned on, you see Data Entry mode. Make sure formats are loaded into flash memory and a keyboard is connected if you need to enter data.
Setting Defaults 6-3
S e t t i n g t h e L an g u ag e
The printer can display prompts in different languages: English, Français, Deutsch,
Español-ES,
日本語
, Português, Italiano, Svenska, Español-MX, Dansk, Nederlands,
Polski, Türkçe,
简体中文
, and Français-CA.
Note: Some prompts may remain in English, even if you select a different language.
Select To
English
Français
Displays prompts in English.
Displays prompts in French.
Deutsch
Español-ES
日本語
Displays prompts in German.
Displays prompts in European Spanish.
Displays prompts in Japanese.
Displays prompts in Portuguese. Português
Italiano
Svenska
Español-MX
Displays prompts in Italian.
Displays prompts in Swedish.
Displays prompts in Latin American Spanish.
Displays prompts in Danish. Dansk
Nederlands
Polski
Türkçe
简体中文
Displays prompts in Dutch.
Displays prompts in Polish.
Displays prompts in Turkish.
Displays prompts in Simplified Chinese.
Français-CA Displays prompts in Canadian French.
S e t t i n g t h e Nu me r i c F o r m at
Numeric format determines how numeric values appear in your printed data.
Select To
Default
Arabic-Indic
Latin numerals print in Latin; Arabic text prints in Arabic.
Latin numerals print in Arabic; Arabic text prints in Arabic.
Eastern-Arabic Latin numerals print in Arabic; Arabic text prints in Arabic.
Examples
Latin Characters: 95% cotton
Latin Numerals with Arabic Characters:
% 95
ﺏﻁﻗ
Arabic Numerals with Arabic Characters:
Arabic-Indic:
Eastern-Arabic:
Setting Defaults 6-4
U s i n g F l a sh S t o r a g e
Packets (formats, fonts, graphics) stored in flash memory are saved when the printer is turned off.
Note: You must format flash memory before enabling this option. Formatting flash memory is only required once during initial printer setup.
Select To
Disabled Does not allow flash storage.
Enabled Allows flash storage for formats, fonts, and graphics.
S e t t i n g t h e I m ag e E r ro r M o d e
Image errors occur when there is a problem producing a complete label. Press ESCAPE to clear an image error.
Select To
Disabled If a format does not print as expected, an error message appears on the display.
Enabled If a format does not print as expected, no error message appears and the format prints as is.
For example, bar codes require a non-print zone; if a bar code is placed too close to the edge of the label, no error is reported and the bar code may not scan properly.
Image errors include:
600 unable to image batch
601 problem during imaging
603 missing batch
611 invalid font, bar code or density
612 missing batch data
614
615
618
620
621 portion of field off label invalid PDF417 bar code data invalid font size missing font data invalid downloaded font
613 reference point off label 622 not enough font memory
Note: Error 616 (bar code dot shifting failed) is always reported.
Setting Defaults 6-5
S e t t i n g t h e Co n f i g u r a t i o n P a c k et M o d e
The printer can respond to or ignore all online configuration packets.
Note: We recommend changing your host’s data stream, but if that is not possible, enable this option.
Use caution if ignoring online configuration packets, because the printer may need the configuration for proper operation!
Select To
Disabled The printer responds to all online configuration packets.
Enabled The printer ignores all online configuration packets. This is useful when you cannot change your host’s data or when you want the printer to operate as specified through the printer’s menu.
S e t t i n g t h e E r ro r R et r y M o d e
The printer either reprints the job or discards/cancels the job after a supply error is cleared. Depending on your environment, you may not want jobs reprinted.
Select To
Disabled
Enabled
The printer discards the job that was in process and does not reprint it.
The printer reprints the job that was in process when the error occurred.
Setting Defaults 6-6
A d j u s t i n g t h e I ma g e L en g t h
Using this setting requires continuous (non-indexed) supply. The printer ignores this setting (does not error) when using other supply types.
This setting increases or decreases the image length based on the percentage entered.
Values are in tenths of a percent.
Note: If a print image is defined close to the label’s edge and adjust image length is set
to a negative value, the printed image may not be complete. Some of the image may be lost. Verify your printed image is complete.
Examples
Format A is 10.0 inches long (as defined in the format header).
Image Length is +20
Format A prints 10.20 inches long.
Format B is 6 inches long (as defined in the format header).
Image Length is -30
Format B prints 5.82 inches long.
Note: Refer to the Packet Reference Manual for more information about defining the format header.
Select To
Decrease the setting. Reduces the image length by the entered percentage.
Increase the setting. Increases the image length by the entered percentage.
Note: Press the left function button to change the amount (by 1 or 10).
S e t t i n g t h e S l eep D el a y
When the printer is idle for a selected period of time, it goes into sleep mode to conserve power. Adjust the sleep delay setting from 1 minute to 240 minutes. The default setting is
60 minutes. The printer wakes from sleep mode when it receives a print job, a button is pressed, or the printhead is opened/closed.
Select To
Decrease the inactivity time before the printer goes into sleep mode.
Increase the inactivity time before the printer goes into sleep mode.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting Defaults 6-7
S e t t i n g t h e L C D C o n t r a s t
With version 1.9 or greater firmware, adjust the contrast (brightness) of the LCD. The range is 1 to 9. The default is 3.
Select To
Decrease the LCD contrast (make the display lighter).
Increase the LCD contrast (make the display darker).
U s i n g F l a sh M em o r y
Use these basic guidelines when storing files in your printer's flash memory.
♦
Your printer has volatile RAM (packets deleted when the printer is off) and flash memory (packets saved when the printer is off).
♦
Flash memory must be formatted before any packets can be saved. See "
Flash Memory " for more information.
♦
Formats, graphics, and check digits can be saved in flash (a copy is automatically placed in RAM). Any packets saved in flash cannot exceed the memory available in
RAM.
♦
There is not a 1-to-1 ratio between the RAM memory (formats, graphics, and check digits) in your printer and the memory in your PC. For example, a file that is 5K in
Windows may require 15-20K to store in your printer.
♦
Use temporary storage for graphics that are only used once or twice. However, if you have a logo that is used on multiple formats, save the graphic in flash.
♦
Each line in a packet requires the same amount of memory. The smaller the format, the less memory required to save it.
The flash memory options are in the table below.
Option
Format Flash
Unused Flash
Pack Flash
Choices
No/Yes
NA
No/Yes
Default
No
NA
No
Setting Defaults 6-8
Forma tting Flas h Memory
Before storing packets in flash memory, downloading a script, or updating the printer's firmware, you must format the flash memory. Formatting flash memory is only
required once during initial printer setup.
Select To
No Does not format flash memory.
Yes Formats flash memory.
The printer's flash memory is cleared and reformatted. This process may
take several minutes. The printer reboots automatically after formatting flash memory
Any scripts, downloaded fonts, formats, or graphics saved in the printer's flash memory are deleted and must be resent to the printer.
View ing Available Flash Memory
If you receive errors when downloading a script or other packets, make sure you have enough flash memory available.
Select To
Unused Flash View the amount of available flash memory in bytes. Divide this number by 1024 to get the number of available kilobytes. Make sure your font or
ADK script files do not exceed this amount.
Packing Flash Me mor y
Packing flash memory permanently removes any deleted files from memory.
Select To
No
Yes
Does not pack flash memory.
Packs flash memory.
Removes any deleted files from memory. Periodically select this option to
"clean up" the printer's memory.
Setting Defaults 6-9
U s i n g a U S B T h u m b D r i v e
Using a USB thumb drive, you can update
printerbootloader (r46*.bin) printer firmware (a46*.bin)
RFID firmware (a84*.bin)
RFID inlay database (d46ES*.db)
Note: The USB thumb drive must be
WIN32 format.
Only a qualified Service Representative may update the bootloader, printer’s firmware, and RFID firmware.
Updating the RFID Inlay Database
The printer contains an RFID inlay database (d46ESxx.db). The RFID database is included with the printer’s firmware and does not need to be flashed separately.
However, new inlays may be qualified in between firmware releases. Only inlays qualified for use in the ADTP1 printer are included. The xx in the filename indicates the revision level of the database.
To update the RFID Database:
1. Create an ADTP folder on your thumb drive.
2. Download the necessary file (d46ESxx.db) from our website.
3. Save the file to the ADTP folder on your thumb drive.
4. Turn on the printer. When you see “Ready”, insert the thumb drive into the USB port.
5. Press MENU and use or to select the Setup menu, USB Drive.
6. Press ENTER and use or and select the RFID Database file.
7. Press SELECT.
Setting Defaults 6-10
8. Press OK. The progress is shown on the display:
USB Drive Troubleshooting Information
You may receive these messages while using a USB thumb drive.
Problem Action
Insert the thumb drive into a USB port.
Files on the thumb drive must be saved into a folder named
ADTP, not ADTP1 or the root.
S e t t i n g t h e C l o c k ( O p t i o n a l )
The EF version (extended features) printer contains a real-time clock. Set the clock during initial printer setup.
The printer keeps track of the date and time even when the printer is turned off. The clock does not adjust for daylights saving time.
The clock options are in the table below.
Option Choices
Day of Month 1 to 31
Default
0
0
1
1
0
Setting Defaults 6-11
Setting the Hour
Set the clock’s time for hours. The clock operates on 24-hour time.
Select To
0 - 12 Sets the hour to the specified time (AM).
13 - 23 Sets the hour to the specified time (PM).
For example, 16 is 4:00 PM.
Setting the Minute
Set the clock’s time in minutes.
Select To
0 - 59 Sets the time in minutes to the specified time.
Setting the Da y of the Month
Set the clock’s day of the month.
Select To
1 - 31 Sets the day of the month to the specified number.
Setting the Month
7
8
9
10
11
12
3
4
5
6
Set the clock’s month.
Select To
1
2
Sets the clock to January.
Sets the clock to February.
Sets the clock to March.
Sets the clock to April.
Sets the clock to May.
Sets the clock to June.
Sets the clock to July.
Sets the clock to August.
Sets the clock to September.
Sets the clock to October.
Sets the clock to November.
Sets the clock to December.
Setting Defaults 6-12
Setting the Yea r
Set the clock’s two-digit year.
Select To
00 to 99 Sets the year to the specified number.
For example, 14 indicates year 2014.
S e l ec t i n g t h e I n t e r p r et e r
The printer includes four Interpreter options.
Note: The printer reboots automatically after selecting an interpreter. This process may take several seconds.
When you see “Ready,” the selected interpreter appears in the upper left-hand corner of the display.
The interpreter options are in the table below.
Option Choices Default
MPCL/MLI/XML MCPL Interpreter
Select To
MPCL
MLI
Use the MPCL interpreter. Refer to the Packet Reference Manual on our
Web site for more information.
Use the MLI interpreter. Refer to the MLI Quick Reference on our W eb site for more information. When you print test labels, the model number appears as ADTP-1MLI.
XML Use the XML interpreter. Refer to the XML Quick Reference on our W eb site for more information. When you print test labels, the model number appears as ADTP-1X.
Setting Defaults 6-13
Setting Defaults 6-14
U S I N G S C R I P T S
This chapter explains how to load, enable, and delete scripts. You can also enable status polling and immediate commands.
Using the Scripts menu requires custom software. Scripts can print data streams written for other printers or define a lookup table. Contact us to create a custom script for your printer.
7
You can limit access to this menu to prevent changes.
The script options are in the following table:
Option Choices Default
Load Script
Enable Script
NA
No/Yes
Script Info
Delete Script
Status Polling
NA
No/Yes
Disable/Enable
Immediate Commands Disable/Enable
I n i t i a l S c ri p t S t ar t u p P ro c ed u r e s
NA
No
NA
No
Disable
Disable
Before you can start using a script, check the following items:
♦
Check to see if a script is already in the printer. See "
continue.
Viewing Script Information " to
♦
Format flash memory, if needed. See "
more information.
Formatting Flash Memory " in Chapter 6 for
♦
Download a script to the printer, if needed. See " Downloading a Script " to continue.
Using Scripts 7-1
V i ew i n g S c ri p t I n f o rm a t i o n
You can view information about a loaded script.
Select To
Script Info View the information about the loaded script.
If a script is not loaded, you see "No script loaded."
If a script is loaded, you see the script name and version number.
Note:
If a script is already loaded, see " Enabling a Script ," to continue. If you need to
download a script, see " Formatting Flash Memory " in Chapter 6.
D o w n l o ad i n g a S c r i p t
Follow these instructions to download a script from the command prompt. Set the communication parameters using the MODE command. Then, prepare the printer to accept a script.
Select To
Load Script Prepares the printer to accept a script file.
Note: Only one script can be loaded in the printer at a time.
Send the script file to the printer.
When downloading a script, if you receive an error:
♦
Check the available flash memory. See "
6 for more information.
Viewing Available Flash Memory " in Chapter
♦
information.
Formatting Flash Memory " in Chapter 6 for more
After downloading a script, if the script does not appear to be loaded, try formatting flash memory and download the script again.
E n a b l i n g a S c ri p t
The script must be enabled before you can use it.
Select To
No Does not enable the script. (Stop the script).
Yes Start the script. W hen you turn the printer off and back on, the script automatically starts.
When you see “Ready,” the word “Script” appears in the upper left-hand corner of the display.
Note: When a script is not loaded, this message appears:
Using Scripts 7-2
D e l et i n g a S cr i p t
You can delete a script from the printer's memory.
Select To
No Does not delete the script.
Yes Deletes the script.
Note: The flash memory used by the script is not available for other scripts or fonts until the flash memory is reformatted. However, when you format flash memory, you must resend the script and any downloaded fonts to the printer.
E n a b l i n g S t at u s P o l l i n g
Status polling allows you to obtain information about the readiness of the printer and the current (or last received) print job.
Select To
Disable Do not use status polling.
Enable Use status polling.
U s i n g I m m ed i a t e Co m ma n d s
You can use immediate commands to reset the printer or cancel and repeat batches.
Immediate commands are turned on or off through an MPCL packet. Refer to the Packet
Reference Manual (available on our W eb site) for more information about immediate commands and control characters.
Use this option to set whether the ADK script processes or ignores an immediate command control character.
Select To
Disable
Enable
ADK script ignores an immediate command control character.
Instead, the immediate command control character and immediate command are treated as data.
ADK script processes an immediate command control character and performs the requested immediate command.
Using Scripts 7-3
Using Scripts 7-4
S E T T I N G R F I D O P T I O N S
The RFID printer has been engineered to encode (program) an RFID (Radio
Frequency Identification) inlay while printing. RFID inlays contain an embedded programmable microchip and an antenna. The printer supports EPC Class-1 Generation-
2 UHF (C1Gen2) protocol encoding following the EPC™ Radio-Frequency Identity
8
Protocols Class 1 Generation 2 UHF RFID Protocol for Communications at 860-960MHz
Standards (GS1 EPCglobal™ Specification for RFID Air Interface). To create a format with an RFID data field and program RFID data, refer to the Packet Reference Manual.
An RFID printer has an antenna to program RFID inlays. Two antenna modules are available – one for FCC and one for ETSI frequencies. The antenna module type prints
on the RFID configuration label. See “ Printing a Test Label ” for more information.
Note: The bar code verifier cannot be used with RFID.
An optional external verifier (reader) is available to verify the data within a programmed
RFID inlay. The antenna is located within the supply path. The optional external verifier is located where the supply exits the printer. Peel mode or liner take-up is not available with optional external RFID verifier.
An t enna
Opti onal
E xternal
V eri fi er
The RFID printer operates in one of two modes:
♦ non-stop encode mode
In non-stop encode mode, the printer does not pause (or stop) while encoding the RFID inlay. Non-stop encode is
useful with minimum “pitch” supplies. See “ W hat is Pitch ”
for more information.
♦ stop-to-encode mode
In stop-to-encode mode, the printer pauses (or stops) while encoding the RFID inlay.
A b o u t RF I D S u p p l i es
RFID supplies can be damaged by static electricity. Ground yourself by touching metal, such as the printer’s metal base, before handling the RFID supplies.
Note:
Printing over the RFID inlay causes printing irregularity and may impact bar
code print quality.
Do not use skip index with RFID supplies.
Setting RFID Options 8-1
What is Pitch?
Pitch is the length of the label measured from the leading edge of one label to the leading edge of the next label as shown. Pitch includes the gap between die cut labels.
When using a short supply length, enable singulate mode to prevent adjacency issues.
♦ Die cut supplies:
Measure from the leading edge of one label to the leading edge of the next label.
♦ Black mark supplies: Measure from the top of one black mark to the top of the next black mark.
♦ Aperture supplies:
Measure from the top of one aperture hole to the top of the next aperture hole.
Note: The leading edge is the edge of the label that exits the printer first; regardless of how the format is designed on the label.
Di e Cut Bl ack M ark
M easure thi s di stanc e
Do not pri nt i n the gap !
M easure thi s di stanc e
Ap e rtu re
M easure thi s di stanc e
Setting RFID Options 8-2
G e t t i n g S t a rt ed W i t h RF I D
The printer’s RFID menu has two options: Easy Setup and Advanced Setup. The preferred methods of RFID setup are:
1) Using the Easy Setup Menu to quickly configure the printer.
2) Using the Monarch® RFID Printer Setup Utility to configure the printer’s read/write powers, positional settings, etc. Find this Web-based utility at http://rbis.averydennison.com/en/home/products/printers/tabletop/ADTP1-productsupport-pc.html
Note:
The advanced setup menu is for advanced users. See “ Using the Advanced
Setup Menu ” for more information.
U s i n g t h e E as y S e t u p M en u
With Easy Setup, enter two parameters for RFID to quickly start encoding RFID inlays.
The two parameters to enter may be printed on the RFID supply roll core’s label: inlay type and inlay position (in millimeters). Easy Setup is only for use with non-stop
encoding.
The Easy Setup options include:
Option Choices Default
Select Inlay various N/A
Inlay Pos [mm] 0-200 0
The printer contains a RFID inlay database (d46ESxx.db). If the database is not already installed in your printer, download it from the RFID Printer Setup Utility: http://rbis.averydennison.com/en/home/products/printers/tabletop/ADTP1-productsupport-pc.html
Check the RFID Printer Setup Utility for database updates and downloads if your inlay type is not listed. Only inlays qualified for use in the ADTP1 printer are included in the
database. See “ Updating the RFID Inlay Database ” for more information
Once the inlay and inlay position are entered, the printer uses its RFID inlay database to configure the:
♦ correct inlay read/write power levels
♦ inlay position settings
♦ singulate mode and TID position (if necessary)
♦ speed (decrease as necessary)
Once a batch is sent to the printer, the printer begins encoding and printing.
More information about the RFID values the printer automatically sets in Easy Setup can
be found in Using the Advanced Setup Menu .
Setting RFID Options 8-3
Selecting the Inlay
This option only appears in the Easy Setup menu. You must know the name of the RFID inlay being used. Names and pictures of the approved inlays are in the RFID Printer
Setup Utility. Load RFID supply before you enter values in the Easy Setup menu.
The printer contains a list of approved inlays. If your RFID inlay is not listed, it may not be qualified for use or update the printer’s
RFID inlay database (d46ESxx.db). See
“ Updating the RFID Inlay Database ” for more
information. The RFID Printer Setup Utility has database updates and downloads.
1. The inlay’s name may be on the supply core’s label; otherwise, look at pictures of the approved inlays in the RFID Printer Setup Utility. For example, AD-383U7
GNC.
2. Press or to select your inlay, then press SET. “Custom” appears as the selected inlay’s name if the print speed is increased or any RFID settings are changed.
Entering the Inla y Position
This option only appears in the Easy Setup menu. The inlay position must be entered in millimeters. Measure the inlay position as shown to the nearest whole millimeter. For example, if the measured distance is 7.25mm, enter 7mm.
M easure thi s di stanc e
Note: Press the left function button to change the amount (by 1, 10, or 100).
1. The inlay’s position (in millimeters) may be on the supply core’s label. For example, enter 002 as 2.
2. Enter the inlay’s position, then press SET.
Select
To
Decrease the inlay distance.
Increase the inlay distance.
The printer may prompt to calibrate when exiting the
Easy Setup menu. Press START to calibrate or STOP to cancel.
The calibration prompt appears when the inlay type or the inlay distance changes.
Setting RFID Options 8-4
U s i n g t h e Ad v an c e d S et u p M en u
The preferred methods of RFID setup are:
1) Using the Easy Setup Menu to quickly configure the printer.
2) Using the Monarch® RFID Printer Setup Utility to configure the printer’s read/write powers, positional settings, etc. Find this Web-based utility at http://rbis.averydennison.com/en/home/products/printers/tabletop/ADTP1-productsupport-pc.html
The advanced setup menu is for advanced users. Changing settings in the advanced menu is not typically recommended.
Note: Adjust these settings only if errors are received when using values from Easy
Setup or the RFID Printer Setup Utility. Adjusting these settings may cause undesired results.
The advanced setup menu changes whether non-stop encode mode or stop-to-encode mode is selected.
The Advanced Setup options include:
Option Choices Default Non-Stop
Encode
Stop-to-
Encode
Stop-To-Encode
Mode
Singulate Mode
Write Power
Read Power
Encode Position
Tag Saver
Yes/No
Yes/No
-15 to 23
-15 to 23
0 to 2000
Yes/No
First TID Position 0 to 2000
Start Encode Position 10 to 2000
Encode Zone
Tag Verify
50 to 2000
None/Internal/
External/Both
No
No
-15
-15
0
No
0
100
200
None
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Verify Power
Tag Verify Position
Retry Encode
-15 to 23
10 to 2000
-15
100
Enable/Disable Enable
X
X
X
X
X
X
Clear Data Yes/No No X X
Use the RFID Printer Setup Utility to calculate the required positional settings.
Setting RFID Options 8-5
Setting S top-To-E ncode Mode
This option only appears in the Advanced Setup menu. The printer operates in non-stop encode or stop-to-encode mode. The default is non-stop encode.
Select To
Yes Use stop-to-encode mode. The printer pauses (or stops) while encoding the
RFID inlay.
The printer feeds supply, stops to encode the inlay, then prints the image.
Backfeeding may occur to properly position an inlay over the antenna. An inlay is encoded then the label is imaged/printed.
Stop-to-encode mode may yield faster throughput with specifically configured supply.
No Enable non-stop encoding. The printer does not pause (or stop) while encoding the RFID inlay.
Encoding and printing is done at the same time.
Non-stop encoding is required for minimum pitch supplies. See “ What is
Performance Cons iderations w ith RFID
The printer has two RFID modes of operation: stop-to-encode and non-stop encode:
Stop-to-encode mode Non-stop encode mode
♦
The printer pauses (or stops) while encoding the RFID inlay.
♦
The amount of programmable EPC data, user memory, access password, and lock code data varies by RFID chip.
♦
The printer errors if it cannot program all the RFID data within the allotted time.
♦
Stop-to-encode mode must be used for serialized EPC data. Refer to the
Packet Reference Manual for more information.
♦
The printer does not pause (or stop) while encoding the RFID inlay.
♦
Some RFID chips encode faster than others.
♦
The faster the print speed, the less time the printer has to encode data.
♦
The amount of programmable EPC data, user memory, access password, and lock code data varies by print
speed and RFID chip.
♦
The printer errors if it cannot program all the RFID data while the inlay is within the encode zone.
Setting RFID Options 8-6
Enabling Singulate Mode
This option only appears in the Advanced Setup menu. The default is no.
When singulate mode is enabled, set the first TID position. See “ Setting the First TID
Position ” for more information.
Select To
Yes Enable singulate mode. The printer uses low power to read the unique
TID field of the RFID inlay over the printer’s antenna. Then the printer uses this TID number to program (with a higher write power) only that specific inlay.
Use singulate mode to avoid adjacency issues with minimum pitch supplies. Adjacency issues occur when leading or trailing RFID inlays are encoded instead of the inlay over the antenna.
Note: While singulate mode is more reliable, it may decrease throughput.
No Disable singulate mode. The printer does not use the TID field to program a specific inlay.
Setting the Write Pow er
This option only appears in the Advanced Setup menu. The write power setting increases the strength of the RF Field emitted by the printer’s antenna. Use this power to encode
(program) the RFID inlay. The range is -15 to 23. The default is -15.
Use the RFID Printer Setup Utility to determine the write power then enter the value at the printer.
Select To
Decrease the setting.
Increase the setting. The higher the value, the greater the power of the
RF Field. If the W rite power setting is too high, you may change the data that was programmed into adjacent RFID inlays.
Note: Press the left function button to change the amount (by 1 or 10).
Setting RFID Options 8-7
Setting the Read Pow er
This option only appears in the Advanced Setup menu. The read power setting increases the strength of the RF Field emitted by the printer’s antenna. Use this power to read tags in singulate mode. The range is -15 to 23. The default is -15.
Use the RFID Printer Setup Utility to determine the read power then enter the value at the printer.
Select To
Decrease the setting. If the read power setting is too low, the RFID inlay in the RF field may not be read.
Increase the setting. If the read power setting is too high, adjacent
RFID inlays may be read.
Note: Press the left function button to change the amount (by 1 or 10).
Setting the Encode Position
This option only appears in the Advanced Setup menu when using stop-to-encode mode.
The encode position is measured from the leading edge of the supply to the best programming position within the inlay. The encode position is different for each type of inlay. The range is 0 to 2000. 0 is the default, which indicates the printer does not have to reposition the inlay.
Note: Set this position only when using stop-to-encode mode.
When using a 0 encode position, the printer encodes when the label is at the defined top-of-form position – no extra supply movement is required.
When using a non-zero encode position, the printer automatically backfeeds between labels, thereby decreasing throughput.
E ncode P osi ti on
Tr ai l i ng E dge
0, 0 poi nt
Leadi ng E dge
Use the RFID Printer Setup Utility to determine the encode position then enter the value at the printer.
Select To
Decrease the setting.
Increase the setting.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting RFID Options 8-8
Enabling Ta g Sa ver
This option only appears in the Advanced Setup menu. Not all RFID supplies support tag saver. The default is no.
Select To
Yes Enable tag saver. The printer moves the first tag in the batch backwards to the proper position before encoding.
Note: Some supplies are sensitive to backfeeding and may cause jams.
No Disable tag saver. The printer does not move the first tag in the batch backwards before encoding.
If tag saver is disabled and an error occurs during external verification, the tag with an error does not have an overstrike pattern.
Setting the Firs t TID Position
This option only appears in the Advanced Setup menu. The first TID position is only used in non-stop encode mode with singulate mode enabled. The range is 0 to 2000. The default is 0. The first TID position moves the ‘hotspot’ of the first inlay over the antenna so the TID order can be calculated. This process is only used on the first inlay, trailing inlays use the start encode position for setup. The ‘hotspot’ is the antenna’s most sensitive programming area, which varies for each type of inlay.
The first TID position should “trail” after the start encode position; otherwise, error 737 occurs.
Use the RFID Printer Setup Utility to determine the first TID position then enter the value
Tr ai l i ng E dge
Fi rst TI D P osi ti on
0, 0 poi nt
Leadi ng E dge
at the printer.
Select To
Decrease the setting.
Increase the setting.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting RFID Options 8-9
Setting the Start Encode P osition
This option only appears in the Advanced Setup menu. The start encode position is only
used in non-stop encode mode. The printer uses this initial starting position to look for the RFID inlay to program while moving the supply. The range is 10 to 2000. The default is 100.
The start encode position is measured from the leading edge of the supply to the beginning of the RFID inlay encoding area in 0.01 inches.
The start encode position must “lead” (be before) the first TID position; otherwise, error
737 occurs.
Use the RFID Printer Setup Utility to determine the start encode position then enter the
Tr ai l i ng E dge
S tart E ncode P osi ti on
0, 0 poi nt
Leadi ng E dge
value at the printer.
Select To
Decrease the setting.
Increase the setting.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting RFID Options 8-10
Setting the Encode Zone
This option only appears in the Advanced Setup menu. The encode zone is only used in
non-stop encode mode.
The encode zone is the area where the antenna and inlay communicate with each other during programming as the inlay moves over the antenna. It is the length in dots of the programming zone (area). The range is 50 to 2000. The default is 200.
Note:
Encode zone should not exceed the pitch of the label. If the encode zone is too
large, adjacency issues may occur. See “ What is Pitch ” for more information.
An t enna
Use the RFID Printer Setup Utility to determine the encode zone then enter the value at the printer.
Select To
Decrease the setting.
Increase the setting.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting RFID Options 8-11
Verif ying the RFID Inla y Da ta
This option only appears in the Advanced Setup menu. The RFID printer can read/verify the RFID data programmed into an RFID inlay. The default is none.
Note: To externally verify/read programmed RFID data, purchase the optional external verifier.
Exit cover is shown open for visibility. The exit cover does not need to be opened.
Opti onal
E xternal
V eri fi er
Select To
None
Internal
External
Do not verify the programmed RFID data.
Confirms the read EPC data matches the programmed EPC data using the internal antenna.
Confirms the read EPC data matches the programmed EPC data using the optional external verifier. Requires setting the tag verify position.
This option should not decrease throughput because verifying an inlay keeps up with the encoding speed.
Both Confirms the read EPC data matches the programmed EPC data using the internal antenna and optional external verifier. Requires setting the tag verify position.
Note:
Enabling internal or both may decrease throughput.
A checkmark icon appears on the display for a half second once verification is successful.
Setting RFID Options 8-12
Setting the Verif y Pow er
This option only appears in the Advanced Setup menu. The verify power setting increases the strength of the RF Field emitted by the printer’s antenna. Use this power to read a programmed tag. The range is -15 to 23. The default is -15.
Note: Use the lowest power possible to avoid any interference with the internal antenna. Interference may occur between the external verifier and internal antenna because of their close proximity.
Use the RFID Printer Setup Utility to determine the verify power then enter the value at the printer.
Select To
Decrease the setting. If the verify power setting is too low, the RFID inlay in the verifier’s field may not be read.
Increase the setting. If the verify power setting is too high, adjacent
RFID inlays may be read.
Note: Press the left function button to change the amount (by 1 or 10).
Setting the Tag Ve rif y P osition
This option only appears in the Advanced Setup menu. The tag verify position is only
used when Verify is set to external or both. Sets the position for when the label’s leading edge reaches the external verifier. The range is 10 to 2000. The default is 100.
Note: If you continuously receive error 748 (verify mismatch) or 749 (RFID verify fail), adjust the tag verify position.
Use the RFID Printer Setup Utility to determine the tag verify position then enter the value at the printer.
Select To
Decrease the setting.
Increase the setting.
Note: Press the left function button to change the amount (by 1, 10, or 100).
Setting RFID Options 8-13
Enabling Retr y Encode
This option only appears in the Advanced Setup menu. The default is enabled.
Select To
Enable
Disable
The printer tries to reprint and program a label where a supply error occurred. The printer uses the same EPC data from the errored label on the next label. Use with incrementing batches.
The printer does not re-use the same EPC data. Once EPC data is already programmed into an inlay, the printer will not program that same
EPC data again. For example, printing a batch of 100 labels prints 99 labels (or less) if a supply error occurs.
Clearing Da ta
This option only appears in the RFID Advanced menu. The printer keeps track and stores the following items:
♦
♦
The number of RFID inlays successfully programmed.
The number of RFID inlays that failed programming.
Depending on your application and volume of labels printed, clear this data daily or after each batch.
Select To
Yes Clear (erase) all RFID data collected since the last time it was cleared.
No No data is erased. This is the default.
R F I D T ro u b l es h o o t i n g w i t h N o n - S t o p E n co d i n g
If the RFID printer is not encoding any inlays, print a configuration label to check the module type and region of use settings. If the module type and region of use are not compatible, call Technical Support.
If an RFID error occurs when using Easy Setup, call Technical Support.
♦
Try sending the print job with the printer’s speed set to 2.5 ips, disable tag saver, and disable RFID verification. W hen the inlay prints successfully, adjust one setting (print speed, tag saver, verification) at a time and resend the print job. Doing so makes it easier to resolve any errors if they occur.
♦
The start encode position may need to be decreased or increased. The read power level may also need to be increased by 1. Call Technical Support. For detailed descriptions of error messages, refer to the Packet Reference Manual.
If an RFID error occurs when using stop-to-encode mode, call Technical Support.
Setting RFID Options 8-14
P R I N T I N G
This chapter explains the differences between online and offline printing.
Before printing
♦
♦
♦ load supply connect the printer to a host (a PC or a network) make sure the printer is ready to receive data.
D o w n l o ad i n g F i l e s
There are several ways to download files to the printer. Make sure the communication settings at the host match those at the printer.
9
Port Connection
♦
Serial port
Connect the printer to your PC with a serial cable. Use the
Command prompt, terminal emulator (communications) software, such as Tera Term or our MPCL Toolbox software to download files.
Command Prompt Example
COPY LABEL1.FMT COM1
Transmits a file called “LABEL1.FMT” to COM1.
COPY LABEL1.BCH COM1
Transmits a batch called “LABEL1.BCH” to COM1.
If you use the COPY command to download your formats, set flow control to DTR (not XON/XOFF).
♦
USB port
Connect the printer to your PC with a USB cable. Use the
Command prompt or terminal emulator (communications) software, such as Tera Term to download files.
♦
Ethernet
Connect the printer with an Ethernet cable and use MonarchNet2 or other software to download files.
♦
802.11 a/b/g/n network
Connect to the printer using MonarchNet2™ or other software to download files. Refer to the MonarchNet2 Operating Instructions for more information.
The printer accepts files in MPCLII, MLI, or XML format.
MPCLII files include configuration packets, formats, batches (print jobs), fonts, scripts, check digits, or graphics.
Printing 9-1
O n l i n e P r i n t i n g
Online printing means the printer is connected to a host and ready to print data.
1. Design the format using the Packet Reference Manual or using label creation software.
2. Download a format and a batch to the printer.
3. The printer is ready to receive data when you see:
The printer prints the batch (print job).
O f f l i n e P r i n t i n g
Offline printing means entering batch data from a keyboard and printing batches. To use the 939i™ Keyboard or a USB mini keyboard, refer to its Operating Instructions.
To print a format saved into flash memory that contains all fixed data:
1. Design the format to be saved in flash memory using the Packet Reference Manual or using label creation software.
2. Format flash memory. Any formats, graphics, and fonts saved in flash memory are
erased. See “ Formatting Flash Memory ” for more information.
3. When you see “Ready,” download the format.
4. From the Main menu, press until you Data Entry. Press ENTER.
5. Press or to select a format and press SELECT.
DATA ENTRY
Select Format
XXXXXXX →
SELECT BACK
6. Answer the Data Entry Prompts:
Prompts Choices Default
Clear Fields?
Number of Parts
Print Multiple
Yes/No
1 to 5
1 to 32000
No
1
1
Quantity 1 to 32000
Print Now? Yes/No
The printer prints the batch (print job).
1
Yes
Note:
If you change the speed in offline mode, turn off the printer then turn it back on before the change takes effect.
Printing 9-2
U S I N G D I A G N O S T I C S
This chapter explains how to check supply quality and enable a password.
Note: For a complete list of printer error message, refer to the Packet Reference
Manual on our W eb site.
The Service Diagnostics menu can only be accessed by a Service
Representative; it requires a separate password.
1 0
Option
Version
Supply Quality
Password
Choices Default
Firmware/Serial Number/RFID 1/RFID 2/ Easy Setup NA
NA NA
No/Yes No
F a ct o r y S et P a ss w o rd
A password is required to access the diagnostic functions.
Press Feed three times and then press Enter.
C h e ck i n g t h e V er s i o n s
View the version number of the printer’s firmware, RFID module’s firmware, and RFID inlay database. The printer’s serial number is also viewable.
Select To
Firmware
Serial Number
RFID 1
RFID 2
Easy Setup
View the printer’s firmware version.
View the printer’s serial number.
View the RFID module’s version. This is the optional encoder.
View the RFID module’s version. This is the optional external reader.
View the database version number for the RFID inlay database,
d46ESXX.db. Check our web site for updates. See “
RFID Inlay Database ” for more information
Using Diagnostics 10-1
C h e ck i n g S u p p l y Q u a l i t y
The printer continuously stores data from 16 of the most recently printed supplies to check the reflectivity of the sense marks on the supply. Before you check your supply quality, print a batch of supplies or test labels.
Select
Supply Quality
To
View the supply quality.
The message "No data!" appears if you have not printed any labels.
Press
or to display the readings.
Len
Max
The length of the loaded supply in dots.
Should always be greater than Min listing.
OK
U s i n g a P a s sw o rd
Did the sense mark pass the detection test? Y or N
The password feature prevents formats, graphics or fonts from accidentally being deleted from the printer's memory. It limits access to the Setup and Scripts menus by prompting
for a password.
Select To
No Disable the password. The password is not required to access the Setup and Scripts menus.
“No” is the default password setting, therefore it is always shown even if password is enabled.
Yes Enable the password. The password is required to access the Setup and
Scripts menus. Enter the password: press FEED three times then
ENTER.
Note: When password protection is enabled, a password is not required to clear batches, but it is required to clear formats, graphics, and fonts.
Using Diagnostics 10-2
T R O U B L E S H O O T I N G
This chapter includes troubleshooting information for network setup, adjusting the printer to remove ribbon wrinkle, and setting the ribbon’s tension.
For more information about using MonarchNet2™ to configure the printer, refer to the
MonarchNet2 Operating Instructions.
1 1
C o n f i g u ri n g a W i r el e s s P ri n t e r u s i n g a W i r ed Co n n e c t i o n
Depending on the facility’s network, you may need to use a wired connection to initially configure the wireless printer.
Note: The ADTP1 printer has different IP addresses based on connection type: one for wired (Ethernet) and a different one for wireless connections.
The 169.x.x.x IP address is a default address. If this IP address appears on your printer, it indicates the DHCP request failed.
1. Connect an ethernet cable to the printer.
2. Turn on the printer. Once the printer connects to the wired network, you see its IP address on the display.
3. Start your W eb browser.
4. Type in your printer’s IP address and press Enter.
5. Click Log In.
6. Type access for the password and click Submit.
Troubleshooting 11-1
7. From the side Menu Bar, click Network Configuration.
8. From the Protocols tab, set the Boot Method and Boot Tries if necessary. Click Save
Changes. Any changes made on this screen or other screens do not take effect until you click Save/Reboot. This process takes a few minutes.
9. From the SNMP tab, change the System Name (printer’s name) if necessary. Click
Save Changes. Any changes made on this screen or other screens do not take effect until you click Save/Reboot. This process takes a few minutes.
Troubleshooting 11-2
10. From the Wireless Tab, set the SSID, Regulatory Domain, Roam Hysteresis, Mode,
Encryption Mode, Authentication Type, etc. Click Save Changes.
11. From the Protocols Tab, Click Save Changes. Any changes made on this screen or other screens do not take effect until you click Save/Reboot. This process takes a few minutes.
12. The MonarchNet2 screen should refresh and show the new printer’s name with a wired connection.
13. Disconnect the Ethernet cable.
14. Turn off the printer. Wait two seconds, then turn on the printer. You may need to cycle the printer’s power more than once before a wireless connection is established.
15. Once an IP Address appears, Web back into the printer.
Type access for the password and click Submit. To verify the connection, click
Virtual Panel Display, and press Feed. The printer should feed a label.
Troubleshooting 11-3
U s i n g t h e N et w o r k Co n so l e P a c ke t
If you cannot connect the printer to your network using MonarchNet2 (or similar networking tool), try using a wired connection to configure the network printer. If that does not work, send console commands to the printer instead. The network console packet is written in MPCL and accepted through the printer’s serial port.
Syntax
{N,number,action,device,"name" |
C,"con_comds" | }
N1. N
N2. number
N3. action
N4. device
N5. “name”
Network Console Packet.
Number from 0 to 999 to identify the network console packet. 1 is the default.
Action. Enter A to add a network console packet.
Storage device. Enter T to pass the packet through the printer and store the packet in the wireless module.
Packet name, 0 to 8 characters, enclose within quotation marks. “” is the default.
C1. C Command field.
C2. “con_comds” Console commands. Must be enclosed within quotation marks. “” is the default. Each command must be on a separate line. The maximum number of characters per command is 100. Refer to the complete list of console commands in the ADTP1 MonarchNet2 Operating
Instructions for more information.
Note: The maximum number of commands per packet is twenty five (25).
IP Address Example
{N,1,A,T,"protocol" |
C,"set ip me static" |
C,"set ip bot 5" |
C,"set ip add 192.0.0.192" |
C,"set ip sub 255.255.0.0" |
C,"set ip ro 192.1.1.192" |
C,"init" |
C,"exit" | }
Names the packet protocol
Sets method to obtain IP address as static
Sets boot retries to 5
Sets IP address to
192.0.0.192
Sets Subnet Mask to
255.255.0.0
Sets IP Gateway to
192.1.1.192
Saves the settings and initializes the printer
Exits console mode
Troubleshooting 11-4
Wireless Example
{N,1,A,T,"wireless" |
C,"set en mode [in]" |
C,"set en ssid testprt" |
C,"set en enc [128]" |
C,"set en key# 2" |
C,"set en keyval 123456abcdef1" |
C,"set en authtype [open] " |
C,"set en id fnlname" |
C,"set en inap [pap]" |
C,"set en pw <mypsword>" |
C,"init" |
C,"exit" | }
Names the packet
wireless
Sets 802.11b/g wireless mode to infrastructure
Sets wireless SSID to
testprt
Sets wireless encryption mode to 128 W EP
Sets W EP key 2 to use
Sets W EP key 2 value to
123456abcdef1
Sets authentication type to open
Sets the authentication user ID to
fnlname
Sets the EAP inner authentication protocol to
PAP
Sets the password for 802.11b/g EAP authentication to
mypsword
Saves the settings and initializes the printer
Exits console mode
Troubleshooting 11-5
A d j u s t i n g t h e P ri n t e r t o Re mo v e R i b b o n W ri n kl e
Ribbon wrinkle appears as a void or blank line in the printed supply caused by a fold or wrinkle in the ribbon during printing.
Ribbon wrinkle may occur
♦ when the ribbon take-up core is loosely wrapped or contains folds. Rotate the take-up core until it is tight. If that does not help, load a new ribbon.
♦ when there is uneven pressure across the width of the printhead. Make sure the printhead pressure dials are set correctly.
♦ if the supply roll guides and/or supply guides are not set correctly. Make sure the supply is loaded correctly.
Ri bbon W ri nkl e
♦ during normal printer operation. Adjust the ribbon’s tension.
Af t er ri bbon adju stm ent s, no ri bbon w ri nkl e
Troubleshooting 11-6
About the Ribbon’s Take-up Reel
Rotate the take-up reel until the ribbon is tight under the printhead and no wrinkles are visible.
Ri bbon Tak e-up R eel
Troubleshooting 11-7
Adjusting the Printhead Pressure Dials
Two dials are located on either edge of the printhead assembly. Use a coin or flathead screwdriver to adjust the dials based on the width of your supply. The “out of the box”
(default) setting is least pressure, which provides optimal printing in most cases.
If you see smudging, ribbon wrinkling, or poor print quality, adjust the printhead pressure dials.
Note:
Both dials must be set to the same position.
K n o b is se t to l ea s t p re s su r e a d j us t m en t ( k n o bs ar e u p ) .
L e a s t Pr es s ur e
M o s t Pr e ss u re
Each dial has four settings:
Least pressure
Light pressure
Medium pressure
Most pressure
Use the following guidelines to adjust the printhead pressure.
Check print quality and repeat if necessary.
Supply Width Dial Settings
Wide supply
(> 2 inches)
Narrow supply
(≤ 2 inches)
Increase both dials one step.
Decrease both dials one step.
If print quality does not improve, try adjusting the ribbon tension or contact Technical Support.
Troubleshooting 11-8
S e t t i n g t h e S u p p l y G u i d e s
1. Adjust the roll guides to fit your supply roll and place rolled supply on the holder. The supply roll must move freely.
Di e Cut S ensor
Ni bs
S uppl y Leve r
2. Unlock the supply guides and feed the supply through the supply path so a few inches extend past the front of the printer. Tuck the supply under the nibs and die cut sensor.
3. Adjust the supply guides so they barely touch the supply. Turn the supply lever up to lock it in place.
Troubleshooting 11-9
Adjus ting the Ribbon Tension
Rotate the ribbon take-up guide to adjust for even tension across the width of the ribbon.
This adjustment moves the outside end of the ribbon roller to change the pressure on the ribbon. A properly adjusted ribbon provides consistent ribbon tracking and reduced opportunity for ribbon wrinkles.
Note: A Phillips head screw driver is needed.
4. Load 4-inch wide thermal transfer supply with a 4-inch wide ribbon.
5. Set the printhead pressure dials to an equal setting.
6. Loosen the locking screw on the end of the ribbon take-up guide, set the guide at the nominal position.
Ri bbon Tak e-up
Gui de
7. Print several labels and check for ribbon wrinkle. If necessary, turn the guide clockwise to increase tension. Print several labels and check for even tension across the ribbon with no creases or wrinkles.
8. Hold the ribbon take-up guide and tighten the screw.
If wrinkles occur again, repeat the adjustment.
If print quality does not improve, a service adjustment may be necessary. Contact
Technical Support.
Troubleshooting 11-10
S P E C I F I C AT I O N S & A C C E S S O R I E S
P r i n t e r
Height:
Width:
Depth:
Weight:
13.8 inches (351.1 mm)
11.6 inches (293.5 mm)
21.7 inches (550.8 mm)
33 lb. (15 kg)
A
Specifications & Accessories A-1
Shipping Weight:
38 lb. (17.3 kg)
Power Source: 90-264 V
A C
with autoselect 50/60Hz
Operating Limits: Thermal Transfer (ribbon): 40° to 95°F (4° to 35°C)
Thermal Direct: 40° to 104°F (4º to 40°C)
Storage:
Humidity:
15°F to 120°F (-10°C to 49°C)
5% to 90% non-condensing
Memory:
Processor:
Printhead:
64MB RAM; 32MB Flash
400 MHz
Thermal at 4.09 inches (103 mm) wide
203 dpi (8.0 dots per mm)
Printing Method:
Print Speed:
Max Print Area:
Thermal Transfer (ribbon) or Thermal Direct
2.5 ips default for all serial bar codes,4.0 ips, 6.0 ips, 8.0 ips,
10.0 ips, or 12.0 ips
4.09 inches x 16.0 inches (103 mm x 406 mm) with 203 dpi
4.09 inches x 12.0 inches (103 mm x 305 mm) with optional 300 dpi
RFID:
S u p p l i e s ( M ed i a)
902 – 928 MHz frequency range (FCC)
865.6 – 867.6 MHz frequency range (ETSI) the radio operates within the frequency range in accordance with local rules and regulations.
Contact your Sales Representative for supply recommendations in high temperature and/or high humidity environments.
Supply Widths: 0.75 inches (19 mm) minimum for labels and tags
4.32 inches (108 mm) maximum for labels and tags
Supply Lengths: 0.32 inch (8 mm) minimum for non-indexed (continuous) supply
0.50 inch (13 mm) minimum for die cut/black mark/aperture supply
1.50 inches (38 mm) for peel mode
17.5 inches (444.5 mm) maximum for labels and tags
16 inches (406 mm) maximum;
12 inches (305 mm) maximum with optional 300 dpi
0.75 inch (19 mm) minimum for tags
1.2 inches (30 mm) minimum for cutting tags
Total Thickness:
5.6 to 14 mils
5.6 to 12.2 mils with the optional cutter
5.6 to 13.2 mils with RFID
Max. Roll Diameter: 9.375 inches (238 mm)
Supply Core: 3.0 inches (76 mm) minimum
4.0 inches (101.6 mm) maximum
String Ta gs
Widths:
Lengths:
Thickness:
0.90 inches (23 mm) minimum
2.0 inches (51 mm) maximum
0.78 inch (20 mm) minimum
2.0 inches (50 mm) maximum
5.6 to 14 mils
Specifications & Accessories A-2
String Loop Length: 0.63 inches (15.8mm) minimum
1.5 inches (38 mm) maximum
String Orientation: Facing operator
Wind Direction:
R i b b o n
Face out
Do not leave ribbon in sunlight, high temperatures or humidity.
Ribbon Type: Standard (wax, high speed)
Premium (wax resin, TUFF-MARK® resin)
Ribbon Widths Use with M aximum supply width
1.5 inches (38 m m )
1.8 inches (46 m m )
2.3 inches (58 m m )
3.3 inches (84 m m )
1.3 inches (33 m m )
1.5 inches (38 m m )
2.0 inches (51 m m )
3.0 inches (76 m m )
4.3 inches (110 mm ) 4.0 inches (102 mm )
Note: Use a ribbon wider than your supply.
23,600 inches (600 meters) Ribbon Length:
C a b l e P i n o u t s
The following tables show the connector pins for the serial 9-pin to 9-pin (126716) cable.
9-Pin (M ) To 9-Pin (F)
SHIELD
1
RCV 3
TX 2
CTS 6
RTS 4
DTR 8
DSR 7
+5V 9
SGND 5
SHIELD
1
3 RCV
2 TX
6 CTS
4 RTS
8 DTR
7 DSR
9 +5V
5 SGND
Specifications & Accessories A-3
A c c e s so ri e s
♦
928™ Stacker
♦
935™ External Rewind
♦
939i™ Intelligent Keyboard
♦
Supply Guide Extension (131438)
♦
USB cable (126738)
♦
203 dpi (128933ST)
300 dpi (130226) Replacement
Printhead
♦
Printhead CLEAN-STRIP (120350)
F a ct o r y - I n s t a l l ed O p t i o n s
♦
933 Cutter
♦
938™ Verifier
♦
USB mini keyboard (160001)
♦
Tear Bar (131439)
♦
Serial Cable: 9-pin to 9-pin (126716)
♦
Packet Reference Manual –
Programmer's manual (TCADTP1PR)
♦
Printhead Cleaning Pen (114226)
♦
Internal Ethernet with
MonarchNet2™
♦
Peel mode
♦
Cutter Ready
♦
RFID Encode
♦
300 dpi printhead
♦
802.11a/b/g/n wireless with
MonarchNet2™
♦
Peel mode with internal liner take-up
♦
Cart Ready for use on Mobile
Workstation
♦
RFID Encode and Verify
(not available with peel mode)
♦
ADK script programming for special applications
S h i p p i n g t h e P ri n t er
If you need to ship the printer to a different location and do not have the original packaging, use the following part numbers to order the appropriate packaging materials.
1. Remove the ribbon roll, if one is loaded.
2. Remove the supply roll, if one is loaded.
3. Close the printhead by pressing down on the thumb well until it clicks into place.
4. Place the printer in the original box and secure with packaging material. Make sure the printer is adequately packed to avoid damage during shipment.
Part Number Description and (Qty.) Part Number Description and (Qty.)
70101
70102
70103
70110
Shipping carton (1)
Bottom Pad (1)
Top Pad (1)
Scored Insert (1)
70107
70108
70109
00054301
Foam Support, Horizontal (1)
Foam Support, Vertical (1)
Angleboard (4)
Poly Bag (1)
Specifications & Accessories A-4
M E N U S T R U C T U R E
Use the Function button to select MENU. Then, use
or to scroll through options. Press SELECT when you see the menu option you need.
B
Menu Structure B-1
Menu Structure B-2
G L O S S A R Y
G
The following terms will help you use this manual.
continuous mode The printer prints all the labels in the job (batch) without stopping.
download (send)
EPC
Transmission of data from the host to your printer.
The Electronic Product Code, which is a numbering standard for items, similar to the UPC code for bar coding. The EPC is divided into several sections: Header, Manager Number, Object
Class, and Serial Number. The amount of EPC memory varies with the inlay types. Used for RFID programming.
format
host
inlay
Supply layout or design that is downloaded to the printer.
Any mainframe, minicomputer, data collect terminal, or personal computer sending data to the printer.
A type of media that contains a transponder and is converted for use in Monarch® RFID supplies (tags). Inlays can be made with different types of transponders.
interrogator
LCD
leader
Liner take-up mode
on-demand mode
peel mode
print job (batch)
offline mode
online mode
The electronics module that programs the RFID inlays through the antenna.
Display on the printer used to indicate printer conditions and problems.
Wrap around a new roll of ribbon with printing on it.
The printer collects the backing paper (liner) on a reel after the label is printed.
The printer stops after each label is printed for removal and application before printing the next label.
The printer separates the backing paper (liner) from the label after printing.
Actual data printed on a label or tag. The host may download the print job together with the format, or as a separate packet.
The print job is also called a "batch."
The printer does not need a connection to a host to print.
The printer requires a connection between a network/computer to print.
Glossary G-1
read power
RFID inlays
supply sensor
supplies
TID transponder write power
Increase or decreases the strength of the RF field emitted by the printer’s antenna to read a programmed inlay.
Supplies that contain an embedded programmable chip and antenna.
Senses whether supply is loaded or needs to be loaded in the printer. Located in the supply path.
Labels and tags used for printing.
The Transponder Identification Number, which contains the chip type, features, and available custom commands supported for tag authentication.
The combination of the embedded programmable chip with an antenna on some type of media (film, paper, etc.).
Increase or decreases the strength of the RF field emitted by the printer’s antenna to program the inlay.
Glossary G-2
AMERICAS
170 Monarch Lane
Miamisburg, OH 45342
937 865 2123 (direct)
Tel +800 543 6650
(8:00 a.m. – 6:30 p.m., EDT)
Fax +937 865 6663
ASIA
No. 7 Chun Ying Street
Tseung Kwan O Industrial Estate
New Territories, Hong Kong
Tel +852 2372 3169
Fax +852 2995 0014
WESTERN EUROPE
1 Thomas Road
Wooburn Green
Bucks HP10 0PE
Tel +(44) 1628 859500
Fax +(44) 1628 859567
ASIA PACIFIC
NEW SOUTH WALES
61 Vore Street
Silverwater NSW 2128
Tel +(02) 9647 1833
Fax +(02) 9647 1914
Toll free (Outside Sydney only) averydennison.com/printers
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement