advertisement
▼
Scroll to page 2
of 8
INSTALLATION INSTRUCTIONS Small Flat Panel In-Wall Swing Arm Mount FWDIW Series FWDIW Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® and Centris are registered trademarks of Milestone AV Technologies. All rights reserved. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the FWDIW up to (and including) the display does not exceed 40 lbs (18.14 kg). WARNING: Use this mounting system only for its intended IMPORTANT SAFETY INSTRUCTIONS WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. use as described in these instructions. Do not use attachments not recommended by the manufacturer. WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Do not use this product outdoors. --SAVE THESE INSTRUCTIONS-WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. LEGEND 2 Tighten Fastener Hex-Head Wrench Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Apertar fixador Chave de cabeça sextavada Serrare il fissaggio Chiave esagonale Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé à tête hexagonale Loosen Fastener Phillips Screwdriver Aflojar elemento de fijación Destornillador Phillips Befestigungsteil lösen Kreuzschlitzschraubendreher Desapertar fixador Chave de fendas Phillips Allentare il fissaggio Cacciavite a stella Bevestiging losdraaien Kruiskopschroevendraaier Desserrez les fixations Tournevis à pointe cruciforme Installation Instructions FWDIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS 3/16" (Included) B (4) 2 short (SIDES) 2 long A (1) [swing arm] I/M x1 C (4) 5/16-18 x 5/8" G (2) [bumper] L (12) [adhesive square] H (2) [cable management cover] M (4) [cable tie mount] Q3 (6) 1/8" P (4) [cable tie] N (1) 3/16" R Q4 (1) [100 x 200 VESA bracket] Q2 (6) M4x16mm K (2) 08 x 1/2" J (4) 8-32 x 3/8" Q (with FWDIWVB only) Q1 (4) M4x8mm F (1) [bumper mounting bracket] E (4) 1/4" D (4) 5/16" R1 (4) M4x12mm R3 (4) 3/8" R5 (4) R2 (4) M4x30mm M4x20mm R4 (4) 3/4" 3 FWDIW Series Installation Instructions Installation The following procedure assumes that a Chief Model FAC501 In-Wall accessory has previously been installed following the installation instructions provided by the manufacturer. If a FAC501 is not installed or there are any other questions regarding the installation of this accessory, immediately contact Chief. Swing Arm Mounting Bracket 5 WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT deviate from installation instructions provided. DO NOT substitute hardware. 3 Install Bumper 1. 4 Install two bumpers (G) to bumper mounting bracket (F). (See Figure 1) NOTE: A screwdriver may be required to push bumper into hole in bumper mounting bracket. 2. Secure bumper mounting bracket (F) to FAC501 onto the side the arm will be located on when retracted using two Phillips pan head screws (K). (See Figure 1) Lower Support Plate Figure 2 1 6. (F) x1 (G) x2 Secure swing arm to FAC501 using four button head cap screws (C), four lock washers (D) and four flat washers (E). NOTE: The mounting holes in the swing arm mounting bracket are slotted horizontally to allow the mount to be slightly off-center to provide better cable clearance. 2 (K) x2 6 (C) x4 Figure 1 3. Align bottom of swing arm pivot pin with hole in lower support plate. (See Figure 2) 4. Lower swing arm until pivot pin rests in hole in lower support plate. (See Figure 2) 5. Align four mounting holes in swing arm mounting bracket with four mounting holes in FAC501. (See Figure 2) 4 (D) x4 Figure 3 (E) x4 Installation Instructions FWDIW Series Display Installation The mounting holes on the back of the display will either be flush with the back surface, or recessed into the back surface. Refer to the applicable installation procedure below. NOTE: If interface bracket is required, proceed to Attach 2 3 Interface Bracket to Display section. Flush Mount Display WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes. Ensure that screws are not too long. WARNING: IMPROPER INSTALLATION CAN LEAD TO 4 DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris bracket! 1. Partially install two screws (R1) into upper mounting holes in display back. (See Figure 4) NOTE: Leave at least 1/8" of each screw protruding out back (R1) x 2 Figure 5 Recessed Mount 1. Place four spacers (R3, R4) over each mounting hole in display back. (See Figure 6) 2. Align teardrop mounting holes in faceplate with holes in spacers (R3, R4). (See Figure 6) 3. Install four Phillips pan head screws (R2) through faceplate and spacers (R3, R4) and into mounting holes in back of display. (See Figure 6) 4. Tighten all screws. 5. Proceed to Cable Management Section. of display. 1 2 1 (R1) x2 Figure 4 2. Align two screws (R1) in display back with upper teardrop mounting holes in faceplate. (See Figure 5) 3. Place two screws (R1) in display back into upper teardrop mounting holes in faceplate and lower display until screws are seated in lower area of teardrop mounting holes. (See Figure 5) 4. Install two screws (R1) through lower mounting holes in faceplate and into display back. (See Figure 5) 5. Tighten all hardware. 6. Proceed to Cable Management Section. 3 (R2) x 4 (R3, R4) x 4 Figure 6 5 FWDIW Series Installation Instructions Attach Interface Bracket to Display (FWDIWVB only) 1. Lay display face down on a clean and dry flat surface. 2. Attach Interface Bracket (Q4) to display using six M4x16mm Phillips flat machine screws (Q2) and six 1/8" spacers (Q3). (See Figure 7) 3. Tighten all screws. (Q4) (Q4) (R1) x 4 (Q2) x 6 (Q3) x 6 Figure 9 Cable Management Figure 7 Attach Display to Mount (FWDIWVB only) 1. 2. 1. Start two M4 x 12mm Phillips pan head screws (R1) into top mounting holes on interface bracket (Q4). (See Figure 8) Align two screws in interface bracket (Q4) with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes. (See Figure 8) Attach all cables to display. CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched by installation of cover (H) or screws (J). 2. Carefully insert cables in cavity located in lower portion of mount arm. (See Figure 10) 3. Using Phillips screwdriver, install cover (H) with two screws (J) per arm. (See Figure 10) 2 (Q4) Cable Path (typical) (H) x 2 (R1) x 4 3 (J) x 4 Figure 8 3. 6 Hold display so that display back is against Centris cup and install two M4 x 12mm Phillips pan head machine screws (R1) through lower mounting holes in Centris cup and into lower mounting holes in interface bracket (Q4). (See Figure 9) Figure 10 Installation Instructions FWDIW Series Trim Installation To install optional trim; 1. Remove paper covering adhesive and affix three tape squares (L) to inside lower flange of each trim piece (B). (See Figure 11) 2. Orient trim pieces (B) as shown in figure below. (See Figure 11) 3. Remove paper covering adhesive back from tape squares (L) on trim and press trim (B) against inner wall of box. (See Figure 11) 2 3 Figure 12 (B) x 4 (L) x 12 To adjust display Roll, Pitch, and YAW tension: Figure 11 1. Disconnect all wires and cable from the display. Adjustments 2. Remove two Lower screws securing display to Centris cup. Swing Arm 3. Loosen two Upper screws securing display. 4. Lift display upward and away from mount. 5. Using a Phillips screwdriver turn the tension adjustment screw clockwise to increase tension, or counter-clockwise to decrease tension. (See Figure 13) 6. Re-install display. PIVOT / SWING Tension 1. Using 3/16" hex key (N), slightly loosen or tighten the adjustment screw(s) as necessary. (See Figure 12) Figure 13 7 FWDIW Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002162 Rev 00 2012 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 03/12 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project