advertisement
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 1
OWNER’S
MANUAL
DVD PLAYER with VIDEO CASSETTE RECORDER
DVC860D
ReWritable Recordable
DVD
STOP PLAY
OPEN/CLOSE
DVD
DVD
OUTPUT
VCR TIMER REC REC
VCR
REW F.FWD
VIDEO L AUDIO R
POWER
CHANNEL
STOP/EJECT
PLAY
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call TOLL FREE : 1-800-968-3429 or visit our web site at http://www.funai-corp.com
Please read before using this equipment.
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO
NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
– 2 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 3
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments - Do not use attachments not recommended by the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories - Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
14. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.
18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance this indicates a need for service.
20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.
22. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
– 3 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 4
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR COMBINATION UNIT. This serial number is unique to your machine. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Remote control
SUPPLIED ACCESSORIES
Two AA batteries A/V cables RF Cable
(NA209UD)
(NA259UD)
(approx. 3 feet (100 cm) long) (WPZ0102TM015)
WPZ0901TM002
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
VCR
: Description refers to playback of video cassette tapes.
DVD-V
: Description refers to playback of DVD video discs.
CD
: Description refers to playback of audio CDs.
MP3
: Description refers to playback of MP3 discs.
QUICK
: Description refers to the items to be set in the QUICK mode.
– 4 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 5
TABLE OF CONTENTS
■ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
■ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
■ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
■ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 11
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 11
■ VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
■ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTING TO A TV WITHOUT A/V TERMINALS . . . 13
CONNECTING TO A TV WITH A/V TERMINALS. . . . . . . 13
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14
CONNECTING TO A STEREO AMPLIFIER EQUIPPED
WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR
DAT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A RECEIVER WITH
DOLBY DIGITAL DECODER . . . . . . . . . . . . . . . . . . . . . . . 15
CONNECTING TO AN ANALOG AUDIO SYSTEM. . . . . . 15
■ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16
TO CHANGE THE ON-SCREEN LANGUAGE . . . . . . . . . . 17
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
■ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
■ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . . . . . . 19
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20
■ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21
MTS (Multi-Channel Television Sound) SYSTEM . . . . . . . . 21
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 22
■ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 23
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 26
TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 29
■ DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
AUDIO SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
■ TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 32
■ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
■ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
INDICE
■ CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
■ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
■ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DVD/VCR A CONEXIÓN DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CANAL DE SALIDA DE RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VÍDEO o TOMAS DE ENTRADA DE VÍDEO
COMPONENTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O
PLATINA DAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN AUDIO ANALÓGICO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
■ PREPARACIÓN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACIÓN DE CANAL AUTOMÁTICA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACIÓN DE RELOJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
– 5 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 6
FEATURES
¡ Virtual Surround Sound
DVD Mode
¡ Dolby Digital sound
This DVD/VCR COMBINATION UNIT can output a
Dolby Digital audio signal.
¡ Component Video Out Jacks
Jacks located on the back of the DVD/VCR COMBINA-
TION UNIT which are used to send high-quality video to a TV via Component Video In Jacks.
¡ Still/fast/slow/step playback
¡ Bit rate indication
¡ Random playback for audio CD and MP3
¡ Program playback for audio CD and MP3
¡ DRC (Dynamic range control)
You can control the range of sound volume.
¡ DVD menus in a desired language
¡ Black Level Setting
¡ Screen saver/Auto power-off functions
The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program is activated for 30 minutes, the power automatically turns off.
VCR Mode
Hardware specifications
¡ Auto Head Cleaner
¡ 4 Head HiFi Stereo
¡ Subtitles in a desired language
¡ Selecting a camera angle
¡ Trilingual on-screen menu display selectable in
English, French, or Spanish
¡ Choices for audio language and sound mode
¡ Parental lock
¡ Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡ 181 channel capability PLL frequency synthesizer tuner with direct station call
(A cable converter box may be necessary to view scrambled cable channels.)
Automatic functions
¡ Playback MP3 disc
¡ Direct Search
¡ Auto power on system
Automatically turns the VCR on when you insert the cassette.
¡ On-screen display
Information about the current operation can be displayed on the TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.
¡ Digital Auto Tracking (DTR)
Playback
¡ Auto Repeat
¡ 2 Step Picture Search Operation
¡ Search
Chapter search / Title search / Track search / Time search
¡ Index Search
¡ Repeat
Chapter / Title / Track / Group / All / A-B
¡ Time Search
¡ Zoom
¡ Marker
The part designated by user can be called back.
Recording
¡ 1 Year, 8 events (including Daily and Weekly Timer
Recording)
¡ OTR (One Touch Recording)
¡ Resume Play
PRECAUTIONS
INSTALLATION LOCATION
For safety and optimum performance of your
DVD/VCR COMBINATION UNIT:
• Install the DVD/VCR COMBINATION UNIT in a horizontal and stable position. Do not place anything directly on top of the DVD/VCR COMBINATION
UNIT. Do not place the DVD/VCR COMBINATION
UNIT directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the DVD/VCR COMBINATION
UNIT. Avoid locations subject to strong vibration or strong magnetic fields.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR
COMBINATION UNIT, unplug the power cord immediately and take the unit to our Authorized Service
Center for servicing.
• Do not put your fingers or objects into the DVD/VCR
COMBINATION UNIT cassette holder.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the DVD/VCR COMBINATION
UNIT at least for 2 hours until its inside is dry.
– 6 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 7
ABOUT THE DISCS
PLAYABLE DISCS DISC TYPES
The following discs can be played back on this
DVD/VCR COMBINATION UNIT.
¡ DVD video ¡ DVD-R/RW*
¡ DVD+R/RW* ¡ Audio CD
¡ CD-R/RW* ¡ MP3*
* Depending on the types or the writing method of the medium some discs can not be played.
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs made on personal computers, or on DVD recorders may not be played back properly due to factors such as scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played back properly due to different environments or the settings of the application you use. We recommend always to use the standardized, properly formatted discs.
(Please contact the sales agency for more detail).
[DVD]
Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If a function you selected does not run as desired, refer to the manual accompanying the disc.
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡ Some discs include region codes as shown below.
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
¡ The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on DVD/VCR COMBINA-
TION UNIT with the same region code.
The following discs cannot be played back on this
DVD/VCR COMBINATION UNIT.
¡ DVD with region codes other than 1 or ALL.
¡ DVD-ROM
¡ DVD-RAM (Never play back, otherwise malfunction may result.)
¡ CD-ROM
¡ VSD
¡ CDV (Only plays back the audio part.)
¡ CD-G (Only plays back the sound.)
¡ CD-I (Never play back, otherwise malfunction may result.)
¡ SACD
¡ Photo CD (Never play back, otherwise malfunction may result.)
¡ Video CD (Never play back, otherwise malfunction may result.)
Any other discs without compatibility indications.
[MP3]
Data on an MP3 is divided into sections called "groups", and then into subsections called "tracks", each of which is given a group or track number.
Example
Group 1
Track 1 Track 2 Track 3 Track 4
Group 2
Track 1 Track 2
– 7 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 8
OPERATING CONTROLS AND FUNCTIONS
FRONT PANEL
1 2 3 4 5 6 7 8
OPEN/CLOSE
POWER
CHANNEL STOP/EJECT
PLAY
DVD
STOP PLAY
DVD
DVD
OUTPUT
VCR TIMER REC REC
VCR
REW F.FWD
VIDEO L AUDIO R
22
21
20
19
– 8 –
18
17
16
15
14
13
12
11
10
9
REMOTE CONTROL
23
25
27
29
24
26
28
30
31
32
33
34
35
37
36
POWER SPEED AUDIO
1
4
2
5
7 8
DISPLAY
0
DVD
3
SKIP/CH.
6
VCR/TV
9
SLOW
+ 10
VCR PAUSE
RECORD
PLAY
STOP
MENU
SETUP TITLE
ENTER
RETURN
MODE ZOOM
SEARCH
MODE
CLEAR/
C.RESET
SUBTITLE ANGLE REPEAT A-B
T-SET
51
49
50
48
47
46
45
43
52
44
42
41
39
40
38
1.
Disc loading tray
2.
OPEN/CLOSE Button [page 22]
Press to insert discs into or remove them from the tray.
3.
DVD OUTPUT Light (Green) [page 12]
This light appears when the DVD output mode is selected. You can only watch DVDs when the green DVD
OUTPUT light is on. To make the green DVD OUT-
PUT light come on, press DVD on the remote control or
OUTPUT on the front panel.
4.
VCR OUTPUT Light (Green) [page 12]
This light appears when the VCR output mode is selected. You can only watch tapes when the green VCR
OUTPUT light is on. To make the green VCR OUTPUT light come on, VCR on the remote control or OUTPUT on the front panel.
5.
CASSETTE COMPARTMENT
6.
POWER Button [page 16]
Press to turn the power on and off.
7.
POWER Light
This light appears when the power is on.
8.
STOP/EJECT Button (VCR)
EJECT Button
Press to remove the tape from the VCR.
STOP Button
Press to stop the tape motion.
9.
PLAY Button(VCR) [page 18]
Press to begin playback.
10.
CHANNEL Buttons [page 16]
In VCR mode, press to change TV channels on the
VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture.
11.
AUDIO In Jacks [page 21]
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.
12.
VIDEO In Jack [page 21]
Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source (laser disc player, camcorder, etc.) here.
13.
F.FWD Button (VCR) [page 18]
Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search).
14.
REW Button (VCR) [page 18]
Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search).
15.
REC/OTR Button [page 19]
Press once to start a recording. Press repeatedly to start a One-Touch Recording.
16.
REC Light [page 19]
Lights up during recording.
17.
TIMER REC Light [page 20]
This light appears when the DVD/VCR is in standby mode for a timer recording or during a One-Touch
Recording. It flashes if T-SET is pressed for a timer recording, but there is no tape in the DVD/VCR. It flashes when all timer recordings or One-Touch
Recordings are finished.
EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:47 PM Page 9
18.
OUTPUT Button [page 12]
Press to select DVD mode or VCR mode.
● You can switch the output mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing DVD or
VCR on the remote control.
19.
Remote Sensor Window
20.
Display
21.
PLAY Button (DVD) [page 22]
Press to begin playback.
22.
STOP Button (DVD) [page 22]
Stops operation of the disc.
23.
SPEED Button [page 19]
Press to select the VCR’s recording speed (SP or SLP)
24.
POWER Button
Press to turn the power on and off.
25.
Number Buttons
● DVD mode [page 24]
Press to select numbered items in a menu.
+10
Use this button to enter number 10 and above.
● VCR mode [page 16]
Press to select TV channels on the VCR.
To select channels, enter channel numbers as a twodigit number for the quickest results. For example, to select channel 6, press 0 then 6.
26.
DISPLAY Button
● DVD mode [page 28]
Press to access or remove the display screen during
DVD or Audio CD playback.
● VCR mode [page 21]
Press to access or remove the VCR’s on-screen status display.
27.
DVD Button [page 12]
Press to select DVD mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing
DVD or VCR on the remote control.
28. h Button
● DVD mode [page 23]
Press to view the DVD picture in fast reverse motion.
Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the reverse speed of slow motion.
● VCR mode [page 18]
Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind
Search).
29.
STOP Button
● DVD mode
Press to stop the disc motion.
● VCR mode
Press to stop the tape motion.
30.
RECORD Button [page 19]
Press once to start a recording.
31.
MENU Button
● DVD mode [page 23]
Press to display the menu of the Disc.
● VCR mode [page 17]
Press to access the VCR menu.
32.
TITLE Button [page 23]
33.
SETUP Button [pages 28-31]
Press to enter DVD player setup mode.
34.
ZOOM Button [page 24]
Enlarges part of a DVD-reproduced image.
35.
MODE Button [pages 26, 27, and 30]
Activates program playback or random playback mode when playing CDs or MP3. Sets Black level and virtual surround.
36.
SUBTITLE Button [page 27]
Press to select the desired subtitle language.
36.
T-SET Button [page 20]
Press to put the VCR into standby mode for a timer recording.
37.
ANGLE Button [page 27]
Press to change the camera angle to see the sequence being played back from a different angle.
38.
REPEAT Button [page 25]
Repeats playback of the current disc, title, chapter or track.
39.
A-B REPEAT Button [page 25]
Repeats playback of a selected section.
40.
SEARCH MODE Button
● DVD mode [page 24]
Press to access or remove the Search display, which allows you to go directly to a specific
Title/Chapter/Track/Time.
● VCR mode [page 18]
Press to perform a Time Search or an Index Search.
41.
CLEAR/C.RESET Button
● DVD mode [pages 24, 25]
Press to reset the setting.
● VCR mode [page 18]
Press to reset the counter. Press to exit from the
MENU screen.
42.
RETURN Button [page 30]
● DVD mode
Returns to the previous operation.
43.
Arrow Buttons
Use when making settings while watching the display on a TV screen.
● VCR mode [page 16] p /o Buttons
Press to enter digits when setting program (For example: setting clock or timer program). Press to select the setting modes from the on screen menu.
B Button
When setting program (For example: setting clock or timer program), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numbers during channel preset.
s Button
Press to cancel a setting of timer program. Press to correct digits when setting program (For example: setting clock or timer program). Press to add or delete channel numbers during channel preset.
44.
ENTER Button
● DVD mode [page 22]
Press to accept a setting.
– 9 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 10
45. g Button
● DVD mode [page 23]
Press to fast forward the Disc. Press PAUSE, then press this button to begin slow motion playback.
Press this button repeatedly to change the forward speed of slow motion.
● VCR mode [page 18]
Press to rapidly advance the tape, or view the picture rapidly in forward during playback (Forward Search).
46.
PLAY Button
● DVD mode
Press to begin playback.
● VCR mode
Press to begin playback.
47.
VCR Button [page 12]
Press to select VCR mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing DVD or
VCR on the remote control.
48.
PAUSE Button
● DVD mode [page 22]
Press to pause Disc playback. Press repeatedly to advance the DVD picture step by step (or one frame at a time).
● VCR mode [page 19]
While recording, press to temporarily stop the recording (pause). Press a second time to resume normal recording. You can not pause a One-Touch
Recording. Or, press during tape playback to freeze the picture. Press to advance the picture one frame at a time during still mode.
49.
SLOW Button [page 18]
During tape playback, press to view the video tape in slow motion. Press again to resume normal playback.
This button does not affect DVD playback.
50.
VCR/TV Button [page 19]
Use to select VCR or TV position.
● VCR Position
To view playback, to monitor video recordings or to watch TV using the VCR tuner.
● TV Position
To watch TV or to view one program while recording another.
51.
SKIP/CH. Buttons
● DVD mode
Press to skip Chapters or Tracks.
● VCR mode
Press to change TV channels on the VCR.
52.
AUDIO Button [page 27]
Press to select a desired audio language or sound mode.
Notes
¡ To use the remote control to operate the DVD/VCR
COMBINATION UNIT and its features, press DVD on the remote control before pressing other DVD’s operation buttons. Verify that the green DVD OUT-
PUT Light is on.
¡ To use the remote control to operate the VCR and its features, press VCR on the remote control before pressing other VCR’s operation buttons. Verify that the green VCR OUTPUT Light is on.
REAR VIEW
53 54 55 56 57
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
ANT-OUT
R
VIDEO OUT VIDEO IN
R
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
66
65 61 60
59 58
53.
ANT-IN (Antenna In) Jack
Connect your antenna, Cable Box, or Satellite decoder box.
54.
DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment.
55.
AUDIO IN Jacks
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.
56.
AC Power Cord
Connect to a standard AC outlet to supply power to the
DVD/VCR COMBINATION UNIT.
DVD Playback only
57.
COMPONENT VIDEO OUT Jacks
Connect optional component video cables here and to the component Video In jacks of a television.
58.
COAXIAL Jack
Connect an optional coaxial digital audio cable here and to the Coaxial Digital Audio In jack of a decoder or audio receiver.
– 10 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 11
59.
DVD ANALOG AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment (DVD only).
60.
S-VIDEO OUT Jack
Connect an optional S-Video cable here and to the S-
Video In jack of a television. (DVD only)
61.
VIDEO IN Jack
Connect a cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
62.
DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here and to the TV’s Video In jack.
63.
ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this jack to the ANTENNA IN Jack on your TV.
Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the player.
DISPLAY
Stays on when the
A-B repeat function is on.
Stays on when the repeat function is on.
Stays on when repeat title function is on.
DVD
Lights up when a DVD is inserted into the tray.
Stays on when repeat track function is on.
Stays on when repeat chapter function is on.
DISPLAYS DURING OPERATION
No disc inserted or playing
DVD menu
Tray open
Tray closed
Loading the Disc
Lights up when the inserted disc comes to a pause.
Stays on when the inserted disc is being played back.
Lights up when a
CD is inserted into the tray.
Displays how long a current title or track has been played back. When a chapter or track has switched, the number of the a title, chapter or track is displayed.
LOADING THE BATTERIES
1. Open the battery compartment cover.
2. Insert two AA batteries, with each one oriented correctly.
3. Close the cover.
VCR
Stays on during playback when the repeat function is on.
Notes
¡ Do not mix alkaline and manganese batteries.
¡ Do not mix old and new batteries.
Lights up when the playback is in a still or in a slow mode.
Stays on when the inserted cassette is being played back.
Works as a clock, or a tape counter.
Also displays a channel number, and remaining time for OTR
– 11 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 12
VCR/DVD SWITCHING
Because this product is a combination of a VCR and DVD player, you must first select which component you wish to operate with the OUTPUT BUTTON.
VCR MODE
Press VCR on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
DVD MODE
Press DVD on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
Notes
¡ Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need to select the correct mode on the remote control too.
DVD
STOP PLAY
OPEN/CLOSE
DVD
DVD
OUTPUT
VCR TIMER REC REC
VCR
REW F.FWD
VIDEO L AUDIO R
POWER
CHANNEL STOP/EJECT
PLAY
POWER SPEED AUDIO
1
4
2
5
7 8
DISPLAY
0
DVD
3
SKIP/CH.
6
VCR/TV
9
SLOW
+ 10
VCR PAUSE
DVD
OUTPUT
DVD button
DVD OUTPUT Light
VCR button
VCR TIM
VCR OUTPUT Light
OUTPUT button
PLAY
STOP
RECORD
MENU
SETUP TITLE
ENTER
RETURN
MODE ZOOM
SEARCH
MODE
CLEAR/
C.RESET
SUBTITLE ANGLE REPEAT A-B
T-SET
– 12 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 13
HOOKUPS
CAUTION:
¡ Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected.
¡ Read through the operation manual for the equipment to be connected.
¡ Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡ Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you are watching television programs.
CONNECTING TO A TV WITHOUT A/V TERMINALS
1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of the DVD/VCR COMBINATION UNIT.
4. Connect the DVD/VCR COMBINATION UNIT to the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNIT and TV into the AC outlets.
[VHF/UHF
combination antenna]
[Indoor antenna]
OR
From Cable or
Satellite Company
[Cable box or satellite box]
OR
IN
OUT
[Back of the DVD/VCR]
[Back of the
UHF/VHF combination TV]
RF cable
(supplied)
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
UHF/VHF
R
ANT-OUT VIDEO OUT VIDEO IN
R
RF OUTPUT CHANNEL for DVD/VCR
1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).
2. Select channel 3 on your TV.
3. Press PLAY.
¡ If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by pressing PLAY on the VCR for 3 seconds during playback.
¡ There is case that the RF output channel does not change by situation (For example, when you adjust tracking using
CHANNEL ( ) ).
In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds.
¡ If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF output channel setting will return to CH3.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV WITH A/V TERMINALS
Antenna/Cable signal
A/V-compatible or wide screen TV
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
ANT-OUT
R
VIDEO OUT VIDEO IN
R
To ANT. IN of TV
To VIDEO INPUT jack To VIDEO OUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks To AUDIO OUT jacks
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
[Fig. 1]
Notes
¡ Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a
VCR first, picture may be distorted due to the copy protection system.
– 13 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 14
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR
COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNIT. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION
UNIT, you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBINA-
TION UNIT and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect the supplied RF cable, see page 13.
A/V-compatible or wide screen TV
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
R
ANT-OUT
VIDEO OUT VIDEO IN
R
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
To S-VIDEO INPUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
To S-VIDEO OUT jack
To AUDIO OUT jacks
[Fig. 2]
FOR TVs WITH COMPONENT VIDEO IN JACKS
Use a component video cable (commercially available) in place of the yellow DVD/VCR video cable and S-
VIDEO jack to enjoy higher quality pictures.
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBI-
NATION UNIT. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBI-
NATION UNIT, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the
DVD/VCR COMBINATION UNIT and the TV’s Antenna In jack, or connect the yellow VCR video cable as described earlier (Fig. 1). To connect the supplied RF cable, see page 13.
To Right (red) and Left (white)
AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUTPUT jacks
A/V-compatible or wide screen TV
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
R
ANT-OUT
VIDEO OUT VIDEO IN
R
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
To COMPONENT VIDEO
INPUT jacks
To COMPONENT VIDEO
OUT jacks
[Fig. 3]
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
(Stereo Receiver)
Amplifier equipped with digital input jacks, MD deck,
DAT deck, etc.
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
R
ANT-OUT
VIDEO OUT VIDEO IN
R
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
To COAXIAL DIGITAL AUDIO INPUT jack
To COAXIAL DIGITAL
AUDIO OUT jack
[Fig. 4]
Notes
¡ The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital
¡ sound by an MD or DAT deck.
Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a DVD disc using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY DIGITAL to OFF.)
– 14 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 15
CONNECTING TO A RECEIVER WITH DOLBY DIGITAL DECODER
If using this DVD/VCR COMBINATION UNIT to play a DVD disc in 5.1 channel Dolby Digital surround, the
DVD/VCR COMBINATION UNIT outputs a Dolby Digital data stream from its COAXIAL DIGITAL AUDIO
OUT jack. By hooking the DVD/VCR COMBINATION UNIT up to a Dolby Digital receiver, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as heard in movie theaters.
Use an audio coaxial digital cable (commercially available) for the audio connections.
Front speaker
(left)
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
R
ANT-OUT
VIDEO OUT VIDEO IN
R
Center speaker
Front speaker
(right)
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
DVD
AUDIO OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
R
COAXIAL
To COAXIAL DIGITAL
AUDIO OUT jack
Surround speaker
(left)
Receiver with
Dolby Digital Decoder
Surround speaker
(right)
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
[Fig. 5]
¡ If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to ON for audio output in the setup mode.
¡ Unless connected to a Dolby Digital receiver, set DOLBY DIGITAL to OFF for audio output in the setup mode.
Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
CONNECTING TO AN ANALOG AUDIO SYSTEM
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L
To AUDIO OUT jacks
L
S-VIDEO
OUT
COMPONENT
DVD
DVD
Y
DIGITAL
AUDIO OUT
R
ANT-OUT
VIDEO OUT VIDEO IN
R
Cb
Cr
L
COAXIAL
R
Stereo system
To Right (red) and Left (white)
AUDIO INPUT jacks or
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
ANALOG AUDIO OUT jacks
Notes
¡ Be sure to turn off the power to all components in the system before connecting another component.
[Fig. 6]
¡ Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR
COMBINATION UNIT.
– 15 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 16
SETUP
AUTOMATIC CHANNEL SET UP
VCR
You can automatically program the tuner to scan only the channels you receive in your area.
¡ Channel memory programming is NOT needed when you connect the VCR to a cable box or a satellite box as in "CONNECTING TO A TV WITHOUT
A/V TERMINALS" on page 13. In this case, select channel 3 on your TV. Then, the channel you want to record or view may be selected at the cable box or satellite box.
¡ If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV.
¡ Follow the steps below once. Repeat only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.)
¡ You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing
CLEAR/C.RESET.
1 You need to connect the antenna or cable to the VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet.
6 After scanning, the tuner stops on the lowest memorized channel. The TV screen returns to TV mode.
¡ If “AUTO SET UP” appears on the TV screen again, check the cable connections. Press B once again and the VCR will begin preset again.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHAN-
NEL (o/p) or by directly pressing Number on the remote control.
Note for using the Number:
¡ When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7)
¡ You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
TO PRESET THE CHANNELS AGAIN
1 Press MENU until the main menu appears.
(If you have already set the clock, you only have to press it once. If not, you have to press it twice).
2 Select “CHANNEL SET UP” by pressing K
or L. Then, press B. 2
Turn on the TV and set the TV to channel 3.
¡ If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail.)
3 Select “AUTO SET UP” by pressing K or L.
Then, press B.
¡ After scanning, the tuner stops on the lowest memorized channel.
3 Turn on the VCR by pressing POWER. the
POWER light will come on.
4 Select the On Screen Language (“ENG-
LISH”, “FRANCAIS” or
“ESPAÑOL”) by pressing K
or L. Then, press B.
5 Begin channel preset by pressing B once.
The tuner scans and memorizes all active channels in your area.
CH 01
¡ The VCR distinguishes between standard TV channels and cable channels.
AUTO SET UP
– 16 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 17
TO ADD/DELETE CHANNELS
When scanning, some channels may be skipped due to a weak signal. In such cases, you can add the channels to the VCR memory manually.
1
2
Press MENU until the main menu appears.
(If you have already set the clock, you only have to press it once. If not you have to press it twice).
- MENU -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
[ON]
Select "CHANNEL SET UP" by pressing K
or L. Then, press B.
CLOCK SET UP
VCR
1 Select main menu by pressing MENU.
¡ If the clock is not set, the CLOCK SET menu appears first. In this case, follow step [3].
2 Select "CLOCK SET" by pressing K or L.
Then, press B.
3 Set the clock.
3
Select "MANUAL SET UP" by pressing K or
L . Then, press B.
1) Set the month
Press K or L repeatedly.
Then, press B.
4 Enter the desired channel number by press-
ing K or L.
2) Set the day
Press K or L repeatedly.
Then, press B.
5
Add or Delete it from memory by pressing
B or s so that "ADD" or "DELETE" flashes on the TV screen accordingly.
6 Exit the Preset mode by pressing
CLEAR/C.RESET.
3) Set the year
Press K or L repeatedly.
Then, press B.
The day of the week will appear automatically.
4) Set the hour
Press K or L repeatedly.
Then, press B.
TO CHANGE THE ON-SCREEN
LANGUAGE
VCR
5) Set the minute
Press K or L repeatedly.
Then, press B.
1 Press MENU twice to call up the main menu. (If you have already set the clock, you only have to press it once).
6) Set AM or PM
Press K or L repeatedly.
2
Select "LANGUAGE SELECT" by pressing K
or L. Then, press B.
3 Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing K or L. Then, press
CLEAR/C.RESET.
¡ If you accidentally select Spanish or French and need English: Press MENU and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press B, and select ENGLISH by pressing
K or L .
Finally, press CLEAR/C.RESET.
¡ To go back one step, press s.
4
Start the clock by pressing
CLEAR/C.RESET or B.
CLOCK SET
MONTH DAY YEAR
03 / 17 MON 2003
HOUR MINUTE AM/PM
05 : 40 PM AM
PM
– 17 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 18
PLAYBACK FUNCTION
NORMAL PLAYBACK
2 Select "AUTO REPEAT" by pressing K or L.
VCR
1 Insert a prerecorded tape. The VCR will turn on.
¡ If the safety tab has been removed, the
VCR will start playback automatically.
3
Begin auto repeat playback by pressing B so that ON appears next to "AUTO
REPEAT".
¡ If the on-screen menu still remains, CLEAR/C.RESET
¡ to exit the menu.
To cancel the Auto repeat mode, press B at step [3] so that OFF appears next to "AUTO REPEAT".
2 Turn on the TV and set the TV to channel 3.
¡ If noise appears, change the RF output channel of the
VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See “RF OUTPUT CHANNEL” on page 13 for the detail.)
3 Begin playback by pressing PLAY.
¡ Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH. on the remote or CHANNEL (o/p) on the VCR.
¡ When a tape has reached the end, the VCR will rewind the tape to the beginning, and eject the tape.
4 To stop playback, press STOP.
¡ If no corresponding symbols appear on the display when you press buttons such as PLAY, RECORD,
D or E, that means no cassette tape is in the
VCR. Please insert a tape.
SEARCH FUNCTIONS
VCR
PICTURE SEARCH
If you want to skip or repeat a scene during playback, press D or E.
¡ Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only).
INDEX SEARCH
An index mark will be assigned at the beginning of each recording you made. You may skip to a specific marked point by following the steps below.
1 Press SEARCH MODE so that the Index
Search menu appears.
2 Enter the number of recordings you wish to
skip by pressing K or L within 30 seconds.
INDEX SEARCH
03
Counter Reset
¡ You can reset the counter by pressing
CLEAR/C.RESET on the remote control twice.
STILL/SLOW
You can freeze the picture on TV screen by pressing
PAUSE during playback.
¡ You can advance the picture one frame at a time by
¡ pressing PAUSE during the Still mode.
You cannot manually adjust the tracking of a still picture. However, if the picture begins to vibrate vertically during the still mode, you can stabilize the
¡ picture by pressing CHANNEL (o/p).
If the picture is distorted or rolling vertically, adjust
¡ the vertical hold control on your TV, if so equipped.
You can watch in the slow motion by pressing
¡
SLOW during playback or the still mode.
If a noise bar appears on the TV screen, you can
¡ reduce it by pressing CHANNEL (o/p).
After the VCR has been in Still/Slow mode for 5 minutes, it will stop automatically to protect the tape
¡ and the video head from damage.
To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
VCR
This feature allows you to play a tape over and over.
3 Press B or { to start index search.
¡ If you want to go in the forward direction, press B .
¡ If you want to go in the reverse direction, press { .
¡ If you want to stop search function, press STOP.
¡ After index search, the VCR will play the tape automatically.
TIME SEARCH
This feature allows you to go to a specific point on a tape by entering the exact amount of time you wish to skip in order to reach the point.
1 Press SEARCH-MODE so that the Time
Search menu appears.
2 Enter your desired time to
skip by pressing K or L within 30 seconds.
TIME SEARCH
2 : 50
3 Press B or { to start time search.
¡ If you want to go in the forward direction, press B .
¡ If you want to go in the reverse direction, press { .
¡ If you want to stop search function, press STOP.
¡ After time search, the VCR will play the tape automatically.
1
Select main menu by pressing MENU.
– 18 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 19
RECORDING FUNCTION
VCR
OTR (One Touch Recording)
VCR It may be UNLAWFUL to record copyrighted material without the consent of the copyright owner.
Accidental Erasure Prevention
To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the hole with cellophane tape.
Before recording, make sure:
Record safety tab
¡ The desired channel is selected by pressing Number on the remote control or CHANNEL (o/p). (If you connected the VCR to a cable box or satellite box as in "CONNECTING TO A TV WITHOUT A/V
TERMINALS" on page 13, select channel 3 on your
TV, and select the specific INPUT channel assigned by your cable box or your satellite box on the
DVD/VCR COMBINATION UNIT. Then, select the channel you want to record with the cable box or the satellite box. In this case, you can ONLY record and view the SAME channel.)
¡ If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV.
¡ There is a tape with a safety tab in the VCR.
¡ The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing SPEED on the remote control.
This feature allows you to set the recording length simply by pressing REC/OTR on the VCR.
1 Press REC/OTR to begin OTR. The TIMER
REC light comes on. Change the recording length by pressing REC/OTR repeatedly.
REC OTR(0:30) OTR(1:00).....
(Normal recording)
OTR(8:00) OTR(7:30)
¡ If a tape ends during OTR, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. (If the DVD power is off, the VCR will become STANDBY status).
¡ When OTR is finished , the VCR turns off automatically. To use the VCR again, press T-SET on the remote, or STOP/EJECT on the DVD/VCR COM-
BINATION UNIT.
TIMER RECORDING
VCR
Tape Speed Recording/Playback Time
Type of tape
SP mode
SLP mode
T60
1 hour
3 hours
T120
2 hours
6 hours
T160
2-2/3 hours
8 hours
Note
¡ You can not copy a DVD to a videotape.
NORMAL RECORDING
You may set the VCR to start recording while you are away. You can set eight programs to record on specific days, daily or weekly within 1 year period.
If you have not yet set the clock, "CLOCK SET" appears. If so, follow the steps [3] and [4] in
"CLOCK SET UP" section on page 17. Then, set the timer recording.
1 Insert a tape with its safety tab into the
DVD/VCR COMBINATION UNIT.
VCR
1 Begin the recording by pressing RECORD.
The REC Light comes on.
¡ To temporarily stop recording or to resume it, press
PAUSE. After the VCR has been in Pause mode for
5 minutes, it will stop automatically to protect the tape and the video head from damage.
2 Press STOP when the recording is completed.
Note
¡ When you wish to watch another program while recording, select desired channel on your TV. If noise appears press VCR/TV.
¡ This is not possible when using a cable box or satellite box.
2 Select main menu by pressing MENU.
3 Select "TIMER PROGRAM-
MING" by pressing K or L.
Then, press B. The set up screen is displayed.
4 Set the timer.
¡ To go back one step, press s.
TIMER PROGRAMMING
PROG 12345678
DATE -
START TIME
END TIME
CHANNEL
REC SPEED
1) Set the program number (1-8)
Program number which is not set up flashes. Press K or L repeatedly for the desired program number.
Then, press B.
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
– 19 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 20
2) Set the frequency of the recording
For once: Press K or L to point to
"ONCE".
For daily (Monday~Friday): Press K or L to point to "DAILY".
For weekly: Press K or L to point to "WEEKLY".
Then, press B.
PROGRAM NUMBER 4
ONCE
DAILY
WEEKLY
3) Set the date
First, press K or L for the month.
Then, press B. Next, press K or
L for the day. Then, press B.
5) Set the end time
Follow the instructions of
"Set the start time" to set the end time.
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
4) Set the start time
First, press K or L for the hour.
Then, press B. Next, press K or L
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - for the minute. Then, press B. And then, press K or L for AM or PM. Then, press B.
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
¡ If a tape ends during TIMER RECORDING, the
VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks.
(If the DVD power is off, the VCR will become
STANDBY status).
¡ If a tape is not in the VCR or does not have a safety tab, the TIMER REC light flashes and timer recording will not operate. Please insert a recordable tape.
¡ When all timer recordings are finished, the TIMER
REC light will flash. To use the VCR again as usual, press T-SET to disable the flashing TIMER REC light, then press VCR/TV to select the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.
¡ When timer recordings are set, the TIMER REC light will come on. To use the VCR as usual until the time for the recording, press T-SET so that TIMER REC light disappears. Press VCR/TV to choose the VCR position.
Select either VCR or DVD mode, then continue with the other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the
TIMER REC light is on or flashes.
¡ You can use the DVD player while the TIMER REC light is on or flashes, or during a timer recording.
Press POWER to turn on the DVD. Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t have to set the TIMER off to use the
DVD only.
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press STOP/EJECT on the DVD /VCR COMBINA-
TION UNIT.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
6) Set the channel number
Press K or L repeatedly for the desired channel number. Then,
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL - -
REC SPEED - press B.
If you connected the DVD/VCR COMBINATION UNIT to a cable box or satellite box as in "DVD/VCR TO TV
CONNECTION" on page 13, select the DVD/VCR to channel 3 or 4 the same channel as RF output channel of the DVD/VCR.
Then, select the channel you want to record with the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
7) Set the tape speed
Press K or L repeatedly for the desired tape speed. Then, press B.
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL 1 6
REC SPEED SP
SP
SLP
1 Press T-SET.
¡ If the DVD output mode is selected, you have to switch it to the VCR mode by pressing the VCR on the remote control or the OUTPUT on the VCR.
2 Select main menu by pressing MENU.
5 To set another program, repeat step [4]. To exit, press CLEAR/C.RESET.
3 Select "TIMER PROGRAMMING" by press-
ing K or L. Then, press B.
6
Press T-SET to set the timer.
¡ The TIMER REC light on the DVD/VCR COMBI-
NATION UNIT comes on. TIMER RECORDING
WILL NOT BE ACTIVATED UNLESS YOU
PRESS T-SET.
HINTS FOR TIMER
RECORDING
4 Select the program number you want to
check by pressing K or L.
¡ The details of the selected program appears on the
TV screen.
¡ Go to the digit you want to change by pressing B or s . Then, enter correct numbers by pressing o or p.
¡ You may cancel the entire program by pressing s while the program number flashes.
VCR
¡ If there is a power failure or the VCR is unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
– 20 –
5 Press CLEAR/C.RESET to exit.
6 Press T-SET to return to timer stand-by mode.
EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 21
SPECIAL FEATURES
TO MONITOR THE RECORDING
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends or relatives for your enjoyment.
You can not copy a DVD to a videotape.
Warning:
Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect the recording VCR (this unit), the playing
VCR (another source) and your TV using the following diagram.
¡ You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back.
[Recording VCR]
(this unit)
DVD/VCR
ANT-IN
AUDIO OUT
L
VCR
AUDIO IN
L
R
ANT-OUT VIDEO OUT
R
VIDEO IN
Y
Cb
Cr
DVD
L
COAXIAL
R
VCR
1 Turn on the TV and set the TV to channel 3.
¡ If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel
(CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail).
2 Press VCR/TV on the recording VCR.
MTS (Multi-Channel Television
Sound) SYSTEM
VCR
When you play a VHS tape, or receive a broadcast on the VCR’s tuner, the current status will appear when you press
STOP 12:00AM
CH 32
STEREO
SAP DISPLAY on the remote control.
1)*
When you record a MTS broadcast signal, you need to set it to
MTS mode.
SP 0:00:00 HIFI
2)*
RF cable
(supplied)
[TV set]
(Use for monitoring)
Audio/Video cables
(not supplied)
ANT in
OUT IN
LEFT
RIGHT
AUDIO
VIDEO
[Playing VCR]
(another source)
1)* Press MENU and select "TV STEREO" or
"SAP" by pressing K or L. Then, press B to select mode. To exit, press
CLEAR/C.RESET.
¡ Although a program may be broadcast in both stereo and sub audio, you must select the Recording mode to TV STEREO or SAP before you record a broadcast.
1
Insert a pre-recorded tape into the playing VCR.
2 Insert a tape with a safety tab into the recording VCR.
3 Press SPEED on the recording VCR to select the desired recording speed (SP/SLP).
2)* Press MENU and select "AUDIO OUT" by
pressing K or L. Then, press B. Next,
select "HIFI" or "MONO" by pressing K or
L . To exit, press CLEAR/C.RESET.
¡ While the VCR is set in HIFI stereo mode, HIFI appears on the TV screen. While the VCR is set in monaural (MONO) mode, HIFI disappears from the
TV screen.
4 Select the “L1” or “L2”position on the recording VCR.
¡ When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons (o/p).
¡ When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons (o/p).
5 Press REC/OTR on the recording VCR.
6 Begin playback of the tape in the playing
Bilingual broadcast
VCR.
¡ For best results during dubbing, use the VCR’s front panel controls whenever possible. The remote con-
¡ trol might affect the playing VCR’s operation.
Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
*
¡ recommended.
You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR.
– 21 –
Stereo &
Bilingual broadcast
MTS RECORDING/MONITOR MODE
Type of broadcast
Display on the
TV screen
STEREO/SAP
Selection
Hi-Fi audio track
(2-channel)
L-channel R-channel
Normal audio track
Regular
(monaural audio)
-None-Invalid-
Mono Mono Mono
Stereo broadcast
STEREO L R L+R
SAP
STEREO
SAP
TV STEREO*
SAP*
TV STEREO*
SAP*
Main audio program
Sub audio program
L
Sub audio program
Main audio program
Sub audio program
R
Sub audio program
Main audio program
Sub audio program
L+R
Sub audio program
EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 22
AUTO REWIND
When a tape reaches the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the
VCR will eject the tape and switch itself off.
¡ The VCR will not rewind the tape automatically during timer recording or One Touch Recording.
REAL TIME TAPE COUNTER
¡ This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change during blank portions of the tape.)
¡ The indication will appear when the tape is rewound further than “0:00:00” on the tape counter.
PLAYING A DISC
BASIC PLAYBACK
DVD-V CD
Getting started
¡ Turn on the power of the TV, amplifier and any other components which are connected to the DVD.
¡ Make sure the TV and audio receiver (commercially available) are set to the correct channel.
¡ Select DVD mode by pressing DVD on the remote control or output on the front panel.
Notes
¡ A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.
¡ With DVDs that use titles for playback program signals, playback may start from the second title, or it may skip these titles.
¡ During the playback of a two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.
1 Press POWER.
¡ “Load” will appear briefly on the display panel.
2 Press OPEN/CLOSE to open disc loading tray.
3 Place the chosen disc in the tray, with the label facing up.
GENERAL FEATURES
DVD may contain menus to navigate the disc and access special features. Press the appropriate Number buttons or use Arrow (L/K/s/B) to highlight your selection in the DVD main menu and press ENTER to confirm.
Note
¡ Unless stated, all operations described are based on remote control use. Some operations can be carried out using the menu bar on the TV screen.
PAUSE
4
Press PLAY.
¡ The tray will close automatically, and playback will then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
¡ When you playback the DVD which a title menu is recorded, it may appear on the screen. In this case, refer to “TITLE MENU” on page 23.
2
DVD-V
1
During playback, press PAUSE.
¡ Playback will pause and sound will be muted.
To continue playback, press PLAY.
CD
5 Press STOP to stop playback.
– 22 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 23
DISC MENU RESUME
DVD-V DVD-V CD
1 Press MENU.
¡ The DVD main menu will appear.
2 If the feature is not available, may appear on the TV screen.
symbol
1 During playback, press STOP.
¡ Resume message will appear on the TV screen.
2 Press PLAY, playback will resume from the point at which playback was stopped.
¡ To cancel resume, press STOP twice.
3 If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.
FAST FORWARD/REVERSE
SEARCH
DVD-V CD MP3
4 Press Arrow (L/K/s/B) to select an item, and ENTER to confirm selection.
TITLE MENU
1
Press TITLE.
¡ The title menu will appear.
2
If the feature is not available, may appear on the TV screen.
DVD-V
1 During playback, press g or h repeatedly to select the required forward or
¡ reverse speed: x2, x8, x50, x100.
For audio CDs, the speed is fixed at
×16.
¡ For MP3, the speed is fixed at
×8.
2 To return to normal playback, press PLAY.
symbol
SLOW FORWARD /
SLOW REVERSE
DVD-V
3 Press Arrow (L/K/s/B) to select an item, and ENTER to confirm selection.
1 During playback, press PAUSE.
2 Press g or h .
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡ Press MENU to call up the DVD menu.
¡ Press TITLE to call up the title menu.
Note
¡ Contents of menus and corresponding menu operations may vary between discs. Refer to the manual accompanying the disc for details.
3 Press g or h repeatedly to select the required speed: 1/16, 1/8, 1/2 of the normal playback.
4 To return to normal playback, press PLAY.
STEP BY STEP PLAYBACK
DVD-V
1
During playback, press PAUSE.
¡ Playback will pause and sound will be muted.
2
The disc goes forward by one frame each time PAUSE is pressed.
3
To exit step by step playback, press PLAY.
– 23 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 24
1
ZOOM
¡ Playback will continue.
2
Press ZOOM during playback.
Press ZOOM repeatedly to select the required zoom factor: x2, x4 or OFF.
DVD-V
The Zoom function allows you to enlarge the video image and to pan through the enlarged image.
Using SKIP H G
During playback, press SKIP G to move the next track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current track. Press it repeatedly to go to the previous tracks.
¡ Track number will appear briefly on the DVD/VCR
COMBINATION UNIT display panel.
¡ If SKIP is pressed while the playback is paused, the playback will be paused again after skipping to the next track.
Note
¡ SKIP H G are not available when playback is stopped.
3 Use the Arrow ( K / L / s / B ) to move the zoomed picture across the screen.
4 To exit zoom mode, press ZOOM to OFF.
Notes
¡ Zooming function does not work while disc menu is shown.
¡ x4 zoom is not available on some discs.
TITLE / CHAPTER SEARCH
DVD-V
1 Press SEARCH MODE once for the Chapter search, twice for the Title search during playback.
/2
TRACK
CD
There are three ways to begin playback on an Audio
CD at a specific Track.
Using the Number buttons
1 Press the Number buttons to enter the desired Track number.
¡ Playback will start at the selected track.
¡ For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡ To play track 26, press +10, 2, 6 on the Number buttons.
Using SEARCH MODE
1 Press SEARCH MODE.
¡ The track search display appears.
2 Within 30 seconds, select a desired track number using the Number buttons.
¡ For single digits press 0 first.
¡ Playback will start at the selected track.
2 Enter the desired chapter/title number using the Number buttons.
¡ Playback will start at the selected Chapter or Track.
¡Press CLEAR to erase the incorrect input.
¡ For single digits press 0 first.
TIME SEARCH
1 During playback, press SEARCH MODE three times (CD: twice) to display the Time
Search on the TV screen.
DVD-V CD
2 Within 30 seconds, enter a desired disc time using the Number buttons.
¡ Playback will start at the specified time.
¡ Press CLEAR to erase the incorrect input.
– 24 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 25
REPEAT
REPEAT is available only during playback.
REPEAT TITLE / CHAPTER
DVD-V
PROGRAM
CD
You may determine the order in which tracks will play.
To activate the repeat function, press REPEAT during playback.
¡ The repeat mode changes as described below every time you press the button.
CHAPTER TITLE
(current chapter repeat) (current title repeat)
OFF
(repeat off)
1 In stop mode, press MODE.
¡ The PROGRAM screen will appear.
2 Press ▲ or ▼ to select a track, then press
ENTER.
¡ Press CLEAR to erase the most recently entered program.
CD [AUDIO] TOTAL 0:03:30
Notes
¡ Repeat Title/Chapter is not available with some scenes.
¡ The REPEAT setting will be cleared when moving to other title or chapter.
REPEAT TRACK
CD
To activate the repeat function, press REPEAT during playback.
¡ The repeat mode changes as described below every time you press the button.
TRACK
(current track repeat)
ALL
(entire disc repeat)
OFF
(repeat off)
Notes
¡ Track Repeat setting will be cleared when moving to other track.
¡ Repeat playback does not function during repeat A-
B playback.
REPEAT A-B
DVD-V CD
3 Press PLAY to play the programmed tracks.
Notes
¡ While the program is being played back, the STOP works as follows.
¡ Press STOP once and then PLAY again, playback will restart from the point where STOP was pressed.
(Program continued)
¡ Press STOP twice and then PLAY again, playback will restart from the track in the usual way. (Program cleared)
¡ Up to 99 programs can be entered.
¡ If you like to repeat the current track in the program, press REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire program press REPEAT repeatedly until ALL appears during playback.
¡
1 Press REPEAT A-B at your chosen starting point.
A- appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen
¡ end point.
A-B appears briefly on the TV screen, and the repeat sequence begins.
3 To exit the sequence, press REPEAT A-B.
Notes
¡ The repeat A-B section can only be set within the current title (for DVDs), or current track (for audio
CDs).
¡ Repeat A-B is not available with some scenes in
DVD.
¡ To cancel the A point which was set, press CLEAR.
¡ Repeat A-B playback does not function during title, chapter, track or all repeat playback.
– 25 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 26
RANDOM PLAYBACK
This shuffles the playing order of tracks instead of playback in the sequence.
1 In stop mode, press MODE twice.
¡ RANDOM screen appears.
RANDOM
CD
CD [AUDIO] TOTAL 0:45:55
Notes
¡ Folders are known as Groups; files are known as
Tracks.
¡ MP3 files are accompanied by
3 icon.
¡ Maximum of 255 folders can be recognized.
¡ Maximum of 256 files can be recognized.
¡ Up to 8 hierarchies can be created.
This player recommends the use of files recorded at the below specifications:
¡ Sampling frequency: 44.1kHz or 48kHz
¡ Constant bit rate: 112kbps ~ 320kbps.
RANDOM PROGRAM
--no indication--
PLAY
ON-SCREEN INFORMATION
MP3
You can check the MP3 files during playback.
2 Press PLAY to start random playback.
Note 1 Press DISPLAY.
¡ If you like to repeat the current track in the random selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
¡ The name of the file currently in play will be displayed.
repeat the entire random selection press REPEAT repeatedly until ALL appears during playback.
2 Press DISPLAY again to show the track number, the repeat status, and the playback status at the top of the screen.
MP3 PLAYBACK
¡ will be displayed when repeat play has been selected.
MP3
T - indicates Track repeat
When a CD with MP3 files is inserted in the
DVD/VCR, the MP3 menu will appear on the TV screen, and number of tracks is displayed on the front panel.
G - indicates Group (folder) repeat
A - indicates Disc repeat
3 Press DISPLAY again to exit.
1 In stop mode, press Arrow ( K / L ) to select the desired group track.
¡ If a group is selected, press
B or ENTER to go on to the track selection screen. Press Arrow (
K
/
L
) to choose a track, then press
B or ENTER.
¡ If a track is selected, press
B or ENTER to start playing tracks. Starting from the one you’ve just chosen the subsequent tracks will be played.
¡ Choose FIRST PLAY to start playback from the beginning of the listed tracks.
¡ Press TITLE to return to the first item.
2 Press STOP to stop playback.
TRACK SELECTION
MP3
1 Press SEARCH MODE during playback.
¡ The FILE LIST will appear.
2 Select a desired track using Arrow
( K / L /s/B ).
¡ Press
B when you want to go to the next hierarchy.
¡ Press s when you want to go back to the previous hierarchy.
3 Press PLAY to start playing.
Notes
¡ Press SEARCH MODE to exit.
¡ Some selections may take a while to be recognized.
– 26 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 27
RANDOM PLAYBACK
MP3
SUBTITLE LANGUAGE
DVD-V
1 Press MODE twice while playback is stopped.
The DVD allows you to select a language for subtitles during DVD disc (if available) playback.
2 Press PLAY to play the tracks in random order.
PROGRAM
MP3
1 Press SUBTITLE during playback.
2 Press SUBTITLE repeatedly to select your desired subtitle language.
¡ The subtitle language will be displayed on the display bar at the top of the screen.
This feature allows you to program a mp3 disc to play in a desired sequence.
1 Press MODE during playback is stopped.
¡ The PROGRAM screen will appear.
2
Press Arrow ( K / L ) to select a track, then press ENTER, to save it in a program.
¡ Press CLEAR to erase the incorrect input.
3
Press PLAY to start programmed playback.
AUDIO LANGUAGE
DVD-V
3 To turn off subtitles, press SUBTITLE repeatedly until OFF appears.
Notes
¡ Pressing AUDIO may not work on some DVDs with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).
¡ Some discs allow audio language setting/subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)
¡ If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have subtitles in that language.
¡ If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead.
(Refer to page 31.)
The DVD/VCR allows you to select a language during
DVD disc (if multi language available) playback.
CAMERA ANGLE
1 Press AUDIO during playback.
DVD-V
2 Press AUDIO repeatedly to select your desired language.
Some DVD discs contain scenes which have been shot simultaneously from various angles. You can change the camera angle when the ( ) icon appears on the screen.
STEREO SOUND MODE
CD
1
Press AUDIO repeatedly during playback to select between STEREO, L-CH or R-CH.
¡ STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Note
¡ If the Virtual Surround setting is ON, the sound mode will be fixed to STEREO, and can not be changed.
1 Press ANGLE during playback.
¡ The selected angle will be displayed on the display bar at the top of the screen.
2 Press ANGLE repeatedly to select your desired angle.
– 27 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 28
CHANGING THE ON-SCREEN
DISPLAY
DVD-V CD
PARENTAL CONTROL
DVD-V
You can check the information about the current disc by pressing DISPLAY on the remote control.
For DVD-Vs
1 Press DISPLAY during playback to show current Chapter.
¡ The elapsed and remaining playing time of the current chapter will be displayed.
9/49 0:00:00 -0:00:00
2 Press DISPLAY again to show current Title.
¡ The elapsed and remaining playing time of the current title will be displayed.
3 Press DISPLAY third time.
¡ The BIT RATE and the current repeat setting will be displayed.
¡ If you are playing a dual layered disc, the layer number will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
Parental Control limits the disc viewing that exceed your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alternative scenes from being played by your children.
PARENTAL LEVEL
Parental Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
3
Press Arrow ( s /B ) to select PARENTAL, then press ENTER.
PARENTAL
PARENTAL LEVEL ALL
4
Press DISPLAY the fourth time to remove the display.
4
Enter your four-digit password then press
ENTER.
5 Press Arrow ( K / L ) to select PARENTAL
LEVEL, then press ENTER.
For audio CDs
1 Press DISPLAY during playback, the current
Track will be displayed on the TV screen.
¡ The elapsed and remaining playing time of the current track will be displayed.
6 Press Arrow ( K / L ) to select the desired level.
2 Press DISPLAY again to show current Total
Track.
¡ The elapsed and remaining playing time of the current total track will be displayed.
3 Press DISPLAY third time to remove the display.
7 Press SETUP to exit
Notes
¡ When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the password. (in the event you forget the password, see below.)
¡ To change the password, press Arrow (K/L) to select CHANGE at step 5, then press ENTER. Enter the four-digit pass-word, then press ENTER.
¡ With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
¡ Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1 Press 4, 7, 3, 7 at step 4. Then enter your new password.
¡ Password will be cleared and parental level will be set to ALL.
2 Proceed the above Steps 5-7 again.
– 28 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 29
CONTROL LEVELS
¡ALL
All parental lock is cancelled.
¡Level 8
DVD software of any grade (adult/general/children) can be played back.
¡Levels 7 to 2
Only DVD software intended for general use and children can be played back.
¡Level 1
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.
2 Press Arrow (s/ B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- : - - : - -” appears in the display.
3 When reaches the desired point, press
ENTER.
¡ The Title or Track and elapsed playing time will appear in the TV screen.
MARKER SETUP SCREEN
DVD-V CD
Use markers to memorise your favorite places on a disc.
4 To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (s/ B) to choose the desired marker, then press ENTER.
Notes
¡ Opening the disc tray or turning off the power or select AC at step 2 and press ENTER will erase all
Markers.
¡ To clear a marker, using Arrow (s/ B), position the cursor on to the marker number to be cleared and press CLEAR.
¡ You can mark up to 10 points.
1 Press SEARCH MODE four times (CD: three times) during playback.
¡ The display screen and Markers will appear on the
TV screen.
5 Press SEARCH MODE or RETURN to exit.
DVD SETUP
AUDIO SETTING
Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
¡ CUSTOM mode will appear.
DOLBY DIGITAL: QUICK
Set to On when the unit is connected to a Dolby Digital
Receiver.
(ON: Outputs a Dolby Digital Signal)
(OFF: Convert the Dolby Digital to PCM (2channel))
¡ The default setting is ON.
DOWN SAMPLING:
¡ Set to ON when outputting in 48 kHz.
¡ The default setting is ON.
When playing disc with copyright Protection
¡ If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.
3
Press Arrow (s/ B) to select AUDIO, then press ENTER to confirm.
5 Press SETUP to exit.
AUDIO
DRC OFF
DOLBY DIGITAL ON
DOWN SAMPLING ON
4
Press Arrow ( K / L ) to select the below items, then press ENTER.
DRC (Dynamic Range Control):
¡ To compress the range of soft to loud sounds.
¡ The default setting is OFF.
– 29 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 30
BLACK LEVEL SETTING
DVD-V
DISPLAY SETTING
DVD-V
Adjust the Black Level Settings to make the black parts of the picture as bright as you preferred.
You can change certain aspects of the DVD display screens and on-screen messages.
1 Press MODE during playback.
2
ON
Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
¡ CUSTOM mode will appear.
3 Press Arrow (s/ B) to select DISPLAY, then press ENTER to confirm.
3 Press MODE twice or RETURN to exit.
DISPLAY
TV ASPECT
ANGLE ICON
4:3 LETTER BOX
ON
AUTO POWER OFF ON
VIRTUAL SURROUND
DVD-V CD MP3
You can enjoy stereophonic visual space on your existing stereo system.
1 Press MODE twice (CD/MP3: once) during playback.
OFF
2 Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
3 Press MODE or RETURN to exit.
Note (for CD play only)
¡ Virtual Surround will not be effective if the sound mode is set to something other than STEREO.
4 Press Arrow ( K / L ) to select the below items, then press ENTER.
TV ASPECT: QUICK
¡ Press Arrow (K/L) for an item selection, then press
ENTER.
¡ Select 4:3 LETTER BOX for a black bars appears on top and bottom of the screen.
¡ Select 4:3 PAN & SCAN for a full height picture with both sides trimmed.
¡ Select 16:9 WIDE if a wide-screen TV is connected to the DVD/VCR.
¡ The default setting is 4:3 LETTER BOX.
ANGLE ICON:
¡ Press ENTER repeatedly to turn Angle icon ON or
OFF.
¡ The default setting is ON.
AUTO POWER OFF:
¡ Press ENTER repeatedly to turn Auto Power off ON or OFF.
¡ The default setting is ON and it will turn the
DVD/VCR to off automatically after 35 minutes of no use.
5 Press SETUP to exit.
Notes
¡ Be sure to press SETUP, or the setting will not work.
– 30 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 31
LANGUAGE SETTING
DVD-V
Language options are not available with some discs.
1 Press SETUP in STOP mode.
AUDIO:
¡ Sets the audio language.
SUBTITLE:
¡ Sets the subtitle language.
DISC MENU:
¡ Sets the language for DVD menu.
PLAYER MENU: QUICK
¡ Sets the language for the On-screen display.
2 Press B to select CUSTOM, then press
ENTER.
¡ CUSTOM mode will appear.
3 Press Arrow (s/ B) to select LANGUAGE, then press ENTER to confirm.
5 Press Arrow ( K / L ) to select a setting, then press ENTER.
¡ If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list below.)
¡ Only the languages supported by the disc can be selected.
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ORIGINAL
OFF
ENGLISH
ENGLISH
4 Press Arrow ( K / L ) to select the next items, then press ENTER.
¡ If you want to return to LANGUAGE SETTING
MENU, press Arrow( s ).
6
Press SETUP to exit.
Note
¡ Language Setting for Audio and Subtitle is not avail able with some discs. Then use the AUDIO and the
SUBTITLE button. Details are on page 27.
Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
Code Language
5261
5256
5255
5264
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Code Language
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5861
5847
5868
5860
5866
5957
5953
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
Code Language
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
– 31 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 32
TROUBLESHOOTING GUIDE
If the DVD/VCR COMBINATION UNIT does not perform properly when operated as instructed in this
Owner's Manual, check the player consulting the following checklist.
D
V
D
V
C
R
V
C
R
D
V
D
PROBLEM CORRECTIVE ACTION
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The player does not respond to. • Check if the power plug is connected to an AC outlet.
the remote control.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote.
• You have to be within 23 feet of the player.
• Check if the correct mode is selected. If not switch the mode by pressing DVD or
VCR ,whichever you need, on the remote control.
• Check if a cassette tape is in the VCR.
Timer recording is impossible.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
Cannot go into Record mode.
• Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
Playback picture is partially noisy
• Put he player in VCR mode. Press VCR on the remote control so that the green VCR
OUTPUT light is lit.
• Adjust tracking control for a better picture by pressing CHANNEL ( ) on the
DVD/VCR COMBINATION UNIT.
Cannot view a tape but the audio is OK.
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
No, or poor, playback picture.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen • Re-check the ANT. IN and ANT. OUT connections. See page 13.
normally.
• Press VCR/TV.
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR
OUTPUT light is lit. Then, set it to the TV position by pressing VCR/TV.
Video or color fades in and out • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.
Cannot remove the tape.
No picture.
Disc cannot be played.
• Check if the player is in the VCR mode. If not, press VCR on the remote control to switch the mode.
• Connect the video cables firmly.
• Insert a correct video disc that plays on this player.
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other
DVD feature.
• Insert the disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
No sound.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This player does not support DTS audio. This is not a malfunction.
No DTS audio is output.
Distorted picture.
• Connect the player directly to the TV.
• There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language does not match the set up
• The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The camera angle cannot be • The DVD does not contain sequences recorded from different camera angles.
changed This is not a malfunction
Audio or subtitle language cannot be changed
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.
screen, prohibiting an operation This is not a malfunction.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡ Playback from a desired track and random playback are not available during program playback.
– 32 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 33
MAINTENANCE
SERVICING
¡ Should your DVD/VCR COMBINATION UNIT become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-968-3429 to locate an
Authorized Service Center.
CLEANING THE CABINET
¡ Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
¡ When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular motion.
¡ Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.
CLEANING THE DISC LENS
¡ If the player still does not perform properly when it is operated while referring to the relevant sections and to “TROUBLESHOOTING GUIDE” in this
Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
¡ Use discs which have the following logos on them.
(Optical audio digital discs.)
AUTO HEAD CLEANING
¡ Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
¡ Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR
COMBINATION UNIT may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429 to locate an Authorized Service Center.
NOTES:
¡ Remember to read the instructions included with the video head cleaner before use.
• Clean video heads only when problems occur.
Recordable ReWritable
¡ Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
¡ Always store the disc in its protective case when it is not used.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
– 33 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 34
Product type:
Discs:
Converter output:
Power source:
Power consumption:
Operating temperature:
Dimensions:
Weight:
SPECIFICATIONS
DVD player with Video Cassette Recorder
DVD video
Audio CD
Video Cassette tape
VHF Channel 3 or 4.
120 V AC +/- 10%, 60 Hz +/- 0.5%
24 W (standby: 7.0 W)
5°C to 40°C
W 17-1/8” (435 mm)
H 4” (99 mm)
D 8-7/10” (218 mm)
8.8 lbs (3.7 kg)
¡ Designs and specifications are subject to change without notice.
¡ If there is a discrepancy between languages, the default language will be English.
– 34 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 35
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
PANEL DELANTERO
1 2 3 4 5 6 7 8
OPEN/CLOSE
POWER
CHANNEL STOP/EJECT
PLAY
DVD
STOP PLAY
DVD
DVD
OUTPUT
VCR TIMER REC REC
VCR
REW F.FWD
VIDEO L AUDIO R
PANEL REMOTO
22
21
20
23 52
POWER SPEED AUDIO
24
1 2 3
51
SKIP/CH.
25
27
26
4
7
5
8
DISPLAY
0
DVD
PLAY
6
9
+ 10
VCR
VCR/TV
SLOW
PAUSE
50
49
48
47
46
45
29
28
STOP
RECORD
30
31
32
33
34
35
37
36
MENU
SETUP TITLE
MODE ZOOM
SEARCH
MODE
CLEAR/
C.RESET
SUBTITLE ANGLE REPEAT A-B
T-SET
ENTER
RETURN
43
44
42
41
39
40
38
1.
Bandeja de carga del disco
2.
Botón OPEN/CLOSE
Presione para insertar discos en o removerlos de la bandeja de disco.
3.
Luz DVD OUTPUT (verde)
Esta luz aparece cuando el DVD/VCR está en modo
DVD. Usted sólo puede mirar DVDs cuando la Luz
DVD OUTPUT verde está encendida. Para hacer que la Luz DVD OUTPUT verde se encienda, presione el
Botón DVD en el control remoto o el Botón OUTPUT en el panel delantero.
4.
Luz VCR OUTPUT (Verde)
Esta luz aparece cuando el DVD/VCR está en el modo
VCR. Usted puede sólo mirar cintas cuando la Luz
VCR OUTPUT verde está encendida. Para hacer que la
Luz VCR OUTPUT verde se encienda, presione el
Botón VCR en el control remoto o el Botón OUTPUT en el panel delantero.
5.
CASSETTE COMPARTMENT
6.
Botón POWER
Presione para conectar y desconectar la alimentación.
7.
Luz POWER
Se enciende cuando la alimentación está conectada.
8.
Botón STOP/EJECT (VCR)
● Botón de expulsión
Púlselo para sacar el videocasete de la
● videograbadora.
Botón Stop
Presione detener el movimiento de la cinta.
– 35 –
19 18 16 14 12 10
17 15 13 11 9
9.
Botón PLAY (VCR)
Presione para comenzar reproducción.
10.
Botones CHANNEL
En el modo VCR, presione para cambiar canales TV en el DVD/VCR; presione para ajustar el seguimiento durante reproducción de movimiento normal o lento; presione para remover fluctuaciones verticales en una imagen fija.
11. T omas AUDIO IN
Conecte aquí cables de audio procedentes de las tomas de salida de audio de un camcorder, otro VCR o una fuente de audio.
12.
Toma VIDEO IN
Conecte aquí un cable de videó procedente de la toma de salida de videó de un camcorder, otro VCR o una fuente de videó (reproductor de discos láser, camcorder, etc.).
13.
Botón F.FWD (VCR)
Presione para avanzar rápidamente la cinta o ver la imagen rápidamente en avance durante reproducción.
(Búsqueda en Avance).
14.
Botón REW (VCR)
Presione para rebobinar la cinta o para ver la imagen rápidamente en inversión durante el modo de reproducción.(Búsqueda en Rebobinado).
15.
Botón REC/OTR
Presione una vez para iniciar una grabación. Presione repetidamente para iniciar un Grabación de Un-Toque.
16.
Luz REC
Se enciende durante la grabación.
17.
Luz TIMER REC
Esta luz brilla cuando el DVD/VCR está en el modo espera o apagada para una grabación con temporizador o durante una grabación de Un-Toque, Parpadea si se presiona Botón T-SET para una grabación con temporizador, pero no hay cinta en el DVD/VCR.
Parpadea cuando todas las grabaciones con temporizador o grabaciones de Un-Toque han terminado.
18.
Botón OUTPUT
Presione para seleccionar el modo DVD o el modo
VCR.
●
Usted puede cambiar el modo de salida ya presionando el Botón OUTPUT en el panel delantero o ya presionando el Botón DVD o VCR en el control remoto. Sin embargo, si usted presiona el Botón
OUTPUT en el panel delantero primero, usted necesita volver a seleccionar el modo correspondiente presionando el Botón DVD o el
Botón VCR en el control remoto.
19.
Ventanilla de Sensor Remoto
20.
Visualización
SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 36
21.
Botón PLAY (DVD)
Comienza la reproducción del contenido del disco.
22.
Botón STOP (DVD)
Detiene la operación del disco.
23.
Botón SPEED
Presiona para seleccionar la velocidad de grabación de
VCR (SP o SLP)
24.
Botón POWER
Presione para conectar y desconectar la alimentación.
25.
Botones numéricos
●
Modo DVD
Presiónelos para seleccionar elementos numerados en un menú.
+10
Use este botón para ingresar números inguales o mayores que 10.
● Modo VCR
Presione para seleccionar canales de TV en el
DVD/VCR. Para seleccionar canales, entre números de canal como un número de dos dígitos para los resultados más rápidos. Por ejemplo, para seleccionar canal 6, presione 0.6.
26.
Botón DISPLAY
●
Modo DVD
Presione para tener acceso o remover la pantalla de visualización durante reproducción DVD o CD de audio.
●
Modo VCR
Presione para tener acceso o remover visualización de estado en pantalla de VCR.
27.
Botón DVD
Presione antes de utilizar el control remote para funciones DVD.
●
Usted puede cambiar el modo OUTPUT presionando
OUTPUT en el panel delantero o presionando DVD o VCR en el control remoto. Sin embargo, si usted presiona primero OUTPUT en el panel delantero, necesitará volver a seleccionar el modo correspondiente presionando DVD o VCR en el control remoto.
28.
Botón h
● Modo DVD
Presiónelo para ver la imagen de un DVD en retroceso rápido. Presione PAUSE y luego presione este botón para iniciar la reproducción a cámara lenta. Presione repetidamente este botón para cambiar la velocidad de retroceso de la reproducción a cámara lenta.
● Modo VCR
Presione para rebobinar la cinta o para ver la imagen rápidamente en inversión durante el modo de reproducción.(Búsqueda en Rebobinado).
29.
Botón Stop
● Modo DVD
Presiónelo para detener el disco.
●
Modo VCR
Presiónelo para detener la cinta.
30.
Botón RECORD
Presione para iniciar una grabación.
31.
Botón MENU
●
Modo DVD
Presione para visualizar el menú del Disco.
● Modo VCR
Presione para tener acceso al menú VCR.
32.
Botón TITLE
33.
Botón SETUP
Presiónelo para entrar en el modo de preparación del reproductor DVD.
34.
Botón ZOOM
Amplía parte de una imagen reproducida-DVD.
35.
Botón MODE
Activa modo de reproducción de programa o reproducción aleatoria cuando se reproducen CDs o
MP3. Ajusta Nivel de negro SONIDO VIRTUAL
SURROUND.
36.
Botón SUBTITLE
Presione para seleccionar un idioma de subtítulo deseado.
37.
Botón ANGLE
Presione para cambiar el ángulo de cámara para ver la secuencia que se está reproduciendo desde un ángulo diferente.
38.
Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
39.
Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
40.
Botón SEARCH MODE
●
Modo DVD
Presione para tener acceso o remover la indicación de búsqueda, que le permite ir directamente a un
Título/Capítulo/Pista/Tiempo especificado.
●
Modo VCR
Presione para avanzar o rebobinar rápidamente la cinta a una longitud específica de tiempo.
41.
Botón CLEAR/C.RESET
●
Modo DVD
Presione para reponer el ajuste.
● Modo VCR
Presione para reponer el contador. Presione para salir de la pantalla menu.
42.
Botón RETURN
● Modo DVD
Vuelve a la operación previa.
43.
Botones de flecha
Utilice cuando haga ajustes mientras mira la indicación en una pantalla de TV.
●
Modo VCR [página 16]
Botones p/o
Presiónelos para ingresar dígitos cuando establezca un programa (por ejemplo: puesta en hora del reloj o programación de temporizador). Presiónelos para seleccionar los modos de ajuste desde el menú de la pantalla.
Botón B
Cuando programa (por ejemplo: puesta en hora del reloj o programación de temporizador), presiónelo para determinar su selección y pasar al siguiente paso que desee introducir. Presiónelo para determinar los modos de ajuste desde el menú de la pantalla. Presiónelo para añadir o borrar números de canales durante el preajuste de canales.
Botón {
Presiónelo para cancelar un ajuste de programa de temporizador. Presiónelo para corregir dígitos cuando se programa (por ejemplo: puesta en hora del reloj o programación de temporizador). Presiónelo para añadir o borrar números de canales durante el preajuste de canales.
44.
Botón ENTER
Presione para aceptar un ajuste.
45.
Botón g
●
Modo DVD
Presione para avanzar rápidamente el Disco. Presione el Botón PAUSE, luego presione el Botón FWD iniciar a reproducción en movimiento lento. Presione el Botón FWD repetidamente para cambiar la velocidad de avance del movimiento lento.
– 36 – SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 37
● Modo VCR
Presione para avanzar rápidamente la cinta o ver la imagen rápidamente en avance durante reproducción.
(Búsqueda en Avance).
46.
Botón PLAY
● Modo DVD
Presiónelo para iniciar la reproducción.
●
Modo VCR
Presiónelo para iniciar la reproducción.
.47. Botón VCR
Presione antes de utilizar el control remoto para funciones de VCR.
● Usted puede cambiar el modo OUTPUT presionando
OUTPUT en el panel delantero o presionando DVD o VCR en el control remoto. Sin embargo, si usted presiona primero OUTPUT en el panel delantero, necesitará volver a seleccionar el modo correspondiente presionando DVD o VCR en el control remoto.
48.
Botón PAUSE
● Modo DVD
Presione para pausar la reproducción de Disco.
Presione repetidamente para avanzar la imagen DVD paso a paso (o un fotograma cada vez).
● Modo VCR
Mientras graba, presione para detener provisionalmente la grabación (pausa). Presione por segunda vez para reanudar la grabación normal.
Usted no puede pausar Grabación de Un-Toque. O, presione durante la reproducción de cinta para congelar la imagen.
53 54 55 56 57
49.
Botón SLOW
Durante la reproducción de cinta, presione mirar la cinta de videó a movimiento lento. Presione de nuevo para reanudar la reproducción normal. Este Botón no afecta la reproducción DVD.
50.
Botón VCR/TV
Utilice para seleccionar la posición VCR o TV.
●
Posición VCR
Para ver la reproducción, monitorear las grabaciones de vídeo o ver un programa de TV utilizando el sintonizador de la VCR.
●
Posición TV
Para ver un programa de TV o para ver un programa mientras se graba otro.
●
Posición de TV
Utilice para mirar TV (cambiando canales en el TV) o para mirar un programa mientras graba otro.
51.
Botones SKIP/CH
●
Modo DVD
Presione para saltar Capítulos o Pistas.
● Modo VCR
Presione para cambiar canales de TV en la
DVD/VCR.
52.
Botón AUDIO
Presione para seleccionar un idioma de audio deseado o modo de sonido.
VISIÓN TRASERA
ANT-IN
DVD/VCR VCR
AUDIO OUT AUDIO IN
L L
ANT-OUT
R
VIDEO OUT VIDEO IN
R
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
Y
DIGITAL
AUDIO OUT
Cb
Cr
L
COAXIAL
R
66
65 61
53.
Toma ANTI-IN (Entrada de Antena)
Conecte su antena, caja de cable o caja de descodificador de satélite.
54.
Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas de entrada de audio de un televisor u otro equipo de audio.
55.
Tomas AUDIO IN
Conecte aquí los cables de audio procedentes de las tomas de salida de audio de un camcorder, otra VCR o una fuente de audio.
56.
Cordón de Alimentación AC
Conecte a una toma de corriente AC estándar para suministrar corriente al DVD/VCR.
Sólo DVD
57.
Tomas COMPONENT VIDEO OUT
Conecte aquí los cables de videó componente opcionales y a las tomas de entrada de Videó componente de un televisor.
58.
Toma COAXIAL
Conecte aquí un cable de audio digital coaxial opcional y a la toma de entrada de audio digital coaxial de un descodificador o receptor de audio.
60
59 58
59.
Tomas DVD ANALOG AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas de entrada de audio de un televisor u otro equipo de audio (sólo DVD).
60.
Toma S-VIDEO OUT
Conecte aquí un cable de S-Videó opcional y a la toma de entrada de S-Videó de un televisor. (sólo
DVD)
61.
Toma VIDEO IN
Conecte un cable procedente de la toma de salida de videó de un camcorder, otra VCR o una fuente de audio-visual (reproductor de disco láser, reproductor de disco de videó, etc.) aquí.
62.
Toma DVD/VCR VIDEO OUT
Conecte aquí el cable de videó amarillo (provisto) y a la toma de entrada de Videó de TV.
63.
Toma ANT-OUT (Salida de Antena)
Utilice el cable coaxial RF provisto para conectar esta toma a la Toma ANTENNA IN en su TV.
Caja de cable o Sistema de Radiodifusión Directa.
Notas
¡ La toma S-VIDEO OUT, toma COAXIAL, toma OPTICAL y tomas COMPONENT VIDEO OUT son sólo
útiles en el modo DVD.
– 37 – SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 38
CAMBIO DE VCR/DVD
Debido a que este producto es una combinación de videograbadora y reproductor de DVD, debe seleccionar primero el equipo que desea hacer funcionar con el botón OUTPUT.
MODO VCR
Presione el Botón VCR en el control remoto.
(Verifique que la Luz VCR OUTPUT está enendida.)
MODO DVD
Presione el Botón DVD en el control remoto.
(Verifique que la Luz DVD OUTPUT está encendida)
Notas
¡ Presionando sólo el Botón OUTPUT en el panel delantero no cambia el modo del control remote. Usted siempre necesita seleccionar el modo correcto en el control remote, también.
DVD
STOP PLAY
OPEN/CLOSE
DVD DVD
OUTPUT
VCR TIMER REC REC
VCR
REW F.FWD
VIDEO L AUDIO R
POWER
CHANNEL STOP/EJECT
PLAY
POWER SPEED AUDIO
1
4
2
5
7 8
DISPLAY
0
DVD
3
SKIP/CH.
6
VCR/TV
9
SLOW
+ 10
VCR PAUSE
DVD
OUTPUT
Botón DVD
Luz DVD OUTPUT
Botón VCR
VCR TIM
Luz VCR OUTPUT
Botón OUTPUT
PLAY
STOP
RECORD
MENU
SETUP TITLE
ENTER
RETURN
MODE ZOOM
SEARCH
MODE
CLEAR/
C.RESET
SUBTITLE ANGLE REPEAT A-B
T-SET
– 38 – SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 39
CONEXIONES
CONEXION A UN TV SIN TERMINALES A/V
1. Desconecte el cordón de alimentación AC del toma de corriente AC.
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT.IN del DVD/VCR.
4. Conecte el DVD/VCR al TV utilizando el cable coaxial RF.
5. Enchufe los cordones de alimentación CA del DVD/VCR y TV dentro de las tomas de corriente AC.
CANAL DE SALIDA RF para DVD/VCR
1. Conecte el DVD/VCR a un TV utilizando un cable RF (consulte CONEXION A UN TV SIN
TERMINALES A/V.)
2. Seleccione el canal 3 en su TV.
3. Presione PLAY.
● Si hay ruido cambie el canal de salida RF de la UNIDAD COMBINADA DVD/VCR al canal 4 presionando PLAY en la videograbadora durante 3 segundos durante la reproducción.
CONEXION A UN TV CON TERMINALES A/V
Por favor, vea la [Fig.1] en la página 13 para detalles.
CONECTANDO A UN TV QUE TIENE TOMA DE ENTRADA DE S-
VÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE
Por favor, vea la [Fig. 2] en la página 14 para detalles.
CONEXION A UN AMPLIFICADOR ESTERO EQUIPADO CON
TOMAS DE ENTRADA DIGITAL COMO UNA PLATINA DE MINIDIS-
COS O UNA PLATINA DE CINTAS AUDIODIGITALES
Por favor, vea la [Fig. 4] en la página 14 para detalles.
CONEXION A UN RECEPTOR CON DESCODIFICADOR DIGITAL DOLBY
Por favor, vea la [Fig. 5] en la página 15 para detalles.
CONEXION A UN SISTEMA DE AUDIO ANALOGICO
Por favor vea la [Fig. 6] en la página 15 para detalles.
PREPARACIÓN
PREPARACIÓN DE CANAL AUTOMÁTICA
1 Conecte el TV y ponga el TV en el canal 3 ó 4.
2 Conecte el DVD/VCR presionando POWER.
Ambas Luces POWER y VCR/TV se encenderán.
VCR
4
Inicie canal preajustado presionando B una vez. El sintonizador explora y memoriza todos los canales activos de su área.
5 Después de explorar, el sintonizador de detiene en el canal memorizado más bajo.
La pantalla de TV retorna al modo TV.
3 Seleccione el Idioma en la pantalla (“INGLÉS”,
“FRANCÉS” o “ESPAÑOL”) presionando K o L.
Luego, presione B.
– 39 – SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 40
PREPARACIÓN DE RELOJ
VCR
Ajuste el reloj con precisión para grabación con temporizador automática adecuada. Le sugerimos que usted utilice un TV o estación de radio como su fuente de tiempos.
1 Presione MENU dos veces para llamar el menú principal. (Si usted ha ajustado ya el reloj, usted sólo tiene que presionarlo una vez).
¡ Si el reloj no está ajustado, aparece primero el menú
CLOCK SET. En este caso, siga el paso [3].
2 Seleccione “CLOCK SET” presionando Ko L.
Luego, presione B
3 Ajuste el reloj.
¡ Para retroceder un paso, presione {
4 Ponga en marcha el reloj presionando
CLEAR/C.RESET o B .
1) Ajuste el mes
Presione o o p repetidamente
Luego, presione B.
2) Ajuste el día
Presione o o p repetidamente
Luego, presione B.
3) Ajuste el año
Presione o o p repetidamente
Luego, presione B.
El día de la semana aparecerá automáticamente.
4) Ajuste la hora
Presione o o p repetidamente
Luego, presione B.
REPRODUCCIÓN DE UN DISCO
REPRODUCIENDO UN DVD,
VIDEO O UN CD AUDIO
DVD CD
Para empezar
Conecte la alimentación del TV, amplificador y cualquier otro componente que se encuentre conectado al DVD/VCR. (Cambie el sistema de entrada para que se adapte DVD/VCR y compruebe que el volumen de sonido sea correcto).
1
Presione el Botón POWER.
¡ “Load” aparecerá brevemente en el panel de visualización.
Compruebe que la Luz DVD OUTPUT está encendida. Si no, presione el Botón DVD en el control remote para cambiar el modo DVD/VCR.
2 Presione el Botón OPEN/CLOSE.
¡ La bandeja de carga del disco se abrirá.
3 Ponga un disco en la bandeja.
¡ Asegúrese de que el disco está asentado correctamente, con el lado de la etiqueta arriba.
4 Presione el Botón PLAY.
¡ La bandeja se cerrará automáticamente, y la reproducción empezará luego desde el primer capítulo o pista del disco. Usted necesita presionar el Botón PLAY sólo cuando la bandeja se ha cerrado presionando el Botón OPEN/CLOSE.
5 Presione el Botón STOP para detener la reproducción.
5) Ajuste el minuto
Presione o o p repetidamente
Luego, presione B.
6) Ajuste el AM o PM
AJUSTE DE RELOJ
Presione o o prepetidamente.
MES DIA AÑO
03 / 17 LUN 2003
HORA MINUTO AM/PM
05 : 40 PM AM
PM
– 40 – SP
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 41
MEMO
– 41 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 42
MEMO
– 42 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 43
MEMO
– 43 – EN
1L25
H9400UD(EN)2î
≈.qx33 03.2.18 5:48 PM Page 44
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE
UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429 http://www.funai-corp.com
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China 0VMN03452
H9400UD
★★★★
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 ABOUT COPYRIGHT
- 4 SUPPLIED ACCESSORIES
- 4 SYMBOLS USED IN THIS MANUAL
- 7 PLAYABLE DISCS
- 7 DISC TYPES
- 11 DISPLAY
- 11 DISPLAYS DURING OPERATION
- 11 LOADING THE BATTERIES
- 13 CONNECTING TO A TV WITHOUT A/V TERMINALS
- 13 CONNECTING TO A TV WITH A/V TERMINALS
- 14 JACK OR COMPONENT VIDEO IN JACKS
- 14 DAT DECK
- 15 DOLBY DIGITAL DECODER
- 15 CONNECTING TO AN ANALOG AUDIO SYSTEM
- 16 AUTOMATIC CHANNEL SET UP
- 17 TO CHANGE THE ON-SCREEN LANGUAGE
- 17 CLOCK SET UP
- 18 NORMAL PLAYBACK
- 18 AUTO REPEAT PLAYBACK
- 18 SEARCH FUNCTIONS
- 19 NORMAL RECORDING
- 19 OTR (One Touch Recording)
- 19 TIMER RECORDING
- 20 HINTS FOR TIMER RECORDING
- 21 COPYING A VIDEO TAPE
- 21 MTS (Multi-Channel Television Sound) SYSTEM
- 22 AUTO REWIND
- 22 REAL TIME TAPE COUNTER
- 22 BASIC PLAYBACK
- 22 GENERAL FEATURES
- 22 PAUSE
- 23 DISC MENU
- 23 TITLE MENU
- 23 STEP BY STEP PLAYBACK
- 23 RESUME
- 23 FAST FORWARD / REVERSE SEARCH
- 23 SLOW FORWARD / SLOW REVERSE
- 24 TRACK
- 24 TITLE / CHAPTER SEARCH
- 24 TIME SEARCH
- 25 REPEAT
- 25 PROGRAM
- 26 RANDOM PLAYBACK
- 26 MP3 PLAYBACK
- 26 ON-SCREEN INFORMATION
- 26 TRACK SELECTION
- 27 RANDOM PLAYBACK
- 27 PROGRAM
- 27 AUDIO LANGUAGE
- 27 STEREO SOUND MODE
- 27 SUBTITLE LANGUAGE
- 27 CAMERA ANGLE
- 28 CHANGING THE ON-SCREEN DISPLAY
- 28 PARENTAL CONTROL
- 29 MARKER SETUP SCREEN
- 29 AUDIO SETTING
- 30 BLACK LEVEL SETTING
- 30 VIRTUAL SURROUND
- 30 DISPLAY SETTING
- 31 LANGUAGE SETTING
- 39 DVD/VCR A CONEXIÓN DE TV
- 39 CANAL DE SALIDA DE RF
- 39 CONECTANDO A UN TV
- 39 COMPONENTE
- 39 PLATINA DAT
- 39 CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY
- 39 CONECTANDO A UN AUDIO ANALÓGICO
- 39 PREPARACIÓN DE CANAL AUTOMÁTICA
- 40 PREPARACIÓN DE RELOJ
- 40 REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO