YAS529 Catalog
YAS529
MS-3C
Magnetic field Sensor
„ Overview
YAS529 is the Triaxial Geomagnetic Sensor IC integrating buffer amplifier, A/D converter, clock generator,
and serial data interface circuit (supports I2C bus) on one chip package.
YAS529 allows you to make up a high sensitive, compact and low-power electronic compass in a portable
GPS system or a mobile phone.
„ Features
● A manufacturing process that makes magnetic sensor on Si wafer with high precision realizes integration
with peripheral circuits on one chip.
● High sensitive geomagnetic sensor IC is realized by integrating magnetic sensors and low noise
amplifiers.
● High noise immunity is improved by digitizing output from geomagnetic sensor IC.
● External interface supports I2C bus (100kbps/400kbps, slave mode).
● Geomagnetic sensor with superior high board density and low-power consumption.
● Automatic power-down control mode is available after geomagnetic measurements.
● Three A/D input pins for an inclination sensor
● Power-down control of an inclination sensor with a standby pin by the use of the General-Purpose Output
(GPO) Pin
● Others.
Manufacturing process ......................... CMOS + Magnetic Sensor
Package ................................................ Lead-free 10-pin WLCSP package (YAS529-PZ)
Supply voltage for core ........................ 2.5 V to 3.6 V
Supply voltage for Interface ................. 1.65 V to VDD (Operating temperature : -20 to +95 °C)
2.30 V to VDD (Operating temperature : -40 to +95 °C)
Operating temperature .......................... -40 to +95 °C (Supply for the interface : 2.30V to VDD)
Consumption current during operation.
Magnetic field measurement ....... 4 mA (VDD = 3.0 V)
Magnetic sensor section
Measuring magnetic field range .. ±300 µT
Resolution .................................... ≦0.6 µT/count (X,Y), ≦1.2 µT/count (Z)
Measuring time
Magnetic sensor measurement .... within 10 ms (Three axes collective measurement)
Inclination sensor A/D ................ within 10 ms (Three axes collective measurement)
YAS529 CATALOG
CATALOG No.: LSI-BAS529A20
2007.6
YAS529
„ Pin Description
Here are figures for pin assignment and a table for pin descriptions.
9
1
8
7
10
5
2
3
10-pin WLCSP
6
6
7
8
5
10
3
2
4
4
Top View
10-pin WLCSP
9
1
Bottom View
Pin Descriptions
Pin No.
Pin Name
I/O
Function
1
GPO
O
General-purpose output pin
2
VSS
-
Ground
3
AIZ
A
A/D input 3
4
A
A
A/D input 1
5
AIX
AIY
6
VDD
-
Power supply for core (Typ. 3 V)
7
8
SDA
SCL
I/Od
I
9
IOVDD
-
Power supply for interface (Typ. 1.8V)
10
RSTN
Is
Device initialization
A/D input 2
Serial data
Serial clock
Note)
Connecting AIZ to VDD is recommended when used by connecting a biaxial inclination sensor.
When the inclination sensor is not used, connecting AIX, AIY, and AIZ to VSS is recommended.
No Schmitt circuit is used for SCL and SDA input pins.
A
I
Is
Od
O
2
: Analog input
: Digital input
: Schmitt input
: Open drain output
: Output
YAS529
„ Pin Functions
z Power Supply (VDD, IOVDD, VSS)
These pins are for power supply of YAS529.
VDD
IOVDD
VSS
: Power Supply for core
: Power Supply for the Interface
: Ground
z Serial Data Interface (SCL, SDA, RSTN, GPO)
SCL
SDA
RSTN
GPO
: Serial clock input pin
These pins are used with an external pull-up resistor.
: Serial data input/output pin
These pins are used with an external pull-up resistor.
: Serial data interface reset pin
“L” releases I2C bus.
When not used, connect to IOVDD pin.
: General-purpose output pin
z Analog Input
AIX, AIY, AIZ : A/D input pin
Connecting AIZ to VDD is recommended when used by connecting a biaxial
inclination sensor.
When the inclination sensor is not used, connecting AIX, AIY, and AIZ to VSS is
recommended.
3
YAS529
„ Block Diagram
Here is the internal block diagram of YAS529.
Block Diagram
4
YAS529
„ Function Descriptions
z Analog Circuit Section
○ Magnetic Sensor
YAS529 includes three Magnetic Sensors.
Only the sensor of an axis to measure at the time of magnetic field measurement is operated.
○ Buffer Amplifier
The buffer amplifier amplifies a signal output from the bridge of magnetic sensor.
The amplifier operates only when magnetic field measurement is made.
○ Temperature Sensor
This is the sensor to correct the temperature characteristics of the magnetic sensor.
The sensor operates only when temperature is measured.
○ A/D Converter (ADC)
The A/D converter converts input signals from magnetic sensor output amplified by the buffer
amplifier, temperature sensor output, and external input pin.
The converter operates only when a measurement is performed.
○ Clock Generator
The clock generator supplies clocks to ADC and digital circuits.
The generator operates only when a measurement is performed.
○ Power-on Reset
The Power-on Reset circuit detects a rising edge of the supply voltage for the core and
initializes the circuits.
○ Initialization Coil
The coils are used when the magnetic sensor cannot exert the original characteristics due to
receiving high magnetic field.
Generating magnetic field with the initialization coils initializes the magnetic sensor
characteristics.
○ Analog External Input A/D
The A/D measures values from analog external input.
Input range is from 0.5 to 2.5V. One count of A/D converter is about 3.0mV.
5
YAS529
z Digital Circuit Section
○ Serial Data Interface
YAS529 serial data interface supports I2C bus serial interface and operates in the slave mode.
SCL (SCL)
: Serial clock input pin
SDA (SDA)
: Serial data input/output pin
Communication is performed through the above pins.
○ General-Purpose Output (GPO) Pin
YAS529 has GPO as general-purpose output pin. This output pin can be used for
purposes such as power-down control of an inclination sensor with standby pin.
6
YAS529
„ Example of System Configuration
Here is an example of system configuration.
When RSTN pin is not used, connect it to IOVDD pin.
Example of system configuration
Example of system configuration (RSTN pin is not used)
7
YAS529
„ Package Outline Drawing
Caution
* The product of the WLCSP package should be used under light-shielded conditions.
Since the WLCSP package has a structure that a silicon wafer is exposed, if light (such as sunlight) hits the
wafer, the device may malfunction (leak current increase etc.) due to electric charge internally generated by the
photoelectric effect.
* Please mount the package without underfill because temperature correction may not be normally performed
when mounting YAS529 on a board.
8
YAS529
YAS529
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement