Fujitsu S7010 User's Manual

Add to my manuals
28 Pages

advertisement

Fujitsu S7010 User's Manual | Manualzz

Fujitsu LifeBook

S Series

BIOS Guide

LifeBook S Series Model:

S7010

Document Date: 3/22/04

Document Number: FPC58-1109-01

F U J I T S U C O M P U T E R S Y S T E M S

1

L i f e B o o k S S e r i e s N o t e b o o k B I O S

S Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there should be no need to set or change the

BIOS environment to operate your notebook.

The BIOS Setup Utility configures:

Device control feature parameters, such as changing

I/O addresses and boot devices.

System Data Security feature parameters, such as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1. Turn on or restart your notebook.

2. Press the [F2] key when a message appears under the

Fujitsu logo prompting you to “Press <F2>: BIOS

Setup”. This will open the main menu of the BIOS

Setup Utility with the current settings displayed.

3. Press the arrow keys to scroll through the other setup menus to review or alter the current settings.

Navigating Through the Setup Utility

The BIOS setup utility consists of six menus: Main,

Advanced, Security, Boot, Info and Exit. This document explains each menu in turn including all submenus and setup items.

The following procedures allow you to navigate the setup utility menus:

1. To select a menu, use the cursor keys:

[ ], [ ].

2. To select a field within a menu or a submenu, use the cursor keys: [ ], [ ].

3. To select the different values for each field, press the

[Spacebar] to change to the next higher selection and [F5] or [-] to go to the next lower selection.

4. To activate a submenu press the [Enter] key.

5. To return to a menu from a submenu, press the

[Esc] key.

6. To go to the Exit menu from any other menu, press the [Esc] key.

■ Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen.

■ Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed.

Pressing the Enter key again will select the highlighted choice.

7. Pressing the [F9] key resets all items in the BIOS to the default values.

8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed.

9. Pressing the [F1] key gives you a general help screen.

Entering the Setup Utility After a Configuration

Change or System Failure

If there has been a change in the system configuration that does not agree with the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too severe, it will give you the opportunity to modify the settings of the setup utility, as described in the following steps:

1. When you turn on or restart the computer there is a beep and/or the following message appears on the screen:

Error message - please run SETUP program Press <F1> key to continue,

<F2> to run SETUP

2. If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key.

■ If your notebook emits a series of beeps that sounds like a code and the display is blank, refer to the Troubleshooting section of your system Use’s Guide. The

Troubleshooting Section includes a list of error messages and their meanings.

■ If your data security settings require it, you may be asked for a password before the operating system will be opened.

2

3. If an error message is displayed on the screen, and you want to enter the setup utility, press the [F2] key.

4. When the setup utility starts with a fault present, the system displays the following message:

Warning!

Error message

[Continue]

5. Press any key to enter the setup utility. The system will then display the Main Menu with current parameters values.

M a i n M e n u

3

L i f e B o o k S S e r i e s N o t e b o o k B I O S

MAIN MENU – SETTING STANDARD SYSTEM PARAMETERS

The Main Menu allows you to set or view the current system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes.

(See Navigating Through the Setup Utility on page 2 for more information)

The following tables show the names of the menu fields for the Main menu and its submenus, all of the options for each field, the default settings and a description of the field’s function and any special information needed to help understand the field’s use. Note that the actual drive labels shown may vary .

System Time and System Date can also be set from your operating system without using the setup utility. Use the calendar and time icon on your Windows Control panel or type time or date from the MS-

DOS prompt.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Info Exit

Item Specific Help

System Time:

System Date:

[ 02 :34:56]

[03/17/2004]

Primary Master [TOSHIBA MK4025GAS-(PM)]

Secondary Master [None)]

Adjust calendar clock.

<Tab>, <Shift-Tab>, or

<Enter> selects field.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space Change Values

Enter Select Sub-Menu

Figure 1. Main Menu

Table 1: Fields, Options and Defaults for the Main Menu

Menu Field

System Time:

Options

–—

Default

–—

System Date: –— –—

F9 Setup Defaults

F10 Save and Exit

Description

Sets and displays the current time. Time is in a 24 hour format of hours:minutes:seconds with 2 digits for each. (HH:MM:SS).

Example: 16:45:57. You may change each segment of the time separately. Move between the segments with the [Tab] key and/or

[Shift] + [Tab] keys.

4

Sets and displays the current date. Date is in a month/day/year numeric format with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for example: 03/20/1998. You may change each segment of the date separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys.

M a i n M e n u

Table 1: Fields, Options and Defaults for the Main Menu

Menu Field

Primary

Master:

Options

Selects Primary

Master submenu

Default

The product # of the Hard Drive

Secondary

Master:

Language:

Selects Secondary

Master submenu

English (US)

Japanese (JP)

[None]

[English (US)]

Description

Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Primary Master submenu allowing additional device configuration options for this interface.

Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Secondary Master submenu allowing additional device configuration options for this interface.

The default setting differs between the US/European and the

Japanese model. Selects the display language for the BIOS.

5

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Primary Master Submenu of the Main Menu

The Primary Master submenu identifies what ATA devices are installed.

Note that actual hard drive label shown may vary.

Depending on the drive type, information such as cylinders, heads and sectors may also be displayed.

PhoenixBIOS Setup Utility

Main

Primary Master [TOSHIBA MK4025GAS-(PM)] Item Specific Help

Type: [ Auto ]

LBA Format

Total Sectors:

Maximum Capacity:

78140160

40008MB

Multi-Sector Transfers: [16 Sectors]

LBA Mode Control: [Enabled]

Transfer Mode:

Ultra DMA Mode:

[Multiword DMA 2]

[Disabled]

Select ATA/ATAPI drive installed here.

[Auto]

The BIOS auto-types the drive on boot time.

Except [Auto]

You enter parameters of the drive.

[None]

The drive is disabled.

Menu Field

Type:

LBA Format

Total Sectors:

Maximum

Capacity:

CHS Format

Cylinders:

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup

F10 Save and Exit

Options

Auto

None

CD-ROM

Hard Disk

---

---

Figure 2. Primary Master Submenu

Default

[Auto]

---

---

■ A number between

0 and 65,535

–—

Description

Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM if a

CD-ROM drive is installed at this connection. If Hard Disk is selected, you must specify the number of Cylinders, Heads, and Sectors for the drive.

Logical Block Addressing (LBA)

The total number of sectors on your hard disk

The maximum capacity of your hard disk

Cylinders/Heads/Sectors

This item is active only when Hard Disk is selected as the type. This field is changed by incrementing (pressing the [Spacebar]) or by typing in the number.

6

M a i n M e n u

Menu Field

Heads:

Sectors:

Maximum

Capacity:

Options

■ A number between

1 and 16

Default

–—

■ A number between

0 and 63

–—

■ Display only –—

Multi-Sector

Transfers:

LBA Mode Control:

Disabled

2 Sectors

4 Sectors

8 Sectors

16 Sectors

Disabled

Enabled

[16 Sectors]

[Enabled]

Transfer Mode:

Ultra DMA Mode:

Standard

Fast PIO 1

Fast PIO 2

Fast PIO 3

Fast PIO 4

Multiword DMA 1

Multiword DMA 2

Disabled

Mode 0

Mode 1

Mode 2

Mode 3

Mode 4

Mode 5

[Multiword

DMA 2]

[Disabled]

Description

This item is active only when Hard Disk is selected as type. You can change the value by incrementing (pressing the [Spacebar]) or by typing in the number.

This item is active only when Hard Disk is selected as type. You can change the value by incrementing (pressing the [Spacebar]) or by typing in the number.

Displays the maximum capacity of the drive calculated from the parameters of the hard disk when Auto is selected and the type is identified as hard disk.

This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer.

Enables or disables logical Block Addressing in place of Cylinder,

Head, Sector addressing. This option cannot be changed when Auto is selected.

Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.

Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.

■ A bootable CD-ROM may have either a floppy disk or hard drive format. When the bootable CD-ROM is used, the drive allocations change automatically without changing the BIOS setup. If a floppy disk format

CD-ROM is used, the CD-ROM becomes Drive A. The CD-ROM will only take drive C: (hard drive format) if the internal hard drive is not present or is disabled. The bootable CD-ROM can never use a C: designation if a formatted internal hard drive is present since the C: designator is always reserved for the internal hard drive.The boot sequence ignores the new drive designations, however, your application software will use the new designations.

■ Be aware of the operating environment when booting from a CD-ROM or you may overwrite files by mistake.

7

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Secondary Master Submenu of the Main Menu

The Secondary Master submenu is for the internal CD-

ROM drive. The drive type is displayed on this menu as well as the Main menu. Your notebook auto-senses the characteristics of the internal drive installed. You will not need to modify these settings; they are displayed for your reference.

Note that actual drive labels shown may vary.

PhoenixBIOS Setup Utility

Main

Secondary Master [TOSHIBA DVD-ROM SD-R2412-(SM)] Item Specific Help

Type: [ Auto ]

Multi-Sector Transfers: [Disabled]

LBA Mode Control: [Disabled]

Transfer Mode:

Ultra DMA Mode:

[Standard]

[Disabled]

Select ATA/ATAPI drive installed here.

[Auto]

The BIOS auto-types the drive on boot time.

Except [Auto]

You enter parameters of the drive.

[None]

The drive is disabled.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 3. Secondary Master Submenu

Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu

Menu Field

Type:

Multi-Sector

Transfers:

LBA Mode

Control:

Options

Auto

None

CD-ROM

Hard Disk

Disabled

2 Sectors

4 Sectors

8 Sectors

16 Sectors

Disabled

Enabled

Default

[Auto]

[Disabled]

[Disabled]

Description

Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM or Hard Disk for appropriate drive type installed at this connection.

This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer.

Enables or disables Logical Block Addressing in place of Cylinder, Head,

Sector addressing. This option cannot be changed when Auto is selected.

8

M a i n M e n u

Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu

Menu Field Options

Transfer Mode: ■

Standard

Fast PIO 1

Fast PIO 2

Fast PIO 3

Fast PIO 4

Multiword DMA 1

Multiword DMA 2

Ultra DMA

Mode:

Disabled

Mode 0

Mode 1

Mode 2

Mode 3

Mode 4

Mode 5

Default

[Standard]

[Disabled]

Description

Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.

Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected.

Exiting from Main Menu

When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit menu or to move to another menu.

9

L i f e B o o k S S e r i e s N o t e b o o k B I O S

ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS

The Advanced Menu allows you to:

Set the I/O addresses for the serial and parallel ports.

Set the features of the keyboard/mouse.

Select between the display panel and/or an external

CRT display.

Set internal device configurations

Configure USB and CPU features.

Configure miscellaneous features such as Wake Up On

LAN.

Configure DMI Event Logging.

Follow the instructions for Navigating Through the

Setup Utility to make any changes.

(See Navigating Through the Setup Utility on page 2 for more information)

The following tables show the names of the menu fields for the Advanced Menu and its submenus, all of the options for each field, the default settings and a description of the field’s function, and any special information needed to help understand the field’s use.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Info Exit

Serial/Parallel Port Configurations

Keyboard/Mouse Features

Video Features

Internal Device Configurations

CPU Features

USB Features

Miscellaneous Configurations

Event Logging

Item Specific Help

Configures serial ports and parallel ports

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

Figure 4. Advanced Menu

F9 Setup Defaults

F10 Save and Exit

10

A d v a n c e d M e n u

Table 4: Fields, Options and Defaults for the Advanced Menu

Menu Field

Serial/Parallel Port

Configurations

Keyboard/Mouse

Features

Video Features

Internal Device

Configurations

CPU Features

USB Features

Miscellaneous

Configurations

Event Logging

Description

When selected, opens the Serial/Parallel Port Configurations submenu which allows the user to modify settings for serial, infrared and parallel ports.

When selected, opens the Keyboard/Mouse Features submenu, which allows setting external and internal keyboard and mouse parameters.

When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays.

When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the modem, IDE, and LAN Controllers.

When selected, opens the CPU Features submenu, which allows you to change the Intel(R) SpeedStep(R)

Technology settings.

Configures USB features.

Configures miscellaneous features, such as Wake Up On LAN and Power Button.

When selected, opens the event logging submenu.

11

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Serial/Parallel Port Configuration Submenu of the Advanced Menu

The Serial/Parallel Port Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the serial, infrared, and parallel ports of your notebook.

■ To prevent IRQ and address conflicts, avoid changing the default settings. If you must change the settings, you can call 1-800-8Fujitsu for technical assistance.

The BIOS will warn you of resource conflicts by placing a yellow asterisk next to each device that is in conflict.

■ All I/O addresses in Table 5 are in hexadecimal.

I/O addresses, DMA channels, and

Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices, serial or parallel, have the same I/O address assigned your notebook will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc.

Advanced

PhoenixBIOS Setup Utility

Serial/Parallel Port Configurations

Serial Port:

I/O Address:

Interrupt:

Infrared Port:

Mode:

I/O Address:

Interrupt:

I/O Address:

DMA Channel:

Parallel Port:

Mode:

I/O Address:

Interrupt:

[ Enabled ]

[3F8-3FF]

[IRQ 4]

[Enabled]

[FIR]

[2E8 - 2EF]

[IRQ 3]

[400-43F]

[DMA 3]

[Enabled]

[Bi-directional]

[378-37F]

[IRQ 7]

Item Specific Help

[Disabled]

The port is disabled.

[Enabled]

The port is enabled with user configuration.

[Auto]

Plug & Play OS configure the port.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup

F10 Save and Exit

Figure 5. Serial/Parallel Port Configuration Submenu

12

A d v a n c e d M e n u

Table 5: Fields, Options and Defaults for Serial/Parallel Port Configuration Submenu of Advanced Menu

Menu Field

Serial Port:

I/O Address:

Interrupt:

Infrared Port:

Mode:

I/O Address:

Options

Disabled

Enabled

Auto

3F8 - 3FF

2F8 - 2FF

3E8 - 3EF

2E8 - 2EF

IRQ 3

IRQ 4

IRQ 10

IRQ 11

Disabled

Enabled

Auto

IrDA

FIR

Default

[Enabled]

[3F8 - 3FF]

[IRQ 4]

[Enabled]

[FIR]

[2E8 - 2EF]

Description

Configures the serial port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).

Allows user to set the serial port base I/O address when serial port is

Enabled.

Allows user to set the serial port interrupt when serial port is Enabled.

Configures the infrared port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).

When the infrared port is enabled this option is available allowing the user to set the mode for the infrared port. Standard IrDA (IrDA 1.0) transmits data at up to 115.2 Kbps; FIR (IrDA 1.1) transmits at up to 4Mbps.

Allows user to set the infrared port I/O address when the infrared port is

Enabled.

Interrupt:

I/O Address:

DMA Channel:

Parallel Port:

Mode:

I/O Address:

Interrupt:

3F8 - 3FF

2F8 - 2FF

3E8 - 3EF

2E8 - 2EF

IRQ 3

IRQ 4

IRQ 10

IRQ 11

400-43F

480-4BF

500-53F

580-5BF

DMA 1

DMA 3

Disabled

Enabled

Auto

Output Only

Bi-directional

ECP

378 - 37F

278 - 27F

3BC - 3BF

IRQ 5

IRQ 7

[IRQ 3]

400-43F

[DMA 3]

[Enabled]

[Bi-directional]

[378 - 37F]

[IRQ 7]

Allows user to set the infrared port interrupt when the infrared port is

Enabled.

Allows user to set the FIR port I/O address when the infrared port is

Enabled.

Allows user to set the infrared port DMA Channel when the infrared port mode is set to FIR.

Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto).

When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bi-directional allows two-way transfer of information between your notebook and a parallel device.

Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP

Mode allows communication with the ECP class of parallel I/O devices.

Allows user to set the parallel port base I/O address when the parallel port is Enabled.

Allows user to set the parallel port interrupt when the parallel port is

Enabled.

13

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Keyboard/Mouse Features Submenu of the Advanced Menu

The Keyboard/Mouse Features submenu is for setting the parameters of the integrated and external mouse and keyboard.

PhoenixBIOS Setup Utility

Advanced Security Power Savings Exit

Keyboard/Mouse Features Item Specific Help

Numlock:

Hot Plug:

Internal Pointing Device:

Initialization on Resume:

[ Auto ]

[Enabled]

[Auto Disabled]

[Fast]

Selects power-on state for Numlock.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 6. Keyboard/Mouse Features Submenu

Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu

Menu Field

Numlock:

Hot Plug:

Internal Pointing

Device:

Initialization on

Resume:

Options

Auto

On

Off

On/Padlock Off

Disabled

Enabled

Auto Disabled

Manual Setting

Always Enabled

Always Disabled

Fast

Normal

Default

[Auto]

[Enabled]

[Auto Disabled]

[Fast]

Description

Sets the NumLock function state when the computer completes booting.

Enables and disables the ability to plug a mouse or keyboard into the PS/2 port and have it immediately recognized and active.

Sets the device controlling the mouse cursor on the screen.

Always Enabled makes the pointing device always enabled whether there is an external mouse or not. Always Disabled makes the pointing device always disabled. Auto Disabled disables the internal pointing device when an external pointing device is connected to the PS/2 port.

When Fast is selected, initialization for the external devices is optimized to speed up on Resume. When Normal is selected, initialization is not optimized.

14

A d v a n c e d M e n u

Video Features Submenu of the Advanced Menu

The Video Features Submenu is for setting the display parameters.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Video Features Item Specific Help

Display: [Auto]

Compensation: [Enabled]

Select display terminal.

* This setting is not effective after operating system starts up.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 7. Video Features Submenu

Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu

Menu Field

Display:

Compensation:

Options

Internal Flat Panel

External (Analog)

External (Digital)

Auto

Disabled

Enabled

Default

[Auto]

[Enabled]

Description

Selects where the video signal will be routed.

Enables or disables display compensation.

15

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Internal Device Configurations Submenu of the Advanced Menu

The Internal Device Configuration submenu allows the user to configure other internal devices.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Internal Device Configurations

IDE Contoller:

Modem Controller:

LAN Controller:

Wireless LAN:

[ Both

[Enabled]

[Enabled]

[Enabled]

Item Specific Help

[Disabled]

No IDE ports are enabled.

[Primary]

Only primary IDE port is enabled.

[Secondary]

Only secondary IDE port is enabled.

[Both]

Both primary and secondary IDE ports are enabled.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 8. Internal Device Configuration Submenu

Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu

Menu Field

IDE Controller:

Modem Controller:

LAN Controller:

Wireless LAN:

Options

Disabled

Primary

Secondary

Both

Disabled

Enabled

Disabled

Enabled

Auto

Disabled

Enabled

Default

[Both]

[Enabled]

[Enabled]

[Enabled]

Description

Enables or disables selected IDE devices.

Enables or disables the modem device.

Enables or disables the LAN controller.When Auto is selected, the

LAN will be disabled when the system is running on battery power and the LAN cable is not connected.

Enables or disables the Wireless LAN device.

16

A d v a n c e d M e n u

CPU Features Submenu of the Advanced Menu

The CPU Features Submenu allows you to change the settings for Intel(R) SpeedStep(R) Technology for your system.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

CPU Features Item Specific Help

SpeedStep(R) Technology:

[Enabled]

On Battery: [Battery Optimized]

On AC: [Maximum Performance]

Select Enhanced

Intel(R) SpeedStep(R)

Technology enabled or disabled.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup

F10 Save and Exit

Figure 9. USB Features Submenu

Table 9: Fields, Options and Defaults for the ACPI Features Submenu of the Advanced Menu

Menu Field

SpeedStep(R)

Technology:

Options

Disabled

Enabled

Default

[Enabled]

Description

Enables or disables SpeedStep(R) Technology which allows the user to determine the CPU performance when the tablet is running on AC or battery. This technology decreases power consumption by decreasing CPU speeds.

On Battery:

On AC:

Maximum Performance

Battery Optimized

Automatic

Maximum Performance

Battery Optimized

Automatic

■ Battery Optimized

■ Maximum Performance

Allows the user to select the CPU performance when the system is running on battery power.

Allows the user to select the CPU performance when the system is running on AC power.

17

L i f e B o o k S S e r i e s N o t e b o o k B I O S

USB Features Submenu of the Advanced Menu

The USB Features Submenu enables and disables legacy USB support for your system.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

USB Features Item Specific Help

Legacy USB Support: [Enabled]

SCSI SubClass Support: [Enabled]

[Disabled]

The feature is disabled.

[Enabled]

Legacy USB Emulation is enabled and USB devices are available without USB aware OS.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup

F10 Save and Exit

Figure 10. USB Features Submenu

Table 10: Fields, Options and Defaults for the ACPI Features Submenu of the Advanced Menu

Menu Field

Legacy USB

Support:

SCSI SubClass

Support:

Options

Disabled

Enabled

Disabled

Enabled

Default

[Enabled]

[Enabled]

Description

When Disabled is selected, legacy USB emulation is disabled. When

Enabled is selected, legacy USB emulation is enabled and USB devices are available without USB-aware OS.

When Enabled is selected, USB devices that belong to the SCSI subclass in the mass storage class (e.g., USB Memory Key) are enabled.

18

A d v a n c e d M e n u

Miscellaneous Configurations Submenu of the Advanced Menu

The Miscellaneous Configurations Submenu configures the miscellaneous features for your system.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Miscellaneous Configurations Item Specific Help

Power Button:

Wake up on LAN:

Volume Setting:

[ Disabled ]

[Disabled]

[Middle]

Configures the power button.

*ACPI OS ignores this setting.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 11. Miscellaneous Configurations Submenu

Table 11: Fields, Options and Defaults for the Miscellaneous Configurations Submenu

Menu Field

Power Button:

Wake up on LAN:

Volume Setting:

Options

Disabled

Power Off

Disabled

Enabled

Off

Minimum

Middle

Maximum

Default

[DIsabled]

[Disabled]

[Middle]

Description

When Disabled is selected, the power button does not respond to a press. When Power Off is selected, the button turns the power off.

When Enabled is selected, the system will wake up when the internal

LAN device receives a Magic Packet while the system is powered off.

Allows you to set or disable the system volume level.

19

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Event Logging Submenu of the Advanced Menu

The Event Logging Submenu configures event logging features for DMI events.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Event Logging Item Specific Help

Event Log Capacity: Space Available

Event Log Validity: Valid

View Event Log: [Enter]

Event Logging: [Enabled]

System Boot Event: [Disabled]

Clear All Event Logs: [No]

Mark Events as Read: [Enter]

Press <Enter> key to view the contents of the event log.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

Figure 12. Event Logging Submenu

F9 Setup Defaults

F10 Save and Exit

Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu

Options Default

Space Available

Description

Display only.

Menu Field

Event Log

Capacity:

Event Log Validity:

View Event Log:

Event Logging:

Valid

[Enter]

[Enabled]

Display only.

Allows you to view content of event log.

Turns event logging on and off for all DMI events.

System Boot

Event:

Clear All Event

Logs:

Mark Events as

Read:

■ Enter

Disabled

Enabled

Disabled

Enabled

No

Yes

■ Enter

[Disabled]

[No]

[Enter]

Turns event logging on and off for DMI system boot events.

When set to [Yes] all event logs will be cleared at next boot.

Allows you to make all events currently in the event log as read.

20

S e c u r i t y M e n u

SECURITY MENU – SETTING THE SECURITY FEATURES

The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to

make any changes. (See Navigating Through the Setup

Utility on page 2 for more information)

field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection .

The following tables show the names of the menu fields for the Security menu and its submenus, the options for each field, the default settings and a description of the

Entering a password incorrectly three times in a row will cause the keyboard and mouse to be locked out and the warning

[System Disabled] to be displayed. If this happens, restart the computer by turning off and on the power with the power switch and use the correct password on reboot.

■ If you set a password, write it down and keep it in a safe place. If you forget the password you will have to contact your support representative to regain access to your secured functions and data.

■ If you make an error when re-entering the password a [Warning] will be displayed on the screen. To try again press the [Enter] key and then retype the password. Press the [Esc] key to abort the password setting process.

■ If the Password on Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save-to-Disk modes.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Info Exit

Supervisor Password Is:

User Password Is:

Set Supervisor Password

Set User Password

Minimum User Password Length: [0]

Password on Boot: [Disabled]

On Automatic Wake up:

KB Lock on Resume:

Boot from Removable Media:

Flash Write:

Hard Disk Security

Owner Information

Security Panel On Resume:

Clear

Clear

[ Enter ]

[Enter]

[Disabled]

[Disabled]

[All]

[Enabled]

[Enabled]

Item Specific Help

Press <Enter> key to set Supervisor Password to enable any password features.

Then password entry is required to enter BIOS

Setup.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

Figure 13. Security Menu

F9 Setup Defaults

F10 Save and Exit

21

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Table 13: Fields, Options and Defaults for the Security Menu

Menu Field

Supervisor

Password is:

User Password is:

Set Supervisor

Password

Set User Password

Options

–—

–—

[Enter]

[Enter]

[0]

Default

Clear

Clear

[Enter]

[Enter]

[0]

Description

A display-only field. Set is displayed when the system Supervisor

Password is set and Clear when it is not.

A display-only field. Set is displayed when the general User Password is set, and Clear when it is not.

Sets, changes or cancels Supervisor Password. The Supervisor Password may be up to seven characters long and include only letters or numbers

(no symbols). Passwords are NOT case- sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor

Password is set it must be used to access the BIOS setup utility.

This field can only be accessed if the Supervisor Password is set. Sets, changes or cancels the User Password. The User Password may be up to seven characters long and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS setup utility.

Sets the minimum length for User Password.

Minimum User

Password Length:

Password on Boot: [Disabled]

On Automatic

Wake up:

KB Lock on

Resume:

Boot from

Removable Media:

Disabled

First Boot

Every Boot

Disabled

Enabled

Disabled

Enabled

[Disabled]

[Disabled]

[All]

When Enabled, a password (User or Supervisor) is required after the

Power On Self Test (POST) before the operating system will be read from a disk. When set to Disabled no password is required. If no Supervisor

Password is set this feature is not available and no password is required.

This field is active only when Password On Boot is set to First Boot or

Every Boot. When disabled, password entry is not required on automatic wake up on LAN or Real Time Clock. When enabled, the password is still required on automatic wake up.

When set to Enabled, the PS/2 keyboard and mouse inputs are locked out upon Suspend from Resume or Save-to-Disk mode until the password is entered. When both passwords are set, the User password is always used to lock. Password entry before OS boot is disabled upon unattended boot.

Enable password allows supervisor access only.

Flash Write:

Hard Disk Security:

All

Supervisor only

Disabled

Enabled

–—

[Enabled]

–—

When disabled, the BIOS Flash memory is write protected.

Owner

Information:

Security Panel On

Resume

–—

Disabled

Enabled

–—

[Enabled]

When selected, opens the Hard Disk Security submenu, which allows you to configure hard disk security features.

When selected, opens the Owner Information submenu, which allows you to set Owner information.

Allows the Security Panel Feature to be enabled or disabled upon

Suspend from Resume.

22

S e c u r i t y M e n u

Hard Disk Security Submenu of the Security Menu

The Hard Disk Security Submenu is for configuring hard disk security features.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Hard Disk Security Item Specific Help

Primary Master Password Is:

Secondary Master Password Is:

Set Primary Master Password

Set Secondary Master Password

Clear

Not Available

[Enabled]

[Enter]

Password Entry on Boot: [Enabled]

Press <Enter> key to set Hard Disk Password.

The hard disk is locked with the password. Data in the locked disk can not be read on other systems.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 14. Hard Disk Security Submenu

Table 14: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu

Menu Field

Primary Master

Password Is::

Secondary Master

Password Is:

Set Primary

Master Password

Options

---

---

---

Default

---

---

[Enter]

[Enter]

Description

A display-only field. Set is displayed when the Master Password is set and Clear when it is not.

A display-only field. Not Available is displayed.

Sets, changes or cancels Primary Master Password. The Primary Master Password may be up to seven characters long and include only letters or numbers (no symbols). Passwords are NOT case- sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter

New Password field. When a Primary Master Password is set it must be used to access the hard disk. Data on the hard disk cannot be read on other systems.

Not currently available.

Set Secondary

Master Password

Password Entry on

Boot:

---

Disabled

Enabled

[Enabled] When this is disabled, it is not necessary to enter the Hard Disk Password before booting.The hard disk is still password-protected without entering a password.

23

L i f e B o o k S S e r i e s N o t e b o o k B I O S

Owner Information Submenu of the Security Menu

The Owner Information Submenu is for setting owner information. Note that Owner Information cannot be set without having entered a supervisor’s password.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Exit

Owner Information Item Specific Help

Owner Information Is: Clear

Set Owner Information [Enter]

Foreground Color:

Background Color:

[Gray]

[Black]

Press <Enter> key to set owner information.

Up to 80 characters can be set. Available characters are ASCII codes from 32 through

126.

The owner information is always displayed at the bottom line of the screen during POST.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

Figure 15. Owner Information Submenu

F9 Setup Defaults

F10 Save and Exit

Table 15: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu

Menu Field

Owner

Information Is:

Set Owner

Information:

Foreground

Color:

Options

–—

–—

Default

Clear

[Enter]

[Gray]

Description

Display only.

Field to write owner information, e.g., your name.

Set foreground color.

Background

Color:

Black

Blue

Green

Cyan

Black

Blue

Green

Cyan

Red

Magenta

Brown

White

Red

Magenta

Brown

White

Gray

Light Blue

Light Green

Light Cyan

Gray

Light Blue

Light Green

Light Cyan

Light Red

Light Magenta

Yellow

Bright White

Light Red

Light Magenta

Yellow

Bright White

[Black] Sets background color.

Exiting from the Security Menu

When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to another menu. If you wish to exit from setup utility, press the [Esc] key to go to the Exit Menu. If you wish to move to another menu, use the cursor keys.

24

B o o t M e n u

BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE

The Boot Menu is used to select the order in which the

BIOS searches sources for the operating system. Follow the instructions for Navigating Through the Setup

Utility to make any changes. (See Navigating Through the

Setup Utility on page 2 for more information)

The following tables show the names of the menu fields for the Boot menu and its submenu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Info Exit

Item Specific Help

Quick Boot:

Boot Time Diagnostic Screen:

Boot Menu: [Enabled]

Preboot Execution Environment: [Disabled]

Boot Device Priority

[Enabled]

[Disabled]

[Disabled]

All diagnostic tests will be done.

[Enabled]

Some diagnostic tests may be skipped while booting to speed up.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 16. Boot Menu

Table 16: Fields, Options and Defaults for the Boot Menu

Menu Field

Quick Boot:

Boot Time

Diagnostic Screen:

Boot Menu:

Preboot Execution

Environment:

Boot Device

Priority:

Options

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Selects the Boot Device

Priority submenu

Default

[Enabled]

[Disabled]

[Enabled]

[Disabled]

__

Description

Turns on and off booting with a truncated set of Power On Self

Tests. (Fewer tests mean faster turn on.)

Turns on and off display of test results instead of Fujitsu logo screen during Power On Self Test.

When disabled, the boot menu is disabled and the F12 key is ignored. When enabled, the boot menu is enabled.

Turns on and off boot from network server options.

This menu allows setting up the source for the operating system.

See “Boot Device Priority Submenu” in the following section.

25

L i f e B o o k S S e r i e s N o t e b o o k B I O S

The Boot Device Priority Submenu of the Boot Menu

The Boot Device Priority Submenu is for setting the order of checking of sources for the operating system.

Be aware of the operating environment when booting from a CD-ROM or you may overwrite files by mistake.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Boot

Boot Device Priority Item Specific Help

+Floppy Disk Drive

+Hard Disk Drive

CD-ROM Drive

Keys used to view or configure devices:

<Enter> expands or collapses devices with a + or -.

<Ctrl+Enter> expands all.

<Shift+1> enables or disables a device.

<+>/<Space> or <-> moves the device up or down.

<d> removes a device that is not installed.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space

Enter

Change Values

Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 17. Boot Device Priority Submenu

Table 17: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu

Menu Field

+Floppy Disk Drive

+Hard Disk Drive

CD-ROM Drive

Description

The boot selections determine the order in which the BIOS searches for the operating system during a startup sequence. To change the order highlight one source by using the [up] or [down] cursor keys and then press the

[+] or [-] key to change the order number for that source. Be sure to save your changed order when you exit the

BIOS setup utility.

Exiting from Boot Menu

When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or move to another menu. If you wish to exit from the setup utility press the [Esc] key to go to the Exit menu. If you wish to move to another menu, use the cursor keys.

26

E x i t M e n u

INFO MENU – DISPLAYS BASIC SYSTEM INFORMATION

The Info menu is a display only screens that provides the configuration information for your notebook.

The following table shows the names of the menu fields for the Info menu and the information displayed in those fields. These fields are for information purposes only, and are not editable

.

The information, including CPU type and speed, and total memory, displayed on this screen varies according to the unit you purchased.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Info Exit

Item Specific Help

BIOS Version: 1.03

BIOS Date: 02/23/2003

BIOS Area: E000h - FFFFh

CPU Type:

CPU Speed:

L1 Cache:

L2 Cache:

Intel(R) Pentium(R) M

1.7 GHz

64 KB

1024 KB

Total Memory: 512 MB

Memory Slot 1: None

Memory Slot 2: 512 MB DDR SDRAM

F1 Help

ESC Exit

Select Item

Select Menu

-/Space Change Values

Enter Select Sub-Menu

Figure 18. Info Menu

F9 Setup

F10 Save and Exit

Table 18: Fields, Options and Defaults for the Info Menu

Note that the parameters listed in the following table may be different, depending upon your system configuration.

Menu Field

BIOS Version:

BIOS Date:

BIOS Area:

CPU Type:

CPU Speed:

Default

1.03

02/23/2004

E000h – FFFFh

Intel(R) Pentium(R) M

1.70 HGz

Menu Field

L1 Cache::

L2 Cache:

Total Memory:

Memory Slot 1:

Memory Slot 2:

Default

64 KB

1024 KB

512 MB

None

512 MB DDR SDRAM

27

L i f e B o o k S S e r i e s N o t e b o o k B I O S

EXIT MENU – LEAVING THE SETUP UTILITY

The Exit Menu is used to leave the setup utility. Follow the instructions for Navigating Through the Setup Utility to

make any changes. (See Navigating Through the Setup Utility on page 2 for more information). The following table

shows the names of the menu fields for the Exit menu, the default settings and a description of the field's function and any special information needed to help understand the field's use.

PhoenixBIOS Setup Utility

Main Advanced Security Boot Exit

Item Specific Help

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Discard Changes

Save Changes

Exit System Setup and save your changes to

CMOS.

F1 Help

ESC Exit

Select Item

Select Menu

-/Space Change Values

Enter Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Figure 19. Exit Menu

Table 19: Fields, Options and Defaults for the Exit Menu

Menu Field

Exit Saving

Changes

Exit Discarding

Changes

Load Setup

Defaults

Discard Changes

Save Changes

Description

Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory and then exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes]

[No] will be displayed.

Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the

BIOS recognizes this selection it will load the operating system and begin operation.

Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message

Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit

Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.

Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load previous now? [Yes] [No] will be displayed. When confirmed the utility will return to the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility Section.

Selecting Save Changes causes the new settings in all menus to be written to the BIOS memory. The message Save configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to the Exit menu. To go to another menu, follow the directions in the Navigating Through the Setup Utility section.

28

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Windows 10 IoT Enterprise
  • Intel Celeron J4125 (2GHz)
  • 4GB (2400MHz) DDR4-SDRAM & 128GB SSD

Related manuals