FA Integrated Tool Package - OMRON Industrial Automation

FA Integrated Tool Package - OMRON Industrial Automation
FA Integrated Tool Package
One software for your complete machine
Easy, Intuitive Programming Software
Structured Text for Simple programming
Easy Input - Easy Designing - Easy Validation
Further Advanced Integrated Tool Package CX-One Version 4
ST programming for further easy and
simple programing and configuration
of PLC systems
The CX-One is an integrated package of Support Software including setup applications for networks, PTs, Servo
Drives, Inverters, and Temperature Controllers as well as programming software of PLCs.
CX-One Tools
Network Settings
Programming/Simulation
Programmable Terminal
Screen Creation
Motion Control
PLC-based Process Control
CJ1
Loop Controller
Serial
Creation of
Protocol
Macros
Network between PLCs
Generic External
Devices
NX-IO Configurator
EtherNet/IP Coupler Unit
NX I/O Unit
CX-ConfiguratorFDT
IO-Link
IO-Link device
Remote I/O Terminals Temperature Controllers
Remote I/O Terminals Smart Slice
Network Settings
Temperature
Controller Settings
Inverter
Servomotor
Servomotor
Inverter
Servo/Inverter Settings
Microsoft, Visual Basic, Visual C#, Visual Studio, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.
DeviceNet™, DeviceNet™ Safety, CompoNet™, and EtherNet/IP™ are either registered trademarks or trademarks of ODVA.
Other company names and product names in this document are the trademarks or registered trademarks of their respective companies.
2
CX-One
Ver.4
Easy Programming
New Support Software
NX-IO Configurator and CX-ConfiguratorFDT are added
The NX-IO Configurator is software to set up EtherNet/IP Coupler Units and NX-series I/O Units on an EtherNet/IP Coupler Unit.
The CX-ConfiguratorFDT is software to set up IO-Link devices connected to an IO-Link Master Unit on an EtherNet/IP coupler Unit.
These software allow you to configure the Units and devices from a computer connected to a CS/CJ-series CPU Unit.*
Reusable Designs
Support for New Operating System
Windows 10 is supported
Position Control
In addition to Windows XP, Vista, 7, 8, and 8.1, Windows 10 is now supported.
The CX-One runs on the Windows 10 desktop.
OS *
Windows XP (Service Pack 3 or higher, 32-bit version) / Windows Vista (32-bit/64-bit version) / Windows 7 (32-bit/64-bit version)
/Windows 8 (32-bit/64-bit version) / Windows 8.1 (32-bit/64-bit version) / Windows 10 (32-bit/64-bit version)
Network
CX-One Lite is available on DVD
The FA Integrated Tool Package CX-One Lite suitable for Compact PLCs is now available on one DVD instead of four CDs.
Debugging
Component Tools
FA Communications Software
Online Web Services
Resume Function for Automatic Update
Ordering Information
The auto update function using OMRON Automation Upgrade Utility allows you to suspend and resume downloading the version upgrade
program. When a download is arbitrarily interrupted or connecting to the server fails during a download, the download can be resumed from
the point where it was suspended.
CX-One Lite
The download can be suspended.
Click the Install Button again.
The download resumes from the point
of suspension.
* The NX-IO Configurator runs on Windows 7 SP1, 8, 8.1, and 10.
3
Easy Programming
Steps Required to
Input Ladder Diagrams
Reduced 50%
Note: In comparison to
CX-Programmer version 8.
Input without Wasted Effort !
Use Mnemonics to Input Instructions Directly or Use 1-key Inputs
A Smart Input Function Greatly Reduces
the Work Required to Input Programs
A new method is available that lets you input instructions directly using mnemonics.
Other functions include automatic addresses for operands, including input bits and output bits, automatic insertion of connecting
lines for output and application instructions, and other smart input functions that greatly reduce the work required to input ladder diagrams.
*This function is supported only for ladder diagrams.
Instruction and Address Input Assistance
When you begin typing an instruction from the keyboard while in the Ladder Editor Window, suggested instructions are displayed.
All you have to do is select the instruction from the list for easy input even if you do not remember the entire mnemonic.
Suggested instructions displayed
Automatic Insertion of Connecting Lines
When an output or application instruction is input, the required connecting line is inserted automatically starting at the cursor location.
This greatly simplifies the work required to insert lines.
A vertical
connecting
line is created
upward from
the cursor
location
Address Incremental Copy
To create the same group of ladder instructions more than once, the address incremental copy function can be used to reuse the instructions
simply by inputting an address offset.Also, address offsets can be set individually and I/O comments can be created automatically.
4
CX-One
Ver.4.0
Easy Programming
Auxiliary Bit Input from Lists
Clock Pulse Flags, Condition Flags, and other special bits in the Auxiliary can be selected from lists, eliminating the need to remember addresses.
Reusable Designs
Position Control
The more frequently used flags
appear at the top
Network
Address Incrementing
Debugging
The address of the next operand, including input bits and output bits, is incremented by one and displayed as the default.
This enables easily inputting consecutive addresses.
Component Tools
The previously input address (CIO 0.00) is automatically
incremented by one and displayed as the default operand.
FA Communications Software
Online Web Services
Quick-key Input of Both Instruction and Operands, and Consecutive Input of Instructions
When an instruction is displayed with a default operand, just press the Shift + Enter Keys to confirm input of both the instruction and operand.
To input the same instruction consecutively, just press the Ctrl + Enter Keys.
We've eliminated the number of steps for key operations wherever possible.
Ordering Information
CX-One Lite
Quick-key Input of Both Instruction and Operands
Consecutive Input of Instructions
5
Easy Programming
Easily Program Numeric Calculations and Text String Operations with Structured Text
Structured Text for Simple and
Easy-to-understand Programming
Structured Text (ST)
Numeric calculations, conditional branching, and text string processing, all of which can be difficult with ladder diagrams,
can be easily programmed using ST.
Calculating the Length and Angle from X,Y Coordinates Using Numeric Calculations and Conditional Branching
Ladder Diagram
Structured Text
• Work memory is required to temporarily hold the
• Work memory, which is required for the ladder diagram,
• The control data for each instruction must be
• The calculations can be written in numeric form.
calculation results.
understood and suitable numeric values must be set.
• The calculations cannot be written as formulas.
is not required.
• It is not necessary to understand the special ladder instructions
of each manufacturer or the control data for the instructions.
Collecting Date Information from the PLC Using Text String Operations
Ladder Diagram
Structured Text
• Work memory is required to join the text strings.
• Work memory, which is required for the ladder diagram, is not required.
• Text string processing is complex and difficult to
understand.
6
• Text string processing can be handled in a high-level programming language.
CX-One
Ver.4.0
Easy Programming
Reusable Designs
Input Assistance on ST Editor
When you type the first letter of a statement, function, or symbol on the ST Editor, the keyword list is displayed. You do not have to type it all out.
Position Control
Type the first
letter.
Network
Press the Tab key to automatically insert
the syntax. You can easily input even if
you do not remember the exact syntax.
Debugging
The list of statements, functions, and
symbols is displayed. Just select one
from the list to input, which reduces
input errors.
Component Tools
Function Guidance on ST Editor
By hovering your mouse over a function, the tool tip will display the function name, arguments, and return values.
This guidance will help you program without a manual.
FA Communications Software
When you input a function or hover your mouse
over it, the tool tip will display its descriptions.
You can program without a manual.
Online Web Services
Symbol Definition Assistance on ST Editor
Ordering Information
If entering an undefined symbol, you will see a mark under the symbol.
You can add a new symbol from the dialog box even during programming.
Set items and click the OK button.
CX-One Lite
A mark appears under the
undefined symbol. By hovering
your mouse over this mark,
a button will be displayed.
Press the button to display
a dialog to add a new symbol.
Note. These functions are available in the CX-Programmer version 9.3 or higher.
7
Reusable Designs
Modular Function Blocks (FB) and Easy-to-read Structured Text (ST)
FB and ST Facilitate the Reuse
of Program Designs
The multilingual feature supports IEC 61131-3. Programming is possible in a language that is appropriate for the process by combining ladder diagram and ST
languages. Function blocks can be created to make programming even more efficient.
Ladder diagram:
Controla the equipment and
external devices.
User program
FB
Task
a : = a + 1;
RESULTS=0.0;
Task
IF M=TRUE THEN
RESULTS=SIN(date):
ENDIF;
Task
Task
Function Block (FB) :
Can be used and reused
as modules.
Structured Text (ST) :
Simplities math calculations
and character string
processing.
Sequential Function
Charts (SFC):
Controls the steps
in processing.
A programming language sultable for the process can
be used.
8
CX-One
Ver.4.0
Easy Programming
Support for Data Structures, Timer Data Type, and Counter Data Type
Reusable Designs
Newly Supported Data Types Make
Reusing Program Designs Much Easier
Applicable Models
: CJ2
CJ2
Data Structures
A data structure is a user-defined data type that groups various data together. By grouping the data, large volumes of
data handled by a program are made easier to understand and can be registered or changed much easier.
Position Control
Data can be easily reused as one entity.
If the same pattern is repeated
in the data, you can define a data
structure to enable easily reusing
the data in programming.
Motor 1
Motor
Operation command
Frequency command
Acceleration time
Deceleration time
Acceleration time
Motor 2
Deceleration time
Operation command
Frequency command
Acceleration time
Deceleration time
The same data structure is used.
This group of symbolscan be easily reused.
Debugging
Structure definition
Network
Operation command
Frequency command
Component Tools
Data can be easily changed.
Motor 1
Motor
Operation command
Operation command
Frequency command
Frequency command
Acceleration time
Deceleration time
For example, you can delete
the "frequency command"
member of the data structures.
Structure definition
FA Communications Software
Even if there are changes to the
data, the definition of the data
structures can be modified to
automatically change the data
structures symbols in the
symbol table as well.
Acceleration time
Deceleration time
Online Web Services
The change is automatically applied to
the data structures symbols as well.
Ordering Information
Timer and Counter Data Types
The timer and counter data types can now be used in ST. This enables using timers in ST to perform wait processing.
Example of Processing after a Specified Period of Time Elapses
100-MS
TIMER
CX-One Lite
TIMX(In1, My Timer, 50);
timer set value
timer address
execution condition
The addition is executed when the Completion Flag (CF)
of MyTimer turns ON in 5 seconds.
9
Position Control
Improved Functionality for Position Control
Preliminary Verification of Memory Operation
for Position Control
Applicable Models : CJ1W-NC
4/NC 81
Use Memory Operation Previews for Smoother Startup
Verifying operation before transferring the memory operation data to the Unit enables smoother startup and reduces the work involved in system verification.
Display graphs of positions or
speeds against time.
Easily compare results to data tables using
sequence numbers displayed in the graph.
Display Axis Movement Patterns for Two Interpolated Axes or for All Axes
You can verify movements by axis for each task. (Up to four axes can be displayed for each task.) Just click to switch the frame of reference for
confirming operating patterns between one/two-axis interpolation, all axes, and pulse output instructions.
Displaying Two Interpolated Axes
Displaying the
movement for two-axis
interpolation enables
visually verifying the
interpolated operation,
which is very difficult to
imagine with table data.
A pointer moves on the
movement pattern when
it is replayed.
This enables preliminary
verification of
movements.
10
Displaying All Axes
Displaying timing changes
side by side for changes in
position or speed over time for
all of the axes lets you verify
the timing of operations.
CX-One
Ver.4.0
Applicable Models : CJ1W-NC�81
Setup the Position Control Units and Servo Drives from One Connection
Just connect the computer to a CPU Unit port to set up the Position Control Units with EtherCAT interface and EtherCAT communications.
You can also directly start the CX-Drive Support Software to set the Servo Drives connected to the Position Control Units.
Reusable Designs
Easily Achieve Position Control without
Wading Through User Manuals
Easy Programming
Position Control Unit and Communications Setup Integrated into the CX-Programmer
Position Control
Position Control Units
with EtherCAT interface
Network
Debugging
The communications parameters for Position Control Units with EtherCAT interface can be set simply by selecting a menu command.
FA Communications Software
Automatic Network Setup
Component Tools
AC Sarvo Drive
R88D-KN�-ECT
Online Web Services
Ordering Information
CX-One Lite
After automatically setting the network,
you can immediately transfer the parameters
for the Position Control Unit.
11
Network
USB and EtherNet/IP Ports Are Available for CJ2 CPU Units
Easier Connection to PLCs
Applicable Models : CJ2
Easy Connection with USB
A standard USB cable can be easily connected to the USB port on the front of the CPU Unit.
Standard USB cable
Standard-feature
USB port
CX-One
( Example:CX-Programmer)
Easy Connection with EtherNet /IP
Easy connection by specifying the computer LAN ( Ethernet) port and IP address only.
*CJ2(built-in EtherNet/IP) CPU Units only.
EtherNet/IP
CX-One
( Example:CX-Programmer)
HUB
192.168.250.13
192.168.250.14
192.168.250.15
Prevent Connection Errors by Verifying PLC Names
The CJ2 CPU Unit can record a PLC name. Errors in transfers can be prevented ahead of time because
the PLC name can be compared with what is in the project file when connecting online.
Online connection
HUB
PLC name
Equipment_A
Browse and Connect from
the EtherNet/IP Connection List
PLC name
Equipment_B
PLC name
Equipment_C
Select a PLC from the list to connect to it.
Even if the IP address is unknown, you can browse a
list of PLCs connected to the EtherNet/IP and select
one to connect to it. With this, remote debugging
and maintenance can be conducted smoothly on site.
*CJ2(built-in EtherNet/IP) CPU Units only.
12
The PLCs connected to the EtherNet/IP network
are automatically detected.
Simply select from the list of PLCs and connect.
CX-One
Ver.4.0
Easy Setting of Tag Data Links for EtherNet/IP
*CJ2(built-in EtherNet/IP) CPU Units only.
Reusable Designs
In addition to creating data links with the EtherNet/IP Datalink Tool using I/O memory addresses, you can also use network symbols for tags to
easily create the data links.
With EtherNet/IP, high-speed, high-volume data links can be created with different cycle specifications for each applications, regardless of the number of nodes.
Easy Programming
Integration of Network Construction and Parameter Settings
Position Control
Network
Remote I/O Terminals
Smarts Slice
Component Tools
A wizard can be used to easily set the tag data
links for Ethernet/IP by importing the network
symbols for tags from the CX-Programmer.
Remote I/O Terminals
Debugging
EtherNet/IP Tag
Data Link Setting Wizard
Temperature Controllers
FA Communications Software
Ordering Information
EtherNet/IP data links can be easily
created by setting I/O memory addresses
in data link tables.
Online Web Services
EtherNet/IP
Datalink Tool
CX-One Lite
13
Network
NX-IO Configurator
CX-ConfiguratorFDT
Integrated Configuration of EtherNet/IP Coupler Units, NX-series I/O Units,
and IO-Link Devices
NX-series I/O Unit Setup from a
Computer Connected to a CPU Unit
Configuration of EtherNet/IP Coupler Units and NX-series I/O Units
You can configure and maintain EtherNet/IP Coupler Units and NX-series I/O Units
on an EtherNet/IP Coupler Unit.
The NX-IO Configurator included in the CX-One enables configuration
from a computer connected to a CS/CJ CPU Unit.
A computer can be connected directly to a Switching Hub via Ethernet.
Configuration of IO-Link Devices
You can configure IO-Link devices connected to an IO-Link Master Unit
on an EtherNet/IP Coupler Unit.
The CX-ConfiguratorFDT included in the CX-One enables configuration
from a computer connected to a CS/CJ CPU Unit.
CJ2/CS1
NX-IO Configurator
EtherNet/IP Coupler Units
NX-series I/O Units
IO Link Devices
IO-Link
Note: The Sysmac Studio or Sysmac Studio NX-I/O Edition is required to
use the NX-series Safety Control Unit.
Downsize machines and control panels
NX-series I/O System Catalog
R183
14
CX-ConfiguratorFDT
Improve equipment operation rate
IO-Link Series Catalog
Y212
Network
CX-One
Ver.4.0
Total Diagnosis of a Controller Link
Network Status Diagnosis
Data link is
inactive.
Position Control
The network status diagnosis results show the status of the specified Controller Link network (transmission path type,
baud rate, communications cycle time, data link status (automatic/manual, active), polling node, and starting node) and
the status of the nodes participating in the specified Controller Link network (participating in data links, errors, names, etc.).
Any differences between the nodes registered in the specified node file and the actual nodes will be displayed.
The operating status of the CPU Units and Controller Link Units/Boards is checked. Error information will be
displayed if any errors occur.
Reusable Designs
The Controller Link Network Diagnostic Tool can check the network status, node status, node settings, disconnections, and transmission status.
This tool can be started from the CX-Integrator.
Easy Programming
Monitors Nodes on Controller Link Network, Suggests Troubleshooting Measures,
and Checks Errors in Settings
Node icon
Name that is
specified
in the node file
Indicates that the node is
participating in data links
Network
Node address
Indicates that terminating
resistance is ON
The diagnosis result is displayed here.
Double-click to display details.
Node Settings Diagnosis
Error and Warning
are detected.
Online Web Services
The settings in the DM parameter area and other settings of all nodes participating in the specified
network are read, and the integrity of the overall network is checked.
The diagnosis results are displayed in three levels: Error, Warning, and Information.
FA Communications Software
Probable causes
and measures
Component Tools
Error details
Debugging
Indicates that error occurred.
(The background is red.)
Ordering Information
CX-One Lite
Results are displayed here.
Error Log Collection
The error status and error logs for all nodes on the specified network can be collected and stored in one file.
This function enables sending files collected on remote systems as email attachments for later analysis.
15
Debugging
Comprehensive Debugging for Networks
Time Required for Onsite Startup and
Debugging Has Been Significantly Reduced
With CX-One version 3.0, debugging is efficient with simultaneously monitoring and management of multiple networks and PLCs.
Management of Multiple Networks
The operation of networks with configurations consisting of
multiple networks including PLC networks such as
EtherNet/IP™ and Controller Link, field networks such as
DeviceNet™ and CompoNet™, and networks for Programmable
Terminals and Serial Devices, can be restored simultaneously
from the CX-One. Onsite start up and debugging can be
conducted efficiently and without errors because PLCs
and devices can be selected from the window to transfer
programs and parameter data to the computer during
operation.
Ladder Diagram Monitoring for
Multiple PLCs
Multiple PLCs can be monitored by displaying them in series on the screen. This way it is easy to debug data links between PLCs and monitor the
inputs and outputs of different PLCs.
PLC1
PLC2
PLC3
Node 1
Node 2
Node 3
Group Monitoring of Multiple PLC Input/Outputs in the Watch Window
The desired I/O data can be selected for multiple PLCs, such as input bits, output bits, and word I/O data, and monitored simultaneously. There
are also functions such as the Binary Monitor and Forced Set/Reset functions that enables graphical monitoring the ON/OFF status of word data.
All of these monitoring functions are easy to use.
Addresses that
you want to
monitor can be
registered for
each debugging
segment.
16
CX-One
Ver.4.0
Functionality and operability has been significantly upgraded compared to the previous data trace function. The new data trace function provides
comprehensive debugging, such as I/O comment display of sampled addresses, specification using symbols, checking the measurement time between
two selected points, and layering waveforms. Furthermore, data sampled from the CPU Unit’s trace memory can be saved to a file on the computer at
� Data Trace Function
Sampled values from a specific
word will be displayed.
� Continuous Data Trace
Applicable Models : CJ2
Logging
First
Second
Third
Sampled value from a
specific input bit will be
displayed.
CJ2
Programs can be debugged using a computer without the actual PLC. A wide range of languages, such as ladder diagram, sequential function
force-set/reset, breakpoints can be set, and a PLC error simulator can be used.
� Simulation of SFC, Ladder Diagrams, and Function Blocks
Forced set/reset
Ordering Information
Can be used for SFC steps
and transitions.
Breakpoints
CX-One Lite
Breakpoints can be inserted
anywhere in the program,
such as for input bits,
output instructions, special i
nstructions, or function blocks.
Breakpoints
No Size Restrictions for Online Editing of Function Blocks and
Sequential Function Charts
There are no size restrictions for the function blocks and SFC that can be edited online.
Online Web Services
Error Simulation
It is easy to debug errors that are difficult
to generate with the actual PLC. Debug
contents can be saved and used in test
document.
FA Communications Software
charts (SFC), structured text (ST), and programs within function blocks are supported. Furthermore, programs can be edited online, bits can be
Component Tools
Simulation Debugging
Debugging
The traced waveforms can be displayed as layers.
High-speed sampling to the
PLC trace memory
Network
Data is collected in the computer
at a specified interval
Position Control
The CJ2 CPU Units can trace data for long periods of time.
Data can be saved in CSV files.
Reusable Designs
a specified frequency. This can be used as for long-term logging of data.
Easy Programming
Time Require for Debugging and Maintenance Has Been Reduced with
the Comprehensive Data Trace Function
Applicable Models : CJ2
17
Debugging
View and Change Values of PLC I/O Memory with Comments
The SwitchBox Utility helps you debug PLCs by allowing you to monitor and change values of I/O memory in CPU Units.
This utility software displays values of I/O memory (words and bits) with comments on a PC.
Function keys can be used to set/reset bits, force-set/force-reset bits, select a monitored group, and work the CX-Simulator.
Bits and words to monitor can be registered as an address group. You can easily change the addresses to monitor
by selecting a registered address group. Up to 100 address groups can be registered.
The SwitchBox Utility can import addresses with I/O comments from the memory card mounted to the PLC,
global symbol table of the CX-Programmer, tab-delimited text file, or clipboard.
It can also export addresses with I/O comments to a tab-delimited text file or clipboard.
Address group
(Group to monitor)
Bit Monitor
(Monitors 14 selected bits)
Bit Monitor Window
(Monitors 6 words)
Watch Monitor
(Monitors 14 selected words)
Bit Monitor Window (Monitors 4 words)
Function keys to select functions
PLC Backup Tool Batch Backup
Batch Backup/Restore with a Computer
A computer can be used to backup, compare, or restore data for all or specific PLC Units when connected online. Backup information is automatically tagged
with a date stamp. It is thus possible to return to the state before an error occurred. It is also easy to identify the file for restoring data when an error occurs.
Specified backup
destination folder
PLC Backup
Software
CS/CJ-series PLC
(CPU Unit + Configuration Units)
Restore
Compare
Backup
Easy Online Connection
With the improved automatic online connection function, all you need to do is
select the PLC series to connect.
There is no need to set the PLC model and protocol, greatly reducing setting
time.
18
Component Tools
CX-One
(Screen Designing)
Ver.4.0
The time required for designing can be significantly reduced because of the compatibility with CJ-series
PLCs. The process of designing screens is easier with expanded function.
Applicable Models :
NS Series NSJ Series
Test functions for the CX-Designer and CX-Programmer are linked through the CX-Simulator on a computer. This enables screens and ladder diagrams to be
checked simultaneously, significantly improving the debugging efficiency. A new Integrated Simulation Button has been added to the CX-Programmer.
Furthermore, work efficiency has been significantly improved with the function that enables work windows to be pinned in front, and a flexible zoom function.
Position Control
Integrated Simulation with the PLC Ladder Diagrams
Reusable Designs
The CX-Designer Simplifies the Processes from Screen
Design to Debugging for the NS-series Programmable Terminals
Easy Programming
Products Are Highly Compatible and Easy to Use Because They Are from a Comprehensive PLC Manufacturer
Screens and Ladder Diagrams Can Be Simultaneously Checked on a Computer
Touch Panel Screen
Linked
Network
Ladder Diagram Window
Single-key Simulation
Debugging
Within computer
Component Tools
Special function which can be used for a system with Omron PLC CJ2 and NS-series programmable terminal.
Just drag the data structures on the CX-Programmer and drop it on the CX-Designer.
Note1: To use CJ2 data structure, prepare CX-Designer Ver.3.2 or higher and NS system program Ver.8.4 or higher.
Note2: This function can be used when the PLC and programmable terminal are connected via EtherNet/IP.
CX-Programmer
CX-One Lite
Drag
and
drop
Ordering Information
CX-Designer
Online Web Services
Data structures can be shared between the PLC ladder program and screen editor of programmable terminal.
FA Communications Software
Using CJ2 Data Structures Can Improve System Design Efficiency
19
Component Tools
(Screen Designing)
Communications Components and the Smart Active Parts(SAP)Library Significantly
Reduces the Time Required to Create Ladder Diagrams and Screens
There are over 3,000 Smart Active Parts that can directly access OMRON PLCs and components. Simply select and paste a part from
the SAP library onto the screen. Detailed screens and ladder diagrams do not need to be created.
SAP Library of Temperature
Controller Components
Screen Designing Tools
CX-Designer
Using Software Components, Error Checking and
Parameter Setting Can Be Done without a Computer
There are many software components in the Software Function SAP Library that
can be easily incorporated into the NS-series Programmable Terminals. Simply
select and paste software components on the screen. Device errors can be
checked and parameters set without a computer.
Drag
and
drop
FROM
Computer Software
TO
EASY Tools (Software Function SAP Library)
Transfer
Immediate creation of
Temperature Controller
Settings and Monitor Screens
CJ2
E5AC
PLC CPU Unit
Monitor Screen
NCF Unit
Setting Screen
EJ1
MX
DeviceNet Monitor Screen
The Troubleshooter SAPs Can Be Used Onsite without Computers or Manuals
There is a troubleshooter SAP library that covers all PLC Units. If there is a PLC error, the troubleshooter SAP library explains the cause and
how to implement countermeasures in a way that it is easy to understand.
Improved Troubleshooter
SAP Library
Position Control Unit Troubleshooter SAP
20
Basic I/O Unit Troubleshooter SAP
In addition to the DeviceNet Units and Position
Control Units, the CX-Designer also includes Basic
I/O Unit, Analog I/O Units, Serial Communications
Units, High-speed Counter Units, Controller Link Unit,
and ID Sensor Units. Including the EtherNet Units
and Motion Control Units is planned in future
development stages.
Component Tools
CX-One
(Motion Control)
Support from system starting to Maintenance. Also Provides EtherCAT Compatibility
Parameters
Servo Drive or Inverter parameters can be set as easily as with a
digital operator. With an EtherCAT system, Servo Drive parameters
can be set and status can be monitored through the PLC.
USB
CJ Series
Position Control Units
with EtherCAT interface
You can also
connect the
CX-Drive to G5-series
Servo Drives directly
with USB.
Simple FFT
OMNUC G5 Series
AC Servo drive with built-in
EtherCAT communications
Simple Gain Adjustment
Measurement, Analysis, and Monitoring
Status Monitoring
Data traces can be used to monitor the speed or torque as easily
as with an oscilloscope.
Debugging
Simple FFT
You can measure the frequency characteristics of the system
and diagnose resonant frequencies. Apply the notch filter to
resonant frequency to achieve higher responsivity.
Stand alone CX-Drive (WS02-DRVC1) version is Ver.2.92.
Component Tools
Quickly adjust the gain using a wizard.
FA Communications Software
The autotuning feature provided with the CX-Drive makes it easy to adjust the Servo Drive gain.
You can use a wizard to complete gain adjustment in approximately five minutes or less per axis
simply by selecting the machine configuration and entering the target set time.
Autotuning
Online Web Services
Although previously the machine configuration was set using parameters,
it can now be selected from ball screws, turntables, belts, and other devices.
Automatic Adjustment
Setting for automatic adjustment and conditions after completing
automatic adjustment.
Ordering Information
Gain adjusted in 5 minutes per axis.
Machine Configuration
Autotuning
Implement auto-tuning until reaching to a target value.
Stabilization time, overshooting amount and efective load rate can be monitored.
CX-One Lite
Autotuning Completed
After completing autotuning, the results can be checked
using the data tracing.
Applicable Models : Servo G5/G/W Series
SMARTSTEP 2/SMARTSTEP Junior/SMARTSTEP A Series *
Network
Simple Gain Adjustment
You can use a wizard to complete gain adjustment in five minutes or
less per axis simply by entering the machine configuration and the
target set time.
Tool
Position Control
Easy Setup and Adjustment
CX-Drive
Reusable Designs
Optimum Motion System Support for Applications
with Motion Networks or Generic Interfaces
Easy Programming
Easily Built Intelligent Motion Control
Ver.4.0
Inverter MX2/MX2-V1/RX/RX-V1/JX/MX Series
3G3JV/3G3MV/3G3RV/3G3RV-V1
* Discontinuation models in March 2013.
21
Component Tools
(Motion Control)
Easy Management of Parameters While Connected to PLCs
CX-Motion-NCF
Parameters that can be edited
Settings can be modified while connected
Easily set, transfer, and verify parameters.
Position Control Unit
axis settings and
Servo Drive Parameters
Wiring can be checked while connected
Monitor status and present values.
Simultaneously monitor the Servo Drives for up to four axes.
Operation can be checked while connected
Position Control Units with MECHATROLINK-II interface
Execute servo locks, jogging, and error resetting. Display error codes and
ON/OFF status for each axis. Monitor present values and busy status.
Even Easier to Start Up a System
Applicable Models : CS1W/CJ1W-NCF71/NC271/NC471
CX-Motion-MCH
Programming Is Easy
Easily set, transfer, and verify tasks and axis parameters.
Perform syntax checks for motion programs.
Debugging Programs Is Easy
Execute servo locks, jogging, stepping, origin searches, origin returns,
force-setting the origin, error resetting, absolute origin setting, and teaching.
Display error codes and I/O ON/OFF status for each axis.
Use breakpoints to easily debug programming.
Checking Operation Is Easy
Use data tracing to trace variables in the Motion Control Unit.
Display the results in graphs to easily check operation and make adjustments.
22
Debugging motion programs
Data trace results
Insert a breakpoint
where you want to
pause the program
Variable values
can be
changed
Motion Control Units with MECHATROLINK-II interface
Applicable Models : CS1W/CJ1W-MCH71
Component Tools
(Temperature Controllers)
CX-One
Ver.4.0
CX-Thermo
Setting Temperature Controller Parameters Is Easier
CX-Thermo
Parameter
Property
Window
Work
space
Easy Parameter Settings
Parameters can be set even for Temperature Controllers that
do not support communications.
Parameters can be saved, and then copied, or reused and edited
(Parameters can be exported in CSV or HTML format.)
Position Control
Parameters can be easily set from a list
Reusable Designs
The CX-Thermo/CX-Process Tool Software Supports
High-level Temperature Control
Easy Programming
From Parameter Settings to Temperature Data Management
Displays Only What Is Used
* Discontinuation models.
Component Tools
Programming for the Process Controller Is Easier
Parameter
List
CX-Process Tool
Control Programs Can Be Constructed By Pasting Function Blocks
Control programs can be constructed by pasting function
blocks and connecting them. They can be used for simple PID
control, program control, and cascade control.
Applicable Units :
CJ1G-CPU4 P/CPU4 P-GTC,
CS1W-LCB01/LCB05/LCB05-GTC,
CS1W-LC001 *,CS1D-CPU6 P
* Discontinuation models in March 2012.
Adjusting Parameters While
Monitoring Trends
PID parameters can be adjusted while
monitoring the present value (PV), setting point
(SP), and manipulated variable (MV). Trend data
can be saved in CSV format.
(CX-Thermo Trend Viewer, CX-Process Tool Support
Software Tuning Screen)
Controlling with a Reliable Control Algorithm
(See note.)
The execution of the autotuning (AT) function that calculates the PID constants and the fine
tuning (FT) function that improves controllability exactly as required are made easy with an
intuitive user interface. The interference overshooting adjustment function is supported to
adjust overshooting when interference occurs, and the gradient temperature control function
achieves constant internal temperatures for multi-point temperature control with interference.
CX-One Lite
CX-Thermo/CX-Process Tool Support Software
Ordering Information
Output
Window
Screens for the NS-series PTs (NS runtime screen) are
automatically generated from the function block programs.
Standard control screens and tuning screens do not need to be
created manually.
Online Web Services
Project
workspace
Easy Creation of an HMI
FA Communications Software
Control Can Be Customized
CoZrams, etc.)
Debugging
Output
Window
Applicable Units :
E5CD/E5ED/E5CC/E5EC/E5AC/E5DC/E5GN/
E5CN */E5CN-H/E5CN-HT/E5EN */E5EN-H/
E5EN-HT/E5AN */E5AN-H/E5AN-HT/E5ER/
E5ER-T/E5AR/E5AR-T/EJ1/E5ZN
Network
To avoid unintentional use of parameters, unused parameters
can be masked (i.e., hidden)
Note: Supported functions depends on the product being used. Refer to product manuals for details.
23
FA Communications Software
Note. CX-One Version 4.□ does not include CX-Compolet and SYSMAC Gateway.
Easily Write Programs to Read and Write
PLC Data with VB or C#.
CX-Compolet
User Application
CX-Compolet
VB or C#
Simply paste to the form and
specify the tags (addresses).
Easy to Use without Any Technical Knowledge
.NET
Control
Provides software components that help you easily
and quickly develop PLC communications.
Read and write PLC data without the need to
consider differences between networks.
Supports Microsoft Visual Studio 2015.
For the CJ2 (with EtherNet/IP functionality) or
NJ/NX/NY, I/O memory in the PLC can be accessed
by using tag names rather than addresses.
Array and structure variable access is possible.
Example
Example:
Reading I/O
O
Memory
SYSMAC Gateway
y
DM0
Press the button to read the
value (D0 in this example).
1234
PLC
Communications Middleware to Connect a
Computer and PLCs
Applications
SYSMAC Gateway
Direct Connection of the Industrial Ethernet: EtherNet/IP
SYSMAC Gateway
Direct Access to High-speed and
High-capacity Networks
In addition to FINS communications, SYSMAC
Gateway supports EtherNet/IP communications.
Absorbs differences in the physical layer between
RS-232C, USB, Ethernet, EtherNet/IP, and
Controller Link.
Just install the software on the computer to enable
data communications for controls and information.
Serial
EtherNet/IP
Real PLC
Real PLC
Controller Link
Real PLC
Note: Communications are possible via
USB and Ethernet too.
Product Positioning
FA Communications Software
CX-Compolet
System Application
Device-embedded Applications
CX-Compolet
(Previously called “SYSMAC Compolet.”)
Easy PLC Data Reading
and Writing with VB.NET
and C#.NET Control Objects
SYSMAC Gateway
FINS/CIP Communications Middleware
SYSMAC Gateway
24
CX-Compolet software
enables easily reading and
writing PLC data using Visual
Basic and C#.
It is the successor to
SYSMAC Compolet.
(formerly FinsGateway)
RS-232C
USB
EtherNet/IP
Ethernet
PLC
PLC
PLC
PLC
Controller Link
PLC
SYSMAC Gateway can be
used as the communications
driver on most networks. It is
the successor to FinsGateway
and has inherited all
FinsGateway functionality.
Online Web Services
Web Support Services for CX-One
Position Control
When you register online as a user of CX-One, all CX-One
software components can be registered at once. The
online registration website can be accessed from Japan,
North America, South America, Central America, Europe,
Africa, Asia, China, Taiwan, and Korea. You can access
the Internet services from anywhere once you have
registered.
Reusable Designs
Online User Registration
Easy Programming
OMRON’S CX-One offers many service options in the Internet environment so that engineers and online
support is available from anywhere in the world 24 hours a day.
Network
Automatic Update
Debugging
With the automatic update function of CX-One, the latest
update information for your computer environment can be
searched for and applied using the network environment.
Your CX-One can be constantly updated to the latest state.
It is also possible to update only the necessary tools.
Component Tools
Online Web Services
Control devices that were made available after you
purchased the Support Software can be used if you
download the latest Smart Libraries from the Internet. A
customized library can be made by downloading the
Smart FB Library and Smart Active Parts for the hardware
that you require. Programming is also easy by selecting
and pasting the necessary parts.
FA Communications Software
Download Services
Ordering Information
CX-One Lite
25
Ordering Information
Ordering Information
Product name
Specifications
The CX-One is a comprehensive
software package that integrates
Support Software for OMRON
PLCs and components.
FA Integrated Tool
Package CX-One
Ver. 4.
CX-One runs on the following OS. *1
Windows XP (Service Pack 3 or
higher, 32-bit version) /
Windows Vista (32-bit/64-bit version) /
Windows 7 (32-bit/64-bit version) /
Windows 8 (32-bit/64-bit version) /
Windows 8.1 (32-bit/64-bit version) /
Windows 10 (32-bit/64-bit version)
Number of licenses
Model
Media
− (Media only) *2
CXONE-AL00D-V4
1 licenses
CXONE-AL01D-V4
3 licenses
CXONE-AL03D-V4
10 licenses
Standards
CXONE-AL10D-V4
DVD
−
30 licenses
CXONE-AL30D-V4
50 licenses
CXONE-AL50D-V4
Unrestricted *3
(Site license)
Ask your OMRON representative
for details.
1 licenses
CXONE-AL01D-V4-UP
3 licenses
CXONE-AL03D-V4-UP
10 licenses
The upgrade versions *4
DVD
CXONE-AL10D-V4-UP
−
30 licenses
CXONE-AL30D-V4-UP
50 licenses
CXONE-AL50D-V4-UP
Unrestricted *3
CXONE-ALXXD-V4-UP
*1 The NX-IO Configurator runs on Windows 7 SP1, 8, 8.1, and 10.
It cannot be installed on Windows XP, Vista, and 7 without Service Pack.
*2 The CXONE-AL00D-V4 contains only the DVD installation media for users who have purchased the CX-One Version 4.
license number. Enter the license number of the CX-One Version 4. when installing.
(The license number of the CX-One Version 3. or lower cannot be used for installation.)
*3 This is a site license for users who want to use CX-One on many computers.
- The number of users is unrestricted for the same company and site.
- Only one license number must be managed.
- All computers that use the site license can take advantage of automatic updates and software downloads.
*4 The upgrade versions are for customers that already have CX-One Version 3. or lower.
and does not include the
System Requirements
Item
Requirement
Operating system (OS) (See note1,2.)
Windows XP (Service Pack 3 or higher, 32-bit version) / Windows Vista (32-bit/64-bit version) / Windows 7 (32-bit/64-bit version) /
Windows 8 (32-bit/64-bit version) / Windows 8.1 (32-bit/64-bit version) / Windows 10 (32-bit/64-bit version)
CPU
Processor recommended by Microsoft.
Memory (See note3.)
Memory recommended by Microsoft.
Hard disk
Approx. 4.0 GB or more of available memory is required to install all of the CX-One.
Display
XGA (1024×768), High Color (16-bit) or higher
Disk drive
DVD-ROM drive
Communications ports
RS-232C port, USB port, or Ethernet port (See note4.)
Other
To register online as a user using the Internet, hardware for a connection (such as a modem)
and access to the Internet are required.
Note1. CX-One Operating System Precaution :
System requirements and hard disk space may vary with the system environment.
2. Restrictions apply to operation of some applications when CX-One is used with Microsoft Windows Vista / Windows 7 / Windows 8 / Windows 8.1. /
Windows 10 (32-bit/64-bit version)
Restrictions apply to operation of some applications. Refer to the Setup Manual for details.
3. The amount of memory required varies with the Support Software used in CX-One for the following Support Software. Refer to user
documentation for individual Support Software for details.
CX-Programmer, CX-Designer, CX-Thermo, CX-Simulator, CX-Protocol, CX-Motion, CX-Drive, CX-Process Tool,
and Faceplate Auto-Builder for NS.
4. Refer to the hardware manual for your PLC for hardware connection methods and cables to connect the computer and PLC.
26
CX-One
Ver.4.0
Support Software in CX-One Version 4.
The following tables lists the Support Software that can be installed from CX-One
Outline
Application software to simulate CS/CJ/CP/NSJ-series CPU Unit operation on the computer to debug PLC programs
without a CPU Unit.
CX-Position
Application software to create and monitor data for CS/CJ-series Position Control Units.(except for High-speed type)
CX-Motion-NCF
Application software to create and monitor data for CS/CJ-series Position Control Units with MECHATOLINK-II (NC 71).
CX-Motion-MCH
Application software to create data and motion programs and to monitor data for CS/CJ-series
Motion Control Units with MECHATOLINK-II (MCH71).
CX-Motion
Application software to create data for CS/CJ-series, C200HX/HG/HE, and CVM1/CV-series Motion Control Units,
and to create and monitor motion control programs.
CX-Drive
Application software to set and control data for Inverters and Servos.
CX-Process Tool
Application software to create and debug function block programs for CS/CJ-series Loop Controllers (Loop Control
Units/Boards, Process Control CPU Units, and Loop Control CPU Units).
Faceplate AutoBuilder for NS
Application software that automatically outputs screen data as project files for Ns-series PTs from tag information in function
block programs created with the CX-Process Tool.
CX-Designer
Application software to create screen data for NS-series PTs.
NV-Designer
Application software to create screen data for NV-series small PTs.
CX-ConfiguratorFDT
Application software for setting various units by installing its DTM module.
CX-Thermo
Application software to set and control parameters in components such as Temperature Control Units.
CX-FLnet
Application software for system setting and monitoring of CS/CJ-series Fl-net Units.
Network Configurator
Application software to set up and monitor tag data links for CJ2 (Built-in EtherNet/IP) CPU Units and EtherNet/IP Units.
NX-IO Configurator
Application software to set up and maintain EtherNet/IP Coupler Units and NX-series I/O Units on an EtherNet/IP Coupler Unit.
CX-Server
Middleware necessary for CX-One applications to communicate with OMRON components, such as PLCs, Display Devices, and Temperature Control Units.
Communications Middleware
Middleware necessary to communicate with CP1L CPU Units with built-in Ethernet port.
PLC Tools
A group of components used with CX-One applications, such as the CX-Programmer and CX-Integrator. Includes the following:
I/O tables, PLC memory, PLC Setup, Data Tracing/Time Chart Monitoring, PLC Error Logs, File Memory, PLC clock, Routing Tables, and Data Link Tables.
CX-One Lite
CX-Simulator
Ordering Information
Application software to create protocols (communications sequences) between CS/CJ/CP/NSJ-series or
C200HX/HG/HE Serial Communications Boards/Units and general-purpose external devices.
Online Web Services
CX-Protocol
FA Communications Software
Utility software that helps you to debug PLCs. It helps you to monitor the I/O status and to monitor/change present values within
the PLC you specify.
Component Tools
Switch Box Utility
Debugging
Application software to build and set up FA networks, such as Controller Link, DeviceNet, CompoNet, CompoWay, and Ethernet networks.
The Routing Table Component and Data Link Component can be started from here. DeviceNet Configuration functionality is also included.
Network
CX-Integrator
Position Control
Application software to create and debug programs for CS/CJ/CP/NSJseries, C-series, and CVM1/CV-series CPU Units.
Data can be created and monitored for high-speed-type Position Control Units and Position Control Units with EtherCAT interface.
Reusable Designs
CX-Programmer
Easy Programming
Support Software in CX-One
27
Ordering Information
Related Products
� FA Communications Software
Pruduct name
Specifications
Model
Standards
CX-Compolet 1
Software components that can make it easy to create programs for communications
between a computer and controllers.
This packaged product bundles SYSMAC Gateway.
Development environment:
Visual Studio 2005/2008/2010/2012/2013/2015
Development languages:
Visual Basic, C#
WS02-CPLC1
−
SYSMAC Gateway 2
Communications middleware for personal computers running Windows.
Supports CIP communications and tag data links (EtherNet/IP) in addition to
FinsGateway functions.
WS02-SGWC1
−
Note: One license is required per computer. Refer to the CJ2 CPU Unit Catalog (Cat. No. V302) for details.
1. You can also purchase the CX-Compolet without the SYSMAC Gateway. Order WS02-CPLC2.
2. SYSMAC Gateway includes Fins Gateway. A software development kit called the SYSMAC Gateway SDK is also available to write communications programs for the
SYSMAC Gateway.
Correspondence between supported OS & Connected Networks
Ethernet
Windows Vista (32bit)
Windows 7 (32bit)
Client
Server
Yes
Yes
USB
Yes
Yes
Controller Link
SYSMAC
LINK
PCI
ISA
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Windows 10 (32bit/64bit)
Yes
Yes
Yes
Yes
No
No
No
Windows Server 2003 (32bit)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
No
Windows 8 (32bit/64bit)
Windows Server 2008 (32bit)
Windows Server 2008/R2 (64bit)
Windows Server 2012/R2 (64bit)
28
EtherNet/IP
RS-232C
Yes
Windows 7 (64bit)
Windows 8.1 (32bit/64bit)
Supported OS
Ethernet
(FINS)
Yes : Supported, No : Not Supported
No
No
Yes
No
No
The Ideal Software Package for Compact PLCs
Easy Programming
Simplified setting operations are ensured by Micro PLC Edition CX-Programmer (the ideal PLC programming
software for small-scale systems), along with Support Software to set NS/NV-series PTs, Temperature
Controllers, and Servo Drives.
Reusable Designs
Position Control
Network
Debugging
Features
Component Tools
Simplified setting operations are ensured by Micro PLC Edition CX-Programmer (the ideal PLC programming
software for small-scale systems), along with Support Software to set NS/NV-series PTs, Temperature Controllers,
and Servo Drives.
Total lead time until the system is up and running is reduced.
FA Communications Software
Support Software in CX-One
The following tables lists the Support Software that can be installed from CX-One
NV-Designer
CX-Integrator
CX-Thermo
Switch Box Utility
Network Configurator
CX-Simulator
NX-IO Configurator
CX-Drive
CX-Server
Online Web Services
Micro PLC Edition CX-Programmer *
CX-Designer
Applicable models: CP1 , CPM , SRM1
The CX-One and CX-One Lite cannot be simultaneously installed on the same computer.
Product name
CX-One Lite is a subset of the complete CX-One package
that provides only the Support Software required for micro
PLC applications.
CX-One Lite runs on the following OS. *1
Windows XP (Service Pack 3 or higher, 32-bit version) /
Windows Vista (32-bit/64-bit version) /
Windows 7 (32-bit/64-bit version) /
Windows 8 (32-bit/64-bit version) /
Windows 8.1 (32-bit/64-bit version) /
Windows 10 (32-bit/64-bit version)
The upgrade versions *2
Model
Standards
Number of licenses
Media
1 license
DVD
CXONE-LT01D-V4
-
1 license
DVD
CXONE-LT01D-V4-UP
-
CX-One Lite
FA Integrated
Tool Package
CX-One Lite
Ver.4.
Specifications
Ordering Information
Ordering information
*1. The NX-IO Configurator runs on Windows 7 SP1, 8, 8.1, and 10.
It cannot be installed on Windows XP, Vista, and 7 without Service Pack.
*2. The upgrade versions are for customers that already have CX-One Version 3. or lower.
29
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is
not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,
or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with
respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
The application examples provided in this catalog are for reference only. Check functions and safety of the equipment before use.
Never use the products for any application requiring special safety requirements, such as nuclear energy control systems, railroad systems, aviation systems, medical equipment, amusement machines,
vehicles, safety equipment, or other application involving serious risk to life or property, without ensuring that the system as a whole has been designed to address the risks, and that the OMRON products
are properly rated and installed for the intended use within the overall equipment or system.
Note: Do not use this document to operate the Unit.
OMRON Corporation
Industrial Automation Company
Tokyo, JAPAN
Authorized Distributor:
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
© OMRON Corporation 2009-2017 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
CSM_13_1_0617
Cat. No. R134-E1-17
0617 (0405)(w)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement