ROP-04

Add to my manuals
4 Pages

advertisement

ROP-04 | Manualzz
SCAN
3-channel radio flush receiver
ROP-04
the technical
data
Co-operation
with EXTA FREE
transmitters
ROP-04 receiver is designed to carry out simple control functions in LED diode systems supplied with 10 ÷ 14 V DC. In connection with EXTA FREE system transmitters, it enables the realisation of the switch on/switch off function, the monostable mode, the bistable and time
modes. ROP-04 has 3 independently controlled outputs realised on MOSFET transistors. The
outputs are designed for a direct connection of LED diode products.
Characteristic features:
• cooperation with wireless EXTA FREE system transmitters,
• independent control of up to three receivers in the following modes: switch on/switch off,
monostable, bistable, time,
• 3 MOSFET type transistor outputs with a maximum capacity of 2,5 A / output,
• possibility of a direct connection of 10 ÷ 14 V DC power supply LED products to the receiver’s outputs,
• wide operation range (up to 230 m outdoors),
• small dimensions - suitable for mounting in a typical Ø60 junction box,
• low power consumption in the standby mode (0,22 W) - the receiver is used to a continuous operation.
Mounting
indoor only
Mounting in a Ø60
junction box
10 ÷ 14 V DC
3-channel
radio flush receiver
ROP-04
Zamel Sp. z o.o.
PL 43-200 Pszczyna, ul. Zielona 27, Poland
tel: +48 32 449 15 00, fax: +48 32 449 15 02
e-mail: [email protected], www.ledix.pl
CET Lighting Sp. z o.o. declares that the equipment complies with the principal requirements
and other applicable rules of the RTTE Directive.
The symbol means selective collecting of electrical and electronic equipment.
It is forbidden to put the used equipment together with other waste.
Declaration of Conformity is on www.ledix.pl
ROP-04 ENG Ver. 01
www.ledix.pl
10÷14 V DC / 0,22 W; IP20
weight: 25 g
DESCRIPTION
APPEARANCE
ROP-04 receiver is designed to carry out simple control functions in lighting installations equipped with LED diodes. This device in connection with any wireless EXTA FREE
(www.extafree.pl) system transmitter enables the realisation of the switch on/switch off
function, the monostable mode, the bistable and time mode independently for every
channel. ROP-04 is designed to a direct cooperation with any 10 ÷ 14 V power supply LED
diode lighting. The receiver has three MOSFET type transistor outputs with a maximum
capacity of 2,5 A. Small dimensions of the casing allow for a direct mounting of the receiver in the Ø60 mm junction box. The product is characterised by low power consumption. Features of the controller:
•cooperation with wireless EXTA FREE system transmitters,
•realisation of the control function in 10 ÷ 14 V power supply LED diode lighting installations,
•3 MOSFET type transistor outputs - maximum capacity of 2,5 A / output,
•the possibility of independent control of three circuits,
•multiplicity of operation modes: switch on / switch off, monostable, bistable, time,
•wide operation range (up to 230 m outdoors),
•a possibility to increase the operation range by using RTN-01 retransmitter,
•low power consumption in the standby mode (0,22 W) - a device designed for continuous operation.
TECHNICAL DATA
Nominal supply voltage:
Nominal power consumption:
Number of channels:
Maximum current in the channel:
Modes:
Control:
Radio transmission:
Transmission method:
Coding:
Maximum number of transmitters:
Range:
Time adjustment:
Ambient temperature range:
Mounting:
Casing protection degree:
Protection class:
Dimensions:
Weight:
Reference standard:
Optic signalling of the
receiver’s operation
Channel 1,2 ,3 terminals
Programming button
Power supply terminals (+, -)
DIAGRAM
Exemplary LEDIX series fittings
ZNP, ZNN or ZNM series power supply in 14 V DC version
10 ÷ 14 V DC
0,22 W
3 x MOSFET
2,5 A
Switch on/switch off, Monostable, Bistable, Time
EXTA FREE system transmitters
868,32 MHz
One-way without confirmation
Yes – transmission with addressing
32
Up to 230 m in the open area
1 s ÷ 18 h
-10 ÷ +55 oC
In a Ø60 junction box
IP20
III
47,5 x 47,5 x 20 mm
25 g
PN-EN 60669; PN-EN 60950; PN-EN 61000
230 V AC
14 V DC
MAXIMUM CURRENT CAPACITY:
Up to 25 W for LED diode products supplied with 10 V
Up to 30 W for LED diode products supplied with 12 V
Up to 35 W for LED diode products supplied with 14 V
MOUNTING
CAUTION ! The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualified electrician staff, who act in accordance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- disconnector combined to the proper circuit.
2.Check if there is no voltage on connection cables by means of a special measure equipment.
3.Connect the power supply to 230 V AC.
4.Connect the output cables with appropriate receiver’s cables in accordance with the
connection diagram.
5.Mount the controller in the Ø60 junction box.
6.Switch on the power supply from the mains.
7.Add selected transmitters to the receiver (description in the TRANSMITTERS’ PROGRAMMING section) and check if they work properly.
TIME PROGRAMMING FOR A SELECTED CHANNEL
1s 2s ns
Press PROG push-button of ROP-04 device and
then release it. LED red diode switches off and then
switches on (the signal pulsates).
Every LED diode pulse equals 1 second.
OPERATION
The device can operate in five modes for every channel:
MONOSTABLE
the relay operates only while pressing
transmitter’s push-button.
After the adjusted time is finished
(the number of LED red diode
flashes) press PROG push-button and
then release it - TIME IS ADDED
BISTABLE
(one push-button) the device changes
the relay status cyclically always after
pressing the same push-button.
Maximum time is 18 hours hours for every channel.
SWITCH ON
the device switches on after pressing the
push-button.
APPLICATION
SWITCH OFF
the device switches off after pressing the
push-button.
TIME
the device switches off according to
the adjusted time (tp), but it may be
switched off before the adjusted time
finishes. Default settings - 15 seconds.
CAUTION! The adjusted time can not be deleted.
Wall lamps and standard LEDIX series LED fittings are connected to the ROP-04 receiver.
4-channel button radio transmitter RNK-04 and a portable remote control P-257/4 cooperate with the receiver. The wall lamps are switched on in time mode (staircase function) and
LEDIX fittings in the switch on / switch of mode.
200 200 250 200 200 250 180 180 180 200 180 180 250
P-260
RTI-01
RXM-01
RCR-01
RTN-01
RNL-01
RNP-02
RNP-01
P-257/4
RNM-10
P-257/2
P-256/8
RNK-04
RNK-02
ROP-04 Symbol
OPERATION TABLE
-
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver, it is advisable
to decrease the range according to: bricks: from 10 to 40 %, wood and plaster: from 5 to 20 %,
reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %. Over- and
underground medium and high electrical power lines, radio and television transmitters, GSM
transmitters set close to a device system have also a negative influence on the range.
RADIO TRANSMITTERS PROGRAMMING
BISTABLE mode (for a selected channel):
An exemplary programming procedure with the use of P-257/2 remote control. The
procedure for the rest of radio EXTA FREE transmitters is analogous. CAUTION: Every
transmitter can cooperate with ROP-04 in a different mode, depending on how they
were added to the device. One transmitter can be added during one programming
cycle. Full memory is signalled with pulsating LED red diode.
Transmitters and time programming is done in a sequence:
Wait for about
5 sec.
Press PROG
push-button
of ROP-04 device
Wait for
about 5 sec.
Transmitters’
programming
for channel 1
Wait for about
5 sec.
Time
programming
for channel 1
Wait for about
5 sec.
Transmitters’
programming
for channel 2
SWITCH ON/SWITCH OFF mode (two push-buttons for a selected channel):
Press PROG push-button of
ROP-04 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Time
programming
for channel 3
In order to facilitate the radio transmitters’ programming, every time when we enter the
programming mode of a selected channel (or time adjustment in time mode) the load
connected to that channel is switched on. The channel switch on is connected with LED red
diode lighting (the signal is constant).
MONOSTABLE mode (for a selected channel):
Press the
transmitter’s
push-button
for a longer
time.
Press PROG push-button
of ROP-04 device for
a longer time until LED
red diode switches on
(constant signal). Next
release PROG pushbutton
Press the transmitter’s Press and release the same
push-button for a longer transmitter’s push-button.
LED red diode switches on
time. LED red diode
(the signal pulsates) and
switches on (first signal
pulsates, next the signal is next it switches off - THE
TRANSMITTER IS ADDED
constant)
Transmitters’
programming
for channel 3
Wait for about
5 sec.
Time
programming
for channel 2
Press PROG push-button of
ROP-04 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Press the same transmitRelease the
transmitter’s
ter’s push-button and
push-button. LED
release it. LED red
red diode switches diode switches on (the
on (first the signal
signal pulsates) and
pulsates, next the next it switches off - THE
signal is constant). TRANSMITTER IS ADDED.
Press and release the first
transmitter’s push-button.
LED red diode switches on
(first the signal pulsates,
next the signal is constant)
TIME mode (one push-button for a selected channel):
Press PROG push-button of
Press and release
ROP-04 device for a longer time transmitter’s push-button.
until LED red diode switches on LED red diode switches on
(constant signal). Next release
(first the signal pulsates,
PROG push-button
next the signal is constant)
Press and release the
second transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches off - THE
TRANSMITTER IS ADDED
Press and release the same
transmitter’s push-button.
LED red diode switches on
(the signal pulsates) and
next it switches off - THE
TRANSMITTER IS ADDED
RADIO TRANSMITTERS DELETION
Press PROG push-button
of ROP-04 device for
a longer time.
After 5 seconds LED red
diode switches on (the
signal pulsates) and then it
switches off.
Release the push-button
in ROP-04 - MEMORY IS
DELETED.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement