MT1095 QG.ai - admatec GmbH
Barcode Scan Engines
MT1095
This document was
provided by
admatec GmbH
admatec GmbH,
Wendenstrasse 29, 20097 Hamburg, Germany
Tel.: +49-40-238533-0, Fax: +49-40-238533-11
Internet: www.admatec.de , Email: info@admatec.de
Mini Barcode Reader
Quick Guide
Mini Barcode Reader Quick Guide
P/N: 8002-0027*00
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de las classe B prescrites dans le
Réglement sur le brouillage radioélectrique édicté par les ministère des Communications du Canada.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent
laboratory. The unit under test was found compliant with all the applicable Directives,
2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and
importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
-1-
RoHS
WARNING AND CAUTION
1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
If following condition occur, immediately power off the host computer,
disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose
under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature
changes.
3. Place the scanner in oily smoke or steam environment such as cooking
range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as
under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7. Use the scanner with anti-slip gloves containing plasticizer and
Do Not
chemicals or organic solvents such as benzene, thinner, insecticide etc
to clean the housing. Otherwise, it could not result fire and electrical
shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface
cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the
scanning window at other people’s eyes or eyesight may be damaged
by direct exposure under the light.
Do not put the scanner on an unstable or inclined plane.
The scanner may drop, creating injuries.
Once the interface cable is damaged such as exposed or broken copper
wires, stop using immediately and contact your dealer. Otherwise, it could
result fire or electrical shock.
-2-
OUT OF THE BOX
INTRODUCTION
Protective Cover
USB Connector
Scanner Tools
Trigger
Beeper
Mini Barcode Reader
CD
Mini Barcode Reader
Quick Guide
USB Extension Cable
(Optional)
Quick Guide
-3-
Exit Window
SPECIFICATIONS
Light source
Scan rate
Sensor
Resolution
PCS
Housing
Interface
Voltage
Current
625nm visible red LED
240 scans/sec
Linear CMOS sensor
5mil/ 0.127mm
30%
Plastic(Polycarbonate)
USB
5 VDC ± 5%
< 115 mA(Working); < 60 mA(Standby)
Operating Temp 0 to 50˚C (32˚F to 122˚F)
Storage Temp
-20 to 60˚C (-4˚F to 140˚F)
Symbologies All major 1D barcodes incl. GS1 Databar
-4-
GETTING STARTED
BEEPER INDICATION
Single long beep
Single beep
Single fast beep
Two beeps
Three fast beeps
Power up
Good read
The scanner reads a Code39 of
ASCII in configuration procedure
The scanner successfully reads
a configuration barcode
The scanner reads an unexpected
barcode during configuration
procedure. (scan [RESET] to abort
and start over)
EZU CONFIGURATION UTILITY




To scan a barcode, make sure the aiming beam crosses
every bar and space of the barcode. For fixed mounted
scanning, Continuous Mode(see READING MODE) is
recommanded.
-5-
1. Install EzU
2. Retrieve scanner
parameters
3. Edit the parameters
on the widow
4. Update scanner
parameters
EzU (available on CD and website) enables you to
configure the scanner with your PC/Laptop via USB
two-way communication. Please refer to EzU Help file
for detailed information.
-6-
GENERAL SETTINGS
READING MODE
. A001$
. F002$
DEFAULT
TRIGGER
. P023$
. F003$
RESET
TOGGLE
. A007$
. F001$
CHECK
VERSION
FLASH
INTERFACE
. F005$
CONTINUOUS
. C008$
USB HID
. F006$
CONTINUOUS
AUTO OFF
BEEPER
. F012$
BEEP OFF
-7-
-8-
KEYBOARD LAYOUT
. C010$
. C014$
ENGLISH
(USA)
ITALIAN
ENGLISH
(UK)
CZECH
(QWERTY)
FRENCH
CZECH
(QWERTZ)
. C018$
. C017$
. C022$
. C012$
. C021$
. C011$
GERMAN
HUNGARIAN
. C009$
. C016$
SWISS
JAPAN
(106 key)
. C013$
. C015$
SPANISH
-9-
ALT CODE
- 10 -
ENABLE SYMBOLOGIES
. G010$
. A002$
ENABLE
ALL CODE
CODE 93
. N017$
. K010$
CODE 32
IATA
. L014$
. L010$
UK PLESSEY
TELEPEN
. L001$
. N032$
MSI
GS1 DATABAR
. N010$
. N001$
INDUSTRIAL
2 OF 5
GS1 DATABAR
LIMITED
MATRIX
2 OF 5
GS1 DATABAR
EXPANDED
. N026$
. M010$
- 11 -
- 12 -
TERMINATOR
TEST BARCODES
. D012$
CR
. D011$
Code 39
CODE-39 TEST
LF
Interleaved 2 of 5
. D013$
CR + LF
9876543210
Code 128
. D010$
NONE
12345678
. D015$
SPACE
EAN
. D014$
TAB
- 13 -
- 14 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising