Link eight 10-/100-/1000-Mbps PoE+ devices to this tough, industrial

Link eight 10-/100-/1000-Mbps PoE+ devices to this tough, industrial
FCC and IC RFI Statements; Trademarks
Chapter 3: Operation
FEDERAL COMMUNICATIONS COMMISSION AND
INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used
properly, that is, in strict accordance with the manufacturer’s instructions, may cause inter­ference to radio
communication. It has been tested and found to comply with the limits for a Class A computing device in
accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable
protection against such interference when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which case the user at his own expense will
be required to take whatever measures may be necessary to correct the interference.
3. Operation
3.1 LED Indicators
3.2 Configuration and Setting Methods
No configuration and setting methods are needed.
3.3 Network Connector Pin Assignments
Table 3-2. RJ-45 connector pinout.
This digital apparatus does not exceed the Class A limits for radio noise emis­sion from digital apparatus set
out in the Radio Interference Regulation of Industry Canada.
Warranty and Return Information
If you determine that your LPH008A is malfunctioning, do not attempt to alter or
repair the unit. It contains no user-serviceable parts. Contact Black Box Technical
Support at 724-746-5500 or info@blackbox.com.
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete description,
including the nature and duration of the problem, when the problem occurs, and
any particular application that, when used, appears to create the problem or make
it worse.
Pin
MDI
(1000BASE-T)
1
TP1+
TX+
2
TP1-
TX-
3
TP2+
RX+
4
TP3+
—
5
TP3-
—
6
TP2-
RX-
7
TP4+
—
8
TP4-
—
8-Port Hardened Gigabit PoE+ Switch Quick Start Guide
Link eight 10-/100-/1000-Mbps PoE+ devices to
this tough, industrial-grade switch’s RJ-45
ports.
Delivers PoE+ power to remote powered devices, including IP
cameras, Wi-Fi access points, and VoIP phones.
Figure 3-2. RJ-45 straight-through and
crossover wiring diagrams.
RJ-45
connector
MDI
(10/100BASE-T)
LPH008A
RJ-45 8-pin straight-through wiring RJ-45 8-pin crossover wiring
Switch
PC (NIC)
Switch
Switch
3----------------------------- 33-----------------------------1
6----------------------------- 66-----------------------------2
1----------------------------- 11-----------------------------3
2----------------------------- 22-----------------------------6
4----------------------------- 44-----------------------------7
5----------------------------- 55-----------------------------8
7----------------------------- 77-----------------------------4
8----------------------------- 88-----------------------------5
LED indicators are located on the front panel of the switch. See Table 1-1.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par
Industrie Canada.
NOM Statement
Table 3-2. PoE pin definition.
Figure 3-1. RJ-45 connector.
© Copyright 2014. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond
logo are registered trademarks of BB Technologies, Inc. UL is a registered trademark of
Underwriters Laboratories. Any third-party trademarks appearing in this manual are acknowledged
to be the property of their respective owners.
LPH008A, version 1
Pin
10/100BASE-T(X) PSE RJ-45 port
Pin
1000BASE-T PSE RJ-45 port
1
TD+ with PoE power input +
1
BI_DA+ with PoE power input +
2
TD- with PoE power input +
2
BI_DA- with PoE power input +
3
RD+ with PoE power input -
3
BI_DB+ with PoE power input -
6
RD- with PoE power input -
4
BI_DC+
4
Not used
5
BI_DC-
5
Not used
6
BI_DB- with PoE power input
7
Not used
7
BI_DD+
8
Not used
8
BI_DDCustomer
Support
Information
FREE! Live, 24/7 Tech Support is just 60 seconds away.
724-746-5500 | blackbox.com
LPH008A
Chapter 1: Overview
724-746-5500 | blackbox.com
LPH008A
Chapter 1: Overview; Chapter 2: Hardware Installation
1. Overview
1.1 Introduction
Chapter 2: Hardware Installation
Chapter 3: Operation
2. Hardware Installation
1.3 Hardware Description
The Hardened Gigabit PoE+ Switch has eight 10/100/1000BASE-TX RJ-45
Ethernet ports and two Power LEDs. It supports Power over Ethernet, which
transmits electrical power, along with data, to remote devices over standard
twisted-pair cable in an Ethernet network. The switch uses a 5-pin terminal
block power connector.
724-746-5500 | blackbox.com
Figure 1-1 shows the Hardened Gigabit PoE+ Switch’s front panel. Table 1-1
describes its components.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) FREE technical support 24 hours a day, 7 days a
week: Call 724-746-5500 or fax 724-746-0746 Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Step 2: Connecting the Power
Refer to the illustration below to connect the power to the switch.
Step 1: Installing the Switch on a DIN Rail or Wall
Refer to the illustrations below to mount the switch on a DIN rail or wall.
NOTE: T he switch should be mounted on a well-grounded place, such as a
metal panel.
DIN rail
installation
Wallmount
installation
1.2 What’s Included
Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support at 724-746-5500 or info@blackbox.
com.
24–36 VDC
• (1) Hardened Gigabit PoE+ Switch
• (1) 5-pin terminal block for power input
• This user’s manual
24–36 VDC
Figure 1-1. Front panel.
Table 1-1. LPH008A components.
Optional accessories:
Step 3: Connecting the Network Devices
• Wallmount kit (45.4" [2.3 cm] thick)
Component
Description
(2) Power LEDs
Link to 10-/100-/1000-Mbps Ethernet devices
(1) Power Fault LED
Lights when power to the switch is on
• The corresponding RJ-45 LED will light if the Ethernet connection is linked
successfully.
(8) Link/Act. LEDs
Lights when the port is operating
• The LED will blink while the switch transfers data.
(8) Power Injected LEDs
Lights when the port is using PoE+
UL® Notice for Power Supply
(8) Gigabit LAN ports
Link to PoE+ devices
Use a power supply marked with “LPS,” “Limited Power Source,” or “Class 2” with
output rate 24–36 VDC (5 A maximum at 24 VDC).
• Connect your devices using standard UTP/STP cable with RJ-45 connectors to the
switch. (For the cable wiring diagrams, refer to the pin assignment in Figure 3-2.)
Figure 2-1. DIN rail or wallmount installation.
LPH008A
724-746-5500 | blackbox.com
Page 1
LPH008A
724-746-5500 | blackbox.com
Page 2
LPH008A
724-746-5500 | blackbox.com
Page 3
LPH008A
724-746-5500 | blackbox.com
Page 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising