Datasheet - STMicroelectronics
LEXX
Very low-dropout voltage regulator with inhibit function
Datasheet - production data
Description
The LEXX is a very low-dropout voltage regulator
available in SO-8, TO-92 packages and over a
wide range of output voltages.
The very low-dropout voltage (0.2 V) and low
quiescent current make it particularly suitable for
low-noise, low-power applications and in batterypowered systems.
Features









Very low-dropout voltage (0.2 V typ.)
Very low quiescent current (typ. 50 µA in
OFF mode, 0.5 mA in ON mode, no load)
Output current up to 100 mA
Output voltages: 3 V, 3.3 V, 4.5 V, 5 V, 8 V
Internal current and thermal limit
Small 2.2 µF capacitor for stability
Available in ±1% (A) or ±2% (C) selection at
25 °C
Supply voltage rejection: 80 dB (typ.)
Temperature range: -40 to 125 °C
This device is pin-to-pin compatible with the L78L
series. Furthermore, in the 8-pin configuration
(SO-8), it uses a shutdown logic control (pin 5,
TTL compatible). This means that when the
device is used as a local regulator, a part of the
board can be put in standby, decreasing the total
power consumption. In the three-terminal
configuration (TO-92), the device is always in
on-state. It requires a 2.2 µF capacitor for
stability, reducing the component size and cost.
Table 1: Device summary
Order code
Output voltage (V)
SO-8
TO-92 (Ammopack)
TO-92 (tape and reel)
LE30CD-TR
LE33CD-TR
3
LE33CZ-AP
LE33CZ-TR
LE45CD-TR
LE50ABD-TR
3.3
4.5
LE33ABZ-AP
5
LE50CD-TR
5
LE80CD-TR
8
May 2017
DocID2573 Rev 15
This is information on a product in full production.
1/24
www.st.com
Contents
LEXX
Contents
1
Diagram ............................................................................................ 3
2
Pin configuration ............................................................................. 4
3
Maximum ratings ............................................................................. 5
4
5
Electrical characteristics ................................................................ 6
Typical performance characteristics ........................................... 13
6
Package information ..................................................................... 16
7
2/24
6.1
SO-8 package information .............................................................. 16
6.2
SO-8 packing information ................................................................ 18
6.3
TO-92 packing information .............................................................. 19
6.4
TO-92 Ammopak packing information ............................................. 21
Revision history ............................................................................ 23
DocID2573 Rev 15
LEXX
1
Diagram
Diagram
Figure 1: Block diagram
DocID2573 Rev 15
3/24
Pin configuration
2
LEXX
Pin configuration
Figure 2: Pin connections (SO-8 top view, TO-92 bottom view)
4/24
DocID2573 Rev 15
LEXX
3
Maximum ratings
Maximum ratings
Table 2: Absolute maximum ratings
Symbol
Parameter
VI
DC input voltage
IO
Output current
Value
Unit
20
V
Internally limited (1)
PTOT
Power dissipation
Internally limited
TSTG
Storage temperature range
-65 to 150
°C
TOP
Operating junction temperature range
-40 to 125
°C
Notes:
(1)Our
SO-8 package, used for voltage regulators, is modified internally to have pins 2, 3, 6 and 7 electrically fused
to the die attach pad. This frame decreases the total thermal resistance of the package and increases its ability to
dissipate power when an appropriate area of copper on the printed circuit board is available for heatsinking. The
external dimensions are the same as SO-8 standard.
Table 3: Thermal data
Symbol
Parameter
SO-8
RthJC
Thermal resistance junction-case
20
RthJA
Thermal resistance junction-ambient
55
TO-92
Unit
°C/W
200
°C/W
Figure 3: Test circuit
If the INHIBIT pin is left floating, the regulator is in ON mode. However, when the
inhibit function is not used, it should be grounded to avoid any noise.
DocID2573 Rev 15
5/24
Electrical characteristics
4
LEXX
Electrical characteristics
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 4: LE30AB electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
2.970
3
3.030
Unit
IO = 10 mA
VI = 5 V
VO
Output voltage
V
IO = 10 mA
VI = 5 V
2.940
3.060
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
Vd
VIL
VIH
15
mV
3
15
mV
0.5
1
1.5
3
OFF mode
50
100
f = 120 Hz
81
f = 1 kHz
76
VI = 4 V
IO = 0.5 to 100 mA
Quiescent current
VI = 4 to 18 V
IO = 100 mA
VI = 6 V
eN
mA
3
IO = 0.5 mA
VI = 4 to 18 V
IO = 0 mA
SVR
V
VI = 3.7 to 18 V
∆VO
Id
18
Supply voltage rejection
Output noise voltage
Dropout voltage
IO = 5 mA
VI = 5 ± 1 V
ON mode
mA
f = 10 kHz
B = 10 Hz to 100 kHz
60
IO = 100 mA
0.2
µA
dB
50
µV
0.4
V
IO = 100 mA
TJ = -40 to 125 °C
0.5
Control input logic low
TJ = -40 to 125 °C
0.8
Control input logic high
TJ = -40 to 125 °C
2
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
6/24
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
LEXX
Electrical characteristics
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 5: LE30C electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
2.940
3
3.060
Unit
IO = 10 mA
VI = 5 V
VO
Output voltage
V
IO = 10 mA
VI = 5 V
2.880
3.120
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
IO = 0.5 to 100 mA
Quiescent current
VI = 4 to 18 V
IO = 100 mA
VI = 6 V
eN
Vd
mA
3
20
mV
3
25
mV
0.5
1
VI = 4 V
VI = 4 to 18 V
IO = 0 mA
SVR
V
VI = 3.7 to 18 V
∆VO
Id
18
Supply voltage rejection
Output noise voltage
Dropout voltage
IO = 5 mA
VI = 5 ± 1 V
ON mode
mA
1.5
3
OFF mode
50
100
f = 120 Hz
81
f = 1 kHz
76
f = 10 kHz
B = 10 Hz to 100 kHz
60
IO = 100 mA
0.2
dB
50
µV
0.4
V
IO = 100 mA
TJ = -40 to 125 °C
0.5
0.8
VIL
Control input logic low
TJ = -40 to 125 °C
VIH
Control input logic high
TJ = -40 to 125 °C
µA
2
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
7/24
Electrical characteristics
LEXX
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 6: LE33C electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
3.234
3.3
3.366
Unit
IO = 10 mA
VI = 5.3 V
VO
Output voltage
V
IO = 10 mA
VI = 5.3 V
3.168
3.432
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
IO = 0.5 to 100 mA
Quiescent current
VI = 4.3 to 18 V
IO = 100 mA
VI = 6 V
eN
Vd
mA
3
20
mV
3
25
mV
0.5
1
VI = 4.3 V
VI = 4.3 to 18 V
IO = 0 mA
SVR
V
VI = 4 to 18 V
∆VO
Id
18
Supply voltage rejection
Output noise voltage
Dropout voltage
IO = 5 mA
VI = 5.3 ± 1 V
ON mode
mA
1.5
3
OFF mode
50
100
f = 120 Hz
80
f = 1 kHz
75
f = 10 kHz
60
B = 10 Hz to 100 kHz
50
IO = 100 mA
0.2
dB
µV
0.4
IO = 100 mA
TJ = -40 to 125 °C
0.5
0.8
VIL
Control input logic low
TJ = -40 to 125 °C
VIH
Control input logic high
TJ = -40 to 125 °C
2
µA
V
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
8/24
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
LEXX
Electrical characteristics
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 7: LE45C electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
4.41
4.5
4.59
Unit
IO = 10 mA
VI = 6.5 V
VO
Output voltage
V
IO = 10 mA
VI = 6.5 V
4.32
4.68
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
mA
4
30
mV
3
25
mV
0.5
1
VI = 5.5 V
IO = 0.5 to 100 mA
VI = 5.5 to 18 V
IO = 0 mA
Quiescent current
VI = 5.5 to 18 V
IO = 100 mA
VI = 6 V
SVR
V
VI = 5.2 to 18 V
∆VO
Id
18
Supply voltage rejection
IO = 5 mA
VI = 6.5 ± 1 V
ON mode
mA
1.5
3
OFF mode
50
100
f = 120 Hz
77
f = 1 kHz
72
f = 10 kHz
60
B = 10 Hz to 100 kHz
50
IO = 100 mA
0.2
dB
eN
Output noise voltage
Vd
Dropout voltage
IO = 100 mA
TJ = -40 to 125 °C
0.5
VIL
Control input logic low
TJ = -40 to 125 °C
0.8
VIH
Control input logic high
TJ = -40 to 125 °C
2
µA
µV
0.4
V
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
9/24
Electrical characteristics
LEXX
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 8: LE50AB electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
4.95
5
5.05
Unit
IO = 10 mA
VI = 7 V
VO
Output voltage
V
IO = 10 mA
VI = 7 V
4.9
5.1
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
350
425
mA
4
20
mV
3
15
mV
0.5
1
VI = 6 V
IO = 0.5 to 100 mA
VI = 6 to 18 V
IO = 0 mA
Quiescent current
VI = 6 to 18 V
IO = 100 mA
VI = 6 V
SVR
V
VI = 5.7 to 18 V
∆VO
Id
18
Supply voltage rejection
IO = 5 mA
VI = 7 ± 1 V
ON mode
mA
1.5
3
OFF mode
50
100
f = 120 Hz
76
f = 1 kHz
71
f = 10 kHz
B = 10 Hz to 100 kHz
60
IO = 100 mA
0.2
dB
eN
Output noise voltage
50
Vd
Dropout voltage
IO = 100 mA
TJ = -40 to 125 °C
0.5
VIL
Control input logic low
TJ = -40 to 125 °C
0.8
VIH
Control input logic high
TJ = -40 to 125 °C
2
µA
µV
0.4
V
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
10/24
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
LEXX
Electrical characteristics
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 9: LE50C electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
4.9
5
5.1
Unit
IO = 10 mA
VI = 7 V
VO
Output voltage
V
IO = 10 mA
VI = 7 V
4.8
5.2
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
IO = 0.5 to 100 mA
Quiescent current
VI = 6 to 18 V
IO = 100 mA
VI = 6 V
eN
Vd
350
425
mA
4
30
mV
3
25
mV
0.5
1
VI = 6 V
VI = 6 to 18 V
IO = 0 mA
SVR
V
VI = 5.7 to 18 V
∆VO
Id
18
Supply voltage rejection
Output noise voltage
Dropout voltage
IO = 5 mA
VI = 7 ± 1 V
ON mode
mA
1.5
3
OFF mode
50
100
f = 120 Hz
76
f = 1 kHz
71
f = 10 kHz
B = 10 Hz to 100 kHz
60
IO = 100 mA
0.2
dB
50
µV
0.4
V
IO = 100 mA
TJ = -40 to 125 °C
0.5
0.8
VIL
Control input logic low
TJ = -40 to 125 °C
VIH
Control input logic high
TJ = -40 to 125 °C
µA
2
V
V
VI = 6 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
11/24
Electrical characteristics
LEXX
Refer to test circuits, TJ = 25 °C, CI = 0.1 µF, CO = 2.2 µF unless otherwise specified.
Table 10: LE80C electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
7.84
8
8.16
Unit
IO = 10 mA
VI = 10 V
VO
Output voltage
V
IO = 10 mA
VI = 10 V
7.68
8.32
TJ = -25 to 85 °C
VI
Operating input voltage
IO
Output current limit
IO = 100 mA
150
Line regulation
∆VO
Load regulation
IO = 0.5 mA
IO = 0.5 to 100 mA
Quiescent current
VI = 9 to 18 V
IO = 100 mA
VI = 9 V
eN
Vd
mA
5
35
mV
3
25
mV
0.7
1.6
VI = 9 V
VI = 9 to 18 V
IO = 0 mA
SVR
V
VI = 8.7 to 18 V
∆VO
Id
18
Supply voltage rejection
Output noise voltage
Dropout voltage
IO = 5 mA
VI = 10 ± 1 V
ON mode
mA
1.7
3.6
OFF mode
70
140
f = 120 Hz
72
f = 1 kHz
66
f = 10 kHz
57
B = 10 Hz to 100 kHz
50
IO = 100 mA
0.2
dB
µV
0.4
IO = 100 mA
TJ = -40 to 125 °C
0.5
0.8
VIL
Control input logic low
TJ = -40 to 125 °C
VIH
Control input logic high
TJ = -40 to 125 °C
2
µA
V
V
V
VI = 9 V
II
Control input current
VC = 6 V
10
µA
10
µF
ESR = 0.1 to 10 Ω
CO
12/24
Output bypass capacitance
IO = 0 to 100 mA
DocID2573 Rev 15
2
LEXX
5
Typical performance characteristics
Typical performance characteristics
Unless otherwise specified, VO(NOM) = 3.3 V.
Figure 4: Dropout voltage vs output current
Figure 5: Dropout voltage vs temperature
Figure 6: Shutdown current vs temperature
Figure 7: Supply current vs input voltage
DocID2573 Rev 15
13/24
Typical performance characteristics
LEXX
Figure 8: Short-circuit current vs dropout voltage
Figure 9: SVR vs frequency
Figure 10: Logic-controlled precision 3.3/5.0 V selectable output
14/24
DocID2573 Rev 15
LEXX
Typical performance characteristics
Figure 11: Sequential multi-output supply
Figure 12: Basic inhibit functions
DocID2573 Rev 15
15/24
Package information
6
LEXX
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK ®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
6.1
SO-8 package information
Figure 13: SO-8 package outline
16/24
DocID2573 Rev 15
LEXX
Package information
Table 11: SO-8 mechanical data
mm
Dim.
Min.
Typ.
A
Max.
1.75
A1
0.10
0.25
A2
1.25
b
0.31
0.51
b1
0.28
0.48
c
0.10
0.25
c1
0.10
0.23
D
4.80
4.90
5.00
E
5.80
6.00
6.20
E1
3.80
3.90
4.00
e
1.27
h
0.25
0.50
L
0.40
1.27
L1
1.04
L2
0.25
k
0°
ccc
8°
0.10
Figure 14: SO-8 recommended footprint (dimensions are in mm)
DocID2573 Rev 15
17/24
Package information
6.2
LEXX
SO-8 packing information
Figure 15: SO-8 tape and reel dimensions
Table 12: SO-8 tape and reel mechanical data
Dim.
mm
Min.
Typ.
A
330
C
12.8
D
20.2
N
60
T
18/24
Max.
13.2
-
22.4
Ao
8.1
Bo
5.5
5.9
Ko
2.1
2.3
Po
3.9
4.1
P
7.9
8.1
DocID2573 Rev 15
8.5
LEXX
6.3
Package information
TO-92 packing information
Figure 16: TO-92 tape and reel outline
DocID2573 Rev 15
19/24
Package information
LEXX
Table 13: TO-92 tape and reel mechanical data
mm
Dim.
Min.
Typ.
A1
4.80
T
3.80
T1
1.60
T2
2.30
d
0.45
0.47
0.48
P0
12.50
12.70
12.90
P2
5.65
6.35
7.05
F1, F2
2.40
2.50
2.94
F3
4.98
5.08
5.48
delta H
-2.00
W
17.50
18.00
19.00
W0
5.5
6.00
6.5
W1
8.50
9.00
9.25
2.00
W2
0.50
H
18.50
21
H3
0.5
1
2
H0
15.50
16.00
18.8
25.0
27.0
4.00
4.20
H1
D0
20/24
Max.
3.80
t
0.90
L
11.00
I1
3.00
delta P
-1.00
Ø1
352
355
358
Ø2
28
30
32
u
44
47
50
DocID2573 Rev 15
1.00
LEXX
6.4
Package information
TO-92 Ammopak packing information
Figure 17: TO-92 Ammopak tape and reel outline
DocID2573 Rev 15
21/24
Package information
LEXX
Table 14: TO-92 Ammopak tape and reel mechanical data
mm
Dim.
Min.
Typ.
A1
4.80
T
3.80
T1
1.60
T2
2.30
d
0.45
0.47
0.48
P0
12.50
12.70
12.90
P2
5.65
6.35
7.05
F1, F2
2.40
2.50
2.94
F3
4.98
5.08
5.48
delta H
-2.00
W
17.50
18.00
19.00
W0
5.5
6.00
6.5
W1
8.50
9.00
9.25
2.00
W2
0.50
H
18.50
21
H3
0.5
1
2
H0
15.50
16.00
18.8
25.0
27.0
4.00
4.20
H1
D0
22/24
Max.
3.80
t
0.90
L
11.00
I1
3.00
delta P
-1.00
DocID2573 Rev 15
1.00
LEXX
Revision history
7
Revision history
Table 15: Document revision history
Date
Revision
Changes
09-Jul-2004
6
IO typ. and max. are changed in tab. 24 and 25 - pag. 14.
16-Mar-2005
7
Add Tape & Reel for TO-92 - Note on Table 3.
12-Feb-2007
8
Change value TOP on Table 2.
26-Jul-2007
9
Add Table 1 in cover page.
29-Nov-2007
10
Modified: Table 25.
12-Feb-2008
11
Modified: Table 25.
10-Jul-2008
12
Modified: Table 1 and Table 25.
22-May-2012
13
Updated: Table 1 on page 1. Changed: TA in TJ test conditions from table
4 to table 10.
14-Mar-2014
14
Changed the part numbers LExxAB and LExxC to LEXX. Updated the
title. Added the ammopack package to the figure in cover page. Updated
the Table 1: Device summary. Updated the Description. Updated Figure
3. Changed the title of Figure 6. Updated mechanical data.
03-May-2017
15
Updated Table 1: "Device summary" and Section 6: "Package
information".
Minor text changes.
DocID2573 Rev 15
23/24
LEXX
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
24/24
DocID2573 Rev 15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising