Viscosity Kinematic Capillary - Stanhope-Seta

Viscosity Kinematic Capillary - Stanhope-Seta
Viscosity Kinematic Capillary
SETAVIS AUTOMATIC KINEMATIC VISCOMETER
83545-3
SETAVIS 'DOUBLE 6' KINEMATIC AUTO-VISCOMETER
ASTM D7279 Houillon Method
Correlates with: ASTM D445; D446; D2270; IP 71; IP 226; BS 188;
BS 2000 Part 71; BS 4459; EN 3104; ISO 2909; ISO 3104; FTM 791
305; NF T60-100; NF T60-136; JIS K2283
4
● Two independently controlled baths
● Up to 6 viscometer tubes per bath
● Micro samples
●Two tests per tube from a single sample
● Automatic tube cleaning and drying
● Control and data analysis software
The Setavis Double 6 KAV is a compact bench top, automatic kinematic
viscometer, equipped with two baths that each accept up to six kinematic
viscometer tubes. Applications include research, process, and batch
control. Suitable for testing both transparent and opaque samples over a
wide range of products, including lubricants, transformer oils, and used oils.
Rapid test times and high sample throughput are achieved by using
Setavis Auto Duplex tubes, which have two measurement zones,
doubling the number of results per test. The baths will also accept
manual Houillon type viscometer tubes.
Precision optical detectors eliminate timing errors due to operator
reaction time and parrallax errors. The fully automatic cleaning/drying
reduces the downtime between sample injections.
SUPPLIED WITH: Setavis KAV software, one 6 way Autoclean module,
tubing, connecting and mains leads and instruction manual.
Note: Supplied without viscometer tubes or thermometers, refer to the
accessories section. This equipment requires to be connected to a
computer, vacuum source and solvent containers.
83545-3 with additional 83575-2 and Viscometer Tubes (supplied separately)
●DUAL BATHS
The baths are independently temperature controlled within a range of
ambient to 150°C, allowing one bath to be set at 40° and the other at
100°C. Each bath comprises a heater coil, stirrer unit, and a cooling coil
for temperatures near ambient, ensuring even temperature distribution.
Up to six viscometer tubes can be installed in each bath.
BIO-FUEL TESTING
SOFTWARE INCLUDED
●FAST FLOW TIMES
CALIBRATION & VERIFICATION MATERIALS
Flow times are typically between 50 to 100 seconds. The sample flows
into the measuring section of the viscometer tube via a temperature
equilibrium zone.
SETAPLUS EXTENDED WARRANTY AVAILABLE
●HIGH SAMPLE THROUGHPUT
An average test, including cleaning, can be completed in less than 15
minutes, allowing a maximum of 24 samples per bath (48 separate test
results) per hour. With 12 positions fully utilised, typically 96 test results
can be achieved per hour.
T
SPECIFICATIONS
Viscosity Range:
2.5 to 2000 mm2/s
●ENCLOSED AUTOMATIC CLEANING
Temperature Range:
Ambient to 150°C
The Autoclean module can clean up to six viscometer tubes automatically.
After the sample is detected leaving the measuring section, the tube is
flushed with solvent and dried by air in preparation for the next sample.
Solvent usage is typically 10 to 20ml per test. The Autoclean module can be
connected to 2 alternative solvent supplies allowing samples with different
compositions to be tested in the same tube. The cleaning capacity can be
expanded to 12 way with an optional kit (83575-2).
Temperature Stability:
±0.01° below 100°C
±0.03° 100 to 150°C
Sample Size:
0.15 to 0.275 ml
Typical Flow Time:
50 to 100 seconds
No of Baths:
2
Bath Capacity:
2 litres
●MICRO SAMPLES
Tube Capacity:
up to 12 (6 per bath)
Voltage:
110/120V, 50/60Hz
220/240V, 50/60Hz (switchable)
Power:
800W
Size (HxWxD):
68 x 59 x 37cm
Weight:
40kg
The viscometer tubes only require a very small sample size (micro
samples), typically 0.25ml. The sample volume required is dependent on the
tube constant and is pre-determined at the time of tube manufacture. For
maximum accuracy and ease of handling, it is recommended that samples
are injected into the capillary using a positive displacement pipette.
32
TECHNICAL DATASHEETS AVAILABLE
+44 (0) 1932 564391 F
+44 (0) 1932 568363 E
sales@stanhope-seta.co.uk W
www.stanhope-seta.co.uk
Kinematic Capillary Viscosity
SETAVIS AUTOMATIC KINEMATIC VISCOMETER
●AUTO-DUPLEX VISCOMETER TUBES
ACCESSORIES - Setavis 'Double 6' Kinematic Auto-Vis.
Each tube has two measuring bulbs (upper and
lower) in series, providing two measurements
from a single sample injection. This increases
the overall capacity of the instrument to 24
simultaneous tests, and provides a quick check
of determinability. 7 tubes are available covering
the range 2.5 to 2000 mm2/s. Seta Auto Duplex
Viscometer Tubes are supplied fitted with optical
detectors suitable for transparent and opaque
samples, and are factory calibrated at 40°C in
accordance with ASTM D446 (calibration at 100°C
available on request).
REQUIRED
SETAVIS KAV AUTO DUPLEX TUBES.
Complete with auto-detection sensor head and leads. The range covers 2.5 to
2000mm2/s. Calibration is based on a minimum flow time of 50 seconds at 40°C.
Calibration Certificate (Works)
Seta Part No.
Nominal Constant
Sample Volume (ml)
0.05
0.1
0.3
0.5
1.0
3.0
5.0
0.15
0.175
0.175
0.225
0.250
0.250
0.275
83605-003
83605-004
83605-005
83605-006
83605-007
83605-008
83605-009
Viscosity Range
(mm2/s)
2.5 to 30
5 to 60
15 to 180
25 to 300
50 to 600
150 to 1200
250 to 2000
4
SETA KINEMATIC VISCOSITY BATH THERMOMETERS.
With ice point scale and 0.02°C subdivisions to allow easy reading to within 0.01°C.
Calibration Certificate (Works)
Calibration Certificate (UKAS) - optional
Seta Part No.
Works Certificate
83620-0
83622-0
83624-0
83626-0
●SETAVIS SOFTWARE
The Windows™ compatible Setavis KAV software
allows simultaneous tube management, data
logging and analysis of up to 12 Setavis AutoDuplex viscometer tubes. A real time display of
flow times is provided for left or right hand baths,
with kinematic viscosity calculated for both upper
and lower measuring bulbs. The percentage
mean difference of upper and lower values is also
displayed. An integral facility is provided for the
automatic calculation of Viscosity Index. Results
and sample numbers are stored and printed for
individual tubes. Each tube has a log of calibration
constants for both 40° and 100°C values. Cleaning
cycles are user programmable, allowing sample
extraction, cleaning, and drying times to be set for
each individual tube.
Seta Part No.
UKAS Certificate
83620-0Z
83622-0Z
83624-0Z
83626-0Z
Temperature
Set Point (°C)
40
50
100
150
Temperature
Range (°C)
38.6 to 41.4
48.6 to 51.4
98.6 to 101.4
148.6 to 151.4
83747-2
DIGITAL PIPETTE, 50 to 250µl, for transparent or opaque liquids.
83748-2
PIPETTE TIPS, disposable, pack of 200.
94630-0BATH OIL, 5 litres, for filling viscometer baths in the temperature range of
ambient to 80°C. 1 per bath.
AND/OR
94634-0BATH OIL, 5 litres, for filling viscometer baths in the temperature range of
80 to 120°C. 1 per bath.
AND/OR
94631-0SILICONE BATH OIL, 2 litres, for filling viscometer baths in the temperature
range of 100 to150°C, (3 required per bath).
OPTIONAL
83570-0SETA BACK-FLUSH KIT, for cleaning blocked tubes in situ. Comprises wash
bottle and tubing.
83575-26-WAY AUTOCLEAN FITTING KIT, extends the automatic cleaning function
to cover up to 12 tubes.
83582-2SETAVIS SOLVENT CONTAINER, (1 required for each solvent type).
83578-2WASTE EXTRACTION SYSTEM, two stage diaphragm vacuum pump and
2 waste containers. Suitable for cleaning up to 12 tubes mounted in two
baths.
83700-5SETA UNIVERSAL PRE-HEATING AND FILTERING KIT, for use with
transparent and opaque samples. Comprises hot plate, support, high
temperature 75 micron reusable filter unit and 100 low temperature
disposable sample containers with 100 associated 75 micron filters and
covers.
99300-2MINI LOW TEMPERATURE BATH/CIRCULATOR, to provide chilled water if
local supply exceeds 18°C, (for details see page 139).
45002-0
SETAPLUS EXTENDED 12 MONTH WARRANTY
CALIBRATION, VERIFICATION & TRAINING
ISCOSITY STANDARDS (for details see page 48).
V
99928-0SETATHERM, precision logging digital thermometer optimised for
verification of viscosity baths, (for details see page 129).
Note: Other items which may be required include: Solvents for tube cleaning.
CONSUMABLES - Setavis 'Double 6' Kinematic Auto-Vis.
2 Years/2000 Tests
Qty
22420-005 ‘O’ RING PIPE SEAL. pack of 10�����������������������������������������������������������������������������2
T
+44 (0) 1932 564391 F
+44 (0) 1932 568363 E
sales@stanhope-seta.co.uk W
www.stanhope-seta.co.uk
33
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising