MP723 Digital Projector User Manual

MP723 Digital Projector User Manual
MP723 Digital Projector
User Manual
Welcome
http://www.pureglare.com.au
Table of contents
Important safety
instructions .........................3
Introduction........................7
Projector features .................................. 7
Shipping contents.................................. 8
Projector exterior view .......................... 9
Controls and functions ....................... 10
Positioning your
projector............................14
Choosing a location............................. 14
Obtaining a preferred projected image
size ........................................................ 15
Connection .......................18
Connecting a computer or monitor... 18
Connecting Video source devices....... 21
Operation ..........................26
Starting up the projector..................... 26
Using the menus.................................. 27
Securing the projector ......................... 28
Switching input signal ......................... 31
Adjusting the projected image ............ 32
Magnifying and searching for details on
the projected picture ........................... 33
Selecting the aspect ratio..................... 34
Optimizing the image.......................... 35
Setting the presentation timer ............ 39
Remote paging operations .................. 40
Hiding the image ................................. 41
Freezing the image............................... 41
Utilizing FAQ function ....................... 42
Locking control keys ........................... 42
2
Operating in a high altitude
environment .........................................43
Creating your own startup screen .......43
Adjusting the sound.............................44
Personalizing the projector menu
display ...................................................44
Shutting down the projector ...............45
Menu operation ...................................46
Maintenance......................53
Care of the projector............................53
Lamp information................................54
Troubleshooting ...............60
Specifications ....................61
Projector specifications........................61
Dimensions...........................................62
Timing chart.........................................63
Warranty and Copyright
information .......................65
Regulation statements ......66
Table of contents
http://www.pureglare.com.au
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before you
operate your projector. Save it for
future reference.
2.
Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
3.
Refer servicing to qualified service
personnel.
4.
Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5.
In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of ±10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
6.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
Important safety instructions
http://www.pureglare.com.au
3
Safety Instructions (Continued)
7.
4
The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
8.
Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9.
Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
10.
Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11.
Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
12.
When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
Important safety instructions
http://www.pureglare.com.au
Safety Instructions (Continued)
13.
Do not place this projector in any of the 14. Do not block the ventilation holes.
- Do not place this projector on a blanket,
following environments.
bedding or any other soft surface.
- Do not cover this projector with a cloth or
any other item.
- Do not place inflammables near the
projector.
- Space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
15.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
16.
3000 m
(10000 feet)
Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
0m
(0 feet)
Important safety instructions
http://www.pureglare.com.au
5
Safety Instructions (Continued)
17.
Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
18.
Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
19.
This product is capable of displaying
inverted images for ceiling mount
installation.
Ceiling mounting the projector
We want you to have a pleasant
experience using your BenQ projector,
so we need to bring this safety matter to
your attention to prevent possible
damage to person and property.
If you intend to mount your projector
on the ceiling, we strongly recommend
that you use a proper fitting BenQ
projector ceiling mount kit and that
you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector
ceiling mount kit, there is a safety risk
that the projector may fall from the
ceiling due to an improper attachment
through the use of the wrong gauge or
length screws.
You can purchase a BenQ projector
ceiling mount kit from the place you
purchased your BenQ projector. BenQ
recommends that you also purchase a
separate Kensington lock compatible
security cable and attach it securely to
both the Kensington lock slot on the
projector and the base of the ceiling
mount bracket. This will perform the
secondary role of restraining the
projector should its attachment to the
mounting bracket become loose.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
6
Important safety instructions
http://www.pureglare.com.au
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
Wall color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
•
•
Selectable password protected function
Up to 11 sets of picture modes providing multiple choices for different projection
purposes
3D color management allowing color adjustments to your liking
Detachable keypad on the projector to prevent stealing
Splash Screen lock to prevent unauthorized use
Selectable quick cooling function makes the projector cool in a shorter time
FAQ to troubleshoot operational problems with one quick button press
Presentation timer for a better control of time during presentations
High quality manual zoom lens
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and Economic modes to reduce the power consumption
Built-in speaker provides mixed mono audio when an audio input is connected
Powerful AV function to provide high quality video image
Component HDTV compatibility (YPbPr)
HDCP compatibility
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input source contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
http://www.pureglare.com.au
7
Shipping contents
The projector is shipped with the cables required for connection to a PC or video
equipment. Carefully unpack and verify that you have all of the items shown below. If any of
these items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
*The warranty card and safety manual are only supplied in some specific regions. Please
consult your dealer for detailed information.
PU
SH
Projector
Soft carry case
Quick start guide User manual CD
(UK)
(US)
(EU)
(AU)
Soft cover
(KOREA)
Remote control
with batteries
Warranty card*
Safety manual*
(CHINA)
(3-2
power
adaptor)
Power cord
VGA cable
Optional accessories
1.
2.
8
Spare lamp kit
Ceiling mount kit
3.
4.
Presentation Plus
RS232 cable
Introduction
http://www.pureglare.com.au
Projector exterior view
Front/upper side
5
1
1.
2.
3.
4.
5.
6
6.
7.
7
8.
8 9.
9 10.
11.
2
3
4
PU
SH
12.
13.
14.
15.
16.
17.
18.
Rear/lower side
14 15 16
17
18
19
20 21 22
23
10
11
19.
20.
21.
12
13
4
24
22.
23.
24.
Lamp cover
Vent (heated air exhaust)
Lens sliding door
Quick-release button
External control panel
(See "Projector" on page 10
for details.)
Focus ring and Zoom ring
Vent (cool air intake)
Front IR remote sensor
Projection lens
AC power cord inlet
Kensington anti-theft lock
slot
Rear adjuster foot
Ceiling mounting holes
Rear IR remote sensor
Video input socket
S-Video input socket
RGB signal output socket
RGB (PC)/Component
video (YPbPr/ YCbCr)
signal input socket
DVI input socket
Audio socket
12VDC output terminal
Used to trigger external
devices such as an electric
screen or light control, etc.
Consult your dealer for how
to connect these devices.
USB socket
RS232 control port
Speaker grill
Introduction
http://www.pureglare.com.au
9
Controls and functions
Projector
7.
1
2
8.
9
3
4
9.
5
10
6
11
7
12
13
8
10.
14
10
1.
2.
3.
4.
5.
6.
10
Focus ring
Adjusts the focus of the projected image.
See "Fine-tuning the image size and clarity" 11.
on page 32 for details.
Zoom ring
Adjusts the size of the image. See "Finetuning the image size and clarity" on page 12.
32 for details.
TEMPerature warning light
Lights up red if the projector's temperature
becomes too high. See "Indicators" on page
59 for details.
POWER indicator light
Lights up or flashes when the projector is
under operation. See "Indicators" on page
59 for details.
13.
I
I
Power
Toggles the projector on or off.
See "Starting up the projector" on page 26
14.
and "Shutting down the projector" on page
45 for details.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings. See "Using
the menus" on page 27 for details.
Left/
Starts the FAQ function. See "Utilizing FAQ
function" on page 42 for details.
BLANK
Used to hide the screen image. See "Hiding
the image" on page 41 for details.
LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem. See "Indicators" on page 59 for
details.
Keystone/Arrow buttons ( / Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection. See
"Correcting keystone" on page 33 for
details.
AUTO
Automatically determines the best picture
timings for the displayed image. See "Autoadjusting the image" on page 32 for details.
Right/
Activates panel key lock. See "Panel Key
Lock" on page 50 for details.
When the On-Screen Display (OSD) menu
is activated, the #7, #10, and #12 buttons
are used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 27 for details.
SOURCE
Displays the source selection bar. See
"Switching input signal" on page 31 for
details.
Mode/enter
Selects an available picture setup mode. See
"Selecting a picture mode" on page 35 for
details.
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 27 for details.
Introduction
http://www.pureglare.com.au
Remote control
13
1
14
2
15
3
16
4.
4
5
17
6
18
7
19
8
4
9
20
5.
6.
21
7.
10
22
11
12
8.
9.
1.
2.
3.
I
I Power
10.
Toggles the projector on or off.
See "Starting up the projector" on page 26
and "Shutting down the projector" on page 11.
45 for details.
ASPECT
12.
Selects the display aspect ratio. See
"Selecting the aspect ratio" on page 34 for
details.
CAPTURE
Captures the projected picture and save it
as your startup screen. See "Creating your
own startup screen" on page 43 for details.
Keystone/Arrow buttons ( / Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection. See
"Correcting keystone" on page 33 for
details.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings. See "Using
the menus" on page 27 for details.
Left/
Starts the FAQ function. See "Utilizing
FAQ function" on page 42 for details.
BLANK
Used to hide the screen image. See "Hiding
the image" on page 41 for details.
ENTER
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 27 for details.
TIMER ON/SHOW
Activates or displays an on-screen timer
based on your own timer setting. See
"Setting the presentation timer" on page 39
for details.
BRIGHTNESS
Adjusts brightness. See "Adjusting
Brightness" on page 36 for details.
CONTRAST
Adjusts contrast. See "Adjusting Contrast"
on page 36 for details.
TIMER SETUP
Enters presentation timer setting directly.
See "Setting the presentation timer" on
page 39 for details.
Introduction
http://www.pureglare.com.au
11
13.
14.
15.
16.
17.
18.
19.
20.
21.
12
Indicator light
Flashes or lights red when any key on the
remote control is pressed.
MODE
Depending upon which input signal is
selected, selects an available picture mode.
See "Selecting a picture mode" on page 35
for details.
FREEZE
Freezes the projected image. See "Freezing
the image" on page 41 for details.
MUTE
Toggles projector audio between on and
off.
AUTO
Automatically determines the best picture
timings for the displayed image. See "Autoadjusting the image" on page 32 for details.
22.
D. ZOOM (+, -)
Magnifies or reduces the projected image
size. See "Magnifying and searching for
details on the projected picture" on page 33
for details.
Operating the LASER pointer
The LASER Pointer is a
presentation aid for
professionals. It emits red
colored light when you press it
and the indicator lights up red.
The laser beam is visible. It is
necessary to press and hold
LASER for continuous output.
Do not look into the laser light window or
shine the laser light beam on yourself or
others. See the warning messages on the
back of the remote control and the enclosed
''User Information'' prior to using it.
Right/
The laser pointer is not a toy. Parents should be
Locks the buttons on the projector. See
mindful of the dangers of laser energy and keep
"Locking control keys" on page 42 for
this remote control out of the reach of children.
details.
When the On-Screen Display (OSD) menu
is activated, the #4, #6 and #18 buttons are
used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 27 for details.
SOURCE
Displays the source selection bar. See
"Switching input signal" on page 31 for
details.
LASER
Emits visible laser pointer light for
presentation purposes. See "Operating the
LASER pointer" on the right for details.
PAGE /
Operate your display software program (on
a connected PC) which responds to page
up/down commands (like Microsoft
PowerPoint). See "Remote paging
operations" on page 40 for details.
Introduction
http://www.pureglare.com.au
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
• Operating the projector from the
• Operating the projector from the
rear
front
Ap
pro
x.
15°
PU
p
Ap
SH
rox
.1
5°
Replacing the remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it up in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position. Stop
when it clicks into place.
Avoid leaving the remote control and batteries in an excessive heat or humid environment like
the kitchen, bathroom, sauna, sunroom or in a closed car.
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended period of
time, remove the batteries to avoid damage to the remote control from possible battery
leakage.
Introduction
http://www.pureglare.com.au
13
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit
from your dealer to mount your projector on the
ceiling.
Set Front Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
3.
Rear Table
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
4.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mounting Kit are required for
this installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector on.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
14
Positioning your projector
http://www.pureglare.com.au
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
4:3 is the native aspect ratio of this projector. To be able to project a complete 16:9
(widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the
projector's native aspect width. This will result in a proportionally smaller height equivalent
to 75% of the projector's native aspect height.
4:3 aspect image in a 4:3 aspect display area
16:9 aspect image scaled to a 4:3 aspect
display area
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed
by this projector. This will be seen as darkened (unlit) bars along the top and bottom
(vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a
scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.
When determining the position of your projector, you should consider its intended use and
input signal aspect ratios. All inputs (other than composite Video being fed a 16:9 aspect
signal) will display in a 4:3 aspect ratio (and will require an additional 33% display height
than that of the scaled 16:9 aspect image projection area).
IMPORTANT: Do not select a permanent projector position based upon a 16:9 projection if you
will ever need to select an input (other than composite Video being fed a 16:9 aspect signal).
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
You can see from the diagram on page 17, that this type of projection causes the bottom edge
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. There are two dimensions to consider, the perpendicular
horizontal distance from the center of the screen (projection distance), and the vertical
offset height of the projector from the horizontal edge of the screen (offset).
Positioning your projector
http://www.pureglare.com.au
15
How to determine the position of the projector for a given
screen size
1.
2.
Select your screen size.
Refer to the table and find the closest match to your screen size in the left columns
labelled "4:3 screen diagonal". Using this value, look across this row to the right to find
the corresponding average distance from screen value in the column labelled
"Average". This is the projection distance.
3.
On that same row, look across to the right column and make note of the Vertical offset
value. This will determine the final vertical offset placement of the projector in
relation to the edge of the screen.
4.
The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using a 120 inch screen, the average projection distance is 4667 mm
and with a vertical offset of 183 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 33 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1.
Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
2.
Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled "Average". Check that your measured distance is
between the min and max distances listed on either side of the average distance value.
3.
Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
4.
On that same row, look across to the right column and make note of the Vertical offset
value. This will determine the final placement of the screen in relation to the
horizontal plane of the projector.
For example, if your measured projection distance was 4.5m (4500mm), the closest match in
the Average column is 4593 mm. Looking across this row shows that a 3000 mm (3.0 m)
screen is required. If you can only obtain imperial sized screens, the listed screen sizes on
either side of the 3.0 m screen are the 9' and 10' screens.
Checking the min and max projection distance values for these screen sizes, indicates that
the 4.5 m measured projection distance will fit the 10' size screen. The projector can be
adjusted (using the zoom control) to display on these different screen sizes at those
projection distances. Be aware that these different screens have different vertical offset
values.
16
Positioning your projector
http://www.pureglare.com.au
Maximum zoom
Minimum zoom
Screen
Center of lens
Offset
Projection distance
4:3 screen diagonal
Feet Inches
mm
4
48
5
6
60
72
7
8
84
96
9
108
10
120
12
144
15
180
18
216
25
300
1219
1500
1524
1829
2000
2134
2438
2500
2743
3000
3048
3500
3658
4000
4572
5000
5486
6000
7620
Distance from Screen in mm
Min length
Average
Max length
(with max.
(with min.
zoom)
zoom)
1778
2187
2222
2667
2916
3111
3556
3645
4000
4374
4444
5104
5333
5833
6667
7291
8000
8749
11111
1867
2297
2333
2800
3062
3267
3733
3828
4200
4593
4667
5359
5600
6124
7000
7655
8400
9186
11667
1956
2406
2444
2933
3208
3422
3911
4010
4400
4812
4889
5614
5867
6416
7333
8020
8800
9624
12222
Vertical offset in mm
73
90
91
110
120
128
146
150
165
180
183
210
219
240
274
300
329
360
457
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
Positioning your projector
http://www.pureglare.com.au
17
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 8). They are commercially available from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA and DVI input sockets that allow you to connect it to both
IBM® compatibles and Macintosh® computers. A Mac adapter (an optional accessory) is
needed if you are connecting legacy version Macintosh computers.
Additionally, you can also connect the projector to a computer via the USB cable so you can
perform paging operations of the application on the PC or notebook.
To connect the projector to a notebook or desktop computer (either through a
VGA cable or VGA to DVI-A cable):
•
With a VGA cable:
•
With a VGA to DVI-A cable:
1.
Take the supplied VGA cable and
connect one end to the D-Sub
output socket of the computer.
Connect the other end of the VGA
cable to the D-SUB/COMP. IN
signal input socket on the projector.
1.
Take a VGA to DVI-A cable and
connect the VGA end to the D-Sub
output socket of the computer.
Connect the DVI end of the VGA to
DVI-A cable to the DVI signal input
socket on the projector.
2.
3.
4.
18
2.
If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and the smaller end to the USB socket
on the projector. See "Remote paging operations" on page 40 for details.
If you wish to make use of the projector (mixed mono) speaker in your
presentations, take a suitable audio cable and connect one end of the cable to the
audio output socket of the computer, and the other end to the AUDIO socket of
the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Settings" on page 51 for details.
Connection
http://www.pureglare.com.au
The final connection path should be like that shown in the following diagram:
notebook or
desktop computer
i. VGA cable
ii. VGA to DVI-A cable
iii. Audio cable
i or ii
iii
iv
iv. USB cable
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connection
http://www.pureglare.com.au
19
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the D-SUB OUT signal output socket on the projector to an external monitor
with a VGA or VGA to DVI-A cable by following the instructions below.
To connect the projector to a monitor (either through a VGA cable or VGA to
DVI-A cable):
•
With a VGA cable:
•
With a VGA to DVI-A cable:
Note: Your monitor must be equipped with
a DVI input socket.
1.
Connect the projector to a computer as described in "Connecting a computer" on
page 18.
The D-SUB output only works when an appropriate D-SUB input is made to the
projector. Be sure the projector is connecting with the computer using the D-SUB/
COMP. IN socket, not the DVI socket.
2.
Take a suitable VGA cable (only one
supplied) and connect one end of
the cable to the D-Sub input socket
of the video monitor.
Connect the other end of the cable
to the D-SUB OUT socket on the
projector.
3.
2.
3.
Take a VGA to DVI-A cable and
connect the DVI end of the cable to
the DVI input socket of the video
monitor.
Connect the VGA end of the cable to
the D-SUB OUT socket on the
projector.
The final connection path should be like that shown in the following diagram:
notebook or desktop
computer
(DVI)
i. VGA to DVI-A cable
i
ii
iii
ii. VGA cable
iii. VGA cable
20
(VGA)
Connection
http://www.pureglare.com.au
Connecting Video source devices
This section describes how to connect the projector to Video source devices using video
cables. Video cable connections are recommended for Video presentations.
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• DVI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is DVI. If your source device is equipped with a
DVI socket, based on the type of DVI connector you have, you can enjoy digital or high-end
analog video quality.
See "Connecting a DVI source device" on page 22 for how to connect the projector to a DVI
source device and other details.
If no DVI source is available, the next best video signal is Component Video (not to be
confused with composite Video). Digital TV tuners and DVD players output Component
Video natively, so if available on your devices, they should be your connection method of
choice in preference to S-Video or (composite) Video.
See "Connecting a Component Video source device" on page 23 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 24 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 25 for how to connect the
projector to a composite Video device.
Connecting Audio
The projector has a built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theatre or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
Connection
http://www.pureglare.com.au
21
Connecting a DVI source device
The projector provides a DVI input socket that allows you to connect it to a DVI source
device like a DVD player, or a VGA output device like a notebook or desktop computer.
There are three types of DVI connectors: DVI-A, DVI-D, and DVI-I. The DVI-I socket is an
integrated connector which supports both formats: DVI-A, and DVI-D.
DVI-A format is used to carry a DVI signal to an analog (VGA) display, or vice-versa.
Although some signal quality is lost from the signal conversion, it still transmits higher
picture quality than a standard VGA connection.
DVI-D format is used to directly carry a digital signal to a digital display without signal
conversion. The pure digital connection provides faster and higher image quality than an
analog connection, due to the nature of the digital format.
DVI-A and DVI-D formats are non-interchangeable. You cannot connect a DVI-A format
connector to DVI-D equipment and visa-versa. Make sure you know which kind of format
your equipment is fitted with before you purchase any cables. Or you can purchase a DVI-I
cable which will be more useful in any type of DVI connection situation.
Examine your source device to determine if it has an unused DVI output socket available:
•
If so, you can continue with this procedure.
•
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a DVI source device or a computer:
For information on connecting a DVI source device to a computer through a VGA to DVI-A
cable, see "Connecting a computer" on page 18.
1.
2.
3.
Take a DVI (DVI-D or DVI-I) cable and connect one end to the DVI output socket of
the DVI source device.
Connect the other end of the cable to the DVI signal input socket on the projector.
If you wish to make use the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output sockets of the video device,
and the other end to the AUDIO socket of the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Settings" on page 51 for
details.
AV device
DVI-D or
DVI-I cable
22
Connection
http://www.pureglare.com.au
Audio
cable
In the unlikely event that you connect the projector to a DVD player via the projector’s DVI-D
input and the projected picture displays wrong colors, please change the color space to YUV.
See "Changing Color Space" on page 31 for details.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue; and red to red.
2.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with
a D-Sub type connector) to the D-SUB/COMP. IN socket on the projector.
3.
If you wish to make use of the projector (mixed mono) speaker, take a suitable audio
cable and connect one end of the cable to the audio output socket of the computer,
and the other end to the Audio socket of the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Settings" on page 51 for details.
The final connection path should be like that shown in the following diagram:
A/V device
Component Video to
VGA (D-Sub) adaptor
cable
Audio cable
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting Audio" on page 21 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
Connection
http://www.pureglare.com.au
23
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
A/V device
S-Video cable
24
Audio cable
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting Audio" on page 21 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 21 for details.
Connection
http://www.pureglare.com.au
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2.
Connect the other end of the Video cable to the VIDEO socket on the projector.
The final connection path should be like that shown in the following diagram:
A/V device
Audio cable
Video cable
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting Audio" on page 21 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 21 for details.
Connection
http://www.pureglare.com.au
25
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch (where
fitted). Check that the Power indicator on the
projector lights orange after power has been
applied.
2.
Slide the lens cover open. If it is closed, it could
become deformed due to the heat produced by
the projection lamp.
PU
SH
3.
Press II Power on the projector or remote
control to start the projector. As soon as the lamp
lights up, a "Power On Tone" will be heard. The
Power indicator light flashes green and stays
green when the projector is on.
The start up procedure takes about 30 seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
To turn of the ring tone, see "Turning off the
Power on/off ring tone" on page 44 for details.
If the projector is still hot from previous activity, it will
run the cooling fan for approximately 90 seconds before
energizing the lamp.
4.
5.
6.
If you are prompted for a password, press the arrow buttons to enter a six digit
password. See "Utilizing the password function" on page 28 for details.
Switch all of the connected equipment on.
The projector will start to search for input signals. The current input source being
scanned displays in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the 'No Signal' message will continue displaying until an input source
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 31 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 63 for details.
26
Operation
http://www.pureglare.com.au
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
Main menu
DISPLAY
Off
Wall Color
Auto
Aspect Ratio
Highlight
Sub-menu
Keystone
Position
Status
ENTER
Phase
0
H. Size
0
Press MENU/
EXIT to the
previous
page or to
exit.
Digital Zoom
Current input signal
Analog RGB
MENU
Exit
To use the OSD menus, please set the OSD menu to your familiar language first.
1.
Press MENU/EXIT on the projector or
remote control to turn the OSD menu on.
3.
Press
to highlight Language
and press / to select a
preferred language.
DISPLAY
Wall Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Digital Zoom
Analog RGB
Off
Auto
SYSTEM SETUP: Basic
Presentation Timer
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Timer Controller
Splash Screen
My Screen
0
0
MENU Exit
Analog RGB
2.
Use / to highlight the SYSTEM
SETUP: Basic menu.
4.
SYSTEM SETUP: Basic
Presentation Timer
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Timer Controller
Splash Screen
My Screen
Analog RGB
English
Front Table
Disable
Disable
Off
Disable
BenQ
English
Front Table
Disable
Disable
Off
Disable
BenQ
MENU Exit
Press MENU/EXIT twice* on
the projector or remote control
to leave and save the settings.
*The first press leads you back to
the main menu and the second
press closes the OSD menu.
MENU Exit
Operation
http://www.pureglare.com.au
27
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent stealing. If not, purchase a lock,
like Kensington lock, to secure the projector. You can locate a Kensington lock slot on the
rear side of the projector. See item 11 on page 9 for details.
A Kensington security cable lock is usually the combination of key(s) and lock. Refer to the
lock’s documentation about how to use it.
Removing the control keypad on the projector
The control key pad on the projector is detachable.
Once the key pad is removed from the projector, it
is not possible to operate the projector without the
control keypad or remote control. We would
suggest that you keep the control key pad and
remote control away from the projector in case they
are taken together with the projector.
To remove the control keypad:
1.
Locate the screw locations on the lower
corner of the control keypad.
2.
Completely loosen the screws.
3.
Lift the control key pad by pulling the screws.
4.
Remove the control key pad from the
projector.
5.
After removing the control keypad from the
projector, you can use the soft cover supplied
to cover the keypad socket if necessary.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu.
WARNING: You will be inconvenienced if you activate the password functionality and
subsequently forget the password. Print out this manual (if necessary) and write the password
you used in this manual, and keep the manual in a safe place for later recall.
28
Operation
http://www.pureglare.com.au
Setting a password
Once a password has been set and the power on lock is activated, the projector cannot be
used unless the correct password is entered every time the projector is started.
Once a password has been set and the splash screen lock is activated, you cannot change the
splash screen that displays at projector startup unless the correct password is entered.
1.
2.
3.
4.
5.
6.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings
menu. Press Mode/enter on the projector or ENTER on the remote control. The
Security Settings page displays.
Highlight Change Security Settings and press Mode/enter on the projector or ENTER
on the remote control.
As pictured to the right, the four arrow buttons
INPUT NEW PASSWORD
Power On Lock and Splash Screen Lock
( , , , ) respectively represent 4 digits (1,
use the same password
2, 3, 4). According to the password you desire to
set, press the arrow buttons to enter six digits for
the password.
Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns
MENU Back
to the Security Settings page.
To activate the Power On Lock function, press / to highlight Power On Lock and
press /
to select On.
To activate the Splash Screen Lock function, press / to highlight Splash Screen
Lock and press /
to select On.
When the Splash Screen Lock is activated, the My Screen function in the SYSTEM
SETUP: Basic menu will be password-protected.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
7.
To leave the OSD menu, press MENU/EXIT.
If you forget the password
If the password function is activated, you will be asked
to enter the six digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right displays
lasting for three seconds, and the INPUT PASSWORD
message follows. You can retry by entering another sixdigit password, or if you did not record the password in
this manual, and you absolutely do not remember it,
you can use the password recall procedure. See
"Entering the password recall procedure" on page 30 for
details.
Password Error
Please try again.
If you enter an incorrect password 5 times in
succession, the projector will automatically shut down
in a short time.
Operation
http://www.pureglare.com.au
29
Entering the password recall procedure
Press and hold AUTO on the projector or remote
control for 3 seconds. The projector will display a
coded number on the screen. Write down the
number and turn off your projector. Seek help
from the local BenQ service center to decode the
number. You may be required to provide proof of
purchase documentation to verify that you are an
authorized user of the projector.
RECALL PASSWORD
Please write down the recall code,
and contact BenQ
Customer Center.
Recall Code:
0212
MENU
Exit
Changing the password
1.
2.
3.
4.
Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings >
Change Password menu.
Press Mode/enter on the projector or ENTER on the remote control. The message
'INPUT CURRENT PASSWORD' displays.
Enter the old password.
i. If the password is correct, another message 'INPUT NEW PASSWORD' displays.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT CURRENT PASSWORD' displays for your
retry. You can press MENU/EXIT to cancel the change or try another password.
Enter a new password.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5.
6.
7.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to
the projector. Remember to enter the new
Password Changed
password next time the projector is started.
To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Change Security Settings menu after opening the OSD menu system. Press Mode/
enter. The message 'INPUT PASSWORD' displays. Enter the current password.
i. If the password is correct, the OSD menu returns to the Security Settings page.
Press to highlight Power On Lock and press /
to select Off. You will not
have to enter the password next time when turning on the projector.
Press to highlight Splash Screen Lock and press /
to select Off. The Splash
Screen function in the SYSTEM SETUP: Basic menu will be available for your
change.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT PASSWORD' displays for your retry. You can
press MENU/EXIT to cancel the change or try another password.
30
Operation
http://www.pureglare.com.au
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time. When starting up, the projector automatically search for the
available signals.
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of
this projector) if you want the projector to automatically search for the signals.
You can also manually cycle through the available
input sources.
1.
2.
•
Press SOURCE on the projector or remote
control. A source selection bar displays.
Press / until your desired signal is selected
and press Mode/enter on the projector or
ENTER on the remote control.
Once detected, the selected source information
will display at the corner of the screen for
seconds. If there is multiple equipment
connected to the projector, repeat steps 1-2 to
search for another signal.
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly
moving images (movies).
D-Sub/Comp.
DVI-A
DVI-D
Video
S-Video
The input signal type effects the options available
for the Picture Mode. See "Selecting a picture
mode" on page 35 for details.
•
The native display resolution of this projector is in
a 4:3 aspect ratio. For best display picture results,
you should select and use an input source which
outputs at this resolution. Any other resolutions
will be scaled by the projector depending upon the
'aspect ratio' setting, which may cause some
image distortion or loss of picture clarity. See
"Selecting the aspect ratio" on page 34 for details.
Changing Color Space
In the unlikely event that you connect the projector to a DVD player via the projector’s DVID input and the projected picture displays wrong colors, please change the color space to
YUV.
To do this:
1.
2.
Press MENU/EXIT and then press / until the SOURCE menu is highlighted.
Press to highlight Color Space Conversion and press / to select YUV.
This function is only available when the DVI-D input socket is in use.
Operation
http://www.pureglare.com.au
31
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the front
of the projector. Once the image is positioned
where you want it, release the quick-release
button to lock the foot in position.
2.
Screw the rear adjuster foot to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower
the projector. Screw the rear adjuster foot in a reverse
direction.
Do not look into
the lens while the lamp is on.
The strong light from the lamp
may cause damage to your
eyes.
If the projector is not placed on a flat surface or the
screen and the projector are not perpendicular to each
other, the projected image becomes trapezoidal. To
correct this situation, see "Correcting keystone" on
page 33 for details.
Be careful when you press the
adjuster button as it is close to
the exhaust vent where hot air
comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture
quality. To do this, press AUTO on the projector or
remote control. Within 3 seconds, the built-in
Intelligent Auto Adjustment function will re-adjust
the values of Frequency and Clock to provide the best
picture quality.
The current source information will be displayed in
the corner of the screen for 3 seconds.
The screen will be blank while AUTO is functioning.
Fine-tuning the image size and clarity
1.
32
Adjust the projected image to the size
that you need using the zoom ring.
2.
Then sharpen the image by rotating
the focus ring.
Operation
http://www.pureglare.com.au
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following ONE of these steps.
•
Press
/
on the control panel of the
projector or remote control to display the
Keystone correction page. Press
to
correct keystoning at the top of the image.
Press
to correct keystoning at the bottom
of the image.
Press MENU/EXIT on the projector or
remote control. Go to the DISPLAY >
Keystone and adjust the values by pressing
or
on the projector or remote
control.
•
Press
/
.
/
Press
Keystone
.
MENU
Back
Magnifying and searching for details on the
projected picture
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
1.
Press D. ZOOM +/- to display the Zoom bar.
Press D. ZOOM + to magnify the center of the
picture. Press the key repeatedly until the
picture size is suitable for your need.
2.
Use the directional arrows ( , , , ) on
the projector or remote control to navigate the
picture.
3.
To restore the picture to its original size, press
AUTO. You can also press D. ZOOM -. When
the key is pressed again, the picture is further
reduced until it is restored to the original size.
• Using the OSD menu
1.
Press MENU/EXIT and then press
/
until
the DISPLAY menu is highlighted.
2.
The picture can only be
navigated after the picture is
magnified. You can further
magnify the picture while
searching for details.
Press to highlight Digital Zoom and press
Mode/enter. The Zoom bar displays.
Operation
http://www.pureglare.com.au
33
3.
4.
5.
Press repeatedly to magnify the picture to a desired size.
To navigate the picture, press Mode/enter to switch to the paning mode and press the
directional arrows ( , , , ) on the projector or remote control to navigate the
picture.
To reduce size of the picture, press Mode/enter to switch back to the zoom in/out
function, and press AUTO to restore the picture to its original size. You can also press
repeatedly until it is restored to the original size.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input source.
To change the projected picture ratio (no matter what aspect the source is):
• Using the remote control
1.
Press ASPECT to show the current setting.
2.
Press ASPECT repeatedly to select an aspect ratio to suit the
format of the video signal and your display requirements.
• Using the OSD menu
1.
Press MENU/EXIT and then press
/
until the DISPLAY
menu is highlighted.
2.
3.
Press to highlight Aspect Ratio.
Press / to select an aspect ratio to suit the format of the
video signal and your display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas.
1.
2.
4:3: Scales an image so that it is displayed in the center of the screen
with a 4:3 aspect ratio. This is most suitable for 4:3 images like
computer monitors, standard definition TV and 4:3 aspect DVD
movies, as it displays them without aspect alteration.
16:9: Scales an image so that it is displayed in the center of the screen
with a 16:9 aspect ratio. This is most suitable for images which are
already in a 16:9 aspect, like high definition TV, as it displays them
without aspect alteration.
16:9 aspect ratio is only sourced through the Component Video input when
being fed an appropriate 16:9 aspect signal. See "Connecting a Component
Video source device" on page 23 and "Obtaining a preferred projected
image size" on page 15 for details.
3.
34
Auto: Scales an image proportionally to fit the projector's native
resolution in its horizontal width. This is suitable for the incoming
image which is either in 4:3 nor 16:9 and you want to make most use
of the screen without altering the image's aspect ratio.
Operation
http://www.pureglare.com.au
4.
Real: The image is projected as its original resolution, and resized to
fit within the display area. For input signals with lower resolutions,
the projected image will display smaller than if resized to full screen.
You could adjust the zoom setting or move the projector towards the
screen to increase the image size if necessary. You may also need to
refocus the projector after making these adjustments.
OSD menus can be displayed on those unused black areas.
Optimizing the image
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Wall Color feature can help correct the projected picture’s color to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Wall Color menu and press / to select a
color which is the closest to the color of the projection surface. There are several
precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and Blackboard
Selecting a picture mode
The projector is preset with several predefined picture
modes so that you can choose one to suit your
operating environment and input source picture type.
To select a operation mode that suits your need, you
can follow one of the following steps.
• Press Mode/enter on the projector or MODE on
the remote control repeatedly until your desired
mode is selected.
• Go to the PICTURE > Picture Mode menu and
press / to select a desired mode.
The picture modes available for different types of
signals are listed below.
NOTE: A slight variation in the
picture brightness and colors may
be observed during the very short
time of switching picture modes.
PC/DVI-A/DVI-D Signal Input
1.
Dynamic mode (Default): Maximizes the brightness of the projected image. This
mode is suitable for environments where extra-high brightness is required, such as
using the projector in well lit rooms.
2.
Presentation mode: Is designed for presentations. The brightness is emphasized in this
mode to match PC and notebook coloring.
3.
sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
4.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 36 for details.
Operation
http://www.pureglare.com.au
35
YPbPr/S-Video/Video/HDCP Signal Input
1.
Dynamic mode: Is suitable for playing gamebox-based video games in a normal living
room lighting level environment.
2.
Standard mode (Default): Is appropriate for viewing colorful movies, video clips from
digital cameras or DVs.
3.
Cinema mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
4.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 36 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/2) as a starting point
and customize the settings.
1.
2.
3.
Press MENU/EXIT to open the On-Screen Display (OSD) menu.
In the PICTURE menu, highlight Picture Mode and press / to select User 1 or
User 2.
Press
to highlight Reference Mode.
This function is only available when User 1, or User 2 mode is selected up in the Picture Mode
sub-menu item.
4.
5.
6.
7.
Press / to select an picture mode that is closest to your need.
Press to select a menu item to be changed and adjust the value with / . See
"Fine-tuning the image quality in user modes" below for details.
When all settings have been done, highlight Save Settings and press Mode/enter on the
projector or ENTER on the remote control to store the settings.
The confirmation message 'Setting Saved' displays.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 is selected. You can make adjustments to these functions based on
your needs.
Adjusting Brightness
Press BRIGHTNESS on the remote control or highlight
Brightness in the PICTURE menu and adjust the values
by pressing / on the projector or remote control.
+30
+50
+70
+30
+50
+70
The higher the value, the brighter the image. And lower
the setting, darker the image. Adjust this control so the
black areas of the image appear just as black and that
detail in the dark areas is visible.
Adjusting Contrast
Press CONTRAST on the remote control or highlight
Contrast in the PICTURE menu and adjust the values
by pressing / on the projector or remote control.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
36
Operation
http://www.pureglare.com.au
Adjusting Color
Highlight Color in the PICTURE menu and adjust the values by pressing
projector or remote control.
/
on the
Lower setting produces less saturated colors; setting to the minimum value makes the image
black and white. If the setting is too high, colors on the image will be overpowering, which
makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing
projector or remote control.
/
on the
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight Sharpness in the PICTURE menu and adjust the values by pressing /
on the
projector or remote control.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight Brilliant Color in the PICTURE menu and select by pressing
projector or remote control.
/
on the
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in picture. It enables a
greater than 50% brightness increase in mid-tone images, which are common in video and
natural scenes, so the projector reproduces images in realistic and true colors. If you prefer
images with that quality, select On. If you don’t need it, select Off.
On is the default and recommended selection for this projector. When Off is selected, the
Color Temperature function is not available.
Selecting a color temperature
Highlight Color Temperature in the PICTURE menu and adjust the values by pressing
on the projector or remote control.
/
There are four color temperature* settings available.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
T2: Makes images appear bluish white.
3.
T3: Maintains normal colorings for white.
4.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Operation
http://www.pureglare.com.au
37
3D Color Management
In most installation situations, color management will not be necessary, such as in
classroom, meeting room, or lounge room situations where lights remain on, or where
building external windows allow daylight into the room.
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction,
should you require it.
Proper color management can only be achieved under controlled and reproducible viewing
conditions. You will need to use a colorimeter (color light meter), and provide a set of
suitable source images to measure color reproduction. These tools are not provided with the
projector, however, your projector supplier should be able to provide you with suitable
guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you
select each color, you can independently adjust its range and saturation according to your
preference.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc. You can project any image
from the disc on the screen and enter the 3D Color Management menu to make
adjustments.
To adjust the settings:
1.
Go to the PICTURE menu and highlight 3D Color Management.
2.
Press Mode/enter on the projector or ENTER on the remote control and the 3D Color
Management page displays.
3.
Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4.
Press to highlight Hue and press / to select its range. Increase in the range will
include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
Yellow
range at 0, only pure red in the projected
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
Press to highlight Saturation and adjust its
values to your preference by pressing / .
Every adjustment made will reflect to the
BLUE
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
38
Operation
http://www.pureglare.com.au
6.
7.
8.
9.
Press to highlight Gain and adjust its values to your preference by pressing / .
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time
on the screen to help you achieve better time
management when giving presentations. Follow these
steps to utilize this function:
1.
2.
Press TIMER SETUP on the remote control or go
to the SYSTEM SETUP: Basic > Presentation
Timer menu and press Mode/enter to display the
Presentation Timer page.
Highlight Timer Period and decide the time
period by pressing / . The length of time can
be set from 1 to 5 minutes in 1-minute
increments and 5 to 240 minutes in 5-minute
increments.
If the timer is already on, the timer will restart whenever
the Timer Period is reset.
3.
Presentation Timer
Timer Period
15
Always
Timer Display
Top-Left
Timer Position
Timer Counting Direction
Count Down
Timer Audible Reminder
Off
On
Off
MENU Back
Press to highlight Timer Display and choose if
you want the timer to show up on the screen by
pressing / .
Selection
Description
Always
Displays the timer on screen throughout the presentation time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never
4.
Press to highlight Timer Position and set the timer
position by pressing / .
Top-Left
5.
Hides the timer throughout the presentation time.
Bottom-Left
Top-Right
5 min
5 min
5 min
Bottom-Right
Press to highlight Timer Counting Direction and select
your desired counting direction by pressing / .
Selection
Description
Count Up
Increases from 0 to the preset time.
Count down
Decreases from the preset time to 0.
6.
5 min
Press to highlight Timer Audible Reminder and decide if you want to activate
sound reminder by pressing / . If you select On, a double beep sound will be
heard at the last 30 seconds of counting down/up, and a triple beep sound will be
produced when the timer is up.
Operation
http://www.pureglare.com.au
39
7.
8.
To activate the presentation timer, press
and
press / to highlight On and press Mode/
enter.
A confirmation message displays. Highlight Yes
and press Mode/enter on the projector or ENTER
on the remote control to confirm. You will see the
message “Timer is On” displaying on the screen.
The timer start counting at the time the timer is
on.
NOTICE
Are you sure to turn on the
presentation timer?
Yes
No
To cancel the timer, perform the following steps.
• Using the remote control
Press TIMER ON/SHOW and press
/
to highlight Off and press ENTER.
• Using the OSD menu
1.
Enter the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press
Mode/enter. A confirmation message displays.
2.
Highlight Yes and press Mode/enter to confirm. You will see the message “Timer is
Off ” displaying on the screen.
How to use the TIMER ON/SHOW button?
The button is a multi-functional key.
• If the presentation timer is off, pressing this
button displays a confirmation message. You
can decide whether to activate the timer or
not by following the on-screen instruction.
• If the timer is already on, pressing this button
displays a confirmation message. You can
decide whether to restart, continue or turn
off the timer by following the on-screen
instruction.
Remote paging operations
Connect the projector to your PC or notebook
with a USB cable prior to using the paging
function. See "Connecting a computer" on page
18 for details.
You can operate your display software program
(on a connected PC) which responds to page up/
down commands (like Microsoft PowerPoint) by
pressing PAGE / on the remote control.
If remote paging function doesn't work, check if
the USB connection is correctly made and the
mouse driver on your computer is updated to
the latest version.
40
The remote paging function
cannot work with Microsoft®
Windows®98 operating system.
Windows®XP or higher operating
systems are recommended.
Operation
http://www.pureglare.com.au
Hiding the image
In order to draw the audience's full attention to the
presenter, you can use BLANK on the projector or remote
control to hide the screen image. The word 'BLANK'
appears in the corner of the screen while the image is
hidden. When this function is activated with an audio
input connected, the audio can still be heard.
You can set the blank time in the SYSTEM SETUP:
Basic > Blank Timer menu to let the projector return
the image automatically after a period of time when there
is no action taken on the blank screen. The length of time
can be set from 5 to 30 minutes in 5-minute increments.
If the preset time spans are not suitable for your
personation, select Disable.
No matter Blank Timer is activated or disabled, you can
press any key except PAGE / and LASER on the
remote control to restore the picture.
Once BLANK is pressed, the
projector lamp enters
Economic mode
automatically.
Do not block the projection
lens from projecting as this
could cause the blocking
object to become heated and
deformed or even cause a
fire.
Freezing the image
Press FREEZE on the remote control to freeze the
image. The word 'FREEZE' will display in the upper left
corner of the screen. To release the function, press any
button on the projector or remote control.
Even if an image is frozen on the screen, the pictures
are running on the video or other device. If the
connected devices have active audio output, you will
still hear the audio even though the image is frozen
onscreen.
Operation
http://www.pureglare.com.au
41
Utilizing FAQ function
The INFORMATION menu contains possible solutions to problems encountered by users
regarding image quality, installation, special feature operation and service information.
To get the FAQ information:
1.
Press /
on the projector or remote control
or press MENU/EXIT to open the OSD menu
and press /
to highlight the
INFORMATION menu.
2.
Press to select FAQ-Image and Installation or
FAQ-Features and Service based on the
information you want to know.
3.
Press Mode/enter on the projector or ENTER on
the remote control.
4.
Press / to select the a problem and press
Mode/enter on the projector or ENTER on the
remote control for possible solutions.
To exit the OSD menu, press MENU/EXIT.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except Power and LASER.
1.
2.
Press / on the projector or remote control or
go to the SYSTEM SETUP: Basic > Panel Key Lock
menu, and select On by pressing / on the
projector or remote control. A confirmation
message displays.
Highlight Yes and press Mode/enter on the
projector or ENTER on the remote control to
confirm.
To release panel key lock, press and hold /
remote control or projector for 3 seconds.
on the
You can also use the remote control to enter the
SYSTEM SETUP: Basic > Panel Key Lock menu and
press / to select Off.
42
•
Buttons on the remote control are still in use when
panel key lock is enabled.
•
If you press Power to turn off the projector without
disabling panel key lock, the projector will still be in
locked status the next time it is turned on.
Operation
http://www.pureglare.com.au
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 m
–3000 m above sea level, and temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such condition.
To activate the High Altitude Mode, go to the SYSTEM
SETUP: Advanced > High Altitude Mode, select On
by pressing / on the projector or remote control.
A confirmation message displays. Highlight Yes and
press Mode/enter on the projector or ENTER on the
remote control.
WARNING
We recommend you use the High
Altitude Mode by selecting it
whenever your environment is
higher than 1500 m.
Do you want to turn High Altitude
Mode on?
Yes
No
Operation under "High Altitude Mode" may cause a
higher decibel operating noise level because of
increased fan speed necessary to improve overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among BenQ logo, Black or
Blue screen, you can make your own startup screen that is a picture projected from your
computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen
from either a computer or video source. The rest steps are as follows.
• Using the remote control
1.
Press CAPTURE on the remote control.
2.
A confirmation message displays. Press CAPTURE
or ENTER again.
3.
The message 'Screen Capturing...' displays while the
projector is processing the picture. Please wait.
4.
If the action is successful, you see the message
'Captured Succeeded' on the screen. The captured
picture is saved as My Screen.
5.
To view the captured picture displayed as the startup
screen, set My Screen in the SYSTEM SETUP: Basic
> Splash Screen menu and restart the projector.
• Using the OSD menu
1.
Press MENU/EXIT and then press / until the SYSTEM SETUP: Basic menu is
highlighted.
2.
Press to highlight My Screen and press Mode/enter.
3.
Repeat steps 2-5 in the “Using the remote control” section to capture and view the
captured picture.
In the unlikely event that the capturing action fails, change your target picture.
Operation
http://www.pureglare.com.au
43
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure
you have made a correct connection to the projector audio input. See "Connection" on page
18 for how the audio input is connected.
Muting the sound
To temporarily turn off the sound,
1.
2.
3.
Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu
is highlighted.
Press to highlight Audio Settings and press Mode/enter on the projector or ENTER
on the remote control. The Audio Settings page displays.
Highlight Mute and press / to select On.
Adjusting the sound level
To adjust the sound level,
1.
Repeat steps 1-2 above.
2.
Press to highlight Volume and press
/
to select a desired sound level.
Turning off the Power on/off ring tone
To turn off the ring tone,
1.
Repeat steps 1-2 above.
2.
Press to highlight Power on/off ring tone and press
/
to select Off.
The only way to change Power on/off ring tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power on/off ring tone.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
•
•
•
44
Menu Display Time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the
length of time the OSD will remain active after your last button press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time.
Menu Position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD
position in five locations. Use / to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OnScreen (OSD) Menus. Use / to select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be
displayed during projector start-up. Use /
to select a screen.
Operation
http://www.pureglare.com.au
Shutting down the projector
1.
Press II Power and a confirmation message will
display prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
Press II Power a second time. The Power
indicator light flashes orange, the projection lamp
shuts down, and the fans will continue to run for
approximately 90 seconds to cool down the
projector.
To protect the lamp, the projector will not respond to any
commands during the cooling process.
To shorten the cooling time, you can also activate the
Quick cooling function. See "Quick Cooling" on page 51
for details.
3.
Once the cooling process finishes, a "Power Off
Ring Tone" will be heard. The Power indicator light
is a steady orange and fans stop. Disconnect the
power cord from the wall socket.
•
To turn off the power ring tone, see "Turning off the
Power on/off ring tone" on page 44 for details.
•
If the projector is not properly shut down, to protect
the lamp, when you attempt to re-start the projector,
the fans will run for a few minutes to cool down. Press
Power again to start the projector after the fans stop
and the Power indicator light turns orange.
Operation
http://www.pureglare.com.au
45
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
Main menu
Sub-menu
Wall Color
1.
DISPLAY
Aspect Ratio
Keystone
Position
Phase
H. Size
Digital Zoom
Options
Off/Light Yellow/Pink/Light
Green/Blue/Blackboard
4:3/16:9/Auto/Real
PC source: Dynamic/Presentation/sRGB/Cinema/
User 1/User 2
Video source: Dynamic/Standard/Cinema/User 1/
User 2
PC source: Dynamic/Presentation/sRGB/Cinema
Reference Mode
Video source: Dynamic/Standard/Cinema
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color
On/Off
Color Temperature
T1/T2/T3/T4
Primary Color
R/G/B/C/M/Y
Hue
3D Color
Management
Saturation
Gain
Save Settings
Quick Auto Search
On/Off
Color Space Conversion
RGB/YUV
Picture Mode
2.
PICTURE
3. SOURCE
FAQ-Image and Installation
FAQ-Features and Service
6.
INFORMATION Current System Status
46
Operation
http://www.pureglare.com.au
•
•
•
•
•
Source
Picture Mode
Resolution
Color System
Equivalent Lamp Hour
Timer Period
Timer Display
Presentation
Timer
4.
SYSTEM
SETUP:
Basic
Timer Position
Timer Counting
Direction
Timer Audible
Reminder
On/Off
Count Down/Count Up
On/Off
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Timer Controller
5.
SYSTEM
SETUP:
Advanced
1~240 minutes
Always/1 min/2 min/3 min/Never
Bottom-Right/Top-Right/BottomLeft/Top-Left
Splash Screen
My Screen
Quick Cooling
High Altitude Mode
Mute
Volume
Audio Settings
Power on/off ring
tone
Menu Display
Time
Menu Settings
Menu Position
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Disable/5 min/10 min/15 min/20
min/25 min/30 min
On/Off
Disable/30 min/1 hr/2 hr/3 hr/4
hr/8 hr/12 hr
BenQ/Black/Blue/My Screen
On/Off
On/Off
On/Off
On/Off
5 sec/10 sec/15 sec/20 sec/25
sec/30 sec
Center/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
Normal/Economic
Lamp Mode
Reset Lamp Timer
Equivalent Lamp Hour
Change Password
Security
Change Security Settings
Settings
• Power On Lock
• Splash Screen Lock
Reset All Settings
Lamp Settings
Note that the menu items are available when the projector detects at least one valid signal. If
there is no equipment connected to the projector or no signal detected, limited menu items
are accessible.
Operation
http://www.pureglare.com.au
47
DISPLAY menu
FUNCTION
(default setting/
value)
DESCRIPTION
Wall Color
Correct the projected picture’s color when the projection surface is not
white. See "Using Wall Color" on page 35 for details.
(Off)
Aspect Ratio
(Auto)
Keystone
(0)
Position
(0)
Phase
(depends on the
selected input
source)
H. Size
There are four options to set the image's aspect ratio depending on your
input signal source. See "Selecting the aspect ratio" on page 34 for
details.
Corrects any keystoning of the image. See "Correcting keystone" on page
33 for details.
Displays the position adjustment page. To move the projected image,
use the directional arrow buttons. The values shown on the lower
position of the page change with every button press you made until they
reach their maximum or minimum.
Adjusts the clock phase to reduce image
distortion.
Adjusts the horizontal width of the image.
(depends on the
selected input
source)
Digital Zoom
(100%)
Magnifies or reduces the projected image. See "Magnifying and
searching for details on the projected picture" on page 33 for details.
SOURCE menu
FUNCTION
(default setting /
value)
DESCRIPTION
Quick Auto
Search
See "Switching input signal" on page 31 for details.
(On)
Color Space
Conversion
See "Changing Color Space" on page 31 for details.
(RGB)
48
Operation
http://www.pureglare.com.au
PICTURE menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default setting / DESCRIPTION
value)
Picture Mode Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a picture
(PC/DVI-A/DVI- mode" on page 35 for details.
D: Dynamic;
YPbPr/ S-Video/
Video:
Standard)
Reference
Mode
Brightness
Contrast
Color
(0)
Tint
(0)
Sharpness
(15)
Brilliant
Color
Selects an picture mode that most suits your need for the image quality
and further fine-tune the image based on the selections listed on the same
page below. See "Setting the User 1/User 2 mode" on page 36 for details.
Adjusts the brightness of the image. See "Adjusting Brightness" on page 36
for details.
Adjusts the degree of difference between dark and light in the image. See
"Adjusting Contrast" on page 36 for details.
Adjusts the color saturation level -- the amount of each color in a video
image. See "Adjusting Color" on page 37 for details.
Adjusts the red and green color tones of the image. See "Adjusting Tint"
on page 37 for details.
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 37 for details.
See "Adjusting Brilliant Color" on page 37 for details.
(On)
There are four color temperature settings are available. See "Selecting a
Color
color temperature" on page 37 for details.
Temperature
(T3)
See "3D Color Management" on page 38 for details.
3D Color
Management
Save
Settings
Saves the settings made for User 1 or User 2 mode.
Operation
http://www.pureglare.com.au
49
SYSTEM SETUP: Basic menu
FUNCTION
(default setting /
value)
DESCRIPTION
Presentation
Timer
Reminds the presenter to finish the presentation within a certain time
frame. See "Setting the presentation timer" on page 39 for details.
Language
Sets the language for the On-Screen Display (OSD) menus. See "Using the
menus" on page 27 for details.
Projector
Position
The projector can be installed on a ceiling or behind a screen, or with one
or more mirrors. See "Choosing a location" on page 14 for details.
(Front Table)
Auto Power
Off
(Disable)
This function allows the projector to turn off automatically if no input
signal is detected after a set period of time. See "Setting Auto Power Off "
on page 54 for details.
(Disable)
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen. See "Hiding the image" on
page 41 for details.
Panel Key
Lock
Disables or enables all panel key functions except Power on the projector
and buttons on the remote control. See "Locking control keys" on page 42
for details.
Blank Timer
(Off)
Timer
Controller
Sets the auto-shutdown timer. The timer can be set to a value between 30
minutes and 12 hours.
(Disable)
Splash
Screen
(BenQ logo)
My Screen
50
Allows you to select which logo screen will display during projector startup. Four options are available: BenQ logo, Black screen, Blue screen or My
Screen.
Captures and stores the projected picture as My Screen. See "Creating your
own startup screen" on page 43 for details.
Operation
http://www.pureglare.com.au
SYSTEM SETUP: Advanced menu
FUNCTION
(default setting /
value)
DESCRIPTION
Quick
Cooling
Enables or disables the Quick Cooling function. Selecting On enables the
function and projector cooling time will be shortened from a normal 90second duration to approximately 30 seconds.
(On)
High Altitude A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 43 for details.
Mode
(Off)
Audio
Settings
Menu
Settings
Mute (Off)
Volume (5)
Power on/off ring tone (On)
See "Adjusting the sound" on page 44 for details.
Menu Display Time (5 sec)
Sets the length of time the OSD will remain active after your last button
press. The range is from 5 to 30 seconds in 5-second increments.
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
Lamp Mode (Normal)
Setting the projector in Economic mode also extends the lamp timer
automatic shutdown feature. See "Setting Lamp Mode as Economic" on
page 54 for details.
Lamp
Settings
Reset Lamp Timer
Once the lamp is renewed, select Reset to return the lamp timer to '0'. See
"Resetting the lamp timer" on page 58 for details.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used. See "Getting to
know the lamp hour" on page 54 for details on how the total lamp hour is
calculated.
Security
Settings
Reset All
Settings
Change Password
You will be asked to enter the current password before changing to a new
one. See "Utilizing the password function" on page 28 for details.
Change Security Settings
Power On Lock (Off)
Splash Screen Lock (Off)
See "Utilizing the password function" on page 28 for details.
Returns all settings to the factory preset values.
The following settings will still remain: Position, Phase, H. Size, User
1, User 2, Language, Projector Position, High Altitude Mode.
Operation
http://www.pureglare.com.au
51
INFORMATION menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
DESCRIPTION
FAQ-Image and
Installation
FAQ-Features
and Service
Displays possible solutions to problems you may encounter.
Source
Shows the current signal source.
Picture mode
Shows the selected mode in the PICTURE menu.
Current System
Status
Resolution
Shows the native resolution of the input signal.
Color system
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
52
Operation
http://www.pureglare.com.au
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner
and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 45 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
•
•
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 61 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the batteries from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When
you carry the projector yourself, please use the original box or provided soft carry case.
Maintenance
http://www.pureglare.com.au
53
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as
follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) + 4/3 (hours used in normal mode)
See "Setting Lamp Mode as Economic" below for more information on Economic mode.
The lamp hour in Economic mode is calculated as 3/4 of that in normal mode. That is, using
the projector in Economic mode helps to extend the lamp hour by 1/3.
To obtain the lamp hour information:
1.
Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu
is highlighted.
2.
Press to highlight Lamp Settings and press Mode/enter. The Lamp Settings page
displays.
4.
You will see the Equivalent Lamp Hour information displaying on the menu.
5.
To leave the menu, press MENU/EXIT.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item that normally can last up to 3000-4000 hours
with proper usage. To keep the lamp life as long as possible, you can do the following settings
via the OSD menu.
• Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp Mode
menu and press / .
• Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and
press / . The time period can be set from 5 to 30 minutes in 5-minute increments. If the
preset time lengths are not suitable for your presentation, select Disable. The projector will
not automatically shut down in a certain time period.
54
Maintenance
http://www.pureglare.com.au
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 59 for details.
The following Lamp warning displays will remind you to change the lamp.
Status
Message
The lamp has been in operation for 3000 hours.
Install a new lamp for optimal performance. If the
projector is normally run with "Economic Mode"
selected (See "Lamp Mode (Normal)" on page 51),
you may continue to operate the projector until
the 3950 hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp > 3000 Hours
OK
The lamp has been in operation for 3950 hours. A
new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
Notice
Replace Lamp Soon
Lamp > 3950 Hours
OK
The lamp has been in operation for 4000 hours.
Notice
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced after
3000 hours usage.
The lamp MUST be replaced before the projector
will operate normally.
Replace Lamp Now
Lamp > 4000 Hours
Lamp usage time exceeded
OK
Notice
Lamp-usage time exceeded
Replace lamp (refer to User manual)
Then reset lamp timer
OK
Maintenance
http://www.pureglare.com.au
55
Replacing the lamp
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
•
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
•
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
•
To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
•
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
•
To assure optimal performance from the projector, it is recommended that you purchase a
BenQ projector lamp for lamp replacement.
•
If lamp replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury
or damage to the human eyes caused by fractured lamp.
1.
Turn the power off and disconnect the projector from the wall socket. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
2.
Use a coin to turn the screw counterclockwise
until the lamp cover loosens.
3.
Do not turn the power on with the lamp cover
removed.
•
Do not insert your fingers between the lamp and
the projector. The sharp edges inside the
projector may cause injuries.
4.
56
Remove the lamp cover from the projector.
•
Loosen the screw that secures the lamp.
Maintenance
http://www.pureglare.com.au
5.
Lift the handle so that it stands up. Use the
handle to slowly pull the lamp out of the
projector.
•
Pulling it too quickly may cause the lamp to break
and scatter broken glass in the projector.
•
Do not place the lamp in locations where water
might splash on it, children can reach it, or near
flammable materials.
•
Do not insert your hands into the projector after
the lamp is removed. If you touch the optical
components inside, it could cause color
unevenness and distortion of the projected
images.
6.
7.
As shown in the figure, lower the new lamp
first into the connector on the projector and
align the two holes on the projector.
Tighten the screw that secures the lamp.
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
8.
Ensure the handle is fully laid flat and
locked in place.
9.
Replace the lamp cover on the projector.
Maintenance
http://www.pureglare.com.au
57
10.
Use a coin to turn the screw clockwise until the
lamp cover is secured.
•
Loose screw may cause a bad connection, which
could result in malfunction.
•
Do not over tighten the screw.
11.
Restart the projector.
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
12. After the startup logo, open the On-Screen
Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings menu.
Press Mode/enter on the projector or ENTER
on the remote control. The Lamp Settings
page displays. Highlight Reset Lamp Timer. A
warning message displays asking if you want
to reset the lamp timer. Highlight Reset and
press Mode/enter on the projector or ENTER
on the remote control. The lamp time will be
reset to '0'.
Notice
Do not reset if the lamp is not new or replaced as
this could cause damage.
58
Maintenance
http://www.pureglare.com.au
Reset Lamp Timer?
Reset
Cancel
Indicators
Light
Power
Status & Description
Temp
Lamp
Power events
Orange
Orange
Orange
Orange
Off
Off
The projector has just been connected to a power outlet or the
lamp door is open.
Stand-by mode.
Green
Flashing
Off
Off
Powering up.
Green
Off
Off
Orange
Flashing
Off
Off
Orange
Flashing
Off
Off
Normal operation.
1.
The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling down
process. Or
2.
The projector needs to cool for 90 seconds after the
power is turned off.
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
Lamp events
Orange
Flashing
Off
Red
Off
Off
Red
The projector has shutdown automatically. If you try to re-start
the projector, it will shutdown again. Please contact your dealer
for assistance.
1.
The projector needs 90 seconds to cool down. Or
2.
Please contact your dealer for assistance.
Thermal events
Off
Red
Off
Off
Red
Red
Off
Red
Green
Off
Red
Orange
Red
Red
Red
Red
Red
Green
Red
Red
Green
Red
Orange The projector has shutdown automatically. If you try to re-start
Red
the projector, it will shutdown again. Please contact your dealer
Green
Red
Green
Green
Red
Orange
Orange
Red
Red
Orange
Red
Green
Orange
Red
Orange
Off
Green
Red
Off
Green
Green
for assistance.
Maintenance
http://www.pureglare.com.au
59
Troubleshooting
The projector does not turn on.
Cause
Remedy
There is no power from the power
cable.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input source device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The lens cover is still closed.
Open the lens cover.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the unit if necessary.
The lens cover is still closed.
Open the lens cover.
Remote control does not work
Cause
Remedy
The batteries are out of power.
Replace the batteries with new ones.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
The password is incorrect
Cause
Remedy
You do not remember the password.
60
Please see "Entering the password recall procedure" on page 30 for details.
Troubleshooting
http://www.pureglare.com.au
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Input terminals
Resolution
1024 x 768 XGA
Display system
1-CHIP DMD
Lens F/Number
F=2.4 to 2.48, f= 20.7 to 22.8 mm
Lamp
280 W lamp
Computer input
RGB input
D-Sub 15-pin (female) x 1
DVI-I input
Video signal input
S-VIDEO
Mini DIN 4-pin port x 1
VIDEO
RCA jack x 1
SD/HDTV signal input
Analog - Component RCA jack x 3
(through RGB input)
Digital - DVI (supports HDCP)
Audio signal input
Audio in
PC audio jack
Electrical
Power supply
AC100–240V, 4.5A, 50-60 Hz (Automatic)
Power consumption
365 W (Max); 5 W (Standby)
Mechanical
Environmental Requirements
Weight
7.7 lbs (3.5 Kg)
Output terminals
RGB output
D-Sub 15-pin (female) x 1
Speaker
(Stereo) 2 watt x 1
12VDC (Max. 1A)
Operating temperature
0°C–40°C at sea level
Operating relative humidity
10%–90% (without condensation)
Operating altitude
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with
High Altitude Mode on)
Control
USB serial control
Type mini B
RS-232 serial control
Mini Din 8 pin x 1
Specifications
http://www.pureglare.com.au
61
Dimensions
274.87 mm (W) x 131.30 mm (H) x 304.99 mm (D)
274.87
304.99
131.30
48.57
62
Specifications
http://www.pureglare.com.au
74.30
Timing chart
Supported timing for PC (including DVI-D) input
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
47.77
49.65
63.981
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.09
59.96
60.020
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
80.768
83.458
108.000
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
SXGA_60
SXGA_60
SXGA_60
15.75
31.47
31.25
37.50
45.00
33.75
67.5
28.13
33.75
67.5
60
60
50
50
60
60
60
50
60
60
13.51
27
27.000
74.25
74.25
74.25
148.5
74.25
74.25
148.5
480i
480p
576p
720p_50
720p_60
1035i
1035p
1080i_50
1080i_60
1080p
640 x 480
720 x 400
800 x 600
1024 x 768
1280 x 768
1280 x 800
1280 x 1024
VIDEO
(HDCP)
Mode
Supported timing for Component-YPbPr input
Signal Format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
Horizontal
Frequency (kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
Vertical Frequency
(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
Specifications
http://www.pureglare.com.au
63
Supported timing for Video and S-Video inputs
Video mode
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
64
Horizontal
Frequency
(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
Vertical
Frequency
(Hz)
60
50
50
60
50
60
60
Specifications
http://www.pureglare.com.au
Color subcarrier
Frequency
(MHz)
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be inbetween 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright 2007 by BenQ Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission of
BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties, merchantability
or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise
this publication and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Warranty and Copyright information
http://www.pureglare.com.au
65
Regulation statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC statement
This machine was tested against the 89/336/EEC (European Economic Community) for
EMC (Electronic Magnetic Compatibility) and fulfills these requirements.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households in the
European Union.
This symbol on the product or on the packaging indicates that this can not
be disposed of as household waste. You must dispose of your waste
equipment by handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment. For more information
about recycling of this equipment, please contact your city office, the shop
where you purchased the equipment or your household waste disposal
service. The recycling of materials will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
environment.
66
Regulation statements
http://www.pureglare.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement