MMM IIIC CC OOO MMM ---2 22R RR SSS

MMM IIIC CC OOO MMM ---2 22R RR SSS
Ruggedized HF-SSB ALE Mobile/Fixed Digital Signal Processing
Radio 125watt PEP/Average 1.6-30 MHz
RECEIVER
Model Number:
Frequency Range:
Number of Channels:
Scanning:
Frequency Stability:
Frequency Drift (Aging):
Synthesizer Lock Time:
Frequency Resolution:
Audio Bandwidths @ -6dB:
M85AMN0KV5-K
1.6 MHz Tx, 100 KHz-30 MHz Rx
200
5 groups with up to 100 channels per group
0.6 PPM, (0.1 PPM optional)
1 PPM per year
10 msec max.
10 Hz
Voice: 350 to 2700 Hz
CW: 650 to 1150 Hz
Low speed data: 1450 to 1950 Hz
High speed data*: 350 to 3300 Hz
Operating Temp. Range: -300 to +600C
Humidity: -95% @ 500C
Operating Voltage: 13.8 VDC ±20% Neg. Ground
ALE: Per FED-STD 1045 and Mil-STD 188/141A
Current Drain
Receive
Transmit
Squelched Full Audio Voice 2 Tone 1 Tone
@ 13.8 VDC
2.2A
3A
14A
23A
28A
@ 26.4 VDC
1.3A
1.8A
8A
13A
16A
Dimensions
Height
Width
Depth
Weight
and Weight
mm/inch mm/inch mm/inch
Kg
Lb
92 / 3.7
302 / 11.9 285 / 11.3
5.9
13
* Optional, for authorized users only
TRANSMITTER
Output Power:
Reduced Power Levels:
Audio Bandwidth Ripple:
Intermodulation:
Harmonic Emissions:
Spurious Emissions:
Carrier Suppression:
Undesired Sideband
Suppression:
Audio Distortion:
1/2 Power Mic. Sensitivity:
Hum & Ripple:
Inband Noise:
Tx/Rx Switching Time:
Tx Tuning Adjustments:
125w P.E.P. and average
25W, 62W 100W (RSS Programmable)
3 dB
-31 dB/P.E.P. (-35 dB/P.E.P. Typical Note 1)
-64 dB/P.E.P. (-70 dB/P.E.P. Typical Note 1)
-64 dB/P.E.P. (-70 dB/P.E.P. Typical Note 1)
-50 dB/P.E.P.
-55 dB/P.E.P.
2.5%
25 to 125 mV (RMS)/600 ohms
-50 dB
-60 dB (30 Hz BW)
10 msec
None
Note 1: Values noted as typical are valid over 90% or more of the frequency range.
OPTIONS
OPTIONS
RS232 Remote Contol Interface
Linear Amplifier Interface
Phone Patch Interface
Data/Fax Modem Interface
Micom-Link Interface
24 VDC Operation
Rss for PC (Radio and ALE)
High (0.1 PPM) Frequency stability
Multinet Operation (for A.L.E)
Communications
Composite
CM
MY
CY CMY
K
MICOM-2RS
Front Mount
GENERAL
Y
Sensitivity (SINAD) SSB: 0.5µv for 10 dB SINAD
(Voice) (0.3µv Typically.)
0.1-1.6 MHz - reduced performance
1/2 Rated Power Sensitivity: 1µv for 2.5W audio @ speaker
Selectivity: -6 dB @ 350 to 2700 Hz
-60 dB @ -1 kHz, +4 kHz
Image Rejection: -80 dB
IF Rejection: -85 dB
Undesired Sideband Rejection: -55 dB @ -1 kHz
Spurious Rejection: -80 dB
Intermediation Rejection: -80 dB
Cross Modulation Rejection: -100 dB @100 kHz
Desensitization: -100 dB @100 kHz
Reciprocal Mixing: -100 dB @100 kHz
Audio Power @ Speaker: 5W @ 2.5% distortion
RGC Range: 5µv 1V (2 dB change in output level)
RGC Time Constant Voice: Attack time 10 msec
Release time 1500 msec
Data: Attack time 10 msec
Release time 10 msec
Squelch: Constant SINAD (digital)
Clarifier Range: ±200 Hz in 10 Hz steps
Receiver Tuning Adjustments: None
Preselector Sections: Sub-octave (1.6 MHz to 30 MHz range)
Antenna Input Protection: 20 kV maximum transient, 100V RMS for
2 minutes
Ruggedized HF-SSB ALE Mobile/Fixed
Digital Signal Processing Radio
125watt PEP/Average 1.6-30 MHz
Features
MILITARY & INDUSTRIAL STANDARDS
Micom-2RS meets the following US military and industrial standard requirements
for adverse environmental conditions (without the need external shock mounts)
Environmental
Condition
US Military
STD 810C
US Military
STD 810D
US Military
STD 810E
Vibration
Shock
Rain
Dust
Salt Fog
Method 514.2
516.2
506.1
510.1
509.1
Method 514.3
516.3
506.2
510.2
509.2
Method 514.4
516.4
506.3
510.3
509.3
The Micom-2RS also meets the EIA-RS152B for shock, vibration and
applicable test procedures, US FCC for channel occupancy, spurious,
interference and frequency tolerance. It is manufactured according to the
demanding standards ISO 9001 and EMC (Electromagnetic Compatibilty).
FCC information; Emissions: J3E, R3E, H3E, J2A, J2B
FCC Applicable Parts of Rules: 15, 80, 90
FCC Type Acceptance Number : ABZ9QCC1635
With High Stability Option: ABZ9QCC1634
MAJOR ACCESSORIES
Phone Patch
Micom-Link (FM-HF repeater)
Automatic Antenna Tuner
Continuous Duty Kit
Military Audio Accessories
Automatic Telephone Interconnect
MOBAT Communications
3 Israeli Shimon St. P.O. 5090
Ind. zone rishon le Zion 75151 Israel
Tel: 972 3 9518050
Fax 972 3 9527233
E-mail: govers@mobat.com
web: www.mobat.com
Encryption Voice/Data
AC Power Supply
1 kW Amplifier
Antennas and Grounding kit
Data/Fax Modem
CW Key & Headphones
MOBAT USA
1720 west Paul dirc dr.
Tallahassee fl. 32310
Tel: 850 580 0444
Fax 850 580 2626
E-mail: marketing@mobatusa.com
web: www.mobat.com
Distributor
Front Mount
M
icom-2RS is an advanced Ruggedized
Digital Signal Processing transceiver,
intended for very wide area radio
communications. It provides, Voice, Data,
Fax and E-mail solutions with a high
degree of sophistication, signal quality
and reliability, while being very simple to
operate.
MICOM-2RS with its compact size
provides maximum ease of installation.
The Automatic Link Establishment-ALE
(per FED-STD 1045 and MIL-STD
188/141B) is a Standard Feature.
Enhanced DSP based Radio Platform
Enhanced features for better communication
Ruggedized Mobile / Fixed Transceiver
Front panel programming
Advanced digital technology
Conforms to MIL-STD 810 and EIA Specifications
ALE per FED-STD-1045 and MIL-STD-188/141B
High MTBF
Security access code
Variable Bandwidth for optimal signal processing
Voice activated digital squelch
Programmable channel scan
Digital noise blanking and clarifier
Guard and Priority Channels
Continuous duty operation (optional)
Multi-language Liquid Crystal Display
BITE (Built-in Test)
Meets FCC and EMC standards
Selectable front-end Attenuator
Enhanced Voice Quality
Excellent frequency stability
Selectable Power Output
Small Size, Light Weight
Variable notch filter
Sub-octave pre-selector
Military type audio connectors
Military type accessories
Adaptable internal configuration options
Multinet Operation for A.L.E (optional)
Front Mount
MICOM-2RS
M
MICOM-2RS
C
Ruggedized HF-SSB ALE Mobile/Fixed Digital Signal Processing
Radio 125watt PEP/Average 1.6-30 MHz
RECEIVER
Model Number:
Frequency Range:
Number of Channels:
Scanning:
Frequency Stability:
Frequency Drift (Aging):
Synthesizer Lock Time:
Frequency Resolution:
Audio Bandwidths @ -6dB:
M85AMN0KV5-K
1.6 MHz Tx, 100 KHz-30 MHz Rx
200
5 groups with up to 100 channels per group
0.6 PPM, (0.1 PPM optional)
1 PPM per year
10 msec max.
10 Hz
Voice: 350 to 2700 Hz
CW: 650 to 1150 Hz
Low speed data: 1450 to 1950 Hz
High speed data*: 350 to 3300 Hz
Operating Temp. Range: -300 to +600C
Humidity: -95% @ 500C
Operating Voltage: 13.8 VDC ±20% Neg. Ground
ALE: Per FED-STD 1045 and Mil-STD 188/141A
Current Drain
Receive
Transmit
Squelched Full Audio Voice 2 Tone 1 Tone
@ 13.8 VDC
2.2A
3A
14A
23A
28A
@ 26.4 VDC
1.3A
1.8A
8A
13A
16A
Dimensions
Height
Width
Depth
Weight
and Weight
mm/inch mm/inch mm/inch
Kg
Lb
92 / 3.7
302 / 11.9 285 / 11.3
5.9
13
* Optional, for authorized users only
Sensitivity (SINAD) SSB: 0.5µv for 10 dB SINAD
(Voice) (0.3µv Typically.)
0.1-1.6 MHz - reduced performance
1/2 Rated Power Sensitivity: 1µv for 2.5W audio @ speaker
Selectivity: -6 dB @ 350 to 2700 Hz
-60 dB @ -1 kHz, +4 kHz
Image Rejection: -80 dB
IF Rejection: -85 dB
Undesired Sideband Rejection: -55 dB @ -1 kHz
Spurious Rejection: -80 dB
Intermediation Rejection: -80 dB
Cross Modulation Rejection: -100 dB @100 kHz
Desensitization: -100 dB @100 kHz
Reciprocal Mixing: -100 dB @100 kHz
Audio Power @ Speaker: 5W @ 2.5% distortion
RGC Range: 5µv 1V (2 dB change in output level)
RGC Time Constant Voice: Attack time 10 msec
Release time 1500 msec
Data: Attack time 10 msec
Release time 10 msec
Squelch: Constant SINAD (digital)
Clarifier Range: ±200 Hz in 10 Hz steps
Receiver Tuning Adjustments: None
Preselector Sections: Sub-octave (1.6 MHz to 30 MHz range)
Antenna Input Protection: 20 kV maximum transient, 100V RMS for
2 minutes
TRANSMITTER
Output Power:
Reduced Power Levels:
Audio Bandwidth Ripple:
Intermodulation:
Harmonic Emissions:
Spurious Emissions:
Carrier Suppression:
Undesired Sideband
Suppression:
Audio Distortion:
1/2 Power Mic. Sensitivity:
Hum & Ripple:
Inband Noise:
Tx/Rx Switching Time:
Tx Tuning Adjustments:
125w P.E.P. and average
25W, 62W 100W (RSS Programmable)
3 dB
-31 dB/P.E.P. (-35 dB/P.E.P. Typical Note 1)
-64 dB/P.E.P. (-70 dB/P.E.P. Typical Note 1)
-64 dB/P.E.P. (-70 dB/P.E.P. Typical Note 1)
-50 dB/P.E.P.
-55 dB/P.E.P.
2.5%
25 to 125 mV (RMS)/600 ohms
-50 dB
-60 dB (30 Hz BW)
10 msec
None
Environmental
Condition
US Military
STD 810C
US Military
STD 810D
US Military
STD 810E
Vibration
Shock
Rain
Dust
Salt Fog
Method 514.2
516.2
506.1
510.1
509.1
Method 514.3
516.3
506.2
510.2
509.2
Method 514.4
516.4
506.3
510.3
509.3
The Micom-2RS also meets the EIA-RS152B for shock, vibration and
applicable test procedures, US FCC for channel occupancy, spurious,
interference and frequency tolerance. It is manufactured according to the
demanding standards ISO 9001 and EMC (Electromagnetic Compatibilty).
FCC information; Emissions: J3E, R3E, H3E, J2A, J2B
FCC Applicable Parts of Rules: 15, 80, 90
FCC Type Acceptance Number : ABZ9QCC1635
With High Stability Option: ABZ9QCC1634
MAJOR ACCESSORIES
Phone Patch
Micom-Link (FM-HF repeater)
Automatic Antenna Tuner
Continuous Duty Kit
Military Audio Accessories
Automatic Telephone Interconnect
Mobat USA
1721West Paul Dirac Dr.
Tallahassee, Florida 32310
Tel: 850 580 0420 · Fax: 850 580 2626
marketing@mobatusa.com · www.mobat.com
Encryption Voice/Data
AC Power Supply
1 kW Amplifier
Antennas and Grounding kit
Data/Fax Modem
CW Key & Headphones
Mobat
A Tadiran Communications Division
3 Israeli Shimon St.,P.O.B 5090,Rishon leZion 75151 Israel
Tel: 972 3 9518050 · Fax: 972 3 9527233
marketing@mobat.com · www.mobat.com
This publication is issued to provide general outline information only and does not constitute a representation on behalf of the company. This publication may
not be used or reproduced for any purpose other than general acquaintance with the described products and it may be changed by the company without notice.
Composite
CY CMY
K
Front Mount
Ruggedized HF-SSB ALE Mobile/Fixed
Digital Signal Processing Radio
125watt PEP/Average 1.6-30 MHz
Features
Micom-2RS meets the following US military and industrial standard requirements
for adverse environmental conditions (without the need external shock mounts)
OPTIONS
OPTIONS
Micom-Link Interface
24 VDC Operation
Rss for PC (Radio and ALE)
High (0.1 PPM) Frequency stability
Multinet Operation (for A.L.E)
MY
MILITARY & INDUSTRIAL STANDARDS
Note 1: Values noted as typical are valid over 90% or more of the frequency range.
RS232 Remote Contol Interface
Linear Amplifier Interface
Phone Patch Interface
Data/Fax Modem Interface
CM
MICOM-2RS
Front Mount
GENERAL
Y
M
icom-2RS is an advanced Ruggedized
Digital Signal Processing transceiver,
intended for very wide area radio
communications. It provides, Voice, Data,
Fax and E-mail solutions with a high
degree of sophistication, signal quality
and reliability, while being very simple to
operate.
MICOM-2RS with its compact size
provides maximum ease of installation.
The Automatic Link Establishment-ALE
(per FED-STD 1045 and MIL-STD
188/141A) is a Standard Feature.
Enhanced DSP based Radio Platform
Enhanced features for better communication
Ruggedized Mobile / Fixed Transceiver
Front panel programming
Advanced digital technology
Conforms to MIL-STD 810 and EIA Specifications
ALE per FED-STD-1045 and MIL-STD-188/141A
High MTBF
Security access code
Variable Bandwidth for optimal signal processing
Voice activated digital squelch
Programmable channel scan
Digital noise blanking and clarifier
Guard and Priority Channels
Continuous duty operation (optional)
Multi-language Liquid Crystal Display
BITE (Built-in Test)
Meets FCC and EMC standards
Selectable front-end Attenuator
Enhanced Voice Quality
Excellent frequency stability
Selectable Power Output
Small Size, Light Weight
Variable notch filter
Sub-octave pre-selector
Military type audio connectors
Military type accessories
Adaptable internal configuration options
Multinet Operation for A.L.E (optional)
Communications
Front Mount
MICOM-2RS
M
MICOM-2RS
C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising