gfe - Tekno Group
G LO B A L
FIRE
EQUIPMENT
PRODUCT
INFORMATION
March 8, 2007
Revision 1.5
DATA SHEET
JUNO-NET
G LO B A L
FIRE
EN54 TESTED
(1 to 3 Loop Panel)
Analogue Addressable Control Panel
EQUIPMENT
Juno-Net is a powerful Analogue Addressable fire Alarm control system with networking capabilities that
facilitate the configuration of complex wide area Fire detection systems.
Modular construction and distributed intelligence allow systems of
up to 96 Loops to be constructed. With a high level of built in
redundancy and emergency back up features the Juno-Net is fully
equipped to control the most complex installations.
Using its wide array of interfacing capabilities the Juno-Net is
ideally placed to provide an efficient and effective solution to the
logistics of protecting large institutions. Universities, Airports,
industrial complexes etc which may have many individual Fire Alarm
systems but require central reporting and control can easily be
accommodated by the advanced capabilities of the Juno-Net.
Juno-Net is available as a standalone system of up to 12 Loops in a
single cabinet and can be expanded to up to 96 Loops via a
networked array of sub-panels which can be supplied in a blank box
1 to 3 Loops
version or combined with a repeater to allow remote display and
EN54 APPROVED
control of the system. Networking is by a monitored redundant RS422/485, Fibre optic loop or TCP/IP
network. The Juno-Net networking capabilities are further enhanced by a wide range of programming
options which provide the capability to customise the system according to the needs of the customer. Flexible
cause and effect programming of I/O devices
and warning devices ensure that Fire or Fault
warnings trigger the appropriate response.
An interactive Graphic representation of the
system can be displayed on the users' computer
via the Odyssey Graphics software(Optional). All
the devices on the system can be displayed on a
building plan showing their status in real time. In
the event of Fire or fault the customer can control
the system and access all the necessary
information with a few mouse-clicks.
Automatic Device detection at start up reduces
time spent at the commissioning stage. In
1 to 12 Loops
Installation mode the Juno-Net detects and
recognises addressed and connected devices with the system being fully operational in less than two
minutes. The default programming ensures that the system is ready to detect Fire / fault alerts from the
moment that power is applied. Additional programming, to customise the system can be implemented via
the onboard keypad, IR programmer, PS 2 Keyboard or with a laptop PC running the GFE Loader software
which is available free of charge on the Global Fire website.
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
JUNO-NET
G LO B A L
FIRE
Analogue Addressable Control Panel
EQUIPMENT
Key Features
!
!
!
Fully expandable system from 1-96 Loops with distributed intelligence for added security.
125 device addresses per loop Apollo / WizMart, 254 Hochiki Protocol
Up to 96 Loop sounders with 32 individually programmable addresses per Loop
Apollo/WizMart protocol, 127 with Hochiki protocol.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
2 Fire output changeover relays
Open collector outputs for Fire, Fault and pre-alarm remote indication.
2 fully monitored sounder outputs on main panel and each sub panel.
Repeaters with optional integrated Sub-Panels
Black box option for Sub Panels
Detector loops fully monitored for integrity
384 programmable zones
512 fully programmable sounder and I/O groups
Event Log 2000 entries FIFO
Backlit LCD display 4 * 40
Multiple programming options, onboard keypad, Remote IR(Optional), PS2 Keyboard
Windows ™ based Loader Software for Programming with Laptop PC.
Windows™ based PC Graphics package for alarm management and reporting(Optional)
Multiple Language support(menu selectable)
BMS output RS 232(Optional)
Evacuate / Class Change input
SPECIFICATIONS
1 & 3 LOOPS
LOOPS
DISPLAY
SOUNDER OUTPUTS
SOUNDER GROUPS
AUX. RELAYS FIRE
AUX. RELAY FAULT
AUX POWER OUTPUT
ADDITIONAL OUTPUTS
PRIMARY SUPPLY
SECONDARY SUPPLY
POWER SUPPLY RATING
QUIESCENT CURRENT (NO DEVICES)
BATTERIES (INTERNAL)
DIMENSIONS
WEIGHT (NO BATTERIES)
OPERATING TEMPERATURE
STORAGE TEMPERATURE
HUMIDITY
PROTECTION CATEGORY
EMC - Same for all models
4 to 12 loops - max 250mA per loop
1 to 3 loops - max 250mA per loop
LCD 4 row/40 characters per row
LCD 4 row/40 characters per row
4/6/8 24Vdc/ 500mA each
2 at 24Vdc/400mA each
512
512
2 rated 50 VAC/DC 1A resistive
2 rated 50 VAC/DC 1A resistive
1 rated 50 VAC/DC 1A resistive
1 rated 50 VAC/DC 1A resistive
24Vdc 1A
24Vdc 460mA
Multiplexed up to 384 Programmable
Multiplexed up to 384 Programmable
85 - 265 Vac, 50/60Hz
85 - 265 Vac, 50/60Hz
24 Vdc Nominal
24 Vdc Nominal
150w
65w
130mA
130mA
2 x 12V 12 AH
2 x 12V 12 AH
H: 420 W: 550 D: 127 mm
H: 370 W: 340 D: 127 mm
8,1 Kg (no batteries)
5,1 Kg (no batteries)
0ºC to +40ºC
0ºC to +40ºC
-10 to +50ºC
-10 to +50ºC
max 85% no condensation
max 85% no condensation
IP
EMC Directive 89/336 and amendment 92/31 EEC & Low Voltage Directive 72/23 EEC
4 to 12 LOOPS
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
TECHNICAL SPECIFICATIONS
JUNO-NET
G LO B A L
FIRE
EQUIPMENT
Please note that these specifications apply to the stand-alone juno Net Analogue Addressable panel, 1 or
3 loops models, equipped with a 2.4 Amp power supply.
Empty:
5.1 Kg
Including sealed lead acid batteries:
2 x 12 V 7 AH I
10.5 Kg
2 x 12 V 12 AH
13.5 Kg
Weight:
Operating temperature:
0ºC to + 40ºC
Relative Humidity:
85% (non-condensing)
Conventional Sounder Circuits:
2 individually programmed. Both circuits current limited and monitored
for both open and short circuit fault conditions. 10k Ohm E.O.L.
resistors are used.
Maximum current rating/sounder circuit 400mA.
Auxiliary Relay Outputs:
2 voltage free changeover relay outputs used for fire indication.
1 voltage free relay output for fault indication. Remains energised
(normally closed) under normal condition and de-energises when any
fault condition appears on the system.
Maximum current rating for each relay contact 1A @ 50 V AC/DC
resistive.
Sensor / Loop Circuits:
1 loop or 3 loop models.
Supports analogue addressable devices over a 2 wire combined power
and digital data transmission loop.
Maximum single loop current loading is 250 mA. Maximum total
current load for 3 loops is 750mA.
Maximum recommended loop length is 1 Km with 1.5 mm2 wire crosssection.
Maximum cable capacitance 120 pF/m.
Minimum cable cross-section: 0.5 mm2
Maximum cable cross-section: 2.5 mm2
Power Supply and Charger
Input Operating Voltage:
85-264 V AC.
Power supply protection:
4 Amp - Fast Action
20 mm HRC
Fuse located on electrical mains connector TB, placed on top of the
aluminum PSU cover.
Maximum Continuous Primary
Power Supply Rating:
2.4 Amps @ 28 V DC nominal, comprising:
1 Amp max. temperature compensated, short circuit protected, battery
charger.
1.4 Amp used for internal electronic circuits and external ancillary
circuits: A maximum of 750 mA is available for loop power (250
mA/loop). Maximum of 150 mA for internal electronic circuits.
460 mA for auxiliary power supply output.
Under alarm conditions a maximum of 1 Amp current available for
conventional sounder circuits.
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
TECHNICAL SPECIFICATIONS
JUNO-NET
G LO B A L
FIRE
EQUIPMENT
Power Budget Quiescent
Condition:
a - 150 mA internal circuits
b - 460 mA auxiliary supply outputs
c - 750 mA for analogue loop power
d - 1 Amp for battery charger.
Alarm Condition:
800 mA for conventional sounder circuits +a+b+c
DC Output Voltage:
Maximum 27.5 V DC
Minimum 18.9 V DC
Max. Ripple Voltage:
1 V peak-to-peak @maximum output loading.
Battery Charger Output:
27.5 V DC nominal @ 20ºC
Secondary Supply:
24 V sealed lead acid batteries.
Minimum capacity 2 x 7 AH
Maximum capacity 2 x 12 AH
Both fitted internally.
Battery Fuse 3 A - 20 mm HRC
Repeater
Supply voltage
Quiescent current (without devices)
Dimensions
24V DC nominal
130mA
W 340mm x H 370mm x D 125mm
Standard Sub-panel
Primary supply voltage
EMC Standard
Secondary supply voltage
Power supply rating
Quiescent current (without devices)
Repeater outputs
Dimensions 1-9 loops
85 - 264 VAC
EN55022 class B
EN61000-4-2,3,4,5,6,8,11
EN61000-3-2,3
24V DC nominal
150W
80mA
Open collector 24V DC 100mA max
W 340mm x H 370mm x D 125mm
WARNING:In case of a short circuit or interruption of the analogue detection loop, only a maximum of 32
detectors or call points (per loop) can be prevented, at any given time, of transmitting a fire alarm. In order to
assure compliance with this clause, loop isolators have to be installed every 32 devices in the loop
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
JUNO-NET-REPEATER
G LO B A L
FIRE
Analogue Addressable Repeater Panel
EQUIPMENT
Juno-Net- Repeater
The Juno net repeater panel fully replicates the control panel information and control
facilities allowing multiple operating points within
the system. The J-Net repeater communicates with
the master control panel via an RS-422/RS-485,
Fiber Optic or TCP/IP network.
Sub-Panels can be integrated into the repeater panel
to allow the connection of up to three additional
detection loops, per sub-panel, to the system. Ideal
for multiple building complexes; where display and
control of the system is required in various locations.
Depending on control panel loading, power for the J-Net-Rep can be supplied from the
control panel’s auxiliary power output, an external 24Volt power supply or optionally can be
supplied complete with a built in 24V, 2,4A or 5A power supply unit. (Required if a sub-panel
is installed in the repeater housing.)
Repeater
Supply voltage
24V DC nominal
Quiescent current (without devices)
130mA
Dimensions
W 340mm x H 370mm x D 125mm
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
MINI-REPEATER
G LO B A L
FIRE
Analogue Addressable Repeater Panel
EQUIPMENT
Mini-Repeater
The mini-repeater is a fully functional mini version of the Juno-Net Repeater which can be
used with any distributed or self contained Juno-Net
based Fire Alarm system.
It's reduced dimensions make it ideal for installation
in reception areas or security booths where it would
be impractical and unattractive to install a full size
control panel. Like its big brother, the J-Net-Repeater,
the Mini-Rep permits full control of the system from
multiple locations. Connection to the Juno-Net or Junior is via an RS422/RS485, Fibre Optic
or TCP/IP interface. The Mini-Rep is supplied complete with an RS422/RS485 interface as
standard. Depending on control panel loading, power for the Mini-Rep can be supplied from
the control panel’s auxiliary power output or an external 24 Volt power supply.
Mini-Repeater
Supply voltage
24V DC nominal
Quiescent current
90mA
Dimensions
W 250mm x H 190mm x D 52mm
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
JUNO-NET-SUB-PANEL
G LO B A L
FIRE
Analogue Addressable Sub- Panel
EQUIPMENT
Juno-Net Sub-Panel
Juno-Net sub-panels allow expansion of the system in groups of 1 to 9 loops supplied in an
enclosed cabinet with independent primary and
secondary power supplies. Up to 9 Loops may be
installed in each cabinet which also contains a 5.4A
PSU/Charger unit and space for standby rechargeable
batteries. One RS422/RS485, Fibre Optic or TCP/IP
interface is required per cabinet to enable networking
with the rest of the system.
Each sub-panel board controls up to 3 Analogue
addressable detection loops via its own independent processor. In the event of
communications failure with the main control unit, the sub panel is capable of operating
independently, detecting fire/ fault events and activating its own sounders and I/O devices.
Standard Sub-panel
Primary supply voltage
EMC Standard
85 - 264 VAC
EN55022 class B
EN61000-4-2,3,4,5,6,8,11
EN61000-3-2,3
Secondary supply voltage
24V DC nominal
Power supply rating
150W
Quiescent current (without devices)
80mA
Alarm Outputs
2 monitored 10K EOL resistor, current limited 400mA,
Relay Outputs
2 programmable Alarm relay outputs 50V/1A,
1 Fault relay N/C
Dimensions 1-9 loops
W 340mm x H 370mm x D 125mm
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
JUNIOR V4
G LO B A L
FIRE
EQUIPMENT
Single Loop Analogue Addressable
Control Panel Expandable to Two Loops
The Global Fire Junior V4 is a single loop Analogue addressable control panel which can be expanded to
two loops. It provides a cost effective solution for small to medium sized installations. The Junior V4 can
support up to 125 addressable devices on each loop which are compatible with Apollo, Hochiki or WizMart
communications protocols.
Using Global Fires advanced communications mechanism up to 32
individually addressed Loop sounders can be connected to each of the
Junior V4 detection Loops. The Junior V4 also supports Shadow
sounders and GFE’s new Vulcan 2 addressable Sounder-BeaconIsolator along with all other GFE Interface devices.
The panel is equipped with a backlit LCD display of 4 rows each with 40
characters to give clear textual indications of Fire / Fault occurrences to
the end user.
There are also 16 Zone Fire LED indicators.
Mini-repeaters can be connected via an RS422/RS485, Fibre Optic or
TCP/IP interface to facilitate remote display and control of the system.
Automatic Device detection at start up reduces time spent at the commissioning stage. In Installation mode
the Junior V4 detects and recognises addressed and connected devices with the system being fully
operational in less than two minutes.
The default programming ensures that the system is ready to detect Fire / fault alerts from the moment that
power is applied. Additional programming, to customise the system can be implemented using a laptop PC
running the GFE Loader software which is available free of charge on the Global Fire website.
AVAILABLE IN 3 COLORS
RED-BLACK-WHITE
ORDERING INFO
JNR-V4-1
JNR-V4-2
JNR-V4-Card
J-NET-INT-485-NEW
LOADER
1 Loop Junior V4 Addressable Control Panel
2 Loop Junior V4 Addressable Control Panel
Junior V4 Loop card to expand 1 Loop to 2 Loops
Rs422/485 Interface Board to connect to Mini-Rep repeater panel
Programming Software freely downloadable from the Global Fire Website
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
JUNIOR V4
G LO B A L
FIRE
EQUIPMENT
Single Loop Analogue Addressable
Control Panel Expandable to Two Loops
Key Features
! Single loop panel - Expandable to two Loops using JNR-V4-Card
! Supports connection to Mini-repeaters via RS422/485, Fibre-Optic or TCP/IP interfaces
!
125 device addresses per loop
!
96 VULCAN (addressable) ultra low current base sounders (32 address limit) per Loop
!
32 individually programmable sounder addresses per Loop
!
Full SAM (Self Addressable Module) & MAM (Manually Addressable Module) support
(WizMart Protocol version)
!
2 Fire output relays (change-over) and 1 Fault relay (Normally closed)
!
2 conventional alarm outputs (Individually programmable)
!
Detector loops monitored for integrity
!
384 fully programmable zones
!
512 fully programmable sounder groups
!
512 fully programmable Input and Output groups
!
Event log (rolling, 2000 entries)
!
Compatible with Apollo S90™/XP95™, Discovery™, Hochiki and Wizmart Protocols
!
Compatible with all our own low cost ancillary modules
!
Backlit LCD display with 4 rows of 40 characters
!
Programming by Loader Software.
!
Multiple language support (menu selectable)
!
Integrated 16 zone LED fire zone indication
!
Interactive Discovery™ functions in the Apollo version
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
TECHNICAL SPECIFICATIONS
JUNIOR V4
G LO B A L
FIRE
EQUIPMENT
Please note that these specifications apply to the Junior V4 Analogue Addressable panel, 1 loop model,
equipped with a 1.7 Amp power supply @ 28.5V DC nominal.
Empty:
Weight:
1.6 Kg
Including sealed lead acid batteries:
2 x 12 V 7 AH
7.0 Kg
Dimensions:
W 274 x L 404 x H 109 mm
Operating temperature:
0ºC to + 40ºC
Relative Humidity:
85% (non-condensing)
Conventional Sounder Circuits:
2 individually programmed. Both circuits current limited and monitored
for both open and short circuit fault conditions. 10k Ohm E.O.L.
resistors are used.
Maximum current rating/sounder circuit 500mA.
Auxiliary Relay Outputs:
2 voltage free changeover relay outputs used for fire indication.
1 voltage free relay output for fault indication. Remains energised
(normally closed) under normal condition and de-energises when any
fault condition appears on the system.
Maximum current rating for each relay contact 1A @ 50 V AC/DC
resistive.
Sensor / Loop Circuits:
1or 2 loops
Max. number of devices per loop: 125
Supports analogue addressable devices over a 2 wire combined power
and digital data transmission loop.
Maximum recommended loop length is 1 Km with 1.5 mm2 wire crosssection. Maximum cable capacitance 120 pF/m.
Minimum cable cross-section: 0.5 mm2
Maximum cable cross-section: 2.5 mm2
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
TECHNICAL SPECIFICATIONS
JUNIOR V4
G LO B A L
FIRE
EQUIPMENT
Power Supply and Charger
Primary Supply:
85-264 V AC.
Input Operating Voltage:
4 Amp - Surge protected (slow blow)
20 mm HRC
Fuse located on electrical mains connector TB, placed above
the PSU inside the box.
Mains electrical fuse:
WARNING:In case of a short circuit or interruption of the analogue detection loop, only a maximum of 32
detectors or call points (per loop) can be prevented, at any given time, of transmitting a fire alarm. In order to
assure compliance with this clause, loop isolators have to be installed every 32 devices in the loop
Maximum Continuous Primary
Power Supply Rating:
1.7 Amps @ 28,5 V DC nominal, comprising:
1 Amp max. temperature compensated, short circuit protected,
battery charger.
400mA used for internal electronic circuits and external
ancillary circuits.
Maximum of 100 mA for internal electronic circuits.
300 mA for auxiliary power supply outputs.
Under alarm conditions a maximum of 800mA current
available for conventional sounder circuits.
Power Budget Quiescent
Condition:
a - 100 mA internal circuits
b - 300 mA auxiliary supply outputs
c - 275 mA for analogue loop power (550mA for 2 Loops)
d - 1 Amp for battery charger.
Alarm Condition:
800 mA for conventional sounder circuits +a+b+c
DC Output Voltage:
Maximum 28,5 V DC
Max. Ripple Voltage:
1 V peak-to-peak @ Maximum output loading.
Battery Charger Output:
27,5 V DC nominal @ 20ºC
Secondary Supply:
24 V sealed lead acid batteries.
Maximum capacity 2 x 7 AH
Both fitted internally.
Min. Voltage 21,0 V DC (Vb min)
Max. Voltage 27,2 V DC
Max. Current Output 1.7 Amp
Battery Fuse 1.7 A - Resettable
Electronic Fuse
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
ORION
G LO B A L
FIRE
Conventional Fire control panel
EQUIPMENT
The Orion range of conventional control panels features three models with 2, 4 and 8 Zones of detection.
Housed in a stylish modern ABS housing, the
Orion is the ideal control panel for smaller
installations.
Designed and manufactured to comply with
the requirements of EN54 parts 2 and
4(1998) the Orion uses active End of Line
monitoring to permit head removal
protection as required by Bs5839. (detector
bases must be fitted with Diode)
Programmable Zone coincidence and
alarm delay timer (0-10 min) are standard
features to help reduce false alarms.
The one man test facility enables simple and rapid testing of the system at commissioning and during
maintenance operations.
Features:
AVAILABLE IN 3 COLORS
RED-BLACK-WHITE
Two, four and eight zone non-expandable control panels.
Up to 32 conventional smoke and/or heat detectors per zone.
Active End of Line monitoring
Programmable non-latching zones
Delay timer programmable on/off per zone
Zone coincidence programmable for adjacent zones.
Two Access Levels
One man test
Supervised auxiliary 24 volt output
2 supervised/ monitored sounder circuits
2 programmable inputs for Class change, remote silence, remote reset etc.
2 Relay outputs fire and fault
ORDERING INFO
Power supply 1,5A at 28Vdc
ORION 2
Fully EN54 part 2 and 4 compliant
ORION 4
Future Features
ORION 8
Repeater output
Multiplexed output for Leds and additional relay outputs per zone
Addressable Loop Interface card
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
ORION
Conventional Fire control panel
G LO B A L
FIRE
EQUIPMENT
Technical Specifications
Mains supply voltage
Internal power supply
Total output current
Supply and battery charger monitored?
Batteries monitored
Max Battery size
Mains Fuse
Battery Fuse
Max Current Draw from Battery (Mains Fail)
85-264V 50/60 Hz
Min. 20 V DC – Max. 30 V DC (28.5 V DC nominal) Max. Ripple 1 V peak-peak
1,7A @230Vac
YES
YES
2 x 12V 7AH SLA
4 A – 250 V Slow Blow – 20 mm
1.6 Amp Resettable – Electronic Fuse
1.5 Amp Max.@ Max. Operating Temperature
Detection Circuit Specification
Number of circuits
Max Cable resistance
Max Cable Capacitance
Zone current quiescent
Zone current Alarm
End of Line Monitoring
BS5839 Detector removal compliant
Max. Number of Smoke/heat detectors per zone
Call point resistor value
2,4 or 8
40 Ω
0,470 μF
Max 5 mA
60mA max
Active EOL – CAPACITOR
YES provided diodes are fitted to detector base
32 – according to EN54 pt.2
470 to 680 Ohms
Sounder Circuit Specification
Number of circuits
End of Line Resistor value
Monitoring
Alarm Voltage
Sounder circuit Fuse
Max. Current available
2
10 K Ohms
Open and short circuit
27.5 V DC
1.1 Amp resettable ( Electronic Fuse )
1 Amp @ 27,5 V DC Nominal
Auxiliary Outputs
Aux power output
Fire relay
Fault relay
27.5 V DC Nominal – Max. Current Drawn 300 mA
Active in Fire condition, load 30V DC/1A resistive
Normally closed, fail safe open on any fault, load 30V DC/1A resistive
Auxiliary Inputs
Class Change / Evacuation
Remote Reset
Remote Silence
Non-Latching – Voltage free contact
Non-Latching – Voltage free contact
Non-Latching – Voltage free contact
Dimensions
Size
Weight without batteries
274 (W) x 404 (L) x 109 (H) mm
1,6 Kgs
Operating Conditions
Operating Temperature
Max Relative Humidity
0 to +40ºC
85% non condensing
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
QUAD-ZMU
Quad Zone Monitoring Unit
G LO B A L
FIRE
EQUIPMENT
Features:
24Vdc
EXTERNAL SUPPLY
FOR ZONE
The QUAD-ZMU is a fully monitored interface module which is used to connect up to four individually
addressed zones of current limited conventional detection devices to the Global Fire Addressable control
panel via the detection loop.
The module requires an external 24 volt power supply. Active End
of Line Monitoring with BS5839 Detector Removal compliance
when Diode bases are used (New Feature).
The detection Zones and their supply voltage are optically isolated
from the addressable detection loop which allows the use of a local
power supply.
If that supply fails, a fault condition is reported at the control panel.
The status of each zone is indicated by two LEDs. A red LED signals
Fire, Yellow indicates Fault on that zone. The normal state is
indicated by neither LEDs being illuminated. A Green LED
indicates the presence of 24 Volts. Irrespective of how many Zones are actually used, each QUAD-ZMU
occupies four consecutive addresses on the loop
LOOP OUT
L2
LOOP IN
L2
L1 OUT
L1 IN
L1 OUT
L1 IN
L2
L1 OUT
L1 IN
L1 OUT
L1 IN
L2
L2
L2
L1 OUT
L1 IN
L1 OUT
L1 IN
L2
L1 OUT
L1 IN
L1 OUT
L1 IN
L2
Active
End of Line
Capacitor
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
87 x 72 x 15mm
LOOP CURRENT QUIESCENT
2,9mA
WEIGHT (UNBOXED)
130 grams
LOOP CURRENT ALARM
3,1mA
OPERATING TEMPERATURE
0 - 40ºC
LOOP CURRENT FAULT - OPEN/SHORT
1,5/1,5mA
STORAGE TEMPERATURE
-10 - 50ºC
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
HUMIDITY
<85%Rh non condensing
EXTERNAL CURRENT QUIESCENT
7mA
MAX. Nº OF DETECTORS PER ZONE
32
EXTERNAL CURRENT ALARM
30mA
MAX CABLE SIZE
2,5 mm2
EXTERNAL CURRENT FAULT - OPEN/SHORT
1,5/60mA
MAX Nº OF QUAD-ZMU PER LOOP
31
ISOLATION
500 Vdc Max.
ORDERING INFORMATION
QUAD-ZMU
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
LSC-ISO
Loop Sounder Control Module
G LO B A L
FIRE
EQUIPMENT
(with 1Amp monitored output)
Features:
The LSC-ISO Module is a fully monitored interface which is used to connect a line of conventional sounders
to the Global Fire Addressable control panel via the detection loop.
The module requires an external 24 volt Dc power supply and can
supply up to 1A at the sounder output which is monitored for both open
and short circuit faults. A 10K ohm end of line resistor is connected to
the last sounder to provide line monitoring.
The LSC-ISO uses the Global Fire proprietary sounder control
protocol and therefore is only compatible with the GFE range of
control panels.
The output can be programmed as pulsed or continuous. A maximum
of 32 LSC-ISO can be connected to each Loop using address numbers
94 -125 inclusive.
Also available complete with housing.
OUTPUT TO
CONVENTIONAL
SOUNDERS
EXTERNAL
POWER SUPPLY
END OF LINE: 10K RES.
ADDRESS
SETTING
EXTERNAL
POWER SUPPLY
LOOP IN
LOOP OUT
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
58 x 48 x 20 mm
LOOP CURRENT QUIESCENT
1,3mA
WEIGHT (UNBOXED)
30 grams
LOOP CURRENT ALARM
1,5mA
OPERATING TEMPERATURE
0 - 40ºC
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
STORAGE TEMPERATURE
-10 to +50ºC
EXTERNAL CURRENT QUIESCENT
1,9mA
HUMIDITY
<85%Rh non condensing
EXTERNAL CURRENT MAX.
1A
MAX CABLE SIZE
2,5 mm2
ISOLATION
500 Vdc Max.
ORDERING INFORMATION
LSC-ISO
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
I/O
G LO B A L
FIRE
Addressable Input/Output Module
EQUIPMENT
Features:
The Addressable Input/Output Module is a fully monitored device which permits the interfacing of third party
equipment with the Fire Alarm Control panel using normally open dry contact connections while also providing a
changeover output relay to control ancillary equipment.
The connection to the input is monitored for fault (open or short circuit) and
Alarm conditions.
The output relay can be powered from the detection loop (default) or optionally
by an external 24Vdc supply. Relay operation is confirmed by an onboard yellow
LED.
The interface is used to monitor the contacts of an external system which must be
interfaced to the Fire Alarm System, for example a Flow Switch in a sprinkler
system to indicate if the sprinklers have been activated or extinguishant level
monitoring in Gas Extinguishing systems etc.
The output relay can be programmed to close fire doors, activate smoke removal
systems etc. The factory default setting is for the relay to receive its operating power from the Loop. Opening a link on
the underside of the PCB allows the use of external power which is optically isolated from the detection loop. This
option is recommended in the event that many I/O units are connected to the same Loop.
The Addressable I/O module is available as an electronic module with four fixing holes or as a boxed unit for field
installation.
LOOP OUT
Resistance values:
for Input
Fault -
LOOP IN
OPTIONAL 24 Vdc EXTERNAL SUPPLY
CUT LINKS (JP1 & JP2) IF REQUIRED
Short circuit to 2K2
or 50k to Open Circuit
Normal - 8K2 to 50k
Fire -
2K2 to 8K2
ADDRESS
SETTING
Output Relay:
N/O or N/C
Contact rating 50Vdc,
1A Resistive Loading
INPUT
OUPUT RELAY CONNECTIONS
COMMON / NO / NC
SPECIFICATIONS
SUPPLY
Loop Power / 24Vdc
DIMENSIONS (UNBOXED)
57 x 52 x 15 mm
LOOP CURRENT QUIESCENT
0,7mA
WEIGHT (UNBOXED)
30 grams
LOOP CURRENT INPUT ALARM
3,1mA
OPERATING TEMPERATURE
0 - 40ºC
LOOP CURRENT MAX. RELAY ACTIVE
18,1mA
STORAGE TEMPERATURE
-10 - 50ºC
RELAY CONTACT RATING
50 Vdc / 1A Resistive
HUMIDITY
<85 %Rh non condensing
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
PROTECTION CATEGORY
N/A
EXTERNAL CURRENT QUIESCENT
N/A
MAX CABLE SIZE
2,5 mm2
EXTERNAL CURRENT MAX.
3,1mA
ORDERING INFORMATION
IO-ISO
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
INPUT
Addressable Input Module
G LO B A L
FIRE
EQUIPMENT
Features:
The Addressable Input Module is a fully monitored device which
permits the interfacing of third party equipment with the Fire Alarm
Control panel using normally open dry contact connections.
The connection to the input is monitored for fault (open or short
circuit) and Alarm conditions.
The interface is used to monitor the contacts of an external system
which must be interfaced to the Fire Alarm System, for example a
Flow Switch in a sprinkler system to indicate if the sprinklers have
been activated or extinguishant level monitoring in Gas
Extinguishing systems etc.
The module is powered by the detection loop and is available as an electronic module with four fixing holes
or as a boxed unit for field installation.
Resistance values
Fault - Short circuit to 2K2 or 50k to Open Circuit
Normal - 8K2 to 50k
Fire 2K2 to 8K2
ADDRESS
SETTING
LOOP IN
4K7
END OF LINE
MONITORING
RESISTOR 22K
22K
ALARM RESISTOR (4K7) IN SERIES
WITH N/O CONTACT
LOOP OUT
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
50 x 45 x 20mm
LOOP CURRENT QUIESCENT
0,7mA
WEIGHT (UNBOXED)
30 grams
LOOP CURRENT MAX. (Alarm, LED illuminated) 3,1mA
OPERATING TEMPERATURE
0 - 40ºC
PROTECTION CATEGORY
STORAGE TEMPERATURE
-10 - 50ºC
HUMIDITY
< 85%Rh non condensing
ORDERING INFORMATION
INPUT
MAX CABLE SIZE
N/A
2,5 mm
2
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
CCPI
G LO B A L
FIRE
Conventional Control Panel Interface
EQUIPMENT
Features:
The Control panel interface provides eight individually addressed normally open inputs and two pre-defined
outputs. The interface permits the connection of a conventional fire alarm control panel with up to eight
Zones to the Global Fire Analogue Addressable Fire Control
panel via the detection loop.
The outputs are pre-defined as Silence and Reset and allow
these functions on the conventional panel to be executed
from the Addressable system. An external 24 volt DC supply is
required to power the onboard relays. This supply is optically
isolated from the detection Loop. The silence and reset relay
operations are indicated by two green LEDs.
Each CPI occupies 8 addresses on the Loop even when not all
inputs are used. See address setting chart below.
24 VOLTS
EXTERNAL
SUPPLY
Inputs
Inputs A- H ( Zones 1-8)
driven by Zone repeater
outputs of conventional panel.
SILENCE
OUTPUT
N/O
RESET
OUTPUT
N/O
ON
1 2 3 4
1234
0000 = 1 TO 8
1000 = 9 TO 16
0100 = 17 TO 24
1100 = 25 TO 32
0010 = 33 TO 40
1010 = 41 TO 48
0110 = 49 TO 56
1110 = 57 TO 64
0001 = 65 TO 72
1001 = 73 TO 80
0101 = 81 TO 88
1101 = 89 TO 96
0011 = 97 TO 104
1011 = 105 TO 112
0111 = 113 TO 120
Output Relays
Two N/O.
Output A Reset function
Output B - Silence
Contact rating 50Vdc, 1A Resistive Loading
0V
LOOP IN
0 = OFF
1 = ON
INPUTS 1- 8
LOOP OUT
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
88 x 74x 20 mm
LOOP CURRENT QUIESCENT
0,7mA
WEIGHT (UNBOXED)
60 grams
LOOP CURRENT INPUT ALARM
N/A
OPERATING TEMPERATURE
0 - 40ºC
LOOP CURRENT MAX. RELAY ACTIVE
N/A
STORAGE TEMPERATURE
-10 - 50ºC
RELAY CONTACT RATING
50 Vdc / 1A Resistive
HUMIDITY
<85 % Rh non condensing
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
PROTECTION CATEGORY
N/A
EXTERNAL CURRENT QUIESCENT
3 mA
MAX CABLE SIZE
2,5 mm2
EXTERNAL CURRENT MAX.
15mA
ORDERING INFORMATION
CCPI
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
ZMU
Zone Monitoring Unit
G LO B A L
FIRE
EQUIPMENT
Features:
The ZMU is a fully monitored interface module which is used to connect a number of current limited
conventional detectors to the Global Fire Addressable control panel via the detection loop. These
detectors are then seen as one address at the addressable control
panel.
The module can be powered from the Loop or optionally by an
external power supply in which case the jumpers J1 and J2 should be
removed. The detector line is monitored by a 4K7 resistor. A bi-colour
LED is used to signal the status of the module.
Green Normal
Red
Alarm
Extinguished - Fault
The external power, if used, is also monitored with the module
reporting a Fault if external power is not present.
As the current drawn from the loop can be significant, particularly in Fire and Short Circuit fault conditions,
the number of ZMUs that can be connected to a loop is limited to six depending on Loop load.
4K7
EXTERNAL SUPPLY
FOR ZONE
L1 OUT
L1 IN
L2
L1 OUT
L1 IN
L2
J1 & J2
ADDRESS
SETTING
NOTE: IF USED WITH EXTERNAL
POWER SUPPLY, (J1 & J2)
SHOULD BE OPEN
LOOP OUT
LOOP IN
SPECIFICATIONS
SUPPLY
Loop Power / 24Vdc
DIMENSIONS (UNBOXED)
60 x 60 x 20 mm
LOOP CURRENT QUIESCENT
2,9mA
WEIGHT (UNBOXED)
30 grams
LOOP CURRENT ALARM
3,1mA
OPERATING TEMPERATURE
0 - 40ºC
LOOP CURRENT FAULT - OPEN/SHORT
1,5/1,5mA
STORAGE TEMPERATURE
-10- 50ºC
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
HUMIDITY
<85 %Rh non condensing
EXTERNAL CURRENT QUIESCENT
7mA
MAX CABLE SIZE
2,5 mm2
EXTERNAL CURRENT ALARM
30mA
MAX NºOF ZMU PER LOOP
Load dependent- 6 Max
EXTERNAL CURRENT FAULT - OPEN/SHORT
1,5/60mA
ORDERING INFORMATION
ZMU
ISOLATION
500 Vdc Max.
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
3 I/O
G LO B A L
FIRE
Triple Input / Output Module
EQUIPMENT
Features:
The Triple Input/Output Module is a fully monitored device which permits the interfacing of third party
equipment with the Fire Alarm Control panel using three normally open dry contact connections while also
providing three changeover output relays to control ancillary
equipment. The connections to the input are monitored for fault (open
or short circuit) and Alarm conditions.
The output relays require an external 24Vdc supply. Relay operation
is confirmed by an onboard red LEDs, a yellow general Fault LED is
also provided.
The 3 I/O occupies three consecutive addresses on the detection
Loop.
The interface is used to monitor the contacts of an external system
which must be interfaced to the Fire Alarm System, for example a Flow
Switch in a sprinkler system to indicate if the sprinklers have been
activated or extinguishant level monitoring in Gas Extinguishing
systems etc.
VOLTAGE FREE
The output relays can be programmed to close fire
EXTERNAL SUPPLY
RELAY CONTACTS
FOR RELAYS
doors, activate smoke removal systems etc. An
external 24 volt DC power supply is required to
power the relays, this supply is optically isolated
from the Address Loop. The Addressable I/O
module is available as an electronic module with
four fixing holes.
ADDRESS
SETTING
Resistance values:
for Input
Fault -
Short circuit to 2K2 or 50k to Open Circuit
Normal - 8K2 to 50k
Fire -
2K2 to 8K2
Output Relay:
LOOP IN
Three N/O or N/C contacts.
Contact rating 50Vdc,
1A Resistive Loading
INPUT
CONNECTIONS
LOOP OUT
24 Vdc
EXTERNAL SUPPLY
Must connect to
24V power supply
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
88 x 72 x 20 mm
LOOP CURRENT QUIESCENT
0,7mA
WEIGHT (UNBOXED)
80 grams
LOOP CURRENT INPUT ALARM
3,1mA
OPERATING TEMPERATURE
0 - 40ºC
LOOP CURRENT MAX. RELAY ACTIVE
18,1mA
STORAGE TEMPERATURE
-10 - 50ºC
RELAY CONTACT RATING
50 Vdc / 1A Resistive
HUMIDITY
<85 %Rh non condensing
EXTERNAL SUPPLY VOLTAGE
24 Vdc nom
PROTECTION CATEGORY
N/A
EXTERNAL CURRENT QUIESCENT
3,1mA
MAX CABLE SIZE
2,5 mm2
EXTERNAL CURRENT MAX.
18,1mA
ORDERING INFORMATION
3 I/O
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
MCPA-KAC
KAC MANUAL CALL-POINT
G LO B A L
FIRE
EQUIPMENT
The MCPA-KAC is a BS 5839 compliant surface or flush mounting addressable manual call
point compatible with all GFE Addressable control panels.
With it's enhanced
communications mechanism, the typical
response time is approximately one second,
depending on the number of call points per loop.
A bi-colour LED flashes Green when the unit is
interrogated by the control panel and is
illuminated Red when activated. The command
to Illuminate the Red LED is emitted by the control
panel in response to activation of the individual
call point thus confirming that the Alarm signal
has been received at the control panel.
The
individual address, up to 125, of each call point
is set via an eight way DIL switch. The unit is supplied with a surface mount back box
...TO THE NEXT DEVICE
TOP
HAUT
OBEN
1
2
3
4
5
6
7
NO POLARITY FOR WIRES COMING FROM MODULE
OR
COMING FROM THE INSTALLATION
8
(SHADED AREA CONNECTS FROM MODULE ONLY)
ADDRESS
SETTING
LOOP IN
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
87 x 87 x 50 mm
LOOP CURRENT QUIESCENT
0,35mA
WEIGHT (UNBOXED)
150 grams
OPERATING TEMPERATURE
0-85ºC
LOOP CURRENT MAX (Alarm, LED Illuminated) 3,1mA
MAX. RECOMMENDED PER LOOP
30
HUMIDITY
<85%Rh non condensing
MAX CABLE SIZE
2,5 mm2
PROTECTION CATEGORY
IP 240
ORDERING INFORMATION
MCPA-KAC
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
MCPA-LP-FLAP
G LO B A L
FIRE
ADDRESSABLE MANUAL CALL POINT
EQUIPMENT
LOW PROFILE WITH PROTECTIVE COVER
The MCPA-LP-Flap is a low profile surface mounting addressable manual call point compatible with all GFE
Addressable Control panels.
With its enhanced communications mechanism the typical response
time is approximately one second, depending on the number of call
points connected to the loop. A bi-colour LED flashes Green when
the unit is interrogated by the control panel and is illuminated Red
when in Alarm.
The command to illuminate the Red LED is emitted by the control
panel in response to activation of the individual call point thus
confirming that the Alarm signal has been received at the control
panel.
The individual address, up to 125, of each call point is set via an
eight way DIL switch.
The unit is supplied complete with a hinged flap which protects the
trigger element from accidental activation and reduces malicious
activations as two actions are required to activate it.
Another convenient feature of the MCPA-LP-Flap is that after an activation the plastic insert is easily reset using
the supplied key, replacement is not required.
ADDRESS
SETTING
ON
1 2 3 4 5 6 7 8
ADDRESS
L1 L1 L2 L2
LOOP OUT
LOOP IN
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
90 x 90 x 28 mm
LOOP CURRENT QUIESCENT
0,35mA
WEIGHT (UNBOXED)
80 grams
OPERATING TEMPERATURE
0-50ºC
LOOP CURRENT MAX (Alarm, LED Illuminated) 3,1mA
MAX. RECOMMENDED PER LOOP
30
HUMIDITY
<85%Rh non condensing
MAX CABLE SIZE
2,5 mm2
PROTECTION CATEGORY
IP 24
ORDERING INFORMATION
MCPA-LP-FLAP
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
EQUIPMENT
GFE-MCPA
ADDRESSABLE MANUAL CALL POINT
The GFE-MCPA is an Analogue Addressable Manual Call Point, designed and manufactured to comply with
EN-54 part 11, compatible with all GFE Addressable Control panels.
With its enhanced communications mechanism the typical response
time, when in alarm, is approximately one second, depending on
the number of call points connected to the device loop.
A bi-colour LED flashes Green when the unit is interrogated by the
control panel and is illuminated Red when in Alarm.
The command to illuminate the Red LED is emitted by the control
panel in response to activation of the individual call point thus
confirming that the Alarm signal has been received at the control
panel.
The individual address, up to 125, of each call point is set via an
eight way DIL switch.
The unit is supplied complete with a hinged flap which protects the
trigger element from accidental activation and reduces malicious
activations as two actions are required in order to activate the device.
This unit can be both surface and flush mounted and it can be easily reset using the supplied key after
activation.
CONNECTIONS
Although this device is not polarised, please ensure that both loop connections, are
kept on the same terminal in all the modules. This is a wiring policy that should
apply to all devices in the loop regardless of them being non-polarity sensitive.
Switches 1-7
used to configure the Manual Call Point address.
Switch 8
Not used
To next device
or + return to panel
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OFF
LOOP
OUT
1
ON
LOOP
RETURN
PANEL
ON
1
2
3
4
5
6
7
OFF
Address Switches binary weights
4 on =8 7 on = 64
1 on =1
5 on =16
2 on =2
6 on =32
3 on =4
8
To next device
or - return to panel
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS (UNBOXED)
92 x 92 x 54 mm
LOOP CURRENT QUIESCENT
0,5mA
WEIGHT (UNBOXED)
152 grams
OPERATING TEMPERATURE
-10ºC to +50ºC
LOOP CURRENT MAX (Alarm, LED Illuminated) 4mA
MAX. RECOMMENDED PER LOOP
30
HUMIDITY
95% - non condensing @ 40ºC
MAX CABLE SIZE
2,5 mm2
PROTECTION CATEGORY
IP 24
COLOUR/CASE MATERIAL
RED/ABS - Flame Retardant
ORDERING INFORMATION
GFE-MCPA
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
EQUIPMENT
MCPC-LP-FLAP
CONVENTIONAL MANUAL CALL POINT
LOW PROFILE WITH PROTECTIVE COVER
The MCPC-LP-FLAP is a low profile surface mounting
Conventional manual call point. A bi-colour LED flashes
Green when the unit is connected to a control panel and is
illuminated Red when in Alarm.
The unit is supplied complete with a hinged flap which protects the
trigger element from accidental activation and reduces malicious
activations as two actions are required to activate it.
Another convenient feature of the MCPA-LP-Flap is that after an
activation the plastic insert is easily reset using the supplied key,
replacement is not required.
L1 L1 L2 L2
MCPC-LP-FLAP
MCPC-LP-FLAP
CONTROL PANEL
EOL RESISTOR
SPECIFICATIONS
SUPPLY
N/A
DIMENSIONS (UNBOXED)
90 x 90 x 28 mm
CURRENT QUIESCENT
0,35mA
WEIGHT (UNBOXED)
80 grams
CURRENT MAX (Alarm, LED Illuminated)
3,1mA
OPERATING TEMPERATURE
0-50ºC
MAX. RECOMMENDED PER LOOP
N/A
HUMIDITY
<85%Rh non condensing
MAX CABLE SIZE
2,5 mm2
PROTECTION CATEGORY
IP 24
ORDERING INFORMATION
MCPA-LP-FLAP
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
EQUIPMENT
GFE-MCPC
CONVENTIONAL MANUAL CALL POINT
The GFE-MCPC is a surface mounting Conventional manual call
point.
A bi-colour LED flashes Green when the unit is connected to a
control panel and is illuminated Red when in Alarm.
The unit is supplied complete with a hinged flap which protects the
trigger element from accidental activation and reduces malicious
activations as two actions are required to activate it.
Another convenient feature of the GFE-MCPC is that after an
activation the plastic insert is easily reset using the supplied key,
replacement is not required.
L1 L1 L2 L2
GFE-MCPC
GFE-MCPC
CONTROL PANEL
EOL RESISTOR
SPECIFICATIONS
SUPPLY
N/A
DIMENSIONS (UNBOXED)
92 x 92 x 54 mm
CURRENT QUIESCENT
0,5mA
WEIGHT (UNBOXED)
152 grams
CURRENT MAX (Alarm, LED Illuminated)
4mA
OPERATING TEMPERATURE
-10ºC to +50ºC
MAX. RECOMMENDED PER LOOP
N/A
HUMIDITY
95% - non condensing @ 40ºC
MAX CABLE SIZE
2,5 mm2
PROTECTION CATEGORY
IP 24
COLOUR/CASE MATERIAL
RED/ABS - Flame Retardant
ORDERING INFORMATION
GFE-MCPC
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
VULCAN-2
EQUIPMENT
ADDRESSABLE SOUNDER - BEACON
Features:
With 15 different variations, the Vulcan 2 brings an exciting flexibility to the Global Fire Equipment range of
warning devices and interfaces. Up to 96 Vulcan 2 devices can be connected to a single Loop depending on
Loop Loading. In the case of combined Sounder and Beacon
devices the maximum number of devices should not exceed 64.
The addressable Vulcan 2 is available as an Addressable Sounder,
Beacon or combined Sounder / Beacon which may be field
configured as a Shadow Sounder / Beacon or Auxiliary Sounder /
Beacon. There are also versions available incorporating an
isolator.
All Vulcan 2 devices have dip-switch Address setting while Tone
selection is via a jumper. Shadow Sounder and Auxiliary Sounder
settings are also achieved using the 8 way dip switch and a jumper
respectively. There is also a potentiometer which may be used to adjust the sound level if required.
Normally the Vulcan 2 will be used in conjunction with a detector however a White or Transparent lid is
available as an option for the Addressable Vulcan 2.
VULCAN 2 VARIANTS DESCRIPTION
SHADOW Sounder / Beacon.
The Vulcan 2 Addressable Sounder / Beacon can be configured as a Shadow Sounder/ Beacon using the 8
way dip switch provided. A Shadow Sounder / Beacon does not have an individual address thus freeing up
addresses for more detection devices. Shadow sounders / Beacons do not report back to the control panel so
their presence on the Loop is not monitored, however they do draw current from the Loop and must be
included in Loop load calculations. The number of combined Sounder / Beacons connected to a Loop should
not exceed 64 or 96 in the case of a Beacon or Sounder only.
Auxiliary Sounder / Beacon
When the Vulcan 2 is configured as an Auxiliary device the Sounder / Beacon shares the same address as the
detector with which it is co-located. Configuration of this mode is done via the jumper provided. When
operating in this mode the Vulcan 2 monitors the Address loop for the command from the control Panel to the
detector to illuminate it's LED. When this command is received the Vulcan 2 is also activated. If a Fire is
confirmed the remaining sounders may be activated using the Evacuate command. This reduces the
inconvenience to other guests in the event of a false alarm while at the same time giving early warning to the
occupant of the room in the case of an actual Fire event. Pressing Sounder silence at the panel silences all
active sounders.
The maximum number of Auxiliary Sounder/Beacons is 63 and they can be allocated between address 1 and 63.
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
VULCAN-2
EQUIPMENT
ADDRESSABLE SOUNDER - BEACON
CONNECTIONS AND TONE CONFIGURATIONS
= JUMPER
Sounder
Detector
GFE
Vulcan 2
Addressable
Detector
Base
SWEEPING
TONE
Tone
Isolator
Beacon
ALTERNATING
LOW-FREQUENCY
TONE
ALTERNATING
HIGH-FREQUENCY
TONE
Mode
Address|A|B|S
LOOP
OUT
PANEL
LOOP
RETURN
Loop
In/Out
- Vol +
Volume
Adjustment
+ -
Loop
In/Out
CONTINUOUS
TONE
+ -
Place spare jumper
to select Auxilliary
Sounder Mode
Switch 7
OFF Beacon stops with ALARM SILENCE
ON Beacon stops with RESET
Switch 6
Only used for Auxilliary Sounders
1
ON
OFF
1
ON
1
2
3
4
5
6
7
8
OFF
ON
2
3
4
5
6
7
8
Switch 8
OFF Shadow Sounder Operation.
ON Normal sounder operation.
2
3
4
5
6
7
8
OFF
Address Switches binary weights
3 on =4 5 on = 16
1 on =1
4 on =8 6 on = 32
2 on =2
29.0 mm
Order Code
Product Description
VULCAN 2 AS
VULCAN 2 ADDRESSABLE BASE SOUNDER
VULCAN 2 ASI
VULCAN 2 ADDRESSABLE BASE SOUNDER WITH ISOLATOR
VULCAN 2 ASB
VULCAN 2 ADDRESSABLE BASE SOUNDER WITH BEACON
VULCAN 2 ASBI
VULCAN 2 ADDRESSABLE BASE SOUNDER WITH BEACON WITH ISOLATOR
VULCAN 2 AB
VULCAN 2 ADDRESSABLE BEACON
VULCAN 2 ABI
VULCAN 2 ADDRESSABLE BEACON WITH ISOLATOR
VULCAN 2 L
LID FOR VULCAN 2
VULCAN 2 LT
TRANSPARENT LID FOR VULCAN 2
100.00 mm
Switches 1-5
used to configure the Sounder/ Beacon address.
37.5 mm
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS
Dia: 100mm
SOUND OUTPUT - Low Frequency 800-1000Hz
80 dB @ 1 metre
WEIGHT
120 grams (incl. lid)
SOUND OUTPUT - High Frequency 2400-3000Hz
85 dB @ 1 metre
OPERATING TEMPERATURE
0-50ºC
CURRENT CONSUMPTION - QUIESCENT
1,1mA
HUMIDITY
<85%Rh non condensing
CURRENT CONSUMPTION - SOUNDER - LOW FREQ
4mA
PROTECTION CATEGORY
Ip44
CURRENT CONSUMPTION - SOUNDER - HIGH FREQ
7mA
ENCLOSURE MATERIAL
Flame Retardant rating 94V0
CURRENT CONSUMPTION - BEACON
2.5mA
CURRENT CONSUMPTION - COMBINED - LOW FREQ
5.5mA
CURRENT CONSUMPTION - COMBINED - HIGH FREQ
8.5mA
H: 37.5mm
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
VULCAN-WSA
EQUIPMENT
ADDRESSABLE WALL SOUNDER
Features:
The VULCAN-WSA is a surface mount Addressable sounder with low power consumption available in either
Red or White housings. Up to 32 individually addressed sounders
can be installed per loop occupying address 94 to 125. The address
is set using switches 1 to 5 of the 6 way DIL switch.
Four different tones are available and selected by jumpers. The
Sound level can be lowered if required using the potentiometer.
When individual address reporting is not required, VULCAN-WSA
can be ordered as a Shadow sounder. In this case sounders do not
have an address number thus freeing up addresses for more
detection devices.
Shadow sounders do not report back to the control panel so their
presence on the loop is not monitored. Shadow sounders draw
current from the loop (3.5mA in alarm) and must be included in loop load calculations.
1
TO
DETECTOR
BASE
2
3
1
3
2
3
4
5
6
4
2
5
1
6
L1 L1 L2 L2
4
5
6
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SWEEPING
TONE
ALTERNATING
HIGH-FREQUENCY
TONE
ALTERNATING
LOW-FREQUENCY
TONE
CONTINUOUS
TONE
SWITCHES 1-5: REGULAR ADDRESSES FROM 094 TO 125 IN BINARY
SWITCH 6: OFF: GFE LOOP SOUNDER
ON: APOLLO SOUNDER CIRCUIT CONTROLLER
= JUMPER
SHADOW CONFIGURATION: FACTORY SET OPTION
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS
Dia: 100mm
LOOP CURRENT QUIESCENT
0,9mA
WEIGHT
125 grams
LOOP CURRENT ALARM
3,5mA
OPERATING TEMPERATURE
0-50ºC
MAX CABLE SIZE
2,5 mm2
HUMIDITY
<85%Rh non condensing
SOUND OUTPUT - Continuous/Sweep/Alternating LF
85dB @ 1 metre
PROTECTION CATEGORY
Ip44
SOUND OUTPUT - Alternating HF
92dB @ 1 metre
ADDRESS RANGE
94-125
ORDERING INFORMATION
VULCAN-WSA
H: 67mm
VULCAN-WSA/S for Shadow:
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
VULCAN-WSC
EQUIPMENT
CONVENTIONAL WALL SOUNDER
Features:
The Vulcan WSC is a low consumption sounder designed to be used
as an unobtrusive low profile sounder or as a base sounder to be
installed in conjunction with a conventional detector. This leads to
reduced installation costs and improves the aesthetics of the fire alarm
system.
Four different tones are available and selected by jumpers. The Sound
level can be lowered if required using the potentiometer.
ALTERNATING
LOW-FREQUENCY
TONE
SWEEPING
TONE
+ +
C- C-
ALTERNATING
HIGH-FREQUENCY
TONE
= JUMPER
NOTE: TO OBTAIN CONTINUOUS TONE
CONNECT 0V TO C- TERMINALS (SHORT BETWEEN - AND C-)
SPECIFICATIONS
SUPPLY
17-40 Vdc
DIMENSIONS
Dia: 100mm
CURRENT QUIESCENT
0,9mA
WEIGHT
125 grams
CURRENT ALARM
3,5mA
OPERATING TEMPERATURE
0-50ºC
MAX CABLE SIZE
2,5 mm2
HUMIDITY
<85%Rh non condensing
SOUND OUTPUT - Continuous/Sweep/Alternating LF
85dB @ 1 metre
PROTECTION CATEGORY
IP44
SOUND OUTPUT - Alternating HF
92dB @ 1 metre
ORDERING INFORMATION
VULCAN-WSC
H: 67mm
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
SOUNDERS
EQUIPMENT
ADDRESS SETTING
Sounder/ Beacon Address Settings
Sounder 1
1
2
4
3
5
6
7
Sounder 2
8
1
2
4
3
5
6
7
Sounder 3
8
1
2
4
3
5
6
7
Sounder 4
8
1
2
4
3
5
6
7
Sounder 5
8
1
2
4
3
5
6
7
Sounder 6
8
1
2
4
3
5
6
7
Sounder 7
8
1
2
4
3
5
6
7
Sounder 8
8
1
2
4
3
5
6
7
8
94
95
96
97
98
99
100
101
Sounder 9
Sounder 10
Sounder 11
Sounder 12
Sounder 13
Sounder 14
Sounder 15
Sounder 16
1
1
1
1
1
1
1
1
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
102
103
104
105
106
107
108
109
Sounder 17
Sounder 18
Sounder 19
Sounder 20
Sounder 21
Sounder 22
Sounder 23
Sounder 24
1
1
1
1
1
1
1
1
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
2
4
3
5
6
7
8
110
111
112
113
114
115
116
117
Sounder 25
Sounder 26
Sounder 27
Sounder 28
Sounder 29
Sounder 30
Sounder 31
Sounder 32
1
1
1
1
1
1
1
1
2
4
3
5
6
7
8
2
118
4
3
5
6
7
8
2
119
4
3
5
6
7
8
2
120
4
3
5
6
7
8
2
121
4
3
5
6
7
8
2
122
4
3
5
6
7
8
2
123
4
3
5
6
7
8
2
4
3
5
6
7
8
125
124
Auxilliary Sounder/ Beacon Address Settings
1
2
3
4
5
6
7
8
1
2
3
01
1
2
3
4
5
6
7
8
1
2
3
09
1
2
3
4
5
2
3
4
5
6
7
8
1
2
3
2
3
4
5
6
7
8
1
2
3
2
3
4
5
6
7
8
1
2
3
2
3
4
5
6
7
8
1
2
3
2
3
4
5
57
1
2
3
4
5
4
5
4
5
4
5
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
58
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
59
1
2
3
4
5
4
5
4
5
4
5
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
60
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
61
1
2
3
4
5
4
5
4
5
4
5
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
62
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
3
7
8
1
2
3
4
5
6
7
8
1
2
7
8
1
2
3
4
5
6
7
8
7
8
1
2
3
4
5
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
3
4
5
6
7
8
1
2
3
4
5
6
7
8
6
7
8
48
6
7
8
55
6
8
40
47
6
7
32
39
6
6
24
31
6
5
16
23
6
4
08
15
54
6
4
07
46
53
6
8
38
45
6
7
30
37
6
6
22
29
6
5
14
21
6
4
06
13
52
6
4
05
44
51
6
8
36
43
6
7
28
35
6
6
20
27
6
5
12
19
6
4
04
11
50
6
4
03
42
49
1
8
34
41
1
7
26
33
1
6
18
25
1
5
10
17
1
4
02
1
2
3
4
5
56
6
7
8
63
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
SAM
EQUIPMENT
SELF ADDRESSABLE MODULE
Following GLOBAL's strategy of providing competitive products for our esteemed customers, we are pleased to
announce the launch of SAM. This tiny, very low cost, module
provides any conventional detector with an address without
the inconvenience of using a manual addressing unit or DIP
switch.
The SAM is simply attached to the conventional
detector and the detector address is automatically assigned
to each SAM by the JUNO-NET or JUNiOr control panel
during commissioning and testing. A SAM based system
tolerates loop branches and can monitor loop interruptions
and head removal. SAM is ideal for low budget retrofits
where fire point identification is needed but the cost of fitting a fully analogue system is too high. SAM is also an
option in low budget installations that would normally be implemented with 4 to 8 zone conventional systems. It
gives you the cable savings possible (see below) with an addressable system, together with the loop sounder
capability but without the extra costs of analogue addressable heads. Compatible with most conventional
detectors, the SAM is fully encapsulated in a plastic case, unobtrusive and easy to connect to the detector base.
CONNECTION INFORMATION
Verify that all SAM connections, both to the loop and the associated conventional device (i.e. smoke
sensor/detector, call point, etc.) are properly made and that the conventional device connections follow the
manufacturer's instructions, in particular those regarding polarity. Reversal of the supply polarity can cause
failure or malfunction and prevent a SAM from being programmed.
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS
48 x 24 x 9 mm
LOOP CURRENT QUIESCENT
1,1mA
WEIGHT
85 grams
LOOP CURRENT ALARM
10mA
OPERATING TEMPERATURE
0-50ºC
MAX CABLE SIZE
2,5 mm2
HUMIDITY
<85%Rh non condensing
ADDRESS RANGE
1-125
PROTECTION CATEGORY
IP44
ORDERING INFORMATION
SAM
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
MAM
G LO B A L
FIRE
EQUIPMENT
MANUALLY ADDRESSABLE MODULE
Following the success of our Self Addressing Module (SAM) which permitted the connection
and individual addressing of conventional detectors and manual call points to our Junior
and Juno-Net control panels, Global Fire Equipment is pleased to introduce the Micro
Address Module(MAM).
The MAM takes the SAM concept to a higher level permitting not only the connection and
addressing of conventional detectors and call points but also offering a Micro Input, Micro
Output and conventional Sounder or Beacon driver/address Module.
(MAM-LSC)
With its small physical size and convenient 8 way DIL switch for address setting and
configuration, the MAM provides the facility to upgrade all the components of a
conventional system to a full addressable system, ideal for retrofit installations. The MAM is
fully compatible with all our standard address modules, addressable sounders,
addressable manual call points and WizMart detectors facilitating extensions to existing
systems.
To assist easy identification the MAM is supplied in 3 coloured plastic housings.
Red: Manual call point interface / Micro Input Module
Mustard: Micro Output Module / LOOP SOUNDER/ BEACON Controller
To Detector
White: Smoke / Heat Detector interface.
Loop IN &+
or other device
T1 & T3
Loop OUT &+
T2 & T4
CONNECTION INFORMATION
Verify that all MAM connections, both to the loop and the associated conventional device (i.e. smoke
sensor/detector, call point, etc.) are properly made and that the conventional device connections follow the
manufacturer's instructions, in particular those regarding polarity. Reversal of the supply polarity can cause
failure or malfunction of the conventional device.
8
OFF
ON
1
1 2 3 4 5 6 7 8
X
X
X
8
OFF
ON
X
X
X
CALL-POINT
X
X
7
=BEACON
ON (NO ALARM SILENCE)
1 2 3 4 5 6 7 8
X
X
X
(NON-ISOLATED)
8
ON
8
ON
ON
ON
ON
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
X
X
X
X
X
X
X
SMOKE
LSC
8
ON
X
7
=SOUNDER
OFF
2 3 4 5 6 7 8
8
OFF
ON
X
MICRO-INPUT
OUTPUT
(UNMONITORED)
(NON-ISOLATED)
X
X
X
X
HEAT
SPECIFICATIONS
SUPPLY
Loop Power
DIMENSIONS
48 x 24 x 9 mm
LOOP CURRENT QUIESCENT
1,1mA
WEIGHT
85 grams
LOOP CURRENT ALARM
10mA
OPERATING TEMPERATURE
0-50ºC
MAX CABLE SIZE
2,5 mm2
HUMIDITY
<85%Rh non condensing
ADDRESS RANGE
1-125
PROTECTION CATEGORY
IP44
ORDERING INFORMATION
MAM
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
J-NET-INT-FO
G LO B A L
FIRE
EQUIPMENT
FIBRE OPTIC INTERFACE
The J-NET-INT-FO interface modules allow GFE's range of panels to be interfaced to repeaters and/or subpanels using fibre optic cable using a common data communication loop in a ring topology. These units also
use a double-redundant data communication loop for extra security and reliability.
These modules are used in the fire alarm control panel to provide a communications interface for the
following:
1)
2)
3)
An Orion conventional panel and its repeater(s).
A Junior, analogue addressable panel, and its mini-repeater(s).
A Juno Net panel and Juno Net Repeater(s), Mini-Repeater(s) and or Sub-Panels.
The interface module is compatible with the following panels, repeaters and sub-panels:
1)
2)
3)
4)
5)
6)
7)
Orion Conventional Panel 2, 4 and 8 zones.
Orion Repeater.
Junior, 1 loop analogue addressable panel, non-expandable.
Mini-Repeater.
Juno Net, expandable analogue addressable panel.
Juno Net Repeater
Sub-Panel.
These interfaces can be used in parallel with other similar modules using other interface technologies such as
RS-232, RS-485 and TCP/IP, providing the installer with the tools to interface and create a network of panels,
repeaters and sub-panels using mixed data communication technologies, catering for the most demanding
applications and networking requirements.
Each panel, repeater and sub-panel will require one of these interface modules. The maximum ring distance
is 4 Kms.
Fibre optic cables to be used in conjunction with these modules should be multi-mode 62.5/125um and
terminated using the industry standard ST connectors.
Custom made versions of these modules can be produced for connection to GFE's proprietary MPX protocol
to connect leds, mimic displays, relays and conventional sounder circuits to GFE's extensive range of
conventional and analogue addressable panels. Please consult GFE for further information.
Warning: Disconnect all power sources including primary (electrical mains) and secondary (batteries)
supplies, before connecting or disconnecting these interface modules and/or any other internal circuit
boards.
SPECIFICATIONS
SUPPLY VOLTAGE
18-29 V DC (28 V DC nominal)
CURRENT CONSUMPTION
15 mA
CONNECTOR TYPE (FO)
ST Connectors
FIBRE OPTICS CABLE
Multi-mode 62.5/125 um
MAX DATA LOOP LENGTH
4 Kms
HARDWARE COMPATIBILITY
Juno Net, Junior, Juno Net Repeater
DIMENSIONS
135 - 35.6 mm
Mini Repeater and Sub-Panels
WEIGHT
32 grams
SOFTWARE COMPATIBILITY
Juno Net, Junior, Juno Net Repeater
Mini Repeater and Sub-Panels
(all software versions)
(all board versions)
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
G LO B A L
FIRE
EQUIPMENT
J-NET-INT-FO
FIBRE OPTIC INTERFACE
Notes:
On Junior Panel interface JP1 and JP2 should be removed.
On Mini-Rep interface JP1 and JP2 should be ON
Interface CON2 or CON3 should be connected to DATA CON
on Junior Version 3 panel and to CON3 or CON4 on Mini-Rep
or Junior Version 2 main board.
Always use ST type connectors for the FO terminations.
Optional Connections
Mini-Rep
Junior Panel
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
GFE-AD
G LO B A L
FIRE
EQUIPMENT
ANALOGUE ADDRESSABLE DETECTORS
The GFE-AD series of Analogue Addressable Detectors have been designed to be fully compatible with the
Global Fire Equipment range of intelligent control panels, Junior and Juno-Net. Compliant to EN54 (parts 5
6 7) and certified by DIFT fo CPD compliance, the GFE-AD series
detectors are available in oprical, Heat and combined Smoke/Heat
detector versions.
EN54 certificate:
GFE-AD-SL: EN54 pt7:2000 Certificate nº 0845-CPD-232-1483
GFE-AD-HL: EN54 pt5:2000 Certificate nº 0845-CPD-232-1482
GFE-AD-SHL: EN54 pt5 & pt7:2000 Certificate nº 0845-CPD-232-1484
Product Features:
!
!
!
!
!
!
!
!
Dual LEDs for 360º visibility
Advanced detection and communication protocols
Easy installation and maintenance
Sleek low-profile housing
Durable sensor head, no need for replacement
SMD circuit board design. High quality and reliability guaranteed.
Five year limited warranty
Sensor Base Option: Regular 4 or 5 inch base.
THIS RANGE INCLUDES
MODEL
SMOKE
GFE-AD-SL
REMOTE
LED
EN-54
APPROVAL
CE APPROVAL
X
X
X
X
X
X
X
X
X
X
X
HEAT
X
GFE-AD-HL
GFE-AD-SHL
X
SENSOR SPECIFICATION
MODEL
THERMAL
GFE-AD-SL
VOLTAGE
DC
STANDBY
ALARM
CURRENT
CURRENT
(MAX.) (MAX.) LED ON
SURGE
CURRENT
(MAX.)
START-UP
TIME
(MAX.)
BASE MODEL
15 - 30V
370μA
4mA
370μA
30 sec
P/N774912
GFE-AD-HL
57ºC
15 - 30V
370μA
4mA
370μA
30 sec
P/N772912
GFE-AD-SHL
57ºC
15 - 30V
370μA
4mA
370μA
30 sec
P/N774912
Smoke Sensitivity:
Coverage:
Start-Up Current:
Reset Time:
Alarm Indicator:
Remote Output:
Temperature Range:
Humidity:
Dimensions:
Weight:
2.66 +/-1.11%/FT Obscuration (UL standard), 0.10-0.157dB/m (EN54 standard)
100 m2 (Smoke), 50m2 (Heat) - Height dependent
370μA Maximum
less than 10 seconds
Red LED
15mA max., diode gate
-10ºC to 50ºC
0 to 95% RH, no condensation or icing
100mm (dia) x 46mm (ht) with base
188g/set with base
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
GFE-C
G LO B A L
FIRE
EQUIPMENT
CONVENTIONAL DETECTORS
The GFE series conventional detectors have been designed and tested to EN54 and UL standards. Available
in optical Smoke, heat and combined Smoke/Heat detector
versions, the GFE conventional detectors are both reliable and
aesthetically pleasing.
EN54 certificate:
GFE-S-2L: EN54 pt7:2000 Certificate nº 0845-CPD-232-1489
GFE-H-2L: EN54 pt5:2000 Certificate nº 0845-CPD-232-1488
GFE-SH-2L: EN54 pt5:2000 Certificate nº 0845-CPD-232-1490
Product Features:
!
!
!
!
!
!
!
!
Dual LEDs for 360º visibility
Advanced detection and discrimination algorithms
Easy installation and maintenance
Sleek low-profile housing
Durable sensor head, no need for replacement
SMD circuit board design. High quality and reliability guaranteed.
Integrated heat detector for GFE-SH-2L
Sensor Base Option: Regular 4 or 5 inch base.
THIS RANGE INCLUDES
MODEL
SMOKE
GFE-S-2L
GFE-H-2L
GFE-SH-2L
HEAT
X
X
X
X
SENSOR SPECIFICATION
MODEL
THERMAL
GFE-S-2L
GFE-H-2L
GFE-SH-2L
57ºC
57ºC
Smoke Sensitivity:
Coverage:
Start-Up Current:
Alarm Load:
Reset Voltage:
Reset Time:
Alarm Indicator:
Remote Output:
Temperature Range:
Humidity:
Dimensions:
Weight:
VOLTAGE
DC
12 - 30V
10 - 35V
12 - 30V
REMOTE
LED
EN-54
APPROVAL
CE APPROVAL
X
X
X
X
X
X
STANDBY
CURRENT
(MAX.)
ALARM
CURRENT
(MAX.)
SURGE
CURRENT
(MAX.)
X
X
X
90μA
55μA
100μA
70mA
55mA
70mA
130μA
150μA
130μA
START-UP PERMISSIBLE
BASE MODEL
TIME
CURRENT
(MAX.)
(MAX.)
P/N774912
60 sec
80mA
60 sec
60 sec
80mA
80mA
P/N772912
P/N774912
2.31 +/-1.37%/FT Obscuration (UL standard), 0.10-0.14 dB/m (EN54 standard)
100 m2 (Smoke), 50m2 (Heat) - Height dependent
160μA Maximum
340 ohms + 3 volt drop
less than 1 volt
less than 1 second
LED continuously emitting red light
15mA max., diode gate
-10ºC to 50ºC
0 to 95% RH, no condensation or icing
100mm (dia) x 46mm (ht) with base
130g/set with base
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
GFE-AD-ISOLATOR
G LO B A L
FIRE
EQUIPMENT
The GFE-AD-ISOLATOR has been designed to provide protection
against short circuit faults on a GFE Junior or Juno-Net Analogue
Addressable systems. The isolator protects the loop in the event of a short
circuit by disconnecting the section of the loop where the short circuit has
occurred. When the fault has been rectified the isolating circuitry
reconnects the affected part of the System.
The GFE-AD-Isolator is delivered in a White round junction box with
knockouts that permit easy cable entry. Two Yellow LED indicators are
provided to indicate on which side of the Device there is a short circuit
(Loop In and Loop Out). This facilitates easy localisation of the fault as it is
not necessary to look for two isolators to confirm the location of the affected section.
The GFE-AD-Isolator is polarity sensitive and can be damaged if connected with reverse polarity. Please be sure to note
the polarity indicated at the wiring terminals.
Up to 32 devices may be fitted between each isolator (EN54) or 20 devices for BS5839 compliance.
Under Normal conditions the GFE-AD-Isolator provides a low resistance of 0.3Ω in either direction. When a short
circuit condition is detected the isolator switches to the open state thereby isolating the Loop “IN” and Loop “OUT” lines.
The isolated section is tested every 3 seconds with a voltage pulse and is automatically reconnected when the load
resistance is greater than 175Ω.
Maximum no. Of devices between 2 Isolators: 32 devices. En54 pt.2
Short Circuit Voltage 0V
Loop Voltage aprox. 28 V DC
Detector
MCP
+
+
ISOLATOR
-
Loop In
Loop Out
MCP
-
Detector
ISOLATOR
Loop Out
-
Short Circuit
MCP
Short Circuit LED indicators are ON
PANEL
Loop Voltage aprox. 28 V DC
Loop Voltage aprox. 28 V DC
Detector
Loop Return
+
Loop Out
Detector
MCP
+
+
ISOLATOR
-
Loop In
-
Loop Out
MCP
Detector
ISOLATOR
Loop In
Loop Voltage aprox. 28 V DC
Loop Out
+
Loop In
-
During the duration of the short circuit condition, between 2 isolators, the loop voltage will be removed (0V) and
the 2 led indicators (Yellow), 1 on each isolator, associated with the section where the short circuit is present will be
lit.
Panel will report an open/short on the loop fault. Devices between 2 isolators will be removed. If panel is in
ACTIVE mode (green status led permanently on) there will be a number of “ Device Removed” faults. The total
number of these faults will depend on the number of devices that are connected between the isolators with the
short circuit fault. See function 7.1 on the panel.
As soon as the short circuit condition is removed the loop voltage (28V DC nominal) is reapplied and normal
working conditions on the loop are restored. Although there is no need for the panel to be reset, in order to clear
the faults the panel has to be reset.
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
DATA SHEET
GFE-AD-ISOLATOR
G LO B A L
FIRE
EQUIPMENT
Commissioning
It is important that the system be fully tested after installation. In normal operating conditions, apply short circuits to the
wiring at various points to confirm the correct operation of the Isolators. The LED indicator in the direction of the short
circuit should be illuminated on 2 isolators. On one device it will be the Loop In Led on the other it will be the Loop out
Led.
Troubleshooting
Before investigating individual units for faults it is necessary to ensure that the system wiring is fault free. Earth faults on a
data loop or ancillary Zone wiring may cause communications errors. Many fault conditions in Addressable systems
are the result of simple wiring errors.
PROBLEM: LED illuminated constantly
PROBLEM: Failure to isolate a short circuit
POSSIBLE CAUSE: Short circuit on loop
POSSIBLE CAUSE: Incorrect wiring
Technical Data
Minimum Loop operating voltage
in normal conditions
Maximum Loop operating voltage
Minimum protocol pulse
Power up time
Operating current
Maximum Loop current
17VDC
40V DC
5V to 9V
<1.5mS
see Table 1
1A continuous
3A short circuit switching
0.2Ω
2 yellow Leds, Loop In and Out
175Ω
50ì S
See table 2
Dia:99mm H: 40mm (with lid)
0-95% RH, non-condensing
-20 to +60ºC
-30 to +80ºC
Indoor use only
On resistance
Isolation indication
Reconnection resistance
Isolation Time
Reconnection test
Dimensions
Operating humidity
Operating temperature
Storage temperature
Design environment
TABLE 1
Quiescent current
Current in isolated state
TABLE 2
Reconnection current pulse amplitude
Reconnection current pulse duration
Reconnection current pulse spacing
Reconnection resistance limit
18V
24V
28V
120 A
4mA
150 A
5.4mA
180 A
6.4mA
SPUR
CONNECTIONS
35-50mA
60-100mS
3-4 seconds
300-450
LOOP
CONNECTIONS
60-100mA
60-100mS
3-4 seconds
150-225
M.A.R.F (Mercado Abastecedor da Região de Faro), Sítio do Guelhim, Estoi, Armazéns F3 & F4, 8009-021 FARO, PORTUGAL
TEL.: +351 289 865 560 FAX.: +351 289 865 587 e-mail: global@globalfire.pt www.globalfire.pt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising